Video Encoder EI3 Extender Board Manual an EZ-Extender® product Revision 1.1, November 2012 Part Number 82-000252-01 Analog Devices, Inc. One Technology Way Norwood, Mass. 02062-9106 a Copyright Information © 2012 Analog Devices, Inc., ALL RIGHTS RESERVED. This document may not be reproduced in any form without prior, express written consent from Analog Devices, Inc. Printed in the USA. Disclaimer Analog Devices, Inc. reserves the right to change this product without prior notice. Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use; nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under the patent rights of Analog Devices, Inc. Trademark and Service Mark Notice The Analog Devices logo, Blackfin, CrossCore, EngineerZone, EZ-Board, EZ-Extender, EZ-KIT Lite, and VisualDSP++ are registered trademarks of Analog Devices, Inc. All other brand and product names are trademarks or service marks of their respective owners. Regulatory Compliance The Video Encoder EI3 Extender Board is designed to be used solely in a laboratory environment. The board is not intended for use as a consumer end product or as a portion of a consumer end product. The board is an open system design which does not include a shielded enclosure and therefore may cause interference to other electrical devices in close proximity. This board should not be used in or near any medical equipment or RF devices. The Video Encoder EI3 Extender Board has been certified to comply with the essential requirements of the European EMC directive 2004/108/EC and therefore carries the “CE” mark. The Video Encoder EI3 Extender Board has been appended to Analog Devices, Inc. EMC Technical File (EMC TF) referenced DSPTOOLS1, issue 2 dated June 4, 2008 and was declared CE compliant by an appointed Notified Body (No.0673) as listed below. Notified Body Statement of Compliance: Z600ANA2.045 dated September 3, 2012. Issued by: Technology International (Europe) Limited 56 Shrivenham Hundred Business Park Shrivenham, Swindon, SN6 8TY, UK The extender board contains ESD (electrostatic discharge) sensitive devices. Electrostatic charges readily accumulate on the human body and equipment and can discharge without detection. Permanent damage may occur on devices subjected to high-energy discharges. Proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Store unused extender boards in the protective shipping package. CONTENTS PREFACE Product Overview ......................................................................... ix Purpose of This Manual ................................................................. x Intended Audience ........................................................................ xi Manual Contents .......................................................................... xi What’s New in This Manual ......................................................... xii Technical Support ........................................................................ xii Supported Products ..................................................................... xiii Product Information ................................................................... xiii Analog Devices Web Site ....................................................... xiii EngineerZone ......................................................................... xiv Related Documents ....................................................................... xv Notation Conventions ................................................................... xv USING VIDEO ENCODER EI3 EXTENDER BOARD Package Contents .......................................................................... 1-2 Video Encoder EI3 Extender Board Installation ............................. 1-2 High Performance HDMI Transmitter (ADV7511) ........................ 1-3 Multi-Format Video Encoder (ADV7431) ..................................... 1-4 Video Encoder EI3 Extender Board Manual v Contents Expansion Interface III ................................................................. 1-5 Example Programs ........................................................................ 1-6 Board Design Database ................................................................. 1-7 VIDEO ENCODER EI3 EXTENDER BOARD HARDWARE REFERENCE System Architecture ...................................................................... 2-2 Software-Controlled Switches (SoftConfig) ................................... 2-3 Overview of SoftConfig ........................................................... 2-3 Programming SoftConfig ........................................................ 2-7 Video Encoder Mode Select ................................................... 2-10 ADV7511_INT_GPIOx Signal ............................................. 2-10 27MHZ_CLK_EN Signal ..................................................... 2-10 74MHZ_CLK_EN Signal ..................................................... 2-10 SPORT_ENABLE Signal ...................................................... 2-10 Connectors ................................................................................. 2-11 Expansion III (EI3) Connectors (J4) ...................................... 2-12 S-Video Connector (J2) ........................................................ 2-12 Component Connector (J14) ................................................ 2-13 HDMI Connector (J5) .......................................................... 2-13 Composite Connector (J6) .................................................... 2-14 Power Connector (P1) ........................................................... 2-14 LEDs ......................................................................................... 2-15 HDMI Detect LED (LED1) .................................................. 2-15 Power LED (LED2) .............................................................. 2-15 vi Video Encoder EI3 Extender Board Manual Contents VIDEO ENCODER EI3 EXTENDER BOARD BILL OF MATERIALS VIDEO ENCODER EI3 EXTENDER BOARD SCHEMATIC INDEX Video Encoder EI3 Extender Board Manual vii Contents viii Video Encoder EI3 Extender Board Manual PREFACE Thank you for purchasing the Video Encoder EI3 Extender Board, an EZ-Extender® product for EZ-KIT Lite®/EZ-Board® evaluation systems with the expansion interface 3 (EI3). The EZ-KIT Lite/EZ-Board and Video Encoder EI3 Extender Board are designed to be used in conjunction with the CrossCore® Embedded Studio (CCES) development environment. To learn more about Analog Devices development software, go to http://www.analog.com/processors/tools. Product Overview The Video Encoder EI3 Extender Board is a separately sold daughter board that plugs onto the expansion interface 3 (EI3) of an EZ-KIT Lite/EZ-Board evaluation system. The extender board aids the design and prototyping phases of embedded processor-targeted applications. The board extends the capabilities of the evaluation system by providing a connection between the parallel peripheral interface (PPI) of the processor and the ADV7511 and ADV7341 video encoders. The SPORT is used for transmitting audio data. The two-wire interface (TWI) port of the processor is used to communicate to the video encoders and SoftConfig on the extender. Video Encoder EI3 Extender Board Manual ix Purpose of This Manual The following is a list of the Video Encoder EI3 Extender Board interfaces. • Video interface • ADV7511 — 225 MHz, high performance HDMI transmitter with ARC • ADV7341— multi-format video encoder, six 12-bit noiseshaped video DACs • Video connectors • One HDMI • One SVIDEO • One component • One composite • No power supply required: derives power from the EZ-KIT