Contents Cable entries Cable entries Cable entries 1420920000 – 2013/2014 Introduction C.2 Standard cable glands – Plastic C.6 Standard cable glands – Brass C.9 EMC cable glands C.15 Standard cable glands – Stainless steel C.17 Klippon® Cable Glands C.19 Accessories – Lock nuts C.46 Accessories – Flat IP washer C.51 Accessories – Earthing rings C.55 Accessories – Shrouds C.57 Accessories – Washers C.59 Sealing plugs C.60 Adaptors C.67 Compensating elements C.69 C C.1 Introduction Cable entries Cable entries Weidmüller offers a variety of add-on components for a multitude of applications; complementing its wide range of enclosure products. In addition to cable glands in brass, plastic and stainless steel, we provide sealing plugs, pressure compensation elements, adaptors and matching accessories, including lock nuts, flat gasket seals and earthing rings. C As with the enclosures, the cable glands come in IP protective classes from IP 54 to IP 69K and can be used as required in industrial standard applications, EMC applications or indeed in explosive hazard areas. They have the appropriate approvals for use in these areas. Ex certified Klippon® cable glands also allow the connection of braided and shielded armour with or without a lead sheath, as well as single wire reinforcement and metal foil armoured cables and wires. They can be used in temperatures from -60 °C to +180 °C. C.2 Depending on the connector range and the application area, the cable glands, sealing plugs, adaptors, pressure compensation elements and accessories are certified and manufactured in line with the following standards: • EN 60423 (metric thread) • EN 40430 (PG and NPT thread) • EN 60079-0 (General ATEX regulations) • EN 60079-1 (Ex d ATEX regulations) • EN 60079-7 (Ex e ATEX regulations) • EN 60079-11 (Ex i ATEX regulations) • EN 50262 (strain relief) • EN 60529 (IP protection degree) The range of cable glands, sealing plugs and pressure compensation elements is available in metric (M) and highstrength (PG) threads in sizes from M 12 to M 75 and PG 7 to PG 48. When choosing glands and sealing plugs, please refer to the table for the sealing characteristics of the O-rings, flat gaskets and seal inserts. The O-ring or flat gasket is always used to seal the connecting thread of an enclosure, while the seal insert for the cable gland actually seals and clamps the connection cable. 1420920000 – 2013/2014 Cable entries Introduction You should always observe the maximum drill-hole diameter when installing a cable gland, sealing plug, adaptor or pressure compensation element (e.g. onto the gland plate of an enclosure). These must not exceed the following specified maximum values / tolerances so that the protection degree of the whole enclosure can be guaranteed. Through-hole information M thread M 12 M 16 M 20 M 25 M 32 M 40 M 50 M 63 M 75 PG thread PG 7 PG 9 PG 11 PG 13.5 PG 16 PG 21 PG 29 PG 36 PG 42 PG 48 Overview of sealing materials for O-rings, flat gaskets as well as seal inserts Abbreviation TPE CR NBR EPDM FPM Trade name Santroprene Temperature range -40 °C...+130 °C Chemical resistance Hydrocarbons, oils, acids Fire resistant UL94, HB Chloroprene rubber Nitrile rubber Neoprene Perbunan, Nitrile -40 °C...+130 °C -40 °C...+130 °C Mineral oils, greases, fuels Hydrocarbons, oils, acids, aliphatic solvents, greases, fuels very good weak 40 - 90 40 - 90 Ethylene-propylene-diene rubber Fluoro-rubber Keltan -50 °C...+130 °C weak 20 - 90 very good Viton -25 °C...+200 °C Weather-, grease-, mineral oil-, chlorine,and ozone resistant, hydrocarbons ozone, oxygen, mineral oils, synthetic hydraulic fluids, fuels, aromatics, many organic solvents and chemicals weak 65 - 95 good Length in mm Length of thread in mm Diameter in mm Thickness in mm Threaded sealing ring or IP washer in mm Depth in mm Distance across flats in mm Clamping range in mm External thread Shroud Body torque in Nm Mounting torque in Nm Cap nut torque in Nm Packing unit in pieces 1420920000 – 2013/2014 Shore Free from halogens 64 Yes C Material Thermo-plastic elastomer Abbreviations – technical data A, L L1 D S GWDR S1,S2 SW KB Thread SUHB DR MODR DR HM Qty. Through-hole, in mm 12.2 16.2 20.2 25.2 32.2 40.2 50.2 63.2 75.2 Through-hole, in mm 12.4 15.1 18.5 20.4 22.5 28.3 37.4 47.2 54.2 59.5 No No UV resistance very good very good good Product designation VG VP KDSU KDSW KDSX KSG KUB KSPA KSPM KSWN KSWF KSP SKMU DAE BD EWS SZS ZE EMV SKS GWDR ZR Cable gland Sealing plugs Klippon® Double Seal Universal Klippon® Double Seal for SWA Klippon® Double Seal for SWB/STA Klippon® Standard Gland Klippon® Universal Barrier Klippon® Stopping Plug Type A Klippon® Stopping Plug Mushroom Klippon® Sealing Washer Nylon Klippon® Sealing Washer Red Fibre Klippon® Shroud PVC/Silicone Hexagon nut Pressure compensation element Breather drain (compensation element) Drain plug Serrated Star Washers Strain relief Electromagnetic compatibility Spiral kink protection Threaded sealing ring or IP washer Onion ring system (removable seal incisions system) C.3 Introduction Cable entries Glands and accessories The tables below provide an overview of the Weidmüller cable glands and the recommended accessories. Standard glands Approvals IP class of protection Ex without seal with seal Material/Type EMC Armouring Thread sealing rings CSM CR O-Ring GWDR PO GWDR…NR Locknuts grey black brass MS EMC SKMU…K GR SKMU…K SW SKMU…MS SKMU EMV... Plastic C VG … K67 IP 67 • VG … K68 IP 68 / 5 bar • VG … K68 SKS IP 68 / 5 bar • Nickel-plated brass VG … MS54 IP 54 IP 65 IP 68 / 5 bar, IP 69k VG … MS68 • optional included • VG … MS54-ZE IP 54 • VG…MS54 ZE BS IP 54 • VG…MS54 ZR IP 54 • VG … EMV IP 68 / 10 bar • included • VG … 1/EMV IP 68 / 5 bar, IP 69k • included • VG…SS68 IP 68 / 5 bar, IP 69k Stainless steel included • Cable glands Ex Approvals IP class of protection Ex without seal with seal Material/Type EMC Armouring Thread sealing rings CSM CR O-Ring GWDR PO GWDR…NR Locknuts grey black brass MS EMC SKMU…K GR SKMU…K SW SKMU…MS SKMU EMV... Nickel-plated brass, Ex KDSU...BN/BS O NI IP 68 / 2.5 bar KUB...BS O NI KDSW...BN/BS O/L NI IP 54 KDSX...BS O NI IP 54 KSG...BN/BS O NI Brass Ex KDSU...BN/BS O SC IP 66, IP 68 / 10 bar IP 54, IP 66, IP 68 / 2.5 bar IP 54, IP 66, IP 68 / 2.5 bar IP 66, IP 68 / 2.5 bar IP 68 / 2.5 bar KUB...BS O SC KDSW...BN/BS O/L SC IP 54 KDSX...BS O SC IP 54 KSG...BN/BS O SC IP 66, IP 68 / 10 bar IP 54, IP 66, IP 68 / 2.5 bar IP 54, IP 66, IP 68 / 2.5 bar IP 66, IP 68 / 2.5 bar Exe/d • included • Exe/d • included • Exe/d • optional • Exe/d • optional • Exe/d included • Exe/d • included • Exe/d • included • Exe/d • optional • Exe/d • optional • Exe/d included • Ex - Stainless steel glands on request C.4 1420920000 – 2013/2014 Cable entries Introduction Adaptor IP class of protection with seal Material/Type Approvals Thread sealing rings CSM CR O-Ring GWDR PO GWDR…NR Ex grey SKMU…K GR Locknuts black brass SKMU…K SW SKMU…MS MS EMC SKMU EMV... Plastic DAE M12 PA IP 66, IP 68, IP 69K included DAE M12 PA long IP 66, IP 68, IP 69K included C • Plastic Ex EWS • IP 54 • Stainless steel DAE M12 SS IP 66, IP 68, IP 69K • included • Stainless steel Ex BD 1 ss IP 66 • included BD 1 brass IP 66 • included KLIPPON BDX ... B IP 66 • included IP 66 • included Brass Ex Brass Ex Stainless steel Ex KLIPPON BDX ... S Stopping plugs Approvals IP class of protection without seal with seal Material/Type Ex Thread sealing rings CSM CR O-Ring GWDR PO GWDR…NR grey SKMU…K GR Locknuts black brass SKMU…K SW SKMU…MS MS EMC SKMU EMV... Plastic VP … K54 IP 54 • IP 65 Nickel-plated brass included • included • VP … MS65 IP 68 KSPM...SSC IP 66, IP 68 Exe/d IP 66, IP 68 Exe IP 66, IP 68 Exe Nitrile IP 68 Exe/d included Stainless steel Plastic Ex VP…Ex SW IP 66 KSPM...PL • optional • Nickel-plated brass, Ex VP…Ex MS KSPA…BNI IP 54 • • Ex d Brass Ex KSPM…BSC 1420920000 – 2013/2014 IP 66, IP 68 Exe/d included • C.5 Standard cable glands - Plastic Cable entries Cable glands - Plastic - IP 67 Inexpensive cable gland for industrial applications, without approvals. Thread C L SW L1 Technical data Material / Colour Seal insert Temperature range Protection degree Flammability rating Note Polyamide 6 / RAL 7035 CR -20 °C...80 °C IP 67 V-2 Version with moulded sealing lip Length L varies depending on the cable diameter used Ordering data Typ metric VG M12-K67 VG M16-K67 VG M16-K67 VG M20-K67 VG M20-K67 VG M25-K67 VG M32-K67 VG M40-K67 VG M50-K67 VG M63-K67 PG VG PG7-K67 VG PG9-K67 VG PG11-K67 VG PG13.5-K67 VG PG16-K67 VG PG21-K67 VG PG29-K67 VG PG36-K67 VG PG42-K67 VG PG48-K67 Note C.6 Thread KB L/L1 SW TRQ CN min. / max. TRQ BO min. / max. Qty. Order No. M 12 / 1.5 M 16 / 1.5 M 16 / 1.5 M 20 / 1.5 M 20 / 1.5 M 25 / 1.5 M 32 / 1.5 M 40 / 1.5 M 50 / 1.5 M 63 / 1.5 3-6.5 4-8 5-10 6-12 10-14 13-18 18-25 22-32 30-38 34-44 23.9 / 8 27.7 / 8 29 / 10 29.2 / 10 32.8 / 10 37.9 / 8 40.7 / 10 51.3 / 10 53.5 / 18 55 / 18 15 19 22 24 27 29 36 46 60 65 1.50 / 2.50 2.00 / 3.00 2.00 / 3.00 4.50 / 5.50 5.00 / 6.00 7.00 / 9.00 8.00 / 10.00 16.00 / 19.00 20.00 / 24.00 20.50 / 25.50 1.00 / 3.00 1.00 / 4.00 1.00 / 4.00 2.00 / 5.00 2.00 / 5.00 2.00 / 5.00 3.00 / 7.00 7.00 / 12.00 9.50 / 15.50 12.50 / 18.50 100 50 50 50 50 25 20 10 10 10 1909660000 1909670000 1909680000 1909690000 1909700000 1909710000 1909720000 1909730000 1909740000 1909750000 PG 7 PG 9 PG 11 PG 13.5 PG 16 PG 21 PG 29 PG 36 PG 42 PG 48 3-6.5 4-8 5-10 6-12 10-14 13-18 18-25 22-32 30-38 34-44 23.9 / 8 27.7 / 8 29 / 8 29.2 / 9 32.8 / 10 37.9 / 11 40.7 / 11 51.3 / 13 53.5 / 13 55 / 14 15 19 22 24 27 33 42 53 60 65 1.50 / 2.50 2.00 / 3.00 2.00 / 3.00 4.50 / 5.50 5.00 / 6.00 5.00 / 6.00 7.00 / 8.00 14.50 / 15.30 17.00 / 19.00 19.00 / 21.00 1.20 / 1.80 1.20 / 1.80 1.50 / 2.50 2.50 / 3.50 2.50 / 4.50 7.00 / 9.00 7.50 / 10.50 9.50 / 12.50 12.00 / 16.00 12.00 / 16.00 100 50 50 50 50 25 20 10 10 10 1909760000 1909770000 1909780000 1909790000 1909800000 1909810000 1909820000 1909830000 1909840000 1909850000 Integrated strain relief, halogen-free without sealing ring. 1420920000 – 2013 Standard cable glands - Plastic Cable entries Cable glands - Plastic - IP 68 Thread L1 L C SW Plastic cable gland with integrated strain relief for industrial applications requiring IP 68 protection. Technical data Material / Colour Seal insert Temperature range Protection degree Flammability rating Polyamide 6 / RAL 7035 CR -30 °C...80 °C IP 68 - 5 bar (30 min.) V-2 Note Version with moulded sealing lip Length L varies depending on the cable diameter used Ordering data Typ metric VG M12-1/K68 VG M16 - K 68 VG M16-1/K68 VG M20-1/K68 VG M25 - K 68 VG M25-1/K68 VG M32 - K 68 VG M32-1/K68 VG M40 - K 68 VG M40-1/K68 VG M50 - K 68 VG M63-1/K68 PG VG 7-K68 VG 9-K68 VG 11-K68 VG 13.5-K68 VG 16-K68 VG 21-K68 VG 29-K68 VG 36-K68 VG 42-K68 VG 48-K68 Note 1420920000 – 2013 Thread KB L/L1 SW TRQ CN min. / max. TRQ BO min. / max. Qty. Order No. M 12 / 1.5 M 16 / 1.5 M 16 / 1.5 M 20 / 1.5 M 25 / 1.5 M 25 / 1.5 M 32 / 1.5 M 32 / 1.5 M 40 / 1.5 M 40 / 1.5 M 50 / 1.5 M 63 / 1.5 3-6.5 5-10 4-8 6-12 13-18 11-17 18-25 15-21 22-32 19-28 30-38 34-44 32.4 / 8 39.7 / 10 35.7 / 8 41.2 / 10 48.2 / 10 43.2 / 8 50.8 / 18 50.7 / 10 69.9 / 18 55.2 / 10 71.7 / 18 72.9 / 18 15 22 19 24 33 29 42 36 53 46 60 65 1.50 / 2.50 2.00 / 3.00 2.00 / 3.00 4.50 / 5.50 7.00 / 9.00 7.00 / 9.00 8.00 / 10.00 8.00 / 10.00 16.00 / 19.00 16.00 / 19.00 20.00 / 24.00 20.50 / 25.50 1.00 / 3.00 1.00 / 4.00 1.00 / 4.00 2.00 / 5.00 2.00 / 5.00 2.00 / 5.00 3.00 / 7.00 3.00 / 7.00 7.00 / 12.00 7.00 / 12.00 9.50 / 15.50 12.50 / 18.50 100 50 50 50 25 25 20 20 10 10 10 10 1772280000 1772290000 1909860000 1772300000 1772310000 1909870000 1772320000 1909880000 1772330000 1909890000 1772340000 1772350000 PG 7 PG 9 PG 11 PG 13.5 PG 16 PG 21 PG 29 PG 36 PG 42 PG 48 3-6.5 4-8 5-10 6-12 10-14 13-18 18-25 22-32 30-38 34-44 30.5 / 8 34 / 8 37 / 8 39 / 9 42.5 / 10 48 / 11 53 / 11 65 / 13 68 / 13 69 / 14 15 19 22 24 27 33 42 53 60 65 1.50 / 2.50 2.00 / 3.00 2.00 / 3.00 4.50 / 5.50 5.00 / 6.00 5.00 / 6.00 7.00 / 8.00 14.50 / 15.50 17.00 / 19.00 19.00 / 21.00 1.20 / 1.80 1.20 / 1.80 1.50 / 2.50 2.50 / 3.50 2.50 / 4.50 7.00 / 9.00 7.50 / 10.50 9.50 / 12.50 12.00 / 16.00 12.00 / 16.00 100 50 50 50 50 25 20 10 10 10 1568970000 1568980000 1568990000 1569000000 1569010000 1569020000 1569030000 1569040000 1569050000 1718770000 Long-thread version on request, halogen-free without sealing ring C.7 Standard cable glands - Plastic Cable entries Cable glands - Plastic - SKS C SW Thread Plastic cable gland with spiral bending protection specially suited for flexible connections. L1 L Technical data Material / Colour Seal insert Temperature range Protection degree Flammability rating Note Polyamide 6 / RAL 7035 CR -30 °C...80 °C IP 68 - 5 bar (30 min.) V-2 Version with moulded sealing lip Length L varies depending on the cable diameter used Ordering data Typ metric VGM12-K68 SKS VGM16-K68 SKS VGM20-K68 SKS VGM20-K68 SKS VGM25-K68 SKS PG VG 9-K68 SKS VG 11-K68 SKS VG 13.5-K68 SKS VG 16-K68 SKS VG 21-K68 SKS Note C.8 Thread KB L/L1 SW TRQ CN min. / max. TRQ BO min. / max. Qty. Order No. M 12 / 1.5 M 16 / 1.5 M 20 / 1.5 M 20 / 1.5 M 25 / 1.5 3-6.5 5-10 6-12 10-14 13-18 65 / 8 90 / 10 106 / 10 116 / 10 129 / 10 15 22 24 27 33 1.50 / 2.50 2.00 / 3.00 4.50 / 5.50 5.00 / 6.00 7.00 / 9.00 1.50 / 2.50 2.00 / 3.00 2.00 / 5.00 2.00 / 5.00 2.00 / 5.00 100 50 50 50 25 1776700000 1776710000 1778860000 1776720000 1776730000 PG 9 PG 11 PG 13.5 PG 16 PG 21 4-8 5-10 6-12 10-14 13-18 79 / 8 89 / 8 105 / 9 117 / 10 130 / 11 19 22 24 27 33 2.00 / 3.00 2.00 / 3.00 4.50 / 5.50 5.00 / 6.00 5.00 / 6.00 1.50 / 2.50 1.50 / 2.50 2.50 / 3.50 2.50 / 4.50 7.00 / 9.00 50 100 50 25 20 1720480000 1720490000 1720500000 1720510000 1720520000 VDE for metric variants, halogen free, without sealing ring 1420920000 – 2013 Standard cable glands - Brass Cable entries Cable glands - Brass - IP 54 Standard brass cable gland for industrial applications that require IP 54 protection. L C SW2 Thread SW1 L1 Technical data Material Seal insert Temperature range Protection degree Brass, nickel-plated NBR -20 °C...60 °C IP 54 Note Optional sealing ring Length „L“ varies depending on the cable diameter used. Ordering data Typ metric VGM12-MS54 VGM12-MS54 VGM16-MS54 VGM20-MS54 VGM20-MS54 VGM25-MS54 VGM25-MS54 VGM32-MS54 VGM40-MS54 VGM50-MS54 VGM50-MS54 VGM63-MS54 PG VG 7-MS54 VG 9-MS54 VG 11-MS54 VG 13.5-MS54 VG 16-MS54 VG 21-MS54 VG 29-MS54 VG 36-MS54 VG 42-MS54 VG 48-MS54 Note 1420920000 – 2013 Thread KB L/L1 SW1/SW2 TRQ CN min. / max. TRQ BO min. / max. Qty. Order No. M 12 / 1.5 M 12 / 1.5 M 16 / 1.5 M 20 / 1.5 M 20 / 1.5 M 25 / 1.5 M 25 / 1.5 M 32 / 1.5 M 40 / 1.5 M 50 / 1.5 M 50 / 1.5 M 63 / 1.5 5-7 6-8 8-10 8-10 10-12 12-14 15-17 24-26 33-35 31-33 39-41 45-47 21.5 / 5 22 / 6 26 / 5 26.5 / 6 26.5 / 6.5 27.5 / 7 29.5 / 7 33 / 8 33 / 9 39 / 9 43 / 10 45 / 10 13 / 14 15 / 17 18 / 20 18 / 22 20 / 22 22 / 27 28 / 30 38 / 40 37 / 43 47 / 55 54 / 57 60 / 68 5.30 / 5.30 5.30 / 5.30 6.70 / 6.70 8.00 / 8.00 8.00 / 8.00 8.00 / 8.00 8.00 / 8.00 12.00 / 12.00 12.00 / 12.00 13.30 / 13.30 13.30 / 13.30 13.30 / 13.30 8.00 / 8.00 8.00 / 8.00 10.00 / 10.00 12.00 / 12.00 12.00 / 12.00 12.00 / 12.00 12.00 / 12.00 18.00 / 18.00 18.00 / 18.00 20.00 / 20.00 20.00 / 20.00 20.00 / 20.00 100 100 100 50 50 50 50 25 25 10 5 5 1778410000 1778400000 1778390000 1778380000 1778370000 1778360000 1778350000 1778340000 1778330000 1778320000 1778310000 1778300000 PG 7 PG 9 PG 11 PG 13.5 PG 16 PG 21 PG 29 PG 36 PG 42 PG 48 5-7 6-8 8-10 10-12 12-14 15-17 24-26 33-35 39-41 45-47 20.5 / 5 22 / 6 26 / 6 26 / 6.5 27 / 6.5 29.5 / 7 33 / 8 39 / 9 44 / 10 45 / 10 13 / 14 15 / 17 18 / 20 20 / 22 22 / 24 28 / 30 37 / 40 47 / 50 54 / 57 60 / 64 4.20 / 4.20 4.20 / 4.20 4.20 / 4.20 4.20 / 4.20 5.00 / 5.00 6.70 / 6.70 6.70 / 6.70 6.70 / 6.70 6.70 / 6.70 6.70 / 6.70 6.25 / 6.25 6.25 / 6.25 6.25 / 6.25 6.25 / 6.25 7.50 / 7.50 10.00 / 10.00 10.00 / 10.00 10.00 / 10.00 10.00 / 10.00 10.00 / 10.00 100 100 50 50 50 50 25 20 10 5 0521500000 0261500000 0260700000 0260800000 0261400000 0260900000 0261000000 0497600000 0497700000 1718780000 Further versions on request C.9 Standard cable glands - Brass Cable entries Cable glands - Brass - ZR Brass cable gland with incision seal for standard industrial applications. The seal insert which is used contains several removable or separable inlets. This enables cables with a diameter of 4 mm to 41 mm to be connected. L SW2 SW1 C Thread L1 Technical data Material Seal insert Temperature range Protection degree Brass, nickel-plated NBR -20 °C...80 °C IP 54 Note Ordering data Typ metric VG M20-MS54 VG M25-MS54 VG M32-MS54 VG M40-MS54 VG M50-MS54 PG VGPG13.5-MS54 VG PG16-MS54 VG PG21-MS54 VG PG29-MS54 VG PG36-MS54 VG PG42-MS54 Note C.10 Thread KB L/L1 SW1/SW2 TRQ CN, min. TRQ BO, min. D1 D2 D3 D4 Qty. Order No. M 20 / 1.5 M 25 / 1.5 M 32 / 1.5 M 40 / 1.5 M 50 / 1.5 4-13 8.5-18 16-26 23-30 32-40 26.5 / 6.5 27.5 / 7 33 / 8 33 / 33 39 / 39 22 / 24 28 / 30 37 / 40 47 / 50 54 / 57 3.05 3.66 4.88 4.88 4.88 6.25 7.50 10.00 10.00 10.00 4 8.5 16 23 32 7 11.5 19 26 35 10 14.5 22 29 38 13 18 25 32 41 50 25 25 10 5 1009560000 1009570000 1009580000 1009590000 1009600000 PG 13.5 PG 16 PG 21 PG 29 PG 36 PG 42 7.5-12.5 7.5-15 10-19 18-27 24-33 30-39 22 / 6.5 27 / 6.5 29.5 / 7 33 / 8 39 / 9 44 / 10 20 / 22 22 / 24 28 / 30 37 / 40 47 / 50 54 / 57 4.20 5.00 6.70 6.70 6.70 6.70 6.25 7.50 10.00 10.00 10.00 10.00 7.5 7.5 10 18 24 30 10 10 13 21 27 33 12.5 12.5 16 24 30 36 0 15 19 27 33 39 50 50 25 25 10 5 1009610000 1009620000 1009630000 1009640000 1009650000 1009670000 D1-D4 are the removable seal incisions from 4 mm to 41 mm. 1420920000 – 2013 Standard cable glands - Brass Cable entries Cable glands - Brass - IP 68 Standard brass cable gland for industrial applications that require IP 68 or IP 69K protection. L C SW1 SW2 Thread L1 Technical data Material O-ring / Seal insert Temperature