25LC512 512 Kbit SPI Bus Serial EEPROM Extended (M) Operating Temperatures Device Selection Table Part Number 25LC512 VCC Range Page Size Temp. Ranges Packages 2.5-5.5V 128 Byte -55°C to +125°C (M) SN Features: Description: • 10 MHz max. Clock Speed • Byte and Page-level Write Operations: - 128-byte page - 5 ms max. - No page or sector erase required • Low-Power CMOS Technology: - Max. Write Current: 7 mA at 5.5V - Read Current: 10 mA at 5.5V, 10 MHz - Standby Current: 1 A at 2.5V, 85°C (Deep power-down) • Electronic Signature for Device ID • Self-Timed Erase and Write Cycles: - Page Erase (5 ms, typical) - Sector Erase (10 ms/sector, typical) - Bulk Erase (10 ms, typical) • Sector Write Protection (16K byte/sector): - Protect none, 1/4, 1/2 or all of array • Built-In Write Protection: - Power-on/off data protection circuitry - Write enable latch - Write-protect pin • High Reliability: - Endurance: 1 Million erase/write cycles - Data Retention: >200 years - ESD Protection: >4000V • Temperature Ranges Supported: - Extended (M): -55C to +125C The Microchip Technology Inc. 25LC512 is a 512 Kbit serial EEPROM memory with byte-level and page-level serial EEPROM functions. It also features Page, Sector and Chip erase functions typically associated with Flash-based products. These functions are not required for byte or page write operations. The memory is accessed via a simple Serial Peripheral Interface (SPI) compatible serial bus. The bus signals required are a clock input (SCK) plus separate data in (SI) and data out (SO) lines. Access to the device is controlled by a Chip Select (CS) input. Communication to the device can be paused via the hold pin (HOLD). While the device is paused, transitions on its inputs will be ignored, with the exception of Chip Select, allowing the host to service higher priority interrupts. The 25LC512 is available in the 8-lead SOIC package. Package Types (not to scale) CS SO 1 2 WP 3 VSS 4 25LC512 SOIC (SN) 8 7 VCC HOLD 6 SCK 5 SI • RoHS Compliant Pin Function Table Name Function CS SO Chip Select Input Serial Data Output WP VSS SI SCK Write-Protect Ground Serial Data Input Serial Clock Input HOLD VCC Hold Input Supply Voltage 2014 Microchip Technology Inc. DS20005265A-page 1 25LC512 1.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings (†) VCC .............................................................................................................................................................................6.5V All inputs and outputs w.r.t. VSS ......................................................................................................... -0.6V to VCC +1.0V Storage temperature .................................................................................................................................-65°C to 150°C Ambient temperature under bias ...............................................................................................................-55°C to 125°C ESD protection on all pins ..........................................................................................................................................4 kV † NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for an extended period of time may affect device reliability. TABLE 1-1: DC CHARACTERISTICS DC CHARACTERISTICS Param. No. Sym. Characteristic Extended (M): TA = -55°C to +125°C Min. Max. Units VCC = 2.5V to 5.5V Test Conditions D001 VIH1 High-level input voltage 0.7 VCC VCC + 1 V — D002 VIL1 0.3 VCC V VCC2.7V D003 Low-level input voltage -0.3 VIL2 -0.3 0.2 VCC V VCC < 2.7V D004 VOL Low-level output voltage — 0.4 V IOL = 2.1 mA D005 VOH High-level output voltage VCC - 0.2 — V IOH = -400 A D006 ILI Input leakage current — ±1 A CS = VCC, VIN = VSS or VCC D007 ILO Output leakage current — ±1 A CS = VCC, VOUT = VSS or VCC D008 CINT Internal capacitance (all inputs and outputs) — 7 pF TA = 25°C, CLK = 1.0 MHz, VCC = 5.0V (Note) D009 ICC Read — 10 mA — 5 mA VCC = 5.5V; FCLK = 10.0 MHz; SO = Open VCC = 2.5V; FCLK = 10.0 MHz; SO = Open — — 7 5 mA mA VCC = 5.5V VCC = 2.5V — 20 A — 10 A CS = VCC = 5.5V, Inputs tied to VCC or VSS, 125°C CS = VCC = 5.5V, Inputs tied to VCC or VSS, 85°C — 2 A 1 A Operating current D010 ICC Write D011 ICCS Standby current D012 Note: ICCSPD Deep power-down current CS = VCC = 2.5V, Inputs tied to VCC or VSS, 125°C CS = VCC = 2.5V, Inputs tied to VCC or VSS, 85°C This parameter is periodically sampled and not 100% tested. DS20005265A-page 2 2014 Microchip Technology Inc. 25LC512 TABLE 1-2: AC CHARACTERISTICS