PDF Data Sheet Rev. G

Data Sheet
2.7 V to 5.5 V, <100 μA, 8-/10-/12-Bit
nanoDAC, SPI Interface in LFCSP and SC70
AD5601/AD5611/AD5621
FEATURES
FUNCTIONAL BLOCK DIAGRAM
APPLICATIONS
GND
AD5601/AD5611/AD5621
POWER-ON
RESET
REF(+)
12-/10-/8-BIT
DAC
DAC
REGISTER
INPUT
CONTROL
LOGIC
OUTPUT
BUFFER
POWER-DOWN
CONTROL LOGIC
VOUT
RESISTOR
NETWORK
SYNC
SCLK SDIN
Figure 1.
Table 1. Related Devices
Part Number
AD5641
Description
2.7 V to 5.5 V, <100 μA, 14-bit nanoDAC in
SC70 and LFCSP packages
They also provide software-selectable output loads while in
power-down mode. The parts are put into power-down mode
over the serial interface.
Voltage level setting
Portable battery-powered instruments
Digital gain and offset adjustment
Programmable voltage and current sources
Programmable attenuators
GENERAL DESCRIPTION
The AD5601/AD5611/AD5621, members of the nanoDAC®
family, are single, 8-/10-/12-bit, buffered voltage output DACs
that operate from a single 2.7 V to 5.5 V supply, consuming
typically 75 μA at 5 V. The parts come in tiny LFCSP and SC70
packages. Their on-chip precision output amplifier allows railto-rail output swing to be achieved. The AD5601/AD5611/
AD5621 utilize a versatile 3-wire serial interface that operates at
clock rates up to 30 MHz and is compatible with SPI, QSPI™,
MICROWIRE™, and DSP interface standards.
The reference for the AD5601/AD5611/AD5621 is derived
from the power supply inputs and, therefore, gives the widest
dynamic output range. The parts incorporate a power-on reset
circuit, which ensures that the DAC output powers up to 0 V
and remains there until a valid write to the device takes place.
The AD5601/AD5611/AD5621 contain a power-down feature
that reduces current consumption to typically 0.2 μA at 3 V.
Rev. H
VDD
06853-001
6-lead SC70 and LFCSP packages
Micropower operation: 100 μA maximum at 5 V
Power-down typically to 0.2 μA at 3 V
2.7 V to 5.5 V power supply
Guaranteed monotonic by design
Power-on reset to 0 V with brownout detection
3 power-down functions
Low power serial interface with Schmitt-triggered inputs
On-chip output buffer amplifier, rail-to-rail operation
SYNC interrupt facility
Minimized zero-code error
AD5601 buffered 8-bit DAC
B version: ±0.5 LSB INL
AD5611 buffered 10-bit DAC
B version: ±0.5 LSB INL
A version: ±4 LSB INL
AD5621 buffered 12-bit DAC
B version: ±1 LSB INL
A version: ±6 LSB INL
The low power consumption of these parts in normal operation
makes them ideally suited to portable battery-operated equipment. The combination of small package and low power makes
these nanoDAC devices ideal for level-setting requirements,
such as generating bias or control voltages in space-constrained
and power-sensitive applications.
PRODUCT HIGHLIGHTS
1.
2.
3.
4.
5.
6.
Available in 6-lead LFCSP and SC70 packages.
Low power, single-supply operation. The AD5601/
AD5611/AD5621 operate from a single 2.7 V to 5.5 V
supply with a maximum current consumption of 100 μA,
making them ideal for battery-powered applications.
The on-chip output buffer amplifier allows the output of
the DAC to swing rail-to-rail with a typical slew rate of
0.5 V/μs.
Reference is derived from the power supply.
High speed serial interface with clock speeds up to
30 MHz. Designed for very low power consumption.
The interface powers up only during a write cycle.
Power-down capability. When powered down, the DAC
typically consumes 0.2 μA at 3 V. Power-on reset with
brownout detection.
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2005–2016 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
AD5601/AD5611/AD5621
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1 Output Amplifier........................................................................ 14 Applications ....................................................................................... 1 Serial Interface ............................................................................ 14 General Description ......................................................................... 1 Input Shift Register .................................................................... 14 Functional Block Diagram .............................................................. 1 SYNC Interrupt .......................................................................... 14 Product Highlights ........................................................................... 1 Power-On Reset .......................................................................... 16 Revision History ............................................................................... 2 Power-Down Modes .................................................................. 16 Specifications..................................................................................... 3 Microprocessor Interfacing ....................................................... 16 Timing Characteristics ................................................................ 4 Applications Information .............................................................. 18 Absolute Maximum Ratings............................................................ 5 ESD Caution .................................................................................. 5 Choosing a Reference as Power Supply for the
AD5601/AD5611/AD5621 ....................................................... 18 Pin Configurations and Function Descriptions ........................... 6 Bipolar Operation Using the AD5601/AD5611/AD5621 ..... 18 Typical Performance Characteristics ............................................. 7 Using the AD5601/AD5611/AD5621 with a Galvanically
Isolated Interface ........................................................................ 19 Terminology .................................................................................... 13 Theory of Operation ...................................................................... 14 DAC Section ................................................................................ 14 Resistor String ............................................................................. 14 Power Supply Bypassing and Grounding ................................ 19 Outline Dimensions ....................................................................... 20 Ordering Guide .......................................................................... 21 REVISION HISTORY
2/16—Rev. G to Rev. H
Changes to Noise Parameter, Table 2 ............................................. 3
Changes to Serial Interface Section .............................................. 14
6/13—Rev. F to Rev. G
Change to Ordering Guide ............................................................ 21
2/12—Rev. E to Rev. F
Added 6-Lead LFCSP ......................................................... Universal
Changes to Features Section, General Description Section,
Table 1, and Product Highlights Section ....................................... 1
Changes to Table 4 ............................................................................ 5
Added Figure 4; Renumbered Sequentially .................................. 6
Changes to Table 5 ............................................................................ 6
Changes to Choosing a Reference as Power Supply for the
AD5601/AD5611/AD5621 Section .............................................. 18
Updated Outline Dimensions ....................................................... 20
Changes to Ordering Guide .......................................................... 21
7/10—Rev. D to Rev. E
Changes to Figure 1 .......................................................................... 1
12/07—Rev. B to Rev. C
Changes to Features ..........................................................................1
Changes to Table 2.............................................................................3
Changes to AD5601/AD5611/AD5621 to ADSP-2101
Interface Section ............................................................................. 16
Updated Outline Dimensions ....................................................... 20
Changes to Ordering Guide .......................................................... 20
7/05—Rev. A to Rev. B
Changes to Figure 48...................................................................... 17
Changes to Galvanically Isolated Interface Section ................... 19
Changes to Figure 52...................................................................... 19
3/05—Rev. 0 to Rev. A
Changes to Timing Characteristics .................................................4
Changes to Absolute Maximum Ratings ........................................5
Changes to Full Scale Error Section ................................................7
Changes to Figure 20...................................................................... 10
Changes to Theory of Operation.................................................. 14
Changes to Power Down Modes .................................................. 15
1/05—Revision 0: Initial Version
5/08—Rev. C to Rev. D
Changes to General Description Section ...................................... 1
Changes to Table 2 ............................................................................ 3
Changes to Choosing a Reference as Power Supply for the
AD5601/AD5611/AD5621 Section .............................................. 18
Changes to Ordering Guide .......................................................... 20
Rev. H | Page 2 of 21
Data Sheet
AD5601/AD5611/AD5621
SPECIFICATIONS
VDD = 2.7 V to 5.5 V; RL = 2 kΩ to GND; CL = 200 pF to GND; all specifications TMIN to TMAX, unless otherwise noted. Temperature range
for A/B grades is −40°C to +125°C, typical at 25°C.