Lite/EZ-Board • CE certified • Traditional mechanical switches and jumpers for changing the board’s factory setup have been removed in favor of I2C-controlled software switches. Purpose of This Manual The Video Encoder EI3 Extender Board Manual provides instructions for installing the product hardware (board). The text describes operation and configuration of the board components and provides guidelines for running your own code on the Video Encoder EI3 Extender Board. Finally, a schematic and a bill of materials are provided for reference. x Video Encoder EI3 Extender Board Manual Preface Intended Audience The primary audience for this manual is a programmer who is familiar with Analog Devices processors. This manual assumes that the audience has a working knowledge of the appropriate processor architecture, instruction set, and C/C++ programming languages. Programmers who are unfamiliar with Analog Devices processors can use this manual, but should supplement it with other texts that describe your target architecture and hardware development tools. Programmers who are unfamiliar with the CrossCore Embedded Studio programming environment or the mating evaluation board, should refer to the CCES online help. Manual Contents The manual consists of: • Chapter 1, “Using Video Encoder EI3 Extender Board” on page 1-1 Provides basic board information. • Chapter 2, “Video Encoder EI3 Extender Board Hardware Reference” on page 2-1 Provides information about the product’s hardware components. • Appendix A, “Video Encoder EI3 Extender Board Bill Of Materials” on page A-1 Provides a list of hardware components used to manufacture the extender board. • Appendix B, “Video Encoder EI3 Extender Board Schematic” on page B-1 Provides all circuits on the extender board. Video Encoder EI3 Extender Board Manual xi What’s New in This Manual What’s New in This Manual This is the second revision of the Video Encoder EI3 Extender Board Manual. It includes the updated regulatory compliance section and minor modifications based on the errata report against the first revision. Technical Support You can reach Analog Devices processors and DSP technical support in the following ways: • Post your questions in the processors and DSP support community at EngineerZone®: http://ez.analog.com/community/dsp • Submit your questions to technical support directly at: http://www.analog.com/support • E-mail your questions about processors, DSPs, and tools development software from CrossCore Embedded Studio or VisualDSP++®: Choose Help > Email Support. This creates an e-mail to [email protected] and automatically attaches your CrossCore Embedded Studio or VisualDSP++ version information and license.dat file. • E-mail your questions about processors and processor applications to: [email protected] or [email protected] (Greater China support) • In the USA only, call 1-800-ANALOGD (1-800-262-5643) xii Video Encoder EI3 Extender Board Manual Preface • Contact your Analog Devices sales office or authorized distributor. Locate one at: www.analog.com/adi-sales • Send questions by mail to: Processors and DSP Technical Support Analog Devices, Inc. Three Technology Way P.O. Box 9106 Norwood, MA 02062-9106 USA Supported Products This extender board supports EZ-KIT Lite/EZ-Board evaluation systems with the expansion interface 3. Product Information Product information can be obtained from the Analog Devices Web site and the CCES online help system. Analog Devices Web Site The Analog Devices Web site, www.analog.com, provides information about a broad range of products—analog integrated circuits, amplifiers, converters, and digital signal processors. To access a complete technical library for each processor family, go to http://www.analog.com/processors/technical_library. The manuals selection opens a list of current manuals related to the product as well as a link to the previous revisions of the manuals. When locating your manual Video Encoder EI3 Extender Board Manual xiii Product Information title, note a possible errata check mark next to the title that leads to the current correction report against the manual. Also note, myAnalog.com is a free feature of the Analog Devices Web site that allows customization of a Web page to display only the latest information about products you are interested in. You can choose to receive weekly e-mail notifications containing updates to the Web pages that meet your interests, including documentation errata against all manuals. myAnalog.com provides access to books, application notes, data sheets, code examples, and more. Visit myAnalog.com (found on the Analog Devices home page) to sign up. If you are a registered user, just log on. Your user name is your e-mail address. EngineerZone EngineerZone is a technical support forum from Analog Devices. It allows you direct access to ADI technical support engineers. You can search FAQs and technical information to get quick answers to your embedded processing and DSP design questions. Use EngineerZone to connect with other DSP developers who face similar design challenges. You can also use this open forum to share knowledge and collaborate with the ADI support team and your peers. Visit http://ez.analog.com to sign up. xiv Video Encoder EI3 Extender Board Manual Preface Related Documents For additional information about the product, refer to the following publications. Table 1. Related Processor Publications Title Description Processor Data Sheet General functional description, pinout, and timing of the processor Processor Hardware Reference Description of the internal processor architecture and all register functions Blackfin® Processor Programming Reference Description of all allowed processor assembly instructions Notation Conventions Text conventions used in this manual are identified and described as follows. Additional conventions, which apply only to specific chapters, may appear throughout this document. Example Description Close command (File menu) Titles in reference sections indicate the location of an item within the CCES environment’s menu system (for example, the Close command appears on the File menu). {this | that} Alternative required items in syntax descriptions appear within curly brackets and separated by vertical bars; read the example as this or that. One or the other is required. [this | that] Optional items in syntax descriptions appear within brackets and separated by vertical bars; read the example as an optional this or that. [this,…] Optional item lists in syntax descriptions appear within brackets delimited by commas and terminated with an ellipse; read the example as an optional comma-separated list of this. Video Encoder EI3 Extender Board Manual xv Notation Conventions Example Description .SECTION Commands, directives, keywords, and feature names are in text with letter gothic font. filename Non-keyword placeholders appear in text with italic style format. xvi Note: For correct operation, ... A Note provides supplementary information on a related topic. In the online version of this book, the word Note appears instead of this symbol. Caution: Incorrect device operation may result if ... Caution: Device damage may result if ... A Caution identifies conditions or inappropriate usage of the product that could lead to undesirable results or product damage. In the online version of this book, the word Caution appears instead of this symbol. Warning: Injury to device users may result if ... A Warning identifies conditions or inappropriate usage of the product that could lead to conditions that are potentially hazardous for the devices users. In the online version of this book, the