AC CHARACTERISTICS Param. No. Sym. Extended (M): Characteristic TA = -55°C to +125°C Min. Max. Units VCC = 2.5V to 5.5V Conditions 1 FCLK Clock frequency — 10 MHz — 2 TCSS CS setup time 50 — ns — 3 TCSH CS hold time 100 — ns — 4 TCSD CS disable time 50 — ns — 5 Tsu Data setup time 10 — ns — 6 THD Data hold time 20 — ns — 7 TR CLK rise time — 20 ns (Note 1) 8 TF CLK fall time — 20 ns (Note 1) 9 THI Clock high time 50 — ns — 10 TLO Clock low time 50 — ns — 11 TCLD Clock delay time 50 — ns — 12 TCLE Clock enable time 50 — ns — 13 TV Output valid from clock low — 50 ns — 14 THO Output hold time 0 — ns (Note 1) 15 TDIS Output disable time — 50 ns — 16 THS HOLD setup time 20 — ns — 17 THH HOLD hold time 20 — ns — 18 THZ HOLD low to output High-Z 30 — ns (Note 1) 19 THV HOLD high to output valid 30 — ns — 20 TREL CS High to Standby mode — 100 s — 21 TPD CS High to Deep powerdown — 100 s — 22 TCE Chip erase cycle time — 10 ms — 23 TSE Sector erase cycle time — 10 ms — 24 TWC Internal write cycle time — 5 ms Byte or Page mode and Page Erase 25 — Endurance 1M — E/W Page mode, 25°C, 5.5V (Note 2) Cycles Note 1: This parameter is periodically sampled and not 100% tested. 2: This parameter is not tested but established by characterization and qualification. For endurance estimates in a specific application, please consult the Total Endurance™ Model, which can be obtained from Microchip’s web site at www.microchip.com. 2014 Microchip Technology Inc. DS20005265A-page 3 25LC512 TABLE 1-3: AC TEST CONDITIONS AC Waveform: VLO = 0.2V — VHI = VCC - 0.2V (Note 1) VHI = 4.0V (Note 2) CL = 30 pF — Timing Measurement Reference Level Input 0.5 VCC Output 0.5 VCC Note 1: For VCC 4.0V 2: For VCC > 4.0V FIGURE 1-1: HOLD TIMING CS 16 17 16 17 16 17 16 17 SCK 18 n n+1 SO High-Impedance Don’t Care SI 19 n-1 High-Impedance 19 n-2 Don’t Care 5 n n+1 18 n n-1 n n-2 HOLD FIGURE 1-2: SERIAL INPUT TIMING 4 CS 2 7 Mode 1,1 8 3 12 11 SCK Mode 0,0 5 SI SO DS20005265A-page 4 6 MSB in LSB in High-Impedance 2014 Microchip Technology Inc. 25LC512 FIGURE 1-3: SERIAL OUTPUT TIMING CS 9 3 10 Mode 1,1 SCK Mode 0,0 13 SO 14 MSB out SI 2014 Microchip Technology Inc. 15 LSB out Don’t Care DS20005265A-page 5 25LC512 2.0 FUNCTIONAL DESCRIPTION 2.1 Principles of Operation BLOCK DIAGRAM The 25LC512 is a 65,536 byte Serial EEPROM designed to interface directly with the Serial Peripheral Interface (SPI) port of many of today’s popular microcontroller families, including Microchip’s PIC® microcontrollers. It may also interface with microcontrollers that do not have a built-in SPI port by using discrete I/O lines programmed properly in firmware to match the SPI protocol. The 25LC512 contains an 8-bit instruction register. The device is accessed via the SI pin, with data being clocked in on the rising edge of SCK. The CS pin must be low and the HOLD pin must be high for the entire operation. Table 2-1 contains a list of the possible instruction bytes and format for device operation. All instructions, addresses, and data are transferred MSB first, LSB last. Data (SI) is sampled on the first rising edge of SCK after CS goes low. If the clock line is shared with other peripheral devices on the SPI bus, the user can assert the HOLD input and place the 25LC512 in ‘HOLD’ mode. After releasing the HOLD pin, operation will resume from the point when the HOLD was asserted. TABLE 2-1: STATUS Register I/O Control Logic HV Generator Memory Control Logic EEPROM Array X Dec Page Latches SI SO Y Decoder CS SCK Sense Amp. R/W Control HOLD WP VCC VSS INSTRUCTION SET Instruction Name Instruction Format Description READ 0000 0011 Read data from memory array beginning at selected address WRITE 0000 0010 Write data to memory array beginning at selected address WREN 0000 0110 Set the write enable latch (enable write operations) WRDI 0000 0100 Reset the write enable latch (disable write operations) RDSR 0000 0101 Read STATUS register WRSR 0000 0001 Write STATUS register PE 0100 0010 Page Erase – erase one page in memory array SE 1101 1000 Sector Erase – erase one sector in memory array CE 1100 0111 Chip Erase – erase all sectors in memory array RDID 1010 1011 Release from Deep power-down and read electronic signature DPD 1011 1001 Deep Power-Down mode DS20005265A-page 6 2014 Microchip Technology Inc. 25LC512 Read Sequence The device is selected by pulling CS low. The 8-bit READ instruction is transmitted to the 25LC512 followed by the 16-bit address. After the correct READ instruction and address are sent, the data stored in the memory at the