Table 2.
Parameter
STATIC PERFORMANCE
AD5601
Resolution
Relative Accuracy1 (INL)
Differential Nonlinearity (DNL)
AD5611
Resolution
Relative Accuracy1 (INL)
Differential Nonlinearity (DNL)
AD5621
Resolution
Relative Accuracy1 (INL)
Differential Nonlinearity (DNL)
Zero-Code Error
Full-Scale Error
Offset Error
Gain Error
Zero-Code Error Drift
Gain Temperature Coefficient
OUTPUT CHARACTERISTICS2
Output Voltage Range
Output Voltage Settling Time
Slew Rate
Capacitive Load Stability
Min
B Grade
Typ
Max
Unit
Test Conditions/Comments
±0.5
±0.5
Bits
LSB
LSB
Guaranteed monotonic by design
±4
±0.5
±0.5
±0.5
Bits
LSB
LSB
Guaranteed monotonic by design
±6
±0.5
10
±1
±0.5
10
10
12
0.5
±0.5
±0.063
±0.0004
5.0
2.0
0
6
0.5
470
1000
120
2
0.5
±0.5
±0.063
±0.0004
5.0
2.0
±10
±0.037
VDD
10
0
6
0.5
470
1000
120
2
5
0.2
15
0.5
±10
±0.037
±2
VDD
10
3
±2
0.8
0.6
3
Rev. H | Page 3 of 21
V
μs
V/μs
pF
pF
nV/Hz
μV p-p
nV-s
nV-s
mA
Ω
1.8
1.4
0.8
0.6
Bits
LSB
LSB
mV
mV
mV
%FSR
μV/°C
Guaranteed monotonic by design
All 0s loaded to DAC register
All 1s loaded to DAC register
ppm
FSR/°C
5
0.2
15
0.5
1.8
1.4
Input Low Voltage, VINL
Pin Input Capacitance
Min
8
Output Noise Spectral Density
Noise
Digital-to-Analog Glitch Impulse
Digital Feedthrough
Short-Circuit Current
DC Output Impedance
LOGIC INPUTS
Input Current3
Input High Voltage, VINH
A Grade
Typ
Max
μA
V
V
V
V
pF
Code ¼ scale to ¾ scale
RL = ∞
RL = 2 kΩ
DAC code = midscale,1 kHz
DAC code = midscale,
0.1 Hz to 10 Hz bandwidth
1 LSB change around major carry
VDD = 3 V/5 V
VDD = 4.7 V to 5.5 V
VDD = 2.7 V to 3.6 V
VDD = 4.7 V to 5.5 V
VDD = 2.7 V to 3.6 V
AD5601/AD5611/AD5621
Parameter
POWER REQUIREMENTS
VDD
IDD for Normal Mode
Min
2
3
A Grade
Typ
Max
2.7
VDD = ±4.5 V to ±5.5 V
VDD = ±2.7 V to ±3.6 V
IDD for All Power-Down Modes
VDD = ±4.5 V to ±5.5 V
VDD = ±2.7 V to ±3.6 V
POWER EFFICIENCY
IOUT/IDD
1
Data Sheet
5.5
Min
B Grade
Typ
Max
Test Conditions/Comments
5.5
V
100
90
μA
μA
0.5
0.2
0.5
0.2
μA
μA
All digital inputs at 0 V or VDD
DAC active and excluding load
current
VIH = VDD and VIL = GND
VIH = VDD and VIL = GND
VIH = VDD and VIL = GND
VIH = VDD and VIL = GND
VIH = VDD and VIL = GND
96
96
%
ILOAD = 2 mA and VDD = ±5 V
75
60
2.7
Unit
100
90
75
60
Linearity calculated using a reduced code range: AD5621 from Code 64 to Code 4032; AD5611 from Code 16 to Code 1008; AD5601 from Code 4 to Code 252.
Guaranteed by design and characterization, not production tested.
Total current flowing into all pins.
TIMING CHARACTERISTICS
VDD = 2.7 V to 5.5 V; all specifications TMIN to TMAX, unless otherwise noted. See Figure 2.
Table 3.
Limit1
33
5
5
10
5
4.5
0
20
13
Parameter
t12
t2
t3
t4
t5
t6
t7
t8
t9
2
Test Conditions/Comments
SCLK cycle time
SCLK high time
SCLK low time
SYNC to SCLK falling edge setup time
Data setup time
Data hold time
SCLK falling edge to SYNC rising edge
Minimum SYNC high time
SYNC rising edge to next SCLK falling edge ignored
All input signals are specified with tr = tf = 1 ns/V (10% to 90% of VDD) and timed from a voltage level of (VIL + VIH)/2.
Maximum SCLK frequency is 30 MHz.
t4
SCLK
t2
t8
t1
t9
t3
t7
SYNC
t6
t5
SDIN
D15
D14
D2
D1
Figure 2. Timing Diagram
Rev. H | Page 4 of 21
D0
D15
D14
06853-002
1
Unit
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
Data Sheet
AD5601/AD5611/AD5621
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 4.
