BAT15... Silicon Schottky Diodes • Low barrier type for DBS mixer applications up to 12 GHz, phase detectors and modulators • Low noise figure • Pb-free (RoHS compliant) package 1) • Qualified according AEC Q101 BAT15-02LRH BAT15-03W BAT15-04W BAT15-05W ! , BAT15-099 BAT15-099LRH " ! , , " ! , , , ! , , ! , " , BAT15-099R ESD (Electrostatic discharge) sensitive device, observe handling precaution! Type BAT15-02LRH BAT15-03W BAT15-04W BAT15-05W BAT15-07LRH BAT15-098LRH BAT15-099 BAT15-099R BAT15-099LRH 1Pb-containing Package TSLP-2-7 SOD323 SOT323 SOT323 TSLP-4-7 TSLP-4-7 SOT143 SOT143 TSLP-4-7 Configuration single, leadless single series common cathode parallel pair, leadless anti-parallel pair, leadless anti-parallel pair cross-over ring anti-parallel pair, leadless LS(nH) 0.4 1.8 1.4 1.4 0.4 0.4 2 2 0.4 Marking NP white P S8s S5s NP B S5s S6s S5 package may be available upon special request 1 2010-03-05 BAT15... Maximum Ratings at TA = 25°C, unless otherwise specified Parameter Symbol Value Diode reverse voltage VR 4 Forward current IF 110 Total power dissipation Ptot Unit V mA mW BAT15-02LRH, -099LRHTS ≤ 76 °C 100 BAT15-03W, TS ≤ 70 °C 100 BAT15-04W, TS ≤ 68 °C 100 BAT15-05W, TS ≤ 65 °C 100 BAT15-099, TS ≤ 48 °C 100 BAT15-099R, TS ≤ 67 °C 100 150 Junction temperature Tj Operating temperature range T op -55 ... 150 Storage temperature T stg -55 ... 150 °C Thermal Resistance Parameter Symbol Junction - soldering point 1) RthJS Value K/W BAT15-02LRH, -099LRH ≤ 780 BAT15-03W ≤ 795 BAT15-04W ≤ 820 BAT15-05W ≤ 850 BAT15-099 ≤ 1020 ≤ 830 BAT15-099R 1For Unit calculation of RthJA please refer to Application Note Thermal Resistance 2 2010-03-05 BAT15... Electrical Characteristics at TA = 25°C, unless otherwise specified Parameter Symbol Values Unit min. typ. max. 4 - - IF = 1 mA 0.16 0.23 0.32 IF = 10 mA 0.25 0.32 0.41 - - 20 DC Characteristics Breakdown voltage V(BR) V I(BR) = 100 µA Forward voltage VF Forward voltage matching1) ∆ VF mV IF = 10 mA AC Characteristics Diode capacitance pF CT VR = 0 V, f = 1 MHz, all other types - - 0.35 VR = 0 V, f = 1 MHz, BAT15-099R - - 0.5 - 5.5 - Differential forward resistance RF Ω I F = 10 mA / 50 mA 1∆V F is the difference between lowest and highest V F in a multiple diode component. 3 2010-03-05 BAT15... Diode capacitance CT = ƒ (VR) f = 1MHz Reverse current IR = ƒ(VR) TA = Parameter EHD07082 0.5 CT ΙR pF EHD07081 3 10 µA T A =125 C 0.4 10 2 10 1 85 C 0.3 25 C 0.2 10 0 0.1 0.0 10 0 2 V -1 0 4 1 2 3 Forward current IF = ƒ (VF) Forward current IF = ƒ (T S) TA = Parameter BAT15-02LRH, BAT15-099LRH EHD07077 120 mA mA 100 10 1 90 TA = -40 ˚C 25 ˚C 85 ˚C 125 ˚C 10 80 IF ΙF BAT 15-099R 4 VR VR 10 2 V 0 70 60 50 40 10 -1 30 20 10 10 -2 0.0 0.5 0 0 V 1.0 15 30 45 60 75 90 105 120 °C 150 TS VF 4 2010-03-05 BAT15... Forward current IF = ƒ (T S) Forward current IF = ƒ (T S) BAT15-03W BAT15-04W 120 120 mA 100 100 90 90 80 80 IF IF mA 70 70 60 60 50 50 40 40 30 30 20 20 10 10 0 0 