ADV7123-EP: Enhanced Product Data Sheet (Rev. 0) PDF

CMOS, 170 MHz, Triple, 10-Bit
High Speed Video DAC
ADV7123-EP
FEATURES
APPLICATIONS
Digital video systems
High resolution color graphics
Digital radio modulation
Image processing
Instrumentation
Video signal reconstruction
FUNCTIONAL BLOCK DIAGRAM
VAA
BLANK
BLANK AND
SYNC LOGIC
SYNC
IOR
R9 TO R0
10
DATA
REGISTER
10
DAC
G9 TO G0
10
DATA
REGISTER
10
DAC
DATA
REGISTER
10
B9 TO B0
PSAVE
10
IOR
IOG
IOG
IOB
DAC
IOB
VOLTAGE
REFERENCE
CIRCUIT
POWER-DOWN
MODE
CLOCK
VREF
ADV7123-EP
GND
RSET COMP
09200-001
170 MSPS throughput rate
Triple, 10-bit digital-to-analog converters (DACs)
SFDR
−70 dB at fCLK = 50 MHz; fOUT = 1 MHz
−53 dB at fCLK = 140 MHz; fOUT = 40 MHz
RS-343A-/RS-170-compatible output
Complementary outputs
DAC output current range: 2.0 mA to 26.5 mA
TTL-compatible inputs
Internal reference: 1.235 V
Single-supply 3.3 V operation
48-lead LFCSP package
Low power dissipation: 30 mW minimum at 3 V
Low power standby mode: 6 mW typical at 3 V
Supports defense and aerospace applications
(AQEC standard)
Military temperature range: −55°C to +105°C
Controlled manufacturing baseline
One assembly/test site
One fabrication site
Enhanced product change notification
Qualification data available on request
Figure 1.
GENERAL DESCRIPTION
The ADV7123-EP is a triple, high speed digital-to-analog
converter (DAC) on a single monolithic chip. It consists of three
high speed, 10-bit video DACs with complementary outputs,
a standard TTL input interface, and a high impedance, analog
output current source.
The ADV7123-EP has three separate 10-bit-wide input ports.
A single 3.3 V power supply and clock are the only components
required to make the part functional. The ADV7123-EP has
additional video control signals: composite SYNC and BLANK.
The ADV7123-EP also has a power save mode.
The ADV7123-EP is fabricated in a 5 V CMOS process. Its
monolithic CMOS construction ensures greater functionality
with lower power dissipation. The ADV7123-EP is available
in a 48-lead LFCSP package.
Full details about this enhanced product are available in the
ADV7123 data sheet, which should be consulted in conjunction
with this data sheet.
PRODUCT HIGHLIGHTS
1.
2.
Guaranteed monotonic to 10 bits.
Compatible with a wide variety of high resolution color
graphics systems, including RS-343A and RS-170.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2010 Analog Devices, Inc. All rights reserved.
ADV7123-EP
TABLE OF CONTENTS
Features .............................................................................................. 1 Timing Specifications ...................................................................5 Applications ....................................................................................... 1 Absolute Maximum Ratings ............................................................7 Functional Block Diagram .............................................................. 1 ESD Caution...................................................................................7 General Description ......................................................................... 1 Pin Configuration and Function Descriptions..............................8 Product Highlights ........................................................................... 1 Outline Dimensions ....................................................................... 10 Revision History ............................................................................... 2 Ordering Guide .......................................................................... 10 Specifications..................................................................................... 3 Dynamic Specifications ............................................................... 4 REVISION HISTORY
7/10—Revision 0: Initial Version
Rev. 0 | Page 2 of 12
ADV7123-EP
SPECIFICATIONS
VAA = 3.0 V to 3.6 V, VREF = 1.235 V, RSET = 560 Ω, CL = 10 pF. All specifications TMIN to TMAX, 1 unless otherwise noted; TJ MAX = 110°C.
Table 1.