Parameter
VDD to GND
Digital Input Voltage to GND
VOUT to GND
Operating Temperature Range
Industrial (A/B Grades)
Storage Temperature Range
Maximum Junction Temperature
SC70 Package
θJA Thermal Impedance
θJC Thermal Impedance
LFCSP Package
θJA Thermal Impedance
Lead Temperature, Soldering
Vapor Phase (60 sec)
Infrared (15 sec)
ESD (Human Body Model)
Rating
−0.3 V to +7.0 V
−0.3 V to VDD + 0.3 V
−0.3 V to VDD + 0.3 V
−40°C to +125°C
−65°C to +160°C
150°C
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
ESD CAUTION
433.34°C/W
149.47°C/W
95°C/W
215°C
220°C
2.0 kV
Rev. H | Page 5 of 21
AD5601/AD5611/AD5621
Data Sheet
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
SDIN 3
TOP VIEW
(Not to Scale)
6
VDD 1
VOUT
SCLK 2
5
GND
4
VDD
SDIN 3
AD5601/
AD5611/
AD5621
TOP VIEW
(Not to Scale)
6 VOUT
5 GND
4 SYNC
NOTES:
1. CONNECT THE EXPOSED PAD TO GND.
Figure 3. 6-Lead SC70 Pin Configuration
06853-053
SCLK 2
AD5601/
AD5611/
AD5621
06853-003
SYNC 1
Figure 4. 6-Lead LFCSP Pin Configuration
Table 5. Pin Function Descriptions
SC70
Pin No.
1
LFCSP
Pin No.
4
Mnemonic
SYNC
2
2
SCLK
3
3
SDIN
4
1
VDD
5
6
5
6
GND
VOUT
EP
Description
Level-Triggered Control Input (Active Low). This is the frame synchronization signal for the input
data. When SYNC goes low, it enables the input shift register, and data is transferred in on the falling
edges of the clocks that follow. The DAC is updated following the 16th clock cycle, unless SYNC is
taken high before this edge, in which case the rising edge of SYNC acts as an interrupt and the write
sequence is ignored by the DAC.
Serial Clock Input. Data is clocked into the input shift register on the falling edge of the serial clock
input. Data can be transferred at rates up to 30 MHz.
Serial Data Input. This device has a 16-bit shift register. Data is clocked into the register on the falling
edge of the serial clock input.
Power Supply Input. The AD5601/AD5611/AD5621 can be operated from 2.7 V to 5.5 V. VDD should be
decoupled to GND.
Ground. Ground reference point for all circuitry on the AD5601/AD5611/AD5621.
Analog Output Voltage from the DAC. The output amplifier has rail-to-rail operation.
Exposed Pad. Connect to GND.
Rev. H | Page 6 of 21
Data Sheet
AD5601/AD5611/AD5621
TYPICAL PERFORMANCE CHARACTERISTICS
2.5
VDD = VREF = 5V
TA = 25°C
0.5
INL ERROR (LSB)
VDD = VREF = 5V
TA = 25°C
2.0
TOTAL UNADJUSTED ERROR (LSB)
1.0
0
–0.5
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
1064
1564
2064
2564
3064
3564
DAC CODE
4064
–2.5
64
564
Figure 5. Typical AD5621 INL
0.5
0.6
TOTAL UNADJUSTED ERROR (LSB)
0.3
0.2
INL ERROR (LSB)
1564
2064
2564
DAC CODE
3064
3564
4064
Figure 8. AD5621 Total Unadjusted Error (TUE)
VDD = VREF = 5V
TA = 25°C
0.4
1064
06853-007
564
06853-004
–2.0
–1.0
64
0.1
0
–0.1
–0.2
–0.3
VDD = VREF = 5V
TA = 25°C
0.4
0.2
0
–0.2
–0.4
216
316
416 516 616
DAC CODE
716
816
916
–0.6
16
Figure 6. Typical AD5611 INL
0.100
0.20
TOTAL UNADJUSTED ERROR (LSB)
0.025
0
–0.025
–0.050
–0.075
4
54
104
154
DAC CODE
204
06853-006
INL ERROR (LSB)
0.050
–0.100
216
316
416 516 616
DAC CODE
716
816
916
Figure 9. AD5611 Total Unadjusted Error (TUE)
VDD = VREF = 5V
TA = 25°C
0.075
116
Figure 7. Typical AD5601 INL
VDD = VREF = 5V
TA = 25°C
0.15
0.10
0.05
0
–0.05
–0.10
–0.15
–0.20
4
54
104
154
DAC CODE
204
Figure 10. AD5601 Total Unadjusted Error (TUE)
Rev. H | Page 7 of 21
06853-009
116
06853-005
–0.5
16
06853-008
–0.4
AD5601/AD5611/AD5621
0.20
Data Sheet
12
V DD = 5V
T A = 25°C
0.15
10
VDD = 3V
VIH = DVDD
VIL = GND
TA = 25°C
VDD = 5V
VIH = DVDD
VIL = GND
TA = 25°C
NUMBER OF DEVICES
DNL ERROR (LSB)
0.10
0.05
0 0
–0.05
8
6
4
–0.10
0
IDD (mA)
Figure 11. Typical AD5621 DNL
0.05
0.04
Figure 14. IDD Histogram (3 V/5 V)
TA = 25°C
VDD = 5V
VDD = 5V
TA = 25°C
CH1 = SCLK
DNL ERROR (LSB)
0.03
0.02
0.01
0
–0.01
–0.02
–0.03
CH2 = VOUT
116
216
316
416 516 616
DAC CODE
716
816
916
CH1 = 5V/DIV CH2 = 1V/DIV TIME BASE = 2µs/DIV
Figure 12. Typical AD5611 DNL
Figure 15. Full-Scale Settling Time
0.010
VDD = 5V
TA = 25°C
0.008
06853-014
–0.05
16
06853-011
–0.04
CH1 = SCLK
TA = 25°C
VDD = 5V
0.006
0.002
0
CH2 = VOUT
–0.002
–0.004
06853-015
–0.006
–0.008
–0.010
4
54
104
154
DAC CODE
204
06853-012
DNL ERROR (LSB)
0.004
Figure 13. Typical AD5601 DNL
CH1 = 5V/DIV CH2 = 1V/DIV TIME BASE = 2µs/DIV
Figure 16. Half-Scale Settling Time
Rev. H | Page 8 of 21
06853-013
3564
0.05885
0.06648
0.06710
0.06773
0.06835
0.06897
0.06960
0.07022
0.07084
0.07147
0.07209
0.07271
0.07334
3064
0.05814
1564
2064
2564
DAC CODE
0.05742
1064
0.05671
564
0.05599
64
06853-010
–0.20
0.05456
0.05527
2
–0.15
Data Sheet
AD5601/AD5611/AD5621
VDD = 5V
TA = 25°C
MIDSCALE LOADED
VDD
VDD = 5V
TA = 25°C
CH1
CH1
06853-016
06853-019
VOUT = 70mV
CH2
CH1 1V, CH2 20mV, TIME BASE = 20µs/DIV
CH1 5µV/DIV
Figure 17. Power-On Reset to 0 V