selected address is shifted out on the SO pin. The data stored in the memory at the next address can be read sequentially by continuing to FIGURE 2-1: provide clock pulses. The internal Address Pointer is automatically incremented to the next higher address after each byte of data is shifted out. When the highest address is reached (FFFFh), the address counter rolls over to address 0000h allowing the read cycle to be continued indefinitely. The READ instruction is terminated by raising the CS pin (Figure 2-1). READ SEQUENCE CS 0 1 2 3 4 5 6 7 8 9 10 11 21 22 23 24 25 26 27 28 29 30 31 SCK Instruction SI 0 0 0 0 0 16-bit Address 0 1 1 15 14 13 12 2 1 0 Data Out High-Impedance SO 2014 Microchip Technology Inc. 7 6 5 4 3 2 1 0 DS20005265A-page 7 25LC512 2.2 Write Sequence Note: Page write operations are limited to writing bytes within a single physical page, regardless of the number of bytes actually being written. Physical page boundaries start at addresses that are integer multiples of the page buffer size (or ‘page size’), and end at addresses that are integer multiples of page size – 1. If a Page Write command attempts to write across a physical page boundary, the result is that the data wraps around to the beginning of the current page (overwriting data previously stored there), instead of being written to the next page as might be expected. It is, therefore, necessary for the application software to prevent page write operations that would attempt to cross a page boundary. Prior to any attempt to write data to the 25LC512, the write enable latch must be set by issuing the WREN instruction (Figure 2-4). This is done by setting CS low and then clocking out the proper instruction into the 25LC512. After all eight bits of the instruction are transmitted, the CS must be brought high to set the write enable latch. If the write operation is initiated immediately after the WREN instruction without CS being brought high, the data will not be written to the array because the write enable latch will not have been properly set. A write sequence includes an automatic, self timed erase cycle. It is not required to erase any portion of the memory prior to issuing a WRITE instruction. Once the write enable latch is set, the user may proceed by setting the CS low, issuing a WRITE instruction, followed by the 16-bit address, and then the data to be written. Up to 128 bytes of data can be sent to the device before a write cycle is necessary. The only restriction is that all of the bytes must reside in the same page. Note: When doing a write of less than 128 bytes the data in the rest of the page is refreshed along with the data bytes being written. This will force the entire page to endure a write cycle, for this reason endurance is specified per page. FIGURE 2-2: For the data to be actually written to the array, the CS must be brought high after the Least Significant bit (D0) of the nth data byte has been clocked in. If CS is brought high at any other time, the write operation will not be completed. Refer to Figure 2-2 and Figure 2-3 for more detailed illustrations on the byte write sequence and the page write sequence, respectively. While the write is in progress, the STATUS register may be read to check the status of the WPEN, WIP, WEL, BP1 and BP0 bits (Figure 2-6). A read attempt of a memory array location will not be possible during a write cycle. When the write cycle is completed, the write enable latch is reset. BYTE WRITE SEQUENCE CS Twc 0 1 2 0 0 0 3 4 5 6 7 8 9 10 11 0 1 0 15 14 13 12 21 22 23 24 25 26 27 28 29 30 31 SCK Instruction SI 0 0 16-bit Address Data Byte 2 1 0 7 6 5 4 3 2 1 0 High-Impedance SO DS20005265A-page 8 2014 Microchip Technology Inc. 25LC512 FIGURE 2-3: PAGE WRITE SEQUENCE CS 0 1 2 0 0 0 3 4 5 6 7 8 9 10 11 21 22 23 24 25 26 27 28 29 30 31 SCK Instruction SI 0 0 16-bit Address 0 1 0 15 14 13 12 Data Byte 1 2 1 0 7 6 5 4 3 2 1 0 CS 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 SCK Data Byte 2 SI 7 6 5 4 2014 Microchip Technology Inc. 3 2 Data Byte n (128 max) Data Byte 3 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 DS20005265A-page 9 25LC512 2.3 Write Enable (WREN) and Write Disable (WRDI) • • • • • • • The 25LC512 contains a write enable latch. See Table 2-4 for the Write-Protect Functionality Matrix. This latch must be set before any write operation will be completed internally. The WREN instruction will set the latch, and the WRDI will reset the latch. Power-up WRDI instruction successfully executed WRSR instruction successfully