smdalc

05074
SMDA03LC - SMDA24LCC
Only One Name Means ProTek’Tion™
500 WATT MULTI-LINE LOW CAPACITANCE TVS ARRAY
Description
The SMDAxxLC and SMDAxxLCC Series are low capacitance multi-line transient voltage suppressor arrays that provides
board level protection for standard TTL and MOS bus line applications against the damaging effects of ESD, tertiary
lightning and switching transients.
The SMDAxxLC/LCC Series has a peak pulse power rating of 500 Watts for an 8/20µs waveshape. This device series
meets the IEC 61000-4-2, IEC 61000-4-4 and IEC 61000-4-5 requirements.
SO-8 package
Features
applications
• Compatible with IEC 61000-4-2 (ESD): Air - 15kV, Contact - 8kV
• Compatible with IEC 61000-4-4 (EFT): 40A - 5/50ns
• Compatible with IEC 61000-4-5 (Surge): 12A, 8/20µs - Level 1(LineGnd) & Level 2(Line-Line)
• 500 Watts Peak Pulse Power per Line (tp = 8/20µs)
• Unidirectional and Bidirectional Configurations
• Available in Multiple Voltages Ranging from 3V to 24V
• Protects up to Four Lines
• Low Capacitance: 15pF
• RoHS Compliant
• REACH Compliant
• Computer Interface Protection
• Ethernet - 10/100/1000 Base T
• Test and Measurement Equipment
• Industrial Control - Low Voltage Sensors
Mechanical characteristics
• Molded JEDEC SO-8 Package
• Approximate Weight: 70 milligrams
• Lead-Free Pure-Tin Plating (Annealed)
• Solder Reflow Temperature:
Pure-Tin - Sn, 100: 260-270°C
• 12mm Tape and Reel Per EIA Standard 481
• Flammability Rating UL 94V-0
PIN CONFIGURATIONS
8
7
6
5
8
7
6
5
1
2
3
4
1
2
3
4
UNIDIRECTIONAL
05074.R11 3/13
BIDIRECTIONAL
Page 1
www.protekdevices.com
05074
SMDA03LC - SMDA24LCC
Only One Name Means ProTek’Tion™
typical device characteristics
MAXIMUM RATINGS @ 25°C Unless Otherwise Specified
PARAMETER
SYMBOL
VALUE
UNITS
TL
-55 to 150
°C
Storage Temperature
TSTG
-55 to 150
°C
Peak Pulse Power (tp = 8/20µs) - See Figure 1
PPP
500
Watts
Forward Voltage @ 50mA, 300µs - Square Wave (See Note 1)
VF
1.5
Volts
Operating Temperature
Note
1. Only applies to unidirectional devices.
ELECTRICAL CHARACTERISTICS PER LINE @ 25°C Unless Otherwise Specified
PART
NUMBER
(Note 1)
DEVICE
MARKING
RATED
STAND-OFF
VOLTAGE
minimum
breakdown
voltage
MAXIMUM
CLAMPING
VOLTAGE
(Fig. 2)
MAXIMUM
CLAMPING
VOLTAGE
(Fig. 2)
MAXIMUM
LEAKAGE
CURRENT
MAXIMUM
CAPACITANCE
VWM
VOLTS
@1mA
V(BR)
