4 SPECIFICATION Schematic 4,7 3 4 0,7 3 2,3 3,8 1 500mOhm max. 1Ohm max. min. 100MOHM at 250VDC 250VAC for 1 minute 10ms MATERIAL >Actuator: >Base : >Frame : >Contact spring: >Terminal: LCP UL 94V-0 LCP UL 94V-0, color Black PA46 UL HB, color Black Stainless Steel with silver plating Copper Alloy with silver plating 2 ENVIRONMENTAL Storage condition : -40°C ~ +85°C . Operation condition : -40°C ~ +85°C Compliance : ROHS, Reach +0,1 -0,0 +0,1 -0,0 3,5 5,1 +0,2 -0,0 2,5 Total Travel Position (Measure Position) 3,3 1mA 5VDC SOLDERING INFORMATION >Terminal in SMD version >Reflow soldering according to JEDEC J-STD 020 Hot Air >Hand soldering under 350°C for 3sec. max P.C.B Mounting Plan 2,4 ±0,1 +0,0 -0,1 R Operating Direction 0,7 3 0,1 4,9 ±0,2 4,7 ±0,2 2 2 +0,5 0,7 2,4 3,2 -0,0 Switching on Position 1 1 >Rating: >Contact Resistance : Initial : After Life Test : >Insulation Resistance : >Dielectric Strength : >Bounce : 4 1,2 ±0,1 3,8 4,5 3 Scale - 5:1 HANDLING ADVISE >Set a delay time according to our definition bounce >Please operate the switch only in the direction , which is advise in our specification >Design the operation distance so, so that it can reach 3,2mm or lower at least. Recommend is to design the switch so, that the operation point can reach the total travel position >Protect the switch , do not overstress our parts. >For more information’s, please refer to our pre-caution guide PACKAGING INFORMATION >Tape & Reel Projection This electronic component is designed and developed with the intention for use in general electronics equipments. Before incorporating the components into any equipments in the field such as aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc. where higher safety and reliability are especially required or if there is possibility of direct damage or injury to human body, Wurth Elektronik must be asked for a written approval. In addition, even electronic component in general electronic equipments, when used in electrical circuits that require high safety, reliability functions or performance, the sufficient reliability evaluation-check for the safety must be performed before by the user before usage. Part number Force Schematic Life Cycle 461 011 220 101 60gf max SPST- NO 100.000 GENERAL TOLERANCE DIN ISO 2768 T1m Basic material Date 14-03-21 Name Fandrey DESCRIPTION Drawn Checked 14-03-21 Hsu 4.7x3.8mm Detect Switch, vertical right side, SMD version WS-DESV Scale a REV Operating Direction FILE 14-05-22 DaF DATE BY 5:1 Drawing.- No. Position SIZE 461011220101 A4 System: Solid Edge ST4 D0 B0 E2 W F E1 A K0 T P0 P2 W3 B top cover tape P1 C A N A W** close to center T1 T2 A0 D A0 tolerance size 6410xxxx B0 W P1 T T1 typ. typ. ±0,3 ±0,1 max. min. ref. typ. 5,00 5,60 16,00 12,00 0,35 0,10 5,25 4,80 END T2 K0 D0 E1 E2 F P0 P2 +0,1 ±0,1 min. 1,50 ±0,05 ±0,1 ±0,05 1,75 14,25 7,50 4,00 2,00 Tape VPE / packaging unit Polystyrene 1500 START Feeding direction Cover tape B B tolerance A ± 2,0 Tape width 16 mm 330,00 W2 B min. C ± 0,8 D min. N min. W1 +2 W2 max. W3 min. W3 max. 1,50 13,00 20,20 100,00 16,40 22,40 15,90 19,40 Top Tape C detail C Chip Cavity Sprocket Hole NO COMPONENT min 160mm COMPONENTS NO COMPONENT min. 100mm Embossment COVER TAPE min. 400mm Packaging is referred to the international standard IEC 60286 -3:2007 Drawn 165° -18 0v Checked Date 13-07-01 Name Fandrey 13-xx-xx xxxxxxxxx DESCRIPTION Packaging WS-DESV Description Drawing.- No. 461011220101 A4 Pull-of force Tape width 16 mm 0,1 N - 1,3 N SIZE REV FILE DATE BY System: Solid Edge ST4