SiC417 Datasheet

SiC417
Vishay Siliconix
microBUCKTM SiC417
10-A, 28-V Integrated Buck Regulator with Programmable LDO
DESCRIPTION
FEATURES
The Vishay Siliconix SiC417 is an advanced stand-alone
synchronous buck regulator featuring integrated power
MOSFETs, bootstrap diode, and a programmable LDO in a
space-saving MLPQ 5 x 5 - 32 pin package.
The SiC417 is capable of operating with all ceramic solutions
and switching frequencies up to 1 MHz. The programmable
frequency,
synchronous operation
and
selectable
power-save allow operation at high efficiency across the full
range of load current. The internal programmable LDO may
be used to supply 5 V for the gate drive circuits or it may be
bypassed with an external 5 V for optimum efficiency and
used to drive external N-channel MOSFETs or other loads.
Additional features include cycle-by-cycle current limit,
voltage soft-start, under-voltage protection, programmable
over-current protection, soft shutdown and selectable
power-save. The Vishay Siliconix SiC417 also provides an
enable input and a power good output.
• High efficiency > 92 %
• Internal power MOSFETs:
High-side RDS(ON) = 27 mΩ
Low-side RDS(ON) = 9 mΩ
• Integrated bootstrap diode
• Integrated configurable 150 mA LDO with bypass logic
• Temperature compensated current limit
• Pseudo fixed-frequency adaptive on-time control
• All ceramic solution enabled
• Programmable input UVLO threshold
• Independent enable pin for switcher and LDO
• Selectable ultra-sonic power-save mode
• Internal soft-start and soft-shutdown
• 1 % internal reference voltage
• Power good output and over voltage protection
• Halogen-free according to IEC 61249-2-21 definition
• Compliant to RoHS directive 2002/95/EC
PRODUCT SUMMARY
Input Voltage Range
3 V to 28 V
APPLICATIONS
Output Voltage Range
0.5 V to 5.5 V
Operating Frequency
200 kHz to 1 MHz
Continuous Output Current
Peak Efficiency
•
•
•
•
•
•
10 A
95 % at 300 kHz
Package
MLPQ 5 mm x 5 mm
Notebook, desktop and server computers
Digital HDTV and digital consumer applications
Networking and telecommunication equipment
Printers, DSL and STB applications
Embedded applications
Point of load power supplies
TYPICAL APPLICATION CIRCUIT
3
7
2
EN-PSAVE
29
PGOOD
26
EN-LDO
32
31
Document Number: 69062
S10-1367-Rev. D, 14-Jun-10
DH
V5V
12
VIN
6
BST
8
VLDO
FBL
EN/PSV
PGOOD
LX
13
PWM
Controller
27
ILIM
15
ENL
tON
AGND
30
1
FB DL
14
PGND
5
VOUT
www.vishay.com
1
SiC417
Vishay Siliconix
LX
PGOOD
ILIM
LX
EN/PSV
AGND
tON
ENL
PIN CONFIGURATION
LX
FB
PAD 1
FBL
LX
AGND 34
V5V
PGND
AGND
VOUT
PAD 3
PGND
LX 33
PGND
VIN
PAD 2
PGND
VLDO
VIN 35
PGND
BST
PGND
PGND
LX
DL
DH
VIN
VIN
VIN
PGND
PIN DESCRIPTION
Pin Number
Symbol
1
FB
2
FBL
3
V5V
4, 30, PAD 1
AGND
Description
Feedback input for switching regulator. Connect to an external resistor divider from output to program the
output voltage.
Feedback input for the LDO. Connect to an external resistor divider from VLDO to program the VLDO output.
5 V power input for internal analog circuits and gate drives. Connect to external 5 V supply or configure the
LDO for 5 V and connect to VLDO .
Analog ground.
5
VOUT
Output voltage input to the SiC417. Additionally, may be used to bypass LDO to supply VLDO directly.
6, 9 - 11, PAD 2
VIN
7
VLDO
8
BST
12
DH
LDO output.
Bootstrap pin. A capacitor is connected between BST to LX to develop the floating voltage for the high-side
gate drive.
High-side gate drive - do not connect this pin.
14
13, 23 - 25, 28,
PAD 3
15-22
DL
Low-side gate drive - do not connect this pin.
LX
Switching (Phase) node.
PGND
26
PGOOD
27
ILIM
29
EN/PSV
Input supply voltage.
31
tON
Power ground.
Open-drain power good indicator. High impedance indicates power is good. An external pull-up resistor is
required.
Current limit sense point - to program the current limit connect a resistor from ILIM to LX.
Tri-state pin. Enable input for switching regulator. Connect EN to AGND to disable the switching regulator.
Float pin for forced continuous and pull high for power-save mode.
On-time set input. Set the on-time by a series resistor to the input supply voltage.
32
ENL
Enable input for the LDO. Connect ENL to AGND to disable the LDO.
ORDERING INFORMATION
www.vishay.com
2
Part Number
SiC417CD-T1-E3
Package
MLPQ55-32
SiC417DB
Evaluation board
Document Number: 69062
S10-1367-Rev. D, 14-Jun-10
SiC417
Vishay Siliconix
FUNCTIONAL BLOCK DIAGRAM
3
V5V
6, 9 - 11 PAD 3
VIN
VIN
29
26
PGD
V5V
EN/PSV
AGND
1.20.21
PAD 1
V5V
Reference
BST
Control and Status
8
DL
Soft Start
+
FB
1
Gate Drive
Control
tON
31
VOUT
5
LX
13, 23 - 25
28, PAD 3
V5V
PGND
FB Comparator
15-22
Zero Cross
Detector
Bypass Comparator
ILIM
Valley 1 - Limit
VLDO
7
A
Y B
FBL
27
VIN
LDO
MUX
2
32
ENL
ABSOLUTE MAXIMUM RATINGS TA = 25 °C, unless otherwise noted
Parameter
Symbol
Min.
Max.
LX to PGND Voltage
VLX
- 0.3
+ 30
LX to PGND Voltage (transient - 100 ns)
VLX
-2
+ 30
VIN to PGND Voltage
VIN
- 0.3
+ 30
VEN Maximum Voltage
VEN
- 0.3
VIN
BST Bootstrap to LX; V5V to PGND
- 0.3
+ 6.0
AGND to PGND
- 0.3
+ 0.3
EN/PSV, PGOOD, ILIM, VOUT, VLDO, FB, FBL to GND
- 0.3
+ (V5V + 0.3)
tON to PGND
- 0.3
+ (V5V - 1.5)
BST to PGND
- 0.3
+ 35
VAG-PG
Unit
V
Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only,
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is
not implied. Exposure to absolute maximum rating/conditions for extended periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
Parameter
Symbol
Min.
VIN
3.0
28
V5V to PGND
V5V
4.5
5.5
VOUT to PGND
VOUT
0.5
5.5
Input Voltage
Typ.
Max.
Unit
V
Note:
For proper operation, the device should be used within the recommended conditions.
THERMAL RESISTANCE RATINGS
Parameter
Storage Temperature
Symbol
Min.
Typ.
Max.
TSTG
- 40
+ 150
Maximum Junction Temperature
TJ
-
150
Operation Junction Temperature
TJ
- 25
+ 125
Document Number: 69062
S10-1367-Rev. D, 14-Jun-10
Unit
°C
www.vishay.com
3
SiC417
Vishay Siliconix
THERMAL RESISTANCE RATINGS
Thermal Resistance, Junction-to-Ambientb
High-Side MOSFET
Low-Side MOSFET
PWM Controller and LDO Thermal Resistance
25
20
50
°C/W
Peak IR Reflow Temperature
TReflow
260
°C
Notes:
a. This device is ESD sensitive. Use of standard ESD handling precautions is required.
b. Calculated from package in still air, mounted to 3 x 4.5 (in), 4 layer FR4 PCB with thermal vias under the exposed pad per JESD51 standards.
