PDF Data Sheet Rev. C

1.5 GHz, Ultrahigh Speed Op Amp
AD8000
Data Sheet
FEATURES
CONNECTION DIAGRAMS
High speed
1.5 GHz, −3 dB bandwidth (G = +1)
650 MHz, full power bandwidth (G = +2, VO = 2 V p-p)
Slew rate: 4100 V/μs
0.1% settling time: 12 ns
Excellent video specifications
0.1 dB flatness: 170 MHz
Differential gain: 0.02%
Differential phase: 0.01°
Output overdrive recovery: 22 ns
Low noise: 1.6 nV/√Hz input voltage noise
Low distortion over wide bandwidth
75 dBc SFDR at 20 MHz
62 dBc SFDR at 50 MHz
Input offset voltage: 1 mV typical
High output current: 100 mA
Wide supply voltage range: 4.5 V to 12 V
Supply current: 13.5 mA
Power-down mode
AD8000
TOP VIEW
(Not to Scale)
POWER DOWN 1
6 NC
+IN 4
5 –VS
05321-001
7 OUTPUT
–IN 3
NOTES
1. NC = NO CONNECT.
2. THE EXPOSED PADDLE IS CONNECTED TO GROUND.
Figure 1. 8-Lead AD8000, 3 mm × 3 mm LFCSP (CP-8-13)
AD8000
FEEDBACK
1
8
POWER DOWN
–IN
2
7
+VS
+IN
3
6
OUTPUT
–VS
4
5
NC
NOTES
1. NC = NO CONNECT.
2. THE EXPOSED PADDLE IS CONNECTED TO GROUND.
05321-002
TOP VIEW
(Not to Scale)
Figure 2. 8-Lead AD8000 SOIC_N_EP (RD-8-1)
APPLICATIONS
Professional video
High speed instrumentation
Video switching
IF/RF gain stage
CCD imaging
The AD8000 power-down mode reduces the supply current to
1.3 mA. The amplifier is available in a tiny 8-lead LFCSP package,
as well as in an 8-lead SOIC package. The AD8000 is rated to work
over the extended industrial temperature range (−40°C to +125°C).
A triple version of the AD8000 (AD8003) is underdevelopment.
GENERAL DESCRIPTION
3
With a differential gain of 0.02%, differential phase of 0.01°, and
0.1 dB flatness out to 170 MHz, the AD8000 has excellent video
specifications, which ensure that even the most demanding
video systems maintain excellent fidelity.
1
0
–1
–2
–3
G = +2, RF = 432
–4
–5
05321-003
The AD8000 has low spurious-free dynamic range (SFDR) of
75 dBc at 20 MHz and input voltage noise of 1.6 nV/√Hz. The
AD8000 can drive over 100 mA of load current with minimal
distortion. The amplifier can operate on +5 V to ±6 V. These
specifications make the AD8000 ideal for a variety of applications, including high speed instrumentation.
VS = 5V
RL = 150
VOUT = 2V p-p
2
NORMALIZED GAIN (dB)
The AD8000 is an ultrahigh speed, high performance, current
feedback amplifier. Using Analog Devices, Inc., proprietary
eXtra Fast Complementary Bipolar (XFCB) process, the amplifier can achieve a small signal bandwidth of 1.5 GHz and a slew
rate of 4100 V/μs.
Rev. C
8 +VS
FEEDBACK 2
–6
–7
1
10
100
1000
FREQUENCY (MHz)
Figure 3. Large Signal Frequency Response
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2005–2016 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
AD8000
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1 Applications Information .............................................................. 14 Applications ....................................................................................... 1 Circuit Configurations .............................................................. 14 General Description ......................................................................... 1 Video Line Driver ....................................................................... 14 Connection Diagrams ...................................................................... 1 Low Distortion Pinout ............................................................... 15 Revision History ............................................................................... 2 Exposed Paddle........................................................................... 15 Specifications with ±5 V Supply ..................................................... 3 Printed Circuit Board Layout ................................................... 15 Specifications with +5 V Supply ..................................................... 4 Signal Routing............................................................................. 15 Absolute Maximum Ratings............................................................ 5 Power Supply Bypassing ............................................................ 15 Thermal Resistance ...................................................................... 5 Grounding ................................................................................... 16 Maximum Power Dissipation ..................................................... 5 Outline Dimensions ....................................................................... 17 ESD Caution .................................................................................. 5 Ordering Guide .......................................................................... 17 Typical Performance Characteristics ............................................. 6 Test Circuits ..................................................................................... 13 REVISION HISTORY
5/16—Rev. B to Rev. C
Changed CP-8-2 to CP-8-13 ........................................ Throughout
Updated Outline Dimensions ....................................................... 17
Changes to Ordering Guide .......................................................... 17
3/13—Rev. A to Rev. B
Changes to Figure 1 and Figure 2 ................................................... 1
Change to Table 1 ............................................................................. 3
Changes to Table2 ............................................................................. 4
Updated Outline Dimensions ....................................................... 17
Changes to Ordering Guide .......................................................... 17
3/10—Rev. 0 to Rev. A
Changes to Figure 1 and Figure 2 ................................................... 1
Changes to Table 3 ............................................................................ 5
Updated Outline Dimensions ....................................................... 17
Changes to Ordering Guide .......................................................... 17
1/05—Rev. 0: Initial Version
Rev. C | Page 2 of 17
Data Sheet
AD8000
SPECIFICATIONS WITH ±5 V SUPPLY
At TA = 25°C, VS = ±5 V, RL = 150 Ω, Gain = +2, RF = RG = 432 Ω, unless otherwise noted. Connect the exposed paddle to ground.
