STANDARD SPACE PRODUCTS PROGRAM May 2016 For general information on Analog Devices Space Qualified products please visit the following address. http://www.analog.com/aerospace For technical inquiries on Aerospace Engineering Models please email us at [email protected] For Sales and Distribution contacts please visit the following address. http://www.analog.com/en/about-adi/corporate-information/sales-distribution.html Analog Devices, Inc. 7910 Triad Center Drive, Greensboro, NC 27409 1 Standard Space Products Program May 2016 ANALOG DEVICES STANDARD SPACE LEVEL PROGRAM Analog offers a lower cost, shorter lead-time alternative to SCD's if the part is not offered in SMD or JAN. Analog Devices will continue to process devices to a specific source control drawing. However, in most cases, the standard Analog Devices Space Level should satisfy most customers’ needs for full process control, traceability, reliability, lot qualifications and certified line. Analog Devices Standard Space Level processing is based on the current issue of MIL-PRF-38535 QML level "V" (see Attachment 1). The electrical parameters and end points for the Analog Devices Standard Space Level flow will be as described in the current Analog Devices Space Level data sheet for each part offered. Features of Analog Standard Space Level Program Include the Following: 1. MIL-PRF-38535 QML "V" certified facilities (Fab, Assembly and Test) unless otherwise noted on the product datasheet. 2. Wafer lot acceptance or SEM on most products except where not applicable. See datasheet. 3. Wafer lot traceability. 4. Hot solder dip lead finish as described in MIL-PRF-38535. 5. Marking with standard part number, lot seal date code and Analog Devices logo. 6. Technology Conformance Inspection, Attachments 2 and 2A. 7. Product Change Notification. Analog Devices, Inc. 7910 Triad Center Drive, Greensboro, NC 27409 2 May 2016 Standard Space Products Program COMMITMENT TO THE SPACE MARKET Analog Devices is committed to serving the needs of the world space community by manufacturing the highest quality data conversion and signal processing products. Analog Devices’ entry into the space level market occurred in August 1990 when it acquired Precision Monolithics Inc. located in Santa Clara, California. Analog Devices’ certified facilities have been supplying products for military and space applications since 1972. Analog Devices now offers state-of-the-art, data conversion and linear products to the space market place which were previously only available as commercial or military Class B products. Analog Devices space level operations located in Greensboro, North Carolina coordinates all space level V (class S) activities, including business development, manufacturing and engineering. The addition of new products is derived from our customers’ needs and the ability of these products to meet MIL-PRF-38535 QML level V requirements. Visit our web site (http://www.analog.com/aerospace) or call our factory contacts for the latest Class S updates as well as for radiation information on these and other products. Analog Devices, Inc. Aerospace Product Line standard product is available in one or more of the following processes: MIL-PRF-38535, QML LEVEL V MIL-PRF-38535, QML R (LEVEL V with Radiation Qualification) MIL-PRF-38535, JAN S MIL-PRF-38535, Analog Devices, Inc.'s Aerospace Product Line Standard Product See http://www.analog.com/aerospace. (Standard Space Level Products Program) The table beginning on page 3 lists the standard product offered by Analog Device's Aerospace Product Line. Product is also available in accordance with source control drawings. Please call factory for further information. For further information see contact list on cover page. ANALOG DEVICES SPACE LEVEL PRODUCTS Manufacturing Locations Space Level Compliance Wafer Fab Assembly Screening and Quality Conformance Inspection MIL-PRF-38535 Class V Compliant QMLV Devices Full Wafer Lot Acceptance: ADI Wilmington MA ADI Limerick, Ireland ADI Santa Clara Die Bank ADI Phils, Inc. Cavite, Philippines ADI Phils, Inc. Cavite, Philippines Standard Space Products (non-QMLV) SEM Inspection, most models: ADI Wilmington MA ADI Limerick, Ireland ADI Santa Clara Die Bank TSMC Taiwan ADI Phils, Inc. Cavite, Philippines ADI Phils, Inc. Cavite, Philippines ADI