Exceeding the above specifications may result in permanent damage to the device or device malfunction. Operation outside of the parameters
specififed in the Electrical Characteristicsw section is not recommended.
ELECTRICAL SPECIFICATIONS
Parameter
Symbol
Test Conditions Unless Specified
VIN = 12 V, V5V = 5 V, TA = + 25 °C for typ.,
- 25 °C to + 85 °C for min. and max.,
TJ = < 125 °C
Min.
Typ.
Max.
Unit
Input Supplies
VIN Input Voltage
VIN
3
28
V5V Voltage
V5V
4.5
5.5
VIN UVLO Threshold Voltagea
VIN UVLO Hysteresis
V5V UVLO Threshold Voltage
V5V UVLO Hysteresis
VIN Supply Current
V5V Supply Current
VIN_UV+
Sensed at ENL pin, rising edge
2.4
2.6
2.95
VIN_UV-
Sensed at ENL pin, falling edge
2.235
2.4
2.565
VIN_UV_HY
EN/PSV = High
0.2
V5V_UV+
Measured at V5V pin, rising edge
3.7
3.9
4.1
V5V_UV-
Measured at V5V pin, falling edge
3.5
3.6
3.75
0.3
V5V_UV_HY
IIN
I5V
V
EN/PSV, ENL = 0 V, VIN = 28 V
8.5
Standby mode:
ENL = V5V, EN/PSV = 0 V
130
EN/PSV, ENL = 0 V
3
EN/PSV = V5V, no load (fSW = 25 kHz),
VFB > 500 mVb
20
µA
7
2
b
fSW = 250 kHz, EN/PSV = floating, no load
mA
10
Controller
FB On-Time Threshold
VFB-TH
Static VIN and load, - 40 °C to + 85 °C
0.495
Frequency Range
FPWM
continuous mode
200
Bootstrap Switch Resistance
0.5
0.505
V
1000
kHz
Ω
10
Timing
Continuous mode operation VIN = 15 V,
VOUT = 5 V, fSW = 300 kHz, Rton = 133 kΩ
999
1110
On-Time
tON
Minimum On-Timeb
tON
50
Minimum Off-Timeb
tOFF
250
1220
ns
Soft Start
Soft Start Timeb
tSS
IOUT = ILIM/2
0.85
ms
500
kΩ
Analog Inputs/Outputs
VOUT Input Resistance
RO-IN
Current Sense
Zero-Crossing Detector Threshold Voltage
VSense-th
LX-PGND
-3
- 10 %
0
+3
mV
Power Good
PG_VTH
Internal reference 500 mV
Start-Up Delay Time
PG_Td
VEN = 0 V
2
Fault (noise-immunity) Delay Timeb
PG_ICC
VEN = 0 V
5
Power Good Leakage Current
PG_ILK
VEN = 0 V
PG_RDS-ON
VEN = 0 V
Power Good Threshold Voltage
Power Good On-Resistance
www.vishay.com
4
+ 20 %
µs
1
10
V
ms
µA
Ω
Document Number: 69062
S10-1367-Rev. D, 14-Jun-10
SiC417
Vishay Siliconix
ELECTRICAL SPECIFICATIONS
Test Conditions Unless Specified
VIN = 12 V, V5V = 5 V, TA = + 25 °C for typ.,
- 25 °C to + 85 °C for min. and max.,
TJ = < 125 °C
Min.
RILIM = 5.9 kΩ
6
8
10
A
VILM-LK
With respect to AGND
- 10
0
+ 10
mV
Output Under-Voltage Fault
VOUV_Fault
VFB with respect to Internal 500 mV reference,
8 consecutive clocks
- 25
Smart Power-Save Protection
Threshold Voltageb
PSAVE_VTH
VFB with respect to internal 500 mV reference
+ 10
VFB with respect to internal 500 mV reference
+ 20
5
µs
10 °C hysteresis
150
°C
Parameter
Symbol
Typ.
Max.
Unit
Fault Protection
ILIM Source Current
ILIM
10
Valley Current Limit
ILIM Comparator Offset Voltage
Over-Voltage Protection Threshold
Over-Voltage Fault Delayb
tOV-Delay
Over Temperature Shutdownb
TShut
µA
%
%
Logic Inputs/Outputs
Logic Input High Voltage
VIN+
Logic Input Low Voltage
VIN-
EN/PSV Input Bias Current
IEN-
2
EN, ENL, PSV
0.4
EN/PSV = V5V or AGND
- 10
VIN = 28 V
ENL Input Bias Current
FBL, FB Input Bias Current
FBL_ILK
+ 10
11
FBL, FB = V5V or AGND
-1
VLDO load = 10 mA
0.735
V
18
µA
+1
Linear Dropout Regulator
FBL Accuracy
FBLACC
LDO Current Limit
Start-up and foldback, VIN = 12 V
LDO_ILIM
Operating current limit, VIN = 12 V
0.75
0.765
85
135
mA
200
VLDO to VOUT Switch-Over Thresholdc
VLDO-BPS
- 140
+ 140
VLDO to VOUT Non-Switch-Over Thresholdc
VLDO-NBPS
- 450
+ 450
VLDO to VOUT Switch-Over Resistance
LDO Drop Out Voltage
mV
VOUT = 5 V
2
Ω
From VIN to VVLDO, VVLDO = + 5 V,
IVLDO = 100 mA
1.2
V
RLDO
d
V
Notes:
a. VIN UVLO is programmable using a resistor divider from VIN to ENL to AGND. The ENL voltage is compared to an internal reference.
b. Guaranteed by design.
c. The switch-over threshold is the maximum voltage diff erential between the VLDO and VOUT pins which ensures that VLDO will internally
switch-over to VOUT. The non-switch-over threshold is the minimum voltage diff erential between the VLDO and VOUT pins which ensures that
VLDO will not switch-over to VOUT.
d. The LDO drop out voltage is the voltage at which the LDO output drops 2 % below the nominal regulation point.
ELECTRICAL CHARACTERISTICS
100
95
VIN = 9 V
90
VIN = 19 V
Efficiency (%)
85
80
75
70
65
60
55
50
0
1
2
3
4
5
6
7
8
9
10
IOUT (A)
Efficiency vs. Output Current (VOUT = 1.2 V)
Document Number: 69062
S10-1367-Rev. D, 14-Jun-10
www.vishay.com
5
SiC417
Vishay Siliconix
ELECTRICAL CHARACTERISTICS
1.35
300
250
1.3
VIN = 19 V
200
VOUT (V)
Frequency (kHz)
VIN = 9 V
150
VIN = 9 V
1.25
VIN = 19 V
100
1.2
50
0
1.15
0
1
2
3
4
5
6
7
8
9
10
IOUT (A)
Frequency vs. IOUT, (VOUT = 1.2 V)
0
1
2
3
4
5
6
7
8
9
10
IOUT (A)
Load Regulation, (VOUT = 1.2 V)
Start up Time: VIN = 12 V, VOUT = 1.2 V, IOUT = 0 A
PGOOD Delay after Start up Time:
VIN = 12 V, VOUT = 1.2 V, IOUT = 0 A
Transient Response: VIN = 12 V, VOUT = 1.2 V,
IOUT = 10 A to 5 A, dI/dt = 0.5 A/µs
Transient Response: VIN = 12 V, VOUT = 1.2 V,
IOUT = 5 A to 10 A, dI/dt = 0.5 A/µs
www.vishay.com
6
Document Number: 69062
S10-1367-Rev. D, 14-Jun-10
SiC417
Vishay Siliconix
ELECTRICAL CHARACTERISTICS
Ultra-Sonic Power-Save at IOUT = 0 A
Over Current Protection: VIN = 12 V, VOUT = 1.2 V
APPLICATIONS INFORMATION
SiC417 Synchronous Buck Converter
The SiC417 is a step down synchronous buck dc-to-dc
converter with integrated power FETs and programmable
LDO. The SiC417 is capable of 10 A operation at very high
efficiency in a tiny 5 mm x 5 mm - 32 pin package. The
programmable operating frequency range of 200 kHz to
1 MHz, enables the user to optimize the solution for minimum
board space and optimum efficiency.