Figure 20. 1/f Noise, 0.1 Hz to 10 Hz Bandwidth
CH1
VDD
VDD = 5V
TA = 25°C
VDD = 5V
TA = 25°C
CH1
VOUT
CH2
CH2
CH1 1V, CH2 5V, TIME BASE = 50µs/DIV
CH1 5V, CH2 1V, TIME BASE = 2µs/DIV
Figure 18. VDD vs. VOUT
Figure 21. Exiting Power-Down Mode
140
2.458
3/4 SCALE
2.456
2.452
MIDSCALE
100
1/4 SCALE
2.450
80
IDD (µA)
2.448
2.446
2.444
2.438
0
100
200
300
SAMPLE NUMBER
400
500
ZERO SCALE
40
TA = 25°C
VDD = 5V
LOAD = 2kΩ AND 220pF
CODE 0x2000 TO 0x1FFF
10ns/SAMPLE NUMBER
2.440
60
20
0
0
5
10
15
FREQUENCY (MHz)
Figure 22. IDD vs. SCLK vs. Code
Figure 19. Digital-to-Analog Glitch Energy
Rev. H | Page 9 of 21
20
25
06853-021
2.442
06853-018
AMPLITUDE (V)
FULL SCALE
120
2.454
2.436
06853-020
06853-017
VOUT
AD5601/AD5611/AD5621
0.3
VDD = 5V
TA = 25°C
UNLOADED OUTPUT
600
VDD = 5V
0.1
AD5601 MAX INL ERROR
AD5611 MAX INL ERROR
500
300
MIDSCALE
–0.1 AD5611 MIN INL ERROR
AD5601 MIN INL ERROR
–0.2
–0.3
FULL SCALE
–0.4
AD5621 MIN INL ERROR
–0.5
ZERO SCALE
1k
10k
FREQUENCY (Hz)
100k
–0.6
–40
–20
0.08
0.07
0.06
TA = 25°C
60
50
DNL ERROR (LSB)
30
20
4000
6000 8000 10000 12000 14000 16000
DIGITAL INPUT CODE
06853-023
10
2000
100
120
AD5621 MAX DNL ERROR
0.05
0.04
0.03
AD5611 MAX DNL ERROR
0.02
0.01
0
–0.01
–0.02
AD5601 MAX DNL ERROR
AD5611 MIN DNL ERROR
AD5601 MIN DNL ERROR
–0.03
–0.04
–0.05
–0.06
AD5621 MIN DNL ERROR
–0.07
–0.08
–40
10
60
110
160
TEMPERATURE (°C)
Figure 27. DNL vs. Temperature (5 V)
0.8
0.00149
VDD = 5V
TA = 25°C
DAC LOADED WITH ZERO-SCALE CODE
VDD = 5V
AD5621 ZERO-CODE ERROR
0.00099
ERROR (LSB)
0.4
0.2
0.0
–0.2
AD5611 ZERO-CODE ERROR
AD5601 ZERO-CODE ERROR
AD5601 FULL-SCALE ERROR
0.00049
–0.00001
–15
–10
–5
0
5
10
15
06853-024
DAC LOADED WITH FULL-SCALE CODE
–0.4
–0.6
80
VDD = 5V
Figure 24. Supply Current vs. Digital Input Code
0.6
60
I (mA)
AD5611 FULL-SCALE ERROR
AD5621 FULL-SCALE ERROR
–0.00051
–40
–20
0
–20
40
60
80
TEMPERATURE (°C)
100
120
140
Figure 28. Zero-Code Error and Full-Scale Error vs. Temperature
Figure 25. Sink and Source Capability
Rev. H | Page 10 of 21
06853-027
IDD (µA)
VDD = 3V
40
0
40
Figure 26. INL vs. Temperature (5 V)
70
0
20
TEMPERATURE (°C)
Figure 23. Noise Spectral Density
VDD = 5V
0
06853-025
100
06853-026
200
0
INL ERROR (LSB)
400
0
100
∆VOUT (V)
AD5621 MAX INL ERROR
0.2
06853-022
OUTPUT NOISE SPECTRAL DENSITY (nV/ Hz)
700
Data Sheet
Data Sheet
AD5601/AD5611/AD5621
0.10
1.5
0.09
AD5621 MAX TUE
1.1
0.08
0.9
0.07
VDD = 5V
0.06
IDD (mA)
0.7
0.5
AD5601 MAX TUE
AD5611 MAX TUE
0.3
0.05
VDD = 3V
0.04
0.03
0.1
0.02
–0.1
AD5601 MIN TUE
AD5611 MIN TUE
AD5621 MIN TUE
–0.5
–40
–20
0
20
40
60
80
TEMPERATURE (°C)
0.01
100
120
140
0
–40
–20
0
20
40
60
80
100
120
140
TEMPERATURE (°C)
Figure 29. Total Unadjusted Error (TUE) vs. Temperature (5 V)
06853-031
–0.3
06853-028
TOTAL UNADJUSTED ERROR (LSB)
1.3
Figure 32. Supply Current vs. Temperature (3 V/5 V Supply)
1.5
1.4
0.4
TA = 25°C
1.3
1.2
0.2
VDD = 5V
1.0
INL ERROR (LSB)
OFFSET ERROR (mV)
1.1
0.9
0.8
0.7
VDD = 3V
0.6
0.5
AD5621 MAX INL ERROR
AD5601 MAX INL ERROR
AD5611 MAX INL ERROR
0
AD5601 MIN INL ERROR
–0.2
AD5611 MIN INL ERROR
0.4
0.3
–0.4
AD5621 MIN INL ERROR
0.2
0
20
40
60
80
TEMPERATURE (°C)
100
120
140
–0.6
2.7
–0.002
VDD = 5V
DNL ERROR (LSB)
–0.006
–0.008
–0.010
VDD = 3V
–0.012
–0.014
20
40
60
80
TEMPERATURE (°C)
100
120
140
06853-030
GAIN ERROR (%FSR)
–0.004
0
4.2
4.7
5.2
Figure 33. INL vs. Supply Voltage at 25°C
0
–20
3.7
SUPPLY VOLTAGE (V)
Figure 30. Offset Error vs. Temperature (3 V/5 V Supply)
–0.016
–40
3.2
Figure 31. Gain Error vs. Temperature (3 V/5 V Supply)
0.10
0.09
0.08
0.07
0.06
0.05
0.04
0.03
0.02
0.01
0
–0.01
–0.02
–0.03
–0.04
–0.05
–0.06
–0.07
–0.08
–0.09
–0.10
2.7
TA = 25°C
AD5621 MAX DNL ERROR
AD5611 MAX DNL ERROR
AD5611 MIN DNL ERROR
AD5601 MAX DNL ERROR
AD5601 MIN DNL ERROR
AD5621 MIN DNL ERROR
3.2
3.7
4.2
4.7
5.2
SUPPLY VOLTAGE (V)
5.7
Figure 34. DNL vs. Supply Voltage at 25°C
Rev. H | Page 11 of 21
6.2
6.7
06853-033
–20
06853-029
0
–40
06853-032
0.1
AD5601/AD5611/AD5621
1.5
0.10
TA = 25°C
1.3
TA = 25°C
0.09
AD5621 MAX TUE
0.08
1.1
0.07
0.9
IDD (mA)
0.7
0.5
0.3
0.06
0.05
AD5611 MAX TUE
0.04
AD5621 MIN TUE
0.03
0.1
0.02
AD5601 MAX TUE
AD5611 MIN TUE
AD5601 MIN TUE
–0.3
2.7
3.2
0.01
3.7
4.2
4.7
SUPPLY VOLTAGE (V)
5.2
0
2.7
4.2
4.7
AD5621 ZERO-CODE ERROR
TA = 25°C
400
0.0008
SCLK/SDIN
INCREASING
VDD = 5V
SCLK/SDIN
DECREASING
VDD = 5V
350
0.0006
300
0.0004
AD5601 FULL-SCALE ERROR
IDD (µA)
ERROR (LSB)
5.2
Figure 37. Supply Current vs. Supply Voltage at 25°C
450
TA = 25°C
3.7
SUPPLY VOLTAGE (V)
Figure 35. Total Unadjusted Error (TUE) vs. Supply Voltage at 25°C
0.0010
3.2
06853-036
–0.1
06853-034
TOTAL UNADJUSTED ERROR (LSB)
Data Sheet
AD5611 ZERO-CODE ERROR
0.0002
SCLK/SDIN
INCREASING
VDD = 3V
250
200
AD5601 ZERO-CODE ERROR
150
AD5611 FULL-SCALE ERROR
100
AD5621 FULL-SCALE ERROR
50
–0.0004
2.7
3.2
3.7
4.2
