14-Bit, 150 MSPS, 1.8 V Analog-to-Digital Converter AD9254 FEATURES FUNCTIONAL BLOCK DIAGRAM AVDD AD9254 VIN+ VIN– Macro, micro, and pico cell infrastructure GENERAL DESCRIPTION The AD9254 is a monolithic, single 1.8 V supply, 14-bit, 150 MSPS analog-to-digital converter (ADC), featuring a high performance sample-and-hold amplifier (SHA) and on-chip voltage reference. The product uses a multistage differential pipeline architecture with output error correction logic to provide 14-bit accuracy at 150 MSPS data rates and guarantees no missing codes over the full operating temperature range. The wide bandwidth, truly differential SHA allows a variety of user-selectable input ranges and offsets, including single-ended applications. It is suitable for multiplexed systems that switch full-scale voltage levels in successive channels and for sampling single-channel inputs at frequencies well beyond the Nyquist rate. Combined with power and cost savings over previously available ADCs, the AD9254 is suitable for applications in communications, imaging, and medical ultrasound. A differential clock input controls all internal conversion cycles. A duty cycle stabilizer (DCS) compensates for wide variations in the clock duty cycle while maintaining excellent overall ADC performance. 8-STAGE 1 1/2-BIT PIPELINE MDAC1 SHA 4 8 A/D 3 A/D REFT REFB CORRECTION LOGIC OR 15 OUTPUT BUFFERS DCO D13 (MSB) VREF D0 (LSB) SENSE 0.5V REF SELECT AGND APPLICATIONS Ultrasound equipment IF sampling in communications receivers CDMA2000, WCDMA, TD-SCDMA, and WiMax Battery-powered instruments Hand-held scopemeters Low cost digital oscilloscopes DRVDD CLOCK DUTY CYCLE STABILIZER CLK+ CLK– SCLK/DFS MODE SELECT PDWN SDIO/DCS CSB DRGND 06216-001 1.8 V analog supply operation 1.8 V to 3.3 V output supply SNR = 71.8 dBc (72.8 dBFS) to 70 MHz input SFDR = 84 dBc to 70 MHz input Low power: 430 mW @ 150 MSPS Differential input with 650 MHz bandwidth On-chip voltage reference and sample-and-hold amplifier DNL = ±0.4 LSB Flexible analog input: 1 V p-p to 2 V p-p range Offset binary, Gray code, or twos complement data format Clock duty cycle stabilizer Data output clock Serial port control Built-in selectable digital test pattern generation Programmable clock and data alignment Figure 1. The digital output data is presented in offset binary, Gray code, or twos complement formats. A data output clock (DCO) is provided to ensure proper latch timing with receiving logic. The AD9254 is available in a 48-lead LFCSP_VQ and is specified over the industrial temperature range (−40°C to +85°C). PRODUCT HIGHLIGHTS 1. The AD9254 operates from a single 1.8 V power supply and features a separate digital output driver supply to accommodate 1.8 V to 3.3 V logic families. 2. The patented SHA input maintains excellent performance for input frequencies up to 225 MHz. 3. The clock DCS maintains overall ADC performance over a wide range of clock pulse widths. 4. A standard serial port interface supports various product features and functions, such as data formatting (offset binary, twos complement, or Gray coding), enabling the clock DCS, power-down, and voltage reference mode. 5. The AD9254 is pin-compatible with the AD9233, allowing a simple migration from 12 bits to 14 bits. Rev. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2006 Analog Devices, Inc. All rights reserved. AD9254 TABLE OF CONTENTS Features .............................................................................................. 1 Timing ......................................................................................... 20 Applications....................................................................................... 1 Serial Port Interface (SPI).............................................................. 21 General Description ......................................................................... 1 Configuration Using the SPI..................................................... 21 Functional Block Diagram .............................................................. 1 Hardware Interface..................................................................... 21 Product Highlights ........................................................................... 1 Configuration Without the SPI ................................................ 21 Revision History ............................................................................... 2 Memory Map .................................................................................. 22 Specifications..................................................................................... 3 Reading the Memory Map Register Table............................... 22 DC Specifications ......................................................................... 3 Memory Map Register Table..................................................... 23 AC Specifications.......................................................................... 4 Layout Considerations................................................................... 25 Digital Specifications ................................................................... 5 Power and Ground Recommendations ................................... 25 Switching Specifications .............................................................. 6 CML ............................................................................................. 25 Timing Diagram ........................................................................... 6 RBIAS........................................................................................... 25 Absolute Maximum Ratings............................................................ 7 Reference Decoupling................................................................ 25 Thermal Resistance ...................................................................... 7 Evaluation Board ............................................................................ 26 ESD Caution.................................................................................. 7 Power Supplies ............................................................................ 26 Pin Configuration and Function Descriptions............................. 8 Input Signals................................................................................ 26 Equivalent Circuits ........................................................................... 9 Output Signals ............................................................................ 26 Typical Performance Characteristics ........................................... 10 Default Operation and Jumper Selection Settings................. 27 Theory of Operation ...................................................................... 14 Alternative Clock Configurations............................................ 27 Analog Input Considerations.................................................... 14 Alternative Analog Input Drive Configuration...................... 27 Differential Input Configurations ............................................ 15 Schematics................................................................................... 29 Voltage Reference ....................................................................... 16 Evaluation Board Layout........................................................... 34 Clock Input Considerations ...................................................... 17 Bill of Materials........................................................................... 37 Jitter Considerations .................................................................. 19 Outline Dimensions ....................................................................... 40 Power Dissipation and Standby Mode..................................... 19 Ordering Guide .......................................................................... 40 Digital Outputs ........................................................................... 20 REVISION HISTORY 10/06—Revision 0: Initial Version Rev. 0 | Page 2 of 40 AD9254 SPECIFICATIONS DC SPECIFICATIONS AVDD = 1.8 V; DRVDD = 2.5 V, maximum sample rate, 2 V p-p differential input, 1.0 V internal reference; AIN = −1.0 dBFS, DCS enabled, unless otherwise noted. Table 1. Parameter RESOLUTION ACCURACY No Missing Codes Offset Error Gain Error Differential Nonlinearity (DNL) 1 Integral Nonlinearity (INL)1 TEMPERATURE DRIFT Offset Error Gain Error INTERNAL VOLTAGE REFERENCE Output Voltage Error (1 V Mode) Load Regulation @ 1.0 mA INPUT REFERRED NOISE VREF = 1.0 V ANALOG INPUT Input Span, VREF = 1.0 V Input Capacitance 2 REFERENCE INPUT RESISTANCE POWER SUPPLIES Supply Voltage AVDD DRVDD Supply Current IAVDD1 IDRVDD1(DRVDD = 1.8 V) IDRVDD1 (DRVDD = 3.3 V) POWER CONSUMPTION DC Input Sine Wave Input1 (DRVDD = 1.8 V) Sine Wave Input1 (DRVDD = 3.3 V) Standby Power 3 Power-Down Power Temperature Full Min 14 AD9254BCPZ-150 Typ Max Unit Bits Full Full Full 25°C Full 25°C Full Guaranteed ±0.3 ±0.8 ±0.6 ±4.5 ±0.4 ±1.0 ±1.5 ±5.0 % FSR % FSR LSB LSB LSB LSB Full Full ±15 ±95 ppm/°C ppm/°C Full Full ±5 7 25°C 1.3 LSB rms Full Full Full 2 8 6 V p-p pF kΩ Full Full mV mV 1.8 2.5 1.9 3.6 V V Full Full Full 240 11 23 260 mA mA mA Full Full Full Full Full 430 450 506 40 1.8 470 mW mW mW mW mW 1 1.7 1.7 ±35 Measured with a low input frequency, full-scale sine wave, with approximately 5 pF loading on each output bit. Input capacitance refers to the effective capacitance between one differential input pin and AGND. Refer to Figure 4 for the equivalent analog input structure. 3 Standby power is measured with a dc input, the CLK pin inactive (set to AVDD or AGND). 