The buck controller employs pseudo-fixed frequency
adaptive on-time control. This control scheme allows fast
transient response thereby lowering the size of the power
components used in the system.
tON
VIN
VLX
CIN
VFB
Q1
VLX
FB threshold
VOUT
L
Q2
ESR
FB
+
Input Voltage Range
The SiC417 requires two input supplies for normal operation:
VIN and V5V. VIN operates over the wide range from 3 V to
28 V. V5V requires a 5 V supply input that can be an external
source or the internal LDO configured to supply 5 V. When
VIN is less than ~ 6 V then an external 5 V supply must be
tied to V5V.
Pseudo-Fixed Frequency Adaptive On-Time Control
The PWM control method used for the SiC417 is
pseudo-fixed frequency, adaptive on-time, as shown in
figure 1. The ripple voltage generated at the output capacitor
ESR is used as a PWM ramp signal. This ripple is used to
trigger the on-time of the controller.
The adaptive on-time is determined by an internal oneshot
timer. When the one-shot is triggered by the output ripple, the
device sends a single on-time pulse to the highside
MOSFET. The pulse period is determined by VOUT and VIN;
the period is proportional to output voltage and inversely
proportional to input voltage. With this adaptive on-time
arrangement, the device automatically anticipates the
on-time needed to regulate VOUT for the present VIN
condition and at the selected frequency.
Document Number: 69062
S10-1367-Rev. D, 14-Jun-10
COUT
Figure 1 - Output Ripple and PWM Control Method
The adaptive on-time control has significant advantages over
traditional control methods used in the controllers today.
• Reduced component count by eliminating DCR sense or
current sense resistor as no need of a sensing inductor
current.
• Reduced Saves external components used for
compensation by eliminating the no error amplifier and
other components.
• Ultra fast transient response because of fast loop,
absence of error amplifier speeds up the transient
response.
• Predictable frequency spread because of constant on-time
architecture.
• Fast transient response enables operation with minimum
output capacitance
Overall, superior performance compared to fixed frequency
architectures.
www.vishay.com
7
SiC417
Vishay Siliconix
On-Time One-Shot Generator (tON) and Operating
Frequency
The SiC417 have an internal on-time one-shot generator
which is a comparator that has two inputs. The FB
Comparator output goes high when VFB is less than the
internal 500 mV reference. This feeds into the gate drive and
turns on the high-side MOSFET, and also starts the one-shot
timer. The one-shot timer uses an internal comparator and a
capacitor. One comparator input is connected to VOUT, the
other input is connected to the capacitor. When the on-time
begins, the internal capacitor charges from zero volts
through a current which is proportional to VIN. When the
capacitor voltage reaches VOUT, the on-time is completed
and the high-side MOSFET turns off. The figure 2 shows the
on-chip implementation of on-time generation.
FB comparator
FB
500 mV
+
VOUT
VIN
Rton
DH
Q1
VLX
DL
Q2
VOUT
L
ESR
COUT
FB
+
On-time = K x Rton x (VOUT/VIN)
Figure 2 - On-Time Generation
This method automatically produces an on-time that is
proportional to VOUT and inversely proportional to VIN. Under
steady-state conditions, the switching frequency can be
determined from the on-time by the following equation.
fSW =
VOUT
tON x VIN
The SiC417 uses an external resistor to set the ontime which
indirectly sets the frequency. The on-time can be
programmed to provide operating frequency from 200 kHz to
1 MHz using a resistor between the tON pin and ground. The
resistor value is selected by the following equation.
(t - 10 ns) x VIN
Rton = ON
25 pF x VOUT
The maximum RTON value allowed is shown by the following
equation.
Rton_MAX =
R1
R2
Figure 3 - Output Voltage Selection
As the control method regulates the valley of the output ripple
voltage, the DC output voltage VOUT is off set by the output
ripple according to the following equation.
VOUT = 0.5 x (1 + R1/R2) + VRIPPLE/2
Gate
drives
One-shot
timer
To FB pin
VOUT
VIN_MIN
15 µA
Enable and Power-Save Inputs
The EN/PSV and ENL inputs are used to enable or disable
the switching regulator and the LDO.
When EN/PSV is low (grounded), the switching regulator is
off and in its lowest power state. When off, the output of the
switching regulator soft-discharges the output into a 15 Ω
internal resistor via the VOUT pin.
When EN/PSV is allowed to float, the pin voltage will fl oat to
1.5 V. The switching regulator turns on with power-save
disabled and all switching is in forced continuous mode.
When EN/PSV is high (above 2.0 V), the switching regulator
turns on with ultra-sonic power-save enabled. The SiC417
ultra-sonic power-save operation maintains a minimum
switching frequency of 25 kHz, for applications with stringent
audio requirements.
The ENL input is used to control the internal LDO. This input
serves a second function by acting as a VIN UVLO sensor for
the switching regulator.
The LDO is off when ENL is low (grounded). When ENL is a
logic high but below the VIN UVLO threshold (2.6 V typical),
then the LDO is on and the switcher is off. When ENL is
above the VIN UVLO threshold, the LDO is enabled and the
switcher is also enabled if the EN/PSV pin is not grounded.
Forced Continuous Mode Operation
The SiC417 operates the switcher in Forced Continuous
Mode (FCM) by floating the EN/PSV pin (see figure 4). In this
mode one of the power MOSFETs is always on, with no
intentional dead time other than to avoid cross-conduction.
This feature results in uniform frequency across the full load
range with the trade-off being poor efficiency at light loads
due to the high-frequency switching of the MOSFETs.
VOUT Voltage Selection
The switcher output voltage is regulated by comparing VOUT
as seen through a resistor divider at the FB pin to the internal
500 mV reference voltage, see figure 3.
www.vishay.com
8
Document Number: 69062
S10-1367-Rev. D, 14-Jun-10
SiC417
Vishay Siliconix
FB ripple
voltage (VFB)
FB threshold
(500 mV)
DC load current
Inductor
current
On-time
(tON)
DH on-time is triggered when
VFB reaches the FB threshold
DH
Because the on-times are forced to occur at intervals no
greater than 40 µs, the frequency will not fall below ~ 25 kHz.
Figure 5 shows ultra-sonic power-save operation.
Benefits of Ultrasonic Power-Save
Having a fixed minimum frequency in power-save has some
significant advantages as below:
• The minimum frequency of 25 kHz is outside the audible
range of human ear. This makes the operation of the
SiC417 very quiet.
• The output voltage ripple seen in power-save mode is
significant lower than conventional power-save, which
improves efficiency at light loads.
• Lower ripple in power-save also makes the power
component selection easier.
DL
DL drives high when on-time is completed.
DL remains high until VFB falls to the FB threshold.
Figure 4 - Forced Continuous Mode Operation
Ultrasonic Power-Save Operation
The SiC417 provides ultra-sonic power-save operation at
light loads, with the minimum operating frequency fixed at
25 kHz. This is accomplished using an internal timer that
monitors the time between consecutive high-side gate
pulses.
