PulseGuard® Suppressors Surface Mount Polymeric ESD Suppressors PGB1 Series Halogen-Free / Lead-Free Description PulseGuard ESD Suppressors help protect sensitive electronic equipment against electrostatic discharge (ESD). They supplement the on-chip protection of integrated circuitry and are best suited for low-voltage, high-speed applications where low capacitance is important. Data ports utilizing such high-speed protocols as USB 2.0, IEEE1394, HDMI and DVI can benefit from this new technology. PulseGuard suppressors use polymer composite materials to suppress fast-rising ESD transients (as specified in IEC 61000-4-2), while adding virtually no capacitance to the circuit. Equivalent Circuits Features SOT23 Device 0402 and 0603 Devices t3P)4DPNQMJBOUMFBEGSFF and available halogen-free t6MUSBMPXDBQBDJUBODF t-PXMFBLBHFDVSSFOU t'BTUSFTQPOTFUJNF t#JEJSFDUJPOBM 3 2 1 1 2 t8JUITUBOETNVMUJQMF &4%TUSJLFT t$PNQBUJCMFXJUI QJDLBOEQMBDFQSPDFTTFT t"WBJMBCMFJO 5000 and 10000 piece SFFMT&*"34 Applications Part Number Lines Protected Component Package Available as Halogen-Free PGB1010402 1 0402 /P1 PGB1010603 1 0603 Yes PGB102ST23 2 SOT23 Yes t%JHJUBM$BNFSB t&YUFSOBM4UPSBHF t4FU5PQ#PY t"OUFOOB t)%57)BSEXBSF t-BQUPQ%FTLUPQ Computer t/FUXPSL)BSEXBSF t$PNQVUFS1FSJQIFSBMT Product Characteristics Electrical Characteristics Specification PGB1010402 PGB1010603 PGB102ST23 L7 L7 L7 L7 L7 L7 1FBL7PMUBHFUZQJDBM 1000V 500V 500V Clamping Voltage (typical) 250V 150V 150V 3BUFE7PMUBHFNBYJNVN 12VDC 24VDC 24VDC Capacitance (typical) Q' Q' Q' <1nS <1nS <1nS -FBLBHF$VSSFOUUZQJDBM O"7%$ O"7%$ O"7%$ &4%1VMTF8JUITUBOE 100 pulses min 1000 pulses min 1000 pulses min ESD Capability: IEC 61000-4-2 Contact Discharge *&$"JS%JTDIBSHF 3FTQPOTF5JNF Notes Measured per IEC 61000-4-2 L7$POUBDU%JTDIBSHF2 Measured per IEC 61000-4-2 L7$POUBDU%JTDIBSHF2, at 25 nsec. Measured at 250 MHz Some shifting in characteristics may occur when tested over multiple pulses at a very rapid rate /PUFT1(#QSPEVDUOPUPGGFSFEBT)BMPHFO'SFF4FF1(#TFSJFTQSPEVDUJOTUFBEIUUQXXXMJUUFMGVTFDPNTFSJFT1(#IUNM 5FTUJOHQFSGPSNFEPO-JUUFMGVTFUFTUTFUVQBTEFTDSJCFEJO5ZQJDBM5FTU4FUVQ4FDUJPOPOQBHFPGUIJTEPDVNFOU PGB1 Series Specifications are subject to change without notice. 1 Revised: January 11, 2012 www.littelfuse.com ©2011 Littelfuse PulseGuard® Suppressors Surface Mount Polymeric ESD Suppressors Part Numbering System Dimensions PGB1 01 0603 MR 0402 Device Dimensions: mm (inch) LEAD-FREE PULSEGUARD® ESD SUPPRESSORS 0.15 +/- 0.08 (0.006" +/- 0.003") 0.310 +/- 0.08 (0.012" +/- 0.003") 0.25 (0.010") LINES PROTECTED: 01 = 1 line 02 = 2 lines 0.99 +/- 0.05 (0.039" +/- 0.002") 0.24 +/- 0.09 (0.009" +/- 0.004") DEVICE SIZE CODE: 0402 = 0402 (1005)* 0603 = 0603 (1608) ST23 = SOT23 0.51 +/- 0.05 (0.020" +/- 0.002") Reflow Solder QUANTITY & PACKAGING CODE: MR = 1000 pieces, tape & reel WR = 3000 pieces, tape & reel NR = 5000 pieces, tape & reel KR = 10,000 pieces, tape & reel Recommended for reflow soldering only 1.55 (0.061") 0.38 (0.015") .58 (0.023") 0.56 (0.022") *Note: PGB1 0402 product not available as Halogen Free item. See PGB2 0402 product instead, part number PGB2010402KRHF (http://www.littelfuse.com/series/PGB2010402.html). 