4.7
5.2
SUPPLY VOLTAGE (V)
5.7
6.2
6.7
Figure 36. Zero-Code Error and Full-Scale Error vs. Supply Voltage at 25°C
Rev. H | Page 12 of 21
0
SCLK/SDIN DECREASING VDD = 3V
0
1
2
3
4
VLOGIC (V)
Figure 38. SCLK/SDIN vs. Logic Voltage
5
6
06853-037
–0.0002
06853-035
0
Data Sheet
AD5601/AD5611/AD5621
TERMINOLOGY
Relative Accuracy
For the DAC, relative accuracy or integral nonlinearity (INL) is
a measure of the maximum deviation, in LSBs, from a straight
line passing through the endpoints of the DAC transfer function. See Figure 5 to Figure 7 for plots of typical INL vs. code.
Differential Nonlinearity
Differential nonlinearity (DNL) is the difference between the
measured change and the ideal 1 LSB change between any two
adjacent codes. A specified differential nonlinearity of ±1 LSB
maximum ensures monotonicity. This DAC is guaranteed
monotonic by design. See Figure 11 to Figure 13 for plots of
typical DNL vs. code.
Zero-Code Error
Zero-code error is a measure of the output error when zero
code (0x0000) is loaded to the DAC register. Ideally, the output
should be 0 V. The zero-code error is always positive in the
AD5601/AD5611/AD5621 because the output of the DAC cannot
go below 0 V. Zero-code error is due to a combination of the
offset errors in the DAC and output amplifier. Zero-code error
is expressed in mV. See Figure 28 for a plot of zero-code error
vs. temperature.
Full-Scale Error
Full-scale error is a measure of the output error when full-scale
code (0xFFFF) is loaded to the DAC register. Ideally, the output
should be VDD − 1 LSB. Full-scale error is expressed in mV. See
Figure 28 for a plot of full-scale error vs. temperature.
Total Unadjusted Error
Total unadjusted error (TUE) is a measure of the output error,
taking all the various errors into account. See Figure 8 to
Figure 10 for plots of typical TUE vs. code.
Zero-Code Error Drift
Zero-code error drift is a measure of the change in zero-code
error with a change in temperature. It is expressed in μV/°C.
Gain Temperature Coefficient
Gain temperature coefficient is a measure of the change in gain
error with changes in temperature. It is expressed in (ppm of
full-scale range)/°C.
Digital-to-Analog Glitch Impulse
Digital-to-analog glitch impulse is the impulse injected into the
analog output when the input code in the DAC register changes
state. It is normally specified as the area of the glitch in nV-s
and is measured when the digital input code is changed by
1 LSB at the major carry transition (0x2000 to 0x1FFF). See
Figure 19.
Digital Feedthrough
Digital feedthrough is a measure of the impulse injected into
the analog output of the DAC from the digital inputs of the
DAC, but is measured when the DAC output is not updated.
It is specified in nV-s and is measured with a full-scale code
change on the data bus—from all 0s to all 1s and vice versa.
Gain Error
Gain error is a measure of the span error of the DAC. It is the
deviation in slope of the DAC transfer characteristic from the
ideal, expressed as a percent of the full-scale range.
Rev. H | Page 13 of 21
AD5601/AD5611/AD5621
Data Sheet
THEORY OF OPERATION
DAC SECTION
OUTPUT AMPLIFIER
The AD5601/AD5611/AD5621 DACs are fabricated on a
CMOS process. The architecture consists of a string DAC
followed by an output buffer amplifier. Figure 39 is a block
diagram of the DAC architecture.
The output buffer amplifier is capable of generating rail-to-rail
voltages on its output, giving an output range of 0 V to VDD. It is
capable of driving a load of 2 kΩ in parallel with 1000 pF to
GND. The source and sink capabilities of the output amplifier
are shown in Figure 25. The slew rate is 0.5 V/μs, with a halfscale settling time of 8 μs with the output loaded.
VDD
REF (+)
RESISTOR
NETWORK
DAC REGISTER
REF (–)
VOUT
06853-038
OUTPUT
AMPLIFIER
GND
Figure 39. DAC Architecture
Because the input coding to the DAC is straight binary, the ideal
output voltage is given by
D
VOUT  VDD   n 
2 
where:
D is the decimal equivalent of the binary code that is loaded to
the DAC register.
n is the bit resolution of the DAC.
RESISTOR STRING
The resistor string structure is shown in Figure 40. It is simply a
string of resistors, each of Value R. The code loaded to the DAC
register determines at which node on the string the voltage is
tapped off to be fed into the output amplifier. The voltage is
tapped off by closing one of the switches connecting the string
to the amplifier. Because it is a string of resistors, it is guaranteed monotonic.
R
R
TO OUTPUT
AMPLIFIER
R
SERIAL INTERFACE
The AD5601/AD5611/AD5621 have a 3-wire serial interface
(SYNC, SCLK, and SDIN) that is compatible with SPI, QSPI,
and MICROWIRE interface standards as well as most DSPs. See
Figure 2 for a timing diagram of a typical write sequence.