word Warning appears instead of this symbol. Video Encoder EI3 Extender Board Manual 1 USING VIDEO ENCODER EI3 EXTENDER BOARD This chapter provides the setup procedure for the Video Encoder EI3 Extender Board and describes the interfaces the extender supports. The information is presented in the following order. • “Package Contents” on page 1-2 • “Video Encoder EI3 Extender Board Installation” on page 1-2 • “High Performance HDMI Transmitter (ADV7511)” on page 1-3 • “Multi-Format Video Encoder (ADV7431)” on page 1-4 • “Expansion Interface III” on page 1-5 • “Example Programs” on page 1-6 • “Board Design Database” on page 1-7 Video Encoder EI3 Extender Board Manual 1-1 Package Contents Package Contents Your Video Encoder EI3 Extender Board package contains the following items. • Video Encoder EI3 Extender Board • A bag containing hardware for securing the extender board on the EZ-KIT Lite/EZ-Board • Video cables – one HDMI and one component • Release note containing information about the product download Contact the vendor where you purchased your extender board or contact Analog Devices, Inc. if any item is missing. Video Encoder EI3 Extender Board Installation Follow these instructions to ensure correct operation of the product hardware and software. 1. Attach the extender board to the EZ-KIT Lite/EZ-Board. The J1 connector on the extender board can be connected to the P1A, P2A, or P3A connector on the EZ-KIT Lite/EZ-Board. Refer to the example program for a reference to the proper connector. 2. Use the provided hardware to secure the extender to the EZ-KIT Lite/EZ-Board. See Figure 1-1. 1-2 Video Encoder EI3 Extender Board Manual Using Video Encoder EI3 Extender Board 4 4 4 5 4 3 2 5 EZ-Extender 3 (Stacked) 2 1 2 Item Part Description 1 0.75in Nylon Standoff 2 1.0in Nylon Standoff 3 1.25in Nylon Standoff 4 Nylon Screw 5 Nylon Spacer 1 Figure 1-1. Assembled Board Diagram 3. Refer to the EZ-KIT Lite/EZ-Board manual for information on connecting to a personal computer (PC) and running CCES. High Performance HDMI Transmitter (ADV7511) The ADV7511 is a 225 MHz high-definition multimedia interface (HDMI) transmitter, which is ideal for home entertainment products including DVD players/receivers, digital set top boxes, A/V receivers, gaming consoles and PCs. The digital video interface contains an HDMI v1.4 and a DVI v1.0 compatible transmitter and supports all HDTV formats (including 1080p with 12-bit Deep Color). The ADV7511 supports the HDMI v1.4 spe- Video Encoder EI3 Extender Board Manual 1-3 Multi-Format Video Encoder (ADV7431) cific features, HEAC (ARC), and 3D video. In addition, the ADV7511 supports x.v.Color, high bit rate audio and programmable AVI Info Frames features. With the inclusion of HDCP, the ADV7511 allows the secure transmission of protected content as specified by the HDCP v1.4 protocol. The ADV7511 high-performance HDMI transmitter with ARC connects to the PPI, SPORT, TWI and GPIO of the processor. This device supports up to 1080p. The ADV7511 can be configured to generate an interrupt based on various events. The TWI port is used for communication between the transmitter and processor. The PPI is used for transmitting video data. The SPORT is used for transmitting audio data. An interrupt signal from the transmitter is connected to a GPIO signal on the processor. The GPIO signal is configured via a software switch. Refer to “Software-Controlled Switches (SoftConfig)” on page 2-3 for more information. For more information about the ADV7511, go to www.analog.com and search for ADV7511. An example program demonstrating capabilities of the ADV7511 is available by installing the Video Encoder EI3 Extender Board Support Package (BSP). Multi-Format Video Encoder (ADV7431) The ADV7341 is a high speed, digital-to-analog video encoder. Six high speed, NSV, 3.3V, 12-bit video DACs provide support for composite (CVBS), S-Video (Y-C), and component (YPrPb/RGB) analog outputs in standard definition (SD), enhanced definition (ED), or high definition (HD) video formats. The ADV7341 has a 30-bit pixel input port that can be configured in a variety of ways. SD video formats are supported over an SDR interface 1-4 Video Encoder EI3 Extender Board Manual Using Video Encoder EI3 Extender Board and ED/HD video formats are supported over SDR and DDR interfaces. Pixel data can be supplied in either the YCrCb or RGB color space. The part also supports embedded EAV/SAV timing codes, external video synchronization signals, and I2C communication protocol. In addition, simultaneous SD and ED/HD input and output are supported. Full-drive DACs ensure that external output buffering is not required, while 216 MHz (SD and ED) and 297 MHz (HD) oversampling ensures that external output filtering is not required. The ADV7341 multi-format video encoder connects to the PPI and TWI of the processor. This device supports up to 1080i/720p. The TWI port is used for communications between the encoder and processor. The PPI is used for transmitting video data. Refer to “Software-Controlled Switches (SoftConfig)” on page 2-3 for more information. For more information about the ADV7341, go to www.analog.com and search for ADV7341. An example program demonstrating capabilities of the ADV7341 is available by installing the Video Encoder EI3 Extender Board Support Package (BSP). Expansion Interface III The Expansion Interface III (EI3) allows an extender board to be tested across various hardware platforms that have the same expansion interface connectors. The EI3 implemented on the Video Encoder EI3 Expander Board contains the PPI, SPORT, TWI and GPIO ports. These signals are used for the peripherals on the extender. For pinout information, go to Appendix B, “Video Encoder EI3 Extender Board Schematic”. The Video Encoder EI3 Extender Board Manual 1-5 Example Programs mechanical dimensions of the expansion connectors can be obtained by contacting “Technical Support”. The Video Encoder EI3 Extender Board supports interfacing with EZ-Boards which are operating at an IO voltage of 3.3V. Other IO voltages are not supported. The Video Encoder EI3 Extender Board supports being powered from either the EZ-Board or through the on board 5V power connector (P1). For more information about other daughter boards, visit the Analog Devices Web site. Limits to current and interface speed must be taken into consideration when using the EI3. Current for the EI3 can be sourced from the EZ-KIT Lite/EZ-Board; therefore, the current should be limited to 200 mA for 5V and 300 mA for the 3.3V planes. If more current is required, then a separate power connector and a regulator must be designed on the daughter card. Additional circuitry can add extra loading to signals, decreasing their maximum effective speed. Devices does not support and is not responsible for the Analog effects of additional circuitry. Example Programs Example programs are included with the Video Encoder EI3 Extender Board Support Package (BSP). Example programs demonstrate various capabilities of the product. The support package is installed on top of CrossCore Embedded Studio. Once installed, the example programs can be found in the following directory: <install_path>\Video_Encoder_EI3_Extender_Board-RelX.X.X\Video_E ncoder_EI3, 1-6 where X.X.X denotes the support package release number. Video Encoder EI3 Extender Board Manual Using Video Encoder EI3 Extender Board Board Design Database A .zip file containing all of the electronic information required for the design, layout, fabrication, and assembly of the product is available for download from the Analog Devices board design database at: http://www.analog.com/en/processors-dsp/blackfin/processors/board-design-database/resources/index.html. Video Encoder EI3 Extender Board Manual 1-7 Board Design Database 1-8 Video Encoder EI3 Extender Board Manual 2 VIDEO ENCODER EI3 EXTENDER BOARD HARDWARE REFERENCE This chapter describes the hardware design of the Video Encoder EI3 Extender Board. The following topics are covered. • “System Architecture” on page 2-2 Describes the daughter board configuration and explains how the board components interface with the processor and EZ-KIT Lite. • “Software-Controlled Switches (SoftConfig)” on page 2-3 Lists and describes the software-controlled switches. • “Connectors” on page 2-11 Shows the locations and provides part numbers for the on-board connectors. In addition, the manufacturer and part number information is provided for the mating parts. • “LEDs” on page 2-15 Describes the on-board LEDs. Video Encoder EI3 Extender Board Manual 2-1 System Architecture System Architecture A block diagram of the Video Encoder EI3 Extender Board is shown in Figure 2-1. 