Parameter 2
STATIC PERFORMANCE
Resolution (Each DAC)
Integral Nonlinearity (BSL)
Differential Nonlinearity
DIGITAL AND CONTROL INPUTS
Input High Voltage, VIH
Input Low Voltage, VIL
Input Current, IIN
PSAVE Pull-Up Current
Input Capacitance, CIN
ANALOG OUTPUTS
Output Current
DAC-to-DAC Matching
Output Compliance Range, VOC
Output Impedance, ROUT
Output Capacitance, COUT
Offset Error
Gain Error 3
VOLTAGE REFERENCE, EXTERNAL
Reference Range, VREF
VOLTAGE REFERENCE, INTERNAL
Voltage Reference, VREF
POWER DISSIPATION
Digital Supply Current 4
Analog Supply Current
Standby Supply Current
Power Supply Rejection Ratio
Min
Typ
Max
Unit
Test Conditions/Comments1
−1
−1
+0.5
+0.25
10
+1
+1
Bits
LSB
LSB
RSET = 680 Ω
RSET = 680 Ω
RSET = 680 Ω
+1
V
V
μA
μA
pF
VIN = 0.0 V or VDD
2.0
0.8
−1
20
10
2.0
2.0
26.5
18.5
1.0
0
1.4
70
10
0
0
1.12
0
1.235
1.35
1.235
2.2
6.5
7.5
67
8
2.1
0.1
mA
mA
%
V
kΩ
pF
% FSR
% FSR
Green DAC, SYNC = high
RGB DAC, SYNC = low
Tested with DAC output = 0 V
FSR = 17.62 mA
V
V
5.0
12.0
13.5
72
5.0
0.5
1
mA
mA
mA
mA
mA
mA
%/%
fCLK = 50 MHz
fCLK = 140 MHz
fCLK = 170 MHz
RSET = 560 Ω
RSET = 4933 Ω
PSAVE = low, digital and control inputs at VDD
Temperature range TMIN to TMAX: −55°C to +105°C.
These maximum/minimum specifications are guaranteed by characterization over the 3.0 V to 3.6 V range.
Gain error = {(Measured (FSC)/Ideal (FSC) − 1) × 100}, where Ideal (FSC) = VREF/RSET × K × (0x3FFH) and K = 7.9896.
4
Digital supply is measured with a continuous clock that has data input corresponding to a ramp pattern and with an input level at 0 V and VDD.
2
3
Rev. 0 | Page 3 of 12
ADV7123-EP
DYNAMIC SPECIFICATIONS
VAA = 3.0 V to 3.6 V, VREF = 1.235 V, RSET = 680 Ω, CL = 10 pF. All specifications are at TA = 25°C, unless otherwise noted; TJ MAX = 110°C.
Table 2.
Parameter 1
AC LINEARITY
Spurious-Free Dynamic Range to Nyquist 2
Single-Ended Output
fCLK = 50 MHz; fOUT = 1.00 MHz
fCLK = 50 MHz; fOUT = 2.51 MHz
fCLK = 50 MHz; fOUT = 5.04 MHz
fCLK = 50 MHz; fOUT = 20.2 MHz
fCLK = 100 MHz; fOUT = 2.51 MHz
fCLK = 100 MHz; fOUT = 5.04 MHz
fCLK = 100 MHz; fOUT = 20.2 MHz
fCLK = 100 MHz; fOUT = 40.4 MHz
fCLK = 140 MHz; fOUT = 2.51 MHz
fCLK = 140 MHz; fOUT = 5.04 MHz
fCLK = 140 MHz; fOUT = 20.2 MHz
fCLK = 140 MHz; fOUT = 40.4 MHz
Double-Ended Output
fCLK = 50 MHz; fOUT = 1.00 MHz
fCLK = 50 MHz; fOUT = 2.51 MHz
fCLK = 50 MHz; fOUT = 5.04 MHz
fCLK = 50 MHz; fOUT = 20.2 MHz
fCLK = 100 MHz; fOUT = 2.51 MHz
fCLK = 100 MHz; fOUT = 5.04 MHz
fCLK = 100 MHz; fOUT = 20.2 MHz
fCLK = 100 MHz; fOUT = 40.4 MHz
fCLK = 140 MHz; fOUT = 2.51 MHz
fCLK = 140 MHz; fOUT = 5.04 MHz
fCLK = 140 MHz; fOUT = 20.2 MHz
fCLK = 140 MHz; fOUT = 40.4 MHz
Spurious-Free Dynamic Range Within a Window
Single-Ended Output
fCLK = 50 MHz; fOUT = 1.00 MHz; 1 MHz Span