Table 1.
Parameter
DYNAMIC PERFORMANCE
−3 dB Bandwidth
Bandwidth for 0.1 dB Flatness
Slew Rate
Settling Time to 0.1%
NOISE/HARMONIC PERFORMANCE
Second/Third Harmonic
Second/Third Harmonic
Input Voltage Noise
Input Current Noise
Differential Gain Error
Differential Phase Error
DC PERFORMANCE
Input Offset Voltage
Input Offset Voltage Drift
Input Bias Current (Enabled)
Transimpedance
INPUT CHARACTERISTICS
Noninverting Input Impedance
Input Common-Mode Voltage Range
Common-Mode Rejection Ratio
Overdrive Recovery
POWER DOWN PIN
Power-Down Input Voltage
Turn-Off Time
Turn-On Time
Input Bias Current
Enabled
Power-Down
OUTPUT CHARACTERISTICS
Output Voltage Swing
Output Voltage Swing
Linear Output Current
Overdrive Recovery
POWER SUPPLY
Operating Range
Quiescent Current
Quiescent Current (Power-Down)
Power Supply Rejection Ratio
Test Conditions/Comments
Min
Typ
Max
Unit
G = +1, VO = 0.2 V p-p, SOIC/LFCSP
G = +2, VO = 2 V p-p, SOIC/LFCSP
VO = 2 V p-p, SOIC/LFCSP
G = +2, VO = 4 V step
G = +2, VO = 2 V step
1580/1350
650/610
190/170
4100
12
MHz
MHz
MHz
V/μs
ns
VO = 2 V p-p, f = 5 MHz, LFCSP only
VO = 2 V p-p, f = 20 MHz, LFCSP only
f = 100 kHz
f = 100 kHz, −IN
f = 100 kHz, +IN
NTSC, G = +2
NTSC, G = +2
86/89
75/79
1.6
26
3.4
0.02
0.01
dBc
dBc
nV/√Hz
pA/√Hz
pA/√Hz
%
Degree
+IB
−IB
570
VCM = ±2.5 V
G = +1, f = 1 MHz, triangle wave
−52
Power-down
Enabled
50% of power-down voltage to
10% of VOUT final, VIN = 0.3 V p-p
50% of power-down voltage to
90% of VOUT final, VIN = 0.3 V p-p
RL = 100 Ω
RL = 1 kΩ
VO = 2 V p-p, second HD < −50 dBc
G = + 2, f = 1 MHz, triangle wave
G = +2, VIN = 2.5 V to 0 V step
−PSRR/+PSRR
Rev. C | Page 3 of 17
1
11
−5
−3
890
2/3.6
−3.5 to +3.5
−54
30
+4
+45
1600
−56
mV
μV/°C
μA
μA
kΩ
MΩ/pF
V
dB
ns
< +VS – 3.1
> +VS – 1.9
150
V
V
ns
300
ns
−1.1
−300
+0.17
−235
±3.7
±3.9
±3.9
±4.1
100
45
22
4.5
12.7
1.1
−56/−61
10
13.5
1.3
−59/−63
+1.4
−160
μA
μA
V
V
mA
ns
ns
12
14.3
1.65
V
mA
mA
dB
AD8000
Data Sheet
SPECIFICATIONS WITH +5 V SUPPLY
At TA = 25°C, VS = 5 V, RL = 150 Ω, Gain = +2, RF = RG = 432 Ω, unless otherwise noted. Connect the exposed paddle to ground.
Table 2.
