BRD4505B Reference Manual

Reference Manual
BRD4505B (Rev. A00)
The EZR32WG family of Wireless MCUs deliver a high performance, low energy wireless solution integrated into a small form factor package. By combining a high performance sub-GHz RF transceiver
with an energy efficient 32-bit MCU, the family provides designers the ultimate in flexibility with a family of pin-compatible devices that scale from 64/128/256 kB of flash and support Silicon Labs EZRadio
or EZRadioPRO transceivers. The ultra-low power operating modes and fast wake-up times of the
Silicon Labs energy friendly 32-bit MCUs, combined with the low transmit and receive power consumption of the sub-GHz radio, result in a solution optimized for battery powered applications.
To develop and/or evaluate the EZR32 Wonder Gecko the EZR32WG Radio Board can
be connected to the Wireless Starter Kit Mainboard to get access to display, buttons and
additional features from Expansion Boards.
RADIO BOARD FEATURES
• Wireless MCU: EZR32WG330F256R63G
• CPU core: ARM Cortex-M4
• Flash memory: 256 kB
• RAM: 32 kB
• Sub-GHz transceiver integrated in the
Wireless MCU: EZRadioPRO
• Operation frequency: 490 MHz
• Transmit power: 20 dBm
• Single antenna connector both for transmit
and receive
• Crystals for LFXO and HFXO: 32.768kHz
and 48 MHz.
• Crystal for RF: 30 MHz
• Backup Power Domain Capacitor
• Full speed USB 2.0 (12 Mbps)
silabs.com | Smart. Connected. Energy-friendly.
Rev. 1.10
BRD4505B (Rev. A00)
Table of Contents
1. Radio Board Connector Pin Associations. . . . . . . . . . . . . . . . . . . . . 1
2. EZR32WG330 System-on-Chip Summary . . . . . . . . . . . . . . . . . . . . . 2
2.1 EZR32 Wireless MCU .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 2
2.2 EZRadioPRO RF Transceiver
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 2
2.3 Communcation Between the MCU and the Radio .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 2
3. EZR32WG Radio Board block description
3.1 USB .
.
.
.
.
. . . . . . . . . . . . . . . . . . . . 4
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 4
3.2 RF Crystal Oscillator
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 4
3.3 LF Crystal Oscillator (LFXO) .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 4
3.4 HF Crystal Oscillator (HFXO) .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 4
3.5 Backup Power Domain Capacitor .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 4
3.6 RF Matching Network .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 5
3.7 SMA connector
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 5
3.8 Radio Board Connectors .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 5
.
.
.
4. RF section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.1 Matching network.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 6
5. Mechanical details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6. RF performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6.1 Measurement setup .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 9
6.2 Conducted Power Measurements .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 9
6.3 Radiated Power Measurements .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.10
.
7. Document Revision History . . . . . . . . . . . . . . . . . . . . . . . . . 12
8. Errata
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Table of Contents
ii
BRD4505B (Rev. A00)
Radio Board Connector Pin Associations
1. Radio Board Connector Pin Associations
The board-to-board connector scheme allows access to all EZR32WG GPIO pins as well as the nRESET signal. The figure below
shows the pin mapping on the connector to the radio pins, and their function on the Wireless Starter Kit Mainboard. For more information on the functions of the available pin functions, we refer you to the EZR32WG330 Datasheeet.
Figure 1.1. EZR32WG Radio Board Radio Board Connector pin mapping
silabs.com | Smart. Connected. Energy-friendly.
Rev. 1.10 | 1
BRD4505B (Rev. A00)
EZR32WG330 System-on-Chip Summary
2. EZR32WG330 System-on-Chip Summary
The EEZR32WG330 Wireless MCU is a single-chip solution that combines an Wonder Gecko family MCU solution with an integrated
EZRadio or EZRadioPRO sub-GHz RF transceiver. These products are designed to address the specific requirements of low-power
embedded systems requiring an RF bidirectional communication link.
The block diagram of the EZR32WG330 is shown in the figure below.
