NOT RECOMMENDED FOR NEW DESIGN SC619 Charge Pump Flash LED Driver with Safety Timer POWER MANAGEMENT Features Description The SC619 is a high-current charge pump designed specifically for use with white LEDs used in camera flash applications. Only two small bucket capacitors are required to develop the output drive, providing a low EMI solution compared to inductive boost regulators. Flash and spotlight — two selectable modes Flash mode — up to 700mA output Flash mode — 500mA max output (over rated voltage, temperature, and load conditions) Flash mode safety timer shut-off — 1 second Spotlight mode set to 20% of flash current Spotlight mode — up to 140mA output Spotlight mode —1x mode (under most conditions) for best efficiency Input range — 3.0V to 5.25V External flash control pin for synchronization to a camera module or graphics controller Short-circuit, over-voltage, and over-temperature protection Soft-start functionality Separate flash and spotlight control inputs for maximum versatility Ultra-thin package MLPD-UT-10 — 3mm x 3mm x 0.6mm Applications The SC619 has two modes of operation: flash mode and spotlight mode. In flash mode, the SC619 is capable of delivering 500mA of regulated current for a duration of 500ms or up to 700mA for a reduced duration. A safety timer is also included to ensure the LED cannot be left on indefinitely and overheat. In spotlight mode the SC619 outputs 20% of the flash mode current and can remain enabled continuously. N O FO T R R EC N O EW M M D EN ES D IG ED N An external resistor is connected in series with the LED to set the current. In flash mode, this resistor can dissipate up to 175mW, reducing the power dissipation requirement of the SC619. The flash input overrides the control input to make sure the flash function is activated . The SC619 ultra-thin package provides both a low profile and high thermal efficiency. Mobile camera phones Digital cameras PDAs with built-in cameras Typical Application Circuit SC619 VBAT VIN VOUT C1+ GND C1- ISET C2+ CTRL C2- FLASH 10μF 1μF 1μF 1μF White LED RSET FLASH CTRL February 8, 2008 1 NOT RECOMMENDED FOR NEW DESIGN Pin Configuration Ordering Information 10 C2+ 9 VOUT 3 8 C1+ C1- 4 7 CTRL FLASH 5 6 ISET 1 C2- 2 GND TOP VIEW Device Package SC619ULTRT(1)(2) MLPD-UT-10 3×3 SC619EVB Evaluation Board Notes: (1) Available in tape and reel only. A reel contains 3,000 devices. (2) Lead-free package only. Device is WEEE and RoHS compliant. N O FO T R R EC N O EW M M D EN ES D IG ED N VIN SC619 T MLPD-UT-10; 3x3, 10 LEAD θJA = 40°C/W Marking Information 619 yyww xxxx yyww = Date code xxxx = Semtech Lot Number 2 NOT RECOMMENDED FOR NEW DESIGN SC619 Absolute Maximum Ratings Recommended Operating Conditions VIN (V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to +6.5 Ambient Temperature Range (°C) . . . . . . . . . . . . -40 to +85 VOUT (V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to +6.5 C1+, C2+ (V) . . . . . . . . . . . . . . . . . . . . . . . -0.3 to (VOUT + 0.3) Pin Voltage - All Other Pins (V) . . . . . . -0.3 to (VIN + 0.3) Thermal Information Circuit Duration . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous ESD Protection Level(1) (kV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Thermal Resistance, Junction to Ambient(2) (°C/W) . . . . 40 Junction Temperature Range (°C) . . . . . . . . . . . . -40 to +150 Storage Temperature Range (°C) . . . . . . . . . . . . . -60 to +150 N O FO T R R EC N O EW M M D EN ES D IG ED N Peak IR Reflow Temperature (10s to 30s) (°C) . . . . . . . +260 Exceeding the above specifications may result in permanent damage to the device or device malfunction. Operation outside of the parameters specified in the Electrical Characteristics section is not recommended. NOTES: (1) Tested according to JEDEC standard JESD22-A114-B. (2) Calculated from package in still air, mounted to 3” x 4.5”, 4 layer FR4 PCB with thermal vias under the exposed pad per JESD51 standards. Electrical Characteristics Unless otherwise specified: TA = 25°C for TYP, -40°C to +60°C for MIN and MAX; CBUCKET = COUT = 1.0μF (ESR < 0.1Ω); CIN = 10.0μF; VIN = 3.0V to 5.25V; VOUT = 2.8V to 4.25V; RSET = 0.5Ω (0.1%). Parameter Symbol Conditions Min FLASH high, RSET = 0.357Ω 3.7V < VIN < 4.2V, VOUT = 3.7V(1) Output Current ISET Reference Voltage Quiescent Current IOUT VISET IQ FLASH high, RSET = 0.5Ω 3.3V < VIN < 4.2V 2.8V < VOUT < 4.25V Typ Max Units 700 460 500 540 mA FLASH low, CTRL high, RSET = 0.357Ω 3.7V < VIN < 4.2V, VOUT = 3.4V(1) 140 FLASH low, CTRL high, RSET = 0.5Ω 3.0V < VIN < 4.5V 2.8V < VOUT < 4.5V 75 100 125 FLASH high, RSET = 0.5Ω 3.3V < VIN < 4.2V 2.8V < VOUT < 4.25V 230 250 270 FLASH low, CTRL high, RSET = 0.5Ω 3.0V < VIN < 4.5V 2.8V < VOUT < 4.5V 37.5 mV 50 62.5 FLASH high 3.4 5.0 mA FLASH low, CTRL high 2.0 4.5 mA FLASH low, CTRL low 0.1 2.0 μA 3 NOT RECOMMENDED FOR NEW DESIGN SC619 Electrical Characteristics (continued) Symbol Conditions Max Units Flash Mode Pulse Duration(2) tFLASH 3.3V < VIN < 4.2V IOUT = 500mA, VOUT > 2.8V 500 ms Flash Mode Start-Up Time(2) tF-SU t = 0 when FLASH goes high to IOUT = 90% of final value 1 ms Flash Mode Safety Timer(2) tSAFE FLASH high 1.25 s Spotlight Mode Start-Up Time(2,3) tS-SU VIN = 4.2V, VOUT = 3.2V; t = 0 when CTRL goes high to IOUT = 90% of final value 1 ms Oscillator Frequency fOSC Device enabled N O FO T R R EC N O EW M M D EN ES D IG ED N Parameter Oscillator Frequency Accuracy Short-Circuit Output Current Limit Input Current Limit ΔfOSC ISC Min Typ 0.90 250 -15 kHz 15 % Steady State with VOUT shorted to GND 600 mA 2x mode, 3.3V < VIN < 4.2V 2.1 A ILIMIT 2x mode, VIN = 3.7V, VOUT = 3.7V, TA = 25°C 1.38 TOT Rising threshold 150 TOT -HYS Hysteresis 10 Logic Input High Threshold VIH FLASH, CTRL 1.5 Logic Input Low Threshold VIL FLASH, CTRL Logic Input High Current IIH 1.53 Over-Temperature Protection(2) Logic Input Low Current ISET Ripple Voltage IIL °C V 0.4 FLASH 1 20 35 CTRL 2 40 70 FLASH, CTRL 0.1 2.0 Spotlight mode — IOUT = 100mA 25 FLASH mode — IOUT = 500mA 100 V μA VISET(P-P) μA mV Notes: 1) VOUT required by the typical LED at this current. 2) Guaranteed by design - not tested in production. 3) If conditions force 2x mode operation, this start-up time will increase by approximately 32ms due to the timer that is enabled to ensure 2x mode is needed. 4 NOT RECOMMENDED FOR NEW DESIGN SC619 Typical Characteristics Flash Current at 100ms, RISET = 500mΩ, VOUT = 3.68V 515 515 510 510 505 505 LED Current (mA) LED Current (mA) Flash Current at 10ms, RISET = 500mΩ, VOUT = 3.75V 500 495 490 500 495 485 3.3 3.45 N O FO T R R EC N O EW M M D EN ES D IG ED N 490 3.6 3.75 3.9 4.05 485 3.3 4.2 3.45 3.75 VIN (V) 3.6 VIN (V) 112.0 505 LED Current (mA) LED Current (mA) 4.2 120.0 510 500 495 104.0 96.0 88.0 490 485 3.3 3.45 3.6 3.75 3.9 4.05 80.0 3.00 4.2 3.45 VIN (V) Flash Duration, RISET = 350mΩ, VOUT = 3.86V (start), 3.61V (LED Heated 500ms) 3.90 4.35 4.80 5.25 VIN (V) Flash Duration, RISET = 500mΩ, VOUT = 3.75V (start), 3.58V (LED Heated 500ms) 515 755 509 735 VIN=4.2V LED Current (mA) LED Current (mA) 4.05 Spotlight Current, RISET = 500mΩ, VOUT = 2.93V Flash Current at 500ms, RISET = 500mΩ, VOUT = 3.58V 515 3.9 VIN=3.7V 715 VIN=4.2V VIN=3.7V 503 VIN=3.3V 497 VIN=3.4V 695 491 VIN=3.3V 675 485 0 100 200 300 Pulse Duration (ms) 400 500 0 100 200 300 Pulse Duration (ms) 400 500 5 NOT RECOMMENDED FOR NEW DESIGN SC619 Typical Characteristics (continued) Flash Mode Ripple, RISET = 500mΩ Start-Up Flash Mode, 500mA Ch 1: 100mV/DIV Ch 2: 200mV/DIV Ch 2: 2V/DIV N O FO T R R EC N O EW M M D EN ES D IG ED N Ch 1: 100mV/DIV Ch 3: 2V/DIV Ch 3: 200mV/DIV Time (4μs/div) Safety Timer Shut-Off Time (40μs/div) Spotlight 1x Mode Ripple, RISET = 500mΩ Ch1: 100mV/DIV Ch1: 50mV/DIV Ch2: 2V/DIV Ch2: 50mV/DIV Ch3: 5V/DIV Ch3: 50mV/DIV Time (200ms/div) Time (4μs/div) Spotlight 2x Mode Ripple, RISET = 500mΩ Short Circuit Current Limiting, VIN = 5.25V, VOUT = 0V Ch1: 50 mV/DIV Ch2: 100 mV/DIV Ch1: 2V/DIV Ch3: 100 mV/DIV Ch4: 100mA/DIV Time (4μs/div) Time (400ms/div) 6 NOT RECOMMENDED FOR NEW DESIGN SC619 Pin Descriptions Pin# Pin Name Pin Function 1 VIN Input voltage 2 C2- Negative terminal of bucket capacitor 2 3 GND Ground— connect to ground plane using multiple vias 4 C1- Negative terminal of bucket capacitor 1 5 FLASH 6 ISET 7 CTRL 8 C1+ 9 VOUT 10 C2+ T Thermal Pad Flash mode enable pin— puts the device in active flash mode when high and also overrides CTRL. N O FO T R R EC N O EW M M D EN ES D IG ED N Current-setting