The write sequence begins by bringing the SYNC line low. Data
from the SDIN line is clocked into the 16-bit shift register on
the falling edge of SCLK. The serial clock frequency can be as
high as 30 MHz, making the AD5601/AD5611/AD5621 compatible with high speed DSPs. On the 16th falling clock edge,
the last data bit is clocked in and the programmed function is
executed (a change in DAC register contents and/or a change
in the mode of operation). At this stage, the SYNC line may be
kept low or brought high. In either case, it must be brought high
for a minimum of 20 ns before the next write sequence so that a
falling edge of SYNC can initiate the next write sequence.
Because the SYNC buffer draws more current when VIN = 1.8 V
than it does when VIN = 0.8 V, SYNC should be idled low
between write sequences for even lower power operation of the
part, as mentioned previously. However, it must be brought
high again just before the next write sequence.
INPUT SHIFT REGISTER
The input shift register is 16 bits wide (see Figure 41). The first
two bits are control bits, which control the operating mode of
the part (normal mode or any one of three power-down
modes). For a complete description of the various modes, see
the Power-Down Modes section. For the AD5621, the next
12 bits are the data bits, which are transferred to the DAC
register on the 16th falling edge of SCLK. The information in
the last two bits is ignored by the AD5621. See Figure 42 and
Figure 43 for the AD5611 and AD5601 input shift register map.
SYNC INTERRUPT
R
06853-039
R
In a normal write sequence, the SYNC line is kept low for at
least 16 falling edges of SCLK and the DAC is updated on the
16th falling edge. However, if SYNC is brought high before the
16th falling edge, this acts as an interrupt to the write sequence.
The shift register is reset and the write sequence is seen as
invalid. Neither an update of the DAC register contents nor a
change in the operating mode occurs (see Figure 44).
Figure 40. Resistor String Structure
Rev. H | Page 14 of 21
Data Sheet
AD5601/AD5611/AD5621
DB15 (MSB)
PD1
DB0 (LSB)
PD0
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
X
X
DATA BITS
0
0
NORMAL OPERATION
0
1
1kΩ TO GND
1
0
100kΩ TO GND
1
1
THREE-STATE
06853-040
POWER-DOWN MODES
Figure 41. AD5621 Input Register Contents
DB15 (MSB)
PD1
DB0 (LSB)
PD0
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
X
X
X
X
X
X
X
X
X
DATA BITS
0
0
NORMAL OPERATION
0
1
1kΩ TO GND
1
0
100kΩ TO GND
1
1
THREE-STATE
06853-041
POWER-DOWN MODES
Figure 42. AD5611 Input Register Contents
DB15 (MSB)
PD1
DB0 (LSB)
PD0
D8
D7
D6
D5
D4
D3
D2
D1
X
DATA BITS
0
0
NORMAL OPERATION
0
1
1kΩ TO GND
1
0
100kΩ TO GND
1
1
THREE-STATE
06853-042
POWER-DOWN MODES
Figure 43. AD5601 Input Register Contents
SCLK
SDIN
DB15
DB0
DB15
DB0
VALID WRITE SEQUENCE, OUTPUT UPDATES
ON THE 16TH FALLING EDGE
INVALID WRITE SEQUENCE:
SYNC HIGH BEFORE 16TH FALLING EDGE
Figure 44. SYNC Interrupt Facility
Rev. H | Page 15 of 21
06853-043
SYNC
AD5601/AD5611/AD5621
Data Sheet
POWER-ON RESET
MICROPROCESSOR INTERFACING
The AD5601/AD5611/AD5621 contain a power-on reset circuit
that controls the output voltage during power-up. The DAC
register is filled with 0s and the output voltage is 0 V. It remains
there until a valid write sequence is made to the DAC. This is
useful in applications in which it is important to know the state
of the DAC output while it is in the process of powering up.
AD5601/AD5611/AD5621 to ADSP-2101 Interface
The AD5601/AD5611/AD5621 have four separate modes of
operation. These modes are software-programmable by setting
two bits (DB15 and DB14) in the control register. Table 6 shows
how the state of the bits corresponds to the operating mode of
the device.
ADSP-2101*
Table 6. Operating Modes of the AD5601/AD5611/AD5621
0
1
1
DB14
0
1
0
1
Operating Mode
Normal operation
Power-down modes:
1 kΩ to GND
100 kΩ to GND
Three-state
SDIN
Figure 46. AD5601/AD5611/AD5621 to ADSP-2101 Interface
AD5601/AD5611/AD5621 to 68HC11/68L11 Interface
There are three different options: the output is connected
internally to GND through a 1 kΩ resistor or a 100 kΩ resistor,
or the output is left open-circuited (three-stated). Figure 45
shows the output stage.
Figure 47 shows a serial interface between the AD5601/
AD5611/AD5621 and the 68HC11/68L11 microcontroller. SCK
of the 68HC11/68L11 drives the SCLK of the AD5601/AD5611/
AD5621, while the MOSI output drives the serial data line of
the DAC. The SYNC signal is derived from a port line (PC7).
The setup conditions for correct operation of this interface are
as follows: the 68HC11/68L11 should be configured so that the
CPOL bit is 0 and the CPHA bit is 1. When data is being transmitted to the DAC, the SYNC line is taken low (PC7). When the
68HC11/68L11 are configured as indicated, data appearing on
the MOSI output is valid on the falling edge of SCK. Serial data
from the 68HC11/68L11 is transmitted in 8-bit bytes with only
eight falling clock edges occurring in the transmit cycle. Data is
transmitted MSB first. To load data to the AD5601/AD5611/
AD5621, PC7 is left low after the first eight bits are transferred
and a second serial write operation is performed to the DAC.
PC7 is taken high at the end of this procedure.
VOUT
RESISTOR
NETWORK
06853-044
68HC11/
68L11*
POWER-DOWN
CIRCUITRY
SCLK
*ADDITIONAL PINS OMITTED FOR CLARITY
Not only does the supply current fall, but the output stage is
also internally switched from the output of the amplifier to a
resistor network of known values. This has the advantage that
the output impedance of the part is known while the part is in
power-down mode.
AMPLIFIER
SYNC
DT
SCLK
When both bits are set to 0, the part has normal power
consumption of 100 μA maximum at 5 V. However, for the
three power-down modes, the supply current falls to typically
0.2 μA at 3 V.
RESISTOR
STRING DAC
TFS
Figure 45. Output Stage During Power-Down
AD5601/AD5611/
AD5621*
PC7
SYNC
SCK
SCLK
MOSI
SDIN
*ADDITIONAL PINS OMITTED FOR CLARITY
The bias generator, output amplifier, resistor string, and other
associated linear circuitry are all shut down when power-down
mode is activated. However, the contents of the DAC register
are unaffected when in power-down. The time to exit powerdown is typically 13 μs for VDD = 5 V and 16 μs for VDD = 3 V.