3.3V EI3 Connector EPPI TWI GPIO 1.8V SPORT Voltage Regulation Bus Transceiver Power Soft Config MCP23017 Soft Config Soft Config Soft Config 74CB3Q16211 PI3C3125 PI3C3125 PPI TWI INT SPORT ADV7511 HDMI Transmitter HDMI Soft Config 74CB3Q16211 PPI TWI ADV7341 Video Encoder SVIDEO Component Composite Figure 2-1. Video Encoder EI3 Extender Board Block Diagram 2-2 Video Encoder EI3 Extender Board Manual Video Encoder EI3 Extender Board Hardware Reference Software-Controlled Switches (SoftConfig) On the Video Encoder EI3 Extender Board, all of the traditional mechanical switches/jumpers have been replaced by I2C software-controlled switches. Refer to any SoftConfig*.c file found in the installation directory of CCES for an example of how to set up the SoftConfig feature of the product through software. The SoftConfig section of this manual serves as a reference to any user that intends to modify an existing software example. If software provided by ADI is used, there should be little need to reference this section. should be taken when changing SoftConfig settings not to Care create a conflict with interfaces. The same GPIO signal and SPICS should not be configured for more than one interface. Overview of SoftConfig In order to further clarify the use of electronic single FET switches and multi-channel bus switches, an example of each is illustrated and compared to a traditional mechanical switching solution. This is a generic example. After this generic discussion there is a detailed explanation of the SoftConfig interface specific to the extender. Figure 2-2 shows two individual FET switches (Pericom PI3A125CEX) with reference designators UA and UB. Net names ENABLE_A and ENABLE_B control UA and UB. The default FET switch enable settings in this example are controlled by resistors RA and RB which pull the enable pin 1 of UA and UB to ground (low). In a real example, these enable signals are controlled by the Microchip IO expander. The default pull-down resistors connect the signals EXAMPLE_SIGNAL_A and EXAMPLE_SIGNAL_B and also connect signals EXAMPLE_SIGNAL_C and EXAMPLE_SIGNAL_D. To disconnect EXAMPLE_SIGNAL_A from EXAMPLE_SIGNAL_B, the Microchip IO expander is Video Encoder EI3 Extender Board Manual 2-3 Software-Controlled Switches (SoftConfig) used to change ENABLE_A to a logic 1 through software that interfaces with the Microchip. The same procedure for ENABLE_B would disconnect EXAMPLE_SIGNAL_C from EXAMPLE_SIGNAL_D. Figure 2-2. Example of Individual FET Switches Figure 2-3 shows the equivalent circuit to Figure 2-2 but utilizes mechanical switches that are in the same package. The default is shown by black boxes located closer to the ON label of the switches. In order to disconnect these switches, physically move the switch to the OFF position. Figure 2-3. Example of Mechanical Switch Equivalent to Figure 2-2 2-4 Video Encoder EI3 Extender Board Manual Video Encoder EI3 Extender Board Hardware Reference Figure 2-4 shows a bus switch example, reference designator UC (Pericom PI3LVD512ZHE), selecting between lettered functionality and numbered functionality. The signals on the left side are multiplexed signals with naming convention letter_number. Figure 2-4. Example of Bus Switch The right side of the circuit shows the signals separated into letter and number, with the number on the lower group (eg. 0B1) and the letter on the upper group (eg. 0B2). The default setting is controlled by the signal CONTROL_LETTER_NUMBER which is pulled low. This selects the number signals on the right to be connected to the multiplexed signals on the left by Video Encoder EI3 Extender Board Manual 2-5 Software-Controlled Switches (SoftConfig) default. In this example, the Microchip IO expander is not shown but controls the signal CONTROL_LETTER_NUMBER and allows the user to change the selection through software. Figure 2-5 shows the equivalent circuit to Figure 2-4 but utilizes mechanical switches. Notice the default for reference designators SWC and SWD is illustrated by black boxes located closer to the ON label of the switches to enable the number signals by default. Note the default setting for reference designators SWE and SWF is OFF. In order to connect the letters instead of the numbers, the user physically changes all switches on SWC and SWD to the OFF position and all switches on SWE and SEF to the ON position. Figure 2-5. Example of Mechanical Switch Equivalent to Figure 2-4 2-6 Video Encoder EI3 Extender Board Manual Video Encoder EI3 Extender Board Hardware Reference Programming SoftConfig On the Video Encoder EI3 Extender Board, a single Microchip MCP23017 device controls individual and electronic bus switches via TWI. The device has the following programming characteristics: • There are two programmable GPIO registers. GPIO Register Register Address GPIOA 0x12 GPIOB 0x13 • Each GPIO register controls eight signals (software switches). • By default, the GPIO signals function as input signals; therefore, all electronic switches are in the OFF state. The signals must be programmed as output signals to override their default values. The following table shows the Microchip register addresses and values that must be written to them to program the signals as output signals. IODIR Register IODIR Register Address Value to be Written to Program Signals as Outputs IODIRA 0x00 0 IODIRB 0x01 0 Video Encoder EI3 Extender Board Manual 2-7 Software-Controlled Switches (SoftConfig) Each example in Cross Core Embedded Studio includes source files that program the soft switches, even if the default settings are being used. The README for each example identifies only the signals that are being changed from their default values. The code that programs the soft switches is located in two files: • SoftConfig_Encoder.c • SoftConfig_xxx.c for configuring the extender board for configuring the EZ-KIT Lite/EZ-Board; xxx identifies the EZ-KIT Lite/EZ-Board file in each example. Page 2 of Appendix B, “Video Encoder EI3 Extender Board Schematic” shows how the GPIO signals are connected to the board’s ICs. and U10-U13 are 24-bit bus switches. They are used to select how the transmitter/encoder is connected to the processor. You can select an 8-bit, 16-bit, or 24-bit interface. U13 are 2-port bus switches. They are used for selecting which GPIO signals to use as the interrupt. U8-U9 is an 8-port bus switch. It is used to connect/disconnect the SPORT to the ADV7511. U18 Table 2-1 and Table 2-2 show the output signals of the GPIO expander (U10) with a TWI address of 0100 101X, where X represents the read or write bit. The signals that control an individual FET have an entry under the FET column. The Component Connected column shows the board IC that is connected if the FET is enabled. 