range Clamp insert Protection degree with GWDR Brass, nickel-plated NBR / CR -40 °C...100 °C Polyamide IP 68 - 5 bar, IP 69K Note Length „L“ varies depending on the cable diameter used; IP 69K applies to all metric cable glands; the following thread sizes PG29, PG36, PG42 and PG48 are excluded from IP 69K. Ordering data Typ metric VG M12 - MS 68 VG M16 - MS 68 VG M16-1/MS68 VG M20 - MS 68 VG M25 - MS 68 VG M25-1/MS68 VG M32 - MS 68 VG M32-1/MS68 VG M40 - MS 68 VG M40-1/MS68 VG M50 - MS 68 VG M50-1/MS68 VG M63 - MS 68 PG (IP 69K) VG 7-MS68 VG 9-MS68 VG 11-MS68 VG 13.5-MS68 VG 16-MS68 VG 21-MS68 PG (IP68) VG 29-MS68 VG 36-MS68 VG 42-MS68 VG 48-MS68 Note 1420920000 – 2013 Thread KB L/L1 SW1/SW2 TRQ CN min. / max. TRQ BO min. / max. Qty. Order No. M 12 / 1.5 M 16 / 1.5 M 16 / 1.5 M 20 / 1.5 M 25 / 1.5 M 25 / 1.5 M 32 / 1.5 M 32 / 1.5 M 40 / 1.5 M 40 / 1.5 M 50 / 1.5 M 50 / 1.5 M 63 / 1.5 3-6.5 4-8 4.5-10 6-12 10-14 11-17 13-18 15-21 18-25 19-28 22-32 27-38 34-44 28 / 6 33 / 7 37.3 / 7 38 / 8 42 / 8 42 / 8 48 / 9 45 / 8 53 / 9 55.1 / 9 57 / 9 62.2 / 9 65 / 14 14 / 14 17 / 18 20 / 20 22 / 22 24 / 27 27 / 27 30 / 34 34 / 34 40 / 43 43 / 43 50 / 55 58 / 58 64 / 68 4.50 / 5.50 5.00 / 6.00 5.00 / 6.00 7.00 / 9.00 10.00 / 12.00 10.00 / 12.00 16.00 / 18.00 16.00 / 18.00 21.00 / 23.00 21.00 / 23.00 38.50 / 41.50 38.50 / 41.50 48.00 / 52.00 2.50 / 3.50 3.50 / 4.50 3.50 / 4.50 5.00 / 6.00 5.00 / 7.00 5.00 / 7.00 5.00 / 7.00 5.00 / 7.00 10.50 / 13.50 10.50 / 13.50 16.00 / 20.00 16.00 / 20.00 22.50 / 27.50 50 50 50 50 25 25 25 20 20 20 15 12 12 1772200000 1772210000 1909910000 1772220000 1772230000 1909920000 1772240000 1909930000 1772250000 1909940000 1772260000 1909950000 1772270000 PG 7 PG 9 PG 11 PG 13.5 PG 16 PG 21 3-6.5 4-8 5-10 6-12 10-14 13-18 28 / 6 28 / 6 31 / 6 31 / 6.5 34 / 6.5 39 / 7 14 / 14 17 / 17 20 / 20 22 / 22 24 / 24 30 / 30 4.50 / 5.50 5.00 / 6.00 6.50 / 7.50 7.00 / 9.00 10.00 / 12.00 16.00 / 18.00 2.50 / 3.50 3.50 / 4.50 4.50 / 5.50 4.50 / 6.50 6.00 / 8.00 9.00 / 11.00 50 50 50 50 25 25 1569060000 1569070000 1569080000 1569090000 1569100000 1569110000 PG 29 PG 36 PG 42 PG 48 18-25 22-32 30-38 34-44 47 / 8 57 / 10 60 / 12 63 / 14 40 / 50 50 / 50 58 / 58 64 / 64 21.00 / 23.00 38.50 / 41.50 43.00 / 47.00 48.00 / 52.00 13.50 / 16.50 18.00 / 22.00 25.00 / 29.00 32.50 / 37.50 20 15 12 12 1569120000 1569130000 1569140000 1718790000 Long-thread version on request VDE for metric version C.11 Standard cable glands - Brass Cable entries Cable glands - Brass - ZE Brass cable glands with external, centrally positioned strain relief provided by clamping jaws. The seal insert which is used contains several removable or separable inlets. L SW2 SW1 C Thread L1 Technical data Material Seal insert Temperature range Protection degree Brass, nickel-plated NBR -20 °C...80 °C IP 54 Note Optional sealing ring Length „L“ varies depending on the cable diameter used. Ordering data Typ metric VGM12-MS54 ZE VGM16-MS54 ZE VGM20-MS54 ZE VGM20-MS54 ZE VGM25-MS54 ZE VGM32-MS54 ZE VGM40-MS54 ZE VGM50-MS54 ZE VGM63-MS54 ZE PG VG 7-MS54-ZE VG 9-MS54-ZE VG 11-MS54-ZE VG 13.5-MS54-ZE VG 16-MS54-ZE VG 21-MS54-ZE VG 29-MS54-ZE VG 36-MS54-ZE VG 42-MS54-ZE VG 48-MS54-ZE Note C.12 Thread KB KB ZE L/L1 SW1/SW2 TRQ CN min. / max. TRQ BO min. / max. Qty. Order No. M 12 / 1.5 M 16 / 1.5 M 20 / 1.5 M 20 / 1.5 M 25 / 1.5 M 32 / 1.5 M 40 / 1.5 M 50 / 1.5 M 63 / 1.5 5-7 4-10 6.5-12.5 6.5-12.5 9-19 17-27 23-33 29-39 35-45 5.8-8 6.5-10 7.5-12 8.5-14 12-21 19-30 25-37 31-43 35-48 21.5 / 6 26 / 6 26.5 / 6.5 26.5 / 6.5 29.5 / 7 33 / 8 33 / 8 43 / 9 45 / 10 14 / 16 18 / 19 22 / 22 22 / 24 30 / 34 40 / 42 50 / 52 57 / 59 66 / 64 5.33 / 5.33 6.67 / 6.67 8.00 / 8.00 8.00 / 8.00 8.00 / 8.00 12.00 / 12.00 12.00 / 12.00 13.33 / 13.33 13.33 / 13.33 8.00 / 8.00 10.00 / 10.00 12.00 / 12.00 12.00 / 12.00 12.00 / 12.00 18.00 / 18.00 18.00 / 18.00 20.00 / 20.00 20.00 / 20.00 100 100 50 50 50 25 25 5 5 1778420000 1778440000 1778450000 1778460000 1778480000 1778490000 1778500000 1778520000 1778530000 PG 7 PG 9 PG 11 PG 13.5 PG 16 PG 21 PG 29 PG 36 PG 42 PG 48 5-7 4-10 6.5-12.5 6.5-12.5 6.5-15 9-19 17-27 23-33 29-39 35-45 5.8-8 6.5-10 7.5-12 8.5-14 9.5-17 12-21 19-30 25-37 31-43 35-48 27 / 5 30.5 / 6 31.5 / 6 32 / 6.5 33 / 6.5 38 / 7 43 / 8 49.5 / 9 53.5 / 10 55 / 10 14 / 16 17 / 19 20 / 22 22 / 24 24 / 27 30 / 34 40 / 40 50 / 50 57 / 57 64 / 64 4.20 / 4.20 4.20 / 4.20 4.20 / 4.20 4.20 / 4.20 5.00 / 5.00 6.70 / 6.70 6.70 / 6.70 6.70 / 6.70 6.70 / 6.70 6.70 / 6.70 6.25 / 6.25 6.25 / 6.25 6.25 / 6.25 6.25 / 6.25 7.50 / 7.50 10.00 / 10.00 10.00 / 10.00 10.00 / 10.00 10.00 / 10.00 10.00 / 10.00 50 50 50 50 50 50 25 10 5 5 1718800000 1718810000 1718820000 1718830000 1718840000 1718850000 1718860000 1718870000 1718880000 1718890000 Further versions on request 1420920000 – 2013 Standard cable glands - Brass Cable entries Cable glands - Brass - ZE - BS Industrial brass cable glands with strain-relief and trumpet-shaped anti-bend mechanism for connecting non-stationary cables and lines. The seal insert which is used contains several removable or separable inlets. SW2 Thread SW1 L1 C Technical data Material Seal insert Temperature range Protection degree Brass, nickel-plated NBR -20 °C...80 °C IP 54 Note Ordering data Typ metric VGM16-MS54ZE VGM16-MS54ZE VGM20-MS54ZE VGM20-MS54ZE VGM25-MS54ZE VGM32-MS54ZE Note 1420920000 – 2013 Thread KB KB ZE L/L1 SW1/SW2 TRQ CN min. / max. TRQ BO min. / max. Qty. M 16 / 1.5 M 16 / 1.5 M 20 / 1.5 M 20 / 1.5 M 25 / 1.5 M 32 / 1.5 4-10 6.5-12.5 6.5-12.5 6.5-15 9-19 17-27 6-9 8-12 8-12 10-15 14-20 18-27 5/6 34 / 5 37.8 / 6 37.8 / 6.5 44 / 7 50.8 / 8 18 / 22 20 / 26 22 / 26 24 / 32 30 / 38 40 / 50 6.70 / 6.70 6.70 / 6.70 8.00 / 8.00 8.00 / 8.00 8.00 / 8.00 12.00 / 12.00 10.00 / 10.00 10.00 / 10.00 12.00 / 12.00 12.00 / 12.00 12.00 / 12.00 18.00 / 18.00 50 50 50 50 25 25 Order No. 1005190000 1005200000 1005210000 1005220000 1005230000 1005240000 C.13 Standard cable glands - Brass Cable entries Clamping screws - Brass - IP 65 The halved cable glands are designed for use in HDC – RockStar® base and hoods. The seal insert which is used contains several removable or separable inlets. Ø 13 C pressure ring Thread AF pressing screw sealing ring Technical data Clamping screw material Sealing ring material Pressure ring material Temperature range Protection degree Brass, nickel-plated SBR/NBR Polyamide -20 °C...60 °C IP 65 Note Ordering data Typ metric VG H M20 MS VG H M25 MS VG H M32 MS VG H M40 MS PG KV 11-M KV 13-M KV 16-M KV 21-M KV 29-M Note C.14 Thread Inserts in mm SW Qty. Order No. M 20 / 1.5 M 25 / 1.5 M 32 / 1.5 M 40 / 1.5 4 / 7 / 10 / 13 8.5 / 11.5 / 14.5 / 18 16 / 19 / 22 / 25 23 / 26 / 29 / 32 20 25 32 40 50 25 20 10 1921720000 1921740000 1921760000 1921770000 PG 11 PG 13 PG 16 PG 21 PG 29 7.5 / 10 / 12.5 7.5 / 10 / 12.5 7.5 / 10 / 12.5 / 15 10 / 13 / 16 / 19 18 / 21 / 24 / 27 10 10 10 10 10 10 10 10 10 10 1656390000 1656400000 1656410000 1656420000 1656430000 1420920000 – 2013 EMC cable glands Cable entries Cable glands - Brass - EMC Brass cable gland for shielding against interference frequencies with a screening attenuation of up to 100 dB. Contact with cable shield by means of spring washer. L1 SW Thread C L Technical data Material O-Ring Temperature range Protection degree Clamp insert Note Brass, nickel-plated NBR -40 °C...135 °C IP 68 - 10 bar TPE Length „L“ varies according to cable diameter used Ordering data Typ metric VG EMV M18X1.5 VG EMV M20X1.5 VG EMV M24X1.5 VG EMV M25X1.5 PG VG EMV PG 7/9 VG EMV PG 9/11 VG EMV PG 11 VG EMV PG 13.5 VG EMV PG 16 K14 VG EMV PG 16 K18 VG EMV PG 21 K18 VG EMV PG K28 VG EMV PG 29 K26 VG EMV PG 29 K29 VG EMV PG36 K32-27 Note 1420920000 – 2013 Thread KB Shield Ø L/L1 SW TRQ CN min. / max. TRQ BO min. / max. Qty. Order No. M 18 / 1.5 M 20 / 1.5 M 24 / 1.5 M 25 / 1.5 6.5-9 8-11 14-18 14-18 3.50-7.50 4.00-8.50 9.50-16.50 8.00-13.50 41 / 10 41 / 10 43 / 11 43 / 11 24 24 30 30 9.00 / 30.00 9.00 / 10.00 10.00 / 10.00 10.00 / 10.00 30.00 / 30.00 9.00 / 9.00 10.00 / 10.00 10.00 / 10.00 50 50 50 25 1706920000 1706940000 1706930000 1706950000 PG 7 PG 9 PG 11 PG 13.5 PG 16 PG 16 PG 21 PG 21 PG 29 PG 29 PG 36 4-6.5 6.5-9.5 6.5-9 8-11 10-14 14-18 17-20 17-20 22-26 25-29 27-32 1.50-4.00 2.50-6.00 3.50-7.50 4.00-8.50 6.50-11.50 6.50-11.50 12.50-17.50 12.50-17.50 15.00-21.00 22.00-25.00 24.00-30.50 32 / 5 34 / 6 41 / 10 41 / 10 43 / 11 43 / 11 45 / 11 45 / 11 52 / 13 58 / 13 54 / 9 17 20 24 24 30 30 35 35 40 50 50 6.00 / 20.00 6.00 / 8.00 10.00 / 10.00 10.00 / 10.00 10.00 / 10.00 10.00 / 10.00 10.00 / 15.00 8.00 / 15.00 15.00 / 20.00 20.00 / 20.00 15.00 / 30.00 20.00 / 20.00 6.00 / 6.00 10.00 / 10.00 10.00 / 10.00 10.00 / 10.00 10.00 / 10.00 10.00 / 10.00 8.00 / 8.00 15.00 / 15.00 20.00 / 20.00 15.00 / 15.00 50 50 50 50 25 25 10 10 10 5 10 1713870000 1706860000 1706870000 1706880000 1706890000 1713880000 1706900000 1713890000 1706910000 1713900000 1770410000 Further versions on request C.15 EMC cable glands SW C Brass cable gland for shielding against interference frequencies with a shield attenuation of up to 90 dB. Conical metal cage ensures multiple contacts with the cable shielding. On installation, the cable gland does not have divide into its individual parts, enabling particularly simple installation. Thread Cable entries Cable glands - Brass - 1/EMC L L1 Technical data Material O-ring / Seal insert Temperature range Protection degree Clamp insert Brass, nickel-plated NBR / CR -40 °C...100 °C IP 68 - 10 bar Polyamide Note Length „L“ varies according to cable diameter used Ordering data Typ metric VG M12 - MS 1/EMV VG M16 - MS 1/EMV VG M20 - MS 1/EMV VG M25 - MS 1/EMV VG M32 - MS 1/EMV VG M40 - MS 1/EMV VG M50 - MS 1/EMV VG M63 - MS 1/EMV Note C.16 Thread KB Shield Ø L/L1 SW TRQ CN min. / max. TRQ BO min. / max. Qty. M 12 / 1.5 M 16 / 1.5 M 20 / 1.5 M 25 / 1.5 M 32 / 1.5 M 40 / 1.5 M 50 / 1.5 M 63 / 1.5 3-6.5 4.5-10 6-12 11-17 15-21 19-28 27-38 34-44 3.00-6.50 4.00-10.00 5.00-12.00 10.00-17.00 13.50-21.00 17.00-28.00 25.00-38.00 31.00-44.00 28.5 / 6 37.3 / 7 38.8 / 8 42 / 8 45 / 8 55.1 / 9 62.2 / 9 71.5 / 14 14 20 22 27 34 43 58 64 6.00 / 8.00 5.00 / 7.00 8.00 / 10.00 6.00 / 8.00 6.00 / 10.00 7.00 / 10.00 20.00 / 30.00 23.00 / 28.00 8.00 / 10.00 8.00 / 10.00 12.00 / 15.00 9.00 / 12.00 9.00 / 15.00 10.00 / 15.00 30.00 / 45.00 30.00 / 40.00 50 50 50 25 20 10 10 5 Order No. 1909490000 1909500000 1909510000 1909520000 1909530000 1909540000 1909550000 1909560000 Further versions on request 1420920000 – 2013 Standard cable glands - Stainless steel Cable entries Cable glands - Stainless steel - IP 68 Stainless steel cable glands for standard industrial applications that require a high degree of protection (IP 68). These cable glands – with their resistance to impact and sea water – are also suitable for use in applications under extreme environmental conditions. L C SW1 SW2 Thread L1 Technical data Material O-Ring / Seal insert Temperature range Protection degree Stainless steel 1.4305 (303) NBR / CR -40 °C...100 °C IP 69K, IP 68 - 5 bar (30 min.) Note Ordering data Typ metric VGM12-SS 68 KB 3-6.5 VGM16-SS 68 KB 4-8 VGM20-SS 68 KB 6-12 VGM25-SS 68 KB 10-14 VGM32-SS 68 KB 13-18 VGM40-SS 68 KB 18-25 VGM50-SS 68 KB 22-32 VGM63-SS 68 KB 34-44 PG VG 7-SS 68 KB 3-6.5 VG 9-SS 68 KB 4-8 VG 11-SS 68 KB 5-10 VG 16-SS 68 KB 10-14 VG 21-SS 68 KB 13-18 VG 29-SS 68 KB 18-25 VG 36-SS 68 KB 22-32 VG 42-SS 68 KB 30-38 VG 48-SS 68 KB 34-44 Note 1420920000 – 2013 Thread KB L/L1 SW1/SW2 TRQ CN min. / max. TRQ BO min. / max. Qty. Order No. M 12 / 1.5 M 16 / 1.5 M 20 / 1.5 M 25 / 1.5 M 32 / 1.5 M 40 / 1.5 M 50 / 1.5 M 63 / 1.5 3-6.5 4-8 6-12 10-14 13-18 18-25 22-32 34-44 28 / 6 33 / 7 38 / 8 42 / 8 48 / 9 53 / 9 57 / 9 65 / 14 14 / 14 17 / 19 22 / 22 24 / 27 30 / 36 41 / 46 50 / 55 65 / 70 5.00 / 7.00 8.00 / 10.00 12.00 / 15.00 15.00 / 20.00 28.00 / 35.00 30.00 / 40.00 35.00 / 45.00 45.00 / 55.00 10.00 / 8.00 15.00 / 12.00 22.00 / 16.00 30.00 / 22.00 50.00 / 40.00 60.00 / 45.00 60.00 / 50.00 70.00 / 60.00 50 50 50 25 20 20 12 10 1009840000 1009850000 1009860000 1009870000 1009880000 1009890000 1009900000 1009910000 PG 7 PG 9 PG 11 PG 16 PG 21 PG 29 PG 36 PG 42 PG 48 3-6.5 4-8 5-10 10-14 13-18 18-25 22-32 30-38 34-44 28 / 6 28 / 6 31 / 6 34 / 6.5 39 / 7.5 47 / 8 57 / 9 60 / 12 63 / 14 14 / 14 17 / 17 22 / 22 24 / 24 30 / 30 41 / 41 50 / 50 60 / 60 65 / 65 5.00 / 7.00 8.00 / 10.00 10.00 / 13.00 15.00 / 20.00 28.00 / 35.00 30.00 / 40.00 35.00 / 45.00 40.00 / 50.00 45.00 / 55.00 10.00 / 8.00 15.00 / 12.00 20.00 / 15.00 30.00 / 22.00 50.00 / 40.00 60.00 / 45.00 60.00 / 50.00 70.00 / 55.00 70.00 / 60.00 50 50 50 25 25 20 15 12 10 1009740000 1009750000 1009760000 1009780000 1009790000 1009800000 1009810000 1009820000 1009830000 1.4404 (316L) on request C.17 Cable entries C C.18 1420920000 – 2013 Klippon® Cable Glands – Introduction Cable entries Overview: Klippon® cable glands and selection tool ATEX / IECEx certified cable glands and stopping plugs Cable Gland Type KDSU KDSW KDSX KUB KSG Outer Elastomeric Seal YES YES YES YES YES Inner Elastomeric Seal YES YES YES Compound NO Lead Option NO YES NO NO NO Armour Clamp Universal Steel wire Braided Universal No Certification IP Rating Page No. Ex d / Ex e Ex d / Ex e Ex d / Ex e Ex d Ex d / Ex e IP 68 IP 66, IP 68 IP 66, IP 68 IP 68 IP 66, IP 68 C.30 C.34 C.40 C.44 C.42 C General Health & Safety When Weidmüller cable glands and the accessories are used and installed as prescribed within the data sheet provided, they will not cause any danger or hazard to the health or safety of persons, animals or property. The products should be installed by suitably trained/skilled personnel and in full accordance with the relevant legislative regulations and the accepted code of practice for the industry concerned. Warning Weidmüller cable glands and accessories should not be used within any application other than those specified for each product, unless Weidmüller issue a statement in writing that the product is suitable for the specified application. For further information on each product, we refer you to the specific Assembly Instructions and General Arrangement drawings, which are available on request. Weidmueller takes no responsibility for any damage, unjury or other consequential loss caused where the glands are not installed or used according to our Assembly Instructions. Installation in hazardous area applications If cable glands and accessories are installed in hazardous area applications, international and national standards of the Explosion Protection have to be considered. 1420920000 – 2013/2014 C.19 Cable entries Klippon® KDSU Cable Glands The KDSU type glands provide a universal armour clamp for steel wire, steel tape, screened or braided cables. An electrical bond between the cable armour and the gland is ensured. The gland can also be used to terminate un-armoured cables. In addition, the gland is fitted with two separate seals to seal the outer and inner cable insulation. When choosing the gland with a neoprene sealing a temperature range from -20 °C to +85 °C will be achieved. Whereas the gland with silicone sealing ensures a temperature range from -60 °C to +180 °C. With both sealing materials an IP rating of IP 68 to 25 metres (30 min. at 2.5 bar) is maintained. The KDSU type gland is approved for Flameproof Ex d and Increased Safety Ex e applications. Structure of the part description C Order key Example article description [Type] KDSU Meaning [Type] = Gland type (KDSU) [a] = Entry thread (M20-M75) [b] = Material (B = brass) = Seal material (S = Silicone, N = Neoprene) [c] [d] = Continuity for lead sheath (L = yes, O = no) [e] = Plating (SC = self-coloured, NI = Nickel) = Cable outer sheath (1 = Reduced, 2 = Standard) [f] [ggg] = Gland size (G16-G75) Refer to page C.27 Selection Guide Klippon® Cable Glands to determine the suitable order number Note [a] M20 [b] B [c] S [d] O [e] SC [f] 1 [ggg] G16 B A C D Dimensions Gland Size Entry thread Entry thread Length Max Outer Diameter [ggg] [a] [B] [A] G16 G20S G20 G25 G32 G40 G50S G50 G63S G63 G75S G75 M20 M20 M20 M25 M32 M40 M50 M50 M63 M63 M75 M75 16 16 16 16 16 16 16 16 19 19 19 19 28.0 28.0 33.0 41.4 50.6 60.5 71.5 71.5 88.0 88.0 99.0 99.0 Max Length 78.0 78.0 78.0 90.0 105.0 113.0 125.0 125.0 125.0 125.0 131.0 131.0 Cable Inner Sheath [C] Min 3.4 7.2 9.4 13.5 19.5 23.0 28.1 33.1 39.2 46.7 52.1 58.0 Gland Seal Range Standard [f] = 2 Max Min 8.4 9.0 11.7 11.5 14.0 15.5 20.0 20.3 26.3 26.7 32.2 33.0 38.2 39.4 44.1 45.7 50.1 52.1 56.0 58.4 62.0 64.8 68.0 71.1 Dimensions in mm Cable Outer Sheath [D] Max 13.5 16.0 21.1 27.4 34.0 40.6 46.7 53.2 59.5 65.8 72.2 78.0 Min 6.7 9.4 12.0 16.8 23.2 28.6 34.8 41.1 47.5 53.8 60.2 66.5 Reduced [f] = 1 Max 10.3 12.5 17.6 23.9 30.5 36.2 42.4 48.5 54.8 61.2 68.0 73.4 Armour Acceptance Range Shroud Size 0.15 - 1.25 0.15 - 1.25 0.15 - 1.25 0.15 - 1.60 0.15 - 2.00 0.20 - 2.00 0.30 - 2.50 0.30 - 2.50 0.30 - 2.50 0.30 - 2.50 0.30 - 2.50 0.30 - 2.50 L24 L24 EL30 EL38 EL46 EL55 EL65 EL65 EL80 EL80 EL90 EL90 Important Notes • The gland size does not necessarily equate to the entry thread size. • In some cases several gland sizes can be chosen due to overlaping inner as well as outer cable diameters. Due to the wide range of armoured cables available, it is necessary to select the correct clamping range. This is achieved by taking the inner and outer clamping range values to determine the best fit (as close as possible to the Min/Max values average). • All cable glands have a 1.5 mm pitch. • For Flameproof Ex d applications the female thread into which the gland is to be fitted must achieve an engagement of at least 5 full threads in compliance with clause 5.3 of EN/IEC 60079-1. • Where KDSU glands are fitted into non-metallic Increased Safety Ex e enclosures they must be included within the earth circuit of the system. • Fully assembly instructions are supplied with the glands. The instructions