reference pin — connect to the LED cathode and the current setting resistor. Control input bit — used to enable and set the output current in spotlight mode when high. Positive terminal of bucket capacitor 1 Output pin — connect to the LED anode Positive terminal of bucket capacitor 2 Pad for heat sinking purposes — not connected internally. Connect to ground plane using multiple vias. 7 NOT RECOMMENDED FOR NEW DESIGN SC619 Block Diagram VIN 1 LDO N O FO T R R EC N O EW M M D EN ES D IG ED N 250kHz CTRL 7 FLASH 5 Logic Control and Flash Mode Timer Reference Voltage Generator CHARGE PUMP 8 C1+ 4 C1- 10 C2+ 2 C2- 9 VOUT 3 GND 6 ISET 8 NOT RECOMMENDED FOR NEW DESIGN SC619 Applications Information The SC619 is a powerful dual-mode charge pump designed to drive a high-intensity white LED. A constant current spotlight mode or a pulsed current with higher intensity is used for camera flash. The device operates in 2x mode while operating in flash mode. In spotlight mode it can operate in either 2x or 1x mode depending on the load current, load voltage, and input voltage levels. 800 700 600 500 400 300 N O FO T R R EC N O EW M M D EN ES D IG ED N In flash mode the SC619 output can drive 500mA at 4.25V into an LED for a minimum duration of 500ms under all temperature and input conditions. The FLASH pin is used to trigger this mode (active high). In spotlight mode the SC619 regulates the output current to 20% of the flash mode current setting, when the CTRL pin is pulled high and the FLASH pin is low. Flash mode has priority over spotlight mode, i.e., the FLASH pin triggers flash mode regardless of the state of the CTRL pin. example, 700mA derates to a maximum of 350ms. In flash mode, IOUT = 250mV/RISET. Figure 1 shows maximum flash mode current for extended duration times. Flash Current [mA] General Operation Output current is regulated by attaching the ISET pin to the cathode(s) of the LED package and a low resistance sense resistor (typically 0.5Ω). The ISET pin monitors the voltage at the cathode and signals the charge pump to increase or decrease the output current until the ISET voltage reaches the programmed setting. The resistor value is chosen to set the current through the LED based on this reference voltage. The resistor can be chosen to set either the flash mode current or spotlight mode current, but it should not be less than 0.35Ω due to output current limitations of the device. Flash Mode Flash mode is enabled whenever the FLASH pin is pulled high and remains active until the FLASH pin is released. This mode has higher priority than spotlight mode, so the state of the CTRL pin is overridden whenever the FLASH pin is activated. While in flash mode the reference voltage on the ISET pin is set to 250mV. The duration of the pulse is limited by the amount of power that can be dissipated in the SC619 before it exceeds the maximum operating temperature. If an output current less than the rated 500mA is desired, the duration of the pulse can increase proportionally. Extending flash mode beyond the 500ms pulse limit could adversely affect the long term reliability of the SC619. Flash duration must be derated at higher currents. For 200 100 0 0 100 200 300 400 500 600 700 800 900 1000 Flash Duration [ms] Figure 1 — Maximum Flash Duration Flash Mode Safety Timer The SC619 provides a time-out protection function when in flash mode. The output is disabled if the FLASH pin is held high for longer than 1 second to protect the LED. Once this time-out has occurred, the output will stay disabled until the FLASH pin has been pulled low and then re-enabled. Spotlight Mode Spotlight mode is enabled by setting the CTRL pin high and keeping the FLASH pin low. When in spotlight mode, the SC619 can maintain a constant current indefinitely to drive an LED or bank of LEDs. The ISET reference voltage is set to 50mV so that the output current is maintained at 100mA when a 0.5Ω resistor is used. Spotlight current is always 20% of flash current for any given value of RISET. In spotlight mode, IOUT = 50mV/RISET. To maximize power efficiency, the SC619 has been designed to operate in 1x mode when conditions do not require the charge pump to be active. When first enabled the SC619 attempts to regulate the