2 Rev. 0 | Page 3 of 40 AD9254 AC SPECIFICATIONS AVDD = 1.8 V; DRVDD = 2.5 V, maximum sample rate, 2 V p-p differential input, 1.0 V internal reference; AIN = −1.0 dBFS, DCS enabled, unless otherwise noted. Table 2. Parameter 1 SIGNAL-TO-NOISE-RATIO (SNR) fIN = 2.4 MHz fIN = 70 MHz fIN = 100 MHz fIN = 170 MHz SIGNAL-TO-NOISE AND DISTORTION (SINAD) fIN = 2.4 MHz fIN = 70 MHz fIN = 100 MHz fIN = 170 MHz EFFECTIVE NUMBER OF BITS (ENOB) fIN = 2.4 MHz fIN = 70 MHz fIN = 100 MHz fIN = 170 MHz WORST SECOND OR THIRD HARMONIC fIN = 2.4 MHz fIN = 70 MHz fIN = 100 MHz fIN = 170 MHz SPURIOUS-FREE DYNAMIC RANGE (SFDR) fIN = 2.4 MHz fIN = 70 MHz fIN = 100 MHz fIN = 170 MHz WORST OTHER (HARMONIC OR SPUR) fIN = 2.4 MHz fIN = 70 MHz fIN = 100 MHz fIN = 170 MHz TWO-TONE SFDR fIN = 29 MHz (−7 dBFS ), 32 MHz (−7 dBFS ) fIN = 169 MHz (−7 dBFS ), 172 MHz (−7 dBFS ) ANALOG INPUT BANDWIDTH 1 Temperature 25°C 25°C Full 25°C 25°C 25°C 25°C Full 25°C 25°C Min AD9254BCPZ-150 Typ Max 72.0 71.8 Unit dBc dBc dBc dBc dBc 70.0 71.6 70.8 71.7 71.0 70.6 69.8 dBc dBc dBc dBc dBc 25°C 25°C 25°C 25°C 11.7 11.7 11.6 11.5 Bits Bits Bits Bits 25°C 25°C Full 25°C 25°C −90 −84 dBc dBc dBc dBc dBc 25°C 25°C Full 25°C 25°C 90 84 69.0 −74 −83 −80 dBc dBc dBc dBc dBc 74 83 80 25°C 25°C Full 25°C 25°C −93 −93 −90 −90 dBc dBc dBc dBc dBc 25°C 25°C 25°C 90 90 650 dBFS dBFS MHz See Application Note AN-835, Understanding High Speed ADC Testing and Evaluation, for a complete set of definitions. Rev. 0 | Page 4 of 40 −85 AD9254 DIGITAL SPECIFICATIONS AVDD = 1.8 V; DRVDD = 2.5 V, maximum sample rate, 2 V p-p differential input, 1.0 V internal reference; AIN = −1.0 dBFS, DCS enabled, unless otherwise noted. Table 3. Parameter DIFFERENTIAL CLOCK INPUTS (CLK+, CLK−) Logic Compliance Internal Common-Mode Bias Differential Input Voltage Input Voltage Range Input Common-Mode Range High Level Input Voltage (VIH) Low Level Input Voltage (VIL) High Level Input Current (IIH) Low Level Input Current (IIL) Input Resistance Input Capacitance LOGIC INPUTS (SCLK/DFS, OEB, PWDN) High Level Input Voltage (VIH) Low Level Input Voltage (VIL) High Level Input Current (IIH) Low Level Input Current (IIL) Input Resistance Input Capacitance LOGIC INPUTS (CSB) High Level Input Voltage (VIH) Low Level Input Voltage (VIL) High Level Input Current (IIH) Low Level Input Current (IIL) Input Resistance Input Capacitance LOGIC INPUTS (SDIO/DCS) High Level Input Voltage (VIH) Low Level Input Voltage (VIL) High Level Input Current (IIH) Low Level Input Current (IIL) Input Resistance Input Capacitance DIGITAL OUTPUTS DRVDD = 3.3 V High Level Output Voltage (VOH, IOH = 50 μA) High Level Output Voltage (VOH, IOH = 0.5 mA) Low Level Output Voltage (VOL, IOL = 1.6 mA) Low Level Output Voltage (VOL, IOL = 50 μA) DRVDD = 1.8 V High Level Output Voltage (VOH, IOH = 50 μA) High Level Output Voltage (VOH, IOH = 0.5 mA) Low Level Output Voltage (VOL, IOL = 1.6 mA) Low Level Output Voltage (VOL, IOL = 50 μA) Temperature Full Full Full Full Full Full Full Full Full Full Min AD9254BCPZ-150 Typ Max Unit 6 AVDD + 1.6 AVDD 3.6 0.8 +10 +10 12 V V p-p V V V V μA μA kΩ pF CMOS/LVDS/LVPECL 1.2 0.2 AVDD − 0.3 1.1 1.2 0 −10 −10 8 Full Full Full Full Full Full 1.2 0 −50 −10 Full Full Full Full Full Full 1.2 0 −10 +40 Full Full Full Full Full Full 1.2 0 −10 +40 Full Full Full Full 3.29 3.25 Full Full Full Full 1.79 1.75 10 4 3.6 0.8 −75 +10 V V μA μA kΩ pF 3.6 0.8 +10 +135 V V μA μA kΩ pF DRVDD + 0.3 0.8 +10 +130 V V μA μA kΩ pF 30 2 26 2 26 5 Rev. 0 | Page 5 of 40 0.2 0.05 V V V V 0.2 0.05 V V V V AD9254 SWITCHING SPECIFICATIONS AVDD = 1.8 V, DRVDD = 2.5 V, unless otherwise noted. Table 4. Parameter 1 CLOCK INPUT PARAMETERS Conversion Rate, DCS Enabled Conversion Rate, DCS Disabled CLK Period CLK Pulse Width High, DCS Enabled CLK Pulse Width High, DCS Disabled DATA OUTPUT PARAMETERS Data Propagation Delay (tPD) 2 DCO Propagation Delay (tDCO) Setup Time (tS) Hold Time (tH) Pipeline Delay (Latency) Aperture Delay (tA) Aperture Uncertainty (Jitter, tJ) Wake-Up Time 3 OUT-OF-RANGE RECOVERY TIME SERIAL PORT INTERFACE 4 SCLK Period (tCLK) SCLK Pulse Width High Time (tHI) SCLK Pulse Width Low Time (tLO) SDIO to SCLK Setup Time (tDS) SDIO to SCLK Hold Time (tDH) CSB to SCLK Setup Time (tS) CSB to SCLK Hold Time (tH) Temperature Min Full Full Full Full Full 20 10 6.7 2.0 3.0 Full Full Full Full Full Full Full Full Full 3.1 AD9254BCPZ-150 Typ Max 150 150 1.9 3.0 Full Full Full Full Full Full Full 3.3 3.3 4.7 3.7 3.9 4.4 2.9 3.8 12 0.8 0.1 350 3 4.8 40 16 16 5 2 5 2 See Application Note AN-835, Understanding High Speed ADC Testing and Evaluation, for a complete set of definitions. Output propagation delay is measured from CLK 50% transition to DATA 50% transition, with 5 pF load. Wake-up time is dependent on the value of the decoupling capacitors, values shown with 0.1 μF capacitor across REFT and REFB. 4 See Figure 50 and the Serial Port Interface (SPI) section. 2 3 TIMING DIAGRAM N+2 N+3 N N+4 tA N+8 N+5 N+6 N+7 N–7 N–6 tCLK CLK+ CLK– tPD N – 13 tS N – 12 N – 11 tH N – 10 N–9 N–8 tDCO DCO Figure 2. Timing Diagram Rev. 0 | Page 6 of 40 tCLK N–5 N–4 06216-002 DATA MSPS MSPS ns ns ns ns ns ns ns Cycles ns ps rms μs Cycles ns ns ns ns ns ns ns 1 N+1 Unit AD9254 ABSOLUTE MAXIMUM RATINGS Table 5. Parameter ELECTRICAL AVDD to AGND DRVDD to DGND AGND to DGND AVDD to DRVDD D0 through D13 to DGND DCO to DGND OR to DGND CLK+ to AGND CLK− to AGND VIN+ to AGND VIN− to AGND VREF to AGND SENSE to AGND REFT to AGND REFB to AGND SDIO/DCS to DGND PDWN to AGND CSB to AGND SCLK/DFS to AGND OEB to AGND ENVIRONMENTAL Storage Temperature Range Operating Temperature Range Lead Temperature (Soldering 10 Sec) Junction Temperature Rating −0.3 V to +2.0 V −0.3 V to +3.9 V −0.3 V to +0.3 V −3.9 V to +2.0 V −0.3 V to DRVDD + 0.3 V −0.3 V to DRVDD + 0.3 V −0.3 V to DRVDD + 0.3 V −0.3 V to +3.9 V −0.3 V to +3.9 V −0.3 V to AVDD + 0.2 V −0.3 V to AVDD + 0.2 V −0.3 V to AVDD + 0.2 V −0.3 V to AVDD + 0.2 V −0.3 V to AVDD + 0.2 V −0.3 V to AVDD + 0.2 V −0.3 V to DRVDD + 0.3 V −0.3 V to +3.9 V −0.3 V to +3.9 V −0.3 V to +3.9 V −0.3 V to +3.9 V –65°C to +125°C –40°C to +85°C 300°C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. THERMAL RESISTANCE The exposed paddle must be soldered to the ground plane for the LFCSP_VQ package. Soldering the exposed paddle to the customer board increases the reliability of the solder joints, maximizing the thermal capability of the package. Table 6. Thermal Resistance Package Type 48-lead LFCSP_VQ (CP-48-3) θJA 26.4 θJC 2.4 Unit °C/W Typical θJA and θJC are specified for a 4-layer board in still air. Airflow increases heat dissipation, effectively reducing θJA. In addition, metal in direct contact with the package leads from metal traces and through holes, ground, and power planes, reduces the θJA. ESD CAUTION 150°C Rev. 0 | Page 7 of 40 AD9254 48 47 46 45 44 43 42 41 40 39 38 37 DRVDD DRGND D1 D0 (LSB) DCO OEB AVDD AGND AVDD CLK– CLK+ AGND PIN CONFIGURATION AND FUNCTION DESCRIPTIONS D2 D3 1 2 PIN 1 INDICATOR D4 3 D5 4 D6 5 D7 6 DRGND 7 DRVDD 8 D8 9 D9 10 D10 11 D11 12 AD9254 PDWN RBIAS CML AVDD AGND VIN– VIN+ AGND REFT REFB VREF SENSE 06216-003 D12 D13 (MSB) OR DRGND DRVDD SDIO/DCS SCLK/DFS CSB AGND AVDD AGND AVDD 13 14 15 16 17 18 19 20 21 22 23 24 TOP VIEW (Not to Scale) 36 35 34 33 32 31 30 29 28 27 26 25 Figure 3. Pin Configuration Table 7. Pin Function Description Pin No. 0, 21, 23, 29, 32, 37, 41 45, 46, 1 to 6, 9 to 14 7, 16, 47 8, 17, 48 15 18 Mnemonic AGND Description Analog Ground. (Pin 0 is the exposed thermal pad on the bottom of the package.) D0 (LSB) to D13 (MSB) Data Output Bits. DRGND DRVDD OR SDIO/DCS Digital Output Ground. Digital Output Driver Supply (1.8 V to 3.3 V). Out-of-Range Indicator. Serial Port Interface (SPI) Data Input/Output (Serial Port Mode); Duty Cycle Stabilizer Select (External Pin Mode). See Table 10. Serial Port Interface Clock (Serial Port Mode); Data Format Select Pin (External Pin Mode). Serial Port Interface Chip Select (Active Low). See Table 10. Analog Power Supply. Reference Mode Selection. See Table 9. Voltage Reference Input/Output. Differential Reference (−). Differential Reference (+). Analog Input Pin (+). Analog Input Pin (−). Common-Mode Level Bias Output. External Bias Resistor Connection. A 10 kΩ resistor must be connected between this pin and analog ground (AGND). Power-Down Function Select. Clock Input (+). Clock Input (−). Output Enable (Active Low). Data Clock Output. 19 20 22, 24, 33, 40, 42 25 26 27 28 30 31 34 35 SCLK/DFS CSB AVDD SENSE VREF REFB REFT VIN+ VIN– CML RBIAS 36 38 39 43 44 PDWN CLK+ CLK– OEB DCO Rev. 0 | Page 8 of 40 AD9254 EQUIVALENT CIRCUITS 1kΩ SCLK/DFS OEB PDWN 30kΩ 06216-008 06216-004 VIN Figure 4. Equivalent Analog Input Circuit Figure 8. Equivalent SCLK/DFS, OEB, PDWN Input Circuit AVDD AVDD 26kΩ 1.2V 1kΩ CLK– 06216-005 CLK+ CSB 10kΩ 06216-009 10kΩ Figure 9. Equivalent CSB Input Circuit Figure 5. Equivalent Clock Input Circuit DRVDD SENSE 1kΩ 1kΩ 06216-006 06216-010 SDIO/DCS Figure 10. Equivalent Sense Circuit Figure 6. Equivalent SDIO/DCS Input Circuit DRVDD AVDD 6kΩ 06216-007 DRGND 06216-011 VREF Figure 11. Equivalent VREF Circuit Figure 7. Equivalent Digital Output Circuit Rev. 0 | Page 9 of 40 AD9254 TYPICAL PERFORMANCE CHARACTERISTICS AVDD = 1.8 V; DRVDD = 2.5 V; maximum sample rate, DCS enabled, 1 V internal reference; 2 V p-p differential input; AIN = −1.0 dBFS; 64k sample; TA = 25°C, unless otherwise noted. 0 –40 –60 –80 –40 –60 –80 –100 18.75 37.50 56.25 75.00 FREQUENCY (MHz) –120 06216-012 0 –60 –80 –40 –60 –80 –100 18.75 37.50 56.25 75.00 –120 06216-013 0 FREQUENCY (MHz) 0 18.75 37.50 56.25 75.00 Figure 16. AD9254 Single-Tone FFT with fIN = 140.3 MHz 0 150MSPS 70.3MHz @ –1dBFS SNR = 71.8dBc (72.8dBFS) ENOB = 11.7 BITS SFDR = 84dBc 150MSPS 170.3MHz @ –1dBFS SNR = 70.8dBc (71.8dBFS) ENOB = 11.5 BITS SFDR = 80dBc –20 AMPLITUDE (dBFS) –20 0 FREQUENCY (MHz) Figure 13. AD9254 Single-Tone FFT with fIN = 30.3 MHz –40 –60 –80 –40 –60 –80 –100 0 18.75 37.50 56.25 FREQUENCY (MHz) 75.00 Figure 14. AD9254 Single-Tone FFT with fIN = 70.3 MHz –120 0 18.75 37.50 56.25 75.00 FREQUENCY (MHz) Figure 17. AD9254 Single-Tone FFT with fIN = 170.3 MHz Rev. 0 | Page 10 of 40 06216-017 –100 06216-014 AMPLITUDE (dBFS) 75.00 06216-016 –100 –120 56.25 150MSPS 140.3MHz @ –1dBFS SNR = 71.5dBc (72.5dBFS) ENOB = 11.5 BITS SFDR = 81dBc –20 AMPLITUDE (dBFS) AMPLITUDE (dBFS) 0 –40 –120 37.50 Figure 15. AD9254 Single-Tone FFT with fIN = 100.3 MHz 150MSPS 30.3MHz @ –1dBFS SNR = 71.9dBc (72.9dBFS) ENOB = 11.7 BITS SFDR = 88dBc –20 18.75 FREQUENCY (MHz) Figure 12. AD9254 Single-Tone FFT with fIN = 2.3 MHz 0 0 06216-015 –100 –120 150MSPS 100.3MHz @ –1dBFS SNR = 71.6dBc (72.6dBFS) ENOB = 11.6 BITS SFDR = 83dBc –20 AMPLITUDE (dBFS) –20 AMPLITUDE (dBFS) 0 150MSPS 2.3MHz @ –1dBFS SNR = 72.0dBc (73.0dBFS) ENOB = 11.7 BITS SFDR = 90.0dBc AD9254 0 SFDR (dBFS) 100 SNR/SFDR (dBc and dBFS) –20 AMPLITUDE (dBFS) 120 150MSPS 250.3MHz @ –1dBFS SNR = 69.3dBc (70.3dBFS) ENOB = 11.3 BITS SFDR = 79dBc –40 –60 –80 –100 80 SNR (dBFS) 60 40 SFDR (dBc) 85dBc REFERENCE LINE 20 37.50 56.25 75.00 FREQUENCY (MHz) SFDR/WORST IMD3 (dBc and dBFS) AMPLITUDE (dBFS) –60 –80 18.75 37.50 56.25 75.00 FREQUENCY (MHz) –40 –30 –20 –10 0 –20 SFDR (–dBc) –40 WORST IMD3 (dBc) –60 –80 SFDR (–dBFS) –100 –120 –90 06216-019 –100 0 –50 0 –40 –120 –60 Figure 21. AD9254 Single-Tone SNR/SFDR vs. Input Amplitude (AIN) with fIN = 2.4 MHz 150MSPS fIN1 = 29.1MHz @ –7dBFS fIN2 = 32.1MHz @ –7dBFS SFDR = 83.2dBc (90.2dBFS) WoIMD3 = –83.9dBc (–90.9dBFS) –20 –70 INPUT AMPLITUDE (dBFS) Figure 18. AD9254 Single-Tone FFT with fIN = 250.3 MHz 0 –80 WORST IMD3 (dBFS) –78 –66 –54 –42 –30 –18 06216-022 18.75 06216-018 0 0 –90 06216-021 SNR (dBc) –120 –6 INPUT AMPLITUDE (dBFS) Figure 22. AD9254 Two-Tone SFDR/IMD3 vs. Input Amplitude (AIN) with fIN1 = 29.1 MHz, fIN2 = 32.1 MHz Figure 19. AD9254 Two-Tone FFT with fIN1 = 29.1 MHz, fIN2 = 32.1 MHz 90 90 SFDR +25°C SFDR –40°C SFDR –40°C 85 85 SNR/SFDR (dBc) 75 SNR –40°C SFDR +85°C 65 60 SNR +25°C 0 50 100 150 200 250 300 INPUT FREQUENCY (MHz) 80 SFDR +85°C 75 70 SNR +25°C SNR –40°C 65 SNR +85°C 350 400 60 Figure 20. AD9254 Single-Tone SNR/SFDR vs. Input Frequency (fIN) and Temperature with 2 V p-p Full Scale SNR +85°C 0 50 100 150 200 250 300 INPUT FREQUENCY (MHz) 350 400 06216-023 70 06216-020 SNR/SFDR (dBc) SFDR +25°C 80 Figure 23. AD9254 Single-Tone SNR/SFDR vs. Input Frequency (fIN) and Temperature with 1 V p-p Full Scale Rev. 0 | Page 11 of 40 AD9254 2.0 0 150MSPS fIN1 = 169.1MHz @ –7dBFS fIN2 = 172.1MHz @ –7dBFS SFDR = 83dBc (90dBFS) WoIMD3 = –83dBc (90dBFS) AMPLITUDE (dBFS) –20 1.5 1.0 INL ERROR (LSB) –40 –60 –80 0.5 0 –0.5 –1.0 –100 18.75 37.50 56.25 75.00 FREQUENCY (MHz) –2.0 0 2048 4096 6144 8192 10240 12288 14336 16384 OUTPUT CODE 06216-031 0 06216-024 –120 –1.5 Figure 27. AD9254 INL with fIN = 10.3 MHz Figure 24. AD9254 Two-Tone FFT with fIN1 = 169.1 MHz, fIN2 = 172.1 MHz 12000 95 32768 SAMPLES 1.25 LSB rms 10000 90 85 NUMBER OF HITS SNR/SFDR (dBc) SFDR 80 75 8000 6000 4000 SNR 20 30 40 50 60 70 80 90 100 110 120 130 140 150 CLOCK FREQUENCY (MSPS) 0 06216-025 65 10 N–5N–4N–3N–2N–1 N+1N+2N+3N+4N+5 Figure 28. AD9254 Grounded Input Histogram Figure 25. AD9254 Single-Tone SNR/SFDR vs. Clock Frequency (fCLK) with fIN = 2.4 MHz 0 0 OFFSET ERROR –20 –0.5 SFDR (–dBc) –40 ERROR (%FS) SFDR/WORST IMD3 (dBc and dBFS) N CODE 06216-032 2000 70 WORST IMD3 (dBc) –60 –1.0 –1.5 –80 GAIN ERROR SFDR (–dBFS) –2.0 –100 –66 –54 –42 –30 –18 –6 INPUT AMPLITUDE (dBFS) –2.5 –40 –20 0 20 40 60 TEMPERATURE (°C) Figure 29. AD9254 Gain and Offset vs. Temperature Figure 26. AD9254 Two-Tone SFDR/IMD3 vs. Input Amplitude (AIN) with fIN1 = 169.1 MHz, fIN2 = 172.11 MHz Rev. 0 | Page 12 of 40 80 06216-033 –78 06216-027 WORST IMD3 (dBFS) –120 –90 AD9254 0.5 0.4 0.2 0.1 0 –0.1 –0.2 –0.3 –0.4 –0.5 0 2048 4096 6144 8192 10240 12288 14336 OTUPUT CODE 16384 06216-034 DNL ERROR (LSB) 0.3 Figure 30. AD9254 DNL with fIN = 10.3 MHz Rev. 0 | Page 13 of 40 AD9254 THEORY OF OPERATION S The AD9254 architecture consists of a front-end sample-andhold amplifier (SHA) followed by a pipelined switched capacitor ADC. The quantized outputs from each stage are combined into a final 14-bit result in the digital correction logic. The pipeline architecture permits the first stage to operate on a new input sample, while the remaining stages operate on preceding samples. Sampling occurs on the rising edge of the clock. The input stage contains a differential SHA that can be ac- or dc-coupled in differential or single-ended modes. The output staging block aligns the data, carries out the error correction, and passes the data to the output buffers. The output buffers are powered from a separate supply, allowing adjustment of the output voltage swing. During power-down, the output buffers go into a high impedance state. ANALOG INPUT CONSIDERATIONS The analog input to the AD9254 is a differential switched capacitor SHA that has been designed for optimum performance while processing a differential input signal. CS VIN+ CPIN, PAR S H CS VIN– CH CPIN, PAR S 06216-035 Each stage of the pipeline, excluding the last, consists of a low resolution flash ADC connected to a switched capacitor DAC and interstage residue amplifier (MDAC). The residue amplifier magnifies the difference between the reconstructed DAC output and the flash input for the next stage in the pipeline. One bit of redundancy is used in each stage to facilitate digital correction of flash errors. The last stage consists only of a flash ADC. CH S Figure 31. Switched-Capacitor SHA Input For best dynamic performance, the source impedances driving VIN+ and VIN− should match such that common-mode settling errors are symmetrical. These errors are reduced by the common-mode rejection of the ADC. An internal differential reference buffer creates two reference voltages used to define the input span of the ADC core. The span of the ADC core is set by the buffer to be 2 × VREF. The reference voltages are not available to the user. Two bypass points, REFT and REFB, are brought out for decoupling to reduce the noise contributed by the internal reference buffer. It is recommended that REFT be decoupled to REFB by a 0.1 μF capacitor, as described in the Layout Considerations section. Input Common Mode The clock signal alternately switches the SHA between sample mode and hold mode (see Figure 31). When the SHA is switched into sample mode, the signal source must be capable of charging the sample capacitors and settling within one-half of a clock cycle. A small resistor in series with each input can help reduce the peak transient current required from the output stage of the driving source. A shunt capacitor can be placed across the inputs to provide dynamic charging currents. This passive network creates a lowpass filter at the ADC input; therefore, the precise values are dependent upon the application. The analog inputs of the AD9254 are not internally dc-biased. In ac-coupled applications, the user must provide this bias externally. Setting the device such that VCM = 0.55 × AVDD is recommended for optimum performance; however, the device functions over a wider range with reasonable performance (see Figure 30). An on-board common-mode voltage reference is included in the design and is available from the CML pin. Optimum performance is achieved when the common-mode voltage of the analog input is set by the CML pin voltage (typically 0.55 × AVDD). The CML pin must be decoupled to ground by a 0.1 μF capacitor, as described in the Layout Considerations section. In IF undersampling applications, any shunt capacitors should be reduced. In combination with the driving source impedance, these capacitors would limit the input bandwidth. For more information, see Application Note AN-742, Frequency Domain Response of Switched-Capacitor ADCs; Application Note AN-827, A Resonant Approach to Interfacing Amplifiers to SwitchedCapacitor ADCs; and the Analog Dialogue article, “TransformerCoupled Front-End for Wideband A/D Converters.” Rev. 0 | Page 14 of 40 AD9254 DIFFERENTIAL INPUT CONFIGURATIONS Optimum performance is achieved by driving the AD9254 in a differential input configuration. For baseband applications, the AD8138 differential driver provides excellent performance and a flexible interface to the ADC. The output common-mode voltage of the AD8138 is easily set with the CML pin of the AD9254 (see Figure 32), and the driver can be configured in a Sallen-Key filter topology to provide band limiting of the input signal. Table 8. RC Network Recommended Values 499Ω R VIN+ 499Ω 523Ω R AVDD AD9254 C AD8138 0.1µF CML VIN– 499Ω VIN+ R 10µF AD9254 VIN– R CML 0.1µF AVDD 1kΩ 1V p-p 06216-037 C C Differential (pF) 15 5 5 Open In this configuration, SFDR and distortion performance degrade due to the large input common-mode swing. If the source impedances on each input are matched, there should be little effect on SNR performance. Figure 34 details a typical single-ended input configuration. The signal characteristics must be considered when selecting a transformer. Most RF transformers saturate at frequencies below a few megahertz, and excessive signal power can cause core saturation, which leads to distortion. 49.9Ω R Series (Ω) 33 33 15 15 Although not recommended, it is possible to operate the AD9254 in a single-ended input configuration, as long as the input voltage swing is within the AVDD supply. Single-ended operation can provide adequate performance in cost-sensitive applications. For baseband applications where SNR is a key parameter, differential transformer coupling is the recommended input configuration (see Figure 33). The CML voltage can be connected to the center tap of the secondary winding of the transformer to bias the analog input. R Frequency Range (MHz) 0 to 70 70 to 200 200 to 300 >300 Single-Ended Input Configuration Figure 32. Differential Input Configuration Using the AD8138 2V p-p In any configuration, the value of the shunt capacitor, C, is dependent on the input frequency and source impedance and may need to be reduced or removed. Table 8 displays recommended values to set the RC network. However, these values are dependent on the input signal and should only be used as a starting guide. 49.9Ω 0.1µF AVDD 1kΩ 10µF 0.1µF VIN+ 1kΩ C R AD9254 VIN– 1kΩ Figure 33. Differential Transformer-Coupled Configuration At input frequencies in the second Nyquist zone and above, the noise performance of most amplifiers is not adequate to achieve the true SNR performance of the AD9254. For applications where SNR is a key parameter, transformer coupling is the recommended input. For applications where SFDR is a key parameter, differential double balun coupling is the recommended input configuration (see Figure 35). Rev. 0 | Page 15 of 40 Figure 34. Single-Ended Input Configuration 06216-038 49.9Ω 06216-036 1V p-p As an alternative to using a transformer-coupled input at frequencies in the second Nyquist zone, the AD8352 differential driver can be used (see Figure 36). AD9254 0.1µF 0.1µF R VIN+ 2V p-p 25Ω S S P 0.1µF 25Ω AD9254 C 0.1µF R 06216-039 PA CML VIN– Figure 35. Differential Double Balun Input Configuration VCC 0.1µF 0Ω 16 8, 13 1 0.1µF 11 R 2 VIN+ 200Ω CD RD AD8352 RG 3 0.1µF 10 200Ω 4 5 0.1µF 0Ω AD9254 C R VIN– CML 14 0.1µF 0.1µF 06216-040 0.1µF Figure 36. Differential Input Configuration Using the AD8352 Table 9. Reference Configuration Summary Selected Mode External Reference Internal Fixed Reference Programmable Reference SENSE Voltage AVDD VREF 0.2 V to VREF Resulting VREF (V) N/A 0.5 Internal Fixed Reference AGND to 0.2 V 1.0 R2 ⎞ 0.5 × ⎛⎜1 + ⎟ (see Figure 38) ⎝ R1 ⎠ VOLTAGE REFERENCE A stable and accurate voltage reference is built into the AD9254. The input range is adjustable by varying the reference voltage applied to the AD9254, using either the internal reference or an externally applied reference voltage. The input span of the ADC tracks reference voltage changes linearly. The various reference modes are summarized in the following sections. The Reference Decoupling section describes the best practices and requirements for PCB layout of the reference. Internal