Parameter
DYNAMIC PERFORMANCE
−3 dB Bandwidth
Bandwidth for 0.1 dB Flatness
Slew Rate
Settling Time to 0.1%
NOISE/HARMONIC PERFORMANCE
Second/Third Harmonic
Second/Third Harmonic
Input Voltage Noise
Input Current Noise
Differential Gain Error
Differential Phase Error
DC PERFORMANCE
Input Offset Voltage
Input Offset Voltage Drift
Input Bias Current (Enabled)
Transimpedance
INPUT CHARACTERISTICS
Noninverting Input Impedance
Input Common-Mode Voltage Range
Common-Mode Rejection Ratio
Overdrive Recovery
POWER DOWN PIN
Power-Down Input Voltage
Turn-Off Time
Turn-On Time
Input Current
Enabled
Power-Down
OUTPUT CHARACTERISTICS
Output Voltage Swing
Linear Output Current
Overdrive Recovery
POWER SUPPLY
Operating Range
Quiescent Current
Quiescent Current (Power-Down)
Power Supply Rejection Ratio
Test Conditions/Comments
Min
Typ
Max
Unit
G = +1, VO = 0.2 V p-p
G = +2, VO = 2 V p-p
G = +10, VO = 0.2 V p-p
VO = 0.2 V p-p
VO = 2 V p-p
G = +2, VO = 2 V step
G = +2, VO = 2 V step
980
477
328
136
136
2700
16
MHz
MHz
MHz
MHz
MHz
V/μs
ns
VO = 2 V p-p, 5 MHz, LFCSP only
VO = 2 V p-p, 20 MHz, LFCSP only
f = 100 kHz
f = 100 kHz, −IN
f = 100 kHz, +IN
NTSC, G = +2
NTSC, G = +2
71/71
60/62
1.6
26
3.4
0.01
0.06
dBc
dBc
nV/√Hz
pA/√Hz
pA/√Hz
%
Degree
+IB
−IB
440
VCM = ±2.5 V
G = +1, f = 1 MHz, triangle wave
−51
Power-down
Enable
50% of power-down voltage to
10% of VOUT final, VIN = 0.3 V p-p
50% of power-down voltage to
90% of VOUT final, VIN = 0.3 V p-p
RL = 100 Ω
RL = 1 kΩ
VO = 2 V p-p, second HD < −50 dBc
G = +2, f = 100 kHz, triangle wave
−PSRR/+PSRR
Rev. C | Page 4 of 17
1.3
18
−5
−1
800
2/3.6
1.5 to 3.6
−52
60
+3
+45
1500
−54
mV
μV/°C
μA
μA
kΩ
MΩ/pF
V
dB
ns
< +VS − 3.1
> +VS − 1.9
200
V
V
ns
300
ns
−1.1
−50
+0.17
−40
1.1 to 3.9
1 to 4.0
1.05 to 4.1
0.85 to 4.15
70
65
4.5
11
0.7
−55/−60
10
12
0.95
−57/−62
+1.4
−30
μA
μA
V
V
mA
ns
12
13
1.25
V
mA
mA
dB
Data Sheet
AD8000
ABSOLUTE MAXIMUM RATINGS
V V
PD  VS  I S    S  OUT
RL
 2
Table 3.
Stresses at or above those listed under Absolute Maximum Ratings
may cause permanent damage to the product. This is a stress
rating only; functional operation of the product at these or any
other conditions above those indicated in the operational section of
this specification is not implied. Operation beyond the maximum
operating conditions for extended periods may affect product
reliability.
THERMAL RESISTANCE
θJA is specified for the worst-case conditions, that is, θJA is specified for device soldered in the circuit board for surface-mount
packages.
Consider the RMS output voltages. If RL is referenced to −VS, as
in single-supply operation, the total drive power is VS × IOUT. If
the rms signal levels are indeterminate, consider the worst case,
when VOUT = VS/4 for RL to midsupply.
PD  VS  I S  
θJA
80
93
θJC
30
35
Airflow increases heat dissipation, effectively reducing θJA. Also,
more metal directly in contact with the package leads and exposed
paddle from metal traces, through holes, ground, and power
planes reduces θJA.
Figure 4 shows the maximum safe power dissipation in the
package vs. the ambient temperature for the exposed paddle
SOIC (80°C/W) and the LFCSP (93°C/W) package on a JEDEC
standard 4-layer board. θJA values are approximations.
3.0
Unit
°C/W
°C/W
MAXIMUM POWER DISSIPATION
The maximum safe power dissipation for the AD8000 is limited
by the associated rise in junction temperature (TJ) on the die. At
approximately 150C, which is the glass transition temperature,
the properties of the plastic change. Even temporarily exceeding
this temperature limit can change the stresses that the package
exerts on the die, permanently shifting the parametric performance
of the AD8000. Exceeding a junction temperature of 175C for
an extended period of time can result in changes in silicon devices, potentially causing degradation or loss of functionality.
RL
In single-supply operation with RL referenced to −VS, worst case
is VOUT = VS/2.
Table 4. Thermal Resistance
Package Type
8-Lead SOIC
3 mm × 3 mm LFCSP
VS / 4 2
2.5
2.0
SOIC
1.5
LFCSP
1.0
0.5
05321-063
Rating
12.6 V
See Figure 4
−VS − 0.7 V to +VS + 0.7 V
VS
−65°C to +125°C
−40°C to +125°C
300°C
150°C
MAXIMUM POWER DISSIPATION (W)
Parameter
Supply Voltage
Power Dissipation
Common-Mode Input Voltage Range
Differential Input Voltage
Storage Temperature Range
Operating Temperature Range
Lead Temperature (Soldering, 10 sec)
Junction Temperature
 VOUT 2
–

RL

0
–40 –30 –20 –10
0
10
20
30
40
50
60
70
80
90 100 110 120
AMBIENT TEMPERATURE (C)
Figure 4. Maximum Power Dissipation vs. Temperature for a 4-Layer Board
ESD CAUTION
The power dissipated in the package (PD) is the sum of the quiescent power dissipation and the power dissipated in the die
due to the AD8000 drive at the output. The quiescent power is
the voltage between the supply pins (VS) times the quiescent
current (IS).