must be read prior to installation and adhered to in full. • When the gland is used to terminate un-armoured cables, the gland is suitable only for fixed installation. C.20 1420920000 – 2013/2014 Klippon® KDSW Cable Glands Cable entries The KDSW glands provide an armour clamp for steel wire, steel tape and lead sheathed cables. An electrical bond between the cable armour and the gland is ensured. In addition, the gland is fitted with two separate sealings to seal the outer and inner cable insulation. When choosing the gland with a neoprene sealing a temperature range from -20 °C to +85 °C will be achieved, whereas the gland with silicone sealing ensures a temperature range from -60 °C to +180 °C. With both sealing materials an IP rating of IP 66 and IP 68 to 25 metres (30 min at 2.5 bar) is maintained. The KDSW gland is approved for Flameproof Ex d and Increased Safety Ex e applications. Structure of the part description Order key Example article description [Type] KDSW Meaning [Type] = Gland type (KDSW) [a] = Entry thread (M20-M75) [b] = Material (B = brass) = Seal material (S = Silicone, N = Neoprene) [c] [d] = Continuity for lead sheath (L = yes, O = no) = Plating (SC = self-coloured, NI = Nickel) [e] [f] = Cable outer sheath (1 = Reduced, 2 = Standard) [ggg] = Gland size (G16-G75) Refer to page C.27 Selection Guide Klippon® Cable Glands to determine the suitable order number Note [a] M20 [b] B [c] S [d] L [e] SC [f] 1 [ggg] G16 C B A D C Dimensions Gland Size Entry thread Entry thread Length Max Outer Diameter [ggg] [a] [B] [A] G16 G20S G20 G25 G32 G40 G50S G50 G63S G63 G75S G75 M20 M20 M20 M25 M32 M40 M50 M50 M63 M63 M75 M75 16 16 16 16 16 16 16 16 19 19 19 19 26.5 26.5 33.0 41.4 50.6 60.5 71.5 71.5 88.0 88.0 99.0 99.0 Max Length 58.0 58.0 58.0 58.0 65.0 72.0 73.0 73.0 76.0 76.0 82.0 82.0 Cable Inner Sheath [C] Min 4.0 8.0 6.7 13.0 19.0 25.0 31.5 36.5 42.5 49.5 54.5 60.5 Gland Seal Range Standard [f] = 2 Max Min 8.4 8.4 11.7 11.5 14.0 15.5 20.0 20.3 26.3 26.7 32.2 33.0 38.2 39.4 44.1 45.7 50.1 52.1 56.0 58.4 62.0 64.8 68.0 71.1 Dimensions in mm Cable Outer Sheath [D] Max 13.5 16.0 21.1 27.4 34.0 40.6 46.7 53.2 59.5 65.8 72.2 78.0 Min 4.9 9.4 12.0 16.8 23.2 28.6 34.8 41.1 47.5 53.8 60.2 66.5 Reduced [f] = 1 Max 10.0 12.5 17.6 23.9 30.5 36.2 42.4 48.5 54.8 61.2 68.0 73.4 Armour Acceptance Range Shroud Size 0.90 0.90 – 1.25 0.90 – 1.25 1.25 – 1.60 1.60 – 2.00 1.60 – 2.00 2.00 – 2.50 2.00 – 2.50 2.50 2.50 2.50 2.5 L24 L24 L30 L38 L46 L55 L65 L65 L80 L80 L90 L90 Important Notes • The gland size does not necessarily equate to the entry thread size. • In some cases several gland sizes can be chosen due to overlaping inner as well as outer cable diameters. Due to the wide range of armoured cables available, it is necessary to select the correct clamping range. This is achieved by taking the inner and outer clamping range values to determine the best fit (as close as possible to the Min/Max values average). • All cable glands have a 1.5 mm pitch. • For Flameproof Ex d applications the female thread into which the gland is to be fitted must achieve an engagement of at least 5 full threads in compliance with clause 5.3 of EN/IEC 60079-1. • Where KDSW glands are fitted into non-metallic Increased Safety Ex e enclosures they must be included within the earth circuit of the system. • Fully assembly instructions are supplied with the glands. The instructions must be read prior to installation and adhered to in full. • When the gland is used to terminate un-armoured cables, the gland is suitable only for fixed installation. • KDSW gland size G20 with silicone seal , the silicone inner seal only seals to a minimum of 11 mm and NOT 6.7 mm. 1420920000 – 2013/2014 C.21 Cable entries Klippon® KDSX Cable Glands The KDSX glands provide an armour clamp for braided cables. An electrical bond between the cable armour and the gland is ensured. In addition, the gland is fitted with two separate sealings to seal the outer and inner cable insulation. The gland maintains a temperature range from -60 °C to +180 °C. With both sealing materials an IP rating of IP 66 and IP 68 to 25 metres (30 min at 2.5 bar) is maintained. The KDSX gland is approved for Flameproof Ex d and Increased Safety Ex e applications. Structure of the part description C Order key Example article description [Type] KDSX Meaning [Type] = Gland type (KDSX) [a] = Entry thread (M20-M75) [b] = Material (B = brass) = Seal material (S = Silicone) [c] [d] = Continuity for lead sheath (L = yes, O = no) [e] = Plating (SC = self-coloured, NI = Nickel) = Cable outer sheath (1 = Reduced, 2 = Standard) [f] [ggg] = Gland size (G16-G75) Refer to page C.27 Selection Guide Klippon® Cable Glands to determine the suitable order number Note [a] M20 [b] B [c] S [d] O [e] SC [f] 1 [ggg] G16 B A D C Dimensions Gland Size Entry thread Entry thread Length Max Outer Diameter [ggg] [a] [B] [A] G16 G20S G20 G25 G32 G40 G50S G50 G63S G63 G75S G75 M20 M20 M20 M25 M32 M40 M50 M50 M63 M63 M75 M75 16 16 16 16 16 16 16 16 19 19 19 19 26.5 26.5 33.0 41.4 50.6 60.5 71.5 71.5 88.0 88.0 99.0 99.0 Max Length 58.0 58.0 58.0 58.0 65.0 72.0 73.0 73.0 76.0 76.0 82.0 82.0 Cable Inner Sheath [C] Min 4.0 8.0 6.7 13.0 19.0 25.0 31.5 36.5 42.5 49.5 54.5 60.5 Gland Seal Range Standard [f] = 2 Max Min 8.4 8.4 11.7 11.5 14.0 15.5 20.0 20.3 26.3 26.7 32.2 33.0 38.2 39.4 44.1 45.7 50.1 52.1 56.0 58.4 62.0 64.8 68.0 71.1 Dimensions in mm Cable Outer Sheath [D] Max 13.5 16.0 21.1 27.4 34.0 40.6 46.7 53.2 59.5 65.8 72.2 78.0 Min 4.9 9.4 12.0 16.8 23.2 28.6 34.8 41.1 47.5 53.8 60.2 66.5 Reduced [f] = 1 Max 10.0 12.5 17.6 23.9 30.5 36.2 42.4 48.5 54.8 61.2 68.0 73.4 Armour Acceptance Range Shroud Size 0.15 – 0.35 0.15 – 0.35 0.15 – 0.50 0.15 – 0.50 0.15 – 0.55 0.20 – 0.60 0.20 – 0.60 0.30 – 0.80 0.30 – 0.80 0.30 – 0.80 0.30 – 1.00 0.30 – 1.00 L24 L24 L30 L38 L46 L55 L65 L65 L80 L80 L90 L90 Important Notes • The gland size does not necessarily equate to the entry thread size. • In some cases several gland sizes can be chosen due to overlaping inner as well as outer cable diameters. Due to the wide range of armoured cables available, it is necessary to select the correct clamping range. This is achieved by taking the inner and outer clamping range values to determine the best fit (as close as possible to the Min/Max values average). • All cable glands have a 1.5 mm pitch. • For Flameproof Ex d applications the female thread into which the gland is to be fitted must achieve an engagement of at least 5 full threads in compliance with clause 5.3 of EN/IEC 60079-1. • Where KDSX glands are fitted into non-metallic Increased Safety Ex e enclosures they must be included within the earth circuit of the system. • Fully assembly instructions are supplied with the glands. The instructions must be read prior to installation and adhered to in full. • When the gland is used to terminate un-armoured cables, the gland is suitable only for fixed installation. • KDSX gland size G20 with silicone seal , the silicone inner seal only seals to a minimum of 11 mm and NOT 6.7 mm. C.22 1420920000 – 2013/2014 Klippon® KSG Cable Glands Cable entries The KSG gland is designed to terminate un-armoured cables. When choosing the gland with a neoprene sealing a temperature range from -20 °C to +85 °C will be achieved, whereas the gland with silicone sealing ensures a temperature range from -60 °C to +180 °C. With both sealing materials an IP rating of IP 66 and IP 68 to 25 metres (30 min. at 2.5 bar) is maintained. The KSG type gland is approved for Flameproof Ex d and Increased Safety Ex e applications. Structure of the part description Order key Example article description [Type] KSG Meaning [Type] = Gland type (KSG) [a] = Entry thread (M20-M90) [b] = Material (B = brass) = Seal material (S = Silicone, N = Neoprene) [c] [d] = Continuity for lead sheath (L = yes, O = no) [e] = Plating (SC = self-coloured, NI = Nickel) = Cable outer sheath (2 = Standard) [f] [ggg] = Gland size (G16-G90) Refer to page C.27 Selection Guide Klippon® Cable Glands to determine the suitable order number Note [a] M20 [b] B [c] S [d] O [e] SC [f] 2 [ggg] G16 C B A D Dimensions Gland Size Entry thread Entry thread Length Max Outer Diameter [ggg] [a] [B] [A] G16 G20S G20 G25 G32 G40 G50S G50 G63S G63 G75S G75 G85 G90 M20 M20 M20 M25 M32 M40 M50 M50 M63 M63 M75 M75 M85 M90 16 16 16 16 16 16 16 16 19 19 19 19 25 25 28.0 28.0 33.0 41.4 50.6 60.5 71.5 71.5 88.0 88.0 99.0 99.0 115.2 125.7 Max Length 33.0 33.0 33.0 33.0 33.0 37.0 37.0 37.0 37.0 37.0 37.0 37.0 50 50 Dimensions in mm Min 4.0 7.2 9.6 13.5 19.5 23.0 28.2 33.2 39.3 46.7 52.3 58.1 69.1 74.1 Gland Seal Range Cable Outer Sheath [D] Standard [f] = 2 Shroud Size Max 8.4 11.7 14.0 20.0 26.3 32.2 38.2 44.1 50.1 56.0 62.0 69.0 78.0 84.0 L24 L24 L30 L38 L46 L55 L65 L65 L80 L80 L90 L90 L104 L114 Important Notes • The gland size does not necessarily equate to the entry thread size. • In some cases several gland sizes can be chosen due to overlaping inner as well as outer cable diameters. Due to the wide range of armoured cables available, it is necessary to select the correct clamping range. This is achieved by taking the inner and outer clamping range values to determine the best fit (as close as possible to the Min/Max values average). • All cable glands have a 1.5 mm pitch. • For Flameproof Ex d applications the female thread into which the gland is to be fitted must achieve an engagement of at least 5 full threads in compliance with clause 5.3 of EN/IEC 60079-1. • Where KSG glands are fitted into non-metallic Increased Safety Ex e enclosures they must be included within the earth circuit of the system. • Fully assembly instructions are supplied with the glands. The instructions must be read prior to installation and adhered to in full. • When the gland is used to terminate un-armoured cables, the gland is suitable only for fixed installation. 1420920000 – 2013/2014 C.23 Cable entries Klippon® KUB Cable Glands The KUB gland provide an armour clamp for steel tape, steel wire and braided cables. An electrical bond between the cable armour and the gland is ensured. The gland can also be used to terminate unarmoured cables. Additionally, the gland provides a single pull resistant seal on the outer sheath of any cable. After clamping the cable armour onto the cone, the cable has to be filled with the provided compound to seal the free spaces between the single conductors. The gland maintains a temperature range from -60 °C to +85 °C. When filled, the gland fulfills an IP rating of IP 68 to 100 metres (30 Min. at 10 bar). The KUB gland is only suitable for Ex d applications. Structure of the part description C Order key Example article description [Type] KUB Meaning [Type] = Gland type (KUB) [a] = Entry thread (M20-M75) [b] = Material (B = brass) = Seal material (S = Silicone) [c] [d] = Continuity for lead sheath (L = yes, O = no) [e] = Plating (SC = self-coloured, NI = Nickel) = Cable outer sheath (1 = Reduced, 2 = Standard) [f] [ggg] = Gland size (G16-G75) Refer to page C.27 Selection Guide Klippon® Cable Glands to determine the suitable order number Note [a] M20 [b] B [c] S [d] O [e] SC [f] 1 [ggg] G16 B A D C Dimensions Gland Size Entry thread Entry thread Length Max Outer Diameter [ggg] [a] [B] [A] G16 G20S G20 G25 G32 G40 G50S G50 G63S G63 G75S G75 M20 M20 M20 M25 M32 M40 M50 M50 M63 M63 M75 M75 16 16 16 16 16 16 16 16 19 19 19 19 28.0 28.0 33.0 41.4 50.6 60.5 71.5 71.5 88.0 88.0 99.0 99.0 Max Length 72.0 72.0 73.0 83.0 103.0 105.0 115.0 115.0 115.0 115.0 122.0 122.0 Cable Inner Sheath [C] X 7 8 14 25 50 80 100 100 120 120 140 140 Y 9.0 10.4 12.5 17.8 23.5 28.8 34.2 39.4 44.8 50.0 55.4 60.8 Gland Seal Range Z 11.7 11.7 14.0 20.0 26.3 32.2 38.2 44.1 50.1 56.0 62.0 68.0 Dimensions in mm Cable Outer Sheath [D] Standard [f] = 2 Min Max 9.0 13.5 11.5 16.0 15.5 21.1 20.3 27.4 26.7 34.0 33.0 40.6 39.4 46.7 45.7 53.2 52.1 59.5 58.4 65.8 64.8 72.2 71.1 78.0 Min 6.7 9.4 12.0 16.8 23.2 28.6 34.8 41.1 47.5 53.8 60.2 66.5 Reduced [f] = 1 Max 10.3 12.5 17.6 23.9 30.5 36.2 42.4 48.5 54.8 61.2 68.0 73.4 Armour Acceptance Range Shroud Size 0.15 - 1.25 0.15 - 1.25 0.15 - 1.25 0.15 - 1.60 0.15 - 2.00 0.20 - 2.00 0.30 - 2.50 0.30 - 2.50 0.30 - 2.50 0.30 - 2.50 0.30 - 2.50 0.30 - 2.50 L24 L24 EL30 EL38 EL46 EL55 EL65 EL65 EL80 EL80 EL90 EL90 Important Notes • The gland size does not necessarily equate to the entry thread size. • In some cases several gland sizes can be chosen due to overlaping inner as well as outer cable diameters. Due to the wide range of armoured cables available, it is necessary to select the correct clamping range. This is achieved by taking the inner and outer clamping range values to determine the best fit (as close as possible to the Min/Max values average). • X = Maximum numbers of cores • Y = Maximum over cores • Z = Maximum inner sheath • All cable glands have a 1.5 mm pitch. • For Flameproof Ex d applications the female thread into which the gland is to be fitted must achieve an engagement of at least 5 full threads in compliance with clause 5.3 of EN/IEC 60079-1. • Where KUB glands are fitted into non-metallic Increased Safety Ex e enclosures they must be included within the earth circuit of the system • Fully assembly instructions are supplied with the glands. The instructions must be read prior to installation and adhered to in full. • When the gland is used to terminate un-armoured cables, the gland is suitable only for fixed installation C.24 1420920000 – 2013/2014 Klippon® Cable Glands Cable entries Selection Guide Klippon® Cable Glands Purpose: Generation of the article description By selecting the suitable cable gland different factors have to be considered, such as •The environment of the application •The conditions inside the enclosure •The construction of the cable By using the Selection Guide Klippon® Cable Glands the article description will be generated following the step by step process to create the 7 character order key. From this the order number can be identified. C The order key consists out of the following attributes: Order key Example Article Description [Type] KDSU Meaning [Type] [a] [b] [c] [d] [e] [f] [ggg] [a] M20 = = = = = = = = [b] B [c] S [d] O [e] SC [f] 1 [ggg] G16 Gland type (KDSU, KDSW, KDSX, KSG, KUB) Entry thread (M20-M75) Material (B = brass) Seal material (S=Silicone, N=Neoprene) Continuity for lead sheath (L = yes, O = no) Plating (SC = self-coloured, NI = nickel-plated Cable outer sheath (1 = Reduced, 2 = Standard) Gland size (G16-G75) Application example Within an Ex d application on an Off-Shore platform a suitable cable gland for the termination into an enclosure is required. Following details about the application are given: •The enclosure will be used for the control of a motor circuit breaker •The enclosure has a volume of 1.3 dm3 and is installed outdoor. •The application is in the field, a place in which an explosive atmosphere is likely to occur in normal operation, occasionally (Zone 1) •The surrounding atmosphere of the enclosure consists Ethylene (gas group IIB) •The enclosure operates in a temperature range of -25 °C to +45 °C •The armour of the cable is unknown, no lead sheathed cable •The cable outer sheath diameter is 10 mm •The cable inner sheath diameter is 8 mm Based on the information in the above shown example case the article description will be determined on the following pages. 