Reference Connection A comparator within the AD9254 detects the potential at the SENSE pin and configures the reference into four possible states, as summarized in Table 9. If SENSE is grounded, the reference amplifier switch is connected to the internal resistor divider (see Figure 37), setting VREF to 1 V. Resulting Differential Span (V p-p) 2 × external reference 1.0 2 × VREF 2.0 Connecting the SENSE pin to VREF switches the reference amplifier input to the SENSE pin, completing the loop and providing a 0.5 V reference output. If a resistor divider is connected external to the chip, as shown in Figure 38, the switch sets to the SENSE pin. This puts the reference amplifier in a noninverting mode with the VREF output defined as R2 ⎞ VREF = 0.5 ⎛⎜1 + ⎟ R1 ⎠ ⎝ If the SENSE pin is connected to AVDD, the reference amplifier is disabled, and an external reference voltage can be applied to the VREF pin (see the External Reference Operation section). The input range of the ADC always equals twice the voltage at the reference pin for either an internal or an external reference. Rev. 0 | Page 16 of 40 AD9254 External Reference Operation – The use of an external reference may be necessary to enhance the gain accuracy of the ADC or improve thermal drift characteristics. Figure 40 shows the typical drift characteristics of the internal reference in both 1 V and 0.5 V modes. REFT 0.1µF REFB 10 VREF 0.1µF REFERENCE VOLTAGE ERROR (mV) 0.1µF SELECT LOGIC SENSE 06216-041 0.5V AD9254 ADC CORE VIN– 4 2 0 –40 – VIN+ VREF = 0.5V 6 – Figure 37. Internal Reference Configuration VREF = 1V 8 REFT –20 0 20 40 TEMPERATURE (°C) When the SENSE pin is tied to AVDD, the internal reference is disabled, allowing the use of an external reference. An internal resistor divider loads the external reference with an equivalent 6 kΩ load (see Figure 11). In addition, an internal buffer generates the positive and negative full-scale references for the ADC core. Therefore, the external reference must be limited to a maximum of 1 V. REFB VREF 0.1µF R2 SELECT LOGIC SENSE 06216-042 0.5V R1 AD9254 CLOCK INPUT CONSIDERATIONS Figure 38. Programmable Reference Configuration If the internal reference of the AD9254 is used to drive multiple converters to improve gain matching, the loading of the reference by the other converters must be considered. Figure 39 depicts how the internal reference voltage is affected by loading. For optimum performance, the AD9254 sample clock inputs (CLK+ and CLK−) should be clocked with a differential signal. The signal is typically ac-coupled into the CLK+ pin and the CLK− pin via a transformer or capacitors. These pins are biased internally (see Figure 5) and require no external bias. Clock Input Options 0 The AD9254 has a very flexible clock input structure. The clock input can be a CMOS, LVDS, LVPECL, or sine wave signal. Regardless of the type of signal used, the jitter of the clock source is of the most concern, as described in the Jitter Considerations section. VREF = 0.5V –0.25 VREF = 1V –0.50 –0.75 –1.00 –1.25 0 0.5 1.0 1.5 LOAD CURRENT (mA) Figure 39. VREF Accuracy vs. Load 2.0 06216-043 REFERENCE VOLTAGE ERROR (%) 80 Figure 40. Typical VREF Drift 0.1µF 0.1µF 60 06216-044 ADC CORE VIN– – VIN+ Figure 41 shows one preferred method for clocking the AD9254. A low jitter clock source is converted from singleended to a differential signal using an RF transformer. The back-to-back Schottky diodes across the transformer secondary limit clock excursions into the AD9254 to approximately 0.8 V p-p differential. This helps prevent the large voltage swings of the clock from feeding through to other portions of the AD9254, while preserving the fast rise and fall times of the signal, which are critical to a low jitter performance. Rev. 0 | Page 17 of 40 AD9254 50Ω 0.1µF CLOCK INPUT CLK+ ADC AD9254 100Ω 0.1µF 1kΩ OPTIONAL 0.1µF 100Ω AD951x CMOS DRIVER ADC AD9254 CLK– CLK– 06216-045 SCHOTTKY DIODES: HMS2812 0.1µF CLK+ 1kΩ 50Ω1 0.1µF 150Ω Figure 41. Transformer Coupled Differential Clock 39kΩ 06216-048 0.1µF CLOCK INPUT VCC MINI-CIRCUITS ADT1–1WT, 1:1Z 0.1µF XFMR RESISTOR IS OPTIONAL. Figure 44. Single-Ended 1.8 V CMOS Sample Clock If a low jitter clock source is not available, another option is to ac-couple a differential PECL signal to the sample clock input pins as shown in Figure 42. The AD9510/AD9511/AD9512/ AD9513/AD9514/AD9515 family of clock drivers offers excellent jitter performance. VCC 50Ω1 1kΩ AD951x CMOS DRIVER OPTIONAL 0.1µF 100Ω 1kΩ 0.1µF CLK+ ADC AD9254 CLK– 0.1µF CLOCK INPUT CLK+ 100Ω AD951x 0.1µF PECL DRIVER 0.1µF CLK 50Ω1 150Ω 240Ω 50Ω1 Figure 45. Single-Ended 3.3 V CMOS Sample Clock ADC AD9254 Clock Duty Cycle CLK– 240Ω 06216-046 CLOCK INPUT 150Ω RESISTOR IS OPTIONAL. 0.1µF CLK RESISTORS ARE OPTIONAL. Figure 42. Differential PECL Sample Clock A third option is to ac-couple a differential LVDS signal to the sample clock input pins, as shown in Figure 43. The AD9510/ AD9511/AD9512/AD9513/AD9514/AD9515 family of clock drivers offers excellent jitter performance. 0.1µF CLOCK INPUT AD951x 0.1µF LVDS DRIVER 0.1µF CLK 50Ω1 ADC AD9254 CLK– 50Ω1 150Ω RESISTORS ARE OPTIONAL. 06216-047 CLOCK INPUT CLK+ 100Ω Typical high speed ADCs use both clock edges to generate a variety of internal timing signals. As a result, these ADCs may be sensitive to clock duty cycle. Commonly, a ±5% tolerance is required on the clock duty cycle to maintain dynamic performance characteristics. The AD9254 contains a duty cycle stabilizer (DCS) that retimes the nonsampling, or falling edge, providing an internal clock signal with a nominal 50% duty cycle. This allows a wide range of clock input duty cycles without affecting the performance of the AD9254. Noise and distortion performance are nearly flat for a wide range of duty cycles when the DCS is on, as shown in Figure 28. 0.1µF CLK 06216-049 CLOCK INPUT 0.1µF Figure 43. Differential LVDS Sample Clock In some applications, it is acceptable to drive the sample clock inputs with a single-ended CMOS signal. In such applications, directly drive CLK+ from a CMOS gate, while bypassing the CLK− pin to ground using a 0.1 μF capacitor in parallel with a 39 kΩ resistor (see Figure 44). CLK+ can be directly driven from a CMOS gate. This input is designed to withstand input voltages up to 3.6 V, making the selection of the drive logic voltage very flexible. When driving CLK+ with a 1.8 V CMOS signal, biasing the CLK− pin with a 0.1 μF capacitor in parallel with a 39 kΩ resistor (see Figure 44) is required. The 39 kΩ resistor is not required when driving CLK+ with a 3.3 V CMOS signal (see Figure 45). Jitter in the rising edge of the input is still of paramount concern and is not reduced by the internal stabilization circuit. The duty cycle control loop does not function for clock rates less than 20 MHz nominally. The loop has a time constant associated with it that needs to be considered in applications where the clock rate can change dynamically. This requires a wait time of 1.5 μs to 5 μs after a dynamic clock frequency increase (or decrease) before the DCS loop is relocked to the input signal. During the time period the loop is not locked, the DCS loop is bypassed, and the internal device timing is dependent on the duty cycle of the input clock signal. In such an application, it may be appropriate to disable the duty cycle stabilizer. In all other applications, enabling the DCS circuit is recommended to maximize ac performance. Rev. 0 | Page 18 of 40 AD9254 The DCS can be enabled or disabled by setting the SDIO/DCS pin when operating in the external pin mode (see Table 10), or via the SPI, as described in Table 13. Table 10. Mode Selection (External Pin Mode) Voltage at Pin AGND AVDD SCLK/DFS Binary (default) Twos complement SDIO/DCS DCS disabled DCS enabled (default) POWER DISSIPATION AND STANDBY MODE The power dissipated by the AD9254 is proportional to its sample rate (see Figure 47). The digital power dissipation is determined primarily by the strength of the digital drivers and the load on each output bit. Maximum DRVDD current (IDRVDD) can be calculated as I DRVDD = VDRVDD × CLOAD × fCLK ×N 2 where N is the number of output bits, 14 in the AD9254. JITTER CONSIDERATIONS High speed, high resolution ADCs are sensitive to the quality of the clock input. The degradation in SNR at a given input frequency (fIN) due to jitter (tJ) is calculated as follows: SNR = −20 log (2π × fIN × tJ) In the equation, the rms aperture jitter represents the root mean square of all jitter sources, which include the clock input, analog input signal, and ADC aperture jitter specification. IF undersampling applications are particularly sensitive to jitter, as shown in Figure 46. This maximum current occurs when every output bit switches on every clock cycle, that is, a full-scale square wave at the Nyquist frequency, fCLK/2. In practice, the DRVDD current is established by the average number of output bits switching, which is determined by the sample rate and the characteristics of the analog input signal. Reducing the capacitive load presented to the output drivers can minimize digital power consumption. The data in Figure 47 was taken under the same operating conditions as the data for the Typical Performance Characteristics section, with a 5 pF load on each output driver. 