PD = Quiescent Power + (Total Drive Power − Load Power)
Rev. C | Page 5 of 17
AD8000
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
3
9
VS = 5V
RL = 150
VOUT = 200mV p-p
2
G = +1, RF = 432
RF = 392
6
0
–1
GAIN (dB)
G = +2, RF = 432, RG = 432
–2
–3
RF = 432
3
RF = 487
G = +10, RF = 357, RG = 40.2
–4
05321-006
–6
–7
1
10
100
–3
1
1000
10
1000
Figure 8. Small Signal Frequency Response vs. RF
Figure 5. Small Signal Frequency Response vs. Various Gains
9
3
VS = 5V
RL = 150
VOUT = 200mV p-p
2
1
G = –1, RF = RG = 249
RF = 392
6
0
–1
RF = 432
GAIN (dB)
–2
–3
3
RF = 487
G = –10, RF = 432, RG = 43.2
–4
05321-007
G = –2, RF = 432, RG = 215
–6
–7
1
10
100
05321-012
VS = 5V
G = +2
RL = 150
VOUT = 2V p-p
LFCSP
0
–5
–3
1
1000
10
100
1000
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 6. Small Signal Frequency Response vs. Various Gains
Figure 9. Large Signal Frequency Response vs. RF
3
1000
VS = 5V
RL = 150
VOUT = 2V p-p
1
200
VS = 5V
RL = 100
G = +1, RF = 432
150
TRANSIMPEDANCE (k)
2
0
–1
G = +4, RF = 357, RG = 121
–2
G = +10, RF = 357, RG = 40.2
–3
G = +2, RF = RG = 432
–4
100
100
10
50
PHASE
TZ
0
PHASE (Degrees)
NORMALIZED GAIN (dB)
100
FREQUENCY (MHz)
FREQUENCY (MHz)
1
–5
50
05321-008
NORMALIZED GAIN (dB)
05321-011
VS = 5V
G = +2
RL = 150
VOUT = 200mV p-p
LFCSP
0
–5
–6
–7
1
10
100
0.1
0.1
1000
FREQUENCY (MHz)
1
10
100
1000
100
10000
FREQUENCY (MHz)
Figure 7. Large Signal Frequency Response vs. Various Gains
Figure 10. Transimpedance and Phase vs. Frequency
Rev. C | Page 6 of 17
05321-027
NORMALIZED GAIN (dB)
1
Data Sheet
AD8000
9
3
RL = 1k
G = +1
RF = 432
VOUT = 200mV p-p
LFCSP
2
1
VS = +5V, RS = 0
6
–2
3
–40C
VS = +5V, RS = 50
–3
–4
VS = 5V
G = +2
RL = 150
VOUT = 200mV p-p
LFCSP
0
–5
05321-010
VS = 5V, RS = 50
–6
–7
0.1
1
10
100
05321-014
VS = 5V, RS = 0
–1
GAIN (dB)
GAIN (dB)
0
+125C
+25C
–3
1
1000
10
100
1000
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 14. Small Signal Frequency Response vs. Temperature
Figure 11. Small Signal Frequency Response vs. Supply Voltage
9
9
RL = 150
G = +1
RF = 432
VOUT = 200mV p-p
LFCSP
6
+25C
GAIN (dB)
GAIN (dB)
6
VS = 5V
3
0
–40C
3
VS = +5V
–3
VS = 5V
G = +2
RL = 1k
VOUT = 200mV p-p
LFCSP
05321-009
–9
1
10
100
+125C
05321-015
0
–6
–3
1
1000
10
100
1000
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 15. Small Signal Frequency Response vs. Temperature
Figure 12. Small Signal Frequency Response vs. Supply Voltage
9
6.5
VS = 5V
RL = 150
VOUT = 2V p-p
G = +2
RF = 432
6.4
6.3
6
GAIN (dB)
6.1
SOIC
6.0
5.9
3
–40C
LFCSP
+25C
VS = 5V
G = +2
RL = 150
VOUT = 2V p-p
LFCSP
0
5.7
5.6
5.5
1
10
+125C
05321-016
5.8
05321-013
GAIN (dB)
6.2
–3
1
100
10
100
1000
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 13. 0.1 dB Flatness
Figure 16. Large Signal Frequency Response vs. Temperature
Rev. C | Page 7 of 17
AD8000
Data Sheet
–40
9
VOUT = 1V p-p
–60
DISTORTION (dBc)
6
3
VOUT = 2V p-p
–3
1
10
SECOND HD
–80
–90
THIRD HD
–100
VOUT = 4V p-p
VS = 5V
G = +2
RL = 150
LFCSP
–70
–110
100
05321-042
0
05321-017
–120
1000
1
10
FREQUENCY (MHz)
Figure 17. Large Signal Frequency Response vs. Various Outputs
Figure 20. Harmonic Distortion vs. Frequency
–40
–20
VS = 5V
VOUT = 2V p-p
G = +1
RL = 150
LFCSP
–40
DISTORTION (dBc)
SECOND HD
–70
THIRD HD
–80
–90
–50
–70