VOLTS
@I P = 1A
VC
VOLTS
@ 8/20µs
VC @ IPP
VOLTS
@V WM
ID
µA
@0V, 1MHz
C
pF
SMDA03LC
SLA
3.3
4.5
7.0
10.9V @ 43.0A
125
15
SMDA03LCC
SLB
3.3
4.5
7.0
10.9V @ 43.0A
125
15
SMDA05LC
SLC
5.0
6.0
9.8
13.5V @ 42.0A
20
15
SMDA05LCC
SLD
5.0
6.0
9.8
13.5V @ 42.0A
20
15
SMDA08LC
SLE
8.0
8.5
13.4
16.9V @ 34.0A
10
15
SMDA08LCC
SLF
8.0
8.5
13.4
16.9V @ 34.0A
10
15
SMDA12LC
SLG
12.0
13.3
19.0
25.9V @ 27.0A
1
15
SMDA12LCC
SLH
12.0
13.3
19.0
25.9V @ 27.0A
1
15
SMDA15LC
SLJ
15.0
16.7
24.0
30.0V @ 17.0A
1
15
SMDA15LCC
SLK
15.0
16.7
24.0
30.0V @ 17.0A
1
15
SMDA24LC
SLL
24.0
26.7
43.0
49.0V @ 12.0A
1
15
SMDA24LCC
SLM
24.0
26.7
43.0
49.0V @ 12.0A
1
15
Notes
1. Part numbers with a “C” suffix are bidirectional devices, i.e., SMDA03LCC.
05074.R11 3/13
Page 2
www.protekdevices.com
05074
SMDA03LC - SMDA24LCC
Only One Name Means ProTek’Tion™
typical device characteristics
figure 1
peak pulse power vs pulse time
PPP - Peak Pulse Power - Watts
10,000
1,000
500W, 8/20µs Waveform
100
10
0.1
10
100
td - Pulse Duration - µs
Peak Value IPP
80
100
TEST
WAVEFORM
PARAMETERS
tf = 8µs
td = 20µs
e-t
60
40
10,000
figure 3
power derating curve
Peak Pulse Power
8/20µs
80
% Of Rated Power
tf
100
td = t/(IPP/2)
60
40
20
20
0
1,000
figure 2
pulse wave form
120
IPP - Peak Pulse Current - % of IPP
1
0
05074.R11 3/13
5
10
15
t - Time - µs
20
25
30
Page 3
0
Average Power
0
25
50
75 100 125
TA - Ambient Temperature - °C
150
www.protekdevices.com
05074
SMDA03LC - SMDA24LCC
Only One Name Means ProTek’Tion™
typical device characteristics
figure 4
overshoot & clamping voltage for SMDA05LC
20
5 Volts per Division
10
0
-10
-20
ESD Test Pulse - 5 kilovolt, 1/30ns (Waveshape)
05074.R11 3/13
Page 4
www.protekdevices.com
05074
SMDA03LC - SMDA24LCC
Only One Name Means ProTek’Tion™
SPICE MODEL
figure 1
spice model
I/O
I/O
ABD
ABD
LCRD
LCRD
ABD
LCRD
LCRD
Lg
0.8nH
Lg
0.8nH
UNIDIRECTIONAL
BIDIRECTIONAL
ABD - Avalanche Breakdown Diode (TVS)
LCRD: Low Capacitance Rectifier Diode
Lg - Lead Inductance
table 1 - spice parameters
parameter
PART NUMBER
05074.R11 3/13
unit
abd(tvs)
LCRD
BV
V
See Table 2
200
IBV
µA
1
0.01
Cjo
pF
See Table 2
5
IS
A
See Table 2
1E-13
Vj
V
0.6
0.6
M
-
0.33
0.33
N
-
1
1
RS
Ohms
See Table 2
0.31
TT
s
1E-8
1E-9
EG
eV
1.11
1.11
table 2 - abd specific spice parameters
i s (amps)
bv(volts)
cjo(pF)
rs(ohms)
SMDA03LC
4.5
438
1E-11
0.21
SMDA05LC
6.0
284
1E-11
0.14
SMDA08LC
8.5
146
1E-11
0.28
SMDA12LC
13.3
123
1E-13
0.40
SMDA15LC
16.7
102
1E-13
0.52
SMDA24LC
26.7
61
1E-13
1.54
SMDA03LCC
4.5
438
1E-11
0.21
SMDA05LCC
6.0
284
1E-11
0.14
SMDA08LCC
8.5
146
1E-11
0.28
SMDA12LCC
13.3
123
1E-13
0.40
SMDA15LCC
16.7
102
1E-13
0.52
SMDA24LCC
26.7
61
1E-13
1.54
Page 5
www.protekdevices.com
05074
SMDA03LC - SMDA24LCC
Only One Name Means ProTek’Tion™
application information
Line 1
Line 2
Line 3
Line 4
8
7
6
5
1
2
3
4
GND
figure 1 - UNIDIRECTIONAL COMMON-MODE PROTECTION
Circuit connectivity is as follows:
• Line 1 connected to Pin 5.
• Line 2 connected to Pin 6.
• Line 3 connected to Pin 7.
• Line 4 connected to Pin 8.
• Pins 1 - 4 connected to ground.
05074.R11 3/13
Page 6
www.protekdevices.com
05074
SMDA03LC - SMDA24LCC
Only One Name Means ProTek’Tion™
application information
TPIN
TPIP
7
6
5
1
2
3
4
ETHERNET REPEATER
8
TPON
TPOP
figure 2 - BIDIRECTIONAL COMMON-MODE ETHERNET PROTECTION
Circuit connectivity is as follow:
• TPIN connected to Pin 5.
• TPIP connected to Pin 6.
• TPON connected to Pin 1.
• TPOP connected to Pin 2.
• Pins 3, 4, 7 and 8 connected to ground.
circuit board recommendations
Circuit board layout is critical for electromagnetic compatibility protection. The following guidelines are recommended:
• The protection device should be placed near the input terminals or connectors, the device will divert the transient current
immediately before it can be coupled into the nearby traces.
• The path length between the TVS device and the protected line should be minimized.
• All conductive loops including power and ground loops should be minimized.
• The transient current return path to ground should be kept as short as possible to reduce parasitic inductance.
• Ground planes should be used whenever possible. For multilayer PCBs, use ground vias.
05074.R11 3/13
Page 7
www.protekdevices.com
05074
SMDA03LC - SMDA24LCC
Only One Name Means ProTek’Tion™
SO-8 package information
outline dimensions
dim
millimeters
-A-
inches
min
max
min
max
A
4.80
5.00
0.189
0.196
B
3.80
4.00
0.150
0.157
C
1.35
1.75
0.054
0.068
D
0.35
0.49
0.014
0.019
F
0.40
1.25
0.016
0.049
G
1.27 BSC
8
5
-B-
1
G
4
D
0.18
0.25
0.007
0.009
K
0.10
0.25
0.004
0.008
P
5.80
6.20
0.229
0.244
R
0.25
0.50
0.010
0.019
R x 45°
C
0.05 BSC
J
+ 0.010” (0.25mm) M B M
4 PL
P
0° - 10°
-T-
K
+ 0.010” (0.25mm) M T B S A S
8 PL
J
F
NOTES
1.