500 300 75 480 0.05ps 70 440 60 0.5ps 55 50 380 340 2.00ps 320 100 INPUT FREQUENCY (MHz) 100 50 I (DRVDD) 300 1000 06216-050 10 150 POWER 1.50ps 2.50ps 3.00ps 1 400 360 1.0ps 45 200 420 Figure 46. SNR vs. Input Frequency and Jitter 0 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 CLOCK FREQUENCY (MHz) 06216-051 POWER (mW) SNR (dBc) 0.20ps CURRENT (mA) I (AVDD) 65 40 250 460 MEASURED PERFORMANCE Figure 47. AD9254 Power and Current vs. Clock Frequency fIN = 30 MHz Power-Down Mode Treat the clock input as an analog signal in cases where aperture jitter can affect the dynamic range of the AD9254. Power supplies for clock drivers should be separated from the ADC output driver supplies to avoid modulating the clock signal with digital noise. The power supplies should also not be shared with analog input circuits, such as buffers, to avoid the clock modulating onto the input signal or vice versa. Low jitter, crystal-controlled oscillators make the best clock sources. If the clock is generated from another type of source (by gating, dividing, or other methods), it should be retimed by the original clock at the last step. Refer to Application Notes AN-501, Aperture Uncertainty and ADC System Performance; and AN-756, Sampled Systems and the Effects of Clock Phase Noise and Jitter, for more in-depth information about jitter performance as it relates to ADCs. By asserting the PDWN pin high, the AD9254 is placed in powerdown mode. In this state, the ADC typically dissipates 1.8 mW. During power-down, the output drivers are placed in a high impedance state. Reasserting the PDWN pin low returns the AD9254 to its normal operational mode. This pin is both 1.8 V and 3.3 V tolerant. Low power dissipation in power-down mode is achieved by shutting down the reference, reference buffer, biasing networks, and clock. The decoupling capacitors on REFT and REFB are discharged when entering power-down mode and then must be recharged when returning to normal operation. As a result, the wake-up time is related to the time spent in power-down mode; and shorter power-down cycles result in proportionally shorter wake-up times. With the recommended 0.1 μF decoupling capacitors on REFT and REFB, it takes approximately 0.25 ms to fully discharge the reference buffer decoupling capacitors and 0.35 ms to restore full operation. Rev. 0 | Page 19 of 40 AD9254 Standby Mode When using the SPI port interface, the user can place the ADC in power-down or standby modes. Standby mode allows the user to keep the internal reference circuitry powered when faster wake-up times are required (see the Memory Map section). By logically AND’ing the OR bit with the MSB and its complement, overrange high or underrange low conditions can be detected. Table 11 is a truth table for the overrange/underrange circuit in Figure 49, which uses NAND gates. MSB DIGITAL OUTPUTS The output data format can be selected for either offset binary or twos complement by setting the SCLK/DFS pin when operating in the external pin mode (see Table 10). As detailed in the Interfacing to High Speed ADCs via SPI user manual, the data format can be selected for either offset binary, twos complement, or Gray code when using the SPI control. Out-of-Range (OR) Condition An out-of-range condition exists when the analog input voltage is beyond the input range of the ADC. OR is a digital output that is updated along with the data output corresponding to the particular sampled input voltage. Thus, OR has the same pipeline latency as the digital data. +FS – 1 LSB OR +FS +FS – 1/2 LSB 06216-052 00 0000 0000 0001 00 0000 0000 0000 00 0000 0000 0000 –FS –FS – 1/2 LSB Figure 49. Overrange/Underrange Logic Table 11. Overrange/Underrange Truth Table OR 0 0 1 1 MSB 0 1 0 1 Analog Input Is: Within range Within range Underrange Overrange Digital Output Enable Function (OEB) The AD9254 has three-state ability. If the OEB pin is low, the output data drivers are enabled. If the OEB pin is high, the output data drivers are placed in a high impedance state. This is not intended for rapid access to the data bus. Note that OEB is referenced to the digital supplies (DRVDD) and should not exceed that supply voltage. TIMING The lowest typical conversion rate of the AD9254 is 10 MSPS. At clock rates below 10 MSPS, dynamic performance can degrade. The AD9254 provides latched data outputs with a pipeline delay of twelve clock cycles. Data outputs are available one propagation delay (tPD) after the rising edge of the clock signal. The length of the output data lines and the loads placed on them should be minimized to reduce transients within the AD9254. These transients can degrade the dynamic performance of the converter. –FS + 1/2 LSB 0 0 1 UNDER = 1 MSB 06216-053 The AD9254 output drivers can be configured to interface with 1.8 V to 3.3 V logic families by matching DRVDD to the digital supply of the interfaced logic. The output drivers are sized to provide sufficient output current to drive a wide variety of logic families. However, large drive currents tend to cause current glitches on the supplies that may affect converter performance. Applications requiring the ADC to drive large capacitive loads or large fan-outs may require external buffers or latches. OR DATA OUTPUTS 1 11 1111 1111 1111 0 11 1111 1111 1111 0 11 1111 1111 1110 OVER = 1 OR Data Clock Output (DCO) Figure 48. OR Relation to Input Voltage and Output Data OR is low when the analog input voltage is within the analog input range and high when the analog input voltage exceeds the input range, as shown in Figure 48. OR remains high until the analog input returns to within the input range and another conversion is completed. The AD9254 also provides data clock output (DCO) intended for capturing the data in an external register. The data outputs are valid on the rising edge of DCO, unless the DCO clock polarity has been changed via the SPI. See Figure 2 for a graphical timing description. Table 12. Output Data Format Input (V) VIN+ – VIN– VIN+ – VIN– VIN+ – VIN– VIN+ – VIN– VIN+ – VIN– Condition (V) < –VREF – 0.5 LSB = –VREF =0 = +VREF – 1.0 LSB > +VREF – 0.5 LSB Binary Output Mode 00 0000 0000 0000 00 0000 0000 0000 10 0000 0000 0000 11 1111 1111 1111 11 1111 1111 1111 Twos Complement Mode 10 0000 0000 0000 10 0000 0000 0000 00 0000 0000 0000 01 1111 1111 1111 01 1111 1111 1111 Rev. 0 | Page 20 of 40 Gray Code Mode (SPI Accessible) 11 0000 0000 0000 11 0000 0000 0000 00 0000 0000 0000 10 0000 0000 0000 10 0000 0000 0000 OR 1 0 0 0 1 AD9254 SERIAL PORT INTERFACE (SPI) The AD9254 serial port interface (SPI) allows the user to configure the converter for specific functions or operations through a structured register space provided inside the ADC. This provides the user added flexibility and customization depending on the application. Addresses are accessed via the serial port and may be written to or read from via the port. Memory is organized into bytes that are further divided into fields, as documented in the Memory Map section. For detailed operational information, see the Interfacing to High Speed ADCs via SPI user manual. CONFIGURATION USING THE SPI As summarized in Table 13, three pins define the SPI of this ADC. The SCLK/DFS pin synchronizes the read and write data presented to the ADC. The SDIO/DCS dual-purpose pin allows data to be sent to and read from the internal ADC memory map registers. The CSB pin is an active low control that enables or disables the read and write cycles. Table 13. Serial Port Interface Pins Pin Name SCLK/DFS SDIO/DCS CSB Function SCLK (serial clock) is the serial shift clock in. SCLK synchronizes serial interface reads and writes. SDIO (serial data input/output) is a dual-purpose pin. The typical role for this pin is an input and output, depending on the instruction being sent and the relative position in the timing frame. CSB (chip select bar) is an active-low control that gates the read and write cycles. The falling edge of the CSB in conjunction with the rising edge of the SCLK determines the start of the framing. Figure 50 and Table 14 provide examples of the serial timing and its definitions. Other modes involving the CSB are available. The CSB can be held low indefinitely to permanently enable the device (this is called streaming). The CSB can stall high between bytes to allow for additional external timing. When CSB is tied high, SPI functions are placed in a high impedance mode. This mode turns on any SPI pin secondary functions. During an instruction phase, a 16-bit instruction is transmitted. Data follows the instruction phase and the length is determined by the W0 bit and the W1 bit. All data is composed of 8-bit words. The first bit of each individual byte of serial data indicates whether a read or write command is issued. This allows the serial data input/output (SDIO) pin to change direction from an input to an output. In addition to word length, the instruction phase determines if the serial frame is a read or write operation, allowing the serial port to be used to both program the chip as well as read the contents of the on-chip memory. If the instruction is a readback operation, performing a readback causes the serial data input/output (SDIO) pin to change direction from an input to an output at the appropriate point in the serial frame. Data can be sent in MSB- or in LSB-first mode. MSB first is the default on power-up and can be changed via the configuration register. For more information, see the Interfacing to High Speed ADCs via SPI user manual. Table 14. SPI Timing Diagram Specifications Name tDS tDH tCLK tS tH tHI tLO Description Setup time between data and rising edge of SCLK Hold time between data and rising edge of SCLK Period of the clock Setup time between CSB and SCLK Hold time between CSB and SCLK Minimum period that SCLK should be in a logic high state Minimum period that SCLK should be in a logic low state HARDWARE INTERFACE The pins described in Table 13 comprise the physical interface between the user’s programming device and the serial port of the AD9254. The SCLK and CSB pins function as inputs when using the SPI interface. The SDIO pin is bidirectional, functioning as an input during write phases and as an output during readback. The SPI interface is flexible enough to be controlled by either PROM or PIC microcontrollers. This provides the user with the ability to use an alternate method to program the ADC. One method is described in detail in Application Note AN-812, Microcontroller-Based Serial Port Interface Boot Circuit. When the SPI interface is not used, some pins serve a dual function. When strapped to AVDD or ground during device power on, the pins are associated with a specific function. CONFIGURATION WITHOUT THE SPI In applications that do not interface to the SPI control registers, the SDIO/DCS and SCLK/DFS pins serve as stand-alone CMOS-compatible control pins. When the device is powered up, it is assumed that the user intends to use the pins as static control lines for the output data format and duty cycle stabilizer (see Table 10). In this mode, the CSB chip select should be connected to AVDD, which disables the serial port interface. For more information, see the Interfacing to High Speed ADCs via SPI user manual. Rev. 0 | Page 21 of 40 AD9254 Default Values MEMORY MAP Coming out of reset, critical registers are loaded with default values. The default values for the registers are shown in Table 15. READING THE MEMORY MAP REGISTER TABLE Each row in the memory map register table has eight address locations. The memory map is roughly divided into three sections: the chip configuration registers map (Address 0x00 to Address 0x02), the device index and transfer registers map (Address 0xFF), and the ADC functions map (Address 0x08 to Address 0x18). Logic Levels An explanation of two registers follows: Table 15 displays the register address number in hexadecimal