THIRD HD
–80
–110
–90
–120
1
10
SECOND HD
–60
–100
05321-040
DISTORTION (dBc)
–60
VS = 5V
VOUT = 4V p-p
G = +1
RL = 1k
LFCSP
–30
05321-041
–50
–100
100
1
10
FREQUENCY (MHz)
100
FREQUENCY (MHz)
Figure 18. Harmonic Distortion vs. Frequency
Figure 21. Harmonic Distortion vs. Frequency
–40
–40
VS = 5V
G = +10
VOUT = 2V p-p
RL = 1k
LFCSP
–60
–70
VS = 5V
VOUT = 2V p-p
G = +2
RL = 150
–50
LFCSP SECOND HD
DISTORTION (dBc)
–50
SECOND HD
–80
THIRD HD
–90
–60
SOIC SECOND HD
–70
–80
–100
LFCSP THIRD HD
–90
–110
05321-039
DISTORTION (dBc)
100
FREQUENCY (MHz)
–120
1
10
SOIC THIRD HD
–100
1
100
10
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 22. Harmonic Distortion vs. Frequency
Figure 19. Harmonic Distortion vs. Frequency
Rev. C | Page 8 of 17
05321-043
GAIN (dB)
VS = 5V
VOUT = 2V p-p
G = +1
RL = 1k
LFCSP
–50
100
Data Sheet
AD8000
–20
–20
VS = 5V
VOUT = 2V p-p
G = +2
RL = 150
LFCSP
–40
SECOND HD
–50
–60
THIRD HD
–70
–80
–90
–50
–60
THIRD HD
–70
SECOND HD
–80
–90
05321-044
–100
–100
–110
1
10
05321-048
DISTORTION (dBc)
–40
VS = 2.5V
VOUT = 2V p-p
G = –1
RL = 150
LFCSP
–30
DISTORTION (dBc)
–30
–110
–120
1
100
10
Figure 23. Harmonic Distortion vs. Frequency
Figure 26. Harmonic Distortion vs. Frequency
–20
–20
VS = 5V
VOUT = 2V p-p
G = +2
RL = 1k
LFCSP
–40
–40
THIRD HD
–50
VS = 5V
VOUT = 2V p-p
G = –1
RL = 1k
LFCSP
–30
DISTORTION (dBc)
–30
DISTORTION (dBc)
100
FREQUENCY (MHz)
FREQUENCY (MHz)
–60
SECOND HD
–70
–50
THIRD HD
–60
–70
SECOND HD
–80
–90
–80
05321-045
–100
1
10
05321-049
–100
–90
–110
–120
100
1
10
FREQUENCY (MHz)
Figure 24. Harmonic Distortion vs. Frequency
–20
–40
–40
VS = 5V
VOUT = 2V p-p
G = –1
RL = 150
LFCSP
–50
–60
DISTORTION (dBc)
–50
SECOND HD
–60
–70
–80
THIRD HD
–90
SECOND HD
–70
THIRD HD
–80
–90
–100
–110
–120
1
10
05321-050
–100
05321-047
DISTORTION (dBc)
Figure 27. Harmonic Distortion vs. Frequency
VS = 5V
VOUT = 2V p-p
G = +2
RL = 1k
LFCSP
–30
100
FREQUENCY (MHz)
–110
1
100
10
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 28. Harmonic Distortion vs. Frequency
Figure 25. Harmonic Distortion vs. Frequency
Rev. C | Page 9 of 17
100
AD8000
–40
–10
VS = 5V
VOUT = 2V p-p
G = –1
RL = 1k
LFCSP
–50
–60
VS = 5V
VIN = 2V p-p
RL = 100
G = +1
RF = 432
–15
–20
–25
–PSRR
–30
SECOND HD
–70
PSRR (dB)
–80
THIRD HD
–90
–35
–40
+PSRR
–45
–50
–55
–100
–60
–65
05321-051
–110
–120
1
10
05321-021
DISTORTION (dBc)
Data Sheet
–70
–75
100
0.1
1
FREQUENCY (MHz)
Figure 29. Harmonic Distortion vs. Frequency
100
Figure 32. Power Supply Rejection Ratio (PSRR) vs. Frequency
1k
–25
VS = 5V
VIN = 0.2V p-p
RF = 432
LFCSP
100
10
FREQUENCY (MHz)
VS = 5V
VIN = 1V p-p
RL = 100
LFCSP
–30
10
CMRR (dB)
1
–40
–45
–50
–55
G = +1
OR G = +2
–60
05321-023
0.1
0.01
0.1
1
10
100
05321-031
IMPEDANCE ()
–35
–65
0.1
1000
1
10
FREQUENCY (MHz)
100
1000
FREQUENCY (MHz)
Figure 30. Output Impedance vs. Frequency
Figure 33. Common-Mode Rejection Ratio vs. Frequency
0.175
2.65
0.150
G = +1
G = +1
0.125
2.60
RESPONSE (V)
2.55
2.50
2.45
0.050
G = +2
0.025
0
–0.025
–0.050
VS = 5V
RF = 432
RS = 0
RL = 100
2.40
2.35
0
5
10
15
20
25
30
35
40
45
VS = 5V
RF = 432
RS = 0
RL = 100
–0.100
–0.125
–0.150
–0.175
50
0
5
10
15
20
25
30
35
40
TIME (ns)
TIME (ns)
Figure 34. Small Signal Transient Response
Figure 31. Small Signal Transient Response