executed WRITE instruction successfully executed PE instruction successfully executed SE instruction successfully executed CE instruction successfully executed The following is a list of conditions under which the write enable latch will be reset: FIGURE 2-4: WRITE ENABLE SEQUENCE (WREN) CS 0 1 2 3 4 5 6 7 SCK 0 SI 0 0 0 1 1 0 High-Impedance SO FIGURE 2-5: 0 WRITE DISABLE SEQUENCE (WRDI) CS 0 1 2 3 4 5 6 7 SCK SI 0 0 0 0 0 1 10 0 High-Impedance SO DS20005265A-page 10 2014 Microchip Technology Inc. 25LC512 2.4 Read Status Register Instruction (RDSR) The Write Enable Latch (WEL) bit indicates the status of the write enable latch and is read-only. When set to a ‘1’, the latch allows writes to the array, when set to a ‘0’, the latch prohibits writes to the array. The state of this bit can always be updated via the WREN or WRDI commands regardless of the state of write protection on the STATUS register. These commands are shown in Figure 2-4 and Figure 2-5. The Read Status Register instruction (RDSR) provides access to the STATUS register. The STATUS register may be read at any time, even during a write cycle. The STATUS register is formatted as follows: TABLE 2-2: STATUS REGISTER 7 6 5 4 3 2 1 W/R – – – W/R W/R R WPEN X X X BP1 BP0 WEL W/R = writable/readable. R = read-only. The Block Protection (BP0 and BP1) bits indicate which blocks are currently write-protected. These bits are set by the user issuing the WRSR instruction. These bits are nonvolatile, and are shown in Table 2-3. 0 R WIP See Figure 2-6 for the RDSR timing sequence. The Write-In-Process (WIP) bit indicates whether the 25LC512 is busy with a write operation. When set to a ‘1’, a write is in progress, when set to a ‘0’, no write is in progress. This bit is read-only. FIGURE 2-6: READ STATUS REGISTER TIMING SEQUENCE (RDSR) CS 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 1 0 SCK Instruction SI 0 0 0 0 0 High-Impedance SO 2014 Microchip Technology Inc. 1 0 1 Data from STATUS Register 7 6 5 4 3 2 DS20005265A-page 11 25LC512 2.5 Write Status Register Instruction (WRSR) The Write-Protect Enable (WPEN) bit is a nonvolatile bit that is available as an enable bit for the WP pin. The Write-Protect (WP) pin and the Write-Protect Enable (WPEN) bit in the STATUS register control the programmable hardware write-protect feature. Hardware write protection is enabled when WP pin is low and the WPEN bit is high. Hardware write protection is disabled when either the WP pin is high or the WPEN bit is low. When the chip is hardware write-protected, only writes to nonvolatile bits in the STATUS register are disabled. See Table 2-4 for a matrix of functionality on the WPEN bit. The Write Status Register instruction (WRSR) allows the user to write to the nonvolatile bits in the STATUS register as shown in Table 2-2. The user is able to select one of four levels of protection for the array by writing to the appropriate bits in the STATUS register. The array is divided up into four segments. The user has the ability to write-protect none, one, two or all four of the segments of the array. The partitioning is controlled as shown in Table 2-3. See Figure 2-7 for the WRSR timing sequence. TABLE 2-3: ARRAY PROTECTION BP1 BP0 Array Addresses Write-Protected Array Addresses Unprotected 0 0 none All (Sectors 0, 1, 2 & 3) (0000h-FFFFh) 0 1 Upper 1/4 (Sector 3) (C000h-FFFFh) Lower 3/4 (Sectors 0, 1 & 2) (0000h-BFFFh) 1 0 Upper 1/2 (Sectors 2 & 3) (8000h-FFFFh) Lower 1/2 (Sectors 0 & 1) (0000h-7FFFh) 1 1 All (Sectors 0, 1, 2 & 3) (0000h-FFFFh) none FIGURE 2-7: WRITE STATUS REGISTER TIMING SEQUENCE (WRSR) CS 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 1 0 SCK Instruction SI 0 0 0 0 Data to STATUS Register 0 0 0 1 7 6 5 4 3 2 High-Impedance SO DS20005265A-page 12 2014 Microchip Technology Inc. 25LC512 2.6 Data Protection 2.7 The following protection has been implemented to prevent inadvertent writes to the array: • The write enable latch is reset on power-up • A write enable instruction must be issued to set the write enable latch • After a byte write, page write or STATUS register write, the write enable latch is reset • CS must be set high after the proper number of clock cycles to start an internal write cycle • Access to the array during an internal write cycle is ignored and programming is continued TABLE 2-4: Power-On State The 25LC512 powers on in the following state: • The device is in low-power Standby mode (CS = 1) • The write enable latch is reset • SO is in high-impedance state • A high-to-low-level transition