in the first column. The last column displays the default value for each hexadecimal address. The Bit 7 (MSB) column is the start of the default hexadecimal value given. For example, Hexadecimal Address 0x14, output_phase, has a hexadecimal default value of 0x00. This means Bit 3 = 0, Bit 2 = 0, Bit 1 = 1, and Bit 0 = 1 or 0011 in binary. This setting is the default output clock or DCO phase adjust option. The default value adjusts the DCO phase 90° relative to the nominal DCO edge and 180° relative to the data edge. For more information on this function, consult the Interfacing to High Speed ADCs via SPI user manual. tS • “Clear a bit” is synonymous with “Bit is set to Logic 0” or “Writing Logic 0 for the bit.” A list of features accessible via the SPI and a brief description of what the user can do with these features follows. These features are described in detail in the Interfacing to High Speed ADCs via SPI user manual. Locations marked as open are currently not supported for this device. When required, these locations should be written with 0s. Writing to these locations is required only when part of an address location is open (for example, Address 0x14). If the entire address location is open (Address 0x13), then the address location does not need to be written. tHI “Bit is set” is synonymous with “Bit is set to Logic 1” or “Writing Logic 1 for the bit.” SPI-Accessible Features Open Locations tDS • • Modes: Set either power-down or standby mode. • Clock: Access the DCS via the SPI. • Offset: Digitally adjust the converter offset. • Test I/O: Set test modes to have known data on output bits. • Output Mode: Setup outputs, vary the strength of the output drivers. • Output Phase: Set the output clock polarity. • VREF: Set the reference voltage. tCLK tDH tH tLO CSB SCLK DON’T CARE R/W W1 W0 A12 A11 A10 A9 A8 A7 D5 D4 D3 D2 D1 D0 DON’T CARE 06216-054 SDIO DON’T CARE DON’T CARE Figure 50. Serial Port Interface Timing Diagram Rev. 0 | Page 22 of 40 AD9254 MEMORY MAP REGISTER TABLE Table 15. Memory Map Register Addr. Bit 7 (Hex) Parameter Name (MSB) Chip Configuration Registers 00 chip_port_config 0 01 chip_id 02 chip_grade Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 LSB first 0 = Off (Default) 1 = On Soft reset 0 = Off (Default) 1 = On 1 1 Soft reset 0 = Off (Default) 1 = On LSB first 0 = Off (Default) 1 = On Bit 0 (LSB) Default Value (Hex) 0 0x18 8-bit Chip ID Bits 7:0 (AD9254 = 0x00), (default) Open Open Open Open Read only The nibbles should be mirrored. See the Interfacing to High Speed ADCs via SPI user manual. Default is unique chip ID, different for each device. Child ID used to differentiate speed grades. Child ID 0 = 150 MSPS Open Open Open Read only Open SW transfer 0x00 Synchronously transfers data from the master shift register to the slave. Determines various generic modes of chip operation. See the Power Device Index and Transfer Registers FF device_update Open Open Open Open Open Open Global ADC Functions 08 modes Open PDWN 0—Full 1— Standby Open Open Internal power-down mode 000—normal (power-up) 001—full power-down 010—standby 011—normal (power-up) Note: External PDWN pin overrides this setting. 0x00 Open 0x01 Open Default Notes/ Comments Dissipation and Standby Mode and the SPIAccessible Features sections. 09 clock Open Open Open Open Open Rev. 0 | Page 23 of 40 Open Duty cycle stabilizer 0— disabled 1— enabled See the Clock Duty Cycle section and the SPI-Accessible Features section. AD9254 Addr. Bit 7 (Hex) Parameter Name (MSB) Flexible ADC Functions 10 offset Bit 6 Bit 5 test_io 14 output_mode Output Driver Configuration 00 for DRVDD = 2.5 V to 3.3 V 10 for DRVDD = 1.8 V Open 16 output_phase Open Output Clock Polarity 1 = inverted 0 = normal (Default) Internal Reference Resistor Divider 00—VREF = 1.25 V 01—VREF = 1.5 V 10—VREF = 1.75 V 11—VREF = 2.00 V (Default) Open 1 VREF Bit 3 Output Disable 1— disabled 0— enabled 1 Open Bit 2 Bit 1 Offset in LSBs +31 +30 +29 Digital Offset Adjust<5:0> 011111 011110 011101 … 000010 000001 000000 111111 111110 111101 ... 100001 100000 PN9 PN23 0 = normal 0 = normal (Default) (Default) 1 = reset 1 = reset 0D 18 Bit 4 Bit 0 (LSB) Default Value (Hex) Default Notes/ Comments 0x00 Adjustable for offset inherent in the converter. See SPIAccessible Features +2 +1 0 (Default) 1 −2 −3 Open Open section. −31 −32 Global Output Test Options 000—off 001—midscale short 010—+FS short 011—−FS short 100—checker board output 101—PN 23 sequence 110—PN 9 111—one/zero word toggle Data Format Select Output 00—offset binary Data (default) Invert 01—twos 1= complement invert 10—Gray Code Open Open Open 0x00 See the Interfacing to High Speed ADCs via SPI user manual. 0x00 Configures the outputs and the format of the data. 0x00 See the SPIAccessible Features section. Open Open Open Open Open Open 0xC0 See the SPIAccessible Features section. External output enable (OEB) pin must be high. Rev. 0 | Page 24 of 40 AD9254 LAYOUT CONSIDERATIONS SILKSCREEN PARTITION PIN 1 INDICATOR When connecting power to the AD9254, it is recommended that two separate supplies be used: one for analog (AVDD, 1.8 V nominal) and one for digital (DRVDD, 1.8 V to 3.3 V nominal). If only a single 1.8 V supply is available, it is routed to AVDD first, then tapped off and isolated with a ferrite bead or filter choke with decoupling capacitors proceeding connection to DRVDD. The user can employ several different decoupling capacitors to cover both high and low frequencies. These should be located close to the point of entry at the PC board level and close to the parts with minimal trace length. A single PC board ground plane is sufficient when using the AD9254. With proper decoupling and smart partitioning of analog, digital, and clock sections of the PC board, optimum performance is easily achieved. Exposed Paddle Thermal Heat Slug Recommendations It is required that the exposed paddle on the underside of the ADC be connected to analog ground (AGND) to achieve the best electrical and thermal performance of the AD9254. An exposed, continuous copper plane on the PCB should mate to the AD9254 exposed paddle, Pin 0. The copper plane should have several vias to achieve the lowest possible resistive thermal path for heat dissipation to flow through the bottom of the PCB. These vias should be solder-filled or plugged. To maximize the coverage and adhesion between the ADC and PCB, partition the continuous plane by overlaying a silkscreen on the PCB into several uniform sections. This provides several tie points between the two during the reflow process. Using one continuous plane with no partitions guarantees only one tie point between the ADC and PCB. See Figure 51 for a PCB layout example. For detailed information on packaging and the PCB layout of chip scale packages, see Application Note AN-772, A Design and Manufacturing Guide for the Lead Frame Chip Scale Package. 06216-055 POWER AND GROUND RECOMMENDATIONS Figure 51. Typical PCB Layout CML The CML pin should be decoupled to ground with a 0.1 μF capacitor, as shown in Figure 33. RBIAS The AD9254 requires the user to place a 10 kΩ resistor between the RBIAS pin and ground. This resister sets the master current reference of the ADC core and should have at least a 1% tolerance. REFERENCE DECOUPLING The VREF pin should be externally decoupled to ground with a low ESR 1.0 μF capacitor in parallel with a 0.1 μF ceramic low ESR capacitor. In all reference configurations, REFT and REFB are bypass points provided for reducing the noise contributed by the internal reference buffer. It is recommended that an external 0.1 μF ceramic capacitor be placed across REFT/REFB. While placement of this 0.1 μF capacitor is not required, the SNR performance degrades by approximately 0.1 dB without it. All reference decoupling capacitors should be placed as close to the ADC as possible with minimal trace lengths. Rev. 0 | Page 25 of 40 AD9254 EVALUATION BOARD The AD9254 evaluation board provides all of the support circuitry required to operate the ADC in its various modes and configurations. The converter can be driven differentially through a double balun configuration (default) or through the AD8352 differential driver. The ADC can also be driven in a single-ended fashion. Separate power pins are provided to isolate the DUT from the AD8352 drive circuitry. Each input configuration can be selected by proper connection of various components (see Figure 53 to Figure 63). Figure 52 shows the typical bench characterization setup used to evaluate the ac performance of the AD9254. When operating the evaluation board in a nondefault condition, L501, L503, L504, L508, and L509 can be removed to disconnect the switching power supply. This enables the user to individually bias each section of the board. Use P501 to connect a different supply for each section. At least one 1.8 V supply is needed with a 1 A current capability for AVDD_DUT and DRVDD_DUT; however, it is recommended that separate supplies be used for analog and digital. To operate the evaluation board using the AD8352 option, a separate 5.0 V supply (AMP_VDD) with a 1 A current capability is needed. To operate the evaluation board using the alternate SPI options, a separate 3.3 V analog supply is needed, in addition to the other supplies. The 3.3 V supply (AVDD_3.3V) should have a 1 A current capability as well. Solder Jumpers J501, J502, and J505 allow the user to combine these supplies (see Figure 57 for more details). It is critical that the signal sources used for the analog input and clock have very low phase noise (<1 ps rms jitter) to realize the optimum performance of the converter. Proper filtering of the analog input signal to remove harmonics and lower the integrated or broadband noise at the input is also necessary to achieve the specified noise performance. INPUT SIGNALS When connecting the clock and analog source, use clean signal generators with low phase noise, such as Rohde & Schwarz SMHU or Agilent HP8644 signal generators or the equivalent. Use one meter long, shielded, RG-58, 50 Ω coaxial cable for making connections to the evaluation board. Enter the desired frequency and amplitude for the ADC. Typically, most evaluation boards from Analog Devices, Inc. can accept a ~2.8 V p-p or 13 dBm sine wave input for the clock. When connecting the analog input source, it is recommended to use a multipole, narrowband, band-pass filter with 50 Ω terminations. Analog Devices uses TTE®, Allen Avionics, and K&L® types of band-pass filters. Connect the filter directly to the evaluation board, if possible. See Figure 53 to Figure 57 for the