Classification Part Name REFERENCE SPECIFICATION Round Type 2R Light Touch Switch Issue No. Part No. EVQ11K05B 20151337 1 / 10 1. Notification Items 1.1 Law and the regulation which are applied ① Ozone depleting substances specified by Montreal Protocol have not been used in the manufacturing process of the material used in this product. ② This product complies with RoHS Directive (on the restriction of the use of certain hazardous substances in electrical and electronic equipment) (2011/65/EU). ③ The materials used in this product contain only the substances listed in the List of Existing Chemical Substances specified in ‘Act on the Evaluation of Chemical Substances and Regulation of Their Manufacture, etc’. ④ Permission must be obtained from the Japanese government if the product that is subject to the "Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan. 1.2 Application Limits The following shall be described for safety precaution: [Limitation of Application] - This product has been designed and manufactured for general electronic devices, such as home electronics, office equipment, information device and communication devices. In an event that this product is used for more sophisticated applications requiring higher safety and reliability and its failure or malfunction of this product may impose damage to human life or property, agreement on product specifications for approval suitable for such applications are required. Such applications shall include the following: aircraft equipment, aerospace equipment, disaster prevention / crime prevention equipment, medical equipment, transportation equipment (vehicles, trains, ships, etc.), information processing equipment that are highly publicized, and other equivalent equipment - Regardless of its applications, in an event that this product is used for the equipment requiring high safety levels, place protective circuits or redundant circuits and perform safety tests to improve your products safety. 1.3 Handling of reference specification. ・ Since the contents of this reference specification are subjected to change without prior notifications,please request us a formal specification again for your investigations before using. 1.4 Manufacturing Sites The country of manufacture : Malaysia The country of manufacture : China The country of manufacture : Japan Panasonic Industrial Devices Malaysia Sdn. Bhd. Panasonic Industrial Devices (Qingdao) Co., Ltd. Input Devices Business Unit, Electromechanical Control Business Division Panasonic Corporation 2. Summary 2.1 This specifications applies to the following types of switch. Push-ON type S.P.S.T 2.2 This specifications is a constituent document of contract for business concluded between your company and Panasonic Corporation. 2.3 Items not particularly specified in this specifications shall be in conformance with JIS Standards. Panasonic Corporation Classification Part Name Issue No. REFERENCE SPECIFICATION Round Type 2R Light Touch Switch 20151337 Part No. EVQ11K05B 3. Dimension・Marking・Circuit diagram 2 / 10 REFERENCE ONLY Date code are indicated in the product. Panasonic Corporation Classification Part Name Round Type 2R Light Touch Switch REFERENCE SPECIFICATION Part No. EVQ11K05B Panasonic Corporation Issue No. 20151337 3 / 10 Classification Part Name Issue No. REFERENCE SPECIFICATION Round Type 2R Light Touch Switch 20151337 Part No. 4 / 10 EVQ11K05B 4. General specification DC 15 V 20 mA(max.) 4.1 Switch rating DC 2 V 10 μA(min.) -20 ∼ + 70 ℃ 4.2 Operation temperature range 4.3 Preservative temperature range Single condition : Taping condition: - 40 ∼ + 85 ℃ - 20 ∼ + 40 ℃ 4.4 Standard conditions Unless otherwise specified, the test and measurements shall be carried out as follows. 5 ∼ 35 ℃ Ambient temperature : 45 ∼ 85 % Relative humidity : 86 ∼ 106 kPa Atmospheric pressure : However, if doubt arises on the decision based on the measured values under the above-mentioned conditions, the following conditions shall be employed. 20 ± 2 ℃ Ambient temperature : 65 ± 5 % Relative humidity : 86 ∼ 106 kPa Atmospheric pressure : 5. Performance 5.1 Electrical characteristics No. ITEM 5.1.1 Contact TEST CONDITION Push force : resistance Measurement tool : {Operation force} × 2 PERFORMANCE 50 mΩ max. Contact resistance meter (Capable of 10 μA ∼ 10 mA) 5.1.2 5.1.3 5.1.4 Insulation DC 100 V (Between terminals) resistance Withstand AC 250 V for 1 minute. (Between terminals) voltage Bouncing Operation speed : 3∼4 times/s 50 MΩ min. No insulation destruction ON 3 ms max. bounce_e OFF 8 ms max. Panasonic Corporation Classification Part Name Issue No. REFERENCE SPECIFICATION Round Type 2R Light Touch Switch 20151337 Part No. 5 / 10 EVQ11K05B 5.2 Mechanical characteristics No. ITEM PERFORMANCE TEST CONDITION 5.2.1 Operation force Push force 1.3 dousazu2_e 5.2.2 + - 0.4 0.4 N Return force 0.2 N min Travel to Push by recommended operating condition.