0603 Device Typical Device Capacitance Dimensions: mm (inch) 1.66 +/- 0.06 (0.066" +/- 0.003”) 1.04 (0.041") REF Capacitance (pF) 1.00 0.36 (0.014") 0.15 +/- 0.08 (0.006" +/- 0.003”) 0.84 +/- 0.05 (0.033" +/- 0.002”) 0.43 +/- 0.18 (0.017" +/- 0.007”) PGB102ST23 0.10 Wave Solder Reflow Solder PGB1010603 PGB1010402 0.51 (0.020") 0.76 (0.030") 3.30 (0.130") 3.05 (0.120") 1.27 (0.050") 0.01 100 1,000 10,000 1.27 (0.050") 0.76 (0.030") 0.76 (0.030") Frequency (MHz) SOT23 Device Typical ESD Response Dimensions: mm (inch) 2.24 +/- 0.18 (0.088" +/- 0.007") 1200 3.00 +/- 0.20 (0.118" +/- 0.008") Voltage (V) 1000 1.09 (0.043") 0.69 +/- 0.10 (0.027" +/- 0.004) 800 600 PGB1010402 200 0.91 (0.036") TYP 0.81 (0.032") TYP PGB1010603 PGB102ST23 400 0.15 +/- 0.08 (0.006 +/- 0.003") TYP Reflow Solder 1.02 (0.040") 0 -25 1.91 (0.075") 0 25 50 75 100 125 150 1.27 (0.050") 175 2.29 (0.090") Time (ns) 1.02 (0.040") 0.64 (0.025") 0.51 (0.020") PGB1 Series Specifications are subject to change without notice. Wave Solder 1.02 (0.040") 2 Revised: January 11, 2012 1.02 (0.040") 1.27 (0.050") 2.54 (0.100") 1.27 (0.050") 0.64 (0.025") 2.03 (0.080") 2.29 (0.090") www.littelfuse.com ©2011 Littelfuse PulseGuard® Suppressors Surface Mount Polymeric ESD Suppressors Physical Specifications Environmental Specifications Materials #PEZ(MBTT&QPYZ 5FSNJOBUJPOT$PQQFS/JDLFM5JO Solderability .*-45%.FUIPE Operating Temperature Moisture Resistance Soldering Parameters 8BWFTPMEFS¡$TFDPOETNBYJNVN 3FnPXTPMEFS¡$TFDPOETNBYJNVN 0402 series: ¡$3)IPVST 0603, ST23: ¡$3)IPVST Thermal Shock .*-45%.FUIPE -65°C to 125°C, 30 min. cycle, 10 cycles Vibration .*-45%.FUIPE to 55 to 10 Hz, 1 min. cycle, 2 hrs each in X-Y-Z) Chemical Resistance .*-45%.FUIPE Solder Leach Resistance and Terminal Adhesion *1$&*"+45% Design Consideration Because of the fast rise-time of the ESD transient, proper QMBDFNFOUPG1VMTF(VBSETVQQSFTTPSTBSFBLFZEFTJHO consideration to achieving optimal ESD suppression. The devices should be placed on the circuit board as close to the source of the ESD transient as possible. Install PulseGuard TVQQSFTTPSTDPOOFDUFEGSPNTJHOBMEBUBMJOFUPHSPVOE directly behind the connector so that they are the first boardlevel circuit component encountered by the ESD transient. -65°C to +125°C Soldering Parameters Reflow Condition Pre Heat 1Co'SFFBTTFNCMZ - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) oTFDPOET Average ramp up rate (Liquidus Temp (TL) to peak ¡$TFDPOENBY TS(max) to TL - Ramp-up Rate ¡$TFDPOENBY Reflow - Temperature (TL) (Liquidus) - Temperature (tL) ¡$ 60 – 150 seconds Peak Temperature (TP) 260°C Time within 5°C of actual peak Temperature (tp) 10 – 30 seconds Ramp-down Rate ¡$TFDPOENBY Time 25°C to peak Temperature (TP) NJOVUFTNBY PGB1 Series Specifications are subject to change without notice. #BTFEPO*1$+&%&$+45% 3 Revised: January 11, 2012 www.littelfuse.com ©2011 Littelfuse PulseGuard® Suppressors Surface Mount Polymeric ESD Suppressors Packaging Quantity & Packaging Code Quantity Packaging Option Packaging Specification PGB1010402 ,3 10000 5BQF3FFMwSFFM &*"34*&$QBSU PGB1010603 .3 1000 5BQF3FFMwSFFM &*"34*&$QBSU PGB102ST23 83 3000 5BQF3FFMwSFFM &*"34*&$QBSU PGB1010603 /3 5000 5BQF3FFMwSFFM &*"34*&$QBSU Part Number Tape and Reel Specifications Tt Ds D T P P P Ps Ct Description 0402 Series (mm) 0603 Series SOT23 Series (mm) (mm) Ct$PWFSUBQFUIJDLOFTT 0.05 0.05 Dd - Drive hole diameter 1.50 1.50 1.50 Ds - Drive hole spacing 4.00 4.00 4.00 Pd1PDLFUEFQUI 0.41 1.02 Ph1PDLFUIFJHIU 1.12 3.23 Ps1PDLFUTQBDJOH 2.00 4.00 4.00 Pw1PDLFUXJEUI 0.62 1.02 2.46 0.06 Tt$BSSJFSUBQFUIJDLOFTT 0.61 0.65 Tw - Carrier tape width Typical Test Setup FARADAY CAGE COMPUTER AGILENT INFINIIUM 1.5 GHz 8 GS/s 30dB PASTERNAK ATTENUATOR PE7025-30 TEKTRONIX LOW CAP PROBE 6158 (20x TIP) QUADTECH 1865 RESISTANCE METER RESISTANCE TEST FIXTURE ESD TEST FIXTURE TEST BOARD W/ DUT ESD PULSE GENERATOR PGB1 Series Specifications are subject to change without notice. 4 Revised: January 11, 2012 www.littelfuse.com ©2011 Littelfuse