on CS is required to enter active state WRITE-PROTECT FUNCTIONALITY MATRIX WEL (SR bit 1) WPEN (SR bit 7) WP (pin 3) Protected Blocks Unprotected Blocks STATUS Register 0 x x Protected Protected Protected 1 0 x Protected Writable Writable 1 1 0 (low) Protected Writable Protected 1 1 1 (high) Protected Writable Writable x = don’t care 2014 Microchip Technology Inc. DS20005265A-page 13 25LC512 2.8 PAGE ERASE CS must then be driven high after the last bit of the address or the PAGE ERASE will not execute. Once the CS is driven high the self-timed PAGE ERASE cycle is started. The WIP bit in the STATUS register can be read to determine when the PAGE ERASE cycle is complete. The PAGE ERASE instruction will erase all bits (FFh) inside the given page. A Write Enable (WREN) instruction must be given prior to attempting a PAGE ERASE. This is done by setting CS low and then clocking out the proper instruction into the 25LC512. After all eight bits of the instruction are transmitted, the CS must be brought high to set the write enable latch. If a PAGE ERASE instruction is given to an address that has been protected by the Block Protect bits (BP0, BP1) then the sequence will be aborted and no erase will occur. The PAGE ERASE instruction is entered by driving CS low, followed by the instruction code (Figure 2-8) and two address bytes. Any address inside the page to be erased is a valid address. FIGURE 2-8: PAGE ERASE SEQUENCE CS 0 1 2 3 4 5 6 7 8 9 10 11 21 22 23 SCK Instruction SI 0 1 0 0 0 16-bit Address 0 1 0 15 14 13 12 2 1 0 High-Impedance SO DS20005265A-page 14 2014 Microchip Technology Inc. 25LC512 2.9 SECTOR ERASE CS must then be driven high after the last bit of the address or the SECTOR ERASE will not execute. Once the CS is driven high the self-timed SECTOR ERASE cycle is started. The WIP bit in the STATUS register can be read to determine when the SECTOR ERASE cycle is complete. The SECTOR ERASE instruction will erase all bits (FFh) inside the given sector. A Write Enable (WREN) instruction must be given prior to attempting a SECTOR ERASE. This is done by setting CS low and then clocking out the proper instruction into the 25LC512. After all eight bits of the instruction are transmitted, the CS must be brought high to set the write enable latch. If a SECTOR ERASE instruction is given to an address that has been protected by the Block Protect bits (BP0, BP1) then the sequence will be aborted and no erase will occur. The SECTOR ERASE instruction is entered by driving CS low, followed by the instruction code (Figure 2-9) and two address bytes. Any address inside the sector to be erased is a valid address. FIGURE 2-9: See Table 2-3 for Sector Addressing. SECTOR ERASE SEQUENCE CS 0 1 2 3 4 5 6 7 8 9 10 11 21 22 23 SCK Instruction SI 1 1 0 1 1 16-bit Address 0 0 0 15 14 13 12 2 1 0 High-Impedance SO 2014 Microchip Technology Inc. DS20005265A-page 15 25LC512 2.10 CHIP ERASE The CS pin must be driven high after the eighth bit of the instruction code has been given or the CHIP ERASE instruction will not be executed. Once the CS pin is driven high the self-timed CHIP ERASE instruction begins. While the device is executing the CHIP ERASE instruction the WIP bit in the STATUS register can be read to determine when the CHIP ERASE instruction is complete. The CHIP ERASE instruction will erase all bits (FFh) in the array. A Write Enable (WREN) instruction must be given prior to executing a CHIP ERASE. This is done by setting CS low and then clocking out the proper instruction into the 25LC512. After all eight bits of the instruction are transmitted, the CS must be brought high to set the write enable latch. The CHIP ERASE instruction is entered by driving the CS low, followed by the instruction code (Figure 2-10) onto the SI line. FIGURE 2-10: The CHIP ERASE instruction is ignored if either of the Block Protect bits (BP0, BP1) are not 0, meaning ¼, ½, or all of the array is protected. CHIP ERASE SEQUENCE CS 0 1 2 3 4 5 6 7 SCK SI 1 1 0 0 0 1 1 1 High-Impedance SO DS20005265A-page 16 2014 Microchip Technology Inc. 25LC512 2.11 DEEP POWER-DOWN MODE Deep Power-Down mode of the 25LC512 is its lowest power consumption state. The device will not respond to any of the Read or Write commands while in Deep Power-Down mode and, therefore, it can be used as an additional software write protection feature. All instructions given during Deep Power-Down mode are ignored except the Read Electronic Signature command (RDID). The RDID command will release the device from Deep power-down and outputs