(4.2) closure F={Operation force}×2 0.25 + - 0.1 0.1 mm storoke_zu 5.2.3 50 N for Push strength 60 sec. No damage push_zu (Electrical and mechanical) 5.2.4 Pull strength pull_zu 5.2.5 Vibration test 20 N min. 1) Amplitude : 1.5 mm No.5.1 and 2) Sweep rate : 10-55-10Hz for 1 minute 5.2.1 to 5.2.2 shall 3) Sweep method : Logarithmic frequency be satisfied. sweep rate 4) Vibration direction : X,Y,Z(3 directions) 5) Time : Each direction 2 hours (Total 6 hours) 5.2.6 Soldering heat Soldering area : 1/2 of P.W.B. thickness test Soldering temperature : 260±5℃ No damage (Electrical and Soldering time : 5±1 sec. 5.2.7 Solderbility mechanical) After spreading flux, the terminal is immersed 95% or more of surface in solder with following condition. area(Excluding ruptured Solder bar surface)where is : M705/Sn-3.0Ag-0.5Cu (Senju Metal Industry Co.,Ltd.) Flux : CF-110VH-2A (tamura kaken) Soldering temperture : 260±5℃ Soldering time : 2±0.5 sec. Panasonic Corporation immersed in solder shall be covered by new solder. Classification Part Name REFERENCE SPECIFICATION Round Type 2R Light Touch Switch Issue No. 20151337 Part No. 6 / 10 EVQ11K05B 5.3 Climatic characteristics No. ITEM TEST CONDITION 5.3.1 Cold test 1) Temperature : -40±2 ℃ PERFORMANCE Contact resistance 2) Duration of test : 500h 200 mΩ max. 3) Take off a drop water. No.5.1.2 to 5.1.4 and 4) Standard conditions after test : 1h No.5.2.1 to 5.2.2 shall be satisfied. 5.3.2 Heat test 1) Temperature : 85±2 ℃ Contact resistance 2) Duration of test : 500h 200 mΩ max. 3) Standard conditions after test : 1h No.5.1.2 to 5.1.4 and No.5.2.1 to 5.2.2 shall be satisfied. 5.3.3 Heat shock 1) Test cycles test 5.3.4 Humidity test : 20 cycles 2) Standard conditions after test 1) Temperature Contact resistance : 1h A:+85±2 ℃ B:-40±2 ℃ C:1 hour D:5 minutes max. E:1 hour F:5 minutes max. : 60±2 ℃ No.5.2.1 to 5.2.2 shall be satisfied. 2) Relative humidity : 90∼95 % 200 mΩ max. 3) Duration of test No.5.1.2 to 5.1.4 and : 500 h No.5.2.1 to 5.2.2 5) Standard conditions after test : 1h Endurance 1) DC 15 V (Switching 2) Operation speed : 2∼3 times/s 3) Push force : Maximum value of operation action) No.5.1.2 to 5.1.4 and Contact resistance 4) Take off a drop water. 5.3.5 200 mΩ max. 20 mA Resistance load force 4) Operation number : shall be satisfied. Contact resistance 20 Ω max. Bouncing : 10 ms max. Variation rate of 1,000,000 times operation force shall be within ±30 % to the value before testing No.5.1.2 and 5.2.2 shall be satisfied. 5.3.6 Withstand H 2S 1) Density : 3±1ppm Contact resistance 2) Temperature : 40±2 ℃ 200 mΩ max. 3) Relative humidity : 80∼85 % No.5.1.2 to 5.1.4 and 4) Duration of test No.5.2.1 to 5.2.2 : 24 h 5) Standard conditions after test : 1h Panasonic Corporation shall be satisfied. Classification Part Name REFERENCE SPECIFICATION Round Type 2R Light Touch Switch Issue No. Part No. EVQ11K05B 20151337 7 / 10 6. Prohibitions and precaution for handling 6.1 Soldering condition ITEM CONDITION Preheat temperature 110 ℃ max.(Environmental temperature of soldering surface of P.W.B.) Preheat time 60 sec. max. Area of flux 1/2 max. of P.W.B. thickness Temperature of solder 260±5 ℃ Time of immersion Within 5 sec. Soldering number Within 2 times (But should bring down heat of the first soldering.) Printed wiring board Single sided copper-clad laminates 1) After switches were soldered, please be careful not to clean switches with solvent. 2) Please flux don't into over the switch. 3) In the case of using soldering iron,soldering conditions shall be 350 ℃ max. 3 sec. max. 1 time only and the tip of iron must not touch to terminals. Soldering iron for re-soldering have to be 60 W max. 4) Right after switches were soldered, please be carefull not to load on the knobs of switches. 6.2 Design instructions 1) Please refer to the land pattern plan Panasonic recommends on the 2nd page. 2) Design key top as fig-1. Design inclination of key top 4 deg. max. as fig-2. (Recommended operation condition) tyuui3_e tyuui4_e fig-1 fig-2 6.3 Note 1) Please be cautions not to give excessive static load or shock to switches. 2) Please be careful not to pile up P.W.B. after switches were soldered. 