If the time exceeds 40 µs, DL drives high to turn the low-side
MOSFET on. This draws current from VOUT through the
inductor, forcing both VOUT and VFB to fall. When VFB drops
to the 500 mV threshold, the next DH on-time is triggered.
After the on-time is completed the high-side MOSFET is
turned off and the low-side MOSFET turns on, the low-side
MOSFET remains on until the inductor current ramps down
to zero, at which point the low-side MOSFET is turned off.
Figure 6 - Ultrasonic Power-Save Operation Mode
Figure 6 shows the behavior under power-save and
continuous conduction mode at light loads.
minimum fSW ~ 25 kHz
FB ripple
voltage (VFB)
FB threshold
(500 mV)
(0A)
Inductor
current
On-time
(tON)
DH on-time is triggered when
VFB reaches the FB threshold
DH
DL
Smart Power-Save Protection
Active loads may leak current from a higher voltage into the
switcher output. Under light load conditions with powersavepower-save enabled, this can force VOUT to slowly rise
and reach the over-voltage threshold, resulting in a hard
shutdown. Smart power-save prevents this condition.
When the FB voltage exceeds 10 % above nominal (exceeds
550 mV), the device immediately disables power-save, and
DL drives high to turn on the low-side MOSFET. This draws
current from VOUT through the inductor and causes VOUT to
fall. When VFB drops back to the 500 mV trip point, a normal
tON switching cycle begins.
This method prevents a hard OVP shutdown and also cycles
energy from VOUT back to VIN. It also minimizes operating
power by avoiding forced conduction mode operation.
Figure 7 shows typical waveforms for the smart power-save
feature.
After the 40 µs time-out, DL drives high if VFB
has not reached the FB threshold.
Figure 5 - Ultrasonic power-save Operation
Document Number: 69062
S10-1367-Rev. D, 14-Jun-10
www.vishay.com
9
SiC417
Vishay Siliconix
VOUT drifts up to due to leakage
current flowing into COUT
Smart power save
threshold (550 mV)
VOUT discharges via inductor
and low-side MOSFET
Normal VOUT ripple
FB
threshold
DH and DL off
High-side
drive (DH)
Single DH on-time pulse
after DL turn-off
Low-side
drive (DL)
DL turns on when smart
PSAVE threshold is reached
DL turns off FB
threshold is reached
Normal DL pulse after DH
on-time pulse
Figure 7 - Smart Power-Save
Current Limit Protection
The SiC417 features programmable current limit capability,
which is accomplished by using the RDS(ON) of the lower
MOSFET for current sensing. The current limit is set by RILIM
resistor. The RILIM resistor connects from the ILIM pin to the
LX pin which is also the drain of the low-side MOSFET.
When the low-side MOSFET is on, an internal ~ 10 µA
current flows from the ILIM pin and the RILIM resistor, creating
a voltage drop across the resistor. While the low-side
MOSFET is on, the inductor current flows through it and
creates a voltage across the RDS(ON). The voltage across the
MOSFET is negative with respect to ground.
If this MOSFET voltage drop exceeds the voltage across
RILIM, the voltage at the ILIM pin will be negative and current
limit will activate. The current limit then keeps the low-side
MOSFET on and will not allow another high-side on-time,
until the current in the low-side MOSFET reduces enough to
bring the ILIM voltage back up to zero. This method regulates
the inductor valley current at the level shown by ILIM in
figure 8.
Inductor Current
IPEAK
ILOAD
ILIM
Time
Figure 8 - Valley Current Limit
Setting the valley current limit to 10 A results in a 10 A peak
inductor current plus peak ripple current. In this situation, the
average (load) current through the inductor is 10 A plus
one-half the peak-to-peak ripple current.
The internal 10 µA current source is temperature
compensated at 4100 ppm in order to provide tracking with
the RDS(ON). The RILIM value is calculated by the following
equation.
RILIM = 735 x ILIM
www.vishay.com
10
Note that because the low-side MOSFET with low RDS(ON) is
used for current sensing, the PCB layout, solder
connections, and PCB connection to the LX node must be
done carefully to obtain good results. Refer to the layout
guidelines for information.
Soft-Start of PWM Regulator
Soft-start is achieved in the PWM regulator by using an
internal voltage ramp as the reference for the FB
Comparator. The voltage ramp is generated using an internal
charge pump which drives the reference from zero to 500 mV
in ~ 1.2 mV increments, using an internal ~ 500 kHz
oscillator. When the ramp voltage reaches 500 mV, the ramp
is ignored and the FB comparator switches over to a fixed
500 mV threshold. During soft-start the output voltage tracks
the internal ramp, which limits the start-up inrush current and
provides a controlled softstart profile for a wide range of
applications. Typical softstart ramp time is 850 µs. During
soft-start the regulator turns off the low-side MOSFET on any
cycle if the inductor current falls to zero. This prevents
negative inductor current, allowing the device to start into a
pre-biased output.
Power Good Output
The power good (PGOOD) output is an open-drain output
which requires a pull-up resistor. When the output voltage is
10 % below the nominal voltage, PGOOD is pulled low. It is
held low until the output voltage returns above - 8 % of
nominal. PGOOD is held low during start-up and will not be
allowed to transition high until soft-start is completed (when
VFB reaches 500 mV) and typically 2 ms has passed.
PGOOD will transition low if the VFB pin exceeds + 20 % of
nominal, which is also the over-voltage shutdown threshold
(600 mV). PGOOD also pulls low if the EN/PSV pin is low
when V5V is present.
Output Over-Voltage Protection
Over-voltage protection becomes active as soon as the
device is enabled. The threshold is set at 500 mV + 20 %
(600 mV). When VFB exceeds the OVP threshold, DL latches
high and the low-side MOSFET is turned on. DL remains
high and the controller remains off , until the EN/PSV input is
toggled or V5V is cycled. There is a 5 µs delay built into the
OVP detector to prevent false transitions. PGOOD is also low
after an OVP event.
Output Under-Voltage Protection
When VFB falls 25 % below its nominal voltage (falls to
375 mV) for eight consecutive clock cycles, the switcher is
shut off and the DH and DL drives are pulled low to tristate
the MOSFETs. The controller stays off until EN/PSV is
toggled or V5V is cycled.
V5V UVLO, and POR
Under-voltage lock-out (UVLO) circuitry inhibits switching
and tri-states the DH/DL drivers until V5V rises above 3.9 V.
An internal Power-On Reset (POR) occurs when V5V
exceeds 3.9 V, which resets the fault latch and soft-start
Document Number: 69062
S10-1367-Rev. D, 14-Jun-10
SiC417
Vishay Siliconix
counter to prepare for soft-start. The SiC417 then begins a
soft-start cycle. The PWM will shut off if V5V falls below
3.6 V.
LDO Regulator
The SiC417 features an integrated LDO regulator with a
programmable output voltage from 0.75 V to 5.25 V using
external resistors, when an external supply is used to power
V5V. The feedback pin (FBL) for the LDO is regulated to 750
mV. There is also an enable pin (ENL) for the LDO that
provides independent control. The LDO voltage can also be
used to provide the bias voltage for the switching regulator,
when VLDO is tied to V5V. More detail can be found in the On
Chip LDO bias section coming up.
To FBL pin
VLDO
RLDO1
RLDO2
Figure 9 - LDO Start-Up
The LDO output voltage is set by the following equation.
VLDO = 750 mV x 1+
(
RLDO1
RLDO2
)
A minimum capacitance of 1 µF referenced to AGND is
normally required at the output of the LDO for stability. If the
LDO is providing bias power to the device, then a minimum
0.1 µF capacitor referenced to AGND is required along with a
minimum 1.0 µF capacitor referenced to PGND to filter the
gate drive pulses. Refer to the layout guideline section.