1420920000 – 2013/2014 C.25 Cable entries Klippon® Cable Glands 1. Selection of the cable gland type [type] and continuity for lead sheath [d] Order key Example Article Description C [Type] [a] [b] [c] [d] [e] [f] [ggg] 1a) Selection of the cable gland type in regard to the ignition protection type [Type] KDSU KDSW KDSX KSG KUB Ignition Protecion Type Ex d / Ex e Ex d / Ex e Ex d / Ex e Ex d / Ex e Ex d Because it is an Ex d application all cable gland types (marked in blue) can come into consideration. For Ex d applications the following questionnaire according to the IEC 60079-14 standard has to be passed to find out if a barrier gland ([Type]=KUB) or if a cable gland with a sealing ring ([Type]=KDSU,KDSW,KDSX) has to be used. Application example Start Does the enclosure contain an internal source of ignition? YES Does the hazardous gas require IIC apparatus? YES NO YES Use a barrier gland YES NO Is the volume of the enclosure greater than 2 dm3? Is the area of installation zone 1? NO Use a suitable flameproof cable entry device with a sealing ring NO By passing this questionnaire with the given information of the example case the orange marked way has to be followed and the result is that a cable gland with sealing ring has to be used. Consequently the blue marked cable gland types below can come into consideration. Gland type KDSU KDSW KDSX KSG KUB C.26 Type of sealing Sealing ring Sealing ring Sealing ring Sealing ring Compound 1420920000 – 2013/2014 Cable entries Klippon® Cable Glands 1b) Selection of the cable gland type in regard to the continuity for lead sheath [Type] KDSU KDSW KDSX KSG KUB [d] O L/O O O O Continuity for lead sheath No Yes No No No C In the example case a cable without lead sheath is to be terminated, therefore the option to clamp a lead sheathed cable is not needed. Consequently is [d] = O All four gland types marked in blue can be used. 1c) Selection of the cable gland type in regard to the type of armour [Type] KDSU KDSW KDSX KSG KUB Armour Universal Steel wire, steel tape Braided No armour Universal Because the type of armour of the cable is unknown, the cable gland type KDSU has to be selected. Consequently is [Type] = KDSU The generated information has to be filled into the order key below: Order key Example Article Description 1420920000 – 2013/2014 [Type] KDSU [a] [b] [c] [d] O [e] [f] [ggg] C.27 Cable entries Klippon® Cable Glands 2. Selection of the material [b], the sealing material [c] and the plating [e] of the cable gland Order key Example Article Description C [Type] KDSU [a] [b] [c] [d] O [e] [f] [ggg] 2a) Selection of the material [b] All cable gland types are made from brass “b”. Other materials can also be provided upon request. Consequently is [b] = B 2b) Selection of the sealing material [c] based on the required temperature range The cable glands can be ordered with either a neoprene seal “N” or a silicone seal “S”. Glands with a neoprene seal can be used in a temperature range from -20 °C to +85 °C, whereas glands with silicone seal maintain a temperature range from -60 °C to +180 °C. (KUB glands are certified to a temperature of -60 °C to +85 °C). [Type] KDSU KDSW KDSX KSG KUB [c] N,S N,S S N,S N Seal material Neoprene, Silicone Neoprene (with continuity for lead sheath), Silicone Silicone Neoprene, Silicone Silicone (-60 °C to +85 °C) Because the enclosure in the example case operates in a temperature range of -25 °C to +45 °C, a cable gland with a silicone seal has to be used. Consequently is [c] = „S“ (Silicone) 2c) Selection of the plating [e] All cable glands can be provided either with nickel plated surface “NI” or with self-coloured surface “SC”. In the example case the enclosure is used outdoor, therefore it can come into contact with water in form of rain, so that a cable gland with nickel plated surface as protection against corrosion and wear has to be selected. Consequently is [e] = „NI“ The generated information has to be filled into the order key below: Order key Example Article Description [Type] KDSU [a] [b] B [c] S [d] O [e] NI [f] [ggg] [e] NI [f] [ggg] 3. S election of the entry thread [a], the cable outer sheath variant [f] and the gland size [ggg] Order key Example Article Description [Type] KDSU [a] [b] B [c] S [d] O The suitable gland size [ggg] will be selected based on the inner and outer sheath diameters of the cable. Thereby the entry thread size [a] and the cable outer sheath variant [f] result. C.28 1420920000 – 2013/2014 Cable entries Klippon® Cable Glands In the example case the following diameters are given: Cable Outer Sheath: 10 mm (By looking into the below shown dimensions chart of the KDSU the orange marked clamping ranges (Cable Outer Sheath [D]) can be selected). Cable Inner Sheath: 8 mm (By looking into the below shown dimensions chart of the KDSU the orange marked clamping ranges (Cable Inner Sheath [C]) can be selected). C Dimensions Gland Seal Range Gland Size [ggg] G16 G20S G20 G25 G32 G40 G50S G50 G63S G63 G75S G75 Entry thread M20 M20 M20 M25 M32 M40 M50 M50 M63 M63 M75 M75 Entry thread Length [B] 16 16 16 16 16 16 16 16 19 19 19 19 Max Outer Diameter Max Length [A] 28.0 28.0 33.0 41.4 50.6 60.5 71.5 71.5 88.0 88.0 99.0 99.0 Cable Inner Sheath [C] Min 3.4 7.2 9.4 13.5 19.5 23.0 28.1 33.1 39.2 46.7 52.1 58.0 78.0 78.0 78.0 90.0 105.0 113.0 125.0 125.0 125.0 125.0 131.0 131.0 Cable Outer Sheath [D] Standard [f]=2 Max Min 8.4 9.0 11.7 11.5 14.0 15.5 20.0 20.3 26.3 26.7 32.2 33.0 38.2 39.4 44.1 45.7 50.1 52.1 56.0 58.4 62.0 64.8 68.0 71.1 All dimensions in mm Max 13.5 16.0 21.1 27.4 34.0 40.6 46.7 53.2 59.5 65.8 72.2 78.0 Min 6.7 9.4 12.0 16.8 23.2 28.6 34.8 41.1 47.5 53.8 60.2 66.5 Reduced [f]=1 Max 10.3 12.5 17.6 23.9 30.5 36.2 42.4 48.5 54.8 61.2 68.0 73.4 Armour Acceptance Range Shroud Size 0.15 - 1.25 0.15 - 1.25 0.15 - 1.25 0.15 - 1.60 0.15 - 2.00 0.20 - 2.00 0.30 - 2.50 0.30 - 2.50 0.30 - 2.50 0.30 - 2.50 0.30 - 2.50 0.30 - 2.50 L24 L24 EL30 EL38 EL46 EL55 EL65 EL65 EL80 EL80 EL90 EL90 By the selection of the inner [C] resp. outer [D] clamping range, a range should be used where the diameter of the cable outer and inner sheath are as near as possible to the average of the Min/Max Values. In doing so, the reduced cable outer sheath with the gland size G20S and the entry thread of M20 has to be selected. Consequently is [f]=1 [ggg]=G20S [a]=M20 The generated information has to be filled into the order key below: [Type] KDSU Order key Article description [a] M20 [b] B [c] S [d] O [e] NI [f] 1 [ggg] G20S Resulting from the complete article description the relating order number (brown marked) can be determined. Extract from table KDSU “Nickel-plated brass gland with silicone sealing” on page C.33 Order No. 0930001221 0930001222 0930011223 0930011224 0930021221 … Description KDSU M20 BS O NI 1 G16 KDSU M20 BS O NI 2 G16 KDSU M20 BS O NI 1 G20S KDSU M20 BS O NI 2 G20S KDSU M20 BS O NI 1 G20 … 1420920000 – 2013/2014 [Type] KDSU KDSU KDSU KDSU KDSU … [a] M20 M20 M20 M20 M20 … [b] B B B B B … [c] S S S S S … [d] O O O O O … [e] NI NI NI NI NI … [f] 1 2 1 2 1 … [ggg] G16 G16 G20S G20S G20 … Qty. 20 20 20 20 20 … C.29 Cable glands for Ex applications - Brass Cable entries Klippon® cable glands - Brass - Ex e, Ex d, IP 68 for armoured and non-armoured cables All-purpose cable gland for cables and lines with single-wire armouring, metal-foil armouring and braided armouring. Non-armoured cables and lines can also be connected. L L1 SW C D2 D1 Thread Technical data Material O-Ring / Seal insert Temperature range Degree of protection Water depth Type of armouring Approval Brass NBR / CR -20 °C...85 °C IP 68 - 2.5 bar 25 m (30 Min.) Single-wire armouring, Metal foil armouring, Braided armouring ATEX ll 2 GD, Ex d llC / Ex e ll / Ex tD A21 IP68, IECEx Ex d IIC / Ex e ll Note Ordering data Typ metric, brass KDSU M20 BN O SC 1 G16 KDSU M20 BN O SC 2 G16 KDSU M20 BN O SC 1 G20S KDSU M20 BN O SC 2 G20S KDSU M20 BN O SC 1 G20 KDSU M20 BN O SC 2 G20 KDSU M25 BN O SC 1 G25 KDSU M25 BN O SC 2 G25 KDSU M32 BN O SC 1 G32 KDSU M32 BN O SC 2 G32 KDSU M40 BN O SC 1 G40 KDSU M40 BN O SC 2 G40 KDSU M50 BN O SC 1 G50S KDSU M50 BN O SC 2 G50S KDSU M50 BN O SC 1 G50 KDSU M50 BN O SC 2 G50 KDSU M63 BN O SC 1 G63S KDSU M63 BN O SC 2 G63S KDSU M63 BN O SC 1 G63 KDSU M63 BN O SC 2 G63 KDSU M75 BN O SC 1 G75S KDSU M75 BN O SC 2 G75S KDSU M75 BN O SC 1 G75 KDSU M75 BN O SC 2 G75 Note C.30 Thread D1 outer cable Ø D2 inner cable Ø Cable armour L/L1 SW MODR SUHB Qty. M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 25 / 1.5 M 25 / 1.5 M 32 / 1.5 M 32 / 1.5 M 40 / 1.5 M 40 / 1.5 M 50 / 1.5 M 50 / 1.5 M 50 / 1.5 M 50 / 1.5 M 63 / 1.5 M 63 / 1.5 M 63 / 1.5 M 63 / 1.5 M 75 / 1.5 M 75 / 1.5 M 75 / 1.5 M 75 / 1.5 6.70-10.30 9.00-13.50 9.40-12.50 11.50-16.00 12.00-17.60 15.50-21.10 16.80-23.90 20.30-27.40 23.20-30.50 26.70-34.00 28.60-36.20 33.00-40.60 34.80-42.40 39.40-46.70 41.10-48.50 45.70-53.20 47.50-54.80 52.10-59.50 53.80-61.20 58.40-65.80 60.20-68.00 64.80-72.20 66.50-73.40 71.10-78.00 3.40-8.40 3.40-8.40 7.20-11.70 7.20-11.70 9.40-14.00 9.40-14.00 13.50-20.00 13.50-20.00 19.50-26.30 19.50-26.30 23.00-32.20 23.00-32.20 28.10-38.20 28.10-38.20 33.10-44.10 33.10-44.10 39.20-50.10 39.20-50.10 46.70-56.00 46.70-56.00 52.10-62.00 52.10-62.00 58.00-68.00 58.00-68.00 0.15-1.25 0.15-1.25 0.15-1.25 0.15-1.25 0.15-1.25 0.15-1.25 0.15-1.6 0.15-1.6 0.15-2 0.15-2 0.2-2 0.2-2 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 78 / 16 78 / 16 78 / 16 78 / 16 78 / 16 78 / 16 90 / 16 90 / 16 105 / 16 105 / 16 113 / 16 113 / 16 125 / 16 125 / 16 125 / 16 125 / 16 125 / 19 125 / 19 125 / 19 125 / 19 131 / 19 131 / 19 131 / 19 131 / 19 24 24 24 24 30 30 38 38 46 46 55 55 65 65 65 65 80 80 80 80 90 90 90 90 32.5 32.5 32.5 32.5 32.5 32.5 50 50 80 80 80 80 100 100 100 100 160 160 160 160 200 200 200 200 L24 L24 L24 L24 EL30 EL30 EL38 EL38 EL46 EL46 EL55 EL55 EL65 EL65 EL65 EL65 EL80 EL80 EL80 EL80 EL90 EL90 EL90 EL90 20 20 20 20 20 20 20 20 10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 Order No. 1076120000 1909260000 1076130000 1909290000 1076140000 1909300000 1076150000 1909310000 1076160000 1909320000 1076170000 1909330000 1076180000 1909340000 1076190000 1909350000 1076200000 1909360000 1076210000 1909370000 1076220000 1076230000 1076240000 1076260000 • All cable glands have a thread pitch of 1.5 mm. • In the case of Ex d applications, the inner threads used for cable glands must meet the requirements of section 5.3 of EN/IEC 60079-1. In the screwed in position, at least 5 threads must be engaged. • If the cable glands are installed in non-metallic Ex e connection equipment, these must be connected to the protective earth of the system. • The connection cable must be laid securely and inflexibly to rule out tensile stress. 1420920000 – 2013 Cable glands for Ex applications - Brass Cable entries Klippon® cable glands - Brass - Ex e, Ex d, IP 68 for armoured and non-armoured cables All-purpose cable gland for cables and lines with single-wire armouring, metal-foil armouring and braided armouring. Non-armoured cables and lines can also be connected. L SW L1 C D2 D1 Thread Technical data Material O-Ring / Seal insert Temperature range Degree of protection Water depth Type of armouring Approval Brass, nickel-plated NBR / CR -20 °C...85 °C IP 68 - 2.5 bar 25 m (30 Min.) Single-wire armouring, Metal foil armouring, Braided armouring ATEX ll 2 GD, Ex d llC / Ex e ll / Ex tD A21 IP68, IECEx Ex d IIC / Ex e ll Note Ordering data Typ metric, nickel-plated brass KDSU M20 BN O NI 1 G16 KDSU M20 BN O NI 2 G16 KDSU M20 BN O NI 1 G20S KDSU M20 BN O NI 2 G20S KDSU M20 BN O NI 1 G20 KDSU M20 BN O NI 2 G20 KDSU M25 BN O NI 1 G25 KDSU M25 BN O NI 2 G25 KDSU M32 BN O NI 1 G32 KDSU M32 BN O NI 2 G32 KDSU M40 BN O NI 1 G40 KDSU M40 BN O NI 2 G40 KDSU M50 BN O NI 1 G50 KDSU M50 BN O NI 2 G50 KDSU M50 BN O NI 1 G50S KDSU M50 BN O NI 2 G50S KDSU M63 BN O NI 1 G63S KDSU M63 BN O NI 2 G63S KDSU M63 BN O NI 1 G63 KDSU M63 BN O NI 2 G63 KDSU M75 BN O NI 1 G75S KDSU M75 BN O NI 2 G75S KDSU M75 BN O NI 1 G75 KDSU M75 BN O NI 2 G75 Note 1420920000 – 2013 Thread D1 outer cable Ø D2 inner cable Ø Cable armour L/L1 SW MODR SUHB Qty. M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 25 / 1.5 M 25 / 1.5 M 32 / 1.5 M 32 / 1.5 M 40 / 1.5 M 40 / 1.5 M 50 / 1.5 M 50 / 1.5 M 50 / 1.5 M 50 / 1.5 M 63 / 1.5 M 63 / 1.5 M 50 / 1.5 M 63 / 1.5 M 75 / 1.5 M 75 / 1.5 M 75 / 1.5 M 75 / 1.5 6.70-10.30 9.00-13.50 9.40-12.50 11.50-16.00 12.00-17.60 15.50-21.10 16.80-23.90 20.30-27.40 23.20-30.50 26.70-34.00 28.60-36.20 33.00-40.60 41.10-48.50 45.70-53.20 34.80-42.40 39.40-46.70 47.50-54.80 52.10-59.50 53.80-61.20 58.40-65.80 60.20-68.00 64.80-72.20 66.50-73.40 71.10-78.00 3.40-8.40 3.40-8.40 7.20-11.70 7.20-11.70 9.40-14.00 9.40-14.00 13.50-20.00 13.50-20.00 19.50-26.30 19.50-26.30 23.00-32.20 23.00-32.20 33.10-44.10 33.10-44.10 28.10-38.20 28.10-38.20 39.20-50.10 39.20-50.10 46.70-56.00 46.70-56.00 52.10-62.00 52.10-62.00 58.00-68.00 58.00-68.00 0.15-1.25 0.15-1.25 0.15-1.25 0.15-1.25 0.15-1.25 0.15-1.25 0.15-1.6 0.15-1.6 0.15-2 0.15-2 0.2-2 0.2-2 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 78 / 16 78 / 16 78 / 16 78 / 16 78 / 16 78 / 16 90 / 16 90 / 16 105 / 16 105 / 16 113 / 16 113 / 16 125 / 16 125 / 16 125 / 16 125 / 16 125 / 19 125 / 19 125 / 16 125 / 19 131 / 19 131 / 19 131 / 19 131 / 19 24 24 24 24 30 30 38 38 46 46 55 55 65 65 65 65 80 80 80 80 90 90 90 90 32.5 32.5 32.5 32.5 32.5 32.5 50 50 80 80 80 80 100 100 100 100 160 160 160 160 200 200 200 200 L24 L24 L24 L24 EL30 EL30 EL38 EL38 EL46 EL46 EL55 EL55 EL65 EL65 EL65 EL65 EL80 EL80 EL80 EL80 EL90 EL90 EL90 EL90 20 20 20 20 20 20 20 20 10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 Order No. 1083280000 1911380000 1083290000 1911390000 1083320000 1911400000 1083330000 1911420000 1083340000 1911430000 1083350000 1911440000 1083370000 1911460000 1083360000 1911450000 1083380000 1911480000 1083390000 1911490000 1083400000 1083410000 1083420000 1083430000 • All cable glands have a thread pitch of 1.5 mm. • In the case of Ex d applications, the inner threads used for cable glands must meet the requirements of section 5.3 of EN/IEC 60079-1. In the screwed in position, at least 5 threads must be engaged. • If the cable glands are installed in non-metallic Ex e connection equipment, these must be connected to the protective earth of the system. • The connection cable must be laid securely and inflexibly to rule out tensile stress. C.31 Cable glands for Ex applications - Brass Cable entries Klippon® cable glands - Brass - Ex e, Ex d, IP 68 for armoured and non-armoured cables All-purpose cable gland for cables and lines with single-wire armouring, metal-foil armouring and braided armouring. Non-armoured cables and lines can also be connected. L L1 SW C D2 D1 Thread Technical data Material O-Ring / Seal insert Temperature range Degree of protection Water depth Type of armouring Approval Brass Silicone / Silicone -60 °C...180 °C IP 68 - 2.5 bar 25 m (30 Min.) Single-wire armouring, Metal foil armouring, Braided armouring ATEX ll 2 GD, Ex d llC / Ex e ll / Ex tD A21 IP68, IECEx Ex d IIC / Ex e ll Note Ordering data Typ metric, brass KDSU M20 BS O SC 1 G16 KDSU M20 BS O SC 2 G16 KDSU M20 BS O SC 1 G20S KDSU M20 BS O SC 2 G20S KDSU M20 BS O SC 1 G20 KDSU M20 BS O SC 2 G20 KDSU M25 BS O SC 1 G25 KDSU M25 BS O SC 2 G25 KDSU M32 BS O SC 1 G32 KDSU M32 BS O SC 2 G32 KDSU M40 BS O SC 1 G40 KDSU M40 BS O SC 2 G40 KDSU M50 BS O SC 1 G50S KDSU M50 BS O SC 2 G50S KDSU M50 BS O SC 1 G50 KDSU M50 BS O SC 2 G50 KDSU M63 BS O SC 1 G63S KDSU M63 BS O SC 2 G63S KDSU M63 BS O SC 1 G63 KDSU M63 BS O SC 2 G63 KDSU M75 BS O SC 1 G75 KDSU M75 BS O SC 2 G75 KDSU M75 BS O SC 1 G75S KDSU M75 BS O SC 2 G75S Note C.32 Thread D1 outer cable Ø D2 inner cable Ø Cable armour L/L1 SW MODR SUHB Qty. M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 25 / 1.5 M 25 / 1.5 M 32 / 1.5 M 32 / 1.5 M 40 / 1.5 M 40 / 1.5 M 50 / 1.5 M 50 / 1.5 M 50 / 1.5 M 50 / 1.5 M 63 / 1.5 M 63 / 1.5 M 63 / 1.5 M 63 / 1.5 M 75 / 1.5 M 75 / 1.5 M 75 / 1.5 M 75 / 1.5 6.70-10.30 9.00-13.50 9.40-12.50 11.50-16.00 12.00-17.60 15.50-21.10 16.80-23.90 20.30-27.40 23.20-30.50 26.70-34.00 28.60-36.20 33.00-40.60 34.80-42.20 39.40-46.70 41.10-48.50 45.70-53.20 47.50-54.80 52.10-59.50 53.80-61.20 58.40-65.80 66.50-73.40 71.10-78.00 60.20-68.00 64.80-72.20 3.40-8.40 3.40-8.40 7.20-11.70 7.20-11.70 9.40-14.00 9.40-14.00 13.50-20.00 13.50-20.00 19.50-26.30 19.50-26.30 23.00-32.20 23.00-32.20 28.10-38.20 28.10-38.20 33.10-44.10 33.10-44.10 39.20-50.10 39.20-50.10 46.70-56.00 46.70-56.00 58.00-68.00 58.00-68.00 52.10-62.00 52.10-62.00 0.15-1.25 0.15-1.25 0.15-1.25 0.15-1.25 0.15-1.25 0.15-1.25 0.15-1.6 0.15-1.6 0.15-2 0.15-2 0.2-2 0.2-2 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 78 / 16 78 / 16 78 / 16 78 / 16 78 / 16 78 / 16 90 / 16 90 / 16 105 / 16 105 / 16 113 / 16 113 / 16 125 / 16 125 / 16 125 / 16 125 / 16 125 / 19 125 / 19 125 / 19 125 / 19 131 / 19 131 / 19 131 / 19 131 / 19 24 24 24 24 30 30 38 38 46 46 55 55 65 65 65 65 80 80 80 80 90 90 90 90 32.5 32.5 32.5 32.5 32.5 32.5 50 50 80 80 80 80 100 100 100 100 160 160 160 160 200 200 200 200 L24 L24 L24 L24 EL30 EL30 EL38 EL38 EL46 EL46 EL55 EL55 EL65 EL65 EL65 EL65 EL80 EL80 EL80 EL80 EL90 EL90 EL90 EL90 20 20 20 20 20 20 20 20 10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 Order No. 0930001211 0930001212 0930011213 0930011214 0930021211 0930021212 0930031211 0930031212 0930041211 0930041212 1136870000 0930051212 0930061213 1136880000 1136890000 1136910000 1136920000 1136930000 1136940000 1136950000 1136980000 0930111212 1136960000 1136970000 • All cable glands have a thread pitch of 1.5 mm. • In the case of Ex d applications, the inner threads used for cable glands must meet the requirements of section 5.3 of EN/IEC 60079-1. In the screwed in position, at least 5 threads must be engaged. • If the cable glands are installed in non-metallic Ex e connection equipment, these must be connected to the protective earth of the system. • The connection cable must be laid securely and inflexibly to rule out tensile stress. 