2-8 Video Encoder EI3 Extender Board Manual Video Encoder EI3 Extender Board Hardware Reference Table 2-1. Output Signals of GPIO Expander (U19 Port A) Bit Signal Name Description FET Component Connected Default 0 24_BIT_ADV7511 24-bit video mode U10 U14 Off 1 24_BIT_ADV7341 24-bit video mode U11 U2 Off 2 16_BIT_ADV7511 16-bit video mode U13 U14 Off 3 16_BIT_ADV7341 16-bit video mode U12 U2 Off 4 27MHZ_CLK_EN Enable 27 MHz oscillator U15 Off 5 74MHZ_CLK_EN Enable 74 MHz oscillator U14 Off 6 8_BIT_ADV7341 8-bit video mode U3 U2 Off 7 SPORT_ENABLE Enable SPORT interface U18 U14 Off Table 2-2. Output Signals of GPIO Expander (U19 Port B) Bit Signal Name Description FET Component Connected Default 0 ADV7511_INT_GPIO0 Transmitter interrupt U9 U14 Off 1 ADV7511_INT_GPIO1 Transmitter interrupt U9 U14 Off 2 ADV7511_INT_GPIO2 Transmitter interrupt U19 U14 Off 3 ADV7511_INT_GPIO3 Transmitter interrupt U9 U14 Off 4 ADV7511_INT_GPIO4 Transmitter interrupt U8 U14 Off 5 ADV7511_INT_GPIO5 Transmitter interrupt U8 U14 Off 6 ADV7511_INT_GPIO6 Transmitter interrupt U8 U14 Off 7 ADV7511_INT_GPIO7 Transmitter interrupt U8 U14 Off Video Encoder EI3 Extender Board Manual 2-9 Software-Controlled Switches (SoftConfig) Video Encoder Mode Select The Video Encoder Mode Select determines whether the interface to the processors PPI is 8, 16 or 24 bits. The Video Encoder Mode select is chosen by driving low either the 24_BIT_ADV7511, 16_BIT_ADV7511, 24_BIT_ADV7341, 16_BIT_ADV7341 or 8_BIT_ADV7341 signal (U20 ports GPA0-GPA3, GPA6. Driving one of these signals low enables the appropriate bus switches (U10-U13 and U3). ADV7511_INT_GPIOx Signal The ADV7511_INT_GPIOx signal connects the interrupt signal of the ADV7511 to one of eight GPIO pins of the processor. U20 ports GPB0-GPB7 are used to select the connection to the appropriate GPIO signal via the U8 and U9 bus switch. 27MHZ_CLK_EN Signal The 27MHZ_CLK_EN signal is used to enable the onboard 27 MHz oscillator which connects to the ADV7511 and ADV7341. U20 port GPA4 is used to enable and disable the oscillator. The default is disabled. 74MHZ_CLK_EN Signal The 74MHZ_CLK_EN signal is used to enable the onboard 74.25 MHz oscillator which connects to the ADV7511 and ADV7341. U20 port GPA5 is used to enable and disable the oscillator. The default is disabled. SPORT_ENABLE Signal The SPORT_ENABLE signal connects the audio signal of the ADV7511 to the SPORT interface of the processor. U20 port GPA7 is used to enable or disable the connection via the U18 bus switch. The default is disabled. 2-10 Video Encoder EI3 Extender Board Manual Video Encoder EI3 Extender Board Hardware Reference Connectors This section describes connector functionality and provides information about mating connectors. Figure 2-6 shows the locations of all connectors on the Video Encoder EI3 Extender Board. Figure 2-6. Connector Locations denoted by a dotted line are located on the opposite Connectors side of the board. Video Encoder EI3 Extender Board Manual 2-11 Connectors Expansion III (EI3) Connectors (J4) One board-to-board connectors (J4) provide signals from the PPI, SPORT, TWI, and GPIO interfaces of the processor. The connector is located on the bottom side of the board. Part Description Manufacturer Part Number 120-pin, 0.6 mm HIROSE FX8-120S-SV(21) Mating Connector 120-pin, 0.6 mm HIROSE FX8-120P-SV1(91) S-Video Connector (J2) The S-Video connector (J2) is a DIN connector which connects to the ADV7341. This connector can be used for Y-C mode and supports SD, ED, and HD video modes. Part Description Manufacturer Part Number S-Video CUI MD-40SM Mating Cable S-Video Cable 2-12 Belkin F8V308-06 Video Encoder EI3 Extender Board Manual Video Encoder EI3 Extender Board Hardware Reference Component Connector (J14) The Component connector (J14) is a group of three RCA jacks which connect to the ADV7341. This connector can be used for YPrPb and RGB modes and supports SD, ED, and HD video modes. Part Description Manufacturer Part Number Component (3x1 RCA) CUI RCJ-32265 Mating Cable Component Cable Belkin AV21000-06 HDMI Connector (J5) The HDMI connector (J5) is an HDMI receptacle that is connected to the ADV7511. This connector can be used for YCbCr and RGB modes and supports SD, ED, and HD video modes. It supports ARC and is v.1.4 compliant. Part Description Manufacturer Part Number HDMI FCI 10029449-002TLF Mating Cable HDMI Cable Mediabridge Video Encoder EI3 Extender Board Manual 91-02X-06B 2-13 Connectors Composite Connector (J6) The Composite connector (J6) is a single RCA jack which connects to the ADV7341. This connector can be used for CVBS and supports SD, ED, and HD video modes. Part Description Manufacturer Part Number Composite (1 RCA) Switchcraft PJRAN1X1U01X Mating Cable Composite Cable Kobiconn 17FH101 Power Connector (P1) Under normal circumstances the power connector is not needed because the Video Encoder EI3 Extender Board derives its power from the EZ-KIT Lite/EZ-Board. If the EZ-KIT Lite/Video Encoder EI3 Extender Board is not able to supply enough power to the Video Encoder EI3 Extender Board, then an external power supply can be connected to P14 which will power the Video Encoder EI3 Extender Board and EZ-KIT Lite/EZ-Board. Part Description Manufacturer Part Number 0.65 mm power jack CUI 045-0883R Mating Cable [email protected] power supply 2-14 GLOBETEK GS-1750(R) Video Encoder EI3 Extender Board Manual Video Encoder EI3 Extender Board Hardware Reference LEDs This section describes the on-board LEDs. HDMI Detect LED (LED1) When LED1 is lit solid (yellow), it indicates that an HDMI device has been detected (connected to the HDMI connector (J5)). Power LED (LED2) When LED2 is lit solid (green), it indicates that power is being supplied to the board properly. Video Encoder EI3 Extender Board Manual 2-15 LEDs 2-16 Video Encoder EI3 Extender Board Manual A VIDEO ENCODER EI3 EXTENDER BOARD BILL OF MATERIALS The bill of materials corresponds to “Video Encoder EI3 Extender Board Schematic” on page B-1. Ref. Qty. Description Reference Designator Manufacturer Part Number 1 1 SN74LVC1G125 SOT23-5 U22 TI 74LVC1G125DBVRE4 2 2 SN74LVC1G04 SOT23-5 U4-U5 TI SN74LVC1G04DBVT 3 1 27MHZ OSC003 U15 EPSON SG-8002CA-MP 4 5 SN74CB3Q16211 TSSOP56 U3,U10-U13 DIGI-KEY 296-17629-1-ND 5 1 SN74AVC4T245 SOIC16 U1 DIGI-KEY 296-17930-1-ND 6 1 SN74AVC8T245 TSSOP24 U18 TI SN74AVC8T245PW 7 1 12MHZ OSC015 U17 DIGI-KEY 535-9413-2-ND 8 1 MCP23017 QFN65P600X600-29N U19 DIGI-KEY MCP23017-E/ML-ND 9 3 PI3C3125 TSSOP14 U7-U9 PERICOM PI3C3125 10 1 74.25MHZ OSC003 U16 CTS CB3LV-3I-74M2500 11 1 74AVC24T245 LFBGA84 U6 DIGI-KEY 296-17662-1-ND 12 1 ADV7341BSTZ LQFP64 U2 ADI ADV7341BSTZ 13 3 ADA4430 SC70_6 U23-U25 ADI ADA4430-1YKSZ-R2 14 1 ADP1706-1.8V LFCSP8 VR2 ADI ADP1706ACPZ-1.8-R7 15 1 ADP1706-3.3V LFCSP8 VR1 ADI ADP1706ACPZ-3.3-R7 16 1 10MA AD1580BRTZ SOT23D D7 ADI AD1580BRTZ-R2 Video Encoder EI3 Extender Board Manual A-1 Ref. Qty. Description Reference Designator Manufacturer Part Number 17 1 ADV7511KSTZ LQFP100 U14 ADI ADV7511KSTZ 18 1 RCA 1X1 CON012 J6 SWITCHCRAFT PJRAN1X1U01X 19 1 PWR .65MM CON027 P1 DIGI-KEY CP1-022PJCT-ND 20 1 1A RESETABLE 1206 F1 RAYCHEM NANOSMDC110F-2 21 1 HDMI 19P FCI_10029449-002TLF J5 FCI 10029449-002LF 22 1 RCA 3X1 CUI-STACK_RCJ-32265 J1 DIGI-KEY CP-1446-ND 23 1 MINI-DIN 4PIN CUI-STACK_MD-40SM J2 DIGI-KEY CP-2240-ND 24 1 .6MM 120PIN HIROSE_FX8-120S-SV(21) J4 HIROSE FX8-120S-SV(21) 25 1 YELLOW LED001 LED1 DIGI-KEY P512TR-ND 26 3 10K 1/10W 5% 0805 R5,R7,R9 VISHAY CRCW080510K0JNEA 