LDO Start-up
Before start-up, the LDO checks the status of the following
signals to ensure proper operation can be maintained.
1. ENL pin
2. VLDO output
3. VIN input voltage
When the ENL pin is high and VIN is above the UVLO point,
the LDO will begin start-up. During the initial phase, when the
LDO output voltage is near zero, the LDO initiates a
current-limited start-up (typically 85 mA) to charge the output
capacitor. When VLDO has reached 90 % of the final value
(as sensed at the FBL pin), the LDO current limit is increased
to ~ 200 mA and the LDO output is quickly driven to the
nominal value by the internal LDO regulator.
VVLDO final
Voltage regulating with
~ 200 mA current limit
90 % of VVLDO final
Constant current startup
LDO Switchover Function
The SiC417 includes a switch-over function for the LDO. The
switch-over function is designed to increase efficiency by
using the more efficient dc-to-dc converter to power the LDO
output, avoiding the less efficient LDO regulator when
possible. The switch-over function connects the VLDO pin
directly to the VOUT pin using an internal switch. When the
switch-over is complete the LDO is turned off, which results
in a power savings and maximizes efficiency. If the LDO
output is used to bias the SiC417, then after switch-over the
device is self-powered from the switching regulator with the
LDO turned off.
The switch-over logic waits for 32 switching cycles before it
starts the switch-over. There are two methods that determine
the switch-over of VLDO to VOUT.
In the first method, the LDO is already in regulation and the
dc-to-dc converter is later enabled. As soon as the PGOOD
output goes high, the 32 cycles are started. The voltages at
the VLDO and VOUT pins are then compared; if the two
voltages are within ± 300 mV of each other, the VLDO pin
connects to the VOUT pin using an internal switch, and the
LDO is turned off.
In the second method, the dc-to-dc converter is already
running and the LDO is enabled. In this case the 32 cycles
are started as soon as the LDO reaches 90 % of its final
value. At this time, the VLDO and VOUT pins are compared,
and if within ± 300 mV the switch-over occurs and the LDO
is turned off.
Benefits of having a switchover circuit
The switchover function is designed to get maximum
efficiency out of the dc-to-dc converter. The efficiency for an
LDO is very low especially for high input voltages. Using the
switchover function we tie any rails connected to VLDO
through a switch directly to VOUT. Once switchover is
complete LDO is turned off which saves power. This gives us
the maximum efficiency out of the SiC417.
If the LDO output is used to bias the SiC417, then after
switchover the VOUT self biases the SiC417 and operates in
self-powered mode.
Steps to follow when using the on chip LDO to bias the
SiC417:
• Always tie the V5V to VLDO before enabling the LDO
• Enable the LDO before enabling the switcher
• LDO has a current limit of 85 mA at start-up with 12 VIN, so
do not connect any load between VLDO and ground
• The current limit for the LDO goes up to 200 mA once the
VLDO reaches 90 % of its final values and can easily supply
the required bias current to the IC.
Switch-over Limitations on VOUT and VLDO
Because the internal switch-over circuit always compares
the VOUT and VLDO pins at start-up, there are limitations on
permissible combinations of VOUT and VLDO. Consider the
case where VOUT is programmed to 1.5 V and VLDO is
programmed to 1.8 V. After start-up, the device would
connect VOUT to VLDO and disable the LDO, since the two
voltages are within the ± 300 mV switch-over window.
Figure 10 - LDO Start-Up
Document Number: 69062
S10-1367-Rev. D, 14-Jun-10
www.vishay.com
11
SiC417
Vishay Siliconix
To avoid unwanted switch-over, the minimum difference
between the voltages for VOUT and VLDO should be
± 500 mV.
It is not recommended to use the switch-over feature for an
output voltage less than 3 V since this does not provide
sufficient voltage for the gate-source drive to the internal
p-channel switch-over MOSFET.
Switch-Over MOSFET Parasitic Diodes
The switch-over MOSFET contains parasitic diodes that are
inherent to its construction, as shown in figure 11.
Switchover
control
Switchover
MOSFET
VOUT
VLDO
Parastic diode
Parastic diode
V5V
Figure 11 - Switch-over MOSFET Parasitic Diodes
There are some important design rules that must be followed
to prevent forward bias of these diodes. The following two
conditions need to be satisfied in order for the parasitic
diodes to stay off.
• V5V ≥ VLDO
• V5V ≥ VOUT
If either VLDO or VOUT is higher than V5V, then the respective
diode will turn on and the SiC417 operating current will flow
through this diode. This has the potential of damaging the
device.
ENL Pin and VIN UVLO
The ENL pin also acts as the switcher under-voltage lockout
for the VIN supply. The VIN UVLO voltage is programmable
via a resistor divider at the VIN, ENL and AGND pins.
ENL is the enable/disable signal for the LDO. In order to
implement the VIN UVLO there is also a timing requirement
that needs to be satisfied.
If the ENL pin transitions low within 2 switching cycles and is
< 1 V, then the LDO will turn off but the switcher remains on.
If ENL goes below the VIN UVLO threshold and stays above
1 V, then the switcher will turn off but the LDO remains on.
The VIN UVLO function has a typical threshold of 2.6 V on the
VIN rising edge. The falling edge threshold is 2.4 V.
Note that it is possible to operate the switcher with the LDO
disabled, but the ENL pin must be below the logic low
threshold (0.4 V maximum).
However, if the switcher was previously operating (with EN/
PSV high but ENL at ground, and V5V supplied externally),
then it is undesirable to shut down the switcher.
To prevent this, when the ENL input is taken above 2.6 V
(above the VIN UVLO threshold), the internal logic checks the
PGOOD signal. If PGOOD is high, then the switcher is already
running and the LDO will run through the start-up cycle
without affecting the switcher. If PGOOD is low, then the LDO
will not allow any PWM switching until the LDO output has
reached 90 % of it's final value.
On-Chip LDO Bias the SiC417
The following steps must be followed when using the onchip
LDO to bias the device.
• Connect V5V to VLDO before enabling the LDO.
• The LDO has an initial current limit of 85 mA at start-up
with 12 VIN, therefore, do not connect any external load to
VLDO during start-up.
• When VLDO reaches 90 % of its final value, the LDO
current limit increases to 200 mA. At this time the LDO may
be used to supply the required bias current to the device.
• Switching will be held off until VLDO reaches regulation.
Attempting to operate in self-powered mode in any other
configuration can cause unpredictable results and may
damage the device.
Design Procedure
When designing a switch mode power supply, the input
voltage range, load current, switching frequency, and
inductor ripple current must be specified.
The maximum input voltage (VINMAX) is the highest specified
input voltage. The minimum input voltage (VINMIN) is
determined by the lowest input voltage after evaluating the
voltage drops due to connectors, fuses, switches, and PCB
traces.
The following parameters define the design:
• Nominal output voltage (VOUT)
• Static or DC output tolerance
• Transient response
• Maximum load current (IOUT)
There are two values of load current to evaluate - continuous
load current and peak load current. Continuous load current
relates to thermal stresses which drive the selection of the
inductor and input capacitors. Peak load current determines
instantaneous
component
stresses
and
filtering
requirements such as inductor saturation, output capacitors,
and design of the current limit circuit.
The following values are used in this design:
• VIN = 12 V ± 10 %
• VOUT = 1.05 V ± 4 %
• fSW = 250 kHz
• Load = 10 A maximum
ENL Logic Control of PWM Operation
When the ENL input is driven above 2.6 V, it is impossible to
determine if the LDO output is going to be used to power the
device or not. In self-powered operation where the LDO will
power the device, it is necessary during the LDO start-up to
hold the PWM switching off until the LDO has reached 90 %
of the final value. This is to prevent overloading the
current-limited LDO output during the LDO start-up.
www.vishay.com
12
Document Number: 69062
S10-1367-Rev. D, 14-Jun-10
SiC417
Vishay Siliconix
Frequency Selection
Selection of the switching frequency requires making a
trade-off between the size and cost of the external filter
components (inductor and output capacitor) and the power
conversion efficiency.