3) A product shall be mounted properly by insert machine. 4) Preservation under high temperature and high humidity or corrosive gas should be avoided especially. When you need to preserve for a long period, do not open the carton. 5) Avoid the use of the switch under pushed ON condition is continued for a long time. Panasonic Corporation Classification Part Name Issue No. REFERENCE SPECIFICATION Round Type 2R Light Touch Switch 20151337 Part No. EVQ11K05B 7. Packing and taping Specifications 7.1 Packing method Packing method :Taped products should be put into the inner packing case like zigzag. Packing quantity :Inner carton 2,500 pcs. Outer carton 25,000 pcs. 7.2 Method of draw out hou1_tate0_e hou1_tate0_e 7.3 Taping condition 1) Lack of products (1) Middle portion Shoud not continue 4 pcs. hou2 (2) The end of taping Should have more than 5 pitch leader space. hou3 (3) Bending part At bending part , one product can be skipped. hou4_e 2) In case of cutting the lead wire off,the length of lead wire protruded from the tape is maximum 2 mm. hou5 3) Pull strength Pull strength products should not be separated from the tape at the pull strength of 5N. (Direction A) hou6 Pull strength products should not be separated from the tape at the pull strength of 1N. (Direction B ,3 sec) Panasonic Corporation 8 / 10 Classification Part Name REFERENCE SPECIFICATION Round Type 2R Light Touch Switch Part No. EVQ11K05B 4) Connecting portion The connecting portion and number is free. The connection between the mount tape shall be done with adhesive tapes. Connecting portion should be less than 4 time thick, compared with the other portion. (1) Adhesive tape The strength of connection should satisfy the specification of 7.3 3) and adhesive tape should not block pilot holes. (2) Ground tape The connection between the mount tape shall be done with the adhesive tape and the gap between tapes is maximum 0.5 mm. Adhesive tape should not block pilot holes. 7.4 Bending portion The tape should be bent every 25 pitch. The portion of bending is free. 7.5 Marking of packing(Inner carton) A: Customer part No. Panasonic part No. Quantity B: Direction of products Panasonic Corporation Issue No. 20151337 9 / 10 Classification Part Name REFERENCE SPECIFICATION Round Type 2R Light Touch Switch Issue No. Part No. EVQ11K05B 20151337 10 / 10 <Prohibitions and precaution for handling> 【Prohibited items on fire and smoking】 ・ Absolutely avoid use of a product beyond its rated range because doing so may cause a fire. If misuse or abnormal use may result under conditions in which the product is used out of its rated range, take proper measures such as current interruption using a protective circuit. ・ The grade of nonflammability for resin used in product is "94HB, " which is based on UL94 Standards (flammability test for plastic materials). Prohibit use in a location where a spreading fire may be generated or prepare against a spreading fire. 【For use in equipment for which safety is requested】 ・ Although care is taken to ensure product quality, inferior characteristics, short circuits, and open circuits are some problems that might be generated. To design an equipment which places maximum emphasis on safety, review the effect of any single fault of a product in advance and perform virtually fail-safe design to ensure maximum safety by: ・ Preparing a protective circuit or a protective device to improve system safety, and equipment. ・ Preparing a redundant circuit to improve system safety so that the single fault of a product does not cause a dangerous situation. 【Attentions required for storage condition】 ・ When this product is to be stored in the following circumstances and conditions, it may affect on the performance deteriorations and solderability etc., avoid storing in the following conditions. (1) A place where the temperature is -10℃ max., +40℃ min. and the humidity is 85% min. (2) In the corrosive gas atmosphere. (3) Long-term storage for 6 months min. (4) A place where the product is exposed to direct sunlight. ・ Store in packed condition so that the load stress is not applied. ・ Please use this product as soon as possible, our recommendation is within 3 months and the limitation is 6 months. ・ If any remainder left after packing is opened, store it with proper moistureproofing and gasproofing, etc., ・ The switch shall be packed by Nylon sheet in the box like original packaging style when it will be an inventory after using on the assembly machine at your production line. Panasonic Corporation