Figure 2.1. EZR32WG330 block diagram
For a complete feature set and in-depth information on the modules, the reader is referred to the EZR32WG330 Reference Manual
2.1 EZR32 Wireless MCU
The EZR32 Wireless MCU are the world’s most energy friendly Wireless Microcontroller. With a unique combination of the powerful 32bit ARM Cortex-M4, innovative low energy techniques, short wake-up time from energy saving modes, and a wide selection of peripherals, the EZR32 WG is well suited for any battery operated application as well as other systems requiring high performance and lowenergy consumption.
2.2 EZRadioPRO RF Transceiver
The EZR32WG family of devices is built using high-performance, low-current EZRadio and EZRadioPRO RF transceivers covering the
sub-GHz frequency bands from 142 to 1050 MHz. These devices offer outstanding sensitivity of up to –133 dBm (using EZRadioPRO)
while achieving extremely low active and standby current consumption. The EZR32WG devices using the transceiver offer frequency
coverage in all major bands and include optimal phase noise, blocking, and selectivity performance for narrow band and licensed band
applications, such as FCC Part 90 and 169 MHz wireless Mbus. The 69 dB adjacent channel selectivity with 12.5 kHz channel spacing
ensures robust receive operation in harsh RF conditions, which is particularly important for narrow band operation. The active mode TX
current consumption of 18 mA at +10 dBm and RX current of 10 mA coupled with extremely low standby current and fast wake times is
optimized for extended battery life in the most demanding applications. The EZR32WG devices can achieve up to +27 dBm output power with built-in ramping control of a low-cost external FET. The devices can meet worldwide regulatory standards: FCC, ETSI, and
ARIB. All devices are designed to be compliant with 802.15.4g and WMbus smart metering standards. The devices are highly flexible
and can be programmed and configured via Simplicity Studio, available at www.silabs.com.
For a complete feature set and in-depth information on the modules, the reader is referred to the Data Sheet "Si4463-61-60-C HighPerformance, Low-Current Transceiver".
2.3 Communcation Between the MCU and the Radio
Communication between the radio and MCU are done over USART, PRS and IRQ, which requires the pins to be configured in the following way:
silabs.com | Smart. Connected. Energy-friendly.
Rev. 1.10 | 2
BRD4505B (Rev. A00)
EZR32WG330 System-on-Chip Summary
Table 2.1. Radio MCU Communication Configuration
pin
Radio Assignment
pin function assignment
PE8
SDN
GPIO Output
PE9
nSEL
Bit-Banged SPI.CS (GPIO Output)
PE10
SDI
US0_TX #0
PE11
SDO
US0_RX #0
PE12
SCLK
US0_CLK #0
PE13
nIRQ
GPIO_EM4WU5 (GPIO Input with IRQ enabled)
PE14
GPIO1
PRS Input
PA15
GPIO0
PRS Input
silabs.com | Smart. Connected. Energy-friendly.
Rev. 1.10 | 3
BRD4505B (Rev. A00)
EZR32WG Radio Board block description
3. EZR32WG Radio Board block description
The block diagram of the EZR32WG Radio Board is shown in the figure below.
USB_VBUS (5 V)
EZRWG330
USB Micro-B
USB_D+/DConnector
USB Regulator Output (3.3 V)
to WSTK Motherboard
USB_VREGO
Radio Board Connectors
Power Supply (3.3 V)
from WSTK Motherboard
VMCU
PA
PB
PC
PD
PE
PF
Power
Domain
Backup
Capacitor
MCU
I/O
Ports
VRF
LF Crystal
(32.768 kHz)
MCU
USB_VBUS
USB_VREGI
HF Crystal
(48 MHz)
RF Crystal
(30 MHz)
RADIO
XIN/XOUT
TX_20
RXN/RXP
Switched RF
Matching
Network
SMA
Connector
GPIO2/3
Board
Identification
RF Switch Control
Figure 3.1. EZR32WG Radio Board block diagram
3.1 USB
The EZR32WG Radio Board incorporates a micro USB connector (P/N: ZX62-B-5PA(11)). The 3.3V USB regulator output is are routed
back to the WSTK through the Radio Board Connector so the Radio Board can supply power to the Wireless Starter Kit Mainboard.