Phils, Inc. Cavite, Philippines ADI Phils, Inc. Cavite, Philippines Customer Specific Special Flows ADI Wilmington MA ADI Limerick, Ireland ADI Santa Clara Die Bank TSMC Taiwan Analog Devices, Inc. 7910 Triad Center Drive, Greensboro, NC 27409 3 May 2016 Standard Space Products Program ATTACHMENT 1 Analog Devices Standard Space Level Flow Test Status/ Alternate Flow 1. ESD No change 2. Wafer Lot Acceptance No change 3. Non-destruct bond pull Alternate Flow 4. Internal Visual Pkg/ Process Exceptions GIDEP Effective PCN Date Issue Date Number Comments MIL-STD-883 Test Method and Condition Initial qualification Noted on datasheet if not available. SEM available on all products. TM 5007 March 2003 02_0064 Equivalent to DSCC QMLV baseline process flow No change 100% to TM2010, condition A 5. Temperature Cycling 10 cycles 100% to TM1010, condition C 6. Constant Acceleration No change 100% to TM2001, condition E 7. Visual inspection No change 100% 8. PIND No change 100% to TM2020, condition A 9. Serialization No change 100% 10. X-ray No change 100% to TM2012 11. T1. Pre Burn-in Elec. No change 100% in accordance with device specification 12. Reverse Bias Burn-In No change 100% to TM1015, 72 hr at 150 deg C min, if required 13. T2. Interim Elec. No change 100% in accordance with device specification 14. Burn-in No change 100% to TM1015, 240 hr at 125 deg C min 15. T3. Post-Burn-In Elec. No change 16. PDA 100% in accordance with device specification No change 5%, 3% catastrophic 17. Final Electrical No change 100% in accordance with device specification 18. Group A No change MIL-PRF-38535 19. Seal, Fine Leak No change 100% to TM1014 20. Seal, Gross leak No change 100% to TM1014 21. External Visual No change 100% to TM2009 22. Radiation Latch-up No change When specified 23. Group B No change MIL-PRF-38535 24. Group C No change MIL-PRF-38535 25. Group D No change MIL-PRF-38535 26. Group E No change MIL-PRF-38535 TCI-- Analog Devices, Inc. 7910 Triad Center Drive, Greensboro, NC 27409 4 Standard Space Products Program May 2016 ATTACHMENT 2 Analog Devices Standard Space Level Offers 1. Group B per MIL-PRF-38535, Table II with attributes. 2. Group C per MIL-PRF-38535, Table IV with attributes and variables. 3. Group D per MIL-PRF-38535, Table V. 4. Group E, subgroup 2. Certificate of Conformance and test report. a. Standard Radiation Test Plan. Test in accordance with MIL-PRF-38535 with test points at 0K, 100Krad, and post 24 hours biased anneal. 5. Delta measurements over pre and post burn-in on selected parameters based on Analog Space Level Data Sheets. 6. Wafer lot acceptance or SEM on most products except where not applicable. See datasheet. 7. Test report ($2000) with each shipment includes: A. 100% processing attributes data. B. Electrical test variable data. C. Radiographic inspection report. D. Failure analysis report, if applicable. E. Group A attributes data. F. Certificate of Conformance. G. Technology Conformance Inspection data. Analog Devices, Inc. 7910 Triad Center Drive, Greensboro, NC 27409 5 May 2016 Standard Space Products Program ATTACHMENT 2A Technology Conformance Inspection Minimum Sampling Plan Group B, MIL-PRF-38535, Table II Subgroup Test Sample Size / Acc Remarks 1 Resistance to solvents 3(0) Not required for laser marking. 2 Bond Strength 22(0)* Die Shear 3(0) Solderability 22(0)** 3 * Applies to the number of wires in minimum of 4 devices. ** Applies to the number of leads on a minimum of 3 devices. Group C, MIL-PRF-38535, Table IV Subgroup 1 Test Sample Size / Acc Remarks Life Test 45(0) MIL-PRF-38535, app B, ¶ 4.2 c-1 Group D, MIL-PRF-38535, Table V Subgroup Test Sample Size / Acc Remarks 1 Physical Dimensions 15(0) Electrical rejects may be used 2 a. Lead Integrity b. Seal 15(0)* Electrical rejects may be used 3 a. b. c. d. e. f. Thermal shock Temperature cycling Moisture resistance Seal Visual End-point Electrical 15(0) Electrically good parts, Destroyed 4 a. b. c. d. e. f. Shock Vibration, variable freq. Acceleration Seal Visual Examination End-Point Electrical 15(0) Electrically good parts, Destroyed 5 a. Salt Atmosphere b. Seal c. Visual 15(0) Electrical rejects may be used 6 Internal water vapor 3(0) or 5(1) Electrical rejects may be used 7 Adhesion of lead finish 15(0)* Electrical rejects may be used 8 Lid Torque 5(0) Electrical rejects may be used 