1420920000 – 2013 Cable glands for Ex applications - Brass Cable entries Klippon® cable glands - Brass - Ex e, Ex d, IP 68 for armoured and non-armoured cables All-purpose cable gland for cables and lines with single-wire armouring, metal-foil armouring and braided armouring. Non-armoured cables and lines can also be connected. L SW L1 C D2 D1 Thread Technical data Material O-Ring / Seal insert Temperature range Degree of protection Water depth Type of armouring Approval Brass, nickel-plated Silicone / Silicone -60 °C...180 °C IP 68 - 2.5 bar 25 m (30 Min.) Single-wire armouring, Metal foil armouring, Braided armouring ATEX ll 2 GD, Ex d llC / Ex e ll / Ex tD A21 IP68, IECEx Ex d IIC / Ex e ll Note Ordering data Typ metric, nickel-plated brass KDSU M20 BS O NI 1 G16 KDSU M20 BS O NI 2 G16 KDSU M20 BS O NI 1 G20 KDSU M20 BS O NI 2 G20 KDSU M20 BS O NI 1 G20S KDSU M20 BS O NI 2 G20S KDSU M25 BS O NI 1 G25 KDSU M25 BS O NI 2 G25 KDSU M32 BS O NI 1 G32 KDSU M32 BS O NI 2 G32 KDSU M40 BS O NI 1 G40 KDSU M40 BS O NI 2 G40 KDSU M50 BS O NI 1 G50 KDSU M50 BS O NI 2 G50 KDSU M50 BS O NI 1 G50S KDSU M50 BS O NI 2 G50S KDSU M63 BS O NI 1 G63 KDSU M63 BS O NI 2 G63 KDSU M63 BS O NI 1 G63S KDSU M63 BS O NI 2 G63S KDSU M75 BS O NI 1 G75 KDSU M75 BS O NI 2 G75 KDSU M75 BS O NI 1 G75S KDSU M75 BS O NI 2 G75S Note 1420920000 – 2013 Thread D1 outer cable Ø D2 inner cable Ø Cable armour L/L1 SW MODR SUHB Qty. M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 25 / 1.5 M 25 / 1.5 M 32 / 1.5 M 32 / 1.5 M 40 / 1.5 M 40 / 1.5 M 50 / 1.5 M 50 / 1.5 M 50 / 1.5 M 50 / 1.5 M 63 / 1.5 M 63 / 1.5 M 63 / 1.5 M 63 / 1.5 M 75 / 1.5 M 75 / 1.5 M 75 / 1.5 M 75 / 1.5 6.70-10.30 9.00-13.50 12.00-17.60 15.50-21.10 9.40-12.50 11.50-16.00 16.80-23.90 20.30-27.40 23.20-30.50 26.70-34.00 28.60-36.20 33.00-40.60 41.10-48.50 45.70-53.20 34.80-42.40 39.40-46.70 53.80-61.20 58.40-65.80 47.50-54.80 52.10-59.50 66.50-73.40 71.10-78.00 60.20-68.00 64.80-72.20 3.40-8.40 3.40-8.40 9.40-14.00 9.40-14.00 7.20-11.70 7.20-11.70 13.50-20.00 13.50-20.00 19.50-26.30 19.50-26.30 23.00-32.20 23.00-32.20 33.10-44.10 33.10-44.10 28.10-38.20 28.10-38.20 46.70-56.00 46.70-56.00 39.20-50.10 39.20-50.10 58.00-68.00 58.00-68.00 52.10-62.00 52.10-62.00 0.15-1.25 0.15-1.25 0.15-1.25 0.15-1.25 0.15-1.25 0.15-1.25 0.15-1.6 0.15-1.6 0.15-2 0.15-2 0.2-2 0.2-2 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 0.3-2.5 78 / 16 78 / 16 78 / 16 78 / 16 78 / 16 78 / 16 90 / 16 90 / 16 105 / 16 105 / 16 113 / 16 113 / 16 125 / 16 125 / 16 125 / 16 125 / 16 125 / 19 125 / 19 125 / 19 125 / 19 131 / 19 131 / 19 131 / 19 131 / 19 24 24 30 30 24 24 38 38 46 46 55 55 65 65 65 65 80 80 80 80 90 90 90 90 32.5 32.5 32.5 32.5 32.5 32.5 50 50 80 80 80 80 100 100 100 100 160 160 160 160 200 200 200 200 L24 L24 EL30 EL30 L24 L24 EL38 EL38 EL46 EL46 EL55 EL55 EL65 EL65 EL65 EL65 EL80 EL80 EL80 EL80 EL90 EL90 EL90 EL90 20 20 20 20 20 20 20 20 10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 Order No. 0930001221 0930001222 0930021221 0930021222 0930011223 0930011224 0930031221 0930031222 0930041221 0930041222 1136990000 0930051222 1137010000 1137020000 1137000000 0930061224 1137050000 0930091222 1137030000 1137040000 1137080000 1137090000 1137060000 1137070000 • All cable glands have a thread pitch of 1.5 mm. • In the case of Ex d applications, the inner threads used for cable glands must meet the requirements of section 5.3 of EN/IEC 60079-1. In the screwed in position, at least 5 threads must be engaged. • If the cable glands are installed in non-metallic Ex e connection equipment, these must be connected to the protective earth of the system. • The connection cable must be laid securely and inflexibly to rule out tensile stress. C.33 Cable glands for Ex applications - Brass Cable entries Klippon® cable glands - Brass - Ex e, Ex d, IP 66 / IP 68 for armoured cables D1 SW Cable gland for cables and lines with single-wire armouring. D2 C L1 L Technical data Material Seal insert Temperature range Protection degree Protection degree with GWDR Water depth Type of armouring Approval Note Brass CR -20 °C...85 °C IP 54 IP 66, IP 68 - 2.5 bar 25 m (30 Min.) Single-wire armouring ATEX ll 2 GD, Ex d llC / Ex e ll / Ex tD A21 IP68, IECEx Ex d IIC / Ex e ll IP protection without GWDR is IP 54. To achieve IP 66/68 protection, a nylon GWDR must be ordered separately. Ordering data Typ metric, brass KDSW M20 BN O SC 1 G16 KDSW M20BN O SC 2 G16 KDSW M20 BN O SC 1 G20S KDSW M20 BN O SC 2 G20S KDSW M20 BN O SC 1 G20 KDSW M20 BN O SC 2 G20 KDSW M25 BN O SC 1 G25 KDSW M25 BN O SC 2 G25 KDSW M32 BN O SC 1 G32 KDSW M32 BN O SC 2 G32 KDSW M40 BN O SC 1 G40 KDSW M40 BN O SC 2 G40 KDSW M50 BN O SC 1 G50S KDSW M50 BN O SC 2 G50S KDSW M50 BN O SC 1 G50 KDSW M50 BN O SC 2 G50 KDSW M63 BN O SC 1 G63S KDSW M63 BN O SC 2 G63S KDSW M63 BN O SC 1 G63 KDSW M63 BN O SC 2 G63 KDSW M75 BN O SC 1 G75S KDSW M75 BN O SC 2 G75S KDSW M75 BN O SC 1 G75 KDSW M75 BN O SC 2 G75 Note C.34 Thread D1 outer cable Ø D2 inner cable Ø Cable armour L/L1 SW MODR SUHB Qty. M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 25 / 1.5 M 25 / 1.5 M 32 / 1.5 M 32 / 1.5 M 40 / 1.5 M 40 / 1.5 M 50 / 1.5 M 50 / 1.5 M 50 / 1.5 M 50 / 1.5 M 63 / 1.5 M 63 / 1.5 M 63 / 1.5 M 63 / 1.5 M 75 / 1.5 M 75 / 1.5 M 75 / 1.5 M 75 / 1.5 4.90-10.00 8.40-13.50 9.40-12.50 11.50-16.00 12.00-17.60 15.50-21.10 16.80-23.90 20.30-27.40 23.20-30.50 26.70-34.00 28.60-36.20 33.00-40.60 34.80-42.40 39.40-46.70 41.10-48.50 45.70-53.20 47.50-54.80 52.10-59.50 53.80-61.20 58.40-65.80 60.20-68.00 64.80-72.20 66.50-73.40 71.10-78.00 4.00-8.40 4.00-8.40 8.00-11.70 8.00-11.70 6.70-14.00 6.70-14.00 13.00-20.00 13.00-20.00 19.00-26.30 19.00-26.30 25.00-32.20 25.00-32.20 31.50-38.20 31.50-38.20 36.50-44.10 36.50-44.10 42.50-50.10 42.50-50.10 49.50-56.00 49.50-56.00 54.50-62.00 54.50-62.00 60.50-68.00 60.50-68.00 0.9 0.9 0.9-1.25 0.9-1.25 0.9-1.25 0.9-1.25 1.25-1.6 1.25-1.6 1.6-2 1.6-2 1.6-2 1.6-2 2-2.5 2-2.5 2-2.5 2-2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 65 / 16 65 / 16 72 / 16 72 / 16 73 / 16 73 / 16 73 / 16 73 / 16 76 / 19 76 / 19 76 / 19 76 / 19 82 / 19 82 / 19 82 / 19 82 / 19 24 24 30 30 24 24 38 38 46 46 55 55 65 65 65 65 80 80 80 80 90 90 90 90 32.5 32.5 32.5 32.5 32.5 32.5 47.5 47.5 55 55 65 65 80 80 80 80 95 95 95 95 110 110 110 110 L24 L24 L24 L24 L30 L30 L38 L38 L46 L46 L55 L55 L65 L65 L65 L65 L80 L80 L80 L80 L90 L90 L90 L90 20 20 20 20 20 20 20 20 10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 Order No. 1074480000 1074490000 1074500000 1074510000 1074520000 1074530000 1074540000 1074550000 1074570000 1074580000 1074590000 1074610000 1074620000 1074630000 1074640000 1074650000 1074670000 1074710000 1074730000 1074750000 1074770000 1074790000 1074820000 1074840000 • All cable glands have a thread pitch of 1.5 mm. • In the case of Ex d applications, the inner threads used for cable glands must meet the requirements of section 5.3 of EN/IEC 60079-1. In the screwed in position, at least 5 threads must be engaged. • If the cable glands are installed in non-metallic Ex e connection equipment, these must be connected to the protective earth of the system. • The connection cable must be laid securely and inflexibly to rule out tensile stress. 1420920000 – 2013 Cable glands for Ex applications - Brass Cable entries Klippon® cable glands - Brass - Ex e, Ex d, IP 66 / IP 68 for armoured cables D1 SW Cable gland for cables and lines with single-wire armouring. D2 C L1 L Technical data Material Seal insert Temperature range Protection degree Protection degree with GWDR Water depth Type of armouring Approval Brass, nickel-plated CR -20 °C...85 °C IP 54 IP 66, IP 68 - 2.5 bar 25 m (30 Min.) Single-wire armouring ATEX ll 2 GD, Ex d llC / Ex e ll / Ex tD A21 IP68, IECEx Ex d IIC / Ex e ll Note IP protection without GWDR is IP 54. To achieve IP 66/68 protection, a nylon GWDR must be ordered separately. Ordering data Typ metric, nickel-plated brass KDSW M20 BN O NI 1 G16 KDSW M20 BN O NI 2 G16 KDSW M20 BN O NI 1 G20 KDSW M20 BN O NI 2 G20 KDSW M20 BN O NI 1 G20S KDSW M20 BN O NI 2 G20S KDSW M25 BN O NI 1 G25 KDSW M25 BN O NI 2 G25 KDSW M32 BN O NI 1 G32 KDSW M32 BN O NI 2 G32 KDSW M40 BN O NI 1 G40 KDSW M40 BN O NI 2 G40 KDSW M50 BN O NI 1 G50 KDSW M50 BN O NI 2 G50 KDSW M50 BN O NI 1 G50S KDSW M50 BN O NI 2 G50S KDSW M63 BN O NI 1 G63 KDSW M63 BN O NI 2 G63 KDSW M63 BN O NI 1 G63S KDSW M63 BN O NI 2 G63S KDSW M75 BN O NI 1 G75 KDSW M75 BN O NI 2 G75 KDSW M75 BN O NI 1 G75S KDSW M75 BN O NI 2 G75S Note 1420920000 – 2013 Thread D1 outer cable Ø D2 inner cable Ø Cable armour L/L1 SW MODR SUHB Qty. M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 25 / 1.5 M 25 / 1.5 M 32 / 1.5 M 32 / 1.5 M 40 / 1.5 M 40 / 1.5 M 50 / 1.5 M 50 / 1.5 M 50 / 1.5 M 50 / 1.5 M 63 / 1.5 M 63 / 1.5 M 63 / 1.5 M 63 / 1.5 M 75 / 1.5 M 75 / 1.5 M 75 / 1.5 M 75 / 1.5 4.90-10.00 8.40-13.50 12.00-17.60 15.50-21.10 9.40-12.50 11.50-16.00 16.80-23.90 20.30-27.40 23.20-30.50 26.70-34.00 28.60-36.20 33.00-40.60 41.10-48.50 45.70-53.20 34.80-42.40 39.40-46.70 53.80-61.20 58.40-65.80 47.50-54.80 52.10-59.50 66.50-73.40 71.10-78.00 60.20-68.00 64.80-72.20 4.00-8.40 4.00-8.40 6.70-14.00 6.70-14.00 8.00-11.70 8.00-11.70 13.00-20.00 13.00-20.00 19.00-26.30 19.00-26.30 25.00-32.20 25.00-32.20 36.50-44.10 36.50-44.10 31.50-38.20 31.50-38.20 49.50-56.00 49.50-56.00 42.50-50.10 42.50-50.10 60.50-68.00 60.50-68.00 54.50-62.00 54.50-62.00 0.9 0.9 0.9-1.25 0.9-1.25 0.9-1.25 0.9-1.25 1.25-1.6 1.25-1.6 1.6-2 1.6-2 1.6-2 1.6-2 2-2.5 2-2.5 2-2.5 2-2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 65 / 16 65 / 16 72 / 16 72 / 16 73 / 16 73 / 16 73 / 16 73 / 16 76 / 19 76 / 19 76 / 19 76 / 19 82 / 19 82 / 19 82 / 19 82 / 19 24 24 30 24 30 24 38 38 46 46 55 55 65 65 65 65 80 80 80 80 90 90 90 90 32.5 32.5 32.5 32.5 32.5 32.5 47.5 47.5 55 55 65 65 80 80 80 80 95 95 95 95 110 110 110 110 L24 L24 L30 L30 L24 L24 L38 L38 L46 L46 L55 L55 L65 L65 L65 L65 L80 L80 L80 L80 L90 L90 L90 L90 20 20 20 20 20 20 20 20 10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 Order No. 1075030000 1075040000 1075070000 1075080000 1075050000 1075060000 1075090000 1075110000 1075120000 1075130000 1075140000 1075150000 1075180000 1075190000 1075160000 1075170000 1075230000 1075240000 1075210000 1075220000 1075270000 1075280000 1075250000 1075260000 • All cable glands have a thread pitch of 1.5 mm. • In the case of Ex d applications, the inner threads used for cable glands must meet the requirements of section 5.3 of EN/IEC 60079-1. In the screwed in position, at least 5 threads must be engaged. • If the cable glands are installed in non-metallic Ex e connection equipment, these must be connected to the protective earth of the system. • The connection cable must be laid securely and inflexibly to rule out tensile stress. C.35 Cable glands for Ex applications - Brass Cable entries Klippon® cable glands - Brass - Ex e, Ex d, IP 66 / IP 68 for armoured cables D1 SW Cable gland for cables and lines with single-wire armouring. D2 C L1 L Technical data Material Seal insert Temperature range Protection degree Protection degree with GWDR Water depth Type of armouring Approval Note Brass Silicone -60 °C...180 °C IP 54 IP 66, IP 68 - 2.5 bar 25 m (30 Min.) Single-wire armouring ATEX ll 2 GD, Ex d llC / Ex e ll / Ex tD A21 IP68, IECEx Ex d IIC / Ex e ll IP protection without GWDR is IP 54. To achieve IP 66/68 protection, a nylon GWDR must be ordered separately. Ordering data Typ metric, brass KDSW M20 BS O SC 1 G16 KDSW M20 BS O SC 2 G16 KDSW M20 BS O SC 1 G20S KDSW M20 BS O SC 2 G20S KDSW M20 BS O SC 1 G20 KDSW M20 BS O SC 2 G20 KDSW M25 BS O SC 1 G25 KDSW M25 BS O SC 2 G25 KDSW M32 BS O SC 1 G32 KDSW M32 BS O SC 2 G32 KDSW M40 BS O SC 1 G40 KDSW M40 BS O SC 2 G40 KDSW M50 BS O SC 1 G50S KDSW M50 BS O SC 2 G50S KDSW M50 BS O SC 1 G50 KDSW M50 BS O SC 2 G50 KDSW M63 BS O SC 1 G63S KDSW M63 BS O SC 2 G63S KDSW M63 BS O SC 1 G63 KDSW M63 BS O SC 2 G63 KDSW M75 BS O SC 1 G75S KDSW M75 BS O SC 2 G75S KDSW M75 BS O SC 1 G75 KDSW M75 BS O SC 2 G75 Note C.36 Thread D1 outer cable Ø D2 inner cable Ø Cable armour L/L1 SW MODR SUHB Qty. M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 25 / 1.5 M 25 / 1.5 M 32 / 1.5 M 32 / 1.5 M 40 / 1.5 M 40 / 1.5 M 50 / 1.5 M 50 / 1.5 M 50 / 1.5 M 50 / 1.5 M 63 / 1.5 M 63 / 1.5 M 63 / 1.5 M 63 / 1.5 M 75 / 1.5 M 75 / 1.5 M 75 / 1.5 M 75 / 1.5 4.90-10.00 8.40-13.50 9.40-12.50 11.50-16.00 12.00-17.60 15.50-21.10 16.80-23.90 20.30-27.40 23.20-30.50 26.70-34.00 28.60-36.20 33.00-40.60 34.80-42.40 39.40-46.70 41.10-48.50 45.70-53.20 47.50-54.80 52.10-59.50 53.80-61.20 58.40-65.80 60.20-68.00 64.80-72.20 66.50-73.40 71.10-78.00 4.00-8.40 4.00-8.40 8.00-11.70 8.00-11.70 6.70-14.00 6.70-14.00 13.00-20.00 13.00-20.00 19.00-26.30 19.00-26.30 25.00-32.20 25.00-32.20 31.50-38.20 31.50-38.20 36.50-44.10 36.50-44.10 42.50-50.10 42.50-50.10 49.50-56.00 49.50-56.00 54.50-62.00 54.50-62.00 60.50-68.00 60.50-68.00 0.9 0.9 0.9-1.25 0.9-1.25 0.9-1.25 0.9-1.25 1.25-1.6 1.25-1.6 1.6-2 1.6-2 1.6-2 1.6-2 2-2.5 2-2.5 2-2.5 2-2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 65 / 16 65 / 16 72 / 16 72 / 16 73 / 16 73 / 16 73 / 16 73 / 16 76 / 19 76 / 19 76 / 19 76 / 19 82 / 19 82 / 19 82 / 19 82 / 19 24 24 24 24 30 30 38 38 46 46 55 55 65 65 65 65 80 80 80 80 90 90 90 90 32.5 32.5 32.5 32.5 32.5 32.5 47.5 47.5 55 55 65 65 80 80 80 80 95 95 95 95 110 110 110 110 L24 L24 L24 L24 L30 L30 L38 L38 L46 L46 L55 L55 L65 L65 L65 L65 L80 L80 L80 L80 L90 L90 L90 L90 20 20 20 20 20 20 20 20 10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 Order No. 1136160000 1136170000 1136180000 1136190000 1136200000 1136210000 1136220000 1136230000 1136240000 1136250000 1136260000 1136270000 1136280000 1136290000 1136310000 1136320000 1136330000 1136340000 1136350000 1136360000 1136370000 1136380000 1136390000 1136400000 • All cable glands have a thread pitch of 1.5 mm. • In the case of Ex d applications, the inner threads used for cable glands must meet the requirements of section 5.3 of EN/IEC 60079-1. In the screwed in position, at least 5 threads must be engaged. • If the cable glands are installed in non-metallic Ex e connection equipment, these must be connected to the protective earth of the system. • The connection cable must be laid securely and inflexibly to rule out tensile stress. 1420920000 – 2013 Cable glands for Ex applications - Brass Cable entries Klippon® cable glands - Brass - Ex e, Ex d, IP 66 / IP 68 for armoured cables D1 SW Cable gland for cables and lines with single-wire armouring. D2 C L1 L Technical data Material Seal insert Temperature range Protection degree Protection degree with GWDR Water depth Type of armouring Approval Brass, nickel-plated Silicone -60 °C...180 °C IP 54 IP 66, IP 68 - 2.5 bar 25 m (30 Min.) Single-wire armouring ATEX ll 2 GD, Ex d llC / Ex e ll / Ex tD A21 IP68, IECEx Ex d IIC / Ex e ll Note IP protection without GWDR is IP 54. To achieve IP 66/68 protection, a nylon GWDR must be ordered separately. Ordering data Typ metric, nickel-plated brass KDSW M20 BS O NI 1 G16 KDSW M20 BS O NI 2 G16 KDSW M20 BS O NI 1 G20 KDSW M20 BS O NI 2 G20 KDSW M20 BS O NI 1 G20S KDSW M20 BS O NI 2 G20S KDSW M25 BS O NI 1 G25 KDSW M25 BS O NI 2 G25 KDSW M32 BS O NI 1 G32 KDSW M32 BS O NI 2 G32 KDSW M40 BS O NI 1 G40 KDSW M40 BS O NI 2 G40 KDSW M50 BS O NI 1 G50 KDSW M50 BS O NI 2 G50 KDSW M50 BS O NI 1 G50S KDSW M50 BS O NI 2 G50S KDSW M63 BS O NI 1 G63 KDSW M63 BS O NI 2 G63 KDSW M63 BS O NI 1 G63S KDSW M63 BS O NI 2 G63S KDSW M75 BS O NI 1 G75 KDSW M75 BS O NI 2 G75 KDSW M75 BS O NI 1 G75S KDSW M75 BS O NI 2 G75S Note 1420920000 – 2013 Thread D1 outer cable Ø D2 inner cable Ø Cable armour L/L1 SW MODR SUHB Qty. M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 25 / 1.5 M 25 / 1.5 M 32 / 1.5 M 32 / 1.5 M 40 / 1.5 M 40 / 1.5 M 50 / 1.5 M 50 / 1.5 M 50 / 1.5 M 50 / 1.5 M 63 / 1.5 M 63 / 1.5 M 63 / 1.5 M 63 / 1.5 M 75 / 1.5 M 75 / 1.5 M 75 / 1.5 M 75 / 1.5 4.90-10.00 8.40-13.50 12.00-17.60 15.50-21.10 9.40-12.50 11.50-16.00 16.80-23.90 20.30-27.40 23.20-30.50 26.70-34.00 28.60-36.20 33.00-40.60 41.10-48.50 45.70-53.20 34.80-42.40 39.40-46.70 53.80-61.20 58.40-65.80 47.50-54.80 52.10-59.50 66.50-73.40 71.10-78.00 60.20-68.00 64.80-72.20 4.00-8.40 4.00-8.40 6.70-14.00 6.70-14.00 8.00-11.70 8.00-11.70 13.00-20.00 13.00-20.00 19.00-26.30 19.00-26.30 25.00-32.20 25.00-32.20 36.50-44.10 36.50-44.10 31.50-38.20 31.50-38.20 49.50-56.00 49.50-56.00 42.50-50.10 42.50-50.10 60.50-68.00 60.50-68.00 54.50-62.00 54.50-62.00 0.9 0.9 0.9-1.25 0.9-1.25 0.9-1.25 0.9-1.25 1.25-1.6 1.25-1.6 1.6-2 1.6-2 1.6-2 1.6-2 2-2.5 2-2.5 2-2.5 2-2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 65 / 16 65 / 16 72 / 16 72 / 16 73 / 16 73 / 16 73 / 16 73 / 16 76 / 19 76 / 19 76 / 19 76 / 19 82 / 19 82 / 19 82 / 19 82 / 19 24 24 30 24 30 24 38 38 46 46 55 55 65 65 65 65 80 80 80 80 90 90 90 90 32.5 32.5 32.5 32.5 32.5 32.5 47.5 47.5 55 55 65 65 80 80 80 80 95 95 95 95 110 110 110 110 L24 L24 L30 L30 L24 L24 L38 L38 L46 L46 L55 L55 L65 L65 L65 L65 L80 L80 L80 L80 L90 L90 L90 L90 20 20 20 20 20 20 20 20 10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 Order No. 1136410000 1136420000 1136450000 1136460000 1136430000 1136440000 1136470000 1136480000 1136490000 1136510000 1136520000 1136530000 1136560000 1136570000 1136540000 1136550000 1136600000 1136610000 1136580000 1136590000 1136640000 1136650000 1136620000 1136630000 • All cable glands have a thread pitch of 1.5 mm. • In the case of Ex d applications, the inner threads used for cable glands must meet the requirements of section 5.3 of EN/IEC 60079-1. In the screwed in position, at least 5 threads must be engaged. • If the cable glands are installed in non-metallic Ex e connection equipment, these must be connected to the protective earth of the system. • The connection cable must be laid securely and inflexibly to rule out tensile stress. C.37 Cable glands for Ex applications - Brass Cable entries Klippon® cable glands - Brass - Ex e, Ex d, IP 66 / IP 68 for armoured cables D1 SW Cable gland for cables and lines with single-wire armouring and lead-sheath armouring. D2 C L1 L Technical data Material Seal insert Temperature range Protection degree Protection degree with GWDR Water depth Type of armouring Approval Note Brass CR -20 °C...85 °C IP 54 IP 66, IP 68 - 2.5 bar 25 m (30 Min.) Single-wire armouring, Lead sheath armouring ATEX ll 2 GD, Ex d llC / Ex e ll / Ex tD A21 IP68, IECEx Ex d IIC / Ex e ll IP protection without GWDR is IP 54. To achieve IP 66/68 protection, a nylon GWDR must be ordered separately. Ordering data Typ metric, brass KDSW M20 BN L SC 1 G16 KDSW M20 BN L SC 2 G16 KDSW M20 BN L SC 1 G20S KDSW M20 BN L SC 2 G20S KDSW M20 BN L SC 1 G20 KDSW M20 BN L SC 2 G20 KDSW M25 BN L SC 1 G25 KDSW M25 BN L SC 2 G25 KDSW M32 BN L SC 1 G32 KDSW M32 BN L SC 2 G32 KDSW M40 BN L SC 1 G40 KDSW M40 BN L SC 2 G40 KDSW M50 BN L SC 1 G50S KDSW M50 BN L SC 2 G50S KDSW M50 BN L SC 1 G50 KDSW M50 BN L SC 2 G50 KDSW M63 BN L SC 1 G63S KDSW M63 BN L SC 2 G63S KDSW M63 BN L SC 1 G63 KDSW M63 BN L SC 2 G63 KDSW M75 BN L SC 1 G75S KDSW M75 BN L SC 2 G75S KDSW M75 BN L SC 1 G75 KDSW M75 BN L SC 2 G75 Note C.38 Thread D1 outer cable Ø D2 inner cable Ø Cable armour L/L1 SW MODR SUHB Qty. M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 25 / 1.5 M 25 / 1.5 M 32 / 1.5 M 32 / 1.5 M 40 / 1.5 M 40 / 1.5 M 50 / 1.5 M 50 / 1.5 M 50 / 1.5 M 50 / 1.5 M 63 / 1.5 M 63 / 1.5 M 63 / 1.5 M 63 / 1.5 M 75 / 1.5 M 75 / 1.5 M 75 / 1.5 M 75 / 1.5 4.90-10.00 8.40-13.50 9.40-12.50 11.50-16.00 12.00-17.60 15.50-21.10 16.80-23.90 20.30-27.40 23.20-30.50 26.70-34.00 28.60-36.20 33.00-40.60 34.80-42.40 39.40-46.70 41.10-48.50 45.70-53.20 47.50-54.80 52.10-59.50 53.80-61.20 58.40-65.80 60.20-68.00 64.80-72.20 66.50-73.40 71.10-78.00 4.00-8.40 4.00-8.40 8.00-11.70 8.00-11.70 6.70-14.00 6.70-14.00 13.00-20.00 13.00-20.00 19.00-26.30 19.00-26.30 25.00-32.20 25.00-32.20 31.50-38.20 31.50-38.20 36.50-44.10 36.50-44.10 42.50-50.10 42.50-50.10 49.50-56.00 49.50-56.00 54.50-62.00 54.50-62.00 60.50-68.00 60.50-68.00 0.9 0.9 0.9-1.25 0.9-1.25 0.9-1.25 0.9-1.25 1.25-1.6 1.25-1.6 1.6-2 1.6-2 1.6-2 1.6-2 2-2.5 2-2.5 2-2.5 2-2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 65 / 16 65 / 16 72 / 16 72 / 16 73 / 16 73 / 16 73 / 16 73 / 16 76 / 19 76 / 19 76 / 19 76 / 19 82 / 19 82 / 19 82 / 19 82 / 19 24 24 24 24 30 30 38 38 46 46 55 55 65 65 65 65 80 80 80 80 90 90 90 90 32.5 32.5 32.5 32.5 32.5 32.5 47.5 47.5 55 55 65 65 80 80 80 80 95 95 95 95 110 110 110 110 L24 L24 L24 L24 L30 L30 L38 L38 L46 L46 L55 L55 L65 L65 L65 L65 L80 L80 L80 L80 L90 L90 L90 L90 20 20 20 20 20 20 20 20 10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 Order No. 1076250000 1076270000 1076280000 1076290000 1076300000 1076310000 1076320000 1076330000 1076340000 1076350000 1076360000 1076370000 1076380000 1076390000 1076400000 1076410000 1076420000 1076430000 1076440000 1076450000 1076460000 1076470000 1076480000 1076490000 • All cable glands have a thread pitch of 1.5 mm. • In the case of Ex d applications, the inner threads used for cable glands must meet the requirements of section 5.3 of EN/IEC 60079-1. In the screwed in position, at least 5 threads must be engaged. • If the cable glands are installed in non-metallic Ex e connection equipment, these must be connected to the protective earth of the system. • The connection cable must be laid securely and inflexibly to rule out tensile stress. 