fCLK = 50 MHz; fOUT = 5.04 MHz; 2 MHz Span
fCLK = 140 MHz; fOUT = 5.04 MHz; 4 MHz Span
Double-Ended Output
fCLK = 50 MHz; fOUT = 1.00 MHz; 1 MHz Span
fCLK = 50 MHz; fOUT = 5.00 MHz; 2 MHz Span
fCLK = 140 MHz; fOUT = 5.00 MHz; 4 MHz Span
Total Harmonic Distortion
fCLK = 50 MHz; fOUT = 1.00 MHz
TA = 25°C
TMIN to TMAX
fCLK = 50 MHz; fOUT = 2.00 MHz
fCLK = 100 MHz; fOUT = 2.00 MHz
fCLK = 140 MHz; fOUT = 2.00 MHz
Min
Rev. 0 | Page 4 of 12
Typ
Max
Unit
67
67
63
55
62
60
54
48
57
58
52
41
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
70
70
65
54
67
63
58
52
62
61
55
53
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
77
73
64
dBc
dBc
dBc
74
73
60
dBc
dBc
dBc
66
65
64
64
55
dBc
dBc
dBc
dBc
dBc
ADV7123-EP
Parameter 1
DAC PERFORMANCE
Glitch Impulse
DAC-to-DAC Crosstalk 3
Data Feedthrough 4, 5
Clock Feedthrough4, 5
Min
Typ
Max
10
23
22
33
Unit
pV-sec
dB
dB
dB
1
These maximum/minimum specifications are guaranteed by characterization over the 3.0 V to 3.6 V range.
The ADV7123-EP exhibits high performance when operating with an internal voltage reference, VREF.
DAC-to-DAC crosstalk is measured by holding one DAC high while the other two DACs are making low-to-high and high-to-low transitions.
4
Clock and data feedthrough is a function of the amount of overshoot and undershoot on the digital inputs. Glitch impulse includes clock and data feedthrough.
5
TTL input values are 0 V to 3 V, with input rise/fall times of 3 ns, measured at the 10% and 90% points. Timing reference points are 50% for inputs and outputs.
2
3
TIMING SPECIFICATIONS
VAA = 3.0 V to 3.6 V, VREF = 1.235 V, RSET = 560 Ω, CL = 10 pF. All specifications TMIN to TMAX, 1 unless otherwise noted; TJ MAX = 110°C.
Table 3.
Parameter 2, 3
ANALOG OUTPUTS
Analog Output Delay
Analog Output Rise/Fall Time 4
Analog Output Transition Time 5
Analog Output Skew 6
CLOCK CONTROL
CLOCK Frequency 7
Data and Control Setup
Data and Control Hold
CLOCK Period
CLOCK Pulse Width High6
CLOCK Pulse Width Low6
Pipeline Delay6
PSAVE Up Time6
Symbol
Min
t6
t7
t8
t9
fCLK
t1
t2
t3
t4
t5
tPD
t10
Typ
7.5
1.0
15
1
Max
Unit
2
ns
ns
ns
ns
170
0.68
2.9
5.88
2.6
2.6
1.0
1.0
4
1
1.0
10
MHz
ns
ns
ns
ns
ns
Clock cycles
ns
Test Conditions/Comments
fCLK_MAX = 170 MHz
fCLK_MAX = 170 MHz
Temperature range TMIN to TMAX: −55°C to +105°C.
These maximum/minimum specifications are guaranteed by characterization over the 3.0 V to 3.6 V range.
Timing specifications are measured with input levels of 3.0 V (VIH) and 0 V (VIL).
4
Rise time was measured from the 10% to 90% point of zero to full-scale transition, fall time from the 90% to 10% point of a full-scale transition.
5
Measured from the 50% point of full-scale transition to within 2% of the final output value.