Rev. C | Page 10 of 17
45
05321-066
–0.075
05321-072
RESPONSE (V)
0.100
0.075
G = +2
50
Data Sheet
AD8000
5
1.75
VS = 5V, VIN
1.50
4
G = +1
1.25
OUTPUT VOLTAGE (V)
0.75
0.50
G = +2
0.25
0
–0.25
–0.50
–0.75
VS = 5V
RF = 432
RS = 0
RL = 100
–1.25
–1.50
–1.75
0
5
10
15
20
25
30
35
40
45
1
VS = 2.5V, VOUT
0
–1
VS = 2.5V, VIN
–2
–3
05321-067
–1.00
2
G = +1
RL = 150
RF = 432
–4
05321-019
RESPONSE (V)
VS = 5V, VOUT
3
1.00
–5
0
50
200
400
600
800
1000
TIME (ns)
TIME (ns)
Figure 35. Large Signal Transient Response
Figure 38. Input Overdrive
6
0.5
G = +2
VS = 5V, 2  VIN
5
VIN
0.4
VS = 5V, VOUT
4
0.3
OUTPUT VOLTAGE (V)
SETTLING TIME (%)
3
1V
0.2
0.1
0
–0.1
–0.2
2
1
0
VS = 2.5V, 2  VIN
–1
–2
VS = 2.5V, VOUT
–3
05321-068
–4
–0.4
t = 0s
5ns/DIV
–0.5
–5
–4
–3
–2
–1
0
1
2
G = +2
RL = 150
RF = 432
–5
05321-020
–0.3
–6
3
0
200
400
800
1000
Figure 39. Output Overdrive
Figure 36. Settling Time
100
6k
G = +2
RF = 432
RL = 150
VS = 5V
G = +10
RF = 432
RN = 47.5
SOIC, VS = 5V
INPUT VOLTAGE NOISE (nV/ Hz)
5k
4k
LFCSP, VS = 5V
3k
SOIC, VS = +5V
2k
LFCSP, VS = +5V
10
1
0
0
1
2
3
4
5
6
0.1
10
7
05321-058
1k
05321-018
SR (V/s)
600
TIME (ns)
VCM (V)
100
1k
10k
100k
1M
FREQUENCY (Hz)
VOUT (V p-p)
Figure 37. Slew Rate vs. Output Level
Figure 40. Input Voltage Noise
Rev. C | Page 11 of 17
10M
100M
AD8000
1000
Data Sheet
0
VS = 5V
VS = 5V
–10
100
VS = +5V
–15
INVERTING CURRENT NOISE, RF = 1k
IB (A)
–20
10
–25
–30
–35
1
0.1
10
100
1k
10k
100k
1M
10M
100M
05321-070
–40
NONINVERTING CURRENT NOISE, RF = 432
05321-055
INPUT CURRENT NOISE (pA/ Hz)
–5
–45
–50
1G
–5
–4
–3
–2
FREQUENCY (Hz)
1
2
3
4
5
Figure 44. Input Bias Current vs. Common-Mode Voltage
20
–5
15
–10
RBACK TERM = 50
VS = 5V
G = +2
POUT = –10dBm
SOIC
–15
10
–20
VS = 5V
S22 (dB)
VOS (mV)
0
VCM (V)
Figure 41. Input Current Noise
5
–1
0
–25
–30
–5
–35
–10
VS = +5V
–20
–5
–4
–3
–2
–1
0
1
2
3
4
05321-065
05321-024
–40
–15
–45
–50
5
10
VCM (V)
1000
Figure 45. Output Voltage Standing Wave Ratio (S22)
Figure 42. Input VOS vs. Common-Mode Voltage
25
–5
20
–10
15
G = +10
–15
G = +2
10
–20
S11 (dB)
5
VS = 5V
0
–5
–25
G = +1
–30
–20
–25
–5
–4
–3
–2
–1
0
1
2
INPUT RS = 0
VS = 5V
POUT = –10dBm
SOIC
–40
VS = +5V
–15
3
4
–45
–50
5
10
VOUT (V)
100
FREQUENCY (MHz)
Figure 46. Input Voltage Standing Wave Ratio (S11)
Figure 43. Input Bias Current vs. Output Voltage
Rev. C | Page 12 of 17
05321-064
–35
–10
05321-069
IB (A)
100
FREQUENCY (MHz)
1000
Data Sheet
AD8000
TEST CIRCUITS
+VS
10F
0.1F
RF
432
50
TRANSMISSION
LINE
AD8000
432
50
TRANSMISSION
LINE
49.9
VIN
60.4
200
49.9
200
05321-028
0.1F
10F
–VS
Figure 47. CMRR
VP = VS + VIN
49.9
50
TRANSMISSION
LINE
TERMINATION
50
AD8000
50
TRANSMISSION
LINE
49.9
49.9
RF
432
TERMINATION
50
0.1F
RG
432
05321-029
10F
–VS
Figure 48. Positive PSRR
+VS
10F
0.1F
TERMINATION
50
AD8000
50
TRANSMISSION
LINE
49.9
49.9
TERMINATION
50
RF
432
RG
432
49.9
VN = –VS + VIN
Figure 49. Negative PSRR
Rev. C | Page 13 of 17
05321-030
50
TRANSMISSION
LINE
AD8000
Data Sheet
APPLICATIONS INFORMATION
+VS
All current feedback amplifier operational amplifiers are affected
by stray capacitance at the inverting input pin. As a practical
consideration, the higher the stray capacitance on the inverting
input to ground, the higher RF needs to be to minimize peaking
and ringing.