For additional information on EZR32WG USB, refer to the EZR32WG330 Data Sheet.
3.2 RF Crystal Oscillator
The BRD4505B (Rev. A00) Radio Board has a 30 MHz crystal mounted (P/N: NX2016SA 30 MHz EXS00A-CS06568). For more details
on crystal or TCXO selection for the RF part of the EZR32 devices refer to "AN785: Crystal Selection Guide for the Si4x6x RF ICs".
3.3 LF Crystal Oscillator (LFXO)
The BRD4505B (Rev. A00) Radio Board has a 32.768kHz crystal mounted (P/N: MS3V-T1R, 32768Hz, 12.5pF, +/- 20ppm). For safe
startup two 22 pF capacitors are also connected to the LFXTAL_N and LFXTAL_H pins. For details regarding the crystal configuration,
the reader is referred to Application Note "AN0016: EFM32 Oscillator Design Consideration".
3.4 HF Crystal Oscillator (HFXO)
The BRD4505B (Rev. A00) Radio Board has a 48 MHz crystal mounted (P/N: ABM11-48.000MHZ-D2X-T3). For safe startup two 10 pF
capacitors are also connected to the HFXTAL_N and HFXTAL_H pins. For details regarding the crystal configuration, the reader is referred to Application Note "AN0016: EFM32 Oscillator Design Consideration".
3.5 Backup Power Domain Capacitor
The BRD4505B (Rev. A00) Radio Board has a 30 mF super capacitor mounted (P/N: PAS311HR-VA6R), connected to the PD8 port of
the EZR32WG.
For details regarding the Backup Power Domain, the reader is referred to the EZR32WG330 Data Sheet.
silabs.com | Smart. Connected. Energy-friendly.
Rev. 1.10 | 4
BRD4505B (Rev. A00)
EZR32WG Radio Board block description
3.6 RF Matching Network
The BRD4505B (Rev. A00) Radio Board includes a Class E type matching network with Switched RF TX and RX sides are connected
together with an additional RF switch, to be able to use one antenna both for transmitting and receiveing. The component values were
optimized for the 490 MHz band RF performace and current consumption with 20 dBm output power.
For more details on the matching network used on the BRD4505B (Rev. A00) see Chapter 4.1 Matching network
3.7 SMA connector
To be able to perform conducted measurements or mount external antenna for radiated measurements, range tests etc., Silicon Labs
added an SMA connector (P/N: 5-1814832-1) to the Radio Board. The connector allows an external 50 Ohm cable or antenna to be
connected during design verification or testing.
3.8 Radio Board Connectors
Two dual-row, 0.05” pitch polarized connectors (P/N: SFC-120-T2-L-D-A-K-TR) make up the EZR32WG Radio Board interface to the
Wireless Starter Kit Mainboard.
For more information on the pin mapping between the EZR32WG330F256R63G and the Radio Board Connector refer to Chapter
1. Radio Board Connector Pin Associations.
silabs.com | Smart. Connected. Energy-friendly.
Rev. 1.10 | 5
BRD4505B (Rev. A00)
RF section
4. RF section
The BRD4505B (Rev. A00) Radio Board includes a Class E type TX matching network with the targeted output power of 20 dBm at 490
MHz.
The main advantage of the Class E matching types is their very high efficiency. They are proposed for applications where the current
consumption is most critical, e.g., the typical total EZRadioPRO chip current with Class E type matching is ~75-90 mA at ~20 dBm
power levels (using the 20 dBm PA output and assuming 3.3 V Vdd).