See Figure 21 for a plot.
Rev. H | Page 16 of 21
Figure 47. AD5601/AD5611/AD5621 to 68HC11/68L11 Interface
06853-046
DB15
0
AD5601/AD5611/
AD5621*
06853-045
POWER-DOWN MODES
Figure 46 shows a serial interface between the AD5601/
AD5611/AD5621 and the ADSP-2101. The ADSP-2101 should
be set up to operate in SPORT transmit alternate framing mode.
The ADSP-2101 SPORT is programmed through the SPORT
control register and should be configured as follows: internal
clock operation, active low framing, and 16-bit word length.
Transmission is initiated by writing a word to the Tx register
after the SPORT is enabled.
Data Sheet
AD5601/AD5611/AD5621
Figure 48 shows a serial interface between the AD5601/AD5611/
AD5621 and the Blackfin ADSP-BF53x microprocessor. The
ADSP-BF53x processor family incorporates two dual-channel
synchronous serial ports, SPORT1 and SPORT0, for serial and
multiprocessor communications. Using SPORT0 to connect to
the AD5601/AD5611/AD5621, the setup for the interface is as
follows: DT0PRI drives the SDIN pin of the AD5601/AD5611/
AD5621, while TSCLK0 drives the SCLK of the part. The SYNC
is driven from TFS0.
AD5601/AD5611/
AD5621*
SDIN
SCLK
TFS0
SYNC
AD5601/AD5611/
AD5621*
P3.3
SYNC
TxD
SCLK
RxD
SDIN
Figure 49. AD5601/AD5611/AD5621 to 80C51/80L51 Interface
AD5601/AD5611/AD5621 to MICROWIRE Interface
*ADDITIONAL PINS OMITTED FOR CLARITY
Figure 48. AD5601/AD5611/AD5621 to Blackfin ADSP-BF53x Interface
AD5601/AD5611/AD5621 to 80C51/80L51 Interface
Figure 49 shows a serial interface between the AD5601/
AD5611/AD5621 and the 80C51/80L51 microcontroller. The
setup for the interface is as follows: TxD of the 80C51/80L51
drives SCLK of the AD5601/AD5611/AD5621, while RxD
drives the serial data line of the part. The SYNC signal is again
derived from a bit programmable pin on the port. In this case,
Port Line P3.3 is used. When data is to be transmitted to the
AD5601/AD5611/AD5621, P3.3 is taken low. The 80C51/80L51
transmit data only in 8-bit bytes; therefore, only eight falling
clock edges occur in the transmit cycle. To load data to the
DAC, P3.3 is left low after the first eight bits are transmitted,
Figure 50 shows an interface between the AD5601/AD5611/
AD5621 and any MICROWIRE-compatible device. Serial data
is shifted out on the falling edge of the serial clock and is
clocked into the AD5601/AD5611/AD5621 on the rising edge
of the SK.
MICROWIRE*
AD5601/AD5611/
AD5621*
CS
SYNC
SK
SCLK
SO
SDIN
*ADDITIONAL PINS OMITTED FOR CLARITY
Rev. H | Page 17 of 21
Figure 50. AD5601/AD5611/AD5621 to MICROWIRE Interface
06853-049
DT0PRI
TSCLK0
80C51/80L51*
*ADDITIONAL PINS OMITTED FOR CLARITY
06853-047
ADSP-BF53x*
and a second write cycle is initiated to transmit the second byte
of data. P3.3 is taken high following the completion of this
cycle. The 80C51/80L51 output the serial data LSB first. The
AD5601/AD5611/AD5621 require data with the MSB as the
first bit received. The 80C51/80L51 transmit routine should
take this into account.
06853-048
AD5601/AD5611/AD5621 to Blackfin® ADSP-BF53x
Interface
AD5601/AD5611/AD5621
Data Sheet
APPLICATIONS INFORMATION
CHOOSING A REFERENCE AS POWER SUPPLY FOR
THE AD5601/AD5611/AD5621
BIPOLAR OPERATION USING THE
AD5601/AD5611/AD5621
The AD5601/AD5611/AD5621 come in tiny LFCSP and SC70
packages with less than a 100 μA supply current. Because of this,
the choice of reference depends on the application requirements.
For applications with space-saving requirements, the ADR02
is recommended. It is available in an SC70 package and has
excellent drift at 9 ppm/°C (3 ppm/°C in the R-8 package) and
provides very good noise performance at 3.4 μV p-p in the
0.1 Hz to 10 Hz range.
The AD5601/AD5611/AD5621 have been designed for singlesupply operation, but a bipolar output range is also possible
using the circuit shown in Figure 52. The circuit in Figure 52
gives an output voltage range of ±5 V. Rail-to-rail operation at
the amplifier output is achievable using an AD820 or OP295 as
the output amplifier.
+5V
+5V
AD820/
OP295
10µF
0.1µF
+5V
VOUT
VDD
AD5601/AD5611/
AD5621
–5V
3-WIRE
SERIAL
INTERFACE
7V
ADR395
R1 = 10kΩ
5V
Figure 52. Bipolar Operation with the AD5601/AD5611/AD5621
The output voltage for any input code can be calculated as
SYNC
SCLK
SDIN
AD5601/AD5611/
AD5621
D
R1  R2 

 R2 
VOUT  VDD   N   

  VDD  
2
R1


 R1 



VOUT = 0V TO 5V
06853-050
3-WIRE
SERIAL
INTERFACE
Figure 51. ADR395 as Power Supply to the AD5601/AD5611/AD5621
where D represents the input code in decimal (0 – 2N).
With VDD = 5 V, R1 = R2 = 10 kΩ
 10  D 
VOUT   N   5 V

 2
Some recommended precision references for use as supplies to
the AD5601/AD5611/AD5621 are listed in Table 7.
Table 7. Precision References for the AD5601/AD5611/AD5621
Part No.
ADR435
ADR425
ADR02
ADR02
ADR395
Initial
Accuracy
(mV max)
±2
±2
±3
±3
±5
Temp Drift
(ppm/°C max)
3 (R-8)
3 (R-8)
3 (R-8)
3 (SC70)
9 (TSOT-23)
0.1 Hz to 10 Hz
Noise (μV p-p typ)
8
3.4
10
10
8
This is an output voltage range of ±5 V, with 0x0000 corresponding to a −5 V output and 0x3FFF corresponding to a
+5 V output.
Rev. H | Page 18 of 21
06853-051
Because the supply current required by the AD5601/AD5611/
AD5621 is extremely low, the parts are ideal for low supply
applications. The ADR395 voltage reference is recommended in
this case. It requires less than 100 μA of quiescent current and
can, therefore, drive multiple DACs in one system, if required.
