Explaining SAR ADC Power Specifications

TECHNICAL ARTICLE
|
|
Join Tweet Connect
Explaining SAR ADC Power Specifications
by Alan Walsh, applications engineer, Analog Devices, Inc.
One of the mysteries—or at least the cause of considerable confusion—
of successive approximation register (SAR) ADCs is calculating their exact
power requirements at the system level. Data sheets can be confusing on
this specification.
Table 1. Example Power Dissipation from ADI’s AD7980 Data Sheet
SAR ADCs provide a low power means to measure input signals. Very often,
the power consumption scales with the sample rate, making for a very
efficient measurement system. This means that in order to calculate the
total power consumption of the ADC, all supply pins need to be taken into
account.
Conditions
Power
Dissipation
VDD ∙ 2.625 V,
VREF ∙ 5 V,
VIO ∙ 3 V
Min
10 kSPS throughput
Total
Typically, on SAR converters, there are three potential power consuming
rails: the VDD supply, the reference input, and the digital interface I/O supply.
The VDD supply provides power to the analog circuitry and ADC core.
On SARs that require an external reference, the reference input is a switched
capacitor that consumes charge current during the SAR conversion bit trials.
This can be a significant source of power consumption, depending on the
ADC throughput rate and size of the internal capacitor DAC. The higher
the ADC throughput, the more conversion bit trials (charging of caps), and
therefore, more current is consumed in the capacitive DAC array.
Parameter
1 MSPS throughput,
B Grade
1 MSPS throughput,
A Grade
Typ
Max
70
Unit
µW
7.0
9.0
mW
7.0
10
mW
VDD Only
4
mW
REF Only
1.7
mW
VIO Only
1.3
mW
When it comes to data sheets, especially with something as important as
power consumption, all specifications need to be taken into account and
stated separately like the AD7980 16-bit, 1 MSPS PulSAR® ADC shown above.
For more information on any of the above mentioned products visit
www.analog.com.
Similarly, a larger capacitor DAC means more capacitance to charge, which
results in a higher current draw. If the cap DAC is large, it may pose a problem to the reference drive circuit, and a higher power reference circuit may
be required. The same is true for the analog input, in which a more powerful
driving amplifier may be required to drive the higher capacitive DAC load during acquisition. Sometimes additional circuitry related to the analog input can
be powered from the reference, which can further add to power consumption.
Some ADCs have an internal reference buffer that gives the reference input
high impedance. In this scenario, the buffer supplies the necessary reference
current through another supply pin.
The digital I/O supply consumes power depending on the throughput/output
data rate, as well as load conditions on the data output lines. Again, higher
ADC throughput means more power consumed by the digital I/O, due to the
higher clock rates required to transfer the converted data. Any capacitive
loading on the data output lines will increase the digital I/O current because
of charging and discharging. Digital I/O current will also be output code
dependent; the worst case in which alternate ones and zeros are the output.
Typically, the digital I/O current should be measured with a signal present that
exercises most of the ADC output codes, such as a sinusoidal input. In high
throughput ADCs with high clock rates, the power consumed by the digital
interface can become quite significant.
Many data sheets will quote power for the VDD supply only. You have to dig
into the specification table to determine the reference and digital supply
power requirements. To get an accurate measure of the power consumption
from a system-level perspective, all three inputs need to be considered.
analog.com
Online Support Community
Engage with the Analog Devices
technology experts in our online
support community. Ask your
tough design questions, browse
FAQs, or join a conversation.
ez.analog.com.
Analog Devices, Inc.
Worldwide Headquarters
Analog Devices, Inc.
One Technology Way
P.O. Box 9106
Norwood, MA 02062-9106
U.S.A.
Tel: 781.329.4700
(800.262.5643,
U.S.A. only)
Fax: 781.461.3113
Analog Devices, Inc.
Europe Headquarters
Analog Devices, Inc.
Wilhelm-Wagenfeld-Str. 6
80807 Munich
Germany
Tel: 49.89.76903.0
Fax: 49.89.76903.157
Analog Devices, Inc.
Japan Headquarters
Analog Devices, KK
New Pier Takeshiba
South Tower Building
1-16-1 Kaigan, Minato-ku,
Tokyo, 105-6891
Japan
Tel: 813.5402.8200
Fax: 813.5402.1064
Analog Devices, Inc.
Asia Pacific Headquarters
Analog Devices
5F, Sandhill Plaza
2290 Zuchongzhi Road
Zhangjiang Hi-Tech Park
Pudong New District
Shanghai, China 201203
Tel: 86.21.2320.8000
Fax: 86.21.2320.8222
©2015 Analog Devices, Inc. All rights reserved.
Trademarks and registered trademarks are the
property of their respective owners.
TA12918-0-4/15
analog.com