15 30 45 60 75 90 105 120 °C 0 0 150 15 30 45 60 75 90 105 120 °C TS Forward current IF = ƒ (T S) Forward current IF = ƒ (T S) BAT15-05W BAT15-099 120 120 mA mA 100 100 90 90 80 80 IF IF 150 TS 70 70 60 60 50 50 40 40 30 30 20 20 10 10 0 0 15 30 45 60 75 90 105 120 °C 0 0 150 TS 15 30 45 60 75 90 105 120 °C 150 TS 5 2010-03-05 BAT15... Forward current IF = ƒ (T S) BAT15-099R 120 mA 100 90 IF 80 70 60 50 40 30 20 10 0 0 15 30 45 60 75 90 105 120 °C 150 TS Permissible Puls Load RthJS = ƒ (tp) Permissible Pulse Load BAT15-02LRH, BAT15-099LRH IFmax / I FDC = ƒ (t p) BAT15-02LRH, BAT15-099LRH 10 3 10 1 RthJS 0.5 0.2 0.1 0.05 0.02 0.01 0.005 D=0 10 2 10 1 -7 10 IFmax/IFDC K/W 10 -6 10 -5 10 -4 10 -3 10 -2 s 10 D=0 0.005 0.01 0.02 0.05 0.1 0.2 0.5 10 0 -6 10 0 tp 10 -5 10 -4 10 -3 10 -2 s 10 0 tp 6 2010-03-05 BAT15... Permissible Puls Load RthJS = ƒ (tp) Permissible Pulse Load BAT15-03W IFmax / I FDC = ƒ (t p) BAT15-03W 10 3 10 1 RthJS I Fmax/IFDC K/W D=0.5 0.2 0.1 0.05 0.02 0.01 0.005 0 10 2 10 1 -6 10 10 -5 10 -4 10 -3 D=0 0.005 0.01 0.02 0.05 0.1 0.2 0.5 10 -2 s 10 10 0 -6 10 0 10 -5 10 -4 10 -3 10 -2 tp s 10 0 10 0 tp Permissible Puls Load RthJS = ƒ (tp) Permissible Pulse Load BAT15-04W IFmax / I FDC = ƒ (t p) BAT15-04W 10 3 10 1 RthJS IFmax/IFDC K/W D=0.5 0.2 0.1 0.05 0.02 0.01 0.005 0 10 2 10 1 -6 10 10 -5 10 -4 10 -3 D=0 0.005 0.01 0.02 0.05 0.1 0.2 0.5 10 -2 s 10 10 0 -6 10 0 tp 10 -5 10 -4 10 -3 10 -2 s tp 7 2010-03-05 BAT15... Permissible Puls Load RthJS = ƒ (tp) Permissible Pulse Load BAT15-05W IFmax / I FDC = ƒ (t p) BAT15-05W 10 3 10 1 RthJS I Fmax/IFDC K/W D=0.5 0.2 0.1 0.05 0.02 0.01 0.005 0 10 2 10 1 -6 10 10 -5 10 -4 10 -3 D=0 0.005 0.01 0.02 0.05 0.1 0.2 0.5 10 -2 s 10 10 0 -6 10 0 10 -5 10 -4 10 -3 10 -2 tp s 10 0 10 0 tp Permissible Puls Load RthJS = ƒ (tp) Permissible Pulse Load BAT15-099 IFmax / I FDC = ƒ (t p) BAT15-099 10 3 10 1 RthJS IFmax/IFDC K/W 10 10 1 -6 10 D=0 0.005 0.01 0.02 0.05 0.1 0.2 0.5 D=0.5 0.2 0.1 0.05 0.02 0.01 0.005 0 2 10 -5 10 -4 10 -3 10 -2 s 10 10 0 -6 10 0 tp 10 -5 10 -4 10 -3 10 -2 s tp 8 2010-03-05 BAT15... Permissible Puls Load RthJS = ƒ (tp) Permissible Pulse Load BAT15-099R IFmax / I FDC = ƒ (t p) BAT15-099R 10 3 10 1 RthJS I Fmax/IFDC K/W D=0.5 0.2 0.1 0.05 0.02 0.01 0.005 0 10 2 10 1 -6 10 D=0 0.005 0.01 0.02 0.05 0.1 0.2 0.5 10 -5 10 -4 10 -3 10 -2 s 10 10 0 -6 10 0 tp 10 -5 10 -4 10 -3 10 -2 s 10 0 tp 9 2010-03-05 BAT15... S11-Parameters for BAT15-099 Typical impedance characteristics (with external bias I and Zo = 50Ω) f I = 0.02 mA I = 0.05 mA I = 0.1 mA I = 0.2 mA I = 0.5 mA GHz MAG ANG MAG ANG MAG ANG MAG ANG MAG ANG 1 0.94 -16.4 0.84 -16.6 0.77 -16.4 0.59 -17.2 0.19 -16.7 2 0.93 -33.8 0.88 -33.8 0.77 -34.5 0.58 -35.2 0.15 -36.1 3 0.92 -53.8 0.86 -54.5 0.75 -54.1 0.58 -56.1 0.13 -64.8 4 0.91 -74.3 0.84 -75.3 0.72 -76.4 0.51 -78.4 0.11 -104.8 5 0.91 -96.6 0.84 -97.6 0.72 -99.1 0.53 -102.3 0.15 -135.7 6 0.91 -115.4 0.84 -116.7 0.73 -118.7 0.53 -122.9 