Owner's Manual for DDR1327S 933320 (English)

Owner’s Manual
Full Motion
Flat Screen Desk Mount
MODEL: DDR1327S
CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR
PROPERTY DAMAGE MAY OCCUR!
75x75
100x100
27”
MAX
9kg
(19.8lbs)
MAX
Este manual esta disponible en español en la página de Tripp Lite: www.tripplite.com
Ce manuel est disponible en français sur le site Web de Tripp Lite : www.tripplite.com
Русскоязычная версия настоящего руководства представлена на веб-сайте компании
Tripp Lite по адресу: www.tripplite.com
Dieses Handbuch ist in deutscher Sprache auf der Tripp Lite-Website verfügbar: www.tripplite.com
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2014 Tripp Lite. All rights reserved.
1
14-04-240-933320-EN.indd 1
4/29/2014 2:26:03 PM
NOTE: Read the entire instruction manual before you start installation and assembly.
WARNING
• Do not begin the installation until you have read and understood the instructions
and warnings contained in this manual. If you have any questions regarding any
of the instructions or warnings, please visit www.tripplite.com/support.
• This mounting bracket was designed to be installed and utilized ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• Make sure that the mounting surface can safely support the combined load of
the equipment and all attached hardware and components.
• Always use an assistant or mechanical lifting equipment to safely lift and position
equipment.
• Tighten screws firmly, but do not over-tighten. Over-tightening can damage the
items, greatly reducing their holding power.
• This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
Warranty & Warranty Registration
5-Year Limited Warranty
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects
in material and workmanship for a period of 5 years from the date of initial purchase. If the product should
prove defective in material or workmanship within that period, Seller will repair or replace the product, in its sole
discretion.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE,
ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY
SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES,
INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY
PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL
DAMAGES. (Some states do not allow limitations on how long an implied warranty lasts, and some states do not
allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions
may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from
jurisdiction to jurisdiction).
WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate
or safe for the use intended. Since individual applications are subject to great variation, the manufacturer makes
no representation or warranty as to the suitability or fitness of these devices for any specific application.
WARRANTY REGISTRATION
Visit www.tripplite.com/warranty today to register the warranty for your new Tripp Lite product. You’ll be
automatically entered into a drawing for a chance to win a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.
2
14-04-240-933320-EN.indd 2
4/29/2014 2:26:03 PM
Component Checklist
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to
installing. If any parts are missing or faulty, visit www.tripplite.com/support for service.
Adapter Bracket Assembly (x1)
Desk Clamp Assembly (x1)
Pole (x1)
Package M
M4X14 (x4)
M5X14 (x4)
D5 Washer (x4)
Package P
3mm Hex Key (x1)
6mm Hex Key (x1)
4mm Hex Key (x1)
5mm Hex Key (x1)
Base Plate (x1)
Pad (x1)
3
14-04-240-933320-EN.indd 3
4/29/2014 2:26:03 PM
1. Install the Pole and Desk Clamp Assembly
tighten
adjustable height
loosen
3mm Hex Key
collar
3mm Hex Key
3mm Hex Key
tighten
2. Desk Installation
2a. Edge Installation
Note: min. desktop thickness=10mm (.4”)
max. desktop thickness=90mm (3.5”)
tighten
• Determine approximate location for mount, keeping in mind display size, height adjustment and pitch/roll
requirements.
• Slip the desk mount assembly over the edge of desk so that clamp fully contacts desk edge.
• Turn the knob to adjust the clamp to edge of desk and secure it tightly.
4
14-04-240-933320-EN.indd 4
4/29/2014 2:26:03 PM
2. Desk Installation
2b. Hole Installation
Disassemble the desk clamp assembly by removing the clamp
adjustment screw and the three attachment screws from the
base plate.
Base Plate
Rubber Pad
Attachment Screw
4mm Hex Key
Re-install the base plate with three retained attachment screws. Tighten securely.
Note: min. hole diameter =10mm (.4”)
max. hole diameter =70mm (2.75”)
Pad
Clamp Adjustment Screw
From below the desk, insert retained clamp adjustment screw through Pad and up through the hole in the desk.
Thread screw by turning the knob into base plate but do not tighten completely at this time. Center the desk
mount assembly over the hole and then securely tighten screw.
5
14-04-240-933320-EN.indd 5
4/29/2014 2:26:03 PM
3. Install Adapter Bracket
Lift the display and align the rear mounting
holes with the mount’s VESA plate.
TV
TV
TV
D5 Washer M4X14
M5X14
Attach the display to the VESA plate with the appropriate included screws.
Do not over-tighten screws
6
14-04-240-933320-EN.indd 6
4/29/2014 2:26:04 PM
4. Install Adapter Bracket Assembly (attached display)
Using an assistant or mechanical
lifting equipment, lift the display with
attached VESA plate. Then slide the
adapter bracket assembly (with the
display attached) down the pole until it
touches the collar.
Collar
tighten
Adjustable Handle
Pulling up on the handle allows the
arm to rotate 360 degrees in either
direction. Releasing the handle enables
tightening or adjustment.
7
14-04-240-933320-EN.indd 7
4/29/2014 2:26:04 PM
5. Height Adjustment
6mm Hex Key
Tighten the socket
screw if the arm
assembly’s joints make
popping sounds during
adjustment.
Keep the wall mount arm level during tension adjustment. You may need to slightly loosen or tighten the
adjustment screw using the provided Hex Keys depending on the weight of display installed.
If display settles on its own, rotate adjustment screw towards the “+” symbol.
If display rises on its own, rotate adjustment screw towards the “-” symbol.
8
14-04-240-933320-EN.indd 8
4/29/2014 2:26:04 PM
6. Cable Management
FOLD 3
DUSTCATCHER
Connect the cables to the display. Press cable cover inward to route the cables through the space.
Note: Leave slack in cable for arm movement.
9
14-04-240-933320-EN.indd 9
4/29/2014 2:26:04 PM
7. Adjustment
To correct the tilting angle, tighten the
adjustment screws using the provided
Hex Keys (or tighten the knob).
+90°
-40°
5mm
Hex Key
360°
Max 335mm (13”)
Height Adjustment
360°
Adjust to the desired location or tilt.
Maintenance
• Check that the bracket is secure and safe to use at regular intervals (at least every three months).
• Please visit www.tripplite.com/support if you have any questions.
10
14-04-240-933320-EN.indd 10
4/29/2014 2:26:06 PM
11
14-04-240-933320-EN.indd 11
4/29/2014 2:26:06 PM
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
12
14-04-240-933320-EN.indd 12
14-04-240 93-3330_RevA
4/29/2014 2:26:08 PM