complete schematics and layout diagrams that demonstrate the routing and grounding techniques that should be applied at the system level. POWER SUPPLIES This evaluation board comes with a wall-mountable switching power supply that provides a 6 V, 2 A maximum output. Connect the supply to the rated 100 V ac to 240 V ac wall outlet at 47 Hz to 63 Hz. The other end is a 2.1 mm inner diameter jack that connects to the PCB at P500. Once on the PC board, the 6 V supply is fused and conditioned before connecting to five low dropout linear regulators that supply the proper bias to each of the various sections on the board. OUTPUT SIGNALS The parallel CMOS outputs interface directly with the Analog Devices standard single-channel FIFO data capture board (HSC-ADC-EVALB-SC). For more information on the FIFO boards and their optional settings, visit www.analog.com/FIFO. WALL OUTLET 100V TO 240V AC 47Hz TO 63Hz AIN 3.3V + – + – + VDL GND AVDD_3.3V GND VCC 3.3V – GND 3.3V + DRVDD_DUT GND 2.5V – GND – AD9254 EVALUATION BOARD CLK 14-BIT PARALLEL CMOS SPI Figure 52. Evaluation Board Connection Rev. 0 | Page 26 of 40 HSC-ADC-EVALB-SC FIFO DATA CAPTURE BOARD USB CONNECTION SPI PC RUNNING ADC ANALYZER AND SPI USER SOFTWARE SPI 06216-056 ROHDE & SCHWARZ, SMHU, 2V p-p SIGNAL SYNTHESIZER BAND-PASS FILTER + AMP_VDD ROHDE & SCHWARZ, SMHU, 2V p-p SIGNAL SYNTHESIZER 1.8V + – GND 5.0V SWITCHING POWER SUPPLY AVDD_DUT 6V DC 2A MAX AD9254 DEFAULT OPERATION AND JUMPER SELECTION SETTINGS The following is a list of the default and optional settings or modes allowed on the AD9254 Rev. A evaluation board. POWER Connect the switching power supply that is supplied in the evaluation kit between a rated 100 V ac to 240 V ac wall outlet at 47 Hz to 63 Hz and P500. VIN The evaluation board is set up for a double balun configuration analog input with optimum 50 Ω impedance matching out to 70 MHz. For more bandwidth response, the differential capacitor across the analog inputs can be changed or removed (see Table 8). The common mode of the analog inputs is developed from the center tap of the transformer via the CML pin of the ADC (see the Analog Input Considerations section). VREF VREF is set to 1.0 V by tying the SENSE pin to ground via JP507 (Pin 1 and Pin 2). This causes the ADC to operate in 2.0 V p-p full-scale range. A separate external reference option is also included on the evaluation board. Connect JP507 between Pin 2 and Pin 3, connect JP501, and provide an external reference at E500. Proper use of the VREF options is detailed in the Voltage Reference section. RBIAS RBIAS requires a 10 kΩ resistor (R503) to ground and is used to set the ADC core bias current. CLOCK The default clock input circuitry is derived from a simple transformer-coupled circuit using a high bandwidth 1:1 impedance ratio transformer (T503) that adds a very low amount of jitter to the clock path. The clock input is 50 Ω terminated and ac-coupled to handle single-ended sine wave inputs. The transformer converts the single-ended input to a differential signal that is clipped before entering the ADC clock inputs. PDWN To enable the power-down feature, connect JP506, shorting the PDWN pin to AVDD. CSB The CSB pin is internally pulled-up, setting the chip into external pin mode, to ignore the SDIO and SCLK information. To connect the control of the CSB pin to the SPI circuitry on the evaluation board, connect JP1 Pin 1 and Pin 2. To set the chip into serial pin mode, and enable the SPI information on the SDIO and SCLK pins, tie JP1 low (connect Pin 2 and Pin 3) in the always enabled mode. SCLK/DFS If the SPI port is in external pin mode, the SCLK/DFS pin sets the data format of the outputs. If the pin is left floating, the pin is internally pulled down, setting the default condition to binary. Connecting JP2 Pin 2 and Pin 3 sets the format to twos complement. If the SPI port is in serial pin mode, connecting JP2 Pin 1 and Pin 2 connects the SCLK pin to the on-board SPI circuitry (see the Serial Port Interface (SPI) section). SDIO/DCS If the SPI port is in external pin mode, the SDIO/DCS pin acts to set the duty cycle stabilizer. If the pin is left floating, the pin is internally pulled up, setting the default condition to DCS enabled. To disable the DCS, connect JP3 Pin 2 and Pin 3. If the SPI port is in serial pin mode, connecting JP3 Pin 1 and Pin 2 connects the SDIO pin to the on-board SPI circuitry (see the Serial Port Interface (SPI) section). ALTERNATIVE CLOCK CONFIGURATIONS A differential LVPECL clock can also be used to clock the ADC input using the AD9515 (U500). When using this drive option, the components listed in Table 16 need to be populated. Consult the AD9515 data sheet for further information. To configure the analog input to drive the AD9515 instead of the default transformer option, the following components need to be added, removed, and/or changed. 1. Remove R507, R508, C532, and C533 in the default clock path. 2. Populate R505 with a 0 Ω resistor and C531 in the default clock path. 3. Populate R511, R512, R513, R515 to R524, U500, R580, R582, R583, R584, C536, C537, and R586. If using an oscillator, two oscillator footprint options are also available (OSC500) to check the performance of the ADC. JP508 provides the user flexibility in using the enable pin, which is common on most oscillators. Populate OSC500, R575, R587, and R588 to use this option. ALTERNATIVE ANALOG INPUT DRIVE CONFIGURATION This section provides a brief description of the alternative analog input drive configuration using the AD8352. When using this particular drive option, some components need to be populated, as listed in Table 16. For more details on the AD8352 differential driver, including how it works and its optional pin settings, consult the AD8352 data sheet. Rev. 0 | Page 27 of 40 AD9254 Note that to terminate the input path, only one of the following components should be populated: R9, R592, or the combination of R590 and R591). To configure the analog input to drive the AD8352 instead of the default transformer option, the following components need to be added, removed, and/or changed: 1. Remove C1 and C2 in the default analog input path. 2. Populate R3 and R4 with 200 Ω resistors in the analog input path. 3. Populate the optional amplifier input path with all components except R594, R595, and C502. 4. Populate C529 with a 5 pF capacitor in the analog input path. Currently, R561 and R562 are populated with 0 Ω resistors to allow signal connection. This area allows the user to design a filter if additional requirements are necessary. Rev. 0 | Page 28 of 40 S504 Rev. 0 | Page 29 of 40 Figure 53. Evaluation Board Schematic, DUT Analog Inputs GND;3,4,5 SMA200UP R7 DNI R560 0 2 RC0603 2 RC0603 C528 0.1UF C3 DNI CML RC0402 R6 DNI RC0402 R2 0 R11 0 DNI R9 DNI 1 1 RC0603 2 R12 0 DNI RC0603 2 R10 0 DNI C4 0 C5 0 C509 .1UF 4 5 T500 S 4 5 P DNI S 4 5 2 3 6 1 T1 T502 DNI ETC1-1-13 P 3 2 1 3 2 1 CML RC0402 For amplifier (AD8352): Install all optional Amp input components. R590/R591,R9,R592 Only one should be installed at a time. Remove C1, C2. Set R3=R4=200 OHM. DNI DNI When using T502, remove T500, T501. Repalce C1, C2 with 0 ohm resistors. Remove R3, R4. Place R6, R502,. 1 GND;3,4,5 R8 DNI R502 50 DNI 1 RC060 3 06216-057 DNI Ampin/ S505 DNI SMA200UP GND;3,4,5 SMAEDGE GND;3,4,5 RC060 3 Ampin Ain/ S503 Ain SMAEDGE CC0402 CC0402 S500 RC060 3 CC0402 R590 25 DNI R591 25 DNI R1 DNI RC0402 R592 DNI S T501 P 5 C503 .1UF DNI C500 .1UF DNI R5 0 C2 .1UF AMPOUT- R565 DNI AMPOUT+ RC0402 R597 4.3K DNI R596 0 DNI DNI 2 1 4 RDP VIN RDN 5 16 VIP 2 15 U511 VCM 14 6 7 GND AMPVDD GND VON VCC 8 GND VOP VCC 13 AMPVDD AD8352 DNI SIGNAL=GND;17 ENB 3 disable R594 10K DNI J500 enable 1 RGP R598 100 RGN DNI 3 AMPVDD C501 0.3PF R593 0 DNI R4 25 R3 25 C510 .1UF 9 10 11 12 RC0402 R571 0 R595 10K DNI OPTIONAL AMP INPUT When using R1, remove R3, R4,R6. Replace R5 with 0.1UF cap Replace C1, C2 with 0 ohm resistors. 3 ETC1-1-13 4 2 1 C1 .1UF RC040 2 CC0402 RC040 2 RC0402 RC0402 RC0402 R536 R535 C502 .1UF DNI R562 0 CML R561 0 0 0 RC0402 DNI RC0402 DNI 1 D500 DNI R567 33 R566 33 3 VIN+ R574 DNI HSMS281 2 DOUBLE BALUN / XFMR INPUT RC0402 C505 .1UF DNI C504 .1UF DNI DUTAVDD 2 RC0402 RC0402 R563 DNI HSMS281 2 AMPOUT- 2 VIN- DUTAVDD C529 20PF D501 DNI AMPOUT+ 1 3 VIN- CC0402 VIN+ AD9254 SCHEMATICS RC060 3 TP500 TP504 D1 Rev. 0 | Page 30 of 40 E500 48 47 CC0402 E X T _V RE F 45 D0 46 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 DCO JP502 DNI CLK CLK JP506 DNI VIN- VIN+ CC0402 C554 0.1UF VREF SENSE DUTDRVDD DUTAVDD CC0603 R503 10K RC060 3 06216-058 C556 0.1UF CML DUT chip corners AVDD AGND AVDD AGND CSB SCLK/DFS SDIO/DCS DRVDD DRGND OR D13 (MSB) D12 C555 0.1UF DNI JP501 CC0805 DNI JP500 3 C553 1.0UF DUTAVDD 2 JP507 1 Figure 54. Evaluation Board Schematic, DUT, VREF, and Digital Output Interface R0402 DNI R501 VREF R0402 DNI R500 SEN SE AD9246LFCSP D11 AGND D10 CLK+ EPAD D9 CLKD8 AVDD AGND DRVDD AVDD DRGND D7 OEB DCO D6 D0 (LSB) D5 U510 D1 D4 D3 DRGND D2 DRVDD SENSE VREF REFB REFT AGND VIN+ VINAGND AVDD CML RBIAS PDWN 1 2 3 4 5 6 7 8 9 10 11 12 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 13 DOR 14 TP502 TP501 TP503 DUTDRVDD DUTAVDD 15 16 17 18 19 20 21 22 23 24 8 10 9 9 RP500 22 RP501 22 RP501 22 RP502 22 1 7 8 8 DCO D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 DOR 7 6 5 16 15 14 13 12 11 16 15 14 13 12 11 10 RP500 22 RP500 22 RP500 22 RP501 22 RP501 22 RP501 22 RP501 22 RP501 22 RP501 22 RP502 22 RP502 22 RP502 22 RP502 22 RP502 22 RP502 22 RP502 22 CSB_DUT 2 3 4 1 2 3 4 5 6 1 2 3 4 5 6 7 1 JP1 VDL 2 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 3 2 JP2 O10 O7 O6 I7 I6 O0 OUTPUT BUFFER OE1 I0 OE2 O1 I1 GND1 O2 I2 GND8 O3 VCC1 O4 O5 I3 VCC4 I4 I5 GND2 O8 I8 GND7 O9 I9 GND3 I10 GND6 O11 I11 VCC2 O12 I12 VCC3 O13 GND4 I13 GND5 O14 OE4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 SDIO_ODM O15 3 DUTAVDD I14 U509 74VCX16224 1 I15 OE3 SCLK_DTP 1 JP3 3 FDOR FD0 FD1 FD2 FD3 FD4 FD5 FD6 FD7 FD8 FD9 FD10 FD11 FD12 FD13 FIFOCLK FIFOCLK FD0 FD1 FD2 FD3 FD4 FD5 FD6 FD7 FD8 FD9 FD10 FD11 FD12 FD13 FDOR 2 J503 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 B17 B18 B19 B20 SCLK_CHA SDO_CHA CSB1_CHA SDI_CHA C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19 C20 J503 OUTPUT CONNECTOR J503 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 AD9254 06216-059 GND;3,4,5 CLK/ SMAEDGE S502 GND;3,4,5 CLK SMAEDGE S501 R505 49.9 DNI C530 0.1UF C531 0.1UF DNI CC0402 RC0402 OPT_CLK 1 1 OPT_CLK OPT_CLK OPT_CLK R504 49.9 CC0402 R575 0 DNI VCC R511 DNI 2 RC0603 2 RC0603 R579 DNI R510 DNI R512 0 RC0603 RC0603 R576 DNI R507 0 DNI 0 OE OE GND GND CB3LV-3C OUT R508 8 10 OUT 12 VCC 14 RC0402 RC0402 C511 .1UF R578 DNI R577 DNI R509 0 R506 0 RC0603 RC0603 D502 HSMS2812 2 1 3 C533 0.1UF C532 0.1UF CLK CLK E501 5 3 2 AD9515 RC0402 DNI OUT0B OUT0 NC=27,28 OUT1B OUT1 AVDD_3P3V;1,4,17,20,21,24,26,29,30 SYNCB CLKB CLK DNI U500 R586 4.12K 18 19 22 23 R584 240 DNI R585 100 DNI R583 240 DNI R582 100 DNI C536 0.1UF DNI C537 0.1UF DNI C534 0.1UF DNI C535 0.1UF DNI E503 E502 CLK CLK To use AD9515 (OPT _CLK), remove R507, R508, C533, C532. Place C531,R505=0. 