1420920000 – 2013 Cable glands for Ex applications - Brass Cable entries Klippon® cable glands - Brass - Ex e, Ex d, IP 66 / IP 68 for armoured cables D1 SW Cable gland for cables and lines with single-wire armouring and lead-sheath armouring. D2 L C L1 Technical data Material Seal insert Temperature range Protection degree Protection degree with GWDR Water depth Type of armouring Approval Note Brass, nickel-plated CR -20 °C...85 °C IP 54 IP 66, IP 68 - 2.5 bar 25 m (30 Min.) Single-wire armouring, Lead sheath armouring ATEX ll 2 GD, Ex d llC / Ex e ll / Ex tD A21 IP68, IECEx Ex d IIC / Ex e ll IP protection without GWDR is IP 54. To achieve IP 66/68 protection, a nylon GWDR must be ordered separately. Ordering data Typ metric, nickel-plated brass KDSW M20 BN L NI 1 G16 KDSW M20 BN L NI 2 G16 KDSW M20 BN L NI 1 G20 KDSW M20 BN L NI 2 G20 KDSW M20 BN L NI 1 G20S KDSW M20 BN L NI 2 G20S KDSW M25 BN L NI 1 G25 KDSW M25 BN L NI 2 G25 KDSW M32 BN L NI 1 G32 KDSW M32 BN L NI 2 G32 KDSW M40 BN L NI 1 G40 KDSW M40 BN L NI 2 G40 KDSW M50 BN L NI 1 G50 KDSW M50 BN L NI 2 G50 KDSW M50 BN L NI 1 G50S KDSW M50 BN L NI 2 G50S KDSW M63 BN L NI 1 G63 KDSW M63 BN L NI 2 G63 KDSW M63 BN L NI 1 G63S KDSW M63 BN L NI 2 G63S KDSW M75 BN L NI 1 G75 KDSW M75 BN L NI 2 G75 KDSW M75 BN L NI 1 G75S KDSW M75 BN L NI 2 G75S Note 1420920000 – 2013 Thread D1 outer cable Ø D2 inner cable Ø Cable armour L/L1 SW MODR SUHB Qty. M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 25 / 1.5 M 25 / 1.5 M 32 / 1.5 M 32 / 1.5 M 40 / 1.5 M 40 / 1.5 M 50 / 1.5 M 50 / 1.5 M 50 / 1.5 M 50 / 1.5 M 63 / 1.5 M 63 / 1.5 M 63 / 1.5 M 63 / 1.5 M 75 / 1.5 M 75 / 1.5 M 75 / 1.5 M 75 / 1.5 4.90-10.00 8.40-13.50 12.00-17.60 15.50-21.10 9.40-12.50 11.50-16.00 16.80-23.90 20.30-27.40 23.20-30.50 26.70-34.00 28.60-36.20 33.00-40.60 41.40-48.50 45.70-53.20 34.80-42.40 39.40-46.70 53.80-61.20 58.40-65.80 47.50-54.80 52.10-59.50 66.50-73.40 71.10-78.00 60.20-68.00 64.80-72.20 4.00-8.40 4.00-8.40 6.70-14.00 6.70-14.00 8.00-11.70 8.00-11.70 13.00-20.00 13.00-20.00 19.00-26.30 19.00-26.30 25.00-32.20 25.00-32.20 36.50-44.10 36.50-44.10 31.50-38.20 31.50-38.20 49.50-56.00 49.50-56.00 42.50-50.10 42.50-50.10 60.50-68.00 60.50-68.00 54.50-62.00 54.50-62.00 0.9 0.9 0.9-1.25 0.9-1.25 0.9-1.25 0.9-1.25 1.25-1.6 1.25-1.6 1.6-2 1.6-2 1.6-2 1.6-2 2-2.5 2-2.5 2-2.5 2-2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 65 / 16 65 / 16 72 / 16 72 / 16 73 / 16 73 / 16 73 / 16 73 / 16 76 / 19 76 / 19 76 / 19 76 / 19 82 / 19 82 / 19 82 / 19 82 / 19 24 24 30 30 24 24 38 38 46 46 55 55 65 65 65 65 80 80 80 80 90 90 90 90 32.5 32.5 32.5 32.5 32.5 32.5 47.5 47.5 55 55 65 65 80 80 80 80 95 95 95 95 110 110 110 110 L24 L24 L30 L30 L24 L24 L38 L38 L46 L46 L55 L55 L65 L65 L65 L65 L80 L80 L80 L80 L90 L90 L90 L90 20 20 20 20 20 20 20 20 10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 Order No. 1074660000 1074690000 1074760000 1074780000 1074720000 1074740000 1074810000 1074830000 1074850000 1074860000 1074870000 1074880000 1074920000 1074930000 1074890000 1074910000 1074960000 1074970000 1074940000 1074950000 1075010000 1075020000 1074980000 1074990000 • All cable glands have a thread pitch of 1.5 mm. • In the case of Ex d applications, the inner threads used for cable glands must meet the requirements of section 5.3 of EN/IEC 60079-1. In the screwed in position, at least 5 threads must be engaged. • If the cable glands are installed in non-metallic Ex e connection equipment, these must be connected to the protective earth of the system. • The connection cable must be laid securely and inflexibly to rule out tensile stress. C.39 Cable glands for Ex applications - Brass Cable entries Klippon® cable glands - Brass - Ex e, Ex d, IP 66 / IP 68 for armoured cables D1 SW Cable gland for cables and lines with braided armouring. D2 C L1 L Technical data Material Seal insert Temperature range Protection degree Protection degree with GWDR Water depth Type of armouring Approval Brass Silicone -60 °C...180 °C IP 54 IP 66, IP 68 - 2.5 bar 25 m (30 Min.) Braided armouring ATEX ll 2 GD, Ex d llC / Ex e ll / Ex tD A21 IP68, IECEx Ex d IIC / Ex e ll Note IP protection without GWDR is IP 54. To achieve IP 66/68 protection, a nylon GWDR must be ordered separately. Ordering data Typ metric, brass KDSX M20 BS O SC 1 G16 KDSX M20 BS O SC 2 G16 KDSX M20 BS O SC 1 G20S KDSX M20 BS O SC 2 G20S KDSX M20 BS O SC 1 G20 KDSX M20 BS O SC 2 G20 KDSX M25 BS O SC 1 G25 KDSX M25 BS O SC 2 G25 KDSX M32 BS O SC 1 G32 KDSX M32 BS O SC 2 G32 KDSX M40 BS O SC 1 G40 KDSX M40 BS O SC 2 G40 KDSX M50 BS O SC 1 G50S KDSX M50 BS O SC 2 G50S KDSX M50 BS O SC 1 G50 KDSX M50 BS O SC 2 G50 KDSX M63 BS O SC 1 G63S KDSX M63 BS O SC 2 G63S KDSX M63 BS O SC 1 G63 KDSX M63 BS O SC 2 G63 KDSX M75 BS O SC 1 G75S KDSX M75 BS O SC 2 G75S KDSX M75 BS O SC 1 G75 KDSX M75 BS O SC 2 G75 Note C.40 Thread D1 outer cable Ø D2 inner cable Ø Cable armour L/L1 SW MODR SUHB Qty. M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 25 / 1.5 M 25 / 1.5 M 32 / 1.5 M 32 / 1.5 M 40 / 1.5 M 40 / 1.5 M 50 / 1.5 M 50 / 1.5 M 50 / 1.5 M 50 / 1.5 M 63 / 1.5 M 63 / 1.5 M 63 / 1.5 M 63 / 1.5 M 75 / 1.5 M 75 / 1.5 M 75 / 1.5 M 75 / 1.5 4.90-10.00 8.40-13.50 9.40-12.50 11.50-16.00 12.00-17.60 15.50-21.10 16.80-23.90 20.30-27.40 23.20-30.50 26.70-34.00 28.60-36.20 33.00-40.60 34.80-42.40 39.40-46.70 41.10-48.50 45.70-53.20 47.50-54.80 52.10-59.50 53.80-61.20 58.40-65.80 60.20-68.00 64.80-72.20 66.50-73.40 71.10-78.00 4.00-8.40 4.00-8.40 8.00-11.70 8.00-11.70 6.70-14.00 6.70-14.00 13.00-20.00 13.00-20.00 19.00-26.30 19.00-26.30 25.00-32.20 25.00-32.20 31.50-38.20 31.50-38.20 36.50-44.10 36.50-44.10 42.50-50.10 42.50-50.10 49.50-56.00 49.50-56.00 54.50-62.00 54.50-62.00 60.50-68.00 60.50-68.00 0.15-0.35 0.15-0.35 0.15-0.35 0.15-0.35 0.15-0.5 0.15-0.5 0.15-0.5 0.15-0.5 0.15-0.55 0.15-0.55 0.2-0.6 0.2-0.6 0.2-0.6 0.2-0.6 0.3-0.8 0.3-0.8 0.3-0.8 0.3-0.8 0.3-0.8 0.3-0.8 0.3-1 0.3-1 0.3-1 0.3-1 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 65 / 16 65 / 16 72 / 16 72 / 16 73 / 16 73 / 16 73 / 16 73 / 16 76 / 19 76 / 19 76 / 19 76 / 19 82 / 19 82 / 19 82 / 19 82 / 19 24 24 24 24 30 30 38 38 46 46 55 55 65 65 65 65 80 80 80 80 90 90 90 90 32.5 32.5 32.5 32.5 32.5 32.5 47.5 47.5 55 55 65 65 80 80 80 80 95 95 95 95 110 110 110 110 L24 L24 L24 L24 L30 L30 L38 L38 L46 L46 L55 L55 L65 L65 L65 L65 L80 L80 L80 L80 L90 L90 L90 L90 20 20 20 20 20 20 20 20 10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 Order No. 1135650000 1135660000 1135670000 1135680000 1135690000 1135710000 1135720000 1135730000 1135740000 1135750000 1135760000 1135770000 1135780000 1135790000 1135800000 1135810000 1135820000 1135830000 1135840000 1135850000 1135860000 1135870000 1135880000 1135890000 • All cable glands have a thread pitch of 1.5 mm. • In the case of Ex d applications, the inner threads used for cable glands must meet the requirements of section 5.3 of EN/IEC 60079-1. In the screwed in position, at least 5 threads must be engaged. • If the cable glands are installed in non-metallic Ex e connection equipment, these must be connected to the protective earth of the system. • The connection cable must be laid securely and inflexibly to rule out tensile stress. 1420920000 – 2013 Cable glands for Ex applications - Brass Cable entries Klippon® cable glands - Brass - Ex e, Ex d, IP 66 / IP 68 for armoured cables D1 SW Cable gland for cables and lines with braided armouring. D2 C L1 L Technical data Material Seal insert Temperature range Protection degree Protection degree with GWDR Water depth Type of armouring Approval Note Brass, nickel-plated Silicone -60 °C...180 °C IP 54 IP 66, IP 68 - 2.5 bar 25 m (30 Min.) Braided armouring ATEX ll 2 GD, Ex d llC / Ex e ll / Ex tD A21 IP68, IECEx Ex d IIC / Ex e ll IP protection without GWDR is IP 54. To achieve IP 66/68 protection, a nylon GWDR must be ordered separately. Ordering data Typ metric, nickel-plated brass KDSX M20 BS O NI 1 G16 KDSX M20 BS O NI 2 G16 KDSX M20 BS O NI 1 G20 KDSX M20 BS O NI 2 G20 KDSX M20 BS O NI 1 G20S KDSX M20 BS O NI 2 G20S KDSX M25 BS O NI 1 G25 KDSX M25 BS O NI 2 G25 KDSX M32 BS O NI 1 G32 KDSX M32 BS O NI 2 G32 KDSX M40 BS O NI 1 G40 KDSX M40 BS O NI 2 G40 KDSX M50 BS O NI 1 G50 KDSX M50 BS O NI 2 G50 KDSX M50 BS O NI 1 G50S KDSX M50 BS O NI 2 G50S KDSX M63 BS O NI 1 G63 KDSX M63 BS O NI 2 G63 KDSX M63 BS O NI 1 G63S KDSX M63 BS O NI 2 G63S KDSX M75 BS O NI 1 G75 KDSX M75 BS O NI 2 G75 KDSX M75 BS O NI 1 G75S KDSX M75 BS O NI 2 G75S Note 1420920000 – 2013 Thread D1 outer cable Ø D2 inner cable Ø Cable armour L/L1 SW MODR SUHB Qty. M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 25 / 1.5 M 25 / 1.5 M 32 / 1.5 M 32 / 1.5 M 40 / 1.5 M 40 / 1.5 M 50 / 1.5 M 50 / 1.5 M 50 / 1.5 M 50 / 1.5 M 63 / 1.5 M 63 / 1.5 M 63 / 1.5 M 63 / 1.5 M 75 / 1.5 M 75 / 1.5 M 75 / 1.5 M 75 / 1.5 4.90-10.00 8.40-13.50 12.00-17.60 15.50-21.10 9.40-12.50 11.50-16.00 16.80-23.90 20.30-27.40 23.20-30.50 26.70-34.00 28.60-36.20 33.00-40.60 41.10-48.50 45.70-53.20 34.80-42.40 39.40-46.70 53.80-61.20 58.40-65.80 47.50-54.80 52.10-59.50 66.50-73.40 71.10-78.00 60.20-68.00 64.80-72.20 4.00-8.40 4.00-8.40 6.70-14.00 6.70-14.00 8.00-11.70 8.00-11.70 13.00-20.00 13.00-20.00 19.00-26.30 19.00-26.30 25.00-32.20 25.00-32.20 36.50-44.10 36.50-44.10 31.50-38.20 31.50-38.20 49.50-65.00 49.50-65.00 42.50-50.10 42.50-50.10 60.50-68.00 60.50-68.00 54.50-62.00 54.50-62.00 0.15-0.35 0.15-0.35 0.15-0.5 0.15-0.5 0.15-0.35 0.15-0.35 0.15-0.5 0.15-0.5 0.15-0.55 0.15-0.55 0.2-0.6 0.2-0.6 0.2-0.8 0.2-0.8 0.2-0.6 0.2-0.6 0.3-0.8 0.3-0.8 0.3-0.8 0.3-0.8 0.3-1 0.3-1 0.3-1 0.3-1 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 58 / 16 65 / 16 65 / 16 72 / 16 72 / 16 73 / 16 73 / 16 73 / 16 73 / 16 76 / 19 76 / 19 76 / 19 76 / 19 82 / 19 82 / 19 82 / 19 82 / 19 24 24 30 30 24 24 38 38 46 46 55 55 65 65 65 65 80 80 80 80 90 90 90 90 32.5 32.5 32.5 32.5 32.5 32.5 47.5 47.5 55 55 65 65 80 80 80 80 95 95 95 95 110 110 110 110 L24 L24 L30 L30 L24 L24 L38 L38 L46 L46 L55 L55 L65 L65 L65 L65 L80 L80 L80 L80 L90 L90 L90 L90 20 20 20 20 20 20 20 20 10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 Order No. 1135910000 1135920000 1135950000 1135960000 1135930000 1135940000 1135970000 1135980000 1135990000 1136000000 1136010000 1136020000 1136050000 1136060000 1136030000 1136040000 1136090000 1136110000 1136070000 1136080000 1136140000 1136150000 1136120000 1136130000 • All cable glands have a thread pitch of 1.5 mm. • In the case of Ex d applications, the inner threads used for cable glands must meet the requirements of section 5.3 of EN/IEC 60079-1. In the screwed in position, at least 5 threads must be engaged. • If the cable glands are installed in non-metallic Ex e connection equipment, these must be connected to the protective earth of the system. • The connection cable must be laid securely and inflexibly to rule out tensile stress. C.41 Cable glands for Ex applications - Brass Cable entries Klippon® cable glands - Brass - Ex e, Ex d, IP 66 / IP 68 for non-armoured cables Cable gland exclusively for non-armoured cables and lines. L L1 Thread SW C Technical data Material O-ring / Seal insert Temperature range Degree of protection Water depth Approval Note Brass, nickel-plated CR / CR -20 °C...85 °C IP 66, IP 68 - 2.5 bar 25 m (30 Min.) ATEX ll 2 GD, Ex d llC / Ex e ll / Ex tD A21 IP68, IECEx Ex d IIC / Ex e ll Length „L“ varies according to cable diameter used. Ordering data Typ metric, brass KSG M20 BN O SC 2 G16 KSG M20 BN O SC 2 G20S KSG M20 BN O SC 2 G20 KSG M25 BN O SC 2 G25 KSG M32 BN O SC 2 G32 KSG M40 BN O SC 2 G40 KSG M50 BN O SC 2 G50S KSG M50 BN O SC 2 G50 KSG M63 BN O SC 2 G63S KSG M63 BN O SC 2 G63 KSG M75 BN O SC 2 G75 KSG M75 BN O SC 2 G75S metric, nickel-plated brass KSG M20 BN O NI 2 G16 KSG M20 BN O NI 2 G20S KSG M20 BN O NI 2 G20 KSG M25 BN O NI 2 G25 KSG M32 BN O NI 2 G32 KSG M40 BN O NI 2 G40 KSG M50 BN O NI 2 G50S KSG M50 BN O NI 2 G50 KSG M63 BN O NI 2 G63S KSG M63 BN O NI 2 G63 KSG M75 BN O NI 2 G75 KSG M75 BN O NI 2 G75S Note C.42 Thread KB L/L1 SW SUHB Qty. Order No. M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 25 / 1.5 M 32 / 1.5 M 40 / 1.5 M 50 / 1.5 M 50 / 1.5 M 63 / 1.5 M 63 / 1.5 M 75 / 1.5 M 75 / 1.5 4-8.4 7.2-11.7 9.6-14 13.5-20 19.5-26.3 23-32.2 28.2-38.2 33.2-44.1 39.3-50.1 46.7-56 58.1-68 52.3-62 33 / 16 33 / 16 33 / 16 33 / 16 33 / 16 37 / 16 37 / 16 37 / 16 37 / 19 37 / 19 37 / 19 37 / 19 25 25 30 38 46 55 65 65 80 80 90 90 L24 L24 L30 L38 L46 L55 L65 L65 L80 L80 L90 L90 20 20 20 20 10 10 1 1 1 1 1 1 1909380000 1909400000 1909410000 1909420000 1909430000 1909440000 1909450000 1909460000 1909470000 1909480000 1075340000 1075330000 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 25 / 1.5 M 32 / 1.5 M 40 / 1.5 M 50 / 1.5 M 50 / 1.5 M 63 / 1.5 M 63 / 1.5 M 75 / 1.5 M 75 / 1.5 4-8.4 7.2-11.7 9.6-14 13.5-20 19.5-26.3 23-32.2 28.2-38.2 33.2-44.1 39.3-50.1 46.7-56 58.1-68 52.3-62 33 / 16 33 / 16 33 / 16 33 / 16 33 / 16 37 / 16 37 / 16 37 / 16 37 / 19 37 / 19 37 / 19 37 / 19 25 25 30 38 46 55 65 65 80 80 90 90 L24 L24 L30 L38 L46 L55 L65 L65 L80 L80 L90 L90 20 20 20 20 10 10 1 1 1 1 1 1 1911510000 1911540000 1911560000 1911570000 1911580000 1911590000 1911600000 1911610000 1911620000 1911630000 1075360000 1075350000 • All cable glands have a thread pitch of 1.5 mm. • In the case of Ex d applications, the inner threads used for cable glands must meet the requirements of section 5.3 of EN/IEC 60079-1. In the screwed in position, at least 5 threads must be engaged. • If the cable glands are installed in non-metallic Ex e connection equipment, these must be connected to the protective earth of the system. • The connection cable must be laid securely and inflexibly to rule out tensile stress. 1420920000 – 2013 Cable glands for Ex applications - Brass Cable entries Klippon® cable glands - Brass - Ex e, Ex d, IP 66 / IP 68 for non-armoured cables Cable gland exclusively for non-armoured cables and lines. L L1 Thread SW C Technical data Material O-ring / Seal insert Temperature range Degree of protection Water depth Approval Brass Silicone / Silicone -60 °C...180 °C IP 66, IP 68 - 2.5 bar 25 m (30 Min.) ATEX ll 2 GD, Ex d llC / Ex e ll / Ex tD A21 IP68, IECEx Ex d IIC / Ex e ll Note Ordering data Typ metric, brass KSG M20 BS O SC 2 G16 KSG M20 BS O SC 2 G20 KSG M20 BS O SC 2 G20S KSG M25 BS O SC 2 G25 KSG M32 BS O SC 2 G32 KSG M40 BS O SC 2 G40 KSG M50 BS O SC 2 G50 KSG M50 BS O SC 2 G50S KSG M63 BS O SC 2 G63 KSG M63 BS O SC 2 G63S KSG M75 BS O SC 2 G75 KSG M75 BS O SC 2 G75S metric, nickel-plated brass KSG M20 BS O NI 2 G16 KSG M20 BS O NI 2 G20 KSG M20 BS O NI 2 G20S KSG M25 BS O NI 2 G25 KSG M32 BS O NI 2 G32 KSG M40 BS O NI 2 G40 KSG M50 BS O NI 2 G50 KSG M50 BS O NI 2 G50S KSG M63 BS O NI 2 G63 KSG M63 BS O NI 2 G63S KSG M75 BS O NI 2 G75 KSG M75 BS O NI 2 G75S Note 1420920000 – 2013 Thread KB L/L1 SW SUHB Qty. Order No. M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 25 / 1.5 M 32 / 1.5 M 40 / 1.5 M 50 / 1.5 M 50 / 1.5 M 63 / 1.5 M 63 / 1.5 M 75 / 1.5 M 75 / 1.5 4-8.4 9.6-14 7.2-11.7 13.5-20 19.5-26.3 23-32.2 33.2-44.1 28.2-38.2 46.7-56 39.3-50.1 58.1-68 52.3-62 33 / 16 33 / 16 33 / 16 33 / 16 33 / 16 37 / 16 37 / 16 37 / 16 37 / 19 37 / 19 37 / 19 37 / 19 25 30 25 38 46 55 65 65 80 80 90 90 L24 L30 L24 L38 L46 L55 L65 L65 L80 L80 L90 L90 20 20 20 20 10 10 1 1 1 1 1 1 0930481212 0930501212 1136720000 0930511212 0930521212 0930531212 0930551212 1136730000 1136750000 1136740000 1136770000 1136760000 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 25 / 1.5 M 32 / 1.5 M 40 / 1.5 M 50 / 1.5 M 50 / 1.5 M 63 / 1.5 M 63 / 1.5 M 75 / 1.5 M 75 / 1.5 4-8.4 9.6-14 7.2-11.7 13.5-20 19.5-26.3 23-32.2 33.2-44.1 28.2-38.2 46.7-56 39.3-50.1 58.1-68 52.3-62 33 / 16 33 / 16 33 / 16 33 / 16 33 / 16 37 / 16 37 / 16 37 / 16 37 / 19 37 / 19 37 / 19 37 / 19 25 25 25 38 46 55 65 65 80 80 90 90 L24 L30 L24 L38 L46 L55 L65 L65 L80 L80 L90 L90 20 20 20 20 10 10 1 1 1 1 1 1 0930481222 0930501222 0930491224 0930511222 0930521222 0930531222 1136670000 1136660000 1136690000 1136680000 1136710000 1136700000 • All cable glands have a thread pitch of 1.5 mm. • In the case of Ex d applications, the inner threads used for cable glands must meet the requirements of section 5.3 of EN/IEC 60079-1. In the screwed in position, at least 5 threads must be engaged. • If the cable glands are installed in non-metallic Ex e connection equipment, these must be connected to the protective earth of the system. • The connection cable must be laid securely and inflexibly to rule out tensile stress. C.43 Cable glands for Ex applications - Brass Cable entries Klippon® cable glands - Brass - Ex