The desired switching frequency is 250 kHz which results
from using component selected for optimum size and cost.
A resistor (RTON) is used to program the on-time (indirectly
setting the frequency) using the following equation.
(t - 10 ns) x VIN
Rton = ON
25 pF x VOUT
To select RTON, use the maximum value for VIN, and for tON
use the value associated with maximum VIN.
tON =
VOUT
VINMAX. x fSW
tON = 318 ns at 13.2 VIN, 1.05 VOUT, 250 kHz
Substituting for RTON results in the following solution
RTON = 154.9 kΩ, use RTON = 154 kΩ.
Inductor Selection
In order to determine the inductance, the ripple current must
first be defined. Low inductor values result in smaller size but
create higher ripple current which can reduce efficiency.
Higher inductor values will reduce the ripple current and
voltage and for a given DC resistance are more efficient.
However, larger inductance translates directly into larger
packages and higher cost. Cost, size, output ripple, and
efficiency are all used in the selection process.
The ripple current will also set the boundary for power-save
operation. The switching will typically enter power-save
mode when the load current decreases to 1/2 of the ripple
current. For example, if ripple current is 4 A then power-save
operation will typically start for loads less than 2 A. If ripple
current is set at 40 % of maximum load current, then powersave will start for loads less than 20 % of maximum current.
The inductor value is typically selected to provide a ripple
current that is between 25 % to 50 % of the maximum load
current. This provides an optimal trade-off between cost,
efficiency, and transient performance.
During the DH on-time, voltage across the inductor is
(VIN-VOUT). The equation for determining inductance is
shown next.
Note that the inductor must be rated for the maximum DC
load current plus 1/2 of the ripple current. The ripple current
under minimum VIN conditions is also checked using the
following equations.
TON_VINMIN =
IRIPPLE =
25 pF x RTON x VOUT
VINMIN
(VIN - VOUT) x TON
L
IRIPPLE_VIN =
(10.8 - 1.05) x 384 ns
= 4.25 A
0.88 µH
Capacitor Selection
The output capacitors are chosen based on required ESR
and capacitance. The maximum ESR requirement is
controlled by the output ripple requirement and the DC
tolerance. The output voltage has a DC value that is equal to
the valley of the output ripple plus 1/2 of the peak-to-peak
ripple. Change in the output ripple voltage will lead to a
change in DC voltage at the output.
The design goal is that the output voltage regulation be
± 4 % under static conditions. The internal 500 mV reference
tolerance is 1 %. Allowing 1 % tolerance from the FB resistor
divider, this allows 2 % tolerance due to VOUT ripple.
Since this 2 % error comes from 1/2 of the ripple voltage, the
allowable ripple is 4 %, or 42 mV for a 1.05 V output.
The maximum ripple current of 4.4 A creates a ripple voltage
across the ESR. The maximum ESR value allowed is shown
by the following equations.
ESRMAX =
VRIPPLE
IRIPPLEMAX
L=
(13.2 - 1.05) x 318 ns
= 77 µH
5A
A slightly larger value of 0.88 µH is selected. This will
decrease the maximum IRIPPLE to 4.4 A.
Document Number: 69062
S10-1367-Rev. D, 14-Jun-10
4.4 A
The output capacitance is usually chosen to meet transient
requirements. A worst-case load release, from maximum
load to no load at the exact moment when inductor current is
at the peak, determines the required capacitance. If the load
release is instantaneous (load changes from maximum to
zero in < 1 µs), the output capacitor must absorb all the
inductor's stored energy. This will cause a peak voltage on
the capacitor according to the following equation.
1
xI
)2
2 RIPPLEMAX
(VPEAK)2 - (VOUT)2
L (IOUT +
(VIN - VOUT) x tON
IRIPPLE
Example
In this example, the inductor ripple current is set equal to
50 % of the maximum load current. Thus ripple current will be
50 % x 10 A or 5 A. To find the minimum inductance needed,
use the VIN and TON values that correspond to VINMAX.
42 mV
ESRMAX = 9.5 mΩ
COUTMIN =
L=
=
Assuming a peak voltage VPEAK of 1.150 (100 mV rise upon
load release), and a 10 A load release, the required
capacitance is shown by the next equation.
1
x 4.4)2
2
2
(1.15) - (1.05)2
0.88 µH (10 +
COUTMIN =
COUTMIN = 595 µF
If the load release is relatively slow, the output capacitance
can be reduced. At heavy loads during normal switching,
when the FB pin is above the 500 mV reference, the DL
www.vishay.com
13
SiC417
Vishay Siliconix
output is high and the low-side MOSFET is on. During this
time, the voltage across the inductor is approximately - VOUT.
This causes a down-slope or falling di/dt in the inductor. If the
load dI/dt is not much faster than the - dI/dt in the inductor,
then the inductor current will tend to track the falling load
current. This will reduce the excess inductive energy that
must be absorbed by the output capacitor, therefore a
smaller capacitance can be used.
The following can be used to calculate the needed
capacitance for a given dILOAD/dt:
Peak inductor current is shown by the next equation.
ILPK = IMAX + 1/2 x IRIPPLEMAX
ILPK = 10 + 1/2 x 4.4 = 12.2 A
Rate of change of load current = dILOAD/dt
IMAX = maximum load release = 10 A
I
I
L x LPK - MAX x dt
VOUT dlLOAD
COUT = ILPK x
2 (VPK - VOUT)
Example
Load
dlLOAD 2.5 A
=
µs
dt
This would cause the output current to move from 10 A to
zero in 4 µs as shown by the following equation.
12.2
10
x 1 µs
1.05
2.5
2 (1.15 - 1.05)
0.88 µH x
COUT = 12.2 x
COUT = 379 µF
Note that COUT is much smaller in this example, 379 µF
compared to 595 µF based on a worst-case load release. To
meet the two design criteria of minimum 379 µF and
maximum 9 mΩ ESR, select two capacitors rated at 220 µF
and 15 mΩ ESR.
It is recommended that an additional small capacitor be
placed in parallel with COUT in order to filter high frequency
switching noise.
Stability Considerations
Unstable operation is possible with adaptive on-time
controllers, and usually takes the form of double-pulsing or
ESR loop instability.
Double-pulsing occurs due to switching noise seen at the FB
input or because the FB ripple voltage is too low. This causes
the FB comparator to trigger prematurely after the 250 ns
minimum off-time has expired. In extreme cases the noise
can cause three or more successive on-times.
Double-pulsing will result in higher ripple voltage at the
output, but in most applications it will not affect operation.
This form of instability can usually be avoided by providing
the FB pin with a smooth, clean ripple signal that is at least
10 mVp-p, which may dictate the need to increase the ESR of
the output capacitors. It is also imperative to provide a proper
PCB layout as discussed in the Layout Guidelines section.
www.vishay.com
14
CTOP
VOUT
To FB pin
R1
R2
Figure 13 - Capacitor Coupling to FB Pin
Another way to eliminate doubling-pulsing is to add a small
(~ 10 pF) capacitor across the upper feedback resistor, as
shown in figure 13. This capacitor should be left unpopulated
until it can be confirmed that double-pulsing exists. Adding
the CTOP capacitor will couple more ripple into FB to help
eliminate the problem. An optional connection on the PCB
should be available for this capacitor.
ESR loop instability is caused by insufficient ESR. The
details of this stability issue are discussed in the ESR
Requirements section. The best method for checking
stability is to apply a zero-to-full load transient and observe
the output voltage ripple envelope for overshoot and ringing.