voltage on the ISET pin in 1x mode. If the voltage on the ISET pin cannot be maintained and this condition persists for longer than 32ms, then the charge pump will change to 2x mode operation. In a typical application, the SC619 will operate in 1x mode until the supply voltage decreases sufficiently 9 NOT RECOMMENDED FOR NEW DESIGN SC619 Applications Information (continued) that the voltage on the ISET pin can no longer be maintained. After a 32ms delay (included to prevent false transitions) the charge pump will convert to 2x mode. After the charge pump switches from 1x mode to 2x mode, the device remains in 2x mode until the part is turned off. If the part is re-enabled in spotlight mode, it will begin operation in 1x mode and determine the appropriate mode of operation as previously described. Over-Current Protection When the SC619 is in 2x mode, the input current will be approximately double the required output. When the steady-state load requires the maximum current available in 2x mode, the OCP circuit prevents the device from overheating from excessive power dissipation. This feature protects the device when in 1x mode. The current limit is set lower in the 1x mode due to lower current requirements. Protection Circuitry • • • • • Short-Circuit Current Protection SSCP is provided to limit the current that can be sourced when the output is shorted to ground. When a short circuit forces VOUT to drop below 2V, the SCCP detects the condition and limits the output current. N O FO T R R EC N O EW M M D EN ES D IG ED N The SC619 provides several protection features to safeguard the device from catastrophic failures. These features include: Input Over-Voltage Protection (IOVP) Output Over-Voltage Protection (OVP) Over-Temperature Protection (OTP) Over-Current Protection (OCP) Short-Circuit Current Protection (SCCP) Input Over-Voltage Protection IOVP is included to prevent operation at high input voltages that could damage the device. The IOVP circuit senses the input voltage and determines when the supply exceeds 6V. Hysteresis is included in this circuit to avoid chattering between states. When the voltage rises above this threshold, the device is disabled until the input voltage drops to a level within the specified range. Output Over-Voltage Protection Output OVP prevents the SC619 from generating an output voltage that could damage other devices connected to it such as load LEDs and bypass capacitors. When the output voltage exceeds 5.5V, the OVP circuit disables the charge pump until the voltage decreases to a level within the acceptable range. This circuit allows the device to drive LEDs with high forward voltages at a reduced level without exceeding the output voltage limits specified for the device. Over-Temperature Protection The OTP circuit prevents the device from overheating and experiencing a catastrophic failure. When the junction temperature exceeds 150°C the device is disabled. It remains disabled until the junction temperature drops below this threshold. Hysteresis is included to prevent toggling between modes. Resistor Selection The ISET resistor selection is critical in generating the correct current. The value can be chosen to set the spotlight mode current or the flash mode current, and the two current settings are dependent on the same resistor. It is recommended that the resistor be selected to match the desired LED current for flash mode. This allows the designer to set the SC619’s maximum current and select the resistor package size necessary for the power dissipation required in flash mode. The typical application uses a 0.5Ω resistor to set a flash mode current of 500mA and spotlight mode current of 100mA. A high precision resistor should be used to ensure the specified accuracy for LED current. To avoid malfunction of the charge pump, it is recommended that the resistance seen at the ISET pin remain constant while the device is active (flash or spotlight mode). Changing the resistance value or the load current while the device is active could cause instability. Capacitor Selection The SC619 is designed to use low-ESR ceramic capacitors for the input and output bypass capacitors as well as the charge pump bucket capacitors. Ideal performance is achieved when C1 is exactly equal to C2. It is recommended that X5R or X7R ceramic capacitors be used for best performance. 