d, IP 68 for armoured and non-armoured encapsulated cables D1 SW Barrier cable glands for cables and lines with a single-wire, metal-foil armouring, and braided armouring for Ex-d IIC enclosure, with a volume of more than two litres. D2 C L1 L Technical data Material O-ring / Seal insert Temperature range Degree of protection Water depth Type of armouring Encapsulation compound Approval Note Brass Silicone / CR -60 °C...85 °C IP 68 - 10 bar 100 m (30 Min.) Single-wire armouring, Metal foil armouring, Braided armouring Processing temperature at 21°C, the sealing compound is hardened after one hour, After 4 hours, the cable gland can be installed and initial commissioning can take place ATEX ll 2 GD, Ex d llC / Ex tD A21 IP68, l M2 Ex d l, IECEx Ex d llC / Ex d l Ordering data Typ metric, brass KUB M20 BS O SC 1 G16 KUB M20 BS O SC 2 G16 KUB M20 BS O SC 1 G20S KUB M20 BS O SC 2 G20S KUB M20 BS O SC 1 G20 KUB M20 BS O SC 2 G20 KUB M25 BS O SC 1 G25 KUB M25 BS O SC 2 G25 KUB M32 BS O SC 1 G32 KUB M32 BS O SC 2 G32 KUB M40 BS O SC 1 G40 KUB M40 BS O SC 2 G40 KUB M50 BS O SC 1 G50S KUB M50 BS O SC 2 G50S KUB M50 BS O SC 1 G50 KUB M50 BS O SC 2 G50 KUB M63 BS O SC 1 G63S KUB M63 BS O SC 2 G63S KUB M63 BS O SC 1 G63 KUB M63 BS O SC 2 G63 KUB M75 BS O SC 1 G75S KUB M75 BS O SC 2 G75S KUB M75 BS O SC 1 G75 KUB M75 BS O SC 2 G75 Note C.44 Thread D1 outer cable Ø D2 inner cable Ø L/L1 SW SUHB Qty. M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 25 / 1.5 M 25 / 1.5 M 32 / 1.5 M 32 / 1.5 M 40 / 1.5 M 40 / 1.5 M 50 / 1.5 M 50 / 1.5 M 50 / 1.5 M 50 / 1.5 M 63 / 1.5 M 63 / 1.5 M 63 / 1.5 M 63 / 1.5 M 75 / 1.5 M 75 / 1.5 M 75 / 1.5 M 75 / 1.5 6.70-16.00 9.00-17.60 9.40-10.30 11.50-21.10 12.00-13.50 15.50-12.50 16.80-23.90 20.30-27.40 23.20-30.50 26.70-34.00 28.60-36.20 33.00-46.70 34.80-48.50 39.40-59.50 41.10-40.60 45.70-42.40 47.50-61.20 52.10-72.20 53.80-53.20 58.40-54.80 60.20-73.40 64.80-78.00 66.50-65.80 71.10-68.00 14.00 11.70 11.70 11.70 11.70 14.00 20.00 20.00 26.30 26.30 32.20 38.20 44.10 50.10 32.20 38.20 56.00 62.00 44.10 50.10 68.00 68.00 56.00 62.00 72 / 16 72 / 16 72 / 16 72 / 16 73 / 16 73 / 16 83 / 16 83 / 16 103 / 16 103 / 16 105 / 16 105 / 16 115 / 16 115 / 16 115 / 16 115 / 16 115 / 19 115 / 19 115 / 19 115 / 19 122 / 19 122 / 19 122 / 19 122 / 19 24 24 24 24 30 30 38 38 46 46 55 55 65 65 65 65 80 80 80 80 90 90 90 90 L24 L24 L24 L24 EL30 EL30 EL38 EL38 EL46 EL46 EL55 EL55 EL65 EL65 EL65 EL65 EL80 EL80 EL80 EL80 EL90 EL90 EL90 EL90 20 20 20 20 20 20 20 20 10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 Order No. 1095340000 1095350000 1095360000 1095370000 1095380000 1095390000 1095400000 1095410000 1095420000 1095430000 1095440000 1095450000 1095460000 1095470000 1095480000 1095490000 1095500000 1095510000 1095520000 1095530000 1095540000 1095550000 1095560000 1095570000 • All cable glands have a thread pitch of 1.5 mm. • In the case of Ex d applications, the inner threads used for cable glands must meet the requirements of section 5.3 of EN/IEC 60079-1. In the screwed in position, at least 5 threads must be engaged. • The connection cable must be laid securely and inflexibly to rule out tensile stress. 1420920000 – 2013 Cable glands for Ex applications - Brass Cable entries Klippon® cable glands - Brass - Ex d, IP 68 for armoured and non-armoured encapsulated cables D1 SW Barrier cable glands for cables and lines with a single-wire, metal-foil armouring, and braided armouring for Ex-d IIC enclosure, with a volume of more than two litres. D2 C L1 L Technical data Material O-ring / Seal insert Temperature range Degree of protection Water depth Type of armouring Encapsulation compound Approval Note Brass, nickel-plated Silicone / Silicone -60 °C...85 °C IP 68 - 10 bar 100 m (30 Min.) Single-wire armouring, Metal foil armouring, Braided armouring Processing temperature at 21°C, the sealing compound is hardened after one hour, After 4 hours, the cable gland can be installed and initial commissioning can take place ATEX ll 2 GD, Ex d llC / Ex tD A21 IP68, l M2 Ex d l, IECEx Ex d llC / Ex d l Ordering data Typ metric, nickel-plated brass KUB M20 BS O NI 1 G16 KUB M20 BS O NI 2 G16 KUB M20 BS O NI 1 G20 KUB M20 BS O NI 2 G20 KUB M20 BS O NI 1 G20S KUB M20 BS O NI 2 G20S KUB M25 BS O NI 1 G25 KUB M25 BS O NI 2 G25 KUB M32 BS O NI 1 G32 KUB M32 BS O NI 2 G32 KUB M40 BS O NI 1 G40 KUB M40 BS O NI 2 G40 KUB M50 BS O NI 1 G50 KUB M50 BN O NI 2 G50 KUB M50 BS O NI 1 G50S KUB M50 BS O NI 2 G50S KUB M63 BS O NI 1 G63 KUB M63 BS O NI 2 G63 KUB M63 BS O NI 1 G63S KUB M63 BS O NI 2 G63S KUB M75 BS O NI 1 G75 KUB M75 BS O NI 2 G75 KUB M75 BS O NI 1 G75S KUB M75 BS O NI 2 G75S Note 1420920000 – 2013 Thread D1 outer cable Ø D2 inner cable Ø L/L1 SW SUHB Qty. M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 20 / 1.5 M 25 / 1.5 M 25 / 1.5 M 32 / 1.5 M 32 / 1.5 M 40 / 1.5 M 40 / 1.5 M 50 / 1.5 M 50 / 1.5 M 50 / 1.5 M 50 / 1.5 M 63 / 1.5 M 63 / 1.5 M 63 / 1.5 M 63 / 1.5 M 75 / 1.5 M 75 / 1.5 M 75 / 1.5 M 75 / 1.5 6.70-10.30 9.00-13.50 12.00-17.60 15.50-21.10 9.40-12.50 11.50-16.00 16.80-23.90 20.30-27.40 23.20-30.50 26.70-34.00 28.60-36.20 33.00-40.60 41.10-48.50 45.70-53.20 34.80-42.40 39.40-46.70 53.80-61.20 58.40-65.80 47.50-54.80 52.10-59.50 66.50-73.40 71.10-78.00 60.20-68.00 64.80-72.20 11.70 11.70 11.70 11.70 14.00 14.00 20.00 20.00 26.30 26.30 32.20 32.20 44.10 44.10 38.20 38.20 56.00 56.00 50.10 50.10 68.00 68.00 62.00 62.00 72 / 16 72 / 16 73 / 16 73 / 16 72 / 16 72 / 16 83 / 16 83 / 16 103 / 16 103 / 16 105 / 16 105 / 16 115 / 16 115 / 16 115 / 16 115 / 16 115 / 19 115 / 19 115 / 19 115 / 19 122 / 19 122 / 19 122 / 19 122 / 19 24 24 30 30 24 24 38 38 46 46 55 55 65 65 65 65 80 80 80 80 90 90 90 90 L24 L24 EL30 EL30 L24 L24 EL38 EL38 EL46 EL46 EL55 EL55 EL65 EL65 EL65 EL65 EL80 EL80 EL80 EL80 EL90 EL90 EL90 EL90 20 20 20 20 20 20 20 20 10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 Order No. 1095100000 1095110000 1095140000 1095150000 1095120000 1095130000 1095160000 1095170000 1095180000 1095190000 1095200000 1095210000 1095240000 1095250000 1095220000 1095230000 1095280000 1095290000 1095260000 1095270000 1095320000 1095330000 1095300000 1095310000 • All cable glands have a thread pitch of 1.5 mm. • In the case of Ex d applications, the inner threads used for cable glands must meet the requirements of section 5.3 of EN/IEC 60079-1. In the screwed in position, at least 5 threads must be engaged. • The connection cable must be laid securely and inflexibly to rule out tensile stress. C.45 Accessories - Lock nuts Cable entries Lock nuts - Plastic 7035 Lock nuts with collar for preventing enclosure damage on installation. These are used to secure plastic cable glands and sealing plugs. S1 C Thread Technical data Material / Colour Temperature range Flammability rating Polyamid 6 (PA6 - GF30) / RAL 7035 -20 °C...80 °C V-2 Note Ordering data Typ metric SKMU M12 - K GR SKMU M16 - K GR SKMU M20 - K GR SKMU M25 - K GR SKMU M32 - K GR SKMU M40 - K GR SKMU M50 - K GR SKMU M63 - K GR PG SKMU PG7-K GR SKMU PG9-K GR SKMU PG11-K GR SKMU PG 13.5-K GR SKMU PG16-K GR SKMU PG21-K GR SKMU PG29-K GR SKMU PG36-K GR SKMU PG42-K GR SKMU PG48-K GR Note C.46 Thread S1 SW Qty. Order No. M 12 / 1.5 M 16 / 1.5 M 20 / 1.5 M 25 / 1.5 M 32 / 1.5 M 40 / 1.5 M 50 / 1.5 M 63 / 1.5 5.00 5.00 6.00 6.00 7.00 7.00 8.00 8.00 18 22 26 32 41 50 60 75 100 100 100 100 100 50 10 10 1772440000 1772450000 1772460000 1772470000 1772480000 1772490000 1772500000 1772510000 PG 7 PG 9 PG 11 PG 13.5 PG 16 PG 21 PG 29 PG 36 PG 42 PG 48 5.00 5.00 5.00 6.00 6.00 7.00 7.00 8.00 8.00 8.00 19 22 24 27 30 36 46 60 65 70 100 100 100 100 100 100 50 25 25 25 1697440000 1697450000 1697460000 1697470000 1697480000 1698220000 1698230000 1698240000 1698250000 1719090000 Further versions on request 1420920000 – 2013 Accessories - Lock nuts Cable entries Lock nuts - Plastic 9005 Lock nuts with collar for preventing enclosure damage on installation. These are used to secure plastic cable glands and sealing plugs - recommended for Ex e and Ex i plastic cable glands. S1 C Thread Technical data Material / Colour Temperature range Flammability rating Polyamid 6 (PA6 - GF30) / RAL 9005 -20 °C...80 °C V-2 Note Ordering data Typ metric SKMU M12-K SW SKMU M16 K SW SKMU M20 K SW SKMU M25 K SW SKMU M32 K SW SKMU M40 K SW SKMU M50 K SW SKMU M63 K SW PG SKMU PG7-K SW SKMU PG9-K SW SKMU PG11-K SW SKMU PG13.5-K SW SKMU PG16-K SW SKMU PG21-K SW SKMU PG29-K SW SKMU PG36-K SW SKMU PG42-K SW SKMU PG48-K SW Note 1420920000 – 2013 Thread S1 SW Qty. Order No. M 12 / 1.5 M 16 / 1.5 M 20 / 1.5 M 25 / 1.5 M 32 / 1.5 M 40 / 1.5 M 50 / 1.5 M 63 / 1.5 5.00 5.00 6.00 6.00 7.00 7.00 8.00 8.00 18 22 26 32 41 50 60 75 100 100 100 25 100 10 5 5 1806540000 1736920000 1736930000 1736940000 1736950000 1736960000 1736970000 1736980000 PG 7 PG 9 PG 11 PG 13.5 PG 16 PG 21 PG 29 PG 36 PG 42 PG 48 5.00 5.00 5.00 6.00 6.00 7.00 7.00 8.00 8.00 8.00 19 22 24 27 30 36 46 60 65 70 50 50 50 50 25 20 20 10 10 5 1719100000 1719110000 1719120000 1719130000 1719140000 1719150000 1719160000 1719170000 1719180000 1719190000 C.47 Accessories - Lock nuts Cable entries Lock nuts - Brass - Nickel-plated S1 A lock nut is used to secure the brass cable glands and sealing plugs – also recommended when working with Ex applications. C Thread Technical data Material Brass, nickel-plated Note Ordering data Typ metric SKMU M12 - MS SKMU M16 MS SKMU M20 MS SKMU M25 MS SKMU M32 MS SKMU M40 MS SKMU M50 MS SKMU M63 MS SKMU M75 MS PG SKMU PG7-MS SKMU PG9-MS SKMU PG11-MS SKMU PG13.5-MS SKMU PG16-MS SKMU PG21-MS SKMU PG29-MS SKMU PG36-MS SKMU PG42-MS SKMU PG48-MS Note C.48 Thread S1 SW Qty. Order No. M 12 / 1.5 M 16 / 1.5 M 20 / 1.5 M 25 / 1.5 M 32 / 1.5 M 40 / 1.5 M 50 / 1.5 M 63 / 1.5 M 75 / 1.5 2.8 2.8 3 3 4 4.5 5 6 8 14 19 24 28 36 44 54 70 85 50 50 50 25 20 10 5 5 5 1772360000 1736990000 1737000000 1737010000 1737020000 1737030000 1737040000 1737050000 1737060000 PG 7 PG 9 PG 11 PG 13.5 PG 16 PG 21 PG 29 PG 36 PG 42 PG 48 2.8 2.8 3 3 3 3.5 4 5 5 5.5 15 18 21 23 26 32 41 51 60 64 100 100 100 100 100 50 50 50 50 50 1694070000 1694080000 1694090000 1694100000 1694110000 1719200000 1719210000 1719220000 1719230000 1719240000 Further versions on request 1420920000 – 2013 Accessories - Lock nuts Cable entries Lock nuts - Brass - Natural S1 A lock nut made from untreated brass is used to secure the brass cable glands and sealing plugs – also recommended when working with Ex applications. C Thread Technical data Material Brass Note Ordering data Typ metric SKMU M16 MS SC SKMU M20 MS SC SKMU M25 MS SC SKMU M32 MS SC SKMU M40 MS SC SKMU M50 MS SC SKMU M63 MS SC SKMU M75 MS SC SKMU M80 MS SC SKMU M85 MS SC SKMU M90 MS SC Note 1420920000 – 2013 Thread S1 SW Qty. M 16 / 1.5 M 20 / 1.5 M 25 / 1.5 M 32 / 1.5 M 40 / 1.5 M 50 / 1.5 M 63 / 1.5 M 75 / 1.5 M 80 / 1.5 M 85 / 1.5 M 90 / 1.5 4 4 4 4 4.5 5 6.5 7 7 7 7 22 24 30 40 50 65 75 90 90 104.8 104.8 50 50 25 20 10 5 5 5 5 5 5 Order No. 0930640001 0930640002 0930640003 0930640004 0930640005 0930640006 0930640007 0930640008 0930640009 0930640010 0930640011 C.49 Accessories - Lock nuts Cable entries Lock nuts - Brass - EMC S1 S2 Serrated locks are used for securing brass cable glands and sealing plugs – specially equipped with 6 edges which contact the enclosure when the lock nut is tightened. C Thread Technical data Material Brass, nickel-plated Note Ordering data Typ metric SKMU EMV M12 SKMU EMV M16 SKMU EMV M20 SKMU EMV M25 SKMU EMV M32 SKMU EMV M40 SKMU EMV M50 SKMU EMV M63 PG SKMU EMV PG7 SKMU EMV PG9 SKMU EMV PG11 SKMU EMV PG13.5 SKMU EMV PG16 SKMU EMV PG21 SKMU EMV PG29 SKMU EMV PG 36 SKMU EMV PG 42 SKMU EMV PG 48 Note C.50 Thread S1 SW Qty. Order No. M 12 / 1.5 M 16 / 1.5 M 20 / 1.5 M 25 / 1.5 M 32 / 1.5 M 40 / 1.5 M 50 / 1.5 M 63 / 1.5 3.6 3.6 3.6 3.6 4.1 4.6 4.6 6.6 15 19 24 30 36 46 60 70 50 50 50 20 20 10 10 10 1777610000 1777620000 1777630000 1777640000 1777650000 1777660000 1777670000 1777680000 PG 7 PG 9 PG 11 PG 13.5 PG 16 PG 21 PG 29 PG 36 PG 42 PG 48 4.7 4.7 4.7 4.7 4.7 5.2 5.7 4.6 4.6 5.6 15 18 21 23 26 32 41 51 58 64 20 20 20 10 10 10 15 1 1 1 1718900000 1718910000 1718920000 1718930000 1718940000 1718950000 1718960000 1777710000 1777700000 1777690000 Further versions on request 1420920000 – 2013 Accessories - Flat IP washer Cable entries Flat IP washer - Standard - Polyethylene Flat IP washer for increasing the degree of protection for cable glands and sealing plugs. The IP washer is also suitable as a replacement for O-rings. D1 D2 S C Technical data Material / Colour Temperature range Polyethylene / Transparent -30 °C...90 °C Note Ordering data Typ metric GWDR M12-PO GWDR M16-PO GWDR M20-PO GWDR M25-PO GWDR M32-PO GWDR M40-PO GWDR M50-PO GWDR M63-PO PG GWDR PG7-PO GWDR PG9-PO GWDR PG11-PO GWDR PG13.5-PO GWDR PG16-PO GWDR PG21-PO GWDR PG29-PO GWDR PG36-PO GWDR PG42-PO GWDR PG48-PO Note 1420920000 – 2013 Thread D1 D2 S Qty. Order No. M 12 / 1.5 M 16 / 1.5 M 20 / 1.5 M 25 / 1.5 M 32 / 1.5 M 40 / 1.5 M 50 / 1.5 M 63 / 1.5 16.00 20.00 25.00 30.00 38.00 45.00 56.00 70.00 12.00 16.00 20.40 25.00 32.00 40.00 50.00 63.00 1.50 1.50 2.00 2.00 2.00 2.00 2.00 2.00 50 50 100 50 50 50 50 50 1777920000 1777930000 1777940000 1777950000 1777960000 1777970000 1777980000 1777990000 PG 7 PG 9 PG 11 PG 13.5 PG 16 PG 21 PG 29 PG 36 PG 42 PG 48 16.50 19.00 22.50 25.00 27.00 33.50 43.50 55.00 63.00 69.00 12.50 15.20 18.60 20.40 22.50 28.30 37.00 47.00 54.00 59.30 1.60 1.60 1.80 1.80 1.80 2.20 2.20 2.70 3.20 3.20 100 100 100 100 100 100 50 50 10 5 1719440000 1719450000 1719460000 1719470000 1719480000 1719490000 1719500000 1719510000 1719520000 1719530000 Further versions on request C.51 Accessories - Flat IP washer Cable entries Flat gasket seals - Standard - Neoprene Flat gasket seal to increase the degree of protection for cable glands and sealing plugs – recommended for use in Ex applications. The seal is also suitable as a replacement for O-rings. D1 D2 S C Technical data Material / Colour Temperature range Neoprene / RAL 9005 -30 °C...100 °C Note Ordering data Typ metric GWDR M12-NP GWDR M16-NP GWDR M20-NP GWDR M25-NP GWDR M32-NP GWDR M40-NP GWDR M50-NP GWDR M63-NP PG GWDR PG7-NP GWDR PG9-NP GWDR PG11-NP GWDR PG13.5-NP GWDR PG16-NP GWDR PG21-NP GWDR PG29-NP GWDR PG36-NP GWDR PG42-NP GWDR PG48-NP Note C.52 Thread D1 D2 S Qty. Order No. M 12 / 1.5 M 16 / 1.5 M 20 / 1.5 M 25 / 1.5 M 32 / 1.5 M 40 / 1.5 M 50 / 1.5 M 63 / 1.5 18.00 22.00 24.00 30.00 42.00 52.00 63.00 77.00 12.00 16.00 20.00 25.00 32.00 40.00 50.00 63.00 1.20 1.20 1.20 1.50 1.50 1.50 1.50 2.00 50 50 50 50 50 20 20 10 1913320000 1736230000 1736240000 1736250000 1736260000 1736270000 1736280000 1736290000 PG 7 PG 9 PG 11 PG 13.5 PG 16 PG 21 PG 29 PG 36 PG 42 PG 48 17.00 21.00 24.00 27.00 30.00 35.00 45.00 60.00 65.00 71.00 11.60 14.00 17.00 19.50 22.50 28.30 37.00 47.00 54.00 59.30 1.20 1.20 1.20 1.20 1.20 1.50 1.50 1.50 1.50 1.50 100 100 100 100 100 100 50 20 10 5 1719540000 1719550000 1719560000 1719570000 1719580000 1719590000 1719600000 1719610000 1719620000 1719630000 Further versions on request 1420920000 – 2013 Accessories - Flat IP washer Cable entries Flat IP washer - Standard - Nylon Flat nylon IP washer, used for sealing large surfaces, for example around cable glands on enclosures. D1 D2 S C Technical data Material / Colour Temperature range Nylon 6 / RAL 3020 -40 °C...135 °C Note Ordering data Typ metric KSWN M16 KSWN M20 KSWN M25 KSWN M32 KSWN M40 KSWN M50 KSWN M63 KSWN M75 Note 1420920000 – 2013 Thread D1 D2 S Qty. M 16 / 1.5 M 20 / 1.5 M 25 / 1.5 M 32 / 1.5 M 40 / 1.5 M 50 / 1.5 M 63 / 1.5 M 75 / 1.5 25.00 29.40 38.10 42.50 52.00 65.00 79.40 90.50 16.50 20.70 25.70 32.50 40.50 50.50 63.50 75.50 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.00 25 25 25 25 25 25 25 25 Order No. 1076630000 0930730002 1076640000 1076650000 0899780000 0900660000 1076660000 1076670000 C.53 Accessories - Flat IP washer Cable entries Flat IP washer - Standard - Vulcanised fibre Flat nylon IP washer made from vulcanised fibre, used for sealing large surfaces, for example around cable glands on enclosures. D1 D2 S C Technical data Material / Colour Temperature range Vulcanized fibre / RAL 3011 -40 °C...95 °C Note Ordering data Typ metric KSWF M16 KSWF M20 KSWF M25 KSWF M32 KSWF M40 KSWF M50 KSWF M63 KSWF M75 KSWF M90 Note C.54 Thread D1 D2 S Qty. M 16 / 1.5 M 20 / 1.5 M 25 / 1.5 M 32 / 1.5 M 40 / 1.5 M 50 / 1.5 M 63 / 1.5 M 75 / 1.5 M 90 / 1.5 25.00 29.40 38.10 42.50 52.00 65.00 79.40 90.50 114.30 16.50 20.70 25.70 32.50 40.50 50.50 63.50 75.50 90.50 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.00 25 25 25 25 25 25 25 25 25 Order No. 1076680000 0899750000 0899770000 1076690000 1076710000 1076720000 1076730000 1076740000 1192820000 1420920000 – 2013 Accessories - Earthing rings Cable entries Accessories - Earth tags - Brass - Nickel plated Earth tags are best used when a cable shielding is being tightened onto the cable gland, and when it has the same potential as another cable gland on the enclosure. A Ø D1 C C Ø D2 B Ø Thread Technical data Material Brass, nickel-plated Note Ordering data Typ metric EA-RING MS/M 16 EA-RING MS/M 20 EA-RING MS/M 25 EA-RING MS/M 32 EA-RING MS/M 40 EA-RING MS/M 50 EA-RING MS/M 63 EA-RING MS/M 75 Note 1420920000 – 2013 Thread A B C D1 D2 Qty. M 16 / 1.5 M 20 / 1.5 M 25 / 1.5 M 32 / 1.5 M 40 / 1.5 M 50 / 1.5 M 63 / 1.5 M 75 / 1.5 48.75 53.8 61.5 73 86.5 111.5 125.5 137.5 30.00 33.00 36.00 41.00 44.50 58.00 67.00 73.00 13.00 13.00 17.00 22.00 30.00 40.00 40.00 40.00 24.50 28.60 34.00 42.00 54.00 67.00 77.00 89.00 6.75 7.00 10.50 12.20 13.50 13.50 13.50 13.50 20 20 20 20 10 10 10 10 Order No. 1736480000 1736490000 1736500000 1736510000 1736520000 1736530000 1736540000 1736550000 Further versions on request C.55 Accessories - Earthing rings Cable entries Accessories - Earth tags - Brass - Natural Earth tags are best used when a cable shielding is being tightened onto the