Ringing for more than one cycle after the initial step is an
indication that the ESR should be increased.
One simple way to solve this problem is to add trace
resistance in the high current output path. A side effect of
adding trace resistance is output decreased load regulation.
ESR Requirements
A minimum ESR is required for two reasons. One reason is
to generate enough output ripple voltage to provide10 mVp-p
at the FB pin (after the resistor divider) to avoid doublepulsing.
The second reason is to prevent instability due to insufficient
ESR. The on-time control regulates the valley of the output
ripple voltage. This ripple voltage is the sum of the two
voltages. One is the ripple generated by the ESR, the other
is the ripple due to capacitive charging and discharging
during the switching cycle. For most applications the
minimum ESR ripple voltage is dominated by the output
capacitors, typically SP or POSCAP devices. For stability the
ESR zero of the output capacitor should be lower than
approximately one-third the switching frequency. The
formula for minimum ESR is shown by the following
equation.
ESRMIN =
3
2 x π x COUT x fSW
For applications using ceramic output capacitors, the ESR is
normally too small to meet the above ESR criteria. In these
applications it is necessary to add a small virtual ESR
network composed of two capacitors and one resistor, as
shown in figure 14. This network creates a ramp voltage
Document Number: 69062
S10-1367-Rev. D, 14-Jun-10
SiC417
Vishay Siliconix
across CL, analogous to the ramp voltage generated across
the ESR of a standard capacitor. This ramp is then
capacitive-coupled into the FB pin via capacitor CC.
L
Highside
CL
RL
R1
Lowside
CC
COUT
R2
FB
pin
Figure 14 - Virtual ESR Ramp Current
Dropout Performance
The output voltage adjusts range for continuous-conduction
operation is limited by the fixed 250 ns (typical) minimum
off-time of the one-shot. When working with low input
voltages, the duty-factor limit must be calculated using
worst-case values for on and off times. The duty-factor
limitation is shown by the next equation.
DUTY =
TON(MIN)
TON(MIN) x TOFF(MAX)
The inductor resistance and MOSFET on-state voltage drops
must be included when performing worst-case dropout
duty-factor calculations.
This trace resistance should be optimized so that at full load
the output droops to near the lower regulation limit. Passive
droop minimizes the required output capacitance because
the voltage excursions due to load steps are reduced as
seen at the load.
The use of 1 % feedback resistors contributes up to 1 %
error. If tighter DC accuracy is required, 0.1 % resistors
should be used.
The output inductor value may change with current. This will
change the output ripple and therefore will have a minor
effect on the DC output voltage. The output ESR also affects
the output ripple and thus has a minor effect on the DC
output voltage.
Switching Frequency Variations
The switching frequency will vary depending on line and load
conditions. The line variations are a result of fixed
propagation delays in the on-time one-shot, as well as
unavoidable delays in the external MOSFET switching. As
VIN increases, these factors make the actual DH on-time
slightly longer than the ideal on-time. The net effect is that
frequency tends to falls slightly with increasing input voltage.
The switching frequency also varies with load current as a
result of the power losses in the MOSFETs and the inductor.
For a conventional PWM constant-frequency converter, as
load increases the duty cycle also increases slightly to
compensate for IR and switching losses in the MOSFETs
and inductor.
A constant on-time converter must also compensate for the
same losses by increasing the effective duty cycle (more
time is spent drawing energy from VIN as losses increase).
The on-time is essentially constant for a given VOUT/VIN
combination, to off set the losses the off-time will tend to
reduce slightly as load increases. The net effect is that
switching frequency increases slightly with increasing load.
System DC Accuracy (VOUT Controller)
Three factors affect VOUT accuracy: the trip point of the FB
error comparator, the ripple voltage variation with line and
load, and the external resistor tolerance. The error
comparator off set is trimmed so that under static conditions
it trips when the feedback pin is 500 mV, 1 %.
The on-time pulse from the SiC417 in the design example is
calculated to give a pseudo-fixed frequency of 250 kHz.
Some frequency variation with line and load is expected.
This variation changes the output ripple voltage. Because
constant on-time converters regulate to the valley of the
output ripple, ½ of the output ripple appears as a DC
regulation error. For example, if the output ripple is 50 mV
with VIN = 6 V, then the measured DC output will be 25 mV
above the comparator trip point. If the ripple increases to
80 mV with VIN = 25 V, then the measured DC output will be
40 mV above the comparator trip. The best way to minimize
this effect is to minimize the output ripple.
To compensate for valley regulation, it may be desirable to
use passive droop. Take the feedback directly from the
output side of the inductor and place a small amount of trace
resistance between the inductor and output capacitor.
Document Number: 69062
S10-1367-Rev. D, 14-Jun-10
www.vishay.com
15
V5V
P3
V5V
B2
V IN_GND
B1
V IN
1
1
1
1
C26
4.7 µF
1
M1
1
J7
Probe Test Pin
5
C12
150 µF
+
P1
VIN
C27
4.7 µF *
C8
10 µF
5
2
4
3
1
1
M2
1
P4
VLDO
1
M3
1
1
R29
10K
1
M4
2
7
3
6
9
10
11
34
R6 100K
ENL
P6
C13
0.01 µF
R12
57.6K
C11
0.1 µF
R2
300K *
C29
22 µF
0
C10
10 µF
C28 R11
0.1 µF
C9
10 µF
V IN
J4
Probe Test Pin
EN_PSV
1
5
1
FBL
VLDO
V5V
VIN
VIN
VIN
VIN
VIN
32
ENL
R1
300K *
29
EN/PSV
P5
14
U1
SiC417
DL
5
R39 0R
27
1
28
25
24
23
13
33
C32 1n
26
PGD 31
TON
ILIM
FB
LX
LX
LX
LX
LX
LX
R7 0
R30
75K
C30
47 pF
R40
1Ω
R15 10K
R8
10K
C6
0.1 µF
J3
Probe Test Pin
C5
0.1 µF
5
J2
Probe Test Pin
3
4
2
BST
P2
V IN_GND
1
1
3
4
2
12
DH
3
4
2
1
8
PGND
PGND
PGND
PGND
PGND
PGND
PGND
PGND
AGND
AGND
AGND
17
18
19
20
21
22
16
15
35
4
30
3
4
2
1
V5V
1
5
VOUT
1
L1
C24
10n *
P7
C14
0.1 µF
1
C19 1µ *
1 µH
J5
Probe Test Pin
R13 1K
R9 *
5
R3 1K
P8
1
V5V
P GOOD
C15
10 µF
1R01
1
Q1
Si4812BDY
C7
0.1 µF
R5
100K
+
+
+
+
C1
22 µF
C31
100 pF *
C25
68 pF
C20 C21 C22
C18
C16
C23
C17
10 µF 10 µF 10 µF 220 µF 220 µF 220 µF 220 µF
P12
LDTRG
R4
Step_I_Sense
C2
22 µF
R23
7.15K
R10
10K
5
C3
22 µF
1
P11
VO_GND
VCTRL
P9
P10
VO
1
J6
Probe Test Pin
Vo
C4
22 µF
2
4
3
1
www.vishay.com
16
1
J1
3 Probe Test Pin
4
1
2
B4
VO
V O_GND
1
1
B3
SiC417
Vishay Siliconix
SiC417 EVALUATION BOARD SCHEMATIC
Figure 15. Evaluation Board Schematic
Document Number: 69062
S10-1367-Rev. D, 14-Jun-10
SiC417
Vishay Siliconix
BILL OF MATERIALS
Reference Designator
Value
Voltage
B1, B2, B3, B4
Footprint
Part Number
Manufacturer
SOLDER-BANANA
575-4
Keystone
C29
22 µF
16 V
SM/C_1210
GRM32ER71C226ME18L
Murata
C5
0.1 µF
10 V
SM/C_0402
C0402C104K8RAC7867
Vishay
C6
0.1 µF
10 V
SM/C_0805
C0402C104K8RAC7867
Vishay
C11, C14, C28
0.1 µF
50 V
SM/C_0603
VJ0603Y104KXACW1BC
Vishay
C8, C9, C10
10 µF
25 V
SM/C_1210
TMK325B7106MN-T
Taiyo Yuden
C12
150 µF
35 V
D8X11.5-D0.6X3.5
EEU-FM1V151
Panasonic
C13
0.01 µF
50 V
SM/C_0402
VJ0402Y103KXACW1BC
Vishay
C15, C20, C21, C22
10 µF
16 V
SM/C_1206
GRM31CR71C106KAC7L
C16, C17, C18, C23
220 µF
10 V
595D-D
593D227X0010E2TE3
C19
1 µF
Vishay
SM/C_0603
C24
10 nF
C25
100 pF
50 V
SM/C_0402
VJ0402A101JXACW1BC
Vishay
C26
4.7 µF
10 V
SM/C_0805
LMK212B7475KG-T
Taiyo Yuden
C27
4.7 µF
10 V
SM/C_0805
LMK212B7475KG-T
Taiyo Yuden
C30
47 pF
SM/C_0402
VJ0402A470JXACW1BC
SM/C_0402
VJ0402Y101KXQCW1BC
Vishay
SM/C_0805
VJ0805A102KXA
Vishay
Lecroy Probe Pin
PK007-015
Lecroy
C31
100 pF
C32
1000 pF
J1, J2, J3, J4, J5, J6, J7
Probe test
pin
SM/C_0603
50 V
L1
1 µH
IHLP4040
IHLP4040DZER1R0M01
Vishay
M1, M2, M3, M4
M HOLE2
Stacking Spacer
8834
Keystone
P1, P2, P3, P4, P5, P6, P7,
P8, P9, P10, P11, P12
VIN, GND
etc.