The main disadvantage of the Class E type matches is the high Vdd dependency (the power variation is proportional to the square of
the Vdd change: i.e. the decrease in power can be ~6 dB in the 1.8–3.8 V range) and the inaccurate nonlinear power steps. Also their
current consumption and the peak voltage on the TX pin are sensitive to the termination impedance variation, and they usually require
slightly higher order filtering and thus higher bill of materials cost.
The matching network is constructed with a so-called Switched RF configuration where the TX and RX sides are connected together
with an additional RF switch, to be able to use one antenna both for transmitting and receiveing. Careful design procedure was followed
to ensure that the RX input circuitry does not load down the TX output path while in TX mode and that the TX output circuitry does not
degrade receive performance while in RX mode.
For detailed explanation of the Class E type TX matching and the Switched RF configuration matching procedure the reader is referred
to "AN648: Si4063/Si4463/64/68 TX Matching". For detailed description of the RX matching the reader is referred to "AN643: Si446x/
Si4362 RX LNA Matching".
4.1 Matching network
The matching network structure used on the BRD4505B (Rev. A00) Radio Board is shown in the figure below.
GND
U1B
EZR32xx
7
9
VDD_RF
LNA Balun
CR1
LR2
RXP
RADIO_RF_GPIO2
2
CC1
VDD_RF
LR1
RXN
RF Switch
uPG2214TB
3
P1
3
2
1
VRF
GND
62
61
OUT2
GND
OUT1
XIN
RF_IN
VC1
4
CC2
2
3
LM3
5
1
4
5
6
CM3
GND
CM4
TP1
RF_TEST_POINT
GND
SMA
GND
GND
XOUT
TX_13
TXRAMP
VC2
U2
LC
TX_20
8
Antenna
Connector
RADIO_RF_GPIO3
CR2
4
L0
C0
LM
LM2
CC3
Filter2
5
LM1
PA Matching
CM2
GND
GND
Filter1
Figure 4.1. RF section of the schematic of the EZR32 Wonder Gecko Radio Board (BRD4505B (Rev. A00))
The matching network has a so-called Switched RF configuration where the TX and RX sides are connected together, without an additional RF switch, to be able to use one antenna both for transmitting and receiving.
For detailed explanation of the TX matching process, see "AN648: Si4063/Si4463/64/68 TX Matching". Due to the Switched RF configuration of the matching, the RX matching should also taken into account during the TX matching procedure. The above Application
Note contains component values and a shorter description for the RX matching as well. For detailed description of the RX matching
refer to "AN643: Si446x/Si4362 RX LNA Matching".
The component values were optimized for the 490 MHz band RF performace and current consumption with 20 dBm output power. The
resulting component values with part numbers are listed in the table below.
silabs.com | Smart. Connected. Energy-friendly.
Rev. 1.10 | 6
BRD4505B (Rev. A00)
RF section
Table 4.1. Bill of Materials for the BRD4505B (Rev. A00) RF matching network
Component name
Value
Part Number
C0
3.9 pF
GRM1555C1H3R9B
CM2
5.6 pF
GRM1555C1H5R6C
CM3
9.1 pF
GRM1555C1H9R1D
CM4
9.1 pF
GRM1555C1H9R1D
CR1
3.9 pF
GRM1555C1H3R9C
CR2
2.2 pF
GRM1555C1H2R2B
CC1
150 pF
GRM1555C1H151J
CC2
150 pF
GRM1555C1H151J
CC3
150 pF
GRM1555C1H151J
L0
24 nH
0402HP-24NXJL
LC
220 nH
0402HPH-R22XJL
LM
27 nH
0402HP-27NXJL
LM1
24 nH
0402HP-24NXJL
LM2
27 nH
0402HP-27NXJL
LM3
15 nH
0402HP-15NXJL
LR1
51 nH
0402HP-51NXJL
LR2
47 nH
0402HP-47NXJL
The Application Note "AN648: Si4063/Si4463/64/68 TX Matching" contains component values for reference matching networks which
were developed for the EZRadioPRO Pico Boards. For the WSTK radio boards some fine-tuning of the component values may be necessary due to different parasitic effects (bonding wire, layout etc.). For optimized RF performance the component values listed in the
table above may differ from the ones listed in the referred Application Note.
