Single Chip Realizes Direct-Conversion Rx

MWoct55
10/9/02
3:48 PM
Page 55
DESIGN
DIRECT-CONVERSION IC
Single Chip Realizes
Direct-Conversion Rx
d
Direct-conversion Rxs offer advantages
in simplicity compared to conventional
superheterodyne approaches, although
attention must be paid to some of the
trade-offs.
irect conversion of RF signals to baseband has long been a
goal of communications systems designers. The approach
can eliminate expensive and bulky hardware, but at the
cost of some trade-offs in performance. What follows is an
nent count, along with the
direct-conversion receiver (Rx) compared to a traditional elimination of expensive filtering has made direct consuperheterodyne architecture, as well as details on a new
version very appealing as an
direct-conversion Rx integrated-circuit
architecture for transmit and receive
(IC) subsystem.
functions. However, it is only recently
The function of a conventional
that components which facilitate its
superheterodyne Rx (Fig. 1, left) and
practical implementation have become
a direct-conversion Rx (Fig. 1, right)
available.
is the same: translating and condiAlthough the direct-conversion
EAMON NASH
tioning
signals
downward
in
frequenapproach
reduces the component count,
Applications Engineer
cy
so
that
they
can
be
sampled
by
lowit
also
adds
design challenges. In the superAnalog Devices, 804 Woburn St.,
frequency (baseband) analog-to-digital
heterodyne approach (Fig. 1, left), by
Wilmington, MA 01887; (781) 937-1239,
e-mail: eamon.nash@ analog.com.
converters (ADCs). As is apparent
driving the mixer with a frequencyfrom
a
comparison
of
the
two
block
agile LO, the frequency of the desired
YUPING TOH
diagrams,
the
direct-conversion
syssignal or channel (which is generally
Applications Engineer
tem
achieves
this
function
with
convaries in a multi-user system) is converted
Analog Devices, 804 Woburn St.,
siderably fewer components.
to a fixed frequency. Once the desired
Wilmington, MA 01887; (781) 937-2418,
e-mail: [email protected].
In a conventional single- or doublesignal has been converted to a fixed IF,
conversion
superheterodyne
Rx,
the
it can be processed by highly selective
GARY HENDRICKSON
modulated RF signal is translated in
narrowband filtering using a surfaceStaff Applications Engineer
frequency through one or more interacoustic-wave (SAW) filter. In addiAnalog Devices, 7910 Triad Center Dr.,
Greensboro, NC 27409; (336) 605-4344,
mediate frequencies (IFs) before being
tion, all subsequent frequency translae-mail: [email protected].
converted back to its desired baseband
tions can be effected using fixed-frequency
format. At IF, the signal is filtered and
LOs.
amplified before being mixed to a lower
The other important function perfrequency. In a direct-conversion Rx,
formed at IF in a superheterodyne systhe modulated RF signal is mixed with
tem is signal amplification. Fixed-gain
a local oscillator (LO) at exactly the
amplification, in the form of low-noise
same frequency.
amplifiers (LNAs), is generally applied
The obvious reduction of compoat RF, while signal leveling is generalexamination of the trade-offs associated with designing a
MICROWAVES & RF
55
OCTOBER 2002
visit PlanetEE.com
MWoct56
10/9/02
3:48 PM
Page 56
DESIGN
IQ
demod
Splitter/
Combiner
High-power
amplifier
AMP
0
90
VGA
LNA
ADC
RSSI/
AGC
Duplexer/
Switch
VCO/Synth
RF VGA
DAC
VGA
Mixer
RF power
detection
and control
ADC
ADC
Mixer
LNA
IQ
demod
High-power
amplifier
0
90
0
90
VGA
ADC
RSSI/
AGC
VCO/Synth
RF VGA
DAC
DAC
IQ mod
RF power
detection
and control
0
90
DAC
IQ mod
1. A conventional single-conversion superheterodyne Rx translates the frequency of desired signals through one or more IFs
before converting it to baseband. A direct-conversion Rx makes the transition directly from RF to baseband.
ly accomplished through the use of variDevices (Norwood, MA). This Rx IC can
imately 3 GHz), but they are generalable-gain amplifiers (VGAs). Since it
demodulate signals from 0.8 to 2.7
ly more expensive than lower-frequency
is easier to design a high-gain-range
GHz. The device consists of a number
IF filters due to the higher quality-facVGA at lower frequencies, and because
of subcircuits that can be configured
tor (Q) requirements.
many unwanted signal components
separately. The IC includes all of the
A cost-effective means of realizing a
have already been removed from the carcomponents required for amplification,
direct-conversion Rx is through monorier by the time it is translated to IF, varidownconversion, and filtering in a directlithic fabrication, by including as many
able-gain amplification is generally perconversion demodulation circuit.
of the required components on a single
formed at IF or baseband frequencies.