Probe Hook
1540-2
Keystone
R1
300K
50 V
SM/C_0603
CRCW060310K0FKEA
Vishay
R2
300K
50 V
SM/C_0603
CRCW06030000FKEA
Vishay
SM/C_0402
CRCW04021K00FKED
Vishay
50 V
SM/C_0603
CRCW0603100KFKEA
Vishay
R3, R13
1K
R6
100K
R7, R11
0R
SM/C_0603
CRCW06030000Z0EA
Vishay
R8, R10, R15, R29
10K
SM/C_0603
MCR03EZHF1002
ROHM
R9
SM/C_0603
R12
57.6K
SM/C_0603
CRCW060357K6FKEA
Vishay
R23
7.15K
SM/C_0603
CRCW06037K15FKEA
Vishay
R30
75K
SM/C_0603
CRCW0603154KFKEA
Vishay
R39
0R
SM/C_0402
CRCW04020000Z0ED
Vishay
CRCW08051R00FNEA
R40
1Ω
SM/C_0805
U1
SiC417
QFN5X5_32 leads + 3 pads
Vishay
Vishay
Optional Cicuitry for Transient Response Testing
Q1
Si4812BDY
30 V
SO-8
Si4812BDY
Vishay
R4
1R01
200 V
C_2512
CRCW25121R00FKTA
Vishay
R5
100K
50 V
SM/C_0603
CRCW0603100KFKEA
Vishay
C7
0.1 µF
50 V
SM/C_0603
VJ0603Y104KXACW1BC
Vishay
C1, C2, C3, C4
22 µF
16 V
SM/C_1210
GRM32ER71C226ME18L
Murata
Document Number: 69062
S10-1367-Rev. D, 14-Jun-10
www.vishay.com
17
SiC417
Vishay Siliconix
PCB LAYOUT OF THE EVALUATION BOARD
www.vishay.com
18
Figure 16. PCB Layout - Top Layer
Figure 17. PCB Layout - MidLayer1
Figure 18. PCB Layout - MidLayer2
Figure 19. PCB Layout - Bottom Layer
Document Number: 69062
S10-1367-Rev. D, 14-Jun-10
SiC417
Vishay Siliconix
PACKAGE DIMENSIONS AND MARKING INFO
5.000 ± 0.075
A
+
5.000 ± 0.075
Pin # 1 (Laser Marked)
Top View
B
0.10 C
0.08 C
C
0.900 ± 0.100
0.050
0.000
0.460
Bare
Copper
16
CL
9
17
8
3.480 ± 0.100
CL
0.460
Bottom View
R Full
0.250 ± 0.050
0.10
C AB
1.485 ± 0.100
0.200 ref.
1.970 ± 0.100
24
25
32
R0.200
Pin 1 I.D.
1.660 ± 0.100
0.500
0.400 ± 0.100
1.050 ± 0.100
Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon
Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and
reliability data, see www.vishay.com/ppg?69062.
Document Number: 69062
S10-1367-Rev. D, 14-Jun-10
www.vishay.com
19
Package Information
Vishay Siliconix
PowerPAK® MLP55-32L CASE OUTLINE
0.08 C
A
A1
D
A2
25
1
4
(5 mm x 5 mm)
Pin #1 identification
R0.200
E2 - 3
0.10
E
32L T/SLP
D2 - 2
32
24
E2 - 1
CAB
e
0.10 CB
D2 - 1
0.360
8
17
B
b
16
L
C
0.36
Top View
(Nd-1) Xe
Ref.
0.10 CA
A
E2 - 2
2x
0.45
5 6
Pin 1 dot
by marking
2x
Side View
D2 - 3
D2 - 4
(Nd-1) Xe
Ref.
D4
9
Bottom View
MILLIMETERS
INCHES
DIM
MIN.
NOM.
MAX.
MIN.
NOM.
A
0.80
0.85
0.90
0.031
0.033
0.035
A1(8)
0.00
-
0.05
0.000
-
0.002
0.30
0.078
A2
b(4)
0.20 REF.
0.20
0.25
0.008 REF.
0.098
D
5.00 BSC
0.196 BSC
e
0.50 BSC
0.019 BSC
E
5.00 BSC
L
0.35
0.40
MAX.
0.011
0.196 BSC
0.45
0.013
0.015
N(3)
32
32
Nd(3)
8
8
Ne(3)
8
0.017
8
D2 - 1
3.43
3.48
3.53
0.135
0.137
0.139
D2 - 2
1.00
1.05
1.10
0.039
0.041
0.043
D2 - 3
1.00
1.05
1.10
0.039
0.041
0.043
D2 - 4
1.92
1.97
2.02
0.075
0.077
0.079
E2 - 1
3.43
3.48
3.53
0.135
0.137
0.139
E2 - 2
1.61
1.66
1.71
0.063
0.065
0.067
E2 - 3
1.43
1.48
1.53
0.056
0.058
0.060
ECN: T-08957-Rev. A, 29-Dec-08
DWG: 5983
Notes
1. Use millimeters as the primary measurement.
2. Dimensioning and tolerances conform to ASME Y14.5M. - 1994.
3. N is the number of terminals.
Nd is the number of terminals in X-direction and Ne is the number of terminals in Y-direction.
4. Dimension b applies to plated terminal and is measured between 0.20 mm and 0.25 mm from terminal tip.
5. The pin #1 identifier must be existed on the top surface of the package by using indentation mark or other feature of package body.
6. Exact shape and size of this feature is optional.
7. Package warpage max. 0.08 mm.
8. Applied only for terminals.
Document Number: 64714
Revision: 29-Dec-08
www.vishay.com
1
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000