It also provides very good noise performance at 8 μV p-p in the
0.1 Hz to 10 Hz range.
R2 = 10kΩ
Data Sheet
AD5601/AD5611/AD5621
USING THE AD5601/AD5611/AD5621 WITH A
GALVANICALLY ISOLATED INTERFACE
POWER SUPPLY BYPASSING AND GROUNDING
In process control applications in industrial environments,
it is often necessary to use a galvanically isolated interface to
protect and isolate the controlling circuitry from any hazardous
common-mode voltages that might occur in the area where the
DAC is functioning. iCoupler® provides isolation in excess of
2.5 kV. Because the AD5601/AD5611/AD5621 use a 3-wire serial
logic interface, the ADuM1300 3-channel digital isolator
provides the required isolation (see Figure 53). The power
supply to the part also needs to be isolated, which is done by
using a transformer. On the DAC side of the transformer, a 5 V
regulator provides the 5 V supply required for the AD5601/
AD5611/AD5621.
5V
REGULATOR
POWER
10µF
0.1µF
VDD
VIA
VOA
SCLK
ADuM1300
SDI
VIB
VOB
SYNC
DATA
VIC
VOC
SDIN
AD5601/
AD5611/
AD5621
GND
VOUT
06853-052
SCLK
Figure 53. AD5601/AD5611/AD5621 with a Galvanically Isolated Interface
When accuracy is important in a circuit, it is helpful to carefully
consider the power supply and ground return layout on the
board. The PCB containing the AD5601/AD5611/AD5621
should have separate analog and digital sections, each having its
own area of the board. If the AD5601/AD5611/AD5621 are in a
system where other devices require an AGND-to-DGND
connection, the connection should be made at one point only.
This ground point should be as close as possible to the
AD5601/AD5611/AD5621.
The power supply to the AD5601/AD5611/AD5621 should be
bypassed with 10 μF and 0.1 μF capacitors. The capacitors
should be physically as close as possible to the device, with the
0.1 μF capacitor ideally right up against the device. The 10 μF
capacitors are the tantalum bead type. It is important that the
0.1 μF capacitor have low effective series resistance (ESR) and
effective series inductance (ESI), such as in common ceramic
types of capacitors. This 0.1 μF capacitor provides a low impedance path to ground for high frequencies caused by transient
currents due to internal logic switching.
The power supply line itself should have as large a trace as
possible to provide a low impedance path and reduce glitch
effects on the supply line. Clocks and other fast switching
digital signals should be shielded from other parts of the board
by digital ground. Avoid crossover of digital and analog signals,
if possible. When traces cross on opposite sides of the board,
ensure that they run at right angles to each other to reduce
feedthrough effects on the board. The best board layout technique is the microstrip technique, where the component side of
the board is dedicated to the ground plane only and the signal
traces are placed on the solder side. However, this is not always
possible with a two-layer board.
Rev. H | Page 19 of 21
AD5601/AD5611/AD5621
Data Sheet
OUTLINE DIMENSIONS
2.20
2.00
1.80
1.35
1.25
1.15
6
5
4
1
2
3
2.40
2.10
1.80
0.65 BSC
1.00
0.90
0.70
1.10
0.80
0.10 MAX
COPLANARITY
0.10
SEATING
PLANE
0.30
0.15
0.40
0.10
0.46
0.36
0.26
0.22
0.08
072809-A
1.30 BSC
COMPLIANT TO JEDEC STANDARDS MO-203-AB
Figure 54. 6-Lead Thin Shrink Small Outline Transistor Package [SC70]
(KS-6)
Dimensions shown in millimeters
1.50
1.40
1.30
2.10
2.00
1.90
0.65 REF
4
PIN 1 INDEX
AREA
EXPOSED
PAD
0.45
0.40
0.35
TOP VIEW
0.80
0.75
0.70
SEATING
PLANE
0.203 REF
0.35
0.30
0.25
0.05 MAX
0.00 MIN
3
1
BOTTOM VIEW
0.20 MIN
1.70
1.60
1.50
PIN 1
INDICATOR
(R 0.15)
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COPLANARITY
0.08
COMPLIANT TO JEDEC STANDARDS MO-229
Figure 55. 6-Lead Lead Frame Chip Scale Package [LFCSP_WD]
2.00 × 3.00 mm Body, Very Very Thin, Dual Lead
(CP-6-5)
Dimensions shown in millimeters
Rev. H | Page 20 of 21
03-29-2012-B
3.10
3.00
2.90
6
Data Sheet
AD5601/AD5611/AD5621
ORDERING GUIDE
Model1
AD5601BKSZ-500RL7
AD5601BKSZ-REEL7
AD5601BCPZ-RL7
AD5611AKSZ-500RL7
AD5611AKSZ-REEL7
AD5611ACPZ-RL7
AD5611BKSZ-500RL7
AD5611BKSZ-REEL7
AD5621AKSZ-500RL7
AD5621AKSZ-REEL7
AD5621ACPZ-RL7
AD5621BKSZ-500RL7
AD5621BKSZ-REEL7
EVAL-AD5621EBZ
1
Temperature
Range
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
INL
±0.5 LSB
±0.5 LSB
±0.5 LSB
±4.0 LSB
±4.0 LSB
±4.0 LSB
±0.5 LSB
±0.5 LSB
±6.0 LSB
±6.0 LSB
±6.0 LSB
±1.0 LSB
±1.0 LSB
Package Description
6-Lead Thin Shrink Small Outline Transistor Package [SC70]
6-Lead Thin Shrink Small Outline Transistor Package [SC70]
6-Lead Lead Frame Chip Scale Package [LFCSP_WD]
6-Lead Thin Shrink Small Outline Transistor Package [SC70]
6-Lead Thin Shrink Small Outline Transistor Package [SC70]
6-Lead Lead Frame Chip Scale Package[LFCSP_WD]
6-Lead Thin Shrink Small Outline Transistor Package [SC70]
6-Lead Thin Shrink Small Outline Transistor Package [SC70]
6-Lead Thin Shrink Small Outline Transistor Package [SC70]
6-Lead Thin Shrink Small Outline Transistor Package [SC70]
6-Lead Lead Frame Chip Scale Package[LFCSP_WD]
6-Lead Thin Shrink Small Outline Transistor Package [SC70]
6-Lead Thin Shrink Small Outline Transistor Package [SC70]
Evaluation Board
Z = RoHS Compliant Part.
©2005–2016 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D06853-0-2/16(H)
Rev. H | Page 21 of 21
Package
Option
KS-6
KS-6
CP-6-5
KS-6
KS-6
CP-6-5
KS-6
KS-6
KS-6
KS-6
CP-6-5
KS-6
KS-6
Branding
D3V
D3V
89
D3U
D3U
8B
D3T
D3T
D3S
D3S
D3S
D3R
D3R