the electronic signature on the SO pin, and then returns the device to Standby mode after delay (TREL) The Deep Power-Down mode is entered by driving CS low, followed by the instruction code (Figure 2-11) onto the SI line, followed by driving CS high. Deep Power-Down mode automatically releases at device power-down. Once power is restored to the device it will power-up in the Standby mode. If the CS pin is not driven high after the eighth bit of the instruction code has been given, the device will not execute Deep power-down. Once the CS line is driven high there is a delay (TDP) before the current settles to its lowest consumption. FIGURE 2-11: DEEP POWER-DOWN SEQUENCE CS 0 1 2 3 4 5 6 7 SCK SI 1 0 1 1 1 0 0 1 High-Impedance SO 2014 Microchip Technology Inc. DS20005265A-page 17 25LC512 2.12 RELEASE FROM DEEP POWER-DOWN AND READ ELECTRONIC SIGNATURE Once the device has entered Deep Power-Down mode all instructions are ignored except the Release from Deep Power-down and Read Electronic Signature command. This command can also be used when the device is not in Deep power-down to read the electronic signature out on the SO pin unless another command is being executed such as Erase, Program or Write Status Register. FIGURE 2-12: Release from Deep Power-Down mode and Read Electronic Signature is entered by driving CS low, followed by the RDID instruction code (Figure 2-12) and then a dummy address of 16 bits (A15-A0). After the last bit of the dummy address is clocked in, the 8-bit Electronic Signature is clocked out on the SO pin. After the signature has been read out at least once, the sequence can be terminated by driving CS high. After a delay of TREL, the device will then return to Standby mode and will wait to be selected so it can be given new instructions. If additional clock cycles are sent after the electronic signature has been read once, it will continue to output the signature on the SO line until the sequence is terminated. RELEASE FROM DEEP POWER-DOWN AND READ ELECTRONIC SIGNATURE CS TREL 0 1 2 3 4 5 6 7 8 9 10 11 21 22 23 24 25 26 27 28 29 30 31 SCK Instruction SI 1 0 1 0 1 16-bit Address 0 1 15 14 13 12 1 2 1 0 Electronic Signature Out High-Impedance 7 SO 0 6 5 4 3 2 1 0 0 1 0 1 0 0 1 Manufacturer’s ID = 0x29 Driving CS high after the 8-bit RDID command but before the Electronic Signature has been transmitted will still ensure the device will be taken out of Deep Power-Down mode, as shown in Figure 2-13. FIGURE 2-13: RELEASE FROM DEEP POWER-DOWN CS 0 1 1 0 2 3 4 5 6 0 1 7 TREL SCK Instruction SI 1 0 1 1 High-Impedance SO DS20005265A-page 18 2014 Microchip Technology Inc. 25LC512 3.0 PIN DESCRIPTIONS The descriptions of the pins are listed in Table 3-1. TABLE 3-1: PIN FUNCTION TABLE Name Pin Number CS 1 Chip Select Input SO 2 Serial Data Output WP 3 Write-Protect Pin VSS 4 Ground SI 5 Serial Data Input SCK 6 Serial Clock Input HOLD 7 Hold Input VCC 8 Supply Voltage 3.1 Function Chip Select (CS) A low level on this pin selects the device. A high level deselects the device and forces it into Standby mode. However, a programming cycle which is already initiated or in progress will be completed, regardless of the CS input signal. If CS is brought high during a program cycle, the device will go into Standby mode as soon as the programming cycle is complete. When the device is deselected, SO goes to the high-impedance state, allowing multiple parts to share the same SPI bus. A low-to-high transition on CS after a valid write sequence initiates an internal write cycle. After powerup, a low level on CS is required prior to any sequence being initiated. 3.2 Serial Output (SO) The SO pin is used to transfer data out of the 25LC512. During a read cycle, data is shifted out on this pin after the falling edge of the serial clock. 3.3 Write-Protect (WP) This pin is used in conjunction with the WPEN bit in the STATUS register to prohibit writes to the nonvolatile bits in the STATUS register. When WP is low and WPEN is high, writing to the nonvolatile bits in the STATUS register is disabled. All other operations function normally. When WP is high, all functions, including writes to the nonvolatile bits in the STATUS register, operate normally. If the WPEN bit is set, WP low during a STATUS register write sequence will disable writing to the STATUS register. If an internal write cycle has already begun, WP going low will have no effect on the write. 