4 6 3 R580 10K DNI T503 R588 10K DNI 5 1 2 1 AVDD_3P3V R581 DNI 7 5 3 1 2 RC0402 DNI RC0402 OSC500 S8 DISABLE S9 ENABLE S10 DNI JP508 VREF 6 S0 7 S1 8 S2 9 S3 10 S4 11 S5 12 S6 13 S7 14 Figure 55. Evaluation Board Schematic, DUT Clock Input 15 3 RSET 16 RC0402 RC0402 CC0402 CC0402 RC0402 10K DNI RC0402 R587 GN D 25 CC0402 RC0402 GND_PAD RC0402 32 CC0402 31 CC0402 AVDD_3P3V RC0402 RC0402 Rev. 0 | Page 31 of 40 33 CC0402 XFMR/AD9515 Clock Circuitry S10 S9 S8 S7 S6 S5 S4 S3 S2 S1 S0 R532 DNI R533 DNI R534 DNI R529 DNI R528 DNI R530 DNI R531 DNI R526 DNI R527 DNI R525 DNI 0 0 0 0 0 0 0 0 0 0 0 RC0603 RC0603 RC0603 RC0603 RC0603 RC0603 RC0603 RC0603 RC0603 RC0603 RC0603 R522 R523 R524 R519 R518 R520 R521 R516 R517 R515 R513 0 0 0 0 0 0 0 0 0 0 0 RC0603 DNI RC0603 DNI RC0603 DNI RC0603 DNI RC0603 DNI RC0603 DNI RC0603 DNI RC0603 DNI RC0603 DNI RC0603 DNI RC0603 DNI AD9515 LOGIC SETUP AVDD_3P3V R514 DNI AD9254 S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 S10 RC060 3 RC060 3 RC060 3 06216-060 2 1 S1 DNI 4 3 1 2 JP509 1 SOIC8 DNI GP1 GP0 VSS RC0603 2 2 1 GP1 3 GP0 5 MCLR-GP3 7 9 HEADER UP MALE DNI J504 E504 5 6 7 8 DNI MCLR GP2 PIC12F629 GP4 GP5 VDD U506 A M PVD D R559 D505 261 Optional DNI 4 3 2 1 DNI 3 PICVCC 1 Rev. 0 | Page 32 of 40 4 2 6 8 10 PICVCC GP1 GP0 MCLR-GP3 Figure 56. Evaluation Board Schematic, SPI Circuitry R547 4.7K DNI When using PICSPI controlled port, populate R545, R546, R547. When using PICSPI controlled port, remove R555, R556, R557. For FIFO controlled port, populate R555, R556, R557. PIC-HEADER DNI C557 CC0603 0.1UF DNI R558 4.7K A VD D _3 P3V +5V=PROGRAMMING ONLY=AMPVDD +3.3V=NORMAL OPERATION=AVDD_3P3V RC060 3 SPI CIRCUITRY R545 4.7K RC0603 DNI R546 4.7K RC0603 DNI RC0603 R555 0 R557 0 R556 0 R549 10K AVDD_3P3V R554 0 RC0603 RC0603 RC0603 RC0603 SCLK_CHA RC0603 SDI_CH A R548 10K R550 10K RC0603 RC0603 CSB1_CHA U508 6 Y1 5 VCC 4 Y2 6 Y1 5 VCC 4 Y2 NC7WZ16 1 A1 2 GND 3 A2 U507 NC7WZ07 1 A1 2 GND 3 A2 R552 1K R551 1K R553 1K DUTAVDD AVDD_3P3V RC0603 SDO_CHA RC0603 REMOVE WHEN USING OR PROGRAMMING PIC (U506) CSB_DUT SCLK_DTP SDIO_ODM AD9254 RC0603 Figure 57. Evaluation Board Schematic, Power Supply Inputs Rev. 0 | Page 33 of 40 DUTDRVDDIN GND 5 P5 6 P6 06216-061 J502 J501 J505 LC1210 L500 10UH LC1210 L506 10UH LC1210 L502 10UH LC1210 L507 10UH LC1210 L505 10UH D504 S2A_RECT 2A DO-214AA ACASE ACASE ACASE ACASE ACASE Remove L501,L503,L504,L508,L509. To use optional power connection GND GND AVDD_3P3VIN 9 P9 10 P10 8 P8 VDLIN GND AMPVDDIN DUTAVDDIN 7 P7 C527 10UF SMDC110F 4 FER500 CHOKE_COIL 3 C548 1OUF 6.3V C552 1OUF 6.3V C551 1OUF 6.3V C550 1OUF 6.3V C549 1OUF 6.3V C512 0.1UF AVDD_3P3V C517 0.1UF DUTDRVDD C516 0.1UF DUTAVDD C515 0.1UF VDL C514 0.1UF AMPVDD OPTIONAL POWER CONNECTION 4 P4 2 3 P3 3 GND 1 2 P2 P501 1 P1 7.5V POWER CON005 2.5MM JACK P500 F500 Power Supply Input 6V, 2A max DUTDRVDD DUTAVDD VDL AMPVDD PWR_IN CC0603 CC0603 CC0603 CC0603 C573 0.1UF C569 0.1UF C564 0.1UF C567 0.1UF R589 261 C572 0.1UF C575 0.1UF C565 0.1UF CC0603 CC0603 CC0603 CC0603 C524 1UF PWR_IN C521 1UF PWR_IN C519 1UF PWR_IN CC0603 C599 0.1UF CC0603 0.1UF C570 0.1UF 4 4 4 CC0603 2 OU TP UT1 OUTPUT4 CC0603 C559 CC0603 C566 0.1UF IN P U T C558 CC0603 2 OU TP UT1 OUTPUT4 U504 ADP3339AKC-3.3 IN P U T U503 ADP3339AKC-2.5 2 OU TP UT1 OUTPUT4 U502 ADP3339AKC-1.8 IN P U T 0.1UF C568 0.1UF 3 3 3 GND 1 GND 1 GND 1 C574 0.1UF CC0402 C540 0.1UF CC0402 C545 0.1UF VDLIN CC0402 CC0402 C513 1UF PWR_IN C523 1UF PWR_IN DUTDRVDDIN DUTAVDDIN TP508 TP505 AVDD_3P3V LC1210 L508 10UH LC1210 L503 10UH AVDD_3P3V C526 1UF C520 1UF C518 1UF L504 10UH LC1210 C539 0.1UF C544 0.1UF 3 3 O UTP UT 1 OUTPUT4 CC0402 CC0402 IN P U T C542 0.1UF C546 0.1UF CC0402 CC0402 C538 0.1UF C543 0.1UF O UTP UT 1 OUTPUT4 U505 ADP3339AKC-3.3 IN P U T U501 ADP3339AKC-5 DUTAVDD=1.8V DUTDRVDD=2.5V VDL=3.3V AMPVDD=5V AVDD_3.3V=3.3V GND 1 GND 1 TP506 2 2 LC1210 L509 10UH LC1210 L501 10UH C525 1UF C522 1UF TEST POINTS GROUND 4 4 TP510 2 TP512 CR500 TP509 1 TP511 D503 3A SHOT_RECT DO-214AB H503 H502 Connected to Ground Mounting Holes H500 H501 AVDD_3P3V AMPVDDIN TP513 TP507 AD9254 AD9254 06216-062 EVALUATION BOARD LAYOUT 06216-063 Figure 58. Evaluation Board Layout, Primary Side Figure 59. Evaluation Board Layout, Secondary Side (Mirrored Image) Rev. 0 | Page 34 of 40 06216-064 AD9254 06216-065 Figure 60. Evaluation Board Layout, Ground Plane Figure 61. Evaluation Board Layout, Power Plane Rev. 0 | Page 35 of 40 06216-066 AD9254 06216-067 Figure 62. Evaluation Board Layout, Silkscreen Primary Side Figure 63. Evaluation Board Layout, Silkscreen Secondary Side (Mirrored Image) Rev. 0 | Page 36 of 40 AD9254 BILL OF MATERIALS Table 16. Evaluation Board Bill of Materials (BOM) Item 1 2 Qty. 1 24 Omit (DNP) 12 1 2 Reference Designator AD9246CE_REVA C1, C2, C509, C510, C511, C512, C514, C515, C516, C517, C528, C530, C532, C533, C538, C539, C540, C542, C543, C544, C545, C546, C554, C555 C3, C500, C502, C503, C504, C505, C531, C534, C535, C536, C537, C557 C501 C4, C5 C513, C518, C519, C520, C521, C522, C523, C524, C525, C526 Device PCB Capacitor Package 0402 Description PCB 0.1 μF Capacitor Resistor Capacitor 0402 0402 0402 0.3 pF 0Ω 1.0 μF 3 4 5 10 6 7 8 9 10 1 1 5 1 15 C527 C529 C548, C549, C550, C551, C552 C553 C556, C558, C559, C564, C565, C566, C567, C568, C569, C570, C572, C573, C574, C575, C599 Capacitor Capacitor Capacitor Capacitor Capacitor 1206 0402 ACASE 0805 0603 10 μF 20 pF 10 μF 1.0 μF 0.1 μF 11 1 CR500 LED 0603 green 12 1 Diode SOT-23 30 V, 20 mA, dual Schottky Diode DO-214AB 3 A, 30 V, SMC 13 1 D502 D500, D501 D503 14 1 D504 Diode DO-214AA 2 A, 50 V, SMC 15 16 1 D505 F500 LED Fuse LN1461C 1210 AMB 6.0 V, 2.2 A trip current resettable fuse 17 1 FER500 Choke 2020 J500 J501, J502, J505 J503 J504 JP1, JP2, JP3 JP500, JP501, JP502, JP506 JP507 JP508, JP509 L500, L501, L502, L503, L504, L505, L506, L507, L508, L509 Jumper Jumper Connector Connector Jumper Jumper Jumper OSC500 Oscillator 3.2 mm × 2.5 mm × 1.6 mm SMT P500 Connector PJ-102A 2 18 19 20 21 22 23 24 1 1 3 1 1 3 4 1 2 25 10 26 27 1 1 Ferrite Bead Rev. 0 | Page 37 of 40 120 pin 10 pin 3 pin 2 pin 3-pin jumper Supplier/Part Number ADI Panasonic LNJ314G8TRA HSMS2812 Micro Commercial Components SK33TPMSCT-ND Micro Commercial Components S2ATPMSTR-ND Amber LED Tyco, Raychem NANOSMDC110F-2 Murata DLW5BSN191SQ2 Solder jumper Solder jumper Male header Male, 2 × 5 Male, straight Male, straight Male, straight Samtec TSW-140-08-G-T-RA Samtec Samtec TSW-103-07-G-S Samtec TSW-102-07-G-S Samtec TSW-103-07-G-S Digikey P9811CT-ND 125 MHz or 105 MHz DC power jack CTS Reeves CB3LV-3C Digikey CP-102A-ND AD9254 Item 28 29 30 Qty. Omit (DNP) 1 6 5 6 31 32 33 2 34 35 4 1 6 6 1 36 9 23 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 1 54 2 56 59 Resistor Resistor Resistor 0402 0603 0402 25 Ω DNI DNI Resistor Resistor 0603 0603 10 kΩ 49.9 Ω Resistor 0603 0Ω Resistor Resistor Resistor Resistor Resistor Resistor Resistor Resistor Resistor Resistor Resistor Resistor Resistor Resistor Resistor Resistor Switch 0603 0603 0603 0402 0402 0402 0402 0402 0603 0402 0402 0402 0402 0402 RCA74204 RCA74208 Connector SMAEDGE 4.7 kΩ 1 kΩ 261 Ω 33 Ω 100 Ω 240 Ω 4.12 kΩ 10 kΩ 261 Ω 25 Ω DNI 0Ω 10 kΩ 4.3 kΩ 22 Ω 22 Ω Momentary (normally open) SMA edge right angle Connector SMA200UP T500, T501 T1 T503 T502 U500 Transformer SM-22 M/A-Com ETC1-1-13 Transformer CD542 Mini-Circuits ADT1-1WT IC U501 IC 32-pin LFCSP _VQ SOT-223 S500, S501 S502, S503 S504, S505 2 3 2 1 3 2 1 2 2 1 1 2 2 1 1 1 1 Description Male, straight DNI 0Ω 2 2 1 58 Package 10 pin 0402 0402 1 4 1 57 Device Connector Resistor Resistor R507, R513, R514, R515, R516, R517, R518, R519, R520, R521, R522, R523, R524, R525, R526, R527, R528, R529, R530, R531, R532, R533, R534, R545, R546, R547, R558 R551, R552, R553 R559 R566, R567 R582, R585, R598 R583, R584 R586 R580, R587, R588 R589 R590, R591 R592 R593, R596 R594, R595 R597 RP500 RP501, RP502 S1 3 55 Reference Designator P501 R1, R6, R563, R565, R574, R577 R2, R5, R561, R562, R571 R10, R11, R12, R535, R536, R575 R3, R4 R7, R8, R9, R502, R510, R511 R500, R501, R576, R578, R579, R581 R503, R548, R549, R550 R504 R505 R506, R508, R509, R512, R554, R555, R556, R557, R560 Rev. 0 | Page 38 of 40 Supplier/Part Number PTMICRO10 Panasonic EVQ-PLDA15 SMA RF 5-pin upright Clock distribution Voltage regulator ADI AD9515BCPZ ADI ADP3339AKCZ-5 AD9254 Item 60 Qty. 1 61 62 Omit (DNP) Reference Designator U502 Device IC Package SOT-223 1 U503 IC SOT-223 2 U504, U505 IC SOT-223 U506 IC 8-pin SOIC SC70 SC70 48-pin TSSOP 48-pin LFCSP_VQ 16-pin LFCSP_VQ 63 1 64 65 66 1 1 1 U507 U508 U509 IC IC IC 67 1 U510 DUT (AD9254) IC 68 Total 1 128 U511 (or Z500) 107 Rev. 0 | Page 39 of 40 Description Voltage regulator Voltage regulator Voltage regulator 8-bit microcontroller Dual buffer Dual buffer Buffer/line driver ADC Supplier/Part Number ADI ADP3339AKCZ-1.8 Differential amplifier ADI AD8352ACPZ ADI ADP3339AKCZ-2.5 ADI ADP3339AKCZ-3.3 Microchip PIC12F629 Fairchild NC7WZ16 Fairchild NC7WZ07 Fairchild 74VCX162244 ADI AD9254BCPZ AD9254 OUTLINE DIMENSIONS 7.00 BSC SQ 0.60 MAX 37 36 PIN 1 INDICATOR TOP VIEW 12° MAX 48 PIN 1 INDICATOR 1 EXPOSED PAD 6.75 BSC SQ 4.25 4.10 SQ 3.95 (BOTTOM VIEW) 0.50 0.40 0.30 1.00 0.85 0.80 0.30 0.23 0.18 0.60 MAX 25 24 12 13 0.25 MIN 5.50 REF 0.80 MAX 0.65 TYP 0.05 MAX 0.02 NOM 0.50 BSC SEATING PLANE 0.20 REF COPLANARITY 0.08 COMPLIANT TO JEDEC STANDARDS MO-220-VKKD-2 Figure 64. 48-Lead Lead Frame Chip Scale Package [LFCSP_VQ] 7 mm × 7 mm Body, Very Thin Quad (CP-48-3) Dimensions shown in millimeters ORDERING GUIDE Model AD9254BCPZ-150 1, 2 AD9254BCPZRL7–1501, 2 AD9254-150EBZ1 1 2 Temperature Range –40°C to +85°C –40°C to +85°C Package Description 48-Lead Lead Frame Chip Scale Package (LFCSP_VQ) 48-Lead Lead Frame Chip Scale Package (LFCSP_VQ) Evaluation Board Z = Pb-free part. It is required that the exposed paddle be soldered to the AGND plane to achieve the best electrical and thermal performance. ©2006 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D06216-0-10/06(0) Rev. 0 | Page 40 of 40 Package Option CP-48-3 CP-48-3