9 Soldering Heat 3(0)** * Applies to number of leads in minimum of 3 samples. ** Performed at qualification or design changes which may affect this test. Analog Devices, Inc. 7910 Triad Center Drive, Greensboro, NC 27409 6 May 2016 Standard Space Products Program ATTACHMENT 2A Technology Conformance Inspection Minimum Sampling Plan Group E-Subgroup 2, MIL-PRF-38535, Table B-I Subgroup 2 Test Sample Size / Acc Remarks Total Ionization Dose 22(0) / wafer lot or 4(0) / wafer 883 Method 1019, Cond. A Analog Devices, Inc. 7910 Triad Center Drive, Greensboro, NC 27409 7 Standard Space Products Program May 2016 ATTACHMENT 3 Analog Standard Space Level Product Ordering Information See Space Qualified Parts List Brochure (http://www.analog.com/aerospace) for list of product / package offering. |----------------------------------------------------------------Device Type | |-----------------------------------------------------Total Dose Radiation Designator (Optional) | | |-------------------------------------------Electrical Grade | | | |--------------------------------Radiation option for non "R" rated parts | | | | |---------------------Lead Finish | | | | | |----------Package Suffix OP 15 R 9 0 3 J | | | | | |----------Packages: | | | | | C = Die | | | | | D = Sidebrazed Ceramic Dip | | | | | E = Ceramic Leadless Chip Carrier | | | | | F = Ceramic Flat Pack (2, 16, & 28 Lead) | | | | | G = Ceramic Pin Grid Array | | | | | H = Hermetic Metal Can | | | | | J = 8-Lead TO-99 Can | | | | | L = 10-Lead Flat Pack | | | | | M = 14-Lead Flat Pack | | | | | N = 24-Lead Flat Pack | | | | | Q = 16-Lead Ceramic Dip (PMI Div) | | | | | Q = Ceramic Dip, Glass Seal (Analog Divisions) | | | | | R = 20-Lead Ceramic Dip | | | | | RC = 20-Lead Leadless Carrier | | | | | T = 28 Lead Ceramic Dip | | | | | TC = 28-Lead Leadless Carrier | | | | | X = 18-Lead Ceramic Dip | | | | | Y = 14-Lead Ceramic Dip | | | | | Z = 8-Lead Ceramic Dip | | | | |---------------------Lead Finish: | | | | 3 = Solder Dipped, preferred finish | | | ||-------------------------------Radiation option: | | | 0 = Standard product | | | 1 = Radiation Test - No Lot Jeopardy, call factory | | ||------------------------------------------Electrical Grade: | | -000 = Standard Die – call factory for datasheet | | -9XX = “A”, "M", or “U” Grade. | | -8XX = “B”, "L", “T”, or Plain Grade. | | -7XX = "K", or “S” Grade. | | | |-----------------------------------------------------Total Dose Radiation Designation (Optional) | MIL-PRF-38535 ¶ 3.4.3 RHA (no neutron test) | |----------------------------------------------------------------Per Analog Devices Space Level Data Sheets Examples: AD9058-803D = AD9058, “T” Grade, Sidebrazed package, Solder-Dipped Lead Finish. AD9058R803D = AD9058, “T” Grade, Sidebrazed package, Solder-Dipped Lead Finish, Qualified to 100Krad PM139-000C = PM139, Standard Die. PM139R000C = PM139, Standard Die, Qualified to 100Krad For QML Class “V” products see appropriate Standard Military Drawing 5962-XXXXXVXX. Analog Devices, Inc. 7910 Triad Center Drive, Greensboro, NC 27409 8 Standard Space Products Program May 2016 REVISION HISTORY Rev Description of Change 0 Initiate May 9, 2000 A Add revision history Attachment 1: remove reference to ADI0422, add 10 cycle note Attachment 2: remove # of samples from 1. add minimum to 4a, removed 80% of unit price. Attachment 2A: change "leads in" to "lead on" for Group B notes Jan. 16, 2001 B Update web page links. Dec. 19, 2001 C Change Radiation test from MIL-STD-883 M5004 to MIL-PRF-38535. May 31, 2002 D Add information for standard die on page 6: “Product Ordering Information” Feb. 7, 2003 E Modify factory contacts & company address Oct. 30, 2003 F Modify factory contacts & company address Jan. 9, 2006 G Modify Attachment 1 – Analog Devices Standard Space Level Flow Oct. 17, 2006 H Remove ref to ESD marking & Modify factory contacts Dec. 12, 2006 I Add program feature clarification to accommodate products with fab or test at a non QML “V” certified facility July 17, 2007 J Up-date Group C sample size per Mil-PRF-38535 Rev H. Sept. 13, 2007 K Update QCI items as part of standard test report Nov. 01,2011 L Update brand on header Dec. 14, 2015 M Update manufacturing location on page 3. May 06, 2016 Analog Devices, Inc. 7910 Triad Center Drive, Greensboro, NC 27409 Date 9