For the reader’s specific application and board layout the adjustment of the final matching values might be necessary. The above component values should be used as starting points and the values modified slightly to zero-in on the best filter response and impedance
match to 50 ohm. To minimize the differences due to different layout parasitics Silicon Labs recommends copying the layout of the RF
section of the radio board as is. If that is not possible, refer to "AN629: Si4460/61/63/64 RF ICs Layout Design Guide" for layout design
recommendations.
silabs.com | Smart. Connected. Energy-friendly.
Rev. 1.10 | 7
BRD4505B (Rev. A00)
Mechanical details
5. Mechanical details
The EZR32 Wonder Gecko Radio Board (BRD4505B (Rev. A00)) is illustrated in the figures below.
0.81 mm
2.7 mm
USB
Connector
7.5 mm
Power
Domain
Backup
Capacitor
HFXTAL
Frame of the
Optional
Shielding Can
LFXTAL
30 mm
23 mm
Board
Identification
RF
Matching
and
Filtering
EZR32xx
RFXTAL
SMA Connector
RF Switch
43 mm
Figure 5.1. BRD4505B (Rev. A00) top view
5 mm
24 mm
28.6 mm
27.3 mm
15 mm
Interface
Connector
Interface
Connector
Figure 5.2. BRD4505B (Rev. A00) bottom view
silabs.com | Smart. Connected. Energy-friendly.
Rev. 1.10 | 8
BRD4505B (Rev. A00)
RF performance
6. RF performance
6.1 Measurement setup
The EZR32 Wonder Gecko Radio Board (BRD4505B (Rev. A00))was attached to a Wireless Starter Kit Mainboard (BRD4001 (Rev.
A02)) and its transceiver was operated in continuous carrier transmission mode. The output power of the radio was set to 20 dBm
(DDAC = 7Fh).
6.2 Conducted Power Measurements
In case of the conducted measurements the output power was measured by connecting the EZR32WG Radio Board directly to a Spectrum Analyzer (P/N: MS2692A) through its on-board SMA connector. At 20 dBm output power and 3.3 V supply voltage the measured
typical current consumption of the RF section of the board is 75 mA.
A typical output spectrum up to 10 GHz is shown in the figure below.
Figure 6.1. Typical output spectrum of the BRD4505B (Rev. A00) Radio Board; with DDAC=7Fh at Vdd=3.3 V
Note: In practice comercially available whip antennas usually have ~0-2 dB gain at the fundamental and < 0 dB gain at the harmonic
frequencies so if the conducted levels are compliant with the emission limits with small margin it is likely that the margin on the harmonics radiated by an external whip antenna will be higher. Unfortunately in most cases, the PCB radiation (from traces or and/or components) is stronger so using shielding, applying larger duty cycle correction (if allowed) or reductionof the fundamental power could be
necessary.
silabs.com | Smart. Connected. Energy-friendly.
Rev. 1.10 | 9
BRD4505B (Rev. A00)
RF performance
6.3 Radiated Power Measurements
For radiated measurements an external whip antenna (P/N: HT-A-450-6100) was used. The power supply for the board were two AA
batteries (3 V). The batteries were connected to the Wireless Starter Kit Mainboard through its External Power Supply connector with
minimal wire length to minimize the wire radiation.
The DUT was rotated in 360 degree with horizontal and vertical reference antenna polarizations in the XY, XZ and YZ cuts. The measurement axes are as shown in the figure below.
Figure 6.2. DUT: BRD4505B (Rev. A00) Radio Board with Wireless Starter Kit Mainboard
The measured radiated powers are shown in the table below.