2014 Microchip Technology Inc. The WP pin function is blocked when the WPEN bit in the STATUS register is low. This allows the user to install the 25LC512 in a system with WP pin grounded and still be able to write to the STATUS register. The WP pin functions will be enabled when the WPEN bit is set high. 3.4 Serial Input (SI) The SI pin is used to transfer data into the device. It receives instructions, addresses and data. Data is latched on the rising edge of the serial clock. 3.5 Serial Clock (SCK) The SCK is used to synchronize the communication between a master and the 25LC512. Instructions, addresses or data present on the SI pin are latched on the rising edge of the clock input, while data on the SO pin is updated after the falling edge of the clock input. 3.6 Hold (HOLD) The HOLD pin is used to suspend transmission to the 25LC512 while in the middle of a serial sequence without having to re-transmit the entire sequence over again. It must be held high any time this function is not being used. Once the device is selected and a serial sequence is underway, the HOLD pin may be pulled low to pause further serial communication without resetting the serial sequence. The HOLD pin should be brought low while SCK is low, otherwise the HOLD function will not be invoked until the next SCK high-to-low transition. The 25LC512 must remain selected during this sequence. The SI and SCK levels are “don’t cares” during the time the device is paused and any transitions on these pins will be ignored. To resume serial communication, HOLD should be brought high while the SCK pin is low, otherwise, serial communication will not be resumed until the next SCK high-to-low transition. The SO line will tri-state immediately upon a high-tolow transition of the HOLD pin, and will begin outputting again immediately upon a subsequent low-to-high transition of the HOLD pin, independent of the state of SCK. DS20005265A-page 19 25LC512 4.0 PACKAGING INFORMATION 4.1 Package Marking Information 8-Lead SOIC Example: XXXXXXXT XXXXYYWW NNN 25LC512M SN e3 1349 1L7 Legend: XX...X T Y YY WW NNN e3 Note: Note: DS20005265A-page 20 Part number or part number code Temperature (M) Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week ‘01’) Alphanumeric traceability code (2 characters for small packages) JEDEC® designator for Matte Tin (Sn) For very small packages with no room for the JEDEC designator e3 , the marking will only appear on the outer carton or reel label. In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. 2014 Microchip Technology Inc. 25LC512 /HDG3ODVWLF6PDOO2XWOLQH61±1DUURZPP%RG\>62,&@ 1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW KWWSZZZPLFURFKLSFRPSDFNDJLQJ D e N E E1 NOTE 1 1 2 3 α h b h A2 A c φ L A1 L1 8QLWV 'LPHQVLRQ/LPLWV 1XPEHURI3LQV β 0,//,0(7(56 0,1 1 120 0$; 3LWFK H 2YHUDOO+HLJKW $ ± %6& ± 0ROGHG3DFNDJH7KLFNQHVV $ ± ± 6WDQGRII $ ± 2YHUDOO:LGWK ( 0ROGHG3DFNDJH:LGWK ( %6& 2YHUDOO/HQJWK ' %6& %6& &KDPIHURSWLRQDO K ± )RRW/HQJWK / ± )RRWSULQW / 5() )RRW$QJOH ± /HDG7KLFNQHVV F ± /HDG:LGWK E ± 0ROG'UDIW$QJOH7RS ± 0ROG'UDIW$QJOH%RWWRP ± 1RWHV 3LQYLVXDOLQGH[IHDWXUHPD\YDU\EXWPXVWEHORFDWHGZLWKLQWKHKDWFKHGDUHD 6LJQLILFDQW&KDUDFWHULVWLF 'LPHQVLRQV'DQG(GRQRWLQFOXGHPROGIODVKRUSURWUXVLRQV0ROGIODVKRUSURWUXVLRQVVKDOOQRWH[FHHGPPSHUVLGH 'LPHQVLRQLQJDQGWROHUDQFLQJSHU$60(<0 %6& %DVLF'LPHQVLRQ7KHRUHWLFDOO\H[DFWYDOXHVKRZQZLWKRXWWROHUDQFHV 5() 5HIHUHQFH'LPHQVLRQXVXDOO\ZLWKRXWWROHUDQFHIRULQIRUPDWLRQSXUSRVHVRQO\ 0LFURFKLS 7HFKQRORJ\ 'UDZLQJ &% 2014 Microchip Technology Inc. DS20005265A-page 21 25LC512 /HDG3ODVWLF6PDOO2XWOLQH61±1DUURZPP%RG\>62,&@ 1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW KWWSZZZPLFURFKLSFRPSDFNDJLQJ DS20005265A-page 22 2014 Microchip Technology Inc. 25LC512 APPENDIX A: REVISION HISTORY Revision A (01/2014) Original release. 2014 Microchip Technology Inc. DS20005265A-page 23 25LC512 NOTES: DS20005265A-page 24 2014 Microchip Technology Inc. 25LC512 THE MICROCHIP WEB SITE CUSTOMER SUPPORT Microchip provides online support via our WWW site at www.microchip.com. This web site is used as a means to make files and information easily available to customers. Accessible by using your favorite Internet browser, the web site contains the following information: Users of Microchip products can receive assistance through several channels: • Product Support – Data sheets and errata, application notes and sample programs, design resources, user’s guides and hardware support documents, latest software releases and archived software • General Technical Support – Frequently Asked Questions (FAQ), technical support requests, online discussion groups, Microchip consultant program member listing • Business of Microchip – Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives • • • • Distributor or Representative Local Sales Office Field Application Engineer (FAE) Technical Support Customers should contact their distributor, representative or Field Application Engineer (FAE) for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in the back of this document. Technical support is available through the web site at: http://microchip.com/support CUSTOMER CHANGE NOTIFICATION SERVICE Microchip’s customer notification service helps keep customers current on Microchip products. Subscribers will receive e-mail notification whenever there are changes, updates, revisions or errata related to a specified product family or development tool of interest. To register, access the Microchip web site at www.microchip.com. Under “Support”, click on “Customer Change Notification” and follow the registration instructions. 2014 Microchip Technology Inc. DS20005265A-page 25 25LC512 NOTES: DS20005265A-page 26 2014 Microchip Technology Inc. 25LC512 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. X Device Tape & Reel – X /XX Temp Range Package Device: 25LC512 512 Kbit, 2.5V, 128-Byte Page SPI Serial EEPROM Tape & Reel: Blank = T = Standard packaging (tube) Tape & Reel Temperature Range: M = -55C to +125C Package: SN = Plastic SOIC (3.90 mm body), 8-lead 2014 Microchip Technology Inc. Examples: a) 25LC512-M/SN = 512 Kbit, 2.5V Serial EEPROM, Extended temp., SOIC package b) 25LC512T-M/SN = 512 Kbit, 2.5V Serial EEPROM, Extended temp., Tape and Reel, SOIC package DS20005265A-page 27 25LC512 NOTES: DS20005265A-page 28 2014 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, FlashFlex, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, PIC32 logo, rfPIC, SST, SST Logo, SuperFlash and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MTP, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries. Analog-for-the-Digital Age, Application Maestro, BodyCom, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, Mindi, MiWi, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE, rfLAB, Select Mode, SQI, Serial Quad I/O, Total Endurance, TSHARC, UniWinDriver, WiperLock, ZENA and Z-Scale are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. GestIC and ULPP are registered trademarks of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries. All other trademarks mentioned herein are property of their respective companies. © 2014, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. ISBN: 9781620778586 QUALITY MANAGEMENT SYSTEM CERTIFIED BY DNV == ISO/TS 16949 == 2014 Microchip Technology Inc. Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. DS20005265A-page 29 Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4123 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Austin, TX Tel: 512-257-3370 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Novi, MI Tel: 248-848-4000 Houston, TX Tel: 281-894-5983 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 New York, NY Tel: 631-435-6000 San Jose, CA Tel: 408-735-9110 Canada - Toronto Tel: 905-673-0699 Fax: 905-673-6509 DS20005265A-page 30 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8569-7000 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 China - Chongqing Tel: 86-23-8980-9588 Fax: 86-23-8980-9500 China - Hangzhou Tel: 86-571-2819-3187 Fax: 86-571-2819-3189 China - Hong Kong SAR Tel: 852-2943-5100 Fax: 852-2401-3431 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 China - Shenzhen Tel: 86-755-8864-2200 Fax: 86-755-8203-1760 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 India - Pune Tel: 91-20-3019-1500 Japan - Osaka Tel: 81-6-6152-7160 Fax: 81-6-6152-9310 Japan - Tokyo Tel: 81-3-6880- 3770 Fax: 81-3-6880-3771 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Germany - Dusseldorf Tel: 49-2129-3766400 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Germany - Pforzheim Tel: 49-7231-424750 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Italy - Venice Tel: 39-049-7625286 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 Poland - Warsaw Tel: 48-22-3325737 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan - Hsin Chu Tel: 886-3-5778-366 Fax: 886-3-5770-955 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 Sweden - Stockholm Tel: 46-8-5090-4654 UK - Wokingham Tel: 44-118-921-5800 Fax: 44-118-921-5820 Taiwan - Kaohsiung Tel: 886-7-213-7830 Taiwan - Taipei Tel: 886-2-2508-8600 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 10/28/13 2014 Microchip Technology Inc.