27 3 10K 1/10W 5% 0805 R6,R8,R10 VISHAY CRCW080510K0JNEA 28 2 10K 31MW 5% RNET8 RN1-RN2 CTS 746X101103JP 29 9 10UH 10% 1008 L1-L9 PANASONIC ELJ-FC100KF 30 9 10UF 6.3V 10% 0805 C22,C49,C58, C66,C68, C84-C85,C92, C95 AVX 08056D106KAT2A A-2 Video Encoder EI3 Extender Board Manual Video Encoder EI3 Extender Board Bill Of Materials Ref. Qty. Description Reference Designator Manufacturer Part Number 31 45 0.1UF 10V 10% 0402 C1-C4,C7-C12, C14-C19,C23, C26,C29-C30, C35-C37,C40, C43-C44,C51, C53-C54,C57, C60-C62,C64, C70,C72-C73, C76-C77,C80, C82,C87,C90, C93,C96 AVX 0402ZD104KAT2A 32 19 0.01UF 16V 10% 0402 C41-C42,C45, C48,C50,C52, C55-C56,C59, C65,C69,C71, C74-C75,C81, C83,C86,C91, C94 AVX 0402YC103KAT2A 33 12 10K 1/16W 5% 0402 R3-R4, R14-R16,R18, R25,R28-R29, R40,R43,R46 VISHAY CRCW040210K0FKED 34 2 4.7K 1/16W 5% 0402 R30,R38 VISHAY CRCW04024K70JNED 35 2 0 1/16W 5% 0402 R57-R58 PANASONIC ERJ-2GE0R00X 36 7 0 1/16W 5% 0402 R11,R13, R26-R27,R49-R 51 PANASONIC ERJ-2GE0R00X 37 5 33 1/16W 5% 0402 R1-R2,R12, R17,R56 VISHAY CRCW040233R0JNEA 38 2 2.2UF 10V 10% 0805 C38-C39 AVX 0805ZD225KAT2A 39 4 4.7UF 6.3V 20% 0603 C46-C47,C63, C67 AVX 06036D475MAT2A 40 6 75.0 1/10W 1% 0603 R41-R42, R47-R48, R52-R53 DALE CRCW060375R0FKEA Video Encoder EI3 Extender Board Manual A-3 Ref. Qty. Description Reference Designator Manufacturer Part Number 41 2 1UF 6.3V 20% 0402 C20-C21 PANASONIC ECJ-0EB0J105M 42 1 GREEN LED001 LED2 PANASONIC LN1361CTR 43 1 1.1K 1/16W 1% 0402 R37 PANASONIC ERJ-2RKF1101X 44 2 430 1/16W 1% 0402 R19,R54 DIGI-KEY 311-430LRCT-ND 45 1 VARISTOR V5.5MLA 30A 0603 R55 LITTLEFUSE V5.5MLA0603 46 2 0.15UF 10V 10% 0603 C31,C33 AVX 0603ZC154KAT2A 47 3 1A MBR130LSFT1G SOD-123FL D4-D6 ON SEMI MBR130LSFT1G 48 1 27K 1/16W 5% 0402 R20 PANASONIC ERJ-2GEJ273X 49 8 4700PF XXX 2A FIL_NFE61PT FER1-FER8 DIGI-KEY 490-2554-2-ND 50 1 887 1/10W 1% 0603 R32 DIGI-KEY 311-887HRTR-ND 51 3 5A RCLAMP0524 DIO_RCLAMP0524 D9-D11 SEMTECH RCLAMP0524P.TCT 52 1 30MA DB3X314 DIO_DB3X314 D8 PANASONIC DB3X314K0L 53 2 49.9 1/16W 1% 0402 R23-R24 STACKPOLE RMCF0402FT49R9 54 3 2.0K 1/10W 1% 0402 R21-R22,R31 PANASONIC ERJ-2RKF2001X 55 1 4.12K 1/10W 1% 0402 R33 PANASONIC ERJ-2RKF4121X 56 2 0.012UF 10V 10% 0402 C32,C34 DIGI-KEY 399-3009-2-ND 57 2 169.0 1/10W 1% 0402 R35-R36 PANASONIC ERJ-2RKF1690X 58 1 510.0 1/10W 1% 0402 R34 PANASONIC ERJ-2RKF5100X 59 3 300.0 1/10W 1% 0402 R39,R44-R45 PANASONIC ERJ-2RKF3000X 61 3 100MA BAT54S SOT23D D1-D3 FAIRCHILD BAT54S A-4 Video Encoder EI3 Extender Board Manual A B D C 1 1 Video Encoder EI3 Extender Board Schematic 2 2 3 3 ANALOG DEVICES 4 Title Size A B C Nashua, NH 03063 4 PH: 1-800-ANALOGD Video Encoder EI3 Extender Board Title Sheet Board No. Rev A0252-2010 C Date 20 Cotton Road 1.0 Sheet 3/6/12 D 1 of 8 A B D C J4 94 EI3_PPICLK 95 EI3_PPIFS2 101 EI3_PPID0 102 EI3_PPID2 103 EI3_PPID4 105 EI3_PPID6 106 EI3_PPID8 107 EI3_PPID10 108 EI3_PPID12 1 12 EI3_PPID14 111 EI3_PPID16 112 EI3_PPID18 113 EI3_PPID20 114 EI3_PPID22 99 87 EI3_SPORT0_CLK 89 EI3_SPORT0_FS 29 88 EI3_SPORT0_D0 32 EI3_SPORT0_D1 35 82 83 33 39 37 61 2 56 79 EI3_SCL 80 EI3_SDA PPI0_CLK 27 PPI0_FS1 EI3_PPIFS1 PPI0_FS2 26 PPI0_FS3 EI3_PPIFS3 PPI0_D0 20 PPI0_D1 EI3_PPID1 PPI0_D2 19 PPI0_D3 EI3_PPID3 PPI0_D4 18 PPI0_D5 EI3_PPID5 PPI0_D6 16 PPI0_D7 EI3_PPID7 PPI0_D8 15 PPI0_D9 EI3_PPID9 PPI0_D10 14 PPI0_D11 EI3_PPID11 PPI0_D12 13 PPI0_D13 EI3_PPID13 U19 PPI0_D14 110 PPI0_D15 EI3_PPID15 10 PPI0_D17 5 VDD PPI0_D16 EI3_PPID17 PPI0_D18 9 PPI0_D19 EI3_PPID19 EI3_SCL PPI0_D20 8 PPI0_D21 EI3_PPID21 EI3_SDA PPI0_D22 7 PPI0_D23 EI3_PPID23 TWI Address 0100 101x x is the R/W bit. Read - 1, Write - 0 SoftConfig control signals 3.3V 8 SCL R11 0402 0 9 SDA 14 RESET EI3_RESET PPI0_INT SPORT0_CLK SPORT0_FS SPORT0_TDV 3.3V 92 SPORT1_CLK 90 SPORT1_FS EI3_SPORT1_CLK EI3_SPORT1_FS 91 SPORT1_D0 SPORT0_D1 31 SPORT1_D1 SPI0_MISO SPI0_D2 EI3_SPORT1_CLK R58 0 0402 DNP EI3_SPORT1_D0 EI3_SPORT1_D1 SPORT_INT SPI0_CLK 15 INTB EI3_SPORT0_CLK 30 SPORT1_TDV SPORT0_D0 16 INTA R57 0 0402 DNP EI3_SPORT0_FS R10 10K 0805 EI3_SPORT1_FS R9 10K 0805 DNP R8 10K 0805 1 17 GPA0 24_BIT_ADV7511 18 GPA1 24_BIT_ADV7341 19 GPA2 16_BIT_ADV7511 20 GPA3 16_BIT_ADV7341 21 GPA4 27MHZ_CLK_EN 22 GPA5 74MHZ_CLK_EN 23 GPA6 8_BIT_ADV7341 24 GPA7 SPORT_ENABLE 25 GPB0 ADV7511_INT_GPIO0 26 GPB1 ADV7511_INT_GPIO1 27 GPB2 ADV7511_INT_GPIO2 28 GPB3 ADV7511_INT_GPIO3 1 GPB4 ADV7511_INT_GPIO4 50 SPI0_RDY 11 A0 2 GPB5 ADV7511_INT_GPIO5 84 SPI0_MOSI 12 A1 3 GPB6 ADV7511_INT_GPIO6 13 4 GPB7 ADV7511_INT_GPIO7 34 SPI0_D3 SPI0_SEL1/SPI0_SS* 85 SPI0_SEL_A SPI0_SEL_B SPI0_SEL_C A2 MCP23017 QFN65P600X600-29N 38 R7 10K 0805 DNP EXT_BOOT R6 10K 0805 R5 10K 0805 DNP 2 TWI0_A0* SCL0* 42 SCL1* SDA0* 41 SDA1* GPIO0 78 GPIO1 EI3_GPIO1 GPIO2 77 GPIO3 EI3_GPIO3 GPIO4 76 GPIO5 EI3_GPIO5 GPIO6 74 GPIO7* EI3_GPIO7 3.3V 43 EI3_GPIO0 44 EI3_GPIO2 45 EI3_GPIO4 47 EI3_GPIO6 48 49 3.3V 3.3V C96 0.1UF 0402 73 TMR_A TMR_B TMR_C 72 TMR_D* R25 10K 0402 R4 10K 0402 U15 59 UART0_RX 62 UART0_TX U4 1 OE 65 60 PWR_IN VIN WAKE* RESET_IN* 64 SLEEP* 3 R3 10K 0402 EI3_RESET USB_VCC 71 OUT 3.3V GND 27MHZ 2 OSC003 SN74LVC1G04 SOT23-5 57 RESET_OUT* R1 33 0402 4 VDD TP7 U7 CLKOUT R56 33 0402 1 OE0 27MHZ_CLK_EN 2 3 1 120 VIN PS_IN 116 VIO 6 17 28 40 52 63 75 86 98 109 117 2 22 25 53 55 4 67 70 97 119 GND1 4 GND2 GND3 11 GND4 GND5 23 GND6 GND7 36 GND8 GND9 46 GND10 GND11 58 GND12 GND13 69 GND14 GND15 GND16 GND17 93 GND18 GND19 104 GND20 GND21 115 GND22 GND23 118 GND24 RSVD1 21 RSVD2 RSVD3 24 RSVD4 RSVD5 51 RSVD6 RSVD7 54 RSVD8 RSVD9 66 RSVD10 RSVD11 68 RSVD12 RSVD13 96 RSVD14 RSVD15 100 RSVD16 PPICLK 3 4 74MHZ_CLK_EN OE1 5 A1 3.3V 3 3 B0 A0 5 USB_VCC 6 B1 10 OE2 9 A2 8 B2 13 OE3 U16 U5 1 R2 33 0402 4 VDD OE OUT 12 A3 11 B3 PI3C3125 TSSOP14 3 TP16 GND 74.25MHZ 2 OSC003 SN74LVC1G04 SOT23-5 81 3.3V 3.3V C30 0.1UF 0402 C29 0.1UF 0402 3.3V C2 0.1UF 0402 C3 0.1UF 0402 C4 0.1UF 0402 ANALOG DEVICES Title RSVD17 HIROSE_FX8-120S-SV(21) Size A B C Nashua, NH 03063 4 PH: 1-800-ANALOGD Video Encoder EI3 Extender Board EI3 Connector/GPIO Extender Board No. Rev A0252-2010 C Date 20 Cotton Road 1.0 Sheet 3/6/12 D 2 of 8 A B D C 3.3V 3.3V 3.3V U6 3.3V B4 VCCA1 VCCB1 D4 VCCA2 VCCB2 H4 VCCA3 VCCB3 L4 VCCA4 VCCB4 N4 VCCA5 1 EI3_PPID0 B6 1A1 EI3_PPID1 B5 1A2 1B2 EI3_PPID2 C6 1A3 1B3 EI3_PPID3 C5 1A4 1B4 EI3_PPID4 D6 2A1 2B1 EI3_PPID5 D5 2A2 2B2 EI3_PPID6 E6 2A3 2B3 EI3_PPID7 E5 2A4 2B4 F6 EI3_PPID8 1B1 3A1 3B1 EI3_PPID9 F5 3A2 3B2 EI3_PPID10 G6 3A3 3B3 EI3_PPID11 G5 3A4 3B4 H6 EI3_PPID12 4A1 4B1 EI3_PPID13 H5 4A2 4B2 EI3_PPID14 J6 4A3 4B3 EI3_PPID15 J5 4A4 EI3_PPID16 K6 5A1 5B1 EI3_PPID17 K5 5A2 5B2 4B4 L6 EI3_PPID18 5A3 5B3 L5 EI3_PPID19 5A4 5B4 M6 EI3_PPID20 2 VCCB5 6A1 6B1 M5 EI3_PPID21 6A2 6B2 N6 EI3_PPID22 6A3 6B3 N5 EI3_PPID23 3.3V R14 10K 0402 6A4 6B4 A6 1OE GND1 P6 1DIR GND2 A5 2OE GND3 P5 2DIR GND4 A4 3OE GND5 P4 3DIR GND6 A3 4OE GND7 P3 4DIR GND8 A2 5OE GND9 P2 5DIR GND10 A1 6OE GND11 P1 6DIR GND12 GND13 3.3V B3 C10 0.1UF 0402 D3 C36 0.1UF 0402 C37 0.1UF 0402 C61 0.1UF 0402 H3 L3 C12 0.1UF 0402 N3 B1 C11 0.1UF 0402 PPID0 B2 PPID1 C1 1 3.3V PPID2 C2 3.3V 3.3V PPID3 D1 3.3V PPID4 D2 C9 0.1UF 0402 PPID5 E1 PPID6 E2 C62 0.1UF 0402 C76 0.1UF 0402 C77 0.1UF 0402 U18 PPID7 F1 R16 10K 0402 PPID8 F2 1 VCC_A 23 VCC_B1 24 VCC_B2 PPID9 G1 PPID10 G2 H1 H2 J1 J2 K2 L1 L2 B1 PPID11 EI3_SPORT0_D1 PPID12 EI3_SPORT1_D0 5 A3 PPID13 EI3_SPORT1_D1 6 A4 B4 PPID14 EI3_SPORT0_CLK 7 A5 B5 EI3_SPORT0_FS 8 A6 20 B2 B3 19 18 17 16 B6 PPID16 9 A7 B7 PPID17 10 A8 B8 SPORT0_D0 SPORT0_D1 SPORT1_D0 SPORT1_D1 SPORT0_CLK SPORT0_FS 15 14 PPID18 2 DIR GND1 PPID19 22 OE GND2 SPORT_ENABLE M1 21 A1 4 A2 PPID15 K1 3 EI3_SPORT0_D0 11 12 PPID20 13 GND3 M2 PPID21 N1 2 SN74AVC8T245 TSSOP24 PPID22 N2 PPID23 C3 C4 E3 E4 F3 F4 G4 3.3V 3.3V J3 J4 K3 