10 NOT RECOMMENDED FOR NEW DESIGN SC619 Applications Information (continued) PCB Layout Considerations The following layout is suggested for a two-layer design. The capacitors C1 and C2 are the bucket capacitors and each conducts the full load current of up to 500mA pulsed for one half clock cycle. C3 is the output decoupling capacitor placed near the VOUT pin. C4 is the input decoupling capacitor placed near the VIN pin. Multiple vias should be used whenever it is necessary to change layers on nets connecting to pins VIN, VOUT, GND, C1-, C1+, C2- and C2+. while in flash or spotlight mode. It is critical to maintain adequate ground plane around the device to maximize heat transfer and avoid over-temperature shutdown. N O FO T R R EC N O EW M M D EN ES D IG ED N The load current return path is from the ISET sense point through the resistor and back to the ground pins. Resistance in this path adds to the total resistance and has the effect of reducing the LED current by about 4% per 10mV of DC drop across the return copper trace in flash mode. For this reason, it is crucial to have a low resistance return path. Place and ground the resistor as close as possible to the ground pin of the SC619. The trace from the ISET pin has virtually no current. The ISET trace should make contact at the pad of the power sense resistor to minimize the effect of voltage drop between the LED cathode and the resistor. Resistor R1 is routed with a very low resistance connection between R1 and GND pin 3. The sense trace between Pin 6 and R1 is routed around the ground vias, allowing the shortest ground return path possible. The sense trace is connected to R1 at the positive terminal pad for the most accurate output possible. The bottom copper layer is mostly a ground plane with no obstructions between the ground vias. The smaller rectangle to the left connects the input power to VIN pin 1 and input capacitor C4. The two traces at the lower left are for logic inputs FLASH and CTRL. The trace to the right is the ISET pin sense trace. The sense trace is routed out of the path of the returning ground current. Thermal Resistance Considerations The SC619 package is thermally efficient when the circuit board layout connects the thermal pad through multiple vias to the ground plane. The thermal resistance is rated at 40°C/W, and this rating is dependent on the connection between the thermal pad and the ground plane. The layout should keep the junction temperature below the OTP limit while operating the SC619 within the specified electrical conditions for IOUT and VISET. A poor layout may allow the junction temperature to reach the OTP limit 11 NOT RECOMMENDED FOR NEW DESIGN SC619 Outline Drawing — MLPD-UT-10 E A DIMENSIONS B DIM INCHES MIN A .018 NOM - A1 .000 - MILLIMETERS MAX MIN .024 0.45 .002 0.00 (.006) A2 NOM - MAX 0.60 0.05 (0.1524) b .007 .009 .011 0.18 0.23 0.30 C .074 .079 .083 1.87 2.02 2.12 PIN 1 D .042 .048 .052 1.06 1.21 1.31 INDICATOR E e .114 .118 .122 2.90 3.00 3.10 L .012 .020 0.30 E (LASER MARK) bbb A aaa .016 0.50 BSC 0.40 10 10 .003 0.08 N O FO T R R EC N O EW M M D EN ES D IG ED N N aaa .020 BSC .004 0.50 0.10 SEATING PLANE C A1 C 1 C A2 2 LxN D N e bxN bbb NOTES: C A B 1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). 2. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS TERMINALS. 12 NOT RECOMMENDED FOR NEW DESIGN SC619 Land Pattern — MLPD-UT-10 DIMENSIONS K DIM (C) G H Z X MILLIMETERS C (.112) (2.85) G .075 1.90 H .055 1.40 K .087 2.20 P .020 0.50 X .012 0.30 N O FO T R R EC N O EW M M D EN ES D IG ED N Y INCHES Y .037 0.95 Z .150 3.80 P NOTES: 1. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY. CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR COMPANY'S MANUFACTURING GUIDELINES ARE MET. 2. THERMAL VIAS IN THE LAND PATTERN OF THE EXPOSED PAD SHALL BE CONNECTED TO A SYSTEM GROUND PLANE. FAILURE TO DO SO MAY COMPROMISE THE THERMAL AND/OR FUNCTIONAL PERFORMANCE OF THE DEVICE. Contact Information Semtech Corporation Power Management Products Division 200 Flynn Road, Camarillo, CA 93012 Phone: (805) 498-2111 Fax: (805) 498-3804 www.semtech.com 13