0.18 -160.9 7 0.91 -131 0.84 -132.3 0.73 -134.1 0.54 -138.1 0.2 -168.8 8 0.91 -143 0.84 -144.5 0.73 -146.8 0.55 -150.5 0.81 179.4 9 0.91 -155.6 0.83 -150.2 0.71 -159.7 0.53 -163.9 0.18 179.4 10 0.9 -167.3 0.83 -169.7 0.71 -178.8 0.51 -175.8 0.14 151.2 11 0.89 175.5 0.8 172.6 0.7 170 0.45 164.9 0.09 105.5 12 0.88 175.5 0.76 146.5 0.62 142.8 0.39 134.2 0.14 43.6 S11 = (f, I) BAT15-099 + j 50 + j 100 + j 25 0.02 mA 12 Hz 0.05 mA + j 10 0.1 mA + j 250 0.2 mA f 0.5 mA 0 10 25 50 100 Ω 250 1 GHz - j 250 - j10 8 GHz - j 100 - j 25 5 GHz - j50 EHD07083 10 2010-03-05 Package SOD323 11 BAT15... 2010-03-05 Package SOT143 BAT15... 2 0.1 MAX. 10˚ MAX. 1 1 ±0.1 0.2 0.8 +0.1 -0.05 0.4 +0.1 -0.05 A 5 0...8˚ 0.2 M A 0.25 M B 1.7 0.08...0.1 1.3 ±0.1 3 2.4 ±0.15 4 B 10˚ MAX. 2.9 ±0.1 1.9 0.15 MIN. Package Outline Foot Print 1.2 0.8 0.9 1.1 0.9 0.8 1.2 0.8 0.8 Marking Layout (Example) RF s 56 Manufacturer Pin 1 2005, June Date code (YM) BFP181 Type code Standard Packing Reel ø180 mm = 3.000 Pieces/Reel Reel ø330 mm = 10.000 Pieces/Reel 0.2 2.6 8 4 Pin 1 3.15 1.15 12 2010-03-05 Package SOT323 BAT15... Package Outline 0.9 ±0.1 2 ±0.2 0.3 +0.1 -0.05 0.1 MAX. 3x 0.1 M 0.1 A 1 2 1.25 ±0.1 0.1 MIN. 2.1 ±0.1 3 0.15 +0.1 -0.05 0.65 0.65 0.2 M A Foot Print 0.8 1.6 0.6 0.65 0.65 Marking Layout (Example) Manufacturer 2005, June Date code (YM) BCR108W Type code Pin 1 Standard Packing Reel ø180 mm = 3.000 Pieces/Reel Reel ø330 mm = 10.000 Pieces/Reel 0.2 2.3 8 4 Pin 1 2.15 1.1 13 2010-03-05 Package TSLP-2-7 BAT15... Package Outline Top view Bottom view 0.39 +0.01 -0.03 0.6 ±0.05 0.05 MAX. 1 1 0.25 ±0.035 1) 2 1±0.05 0.65 ±0.05 2 0.5 ±0.035 1) Cathode marking 1) Dimension applies to plated terminal Foot Print 0.45 Copper Solder mask 0.375 0.35 0.275 1 0.925 0.3 0.35 0.6 0.275 For board assembly information please refer to Infineon website "Packages" Stencil apertures Marking Layout (Example) BAR90-02LRH Type code Cathode marking Laser marking Standard Packing Reel ø180 mm = 15.000 Pieces/Reel Reel ø330 mm = 50.000 Pieces/Reel (optional) 0.5 Cathode marking 8 1.16 4 0.76 14 2010-03-05 Package TSLP-4-7 BAT15... Package Outline Bottom view 0.8 ±0.05 4 x 0.25 ±0.035 1) 0.75 ±0.05 0.05 MAX. 3 2 4 1 2 3 1 1.2 ±0.05 0.39 +0.01 -0.03 4 x 0.35 ±0.035 1) Top view 4 0.45 ±0.05 Pin 1 marking 1) Dimension applies to plated terminal Foot Print For board assembly information please refer to Infineon website "Packages" 0.8 0.4 0.38 0.42 1.18 0.4 1.2 0.4 0.38 0.78 0.28 0.3 0.28 0.3 0.22 0.2 Copper Stencil apertures Solder mask Marking Layout (Example) BAR90-07LRH Type code Pin 1 marking Laser marking Standard Packing Reel ø180 mm = 15.000 Pieces/Reel 0.5 1.45 8 4 Pin 1 marking 1.05 15 2010-03-05 BAT15... Edition 2009-11-16 Published by Infineon Technologies AG 81726 Munich, Germany 2009 Infineon Technologies AG All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (<www.infineon.com>). Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. 16 2010-03-05