K4 RN2 M3 C15 0.1UF 0402 M4 C26 0.1UF 0402 24_BIT_ADV7341 R3 4 R4 6 27MHZ_CLK_EN R5 7 74MHZ_CLK_EN 3 R6 3.3V ADV7511_INT_GPIO0 EI3_GPIO0 9 R15 10K 0402 ADV7511_INT_GPIO1 U1 1 VCCA 4 PPICLK 13 1A1 1B1 5 EI3_PPIFS1 12 1A2 1B2 6 EI3_PPIFS2 11 2A1 2B1 7 EI3_PPIFS3 16 VCCB EI3_GPIO1 R12 0402 33 EI3_PPICLK ADV7511_INT_GPIO2 PPIFS1 EI3_GPIO2 PPIFS2 ADV7511_INT_GPIO3 10 2A2 2B2 2 EI3_GPIO3 15 1OE 1DIR 3 RN1 3 B0 ADV7511_INT 5 A1 ADV7511_INT_GPIO1 6 B1 9 A2 12 A3 ADV7511_INT_GPIO4 EI3_GPIO4 3.3V ADV7511_INT_GPIO5 3.3V EI3_GPIO5 ADV7511_INT_GPIO6 EI3_GPIO6 C8 0.1UF 0402 ADV7511_INT_GPIO7 C7 0.1UF 0402 EI3_GPIO7 R5 7 R6 8 ADV7511_INT_GPIO6 R7 9 ADV7511_INT_GPIO7 R8 U8 1 OE0 2 A0 10K RNET8 B0 3 4 OE1 5 A1 6 B1 10 OE2 9 A2 ANALOG DEVICES 8 B2 13 OE3 12 A3 11 B3 Title Size Date C 20 Cotton Road Nashua, NH 03063 4 PH: 1-800-ANALOGD Video Encoder EI3 Extender Board Voltage Translators Board No. Rev A0252-2010 C B R4 6 B3 PI3C3125 TSSOP14 A R3 ADV7511_INT_GPIO5 11 10 COM2 4 ADV7511_INT_GPIO4 13 OE3 2 R2 ADV7511_INT_GPIO3 8 B2 5 COM1 3 ADV7511_INT_GPIO2 10 OE2 1 R1 ADV7511_INT_GPIO0 4 OE1 14 SN74AVC4T245 SOIC16 4 10K RNET8 PI3C3125 TSSOP14 2OE 2DIR R8 U9 1 OE0 2 A0 3.3V R7 SPORT_ENABLE TP4 3 8 8_BIT_ADV7341 3.3V 10 COM2 3 16_BIT_ADV7341 TP17 2 R2 16_BIT_ADV7511 TP5 5 COM1 R1 24_BIT_ADV7511 74AVC24T245 LFBGA84 1 1.0 Sheet 3/6/12 D 3 of 8 A B D C 3.3V 3.3V TP8 2 PPID0 3 PPID1 PPID2 4 1A3 52 1B3 ADV7511_D6 PPID3 5 1A4 51 1B4 ADV7511_D7 PPID4 6 1A5 50 1B5 ADV7511_D8 4 PPID2 5 PPID3 6 PPID4 PPID5 7 1A6 48 1B6 ADV7511_D9 PPID6 9 1A7 47 1B7 ADV7511_D10 7 PPID5 9 PPID6 PPID7 10 1A8 46 1B8 ADV7511_D11 PPID8 11 1A9 45 1B9 ADV7511_D16 PPID9 12 1A10 44 1B10 ADV7511_D17 10 PPID7 11 PPID8 PPID10 13 1A11 43 1B11 ADV7511_D18 PPID11 14 1A12 42 1B12 ADV7511_D19 12 PPID9 3.3V 13 PPID10 14 PPID11 56 1OE 56 PPID12 15 2A1 41 2B1 ADV7511_D20 PPID13 16 2A2 40 2B2 ADV7511_D21 PPID14 18 2A3 39 2B3 ADV7511_D22 PPID15 20 2A4 37 2B4 ADV7511_D23 C14 0.1UF 0402 15 PPID12 16 PPID13 18 PPID14 20 PPID15 PPID16 21 2A5 36 2B5 PPID17 22 2A6 35 2B6 PPID18 23 2A7 34 2B7 PPID19 24 2A8 33 2B8 ADV7511_D31 PPID20 25 2A9 32 2B9 ADV7511_D32 PPID21 26 2A10 31 2B10 ADV7511_D33 PPID22 27 2A11 30 2B11 ADV7511_D34 PPID23 28 2A12 29 2B12 ADV7511_D28 21 PPID16 ADV7511_D29 22 PPID17 ADV7511_D30 23 PPID18 24 PPID19 25 PPID20 26 PPID21 27 PPID22 ADV7511_D35 28 PPID23 53 1B2 ADV7341_C3 1A3 52 1B3 ADV7341_C4 1A4 51 1B4 ADV7341_C5 1A5 50 1B5 ADV7341_C6 1A6 48 1B6 ADV7341_C7 1A7 47 1B7 ADV7341_C8 1A8 46 1B8 ADV7341_C9 1A9 45 1B9 ADV7341_Y2 1A10 44 1B10 ADV7341_Y3 1A11 43 1B11 ADV7341_Y4 1A12 42 1B12 ADV7341_Y5 1 3.3V 1OE 3.3V 2A1 41 2B1 ADV7341_Y6 2A2 40 2B2 ADV7341_Y7 2A3 39 2B3 ADV7341_Y8 2A4 37 2B4 ADV7341_Y9 2A5 36 2B5 ADV7341_S2 C16 0.1UF 0402 TP6 U3 ADV7341_S3 2A7 34 2B7 ADV7341_S4 2A8 33 2B8 ADV7341_S5 2A10 31 2B10 ADV7341_S7 ADV7341_S8 2A12 29 2B12 ADV7341_S9 ADV7341_S5 6 50 1B5 ADV7341_S6 7 48 1B6 ADV7341_S7 9 47 1B7 ADV7341_S8 10 46 1B8 ADV7341_S9 11 45 1B9 12 44 1B10 13 43 1B11 14 42 1B12 1A6 PPID6 30 2B11 51 1B4 1A5 PPID5 2A11 ADV7341_S4 5 1A4 PPID4 ADV7341_S6 52 1B3 1A3 PPID3 32 2B9 ADV7341_S3 4 1A2 PPID2 2A9 ADV7341_S2 53 1B2 1A1 PPID1 35 2B6 54 1B1 3 2 PPID0 2A6 1A7 PPID7 1A8 SN74CB3Q16211 TSSOP56 24-Bit Mode RGB 4:4:4 1A10 GND3 49 GND4 2OE GND2 GND2 38 GND3 49 GND4 55 24_BIT_ADV7341 19 1A11 1A12 24-Bit Mode RGB 4:4:4 1OE 15 41 2B1 16 40 2B2 18 39 2B3 20 37 2B4 21 36 2B5 22 35 2B6 23 34 2B7 24 33 2B8 2A1 3.3V 2A2 2A3 2A4 3.3V 2A5 TP11 2A6 5 1A4 51 1B4 PPID4 6 1A5 50 1B5 ADV7511_D24 PPID5 7 1A6 48 1B6 ADV7511_D25 PPID6 9 1A7 47 1B7 ADV7511_D26 10 1A8 PPID7 46 1B8 ADV7511_D23 PPID3 PPID4 PPID5 PPID6 ADV7511_D27 PPID7 PPID8 11 1A9 45 1B9 ADV7511_D28 PPID9 12 1A10 44 1B10 ADV7511_D29 PPID8 PPID10 13 1A11 43 1B11 ADV7511_D30 PPID11 14 1A12 42 1B12 ADV7511_D31 PPID9 3.3V PPID10 PPID11 56 1OE 5 6 7 9 10 11 12 13 14 56 PPID12 15 2A1 41 2B1 ADV7511_D32 PPID13 16 2A2 40 2B2 ADV7511_D33 C18 0.1UF 0402 PPID12 PPID13 15 16 37 2B4 ADV7511_D35 21 2A5 36 2B5 22 2A6 35 2B6 23 2A7 34 2B7 23 24 2A8 33 2B8 24 25 2A9 32 2B9 26 2A10 31 2B10 26 27 2A11 30 2B11 27 28 2A12 29 2B12 16-Bit Mode YCbCr 4:2:2 A PPID14 PPID15 18 20 21 22 25 28 16_BIT_ADV7341 55 17 VCC 27 52 1B3 30 2B11 1A3 ADV7341_C4 28 51 1B4 29 2B12 1A4 ADV7341_C5 1A5 50 1B5 ADV7341_C6 1A6 48 1B6 ADV7341_C7 1A7 47 1B7 ADV7341_C8 1A8 46 1B8 ADV7341_C9 1A9 45 1B9 ADV7341_Y2 1A10 44 1B10 ADV7341_Y3 1A11 43 1B11 ADV7341_Y4 1A12 42 1B12 ADV7341_Y5 2A1 41 2B1 ADV7341_Y6 2A2 40 2B2 ADV7341_Y7 2A3 39 2B3 ADV7341_Y8 2A4 37 2B4 ADV7341_Y9 2A5 36 2B5 2A6 35 2B6 2A7 34 2B7 2A8 33 2B8 2A9 32 2B9 2A10 31 2B10 2A11 30 2B11 2A12 29 2B12 2A10 2A11 2A12 55 2OE SN74CB3Q16211 TSSOP56 2OE SN74CB3Q16211 TSSOP56 C17 0.1UF 0402 ANALOG DEVICES Title 16-Bit Mode YCbCr 4:2:2 B 3 8-Bit Mode YCbCr 4:2:2 3.3V 1OE 49 38 SN74CB3Q16211 TSSOP56 19 16_BIT_ADV7511 4 8 55 2OE GND4 ADV7511_D34 PPID15 GND3 39 2B3 20 2A4 GND2 18 2A3 GND1 PPID14 31 2B10 ADV7341_C3 C1 0.1UF 0402 GND2 38 GND3 49 GND4 PPID3 4 53 1B2 GND1 PPID2 26 1A2 8 ADV7511_D22 3 32 2B9 2A9 GND4 PPID1 25 49 ADV7511_D21 2A8 ADV7341_C2 GND3 PPID2 52 1B3 2A7 54 1B1 1A1 GND2 53 1B2 4 1A3 2 38 3 1A2 PPID0 R29 10K 0402 19 PPID1 ADV7511_D20 GND1 54 1B1 8 3 VCC 2 1A1 PPID0 17 TP10 U12 3.3V 56 8_BIT_ADV7341 3.3V U13 2 19 SN74CB3Q16211 TSSOP56 ADV7341_C2 1A2 1A9 GND1 55 2OE 24_BIT_ADV7511 8 2 54 1B1 1A1 17 ADV7511_D5 VCC 53 1B2 38 3 1A2 ADV7511_D4 19 PPID1 U11 54 1B1 17 VCC 2 1A1 GND1 1 PPID0 8 U10 17 VCC TP9 Size C Nashua, NH 03063 4 PH: 1-800-ANALOGD Video Encoder EI3 Extender Board Video Modes Board No. Rev A0252-2010 C Date 20 Cotton Road 1.0 Sheet 3/6/12 D 4 of 8 A ADV7511_AVDD B ADV7511_AVDD C19 0.1UF 0402 ADV7511_PVDD ADV7511_PLVDD ADV7511_BGVDD R18 10K 0402 L1 10UH 1008 ADV7511_PVDD U17 R17 33 0402 4 VDD 1 OE 1 D C OUT 3 ADV7511_PLVDD CEC_CLK ADV7511_AVDD C22 10UF 0805 GND 12MHZ 2 OSC015 1 ADV7511_33 ADV7511_DVDD U14 79 PPICLK R20 27K 0402 CLK PPIFS1 98 HSYNC PPIFS2 2 VSYNC 97 47 TP12 TP13 TP14 TP25 DVDD_33V TP19 1 DVDD119 DVDD249 DVDD376 DVDD477 DVDD5 21 PVDD124 PVDD225 PVDD3 26 BGVDD 29 AVDD134 AVDD241 AVDD3 ADV7511_33 D8 DB3X314 DE DIO_DB3X314 TXC- TWI Address 0111 001x x is the R/W bit. Read - 1, Write - 0 TXC+ 95 D1 TX0- 94 D2 TX0+ TX1- ADV7511_D5 91 D5 TX2- ADV7511_D6 90 D6 43 TX2+ ADV7511_D7 89 D7 88 87 D8 CEC D9 CEC_CLK 85 DDCSCL D11 DDCSDA 83 D13 82 D14 HEAC- 81 D15 HEAC+ ADV7511_D16 80 D16 ADV7511_D17 78 D17 42 TXC+ CEC TX0- CEC_CLK TX0+ TX1TX1+ 5V ADV7511_DVDD TX2TX2+ 48 R21 2.0K 0402 50 R22 2.0K 0402 R23 49.9 0402 2 R24 49.9 0402 C20 1UF 0402 73 ADV7511_D19 HPD ADV7511_D21 71 D21 ADV7511_D22 70 D22 ADV7511_D23 69 D23 ADV7511_D24 68 D24 ADV7511_D25 67 D25 ADV7511_D26 66 D26 DSD0 ADV7511_D27 65 D27 DSD1 63 ADV7511_D29 D28 DSD2 D29 DSD3 ADV7511_D30 62 D30 DSD4/DST_ST ADV7511_D31 61 D31 DSD5/DST_FL ADV7511_D32 60 D32 DSD_CLK/DST_CLK ADV7511_D33 59 D33 ADV7511_D34 58 D34 SPDIF ADV7511_D35 57 D35 I2S0 I2S1 45 ADV7511_INT INT I2S2 38 PD I2S3 MCLK EI3_SCL 0 55 SCL SCLK 56 SDA LRCLK LQFP100 ADV7511KSTZ DDCSDA 51 HEAC-/HPD 52 30 R28 10K 0402 HEAC-/HPD 3 4 5 U22 6 3.3V 3 HEAC-/HPD 7 SN74LVC1G125 SOT23-5 8 LED1 YELLOW LED001 9 C23 0.1UF 0402 10 12 13 14 15 SPORT0_D0 R19 430 0402 SPORT0_D1 SPORT1_D0 SPORT1_D1 11 16 17 SPORT0_CLK SPORT0_FS 46 ANALOG DEVICES Close to U14 as possible and opposite pcb side 4 Title Size Date C 20 Cotton Road Nashua, NH 03063 4 PH: 1-800-ANALOGD Video Encoder EI3 Extender Board ADV7511 Board No. Rev A0252-2010 C B HDMI Device Detected R_EXT R32 887 0603 A R27 0 0402 28 18 20GND1 22GND2 23GND3 27GND4 31GND5 37GND6 44GND7 75GND8 99GND9 100GND10 GND11 SPDIF_OUT R31 2.0K 0402 HEAC+ C21 1UF 0402 D19 ADV7511_D20 64 DDCSCL 54 D18 72 D20 ADV7511_D28 53 1 74 ADV7511_D18 EI3_SDA 40 TXC- 86 D10 84 D12 R13 