2.
3.
4.
5.
6.
-T- = Seating plane and datum surface.
Dimensions “A” and “B” are datum.
Dimensions “A” and “B” do not include mold protrusion.
Maximum mold protrusion is 0.015” (0.380mm) per side.
Dimensioning and tolerances per ANSI Y14.5M, 1982.
Dimensions are exclusive of mold flash and metal burrs.
A
pad layout dimensions
dim
millimeters
B
inches
min
max
min
max
A
1.14
1.40
0.045
0.055
B
0.64
0.89
0.025
0.035
C
6.22
-
0.245
-
D
3.94
4.17
0.155
0.165
E
1.02
1.27
0.040
0.050
NOTES
1. Controlling dimension: inches.
05074.R11 3/13
D
C
E
Page 8
www.protekdevices.com
05074
SMDA03LC - SMDA24LCC
Only One Name Means ProTek’Tion™
TAPE AND REEL
P0
D
t
10 Pitches Cumulative
Tolerance on tape ± 0.2
P2
E
F
W
K0
B0
A0
P
User Direction of Feed
specifications
Reel Dia.
Tape
Width
178mm (7”)
12mm
A0
B0
K0
D
E
F
W
P0
P2
P
tmax
6.50 ± 0.10 5.40 ± 0.10 2.00 ± 0.10 1.50 ± 0.10 1.75 ± 0.10 5.50 ± 0.05 12.00 ± 0.30 4.00 ± 0.12 2.00 ± 0.10 4.00 ± 0.10
0.25
Notes
1.
2.
3.
4.
5.
6.
Dimensions are in millimeters.
Surface mount product is taped and reeled in accordance with EIA-481.
Suffix - T7 = 7” Reel - 1,000 pieces per 12mm tape.
Suffix - T13 = 13” Reel - 2,500 pieces per 12mm tape.
Bulk product shipped in tubes of 98 pieces per tube.
Marking on Part - marking code (see page 2), date code, logo and pin one defined by dot on top of package.
Package outline, pad layout and tape specifications per document number 06009.R3 9/10.
ORDERING INFORMATION
base PART NUMBER
(xx = Voltage)
LEADFREE SUFFIX
TAPE SUFFIX
QTY/REEL
REEL SIZE
TUBE qty
SMDAxx/SMDAxxC
-LF
-T7
1,000
7”
98
SMDAxx/SMDAxxC
-LF
-T13
2,500
13”
98
This device is only available in a Lead-Free configuration.
05074.R11 3/13
Page 9
www.protekdevices.com
05074
SMDA03LC - SMDA24LCC
Only One Name Means ProTek’Tion™
company information
COMPANY PROFILE
In business more than 20 years, ProTek Devices™ is a privately-held company located in Tempe, Arizona, that offers a product line of transient voltage suppressors (TVS); avalanche breakdown diodes; steering diode TVS arrays and other surge suppressor component products.
These TVS devices protect electronic systems from the effects of lightning, electrostatic discharge (ESD), nuclear electromagnetic pulses
(NEMP), inductive switching and EMI / RFI. ProTek Devices also offers high performance interface and linear products that include analog
switches; multiplexers; LED drivers; audio control ICs; RF and related high frequency products. The analog devices work in a host of consumer; industrial; automotive and other applications.
CONTACT US
Corporate Headquarters
2929 South Fair Lane
Tempe, Arizona 85282
USA
By Telephone
General: 602-431-8101
Sales: & Marketing: 602-414-5109
Customer Service: 602-414-5114
Product Technical Support: 602-414-5107
By Fax
General: 602-431-2288
By E-mail:
Sales: [email protected]
Customer Service: [email protected]
Technical Support: [email protected]
ProTek Devices (Asia Pacific) Pte. Ltd.
8 Ubi Road 2, #06-19
Zervex
Singapore - 408538
Tel: +65-67488312
Fax: +65-67488313
Web
www.protekdevices.com
COPYRIGHT © ProTek Devices 2000 - This literature is subject to all applicable copyright laws and is not for resale in any manner.
SPECIFICATIONS: ProTek reserves the right to change the electrical and or mechanical characteristics described herein without notice.
DESIGN CHANGES: ProTek reserves the right to discontinue product lines without notice and that the final judgement concerning selection and specifications is the buyer’s and that in furnishing engineering
and technical assistance. ProTek assumes no responsibility with respect to the selection or specifications of such products. ProTek makes no warranty, representation or guarantee regarding the suitability of
its products for any particular purpose, nor does ProTek assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability without limitation special,
consequential or incidental damages.
LIFE SUPPORT POLICY: ProTek Devices products are not authorized for use in life support systems without written consent from the factory.
05074.R11 3/13
Page 10
www.protekdevices.com