Since gain control in a direct-conchip, such as the AD8347 direct-conThis “distribution” of gain avoids a
version design must be implemented at
version Rx IC (Fig. 2) from Analog
concentration of high gain at
the Rx’s front-end portion,
VPS1
VPS2 VPS3 VREF
IMXO IOFS
IAIN
IOPP IOPN
which can cause saturation of
2
8
6
4
3
21
12
14
13
subsequent stages, especially
VREF
+
if large in-band or out-of-band
AD8347
signal blockers are present.
–
Bias
ENBL 15
While the appeal of a direct5 VCMC
cell
VREF
VCMO
conversion Rx lies in its elimination of IF stages, therein
Phase
Phase 1 LOIN
RFIN 10
splitter
splitter
lies its weakness. Because there
2
1
RFIP 11
28 LOIP
is no longer an IF stage at
which signal leveling and filVCMO
7 COM3
tering can be conveniently per2 pF
+
9 COM2
formed, all signal conditionGainDET2
DET1
23 COM3
VREF
ing must be performed either
VGIN 17 control
–
interface
27 COM1
at RF or baseband. In a mul20
19
18
22
16
24
25 26
tichannel system, the capaQOPP QOPN
VDT1 VAGC VDT2 QMXO QOFS
QAIN
bilities of RF filters are limited (they cannot be
2. The AD8347 is comprised of a 70-dB VGA with AGC mode, an I/Q demodulator and
narrowband), at best screening out-oftwo 30-dB-gain baseband amplifiers. An internal +1-VDC voltage reference provides
band interferers. SAW filters are availbiasing.
able for some RF uses (through approxMICROWAVES & RF
56
OCTOBER 2002
p55,56,58,60,61,62,65,67 10/9/02
10/9/02 3:02
3:02PM
PM Page
Page
Page58
58
58 (Black
(Yellow
(Cyan
(Magenta
plate)
plate)
plate)
45
40
35
30
25
20
15
10
5
0
–5
–10
–15
–20
–25
–30
–35
14
12
–40°C
10
+25°C
8
6
+85°C
4
+25°C
2
0
–2
+25°C
–4
–40°C
Linearity error—dB
RF and/or at baseband, the AD8347
employs three stages of VGA. Two
stages are employed at RF and one at
baseband, following the I/Q demodulator.
The three VGA stages, which have a
convenient linear-in-dB gain-control
relationship, are controlled in parallel.
Each of the two RF VGAs has a gain range
from –10 to +13 dB. The combined
gain range of the mixer and the baseband
VGA is –10 to +14 dBm. The overall gain
range from the RF input to the mixer output is therefore –30 to +40 dB.
The gain of the VGA is set by the voltage on the AD8347’s VGIN pin, which
is a high-impedance input port. Figure
3 shows a plot of the gain versus gaincontrol voltage, along with the linearity of the gain-control function. Note that
the sense of the gain-control voltage is
negative. As the gain-control voltage
increases from +0.2 to +1.2 VDC, the
gain decreases from +40 to –30 dB.
The VGA can be driven by an exter-
Mixer gain—dB
| DIRECT-CONVERSION IC |
DESIGN
–6
–8
–10
–12
0.2
0.3
0.4
0.5
0.6
0.7
0.8
Vgin—V
0.9
1.0
1.1
1.2
3. The three-stage VGA (two stages at RF, one stage at baseband) varies gain from
–30 to +40 dB. The gain-control function is linear-in-dB over its range.
nal voltage source [generally a digitalto-analog converter (DAC)] or by an automatic-gain-control (AGC) circuit built
into the device. The AGC circuit con-
sists of two root-mean-square (RMS)
detectors and an error amplifier. When
the AGC circuit is being used, the two
mixer outputs are connected to the
MWoct60
10/9/02
3:49 PM
Page 60
DESIGN
C1
4.7 pF
RS
91 C3
8.2 pF
L1
L3
0.68 H
1.2 H
C2
150 pF
C4
82 pF
IMXO
SYNTHESIZERS •
VREF
RL
100 IAIN VDT1
AD8347
4. The demodulated output (baseband-mixer output) can be
filtered off-chip before being applied to the final baseband
amplifiers. The on-chip reference voltage signal (VREF) provides biasing for the filter circuit.
inputs of the two detectors. The signals (currents) from the
detectors are compared with a set-point signal and an error
signal is generated. The AGC circuit is completed by connecting the error signal to the Rx’s VGIN gain-control input
pin. With the AGC circuit activated, the mixer’s output will
remain constant for input levels from –55 to + 5 dBm.