Table 6.1. Results of the radiated power measurements
490 MHz
Measured maximums of the radiated power in EIRP [dBm]
XY
XZ
AMR limit in
EIRP [dBm]
YZ
H
V
H
V
H
V
Fundamental
+18.7
+20.2
+21.8
+16.2
+22.4
+14.9
+19.1
2nd harmonic
-52.7
-48.0
-51.5
-51.4
-51.9
-53.2
-33.9
3rd harmonic
-46.3
-56.0
-45.8
-80.9
-48.5
-48.0
-27.9
4th harmonic
-59.0
-52.8
-57.1
-55.8
-56.8
-54.3
-27.9
5th harmonic
-54.6
-56.1
-52.4
-54.6
-57.9
-53.4
-27.9
6th harmonic
-59.1
-57.7
-58.9
-55.9
-53.3
-59.3
-27.9
7th harmonic
-57.0
-54.2
-54.5
-56.4
-55.7
-53.6
-27.9
8th harmonic
-58.9
-60.4
-57.3
-60.2
-57.8
-58.5
-27.9
silabs.com | Smart. Connected. Energy-friendly.
Rev. 1.10 | 10
BRD4505B (Rev. A00)
RF performance
490 MHz
Measured maximums of the radiated power in EIRP [dBm]
XY
XZ
AMR limit in
EIRP [dBm]
YZ
H
V
H
V
H
V
9th harmonic
-57.6
-55.6
-55.9
-58.3
-55.9
-55.7
-27.9
10th harmonic
-55.4
-54.3
-51.1
-54.3
-54.8
-54.3
-27.9
Note: * Signal level is below the Spectrum Analyzer noise floor.
One may notice that the radiated harmonic levels are higher compared to the levels expected based on the conducted measurement.
Investigations showed that this increase is due to the PCB radiations (components and PCB traces).
Note: The radiated measurement results presented in this document were recorded in an unlicensed antenna chamber. Also the radiated power levels may change depending on the actual application (PCB size, used antenna etc.) therefore the absolute levels and
margins of the final application is recommended to be verified in a licensed EMC testhouse!
silabs.com | Smart. Connected. Energy-friendly.
Rev. 1.10 | 11
BRD4505B (Rev. A00)
Document Revision History
7. Document Revision History
Table 7.1. Document Revision History
Revision Number
Effective Date
Change Description
1.10
19.03.2015
Radio Board errata added.
1.00
23.02.2015
Major content update.
0.10
04.02.2015
Initial document version.
silabs.com | Smart. Connected. Energy-friendly.
Rev. 1.10 | 12
BRD4505B (Rev. A00)
Errata
8. Errata
Table 8.1. BRD4505B Radio Board Errata
Radio Board Revision
Problem
Description
A00
USB functionality broken. In this revision USB_VREGI and USB_VREGO pins have been swapped. This
means that USB does not work on this revision of the BRD4505B radio board. If
you require USB functionality, please contact support for a replacement.
Missing MCU peripherals Due to EZR32WG330F256R63G chip errata, UART peripherals are not available. UART functionality on USART peripherals remain unaffected.
silabs.com | Smart. Connected. Energy-friendly.
Rev. 1.10 | 13
Simpilcity Studio
One-click access to MCU tools,
documentation, software, source
code libraries & more. Available
for Windows, Mac and Linux!
www.silabs.com/simplicity
MCU Portfolio
www.silabs.com/mcu
SW/HW
www.silabs.com/simplicity
Quality
www.silabs.com/quality
Support and Community
community.silabs.com
Disclaimer
Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers
using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific
device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories
reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy
or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply
or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products must not be used within any Life Support System without the specific
written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected
to result in significant personal injury or death. Silicon Laboratories products are generally not intended for military applications. Silicon Laboratories products shall under no
circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons.
Trademark Information
Silicon Laboratories Inc., Silicon Laboratories, Silicon Labs, SiLabs and the Silicon Labs logo, CMEMS®, EFM, EFM32, EFR, Energy Micro, Energy Micro logo and combinations
thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZMac®, EZRadio®, EZRadioPRO®, DSPLL®, ISOmodem ®, Precision32®, ProSLIC®, SiPHY®,
USBXpress® and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of
ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders.
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
USA
http://www.silabs.com