6
Guaranteed by characterization.
7
fCLK maximum specification production tested at 125 MHz.
2
3
Rev. 0 | Page 5 of 12
ADV7123-EP
t3
t4
t5
CLOCK
t2
DIGITAL INPUTS
(R9 TO R0, G9 TO G0, B9 TO B0,
SYNC, BLANK)
t1
t6
t8
ANALOG INPUTS
(IOR, IOR, IOG, IOG, IOB, IOB)
NOTES
1. OUTPUT DELAY (t6) MEASURED FROM THE 50% POINT OF THE RISING EDGE OF CLOCK TO THE 50% POINT
OF FULL-SCALE TRANSITION.
2. OUTPUT RISE/FALL TIME (t7) MEASURED BETWEEN THE 10% AND 90% POINTS OF FULL-SCALE TRANSITION.
3. TRANSITION TIME (t8) MEASURED FROM THE 50% POINT OF FULL-SCALE TRANSITION TO WITHIN 2% OF THE
FINAL OUTPUT VALUE.
Figure 2. Timing Diagram
Rev. 0 | Page 6 of 12
09200-002
t7
ADV7123-EP
ABSOLUTE MAXIMUM RATINGS
Table 4.
Parameter
VAA to GND
Voltage on Any Digital Pin
Ambient Operating Temperature (TA)
Storage Temperature (TS)
Junction Temperature (TJ)
Lead Temperature (Soldering, 10 sec)
Vapor Phase Soldering (1 Minute)
IOUT to GND1
1
Rating
7V
GND − 0.5 V to VAA + 0.5 V
−55°C to +105°C
−65°C to +150°C
150°C
300°C
220°C
0 V to VAA
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
Analog output short circuit to any power supply or common GND can be of
an indefinite duration.
Rev. 0 | Page 7 of 12
ADV7123-EP
48
47
46
45
44
43
42
41
40
39
38
37
R9
R8
R7
R6
R5
R4
R3
R2
R1
R0
PSAVE
RSET
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
PIN 1
INDICATOR
ADV7123-EP
TOP VIEW
(Not to Scale)
36
35
34
33
32
31
30
29
28
27
26
25
VREF
COMP
IOR
IOR
IOG
IOG
VAA
VAA
IOB
IOB
GND
GND
09200-003
VAA
B0
B1
B2
B3
B4
B5
B6
B7
B8
B9
CLOCK
13
14
15
16
17
18
19
20
21
22
23
24
G0 1
G1 2
G2 3
G3 4
G4 5
G5 6
G6 7
G7 8
G8 9
G9 10
BLANK 11
SYNC 12
NOTES
1. THE EXPOSED PADDLE ON THE UNDERSIDE OF THE PACKAGE
MUST BE SOLDERED TO THE GROUND PLANE TO INCREASE THE
RELIABILITY OF THE SOLDER JOINTS AND TO MAXIMIZE THE
THERMAL CAPABILITY OF THE PACKAGE.
Figure 3. Pin Configuration
Table 5. Pin Function Descriptions
Pin No.
1 to 10,
14 to 23,
39 to 48
11
Mnemonic
G0 to G9,
B0 to B9,
R0 to R9
BLANK
12
SYNC
13, 29, 30
24
VAA
CLOCK
25, 26
27, 31, 33
GND
IOB, IOG, IOR
28, 32, 34
IOB, IOG, IOR
35
COMP
36
VREF
Description
Red, Green, and Blue Pixel Data Inputs (TTL Compatible). Pixel data is latched on the rising edge of CLOCK.
R0, G0, and B0 are the least significant data bits. Unused pixel data inputs should be connected to either the
regular printed circuit board (PCB) power or ground plane.
Composite Blank Control Input (TTL Compatible). A Logic 0 on this control input drives the analog outputs—
IOR, IOB, and IOG—to the blanking level. The BLANK signal is latched on the rising edge of CLOCK. When
BLANK is a Logic 0, the R0 to R9, G0 to G9, and B0 to B9 pixel inputs are ignored.
