8 7 6 5 4 3 2 1 THIS DOCUMENT CONTAINS CONFIDENTIAL, PROPRIETARY INFORMATION OF ITW CAMTEX REVISIONS IT MAY NOT BE REPRODUCED, DUPLICATED, OR DISCLOSED EXCEPT AS AUTHORIZED BY ITW CAMTEX ZONE - REV. ECN DESCRIPTION CHANGE BY 6/26/03 KSY 01/19/04 MA MA / ZAMZ 03/03/04, 06/24/04 09/19/05 ZAMZ 02/07/06 MA PreA NEW ISSUED PreB REDESIGNED A 1082/1145 NEW RELEASED / EDITORIAL 1274 1366 322.6 DATE EDITORIAL EDITORIAL 315.0 X WW LL 1 132.08 0.20 M +0.25 - 0.13 132.59 A Y M 0.20 M +0.25 - 0.13 A YM LEFT END WW 3.0X45 CHAM. F Y B (7X) 37.01 SECTION WW-WW 0.76 A PPE ITW CAMTEX COUNTRY OF ORIGIN 7.62 TO RECYCLE CALL 7 2.54 6.35 1.27 DETAIL F SCALE 2 : 1 +0.25 - 0.13 0.20 M MADE IN USA COUNTRY OF ORIGIN 311.15 A XM DETAIL A SCALE 4 : 1 ITW Camtex A MADE IN MALAYSIA MADE IN MALTA 871 -15 27.94 MQFP C RIGHT END 28x28x3.4 30.94 (2x)12.7 (2X) 37.01 1 135.9 1 (2x)92.1 1 150°C MAX LL SECTION LL-LL B 311.66 0.20 M +0.25 - 0.13 A X M LABEL DETAILS SCALE : 2X NOTES: 1 VACUUM PICKUP CELL LOCATION. 2 NON-BAKEABLE TRAYS SHOULD NOT BE EXPOSED TO TEMPERATURES GREATER THAN 50°C (122°F) AT ANY TIME. 3 INTERPRET DIMENSIONS AND TOLERANCES IN ACCORDANCE WITH ASME Y14.5M-1994. DETAIL B SCALE 4 : 1 4 UNLESS OTHERWISE NOTED 1°/2° DRAFT ON ALL VERTICAL SURFACE. 5 REVISION LEVEL AND DATE CODES WILL BE ON BOTTOM SIDE OF THE TRAY. WHEN POSSIBLE REVISION LEVEL WILL BE LOCATED NEAR 45° CHAMFER. 6 TRAY ESD 10e+5 - 10e+12 OHMS/SQ. 7 UNLESS SPECIFIED OTHERWISE, ELECTRONICALLY TRANSMITTED FILES ARE UNCONTROLLED DOCUMENTS. 8 TRAY COMPLIANT WITH JEDEC SPEC. DRAWN UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN MILLIMETERS Muda Alang ENGINEERED THIRD ANGLE PROJECTION APPROVED TOLERANCES: DECIMALS .X = .XX = .XXX = FRACTIONS ANGLES ±.5° 01/19/04 DATE John Ng 01/19/04 SM Lim PROJECT NO. DATE 02/07/06 SCALE T- 871 ±0.25 ±0.13 DATE SHEET 1 OF 3 1:1 SIZE DO NOT SCALE THIS DRAWING 8 7 6 5 4 3 2 D TITLE 3.4MM BODY CHIP 28 X 28 MQFP TRAY DRAWING NO. 3 X 8 MATRIX 4- 871 -15 1 REV A 8 7 6 5 4 3 2 1 THIS DOCUMENT CONTAINS CONFIDENTIAL, PROPRIETARY INFORMATION OF ITW CAMTEX IT MAY NOT BE REPRODUCED, DUPLICATED, OR DISCLOSED EXCEPT AS AUTHORIZED BY ITW CAMTEX C E E D D C SECTION C-C 32.80 +20 /S SQ. A B C W 0.88 0.12 SECTION D-D 1.00±0.08 4.60 0.50 M 0.80 27.75±0.08 +10 /S SQ. 3.80±0.08 28.63 +5 /S 25.15 -3 /S SQ. 29.52 ±0.08+7 /S SQ. 31.83 +3 /S SQ. 0.75 H H DETAIL W SCALE 10 : 1 SECTION E-E UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN MILLIMETERS THIRD ANGLE PROJECTION APPROVED TOLERANCES: SECTION H-H SCALE 3 : 1 8 7 6 5 4 DECIMALS .X = ± .25 .XX = ±.13 .XXX = 3 FRACTIONS A N G L E S ±.5° SM Lim TITLE DATE 02/07/06 SIZE SHEET 2 OF 3 D DO NOT SCALE THIS DRAWING 2 28 X 28 MQFP TRAY SCALE 4:1 3.4MM BODY CHIP DRAWING NO. 3 X 8 MATRIX 4- 871 -15 1 REV A 8 7 6 5 4 3 2 1 THIS DOCUMENT CONTAINS CONFIDENTIAL, PROPRIETARY INFORMATION OF ITW CAMTEX IT MAY NOT BE REPRODUCED, DUPLICATED, OR DISCLOSED EXCEPT AS AUTHORIZED BY ITW CAMTEX ISO ISO TOP DETAIL ISO TOP UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN MILLIMETERS DETAIL ISO BOTTOM THIRD ANGLE PROJECTION APPROVED TOLERANCES: DECIMALS .X = ± .25 .XX = ±.13 .XXX = 8 7 6 5 4 3 FRACTIONS A N G L E S ±.5° SM Lim TITLE DATE 02/07/06 SIZE SHEET 3 OF 3 D DO NOT SCALE THIS DRAWING 2 28 X 28 MQFP TRAY SCALE 4:1 3.4MM BODY CHIP DRAWING NO. 3 X 8 MATRIX 4- 871 -15 1 REV A