Because this output has a 90-MHz bandwidth, downconversion
to a low IF is also possible.
The mixer is a quadrature demodulator between the RF
and baseband VGAs. It produces in-phase (I) and quadrature
(Q) baseband outputs. To achieve low error-vector magnitude (EVM) in (direct-conversion) digital demodulation, precise quadrature splitting and amplitude balance of the LO signal is required. The AD8347 achieves typical phase and
amplitude balances of 3 deg. and 0.3 dB, respectively, from
0.8 to 2.7 GHz.
LO leakage within a direct-conversion system is one of the
key challenges to implementing a high-sensitivity direct-conversion Rx. In direct-conversion and superheterodyne Rxs,
some of the LO signal will leak through to the RF input. LO
leakage to the RF input will cause self-mixing, which will produce a troublesome DC component at the mixer output. This
DC component, if large enough, can lead to saturation of the
baseband output signal (to either rail). In addition, because
LO leakage is typically frequency dependent, the extent of
the DC offset will also vary with frequency, making simple
offset compensation difficult.
In a conventional Rx, even if the first downconversion produces a DC component, this component will be harmless as
it will be removed by IF filtering. This is an argument for using
a direct-conversion Rx to mix the signal down to a low IF
(instead of all the way to baseband) and digitizing those signals using IF sampling. The 90-MHz bandwidth of the
AD8347’s mixer output easily facilitates this.
The AD8347 uses two techniques to minimize the effects
of LO leakage. First, the use of an active mixer means that
the LO level can be set quite low. In the case of the AD8347,
MICROWAVES & RF
60
OCTOBER 2002
MWoct61
10/9/02
3:49 PM
Page 61
DESIGN
the recommended level is –8 dBm.
The device also contains a circuit
that actively reduces DC offsets that
appear at the output of the baseband
VGA. Internally, the average level on
the baseband outputs is compared to their
nominal bias levels of +1 VDC. If there
is any discrepancy between these two
voltages, the average level at the mixer
output is slowly servo-controlled back
to +1 VDC. The settling time to this levelcorrecting circuit can be controlled
through external capacitors.
Because the output of the mixer/VGA
circuit and the input to the final baseband amplifiers are separately pinned
out, baseband lowpass or bandpass filtering can be conveniently performed
before the signal faces its final amplification stage. The mixer/VGA output
and the baseband amplifier inputs are
biased to the same reference voltage
level (of +1 VDC at VREF), making a
DC-coupled connection permissible.
Figure 4 shows a schematic diagram
for a 100-Ω, fourth-order elliptic lowpass filter with a 3-dB cutoff of 20 MHz.
Source and load impedances of approximately 100 Ω ensure that the filter
experiences a matched source and load.
This also ensures that the mixer output is driving an overall load of 200 Ω.
Note that the shunt-termination resistor is tied to the reference voltage VREF
and not to ground.
The AD8347’s baseband amplifiers
take single-ended input signals and boost
them by 30 dB to produce a differential
output which can be independently
biased. The VOCM input pin, which sets
the output common-mode level, can be
driven by the AD8347’s internal +1VDC reference. Alternatively, the VOCM
pin can be driven by an external reference voltage. In general, when the VOCM
pin is driven externally, the drive voltage should come from the ADC that
the AD8347 is driving. The differential
outputs are capable of swinging from +0.4
VDC above ground to within +1.3 VDC
of the supply voltage and have a 3-dB
bandwidth of 65 MHz.
Figure 5 shows a block diagram of
a complete Rx signal chain that can be
used to demodulate various signal types,
61
MWoct62
10/9/02
3:49 PM
Page 62
| DIRECT-CONVERSION IC |
DESIGN
5. A complete direct-conversion Rx can be assembled using the ADF4112, AD8347, and AD9218 ICs.
including higher-order quadrature30-MHz frequency offset results. This
able for rates of 40, 60, 80, and 100
amplitude-modulation (QAM) signals.
30-MHz offset (and including the freMSamples/s.