0402 39 TX1+ ADV7511_D11 R30 4.7K 0402 36 92 D4 ADV7511_D10 ADV7511_33 35 ADV7511_D4 ADV7511_D9 3 33 93 D3 ADV7511_D8 2 96 D0 32 1.0 Sheet 3/6/12 D 5 of 8 A B D C ADV7341_PVDD ADV7341_33 1 1 C38 2.2UF 0805 C39 2.2UF 0805 3.3V ADV7341_DVDD 3 4 ADV7341_Y2 5 35 COMP2 45 COMP1 41 VAA 34 PVDD 1 56 VDD2 VDD_IO 2 VDD1 U2 10 TWI Address 0101 011x x is the R/W bit. Read - 1, Write - 0 Y0 Y1 DAC1 Y2 DAC2 Y3 44 DAC1 DAC1 Y4 43 DAC2 DAC2 Y5 42 DAC3 DAC3 Y6 39 DAC4 DAC4 Y7 38 DAC5 DAC5 ADV7341_Y8 12 Y8 37 DAC6 ADV7341_Y9 13 Y9 ADV7341_Y3 6 ADV7341_Y4 7 ADV7341_Y5 8 ADV7341_Y6 9 ADV7341_Y7 51 ADV7341_S2 ADV7341_S3 ADV7341_S4 ADV7341_S5 ADV7341_S6 ADV7341_S7 53 54 55 58 59 60 C32 0.012UF 0402 DAC6 R35 169.0 0402 S0 52 S1 2 EXT_LF1 R48 75.0 0603 ADV7341_PVDD R52 75.0 0603 R53 75.0 0603 C31 0.15UF 0603 33 2 S2 C34 0.012UF 0402 S3 S4 DAC3 Place as close to U2 as possible and on same pcb side Place close to U2 31 EXT_LF2 R36 169.0 0402 S5 S6 C33 0.15UF 0603 S7 ADV7341_S8 61 S8 ADV7341_S9 62 S9 R37 1.1K 0402 ADV7341_33 46 VREF 14 15 ADV7341_C2 ADV7341_C3 ADV7341_C4 ADV7341_C5 ADV7341_C6 ADV7341_C7 3 16 17 18 25 26 27 C0 C1 47 RSET1 C2 36 RSET2 SOT23D C4 R33 4.12K 0402 C5 C6 ADV7341_C9 29 C9 ADV7341_33 R38 4.7K 0402 3 30 CLKIN_A 63 CLKIN_B PPIFS1 PPIFS2 R34 510.0 0402 C7 28 C8 PPICLK D7 AD1580BRTZ C3 ADV7341_C8 TP15 C35 0.1UF 0402 22 19 ALSB P_HSYNC 21 SCL 23 P_VSYNC 20 SDA EI3_SCL R26 0402 0 EI3_SDA 24 P_BLANK 49 S_VSYNC LQFP64 ADV7341BSTZ 11 DGND1 57 DGND2 64 GND_IO 32 PGND 40 AGND 50 S_HSYNC 48 SFL ANALOG DEVICES 4 Title Size A B C Nashua, NH 03063 4 PH: 1-800-ANALOGD Video Encoder EI3 Extender Board ADV7341 Board No. Rev A0252-2010 C Date 20 Cotton Road 1.0 Sheet 3/6/12 D 6 of 8 A B D C 3.3V ADV7341_33 1 1 2 1 2 R43 10K 0402 ADV7341_33 2 DAC5 D1 BAT54S 3 D2 BAT54S SOT23D 3 D3 BAT54S SOT23D 3 C43 0.1UF 0402 J1 SOT23D 1 2 C42 0.01UF 0402 R44 300.0 0402 U24 1 VIN VS+ 2 GND PD 3 SAG VOUT 6 R42 75.0 0603 5 4 ADA4430 SC70_6 1 75 Ohm traces R 1 4 Component G 3 6 J2 ADV7341_33 CUI-STACK_MD-40SM MINI-DIN R46 10K 0402 ADV7341_33 CUI-STACK_RCJ-32265 RCA R49-R51 should be very close to J3. R50 0 0402 4 C Place close to ADV7341 B 5 R49 0 0402 DAC6 C44 0.1UF 0402 R51 0 0402 C45 0.01UF 0402 R45 300.0 0402 U25 1 VIN VS+ 2 GND PD 3 SAG VOUT 6 R47 75.0 0603 5 4 ADA4430 SC70_6 J3 Terminators close to video filters 4 1 DAC3 2 DAC1 3 DAC2 13 PPIFS1 2 14 PPIFS2 9 15 12 1 GND12 GND25 GND36 GND47 GND5 3 Y GND1 RED 5 GND2 GREEN 6 GND3 BLUE 7 GND4 HS 8 GND5 VS 10 GND6 VGA_5V 11 GND7 VGA_SCL 16 GND8 VGA_SDA 17 GND9 Place close to ADV7341 VGA S-Video 2 EDAC_634-015-263-032 DSUB DNP ADV7341_33 5V 75 Ohm traces 100 Ohm diff pairs (50 Ohms to GND) J5 1 TX2+ 2 TMDS_DATA2+ TMDS_SHIELD2 DAC4 3 TX2- TMDS_DATA2- 4 TX1+ TMDS_DATA1+ 5 TMDS_DATA0+ 8 TMDS_SHIELD0 9 TX0- TMDS_DATA0- 10 TXC+ TMDS_CLOCK+ 11 3 3 SAG VOUT R41 75.0 0603 5 2 4 ADA4430 SC70_6 3 Composite SDA 17 DDC/CEC_GND 18 DDCSDA PD Terminator close to video filter SCL 16 DDCSCL HDMI HEC 15 CEC 2 GND J6 RCA CON012 6 Place close to ADV7341 CEC 14 HEAC-/HPD VS+ 1 TMDS_CLOCK- 13 HEAC+ R39 300.0 0402 U23 1 VIN TMDS_CLK_SHIELD 12 TXC- C41 0.01UF 0402 TMDS_DATA1- 7 TX0+ C40 0.1UF 0402 TMDS_SHIELD1 6 TX1- R40 10K 0402 ADV7341_33 +5V 19 HOT_PLUG_DETECT FCI_10029449-002TLF HDMI HEAC-/HPD TXC- TX1- DDCSDA TXC+ TX1+ DDCSCL TX0- TX2- HEAC+ TX0+ TX2+ D9 10 OUT1 1 IN2 9 OUT2 2 IN3 7 OUT3 4 6 OUT4 5 8 GND2 3 2 4 5 IN4 4 3 GND1 D11 D10 IN1 1 RCLAMP0524 DIO_RCLAMP0524 IN1 10 OUT1 1 IN2 9 OUT2 2 IN3 7 OUT3 4 IN4 6 OUT4 5 GND1 8 GND2 3 RCLAMP0524 DIO_RCLAMP0524 10 IN1 OUT1 9 IN2 OUT2 ANALOG DEVICES 7 IN3 OUT3 6 IN4 OUT4 GND1 8 GND2 RCLAMP0524 DIO_RCLAMP0524 R55 VARISTOR 0603 Title Size A Date B C Nashua, NH 03063 4 PH: 1-800-ANALOGD Video Encoder EI3 Extender Board Video Connectors Board No. Rev A0252-2010 C CEC 20 Cotton Road 1.0 Sheet 3/6/12 D 7 of 8 A B D C L2 10UH 1008 FER1 1 IN 3.3V ADV7511_DVDD 3 OUT 2 GND C49 10UF 0805 NFE61PT472 FIL_NFE61PT TP24 TP23 TP20 TP21 C50 0.01UF 0402 C51 0.1UF 0402 C52 0.01UF 0402 C53 0.1UF 0402 C55 0.01UF 0402 C54 0.1UF 0402 C56 0.01UF 0402 C57 0.1UF 0402 TP22 LED2 GREEN LED001 1 L3 10UH 1008 FER2 R54 430 0402 1 IN 1 ADV7511_PVDD 3 OUT 2 GND C58 10UF 0805 NFE61PT472 FIL_NFE61PT L4 10UH 1008 FER3 1 IN C59 0.01UF 0402 C60 0.1UF 0402 C65 0.01UF 0402 C64 0.1UF 0402 ADV7511_BGVDD 3 OUT 2 GND C66 10UF 0805 NFE61PT472 FIL_NFE61PT L5 10UH 1008 FER4 2 1 IN ADV7511_AVDD 2 3 OUT 2 GND C68 10UF 0805 NFE61PT472 FIL_NFE61PT C69 0.01UF 0402 C70 0.1UF 0402 C71 0.01UF 0402 C72 0.1UF 0402 C83 0.01UF 0402 C82 0.1UF 0402 C81 0.01UF 0402 C80 0.1UF 0402 C74 0.01UF 0402 C73 0.1UF 0402 1.8V @ 1A L6 10UH 1008 FER5 1 TP3 5V TP1 IN 1.8V ADV7341_DVDD 3 OUT 2 GND 1 EN 3 5 OUT1 IN1 6 OUT2 IN2 7 SENSE SS 2 GND 4 8 C84 10UF 0805 NFE61PT472 FIL_NFE61PT VR2 C46 4.7UF 0603 ADP1706-1.8V LFCSP8 L7 10UH 1008 FER6 3 C47 4.7UF 0603 VIN USB_VCC C48 0.01UF 0402 1 IN 3 3 OUT 2 GND PWR_IN C85 10UF 0805 NFE61PT472 FIL_NFE61PT D4 MBR130LSFT1G SOD-123FL ADV7341_PVDD C86 0.01UF 0402 C87 0.1UF 0402 C91 0.01UF 0402 C90 0.1UF 0402 F1 1A 1206 TP2 D5 MBR130LSFT1G SOD-123FL 3.3V VR1 1 5 OUT1 3 6 OUT2 4 7 SENSE EN IN1 D6 MBR130LSFT1G SOD-123FL IN2 8 SS L8 10UH 1008 FER7 2 GND 1 IN ADV7511_33 3 OUT 2 GND C67 4.7UF 0603 C92 10UF 0805 NFE61PT472 FIL_NFE61PT ADP1706-3.3V LFCSP8 P1 3 C63 4.7UF 0603 2 C75 0.01UF 0402 1 5V_POWER CON027 L9 10UH 1008 FER8 1 IN 4 ANALOG DEVICES ADV7341_33 3 OUT 2 GND NFE61PT472 FIL_NFE61PT C95 10UF 0805 3.3V @ 1A C94 0.01UF 0402 C93 0.1UF 0402 Title Size A B C Nashua, NH 03063 4 PH: 1-800-ANALOGD Video Encoder EI3 Extender Board Power Board No. Rev A0252-2010 C Date 20 Cotton Road 1.0 Sheet 3/6/12 D 8 of 8 I INDEX Numerics 27MHZ_CLK_EN signal, 2-10 74MHZ_CLK_EN signal, 2-10 A ADV7341 video encoder, ix ADV7511_INT_GPIOx signal, 2-10 ADV7511 video encoder, ix architecture, of Video Encoder EI3 Extender Board, 2-2 B bill of materials, A-1 block diagram of Video Encoder EI3 Extender Board, 2-2 board design database, 1-7 board schematic (Video Encoder EI3 Extender Board), B-1 bus switch, 2-5 example, 2-5 composite (J6), 2-14 expansion III (EI3) (J4), 2-12 HDMI (J5), 2-13 power (P1), 2-14 single RCA jack, 2-14 S-video DIN (J2), 2-12 triple RCA jack (J4), 2-13 contents, of this extender board package, 1-2 D design reference info, 1-7 E EngineerZone, xiv expansion III (EI3) connectors (J4), 2-12 extender board block diagram, 2-2 F FET switches, 2-3 example, 2-4 C H component connector (J14), 2-13 composite connector (J6), 2-14 configuration, of Video Encoder EI3 Extender Board, 1-2 connector locations, 2-11 connectors 120-pin 0.6 mm pitch, 2-12 component (J14), 2-13 HDMI connector (J5), 2-13 HDMI Detect LED (LED1), 2-15 I installation, of Video Encoder EI3 Extender Board, 1-2 interfaces, x Video Encoder EI3 Extender Board Manual I-1 Index L 27MHZ_CLK_EN, 2-10 74MHZ_CLK_EN, 2-10 ADV7511_INT_GPIOx, 2-10 SPORT_ENABLE, 2-10 video encoder mode select, 2-10 SoftConfig, 2-3 overview, 2-3 programming switches, 2-7 software-controlled switches (SoftConfig), 2-3 SPORT_ENABLE signal, 2-10 supported products, xiii S-video connector (J2), 2-12 switches programming SoftConfig, 2-7 system architecture, 2-2 LEDs, 2-15 HDMI Detect (LED1), 2-15 power (LED2), 2-15 M mechanical switch, 2-4, 2-6 N notation conventions, xv P package contents, 1-2 power connector (P1), 2-14 power LED (LED2), 2-15 product information, xiii product overview, ix T technical support, xii R V related documents, xv related processor publications, xv video connectors, x Video Encoder EI3 Extender Board interfaces, x video encoder mode select, 2-10 video interface, ADV7341, x ADV7511, x S schematic, of Video Encoder EI3 Extender Board, B-1 signals I-2 Video Encoder EI3 Extender Board Manual