cable gland, and when it has the same potential as another cable gland on the enclosure. A Ø D2 C C Ø D1 Ø Thread B Technical data Material Brass Note Ordering data Typ metric EA-RING MS/M16 SC EA-RING MS/M20 SC EA-RING MS/M25 SC EA-RING MS/M32 SC EA-RING MS/M40 SC EA-RING MS/M50 SC EA-RING MS/M63 SC EA-RING MS/M75 SC Note C.56 Thread A B C D1 D2 Qty. M 16 / 1.5 M 20 / 1.5 M 25 / 1.5 M 32 / 1.5 M 40 / 1.5 M 50 / 1.5 M 63 / 1.5 M 75 / 1.5 50.8 54 60.2 74.6 86.7 111 128.7 141.3 31.80 33.00 36.50 42.50 45.50 58.10 66.80 73.00 12.80 12.80 12.80 22.30 31.70 41.30 41.30 41.30 16.30 21.80 27.30 33.80 42.70 50.70 63.50 76.30 6.90 6.90 6.90 11.80 13.50 13.50 13.50 13.50 20 20 20 20 10 10 10 10 Order No. 0930710001 0930710002 0930710003 0930710004 0930710005 0930710006 0930710007 0930710008 Other versions on request 1420920000 – 2013 Accessories - Shrouds Cable entries Accessories - Shrouds - PVC The cover shroud a cable gland before and after the installation. It also protects against external environmental influences. A S C D1 B Technical data Material / Colour Temperature range Hardness [Shore A] PVC / RAL 9005 -25 °C...70 °C 65 Note Ordering data Typ metric KSP L24 KSP L30 KSP L38 KSP L46 KSP L55 KSP L65 KSP L80 KSP L90 KSP EL30* KSP EL38* KSP EL46* KSP EL55* KSP EL65* KSP EL80* KSP EL90* Note 1420920000 – 2013 A B D1 S Qty. 120 110 160 160 160 210 240 240 127.5 168 198 210 250 270 285 70.00 55.00 60.00 60.00 60.00 70.00 90.00 90.00 75.00 80.00 95.00 105.00 115.00 115.00 120.00 25.00 30.00 37.00 46.00 55.00 65.00 80.00 90.00 30.00 38.00 46.00 55.00 65.00 80.00 90.00 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50 2.00 2.00 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 Order No. 1736570000 1736580000 1736590000 1736600000 1736610000 1736620000 1736630000 1736640000 1736670000 1736680000 1076750000 1076760000 1076770000 1076780000 1076790000 *These shrouds have been specially designed for the Klippon® KDSU and Klippon® KUB cable glands. C.57 Accessories - Shrouds Cable entries Accessories - Shrouds - Silicone The cover shroud a cable gland before and after the installation. It also protects against external environmental influences. S D1 C B A Technical data Material / Colour Temperature range Hardness [IRHD] Silicone / RAL 5015 -60 °C...200 °C 65 Note Ordering data Typ metric KSP L24 S KSP L30 S KSP L38 S KSP L46 S KSP L55 S KSP L65 S KSP L80 S KSP L90 S KSP L 104 S KSP L114 S Note C.58 A B D1 S Qty. 80 80 85 95 95 110 120 140 160 180 60.00 60.00 65.00 70.00 70.00 80.00 90.00 110.00 130.00 150.00 25.00 30.00 37.00 46.00 55.00 65.00 80.00 90.00 104.00 114.00 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50 10 10 10 10 10 10 10 10 10 10 Order No. 0930700001 0930700002 0930700003 0930700004 0930700005 0930700006 0930700007 0930700008 1193940000 1192790000 1420920000 – 2013 Accessories - Washers Cable entries Accessories - Serrated washers, Stainless steel Serrated stainless steel washers to prevent mounted cable glands from loosening. D2 C D1 Technical data Material Stainless steel 1.4404 (316L) Note Ordering data Typ metric SZS M16 SZS M20 SZS M25 SZS M32 SZS M40 SZS M50 SZS M63 Note 1420920000 – 2013 Thread D1 D2 Qty. M 16 / 1.5 M 20 / 1.5 M 25 / 1.5 M 32 / 1.5 M 40 / 1.5 M 50 / 1.5 M 63 / 1.5 25.50 32.40 37.40 48.00 60.00 71.00 87.00 17.30 21.30 25.30 33.00 41.00 51.00 64.00 50 10 10 20 5 5 5 Order No. 1736300000 1736310000 1736320000 1736330000 1736340000 1736350000 1736360000 C.59 Sealing plugs Cable entries Sealing plugs - Plastic Plastic sealing plug with cross-head is used to seal surplus threaded holes and to maintain the IP protection degree. L ø L1 C Thread Technical data Material / Colour Temperature range Protection degree Flammability rating Note Polyamid 6 (PA6 - GF30) / RAL 7035 -40 °C...100 °C IP 54 V-2 Optional sealing ring Ordering data Typ metric VP M12 K54 VP M16 K54 VP M20 K54 VP M25 K54 VP M32 K54 VP M40 K54 VP M50 K54 VP M63 K54 PG VP 7-K54 VP 9-K54 VP 11-K54 VP 13.5-K54 VP 16-K54 VP 21-K54 VP 29-K54 VP 36-K54 VP 42-K54 VP 48-K54 Note C.60 Thread L L1 Head Ø Qty. Order No. M 12 / 1.5 M 16 / 1.5 M 20 / 1.5 M 25 / 1.5 M 32 / 1.5 M 40 / 1.5 M 50 / 1.5 M 63 / 1.5 5.5 5.5 6.5 7 7 7 8.5 8.5 6 7 7 10 11 13 14 15 15.00 20.00 24.00 30.00 37.00 46.00 56.00 69.50 100 100 100 100 100 50 25 50 1776930000 1776920000 1776910000 1776900000 1776940000 1776950000 1776960000 1776970000 PG 7 PG 9 PG 11 PG 13.5 PG 16 PG 21 PG 29 PG 36 PG 42 PG 48 8 9.5 10 10 10 12 11.5 14 14 16 6 5 6.5 5 5 8 8 10 10 12 15.00 19.00 22.00 25.00 27.00 33.00 44.00 55.00 62.00 69.00 50 100 100 100 100 100 50 25 10 5 1719250000 0294760000 0294860000 0294960000 0295060000 0295160000 0501160000 0501260000 0501360000 1719260000 Other versions available on request. The sealing plugs must be tightened „hand-tight“ with the screwdriver. 1420920000 – 2013 Sealing plugs Cable entries Sealing plugs - Brass - Nickel-plated Brass sealing plug with cross-head is used to seal surplus threaded holes and to maintain the IP protection degree. L1 L ø C Thread Technical data Material O-Ring Temperature range Protection degree Brass, nickel-plated NBR -40 °C...100 °C IP 68 Note Ordering data Typ metric VP M12-MS65 VP M16-MS65 VP M20-MS65 VP M25-MS65 VP M32-MS65 VP M40-MS65 VP M50-MS65 VP M63-MS65 PG VP 7-MS65 VP 9-MS65 VP 11-MS65 VP 13.5-MS65 VP 16-MS65 VP 21-MS65 VP 29-MS65 VP 36-MS65 VP 42-MS65 VP 48-MS65 Note 1420920000 – 2013 Thread L L1 Head Ø Qty. Order No. M 12 / 1.5 M 16 / 1.5 M 20 / 1.5 M 25 / 1.5 M 32 / 1.5 M 40 / 1.5 M 50 / 1.5 M 63 / 1.5 5 8 9.5 11 12 13 15 16 5 5 6.5 7 8 8 9 10 14.00 18.00 22.00 28.00 35.00 44.00 54.00 67.00 100 100 100 100 50 50 25 10 1777720000 1777730000 1777740000 1777750000 1777760000 1777770000 1777780000 1777790000 PG 7 PG 9 PG 11 PG 13.5 PG 16 PG 21 PG 29 PG 36 PG 42 PG 48 7.5 8 8 9 9 10 12 15 16 16 5 5 5 6 6 6 8 9 10 10 15.00 18.00 22.00 24.00 26.00 32.00 40.00 50.00 57.00 64.00 100 100 100 100 100 100 50 25 10 5 0521600000 0294700000 0294800000 0294900000 0295000000 0295100000 0501100000 0501200000 0501300000 1719270000 Other versions available on request. The sealing plugs must be tightened „hand-tight“ with the screwdriver. C.61 Sealing plugs Cable entries Sealing plugs - Plastic - Ex e C L L1 Sealing plug with cross-head is used to seal surplus threaded holes and to maintain the IP protection degree – especially for Ex-e Ex applications. Thread Technical data Material / Colour Temperature range Protection degree Protection degree with GWDR UL 94 flammability rating Approval Note Polyamide / RAL 9005 -20 °C...80 °C IP 66 IP 68 V-2 II 2 GD, Ex d llC, Ex e II, Ex tD Optional sealing ring Ordering data Typ metric VP M16-EXE SW VP M20-EXE SW VP M25-EXE SW VP M32-EXE SW VP M40-EXE SW VP M50-EXE SW VP M63-EXE SW Note C.62 Thread L L1 SW Qty. Order No. M 16 / 1.5 M 20 / 1.5 M 25 / 1.5 M 32 / 1.5 M 40 / 1.5 M 50 / 1.5 M 63 / 1.5 19 19 20 20.5 20.5 21 23.5 15 15 15 15 15 15 15 19 23 28 36 44 54 67 50 50 100 20 10 5 5 1737070000 1737080000 1737090000 1737100000 1737110000 1737120000 1737130000 Refer to the enclosed installation instructions for the tightening torque. 1420920000 – 2013 Sealing plugs Cable entries Sealing plugs - Brass - Ex e, Ex d L Sealing plug is used for sealing surplus threaded holes to ensure the IP protection degree especially for Ex-e and Ex-d applications. L1 C Thread Technical data Material O-Ring Temperature range Protection degree Approval Brass, nickel-plated NBR -40 °C...100 °C IP 68 II 2 GD, Ex d llC, Ex e II, Ex tD Note Ordering data Typ metric VP M16 EXE MS VP M20 EXE MS VP M25 EXE MS VP M32 EXE MS VP M40 EXE MS VP M50 EXE MS VP M63 EXE MS Note 1420920000 – 2013 Thread L L1 SW Qty. M 16 / 1.5 M 20 / 1.5 M 25 / 1.5 M 32 / 1.5 M 40 / 1.5 M 50 / 1.5 M 63 / 1.5 15 15 15.5 16 19 20 26 12 12 12 12 15 15 19 17 23 29 39 45 58 70 50 50 25 10 10 5 5 Order No. 1210890000 1210900000 1210910000 1210920000 1210930000 1210940000 1210950000 Refer to the enclosed installation instructions for the tightening torque. C.63 Sealing plugs Cable entries Sealing plugs - Brass - Ex e, Ex d, IP 54 L Thread Sealing plug with accessible hexagon recess. It is used to seal unused threaded holes so that cable glands can be connected in the future. Approved for use with the pressureresistant Ex d encapsulation. C L1 Technical data Material Temperature range Protection degree Approval Brass, nickel-plated -50 °C...180 °C IP 54 ATEX l M2 ll 2 GD Ex d l/llC Mb Gb Ex tb lllDb IP6X, IECEx Ex d l/llC & Ex e l/llC MbGb Ex tb llC Db IP6X Note Ordering data Typ metric KSPA M16 BNI KSPA M20 BNI KSPA M25 BNI KSPA M32 BNI KSPA M40 BNI KSPA M50 BNI KSPA M63 BNI KSPA M75 BNI Note C.64 Thread L1 Qty. M 16 M 20 M 25 M 32 M 40 M 50 M 63 M 75 16 16 16 16 16 16 16 16 20 20 20 10 10 1 1 1 Order No. 0887490000 0886670000 0886680000 0886690000 0886700000 0886710000 1075370000 1075380000 1420920000 – 2013 Sealing plugs Cable entries Sealing plugs - Brass and Stainless steel - Ex e, Ex d, IP 66 / IP 68 L Thread Dome head sealing plug with accessible hexagon recess. It is used to seal unused threaded holes so that cable glands can be connected in the future. Available in brass and stainless steel. Approved for use with the pressure-resistant Ex d encapsulation and increased safety Ex e. C L1 Technical data O-Ring Temperature range Protection degree Approval NBR -30 °C...100 °C IP 66, IP 68 ATEX l M2 ll 2 GD Ex dl/llC Mb Gb Ex e l/llC Mb Gb Ex tb lllC Db IP6X, IECEx Ex d l/llC & Ex e l/llC MbGb Ex tb llC Db IP6X Note Ordering data Typ Stainless steel KSPM M16 SSC KSPM M20 SSC KSPM M25 SSC KSPM M32 SSC KSPM M40 SSC KSPM M50 SSC KSPM M63 SSC KSPM M75 SSC brass KSPM M16 BSC KSPM M20 BSC KSPM M25 BSC KSPM M32 BSC KSPM M40 BSC KSPM M50 BSC KSPM M63 BSC KSPM M75 BSC Note 1420920000 – 2013 Thread L L1 Qty. Order No. M 16 M 20 M 25 M 32 M 40 M 50 M 63 M 75 21.5 21.5 21.5 21.5 21.5 21.5 21.5 21.5 16 16 16 16 16 16 16 16 20 20 20 10 10 1 1 1 0887500000 0886720000 0886730000 0886740000 0886750000 1075510000 1075520000 1075530000 M 16 M 20 M 25 M 32 M 40 M 50 M 63 M 75 21.5 21.5 21.5 21.5 21.5 21.5 21.5 21.5 16 16 16 16 16 16 16 16 20 20 20 10 10 1 1 1 0887480000 0885410000 0885420000 0885430000 0885440000 0885450000 1075480000 1075490000 C.65 Sealing plugs Cable entries Sealing plugs - Plastic - Ex e, IP 66 L Thread Sealing plugs with accessible hexagon recess, made from glass-fibre-reinforced nylon. They are used to seal unused threaded holes so that cable glands can be connected in the future – also recommended for Ex applications. C L1 Technical data Material O-Ring Temperature range Protection degree Approval Nylon NBR -20 °C...40 °C IP 66 II 2 GD, Ex e llC Gb, Ex tb lllC Db, IP6X Note Ordering data Typ metric KSPM M16 PL KSPM M20 PL KSPM M25 PL KSPM M32 PL KSPM M40 PL KSPM M50 PL Note C.66 Thread L L1 Qty. M 16 / 1.5 M 20 / 1.5 M 25 / 1.5 M 32 / 1.5 M 40 / 1.5 M 50 / 1.5 21.5 21.5 21.5 21.5 21.5 21.5 16 16 16 16 16 16 20 20 20 10 10 1 Order No. 1209890000 1209910000 1209920000 1209930000 1209940000 1209950000 1420920000 – 2013 Adaptors Cable entries Adaptors with NPT male threads Adaptors can be used to connect threaded holes and cable glands of different thread sizes and types. C Technical data Material Temperature range Protection degree Approval Brass, nickel-plated -40 °C...100 °C IP 54 II 2 GD, Ex d llC, Ex e II, Ex tD Ordering data External thread Inner thread M16 M20 M25 M32 M40 M50 M63 M75 1/2“ NPT 3/4“ NPT 1“ NPT 1 1/4“ NPT 1 1/2“ NPT 2“ NPT 2 1/2“ NPT 3“ NPT Note 1420920000 – 2013 1/2“ NPT Order No. 1737490000 1737650000 1737810000 1738410000 1738570000 3/4“ NPT Order No. 1“ NPT Order No. 1737640000 1737800000 1737950000 1737630000 1737790000 1738400000 1738560000 1738390000 1738550000 1738700000 1738820000 1 1/4“ NPT Order No. 1 1/2“ NPT Order No. 1738380000 1738540000 1738690000 1738810000 1738920000 1738370000 1738530000 1738680000 1738800000 1738910000 1738070000 2“ NPT Order No. 1737440000 1737600000 1737760000 1737910000 1738040000 1738150000 1738240000 1738310000 1738360000 1738520000 1738670000 1738790000 1738900000 1738990000 1739060000 2 1/2“ NPT Order No. 1737430000 1737590000 1737750000 1737900000 1738030000 1738140000 1738230000 1738300000 1738350000 1738510000 1738660000 1738780000 1738890000 1738980000 1739050000 1739100000 3“ NPT Order No. 1737420000 1737580000 1737740000 1737890000 1738020000 1738130000 1738220000 1738290000 1738340000 1738500000 1738650000 1738770000 1738880000 1738970000 1739040000 1739090000 Qty. = 1 C.67 Adaptors Cable entries Adaptors with metric male threads Adaptors can be used to connect threaded holes and cable glands of different thread sizes and types. C Technical data Material Temperature range Protection degree Approval Brass, nickel-plated -40 °C...100 °C IP 54 II 2 GD, Ex d llC, Ex e II, Ex tD Ordering data External thread Inner thread M16 M20 M25 M32 M40 M50 M75 1/2“ NPT 3/4“ NPT 1“ NPT 1 1/4“ NPT 1 1/2“ NPT 2“ NPT 2 1/2“ NPT 3“ NPT Note C.68 M 16 Order No. 1737730000 M 20 Order No. 1737560000 1737720000 1737880000 1738480000 1738640000 M 25 Order No. 1737550000 1737710000 1738010000 1738630000 1738760000 M 32 Order No. 1737540000 1737700000 1737860000 1738120000 1738460000 1738750000 1738870000 M 40 Order No. 1737530000 1737690000 1737850000 1737990000 1738110000 1738210000 1738450000 1738610000 1738740000 M 50 Order No. 1737520000 1737680000 1737840000 1737980000 1738100000 1738280000 1738440000 1738600000 1738730000 1738850000 M 63 Order No. 1737510000 1737670000 1737830000 1737970000 1738090000 1738190000 1738330000 1738430000 1738590000 1738720000 1738840000 1738940000 1739080000 M 75 Order No. 1737500000 1737660000 1737820000 1737960000 1738080000 1738180000 1738260000 1738420000 1738580000 1738710000 1738830000 1738930000 1739010000 1739070000 1739110000 Qty. = 1 1420920000 – 2013 Compensating elements Cable entries Compensation elements - Plastic - DAE L The DAE pressure-compensation element provides good ventilation for the enclosure and prevents moisture build-up. At the same time it maintains the high IP 69k protection level. The membrane repels water and oil. L1 C SW Technical data Material / Colour O-Ring Temperature range Protection degree Air flow Wasser inlet point UL 94 flammability rating Polyamide 6 / RAL 9005 NBR -40 °C...105 °C IP 66, IP 68, IP 69K 0.8 l/min at 0.1 bar ΔP, up to 7.6 l/min at 1bar ΔP > 1.5 bar V-2 Note Ordering data Typ metric DAE M12 PA long DAE M12 PA short Note 1420920000 – 2013 Thread L L1 SW Qty. M 12 / 1.5 M 12 / 1.5 17.4 13.4 10 6 17 17 10 10 Order No. 1868570000 1868560000 Light grey version - RAL 7035 - on request C.69 Compensating elements Cable entries Compensation elements - Stainless steel - DAE L The DAE pressure-compensation element provides good ventilation for the enclosure and prevents moisture build-up. At the same time it maintains the high IP 69k protection level. The membrane repels water and oil. L1 C SW Technical data Material O-Ring Temperature range Protection degree Air flow Wasser inlet point Stainless steel NBR -40 °C...105 °C IP 66, IP 68, IP 69K 0.8 l/min at 0.1 bar ΔP, up to 7.6 l/min at 1bar ΔP > 1.5 bar Note Ordering data Typ metric DAE M12 SS Note C.70 Thread L L1 SW Qty. M 12 / 1.5 21.1 10 17 10 Order No. 1868550000 1420920000 – 2013 Compensating elements Cable entries Compensation elements - BD 1 The BD1 compensation element can be used for enclosure ventilation and to prevent moisture build-up. It is specially designed for Ex applications. Thread Ø Thread 5 C L1 SW L 1.5 Technical data O-Ring Temperature range Protection degree Filter Approval NBR -30 °C...85 °C IP 66 HDPE insert Ex e II, II 2 GD Note Ordering data Typ metric, brass BD 1 brass metric, stainless steel 1.4404 316L BD 1 ss Note 1420920000 – 2013 Thread L L1 SW Qty. Order No. M 20 / 1.5 25 10 29 1 3080760000 M 20 / 1.5 25 10 29 1 3080770000 C.71 Compensating elements Cable entries Compensation elements - EWS L We recommend using the EWS drainage plug in order to drain moisture out of the enclosure. This component is not suitable for providing ventilation to the enclosure. SW L1 C Thread Technical data Material / Colour Temperature range Protection degree Flammability rating Approval Note Polyamide / RAL 9005 -20 °C...40 °C IP 54 V-2 Ex e II, II 2 GD Installed at the lowest point from the bottom in the wall of the enclosure Minimum enclosure wall thickness of 4 mm must be maintained. Ordering data Typ metric EWS M 25X1.5 Note C.72 Thread L L1 SW Qty. M 25 / 1.5 23 5 30 20 Order No. 1719740000 1420920000 – 2013 Compensating elements Breather drains – Klippon® BDX Cable entries ~ r T " The BDX compensating element is used for ventilating the enclosure and preventing a build up of moisture, particularly in Ex applications. Thread Ø* Thread 5 L1 SW L 1.5 C Technical data Material IP class Impact resistance Filter Flow rate Sealing ring Temperature range Plating Torque Note Stainless steel 1.4404 (316L) or brass CuZnPb (CZ121) IP 66 20 J sintered bronze 0.25 Litres per hour silicone O-ring -60 °C to +200 °C natural 10 Nm - T he breather-drain is only to be fitted on the bottom side of the enclosure, aligned vertically with the thread upwards, and at the lowest point to permit proper drainage. - Fully assembly instructions are supplied with the breather drain. The instructions must be read prior to installation and adhered to in full. - The water flow rate has been tested by a water filled empty enclosure (no pressure or heat producing internal components). The water flow rate can slightly differ by influences from operational parameter and environmental conditions. Ordering data Type KLIPPON BDX M20 B KLIPPON BDX M20 S KLIPPON BDX M20X15 S Note 1420920000 – 2013/2014 Material brass stainless steel stainless steel Thread M20 x 1.5 M20 x 1.5 M20 x 1.5 L/L1 22/10 22/10 27/15 Dimensions in mm SW 27 27 27 Diameter Ø* 26.2 26.2 26.2 Order No. 1292540000 1292530000 1344630000 C.73 Cable entries C C.74 1420920000 – 2013/2014