0.1F
FB
RG
VIN
AD8000
Table 5 provides a quick reference for the circuit values, gain,
and output voltage noise.
+VS
10F
+
–VS
Figure 51. Inverting Configuration
VIDEO LINE DRIVER
The AD8000 is designed to offer outstanding performance as a
video line driver. The important specifications of differential
gain (0.02%), differential phase (0.01°), and 650 MHz bandwidth at
2 V p-p meet the most exacting video demands. Figure 52 shows a
typical noninverting video driver with a gain of +2.
432
432
+VS
FB
4.7F
+
+V
–
AD8000
FB
VO
+
–V
05321-036
10F
+
VO
75
RL
VOUT
0.1F
+
75
CABLE
10F
+
–VS
75
05321-035
75
4.7F
VIN
NONINVERTING
75
CABLE
AD8000
0.1F
–VS
0.1F
+
05321-071
RS
RL
–V 0.1F
0.1F
VIN
VO
VO
+
Figure 50 and Figure 51 show typical schematics for noninverting
and inverting configurations. For current feedback amplifiers,
the value of feedback resistance determines the stability and
bandwidth of the amplifier. The optimum performance values
are shown in Table 5 and should not be deviated from by more
than ±10% to ensure stable operation. Figure 8 shows the influence
varying RF has on bandwidth. In noninverting unity-gain
configurations, it is recommended that an RS of 50 Ω be used,
as shown in Figure 50.
RG
+V
–
CIRCUIT CONFIGURATIONS
RF
10F
+
RF
Figure 52. Video Line Driver
Figure 50. Noninverting Configuration
Table 5. Typical Values (LFCSP/SOIC)
Gain
1
2
4
10
Component
Values (Ω)
RG
RF
432
432
432
357
120
357
40
−3 dB SS Bandwidth
(MHz)
LFCSP
SOIC
1380
1580
600
650
550
550
350
365
−3 dB LS Bandwidth
(MHz)
LFCSP
SOIC
550
600
610
650
350
350
370
370
Slew Rate
(V/μs)
Output Noise
(nV/√Hz)
Total Output Noise Including
Resistors (nV/√Hz)
2200
3700
3800
3200
10.9
11.3
10
18.4
11.2
11.9
12
19.9
Rev. C | Page 14 of 17
Data Sheet
AD8000
LOW DISTORTION PINOUT
PRINTED CIRCUIT BOARD LAYOUT
The AD8000 LFCSP features Analog Devices low distortion
pinout. The new pinout lowers the second harmonic distortion
and simplifies the circuit layout. The close proximity of the
non-inverting input and the negative supply pin creates a source
of second harmonic distortion. Physical separation of the noninverting input pin and the negative power supply pin reduces
this distortion significantly, as seen in Figure 22.
Laying out the printed circuit board (PCB) is usually the last
step in the design process and often proves to be one of the
most critical. A brilliant design can be rendered useless because
of a poor or sloppy layout. Because the AD8000 can operate
into the RF frequency spectrum, high frequency board layout
considerations must be taken into account. The PCB layout,
signal routing, power supply bypassing, and grounding all must
be addressed to ensure optimal performance.
By providing an additional output pin, the feedback resistor can
be connected directly across Pin 2 and Pin 3. This greatly simplifies
the routing of the feedback resistor and allows a more compact
circuit layout, which reduces its size and helps to minimize
parasitics and increase stability.
The SOIC also features a dedicated feedback pin. The feedback
pin is brought out on Pin 1, which is typically a no connect on
standard SOIC pinouts.
Existing applications that use the standard SOIC pinout can
take full advantage of the performance offered by the AD8000.
For drop-in replacements, ensure that Pin 1 is not connected to
ground or to any other potential because this pin is connected
internally to the output of the amplifier. For existing designs,
Pin 6 can still be used for the feedback resistor.
EXPOSED PADDLE
The AD8000 features an exposed paddle, which can lower the
thermal resistance by 25% compared to a standard SOIC plastic
package. The paddle can be soldered directly to the ground plane
of the board. Figure 53 shows a typical pad geometry for the LFCSP,
the same type of pad geometry can be applied to the SOIC package.
05321-034
Thermal vias or heat pipes can also be incorporated into the design
of the mounting pad for the exposed paddle. These additional
vias improve the thermal transfer from the package to the PCB.
Using a heavier weight copper on the surface to which the exposed
paddle of the amplifier is soldered also reduces the overall
thermal resistance seen by the AD8000.
Figure 53. LFCSP Exposed Paddle Layout
SIGNAL ROUTING
The AD8000 LFCSP features the new low distortion pinout with a
dedicated feedback pin and allows a compact layout. The dedicated
feedback pin reduces the distance from the output to the inverting
input, which greatly simplifies the routing of the feedback network.
To minimize parasitic inductances, use ground planes under
high frequency signal traces. However, remove the ground
plane from under the input and output pins to minimize the
formation of parasitic capacitors, which degrades phase margin.