Composite Sync Control Input (TTL Compatible). A Logic 0 on the SYNC input switches off a 40 IRE current
source. The sync current is internally connected to the IOG analog output. SYNC does not override any other
control or data input; therefore, it should only be asserted during the blanking interval. SYNC is latched on
the rising edge of CLOCK. If sync information is not required on the green channel, the SYNC input should be
tied to Logic 0.
Analog Power Supply (3.3 V ± 10%). All VAA pins on the ADV7123-EP must be connected.
Clock Input (TTL Compatible). The rising edge of CLOCK latches the R0 to R9, G0 to G9, B0 to B9, SYNC, and
BLANK pixel and control inputs. Typically, the CLOCK input is the pixel clock rate of the video system. CLOCK
should be driven by a dedicated TTL buffer.
Ground. The GND pins must be connected.
Differential Red, Green, and Blue Current Outputs (High Impedance Current Sources). These RGB video outputs
are specified to directly drive RS-343A and RS-170 video levels into a doubly terminated 75 Ω coaxial cable.
If the complementary outputs are not required, these outputs should be tied to ground.
Red, Green, and Blue Current Outputs (High Impedance Current Sources). These RGB video outputs are specified
to directly drive RS-343A and RS-170 video levels into a doubly terminated 75 Ω coaxial cable. All three current
outputs should have similar output loads whether or not they are all being used.
Compensation Pin for the Internal Reference Amplifier. A 0.1 μF ceramic capacitor must be connected
between COMP and VAA.
Voltage Reference Input for DACs or Voltage Reference Output (1.235 V). The VREF pin is normally terminated
to VAA through a 0.1 μF capacitor. However, the ADV7123-EP can be overdriven by an external 1.23 V reference
(AD1580), if required.
Rev. 0 | Page 8 of 12
ADV7123-EP
Pin No.
37
Mnemonic
RSET
38
EP
PSAVE
Exposed Pad
Description
A resistor (RSET) connected between this pin and GND controls the magnitude of the full-scale video signal.
Note that the IRE relationships are maintained, regardless of the full-scale output current. For nominal video
levels into a doubly terminated 75 Ω load, RSET = 530 Ω.
The relationship between RSET and the full-scale output current on IOG (assuming ISYNC is connected to IOG) is
given by
RSET (Ω) = 11,445 × VREF (V)/IOG (mA)
The relationship between RSET and the full-scale output current on IOR, IOG, and IOB is given by
IOG (mA) = 11,445 × VREF (V)/RSET (Ω) (SYNC being asserted)
IOR, IOB (mA) = 7989.6 × VREF (V)/RSET (Ω)
The equation for IOG is the same as that for IOR and IOB when SYNC is not being used, that is, SYNC is tied
permanently low.
Power Save Control Pin. Reduced power consumption is available on the ADV7123-EP when this pin is active.
The exposed paddle on the underside of the package must be soldered to the ground plane to increase the
reliability of the solder joints and to maximize the thermal capability of the package.
Rev. 0 | Page 9 of 12
ADV7123-EP
OUTLINE DIMENSIONS
0.30
0.23
0.18
PIN 1
INDICATOR
48
37
36
1
0.50
BSC
TOP VIEW
0.80
0.75
0.70
0.45
0.40
0.35
4.25
4.10 SQ
3.95
EXPOSED
PAD
12
25
24
13
BOTTOM VIEW
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
SEATING
PLANE
PIN 1
INDICATOR
0.25 MIN
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-WKKD.
112408-A
7.00
BSC SQ
Figure 4. 48-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
7 mm × 7 mm Body, Very Very Thin Quad
(CP-48-5)
Dimensions shown in millimeters
ORDERING GUIDE
Model 1
ADV7123SCP170EP-RL
1
Temperature Range
−55°C to +105°C
Speed Option
170 MHz
Available in 3.3 V version only.
Rev. 0 | Page 10 of 12
Package Description
48-Lead LFCSP_WQ
Package Option
CP-48-5
ADV7123-EP
NOTES
Rev. 0 | Page 11 of 12
ADV7123-EP
NOTES
©2010 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D09200-0-7/10(0)
Rev. 0 | Page 12 of 12