The evaluation system includes the
quency deviations of the modulation)
The high-encode-rate capability and
ADF4112 phase-locked loop (PLL),
is well-within the 65-MHz bandwidth
high analog bandwidth of the AD8347
with a range of 0.2 to 3 GHz, which easof the AD8347’s output amplifiers, as
also make possible IF sampling appliily covers the 0.8-to-2.7-GHz LO range
well as the analog bandwidth of the
cations. By running a 1.9-GHz LO with
of the AD8347. In this evaluation sysAD9218 ADC. The AD9218 successRF signals at 1.93 GHz, a (modulated)
tem, a 1.9-GHz voltagefully mixed down these 30controlled oscillator (VCO)
MHz offset signals to basewas used with the PLL, and
band frequencies, showing
a 1:1 balun was inserted
the AD8347/AD9218 combetween the PLL and the
bination to be suitable for
AD8347’s LO input to prosome IF sampling applicavide a differential drive.
tions. To evaluate the
The I/Q outputs of the
AD8347 as a direct-conAD8347, biased to the
version Rx operating with
AD8347’s internal refercomplex modulation, RF
ence voltage, connect directinput signals to the AD8347
ly to the differential inputs
were supplied from an
of the AD9218 dual ADC.
SMIQ-series vector-signal
The AD9218 is a dual 10generator from Rohde &
b device available for samSchwarz (Munich, Gerpling rates of 40, 65, 80,
many). The instrument is
and 105 MSamples/s (the
capable of providing clean
105-MSamples/s version
1.9-GHz RF signals with a
was used in this measurement
variety of modulation forsetup). For lower-order modmats, including 16QAM
ulation schemes, it is possible 6. Using a reconstruction DAC, the (digitized) demodulated constel- and 64QAM.
to use the AD9288, a dual lation for a 2-MSymbol/s, 16-QAM signal can be displayed on a stanThe AD8347 and
8-b ADC with versions avail- dard oscilloscope screen.
ADF4112 can operate at
MICROWAVES & RF
62
OCTOBER 2002
MWoct65
10/9/02
3:50 PM
Page 65
DESIGN
supply voltages from +3 to +5 VDC. For
the evaluation setup, a +3-VDC supply
was used, matching the power-supply
level of the AD9218. Baseband filtering prior to final output amplification
(to improve performance through the
elimination of out-of-band noise) is
possible on the AD8347 evaluation
board, but was not done during this
evaluation. The AD8347’s VGA was set
to run in AGC mode. In this mode, the
mixer output settles to a level of approximately 24 mV peak to peak, resulting
in a 760-mV peak-to-peak differential
voltage at the baseband amplifier outputs. In addition to baseband lowpass
filtering, the signal-to-noise ratio (SNR)
of the demodulated signal can be
With an input range from
0.8 to 2.7 GHz, the AD8347
is suitable for a broad range
of markets. For systems
operating beyond 2.7 GHz, it
can also be used as an IF-tobaseband converter.
improved by increasing the mixer output levels beyond this nominal 24-mV
peak-to-peak level.1
The standard ADF4112 PLL printed-circuit board (PCB) is shipped with
an 800-MHz external VCO. For this
evaluation of the AD8347, the PLL
module’s 800-MHz VCO was replaced
with a 1.9-GHz VCO. Tuning of the
AD4112’s output frequency was easily accomplished through the parallel
port using a software package supplied
with the PLL by Analog Devices. The
PLL module’s PCB also features an onboard 10-MHz crystal-oscillator reference source, which was bypassed to
allow for synchronization with external RF source (the SMIQ-series vector-signal generator).
Before measurements could be made,
the evaluation board for the AD9218
ADC required some modifications to
enable common clocking and to meet
65
MWoct67
10/9/02
3:53 PM
Page 67
DESIGN
the limited drive capability of the clock
source. The bit clock from the SMIQseries vector-signal generator supplied
the required encode clock for the
AD9218. For a 2-Msymbol/s data rate,
this corresponded to an 8-MHz clock
rate for 16QAM. The analog input 50Ω termination resistors on the PCB
were switched to 1-kΩ terminations to
accommodate the limited drive capability
of the AD8347’s baseband output amplifiers. This resulted in approximately
400-mV signal swings to the ADC
(which has a full-scale input range of
500 mV). To minimize transmission-line
effects, this meant keeping cabling
between boards as short as possible.
The evaluation setup supported the display of 16QAM and 64QAM constellations by reconstructing the ADC outputs using an AD9763 DAC and
displaying the I and Q outputs on an oscilloscope in X-Y mode (Fig. 6).
With an input range from 0.8 to 2.7
GHz, the AD8347 is suitable for a
broad range of markets. Applications
include point-to-point and point-tomultipoint radios, built-in-test-equipment (BITE) systems in cellular base
stations, and auxiliary Rx systems in linear high-power amplifiers (HPAs). For
systems operating beyond 2.7 GHz, it
can also be used as an IF-to-baseband
converter. MRF
REFERENCES
1. AD8347 0.8-2.7 GHz Direct Conversion Modulator, Analog
Devices, Norwood, MA, 2001, pp 15-16.
Your
Online
Resource
For RF and Microwave
Products and Manufacturers
If you need a part, you’ll find it at:
www.m-rf.com
67