Run signals that are susceptible to noise pickup on the internal
layers of the PCB, which can provide maximum shielding.
POWER SUPPLY BYPASSING
Power supply bypassing is a critical aspect of the PCB design
process. For best performance, the AD8000 power supply pins
need to be properly bypassed.
A parallel connection of capacitors from each of the power supply
pins to ground works best. Paralleling different values and sizes
of capacitors helps to ensure that the power supply pins see a
low ac impedance across a wide band of frequencies. This is
important for minimizing the coupling of noise into the amplifier.
Starting directly at the power supply pins, place the smallest
value and sized component on the same side of the board as the
amplifier, and as close as possible to the amplifier, and connected
to the ground plane. Repeat this process for the next larger value
capacitor. It is recommended for the AD8000 that a 0.1 μF ceramic
0508 case be used. The 0508 offers low series inductance and
excellent high frequency performance. The 0.1 μF case provides
low impedance at high frequencies. Place a 10 μF electrolytic
capacitor in parallel with the 0.1 μF. The 10 μF capacitor provides
low ac impedance at low frequencies. Smaller values of electrolytic
capacitors can be used, depending on the circuit requirements.
Additional smaller value capacitors help to provide a low
impedance path for unwanted noise out to higher frequencies
but are not always necessary.
Placement of the capacitor returns (grounds), where the capacitors
enter into the ground plane, is also important. Returning the
capacitors grounds close to the amplifier load is critical for
distortion performance. Keeping the capacitors distance short,
but equal from the load, is optimal for performance.
Rev. C | Page 15 of 17
AD8000
Data Sheet
In some cases, bypassing between the two supplies can help to
improve PSRR and to maintain distortion performance in
crowded or difficult layouts. This is as another option to
improve performance.
Minimizing the trace length and widening the trace from the
capacitors to the amplifier reduce the trace inductance. A series
inductance with the parallel capacitance can form a tank circuit,
which can introduce high frequency ringing at the output. This
additional inductance can also contribute to increased distortion due to high frequency compression at the output. Minimize
the use of vias in the direct path to the amplifier power supply
pins because vias can introduce parasitic inductance, which can
lead to instability. When required, use multiple large diameter
vias because this lowers the equivalent parasitic inductance.
GROUNDING
The use of ground and power planes is encouraged as a method
of proving low impedance returns for power supply and signal
currents. Ground and power planes can also help to reduce
stray trace inductance and to provide a low thermal path for the
amplifier. Do not use ground and power planes under any of the
pins of the AD8000. The mounting pads and the ground or
power planes can form a parasitic capacitance at the amplifiers
input. Stray capacitance on the inverting input and the feedback
resistor form a pole, which degrades the phase margin, leading
to instability. Excessive stray capacitance on the output also
forms a pole, which degrades phase margin.
Rev. C | Page 16 of 17
Data Sheet
AD8000
OUTLINE DIMENSIONS
5.00
4.90
4.80
2.29
0.356
8
5
1
4
6.20
6.00
5.80
4.00
3.90
3.80
2.29
0.457
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
BOTTOM VIEW
1.27 BSC
3.81 REF
TOP VIEW
SEATING
PLANE
0.50
0.25
0.10 MAX
0.05 NOM
COPLANARITY
0.10
0.51
0.31
8°
0°
45°
0.25
0.17
1.04 REF
1.27
0.40
06-02-2011-B
1.65
1.25
1.75
1.35
COMPLIANT TO JEDEC STANDARDS MS-012-A A
Figure 54. 8-Lead Standard Small Outline Package, with Exposed Pad [SOIC_N_EP]
Narrow Body
(RD-8-1)
Dimensions shown in millimeters
1.84
1.74
1.64
3.10
3.00 SQ
2.90
0.50 BSC
8
5
1.55
1.45
1.35
EXPOSED
PAD
0.50
0.40
0.30
0.80
0.75
0.70
SEATING
PLANE
1
4
BOTTOM VIEW
TOP VIEW
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.203 REF
0.30
0.25
0.20
PIN 1
INDICATOR
(R 0.15)
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
12-07-2010-A
PIN 1 INDEX
AREA
COMPLIANT TO JEDEC STANDARDS MO-229-WEED
Figure 55. 8-Lead Lead Frame Chip Scale Package [LFCSP]
3 mm × 3 mm Body and 0.75 mm Package Height
(CP-8-13)
Dimensions shown in millimeters
ORDERING GUIDE
Model1
AD8000YRDZ
AD8000YRDZ-REEL7
AD8000YCPZ-R2
AD8000YCPZ-REEL
AD8000YCPZ-REEL7
1
Temperature Range
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
Package Description
8-Lead SOIC_N_EP
8-Lead SOIC_N_EP
8-Lead LFCSP
8-Lead LFCSP
8-Lead LFCSP
Package Option
RD-8-1
RD-8-1
CP-8-13
CP-8-13
CP-8-13
Z = RoHS Compliant Part.
©2005–2016 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D05321-0-5/16(C)
Rev. C | Page 17 of 17
Branding
HNB
HNB
HNB
Ordering Quantity
1
1,000
250
5,000
1,500