PHILIPS HEF4066BT

HEF4066B
Quad single-pole single-throw analog switch
Rev. 7 — 16 November 2011
Product data sheet
1. General description
The HEF4066B provides four single-pole, single-throw analog switch functions. Each
switch has two input/output terminals (nY and nZ) and an active HIGH enable input (nE).
When nE is LOW, the analog switch is turned off.
The HEF4066B is pin compatible with the HEF4016B but exhibits a much lower ON
resistance. In addition the ON resistance is relatively constant over the full input signal
range.
2. Features and benefits






Fully static operation
5 V, 10 V, and 15 V parametric ratings
Standardized symmetrical output characteristics
Inputs and outputs are protected against electrostatic effects
Specified from 40 C to +85 C and 40 C to +125 C
Complies with JEDEC standard JESD 13-B
3. Applications
 Analog multiplexing and demultiplexing
 Digital multiplexing and demultiplexing
 Signal gating
4. Ordering information
Table 1.
Ordering information
Type number
Package
Temperature range
Name
Description
Version
HEF4066BP
40 C to +125 C
DIP14
plastic dual in-line package; 14 leads (300 mil)
SOT27-1
HEF4066BT
40 C to +125 C
SO14
plastic small outline package; 14 leads;
body width 3.9 mm
SOT108-1
HEF4066B
NXP Semiconductors
Quad single-pole single-throw analog switch
5. Functional diagram
1Y
1E
2Y
2E
3Y
3E
4Y
4E
1
2
1Z
13
nY
4
3
2Z
nE
5
8
9
3Z
VDD
11
10
4Z
12
VSS
001aag200
Fig 1.
VDD
6
nZ
001aag201
Functional diagram
Fig 2.
Logic diagram (one switch)
6. Pinning information
6.1 Pinning
1Y
1
14 VDD
1Z
2
13 1E
2Z
3
12 4E
2Y
4
HEF4066B 11 4Y
2E
5
10 4Z
3E
6
9
3Z
VSS
7
8
3Y
001aag202
Fig 3.
Pin configuration
6.2 Pin description
Table 2.
Pin description
Symbol
Pin
Description
1Y, 2Y, 3Y, 4Y
1, 4, 8, 11
independent input or output
1Z, 2Z, 3Z, 4Z
2, 3, 9, 10
independent input or output
1E, 2E, 3E, 4E
13, 5, 6, 12
enable input (active HIGH)
VSS
7
ground (0 V)
VDD
14
supply voltage
HEF4066B
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 16 November 2011
© NXP B.V. 2011. All rights reserved.
2 of 16
HEF4066B
NXP Semiconductors
Quad single-pole single-throw analog switch
7. Functional description
Table 3.
Function table[1]
Input nE
Switch
H
ON
L
OFF
[1]
H = HIGH voltage level; L = LOW voltage level.
8. Limiting values
Table 4.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to VSS = 0 V (ground).
Symbol
Parameter
VDD
supply voltage
IIK
input clamping current
VI
input voltage
Conditions
VI < 0.5 V or VI > VDD + 0.5 V
Min
Max
Unit
0.5
+18
V
-
10
mA
0.5
VDD + 0.5
V
II/O
input/output current
-
10
mA
Tstg
storage temperature
65
+150
C
Tamb
ambient temperature
40
+85
C
Ptot
total power dissipation
P
[1]
power dissipation
[1]
Tamb = 40 C to +85 C
DIP14
[2]
-
750
mW
SO14
[3]
-
500
mW
-
100
mW
per switch
To avoid drawing VDD current out of terminal nZ, when switch current flows into terminals nY, the voltage drop across the bidirectional
switch must not exceed 0.4 V. If the switch current flows into terminal nZ, no VDD current will flow out of terminals nY, in this case there
is no limit for the voltage drop across the switch, but the voltages at nY and nZ may not exceed VDD or VSS.
[2]
For DIP14 packages: above Tamb = 70 C, Ptot derates linearly with 12 mW/K.
[3]
For SO14 packages: above Tamb = 70 C, Ptot derates linearly with 8 mW/K.
9. Recommended operating conditions
Table 5.
Recommended operating conditions
Symbol
Parameter
VDD
supply voltage
VI
input voltage
Tamb
ambient temperature
in free air
t/V
input transition rise and fall
rate
HEF4066B
Product data sheet
Conditions
Min
Typ
Max
Unit
3
-
15
V
0
-
VDD
V
40
-
+125
C
VDD = 5 V
-
-
3.75
s/V
VDD = 10 V
-
-
0.5
s/V
VDD = 15 V
-
-
0.08
s/V
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 16 November 2011
© NXP B.V. 2011. All rights reserved.
3 of 16
HEF4066B
NXP Semiconductors
Quad single-pole single-throw analog switch
10. Static characteristics
Table 6.
Static characteristics
VSS = 0 V; VI = VSS or VDD unless otherwise specified.
Symbol Parameter
Conditions
VDD
Tamb = 40 C Tamb = 25 C
Min
VIH
VIL
HIGH-level
input voltage
LOW-level
input voltage
IO < 1 A
input leakage
current
IS(OFF)
OFF-state
leakage
current
IDD
supply current all valid input
combinations
CI
input
capacitance
per channel;
see Figure 4
nE input
Min
Max
Min
Max
Min
Max
5V
3.5
-
3.5
-
3.5
-
3.5
-
V
10 V
7.0
-
7.0
-
7.0
-
7.0
-
V
15 V
11.0
-
11.0
-
11.0
-
11.0
-
V
5V
-
1.5
-
1.5
-
1.5
-
1.5
V
10 V
-
3.0
-
3.0
-
3.0
-
3.0
V
15 V
-
4.0
-
4.0
-
4.0
-
4.0
V
15 V
-
0.1
-
0.1
-
1.0
-
1.0
A
15 V
-
-
-
200
-
-
-
-
nA
5V
-
1.0
-
1.0
-
7.5
-
7.5
A
10 V
-
2.0
-
2.0
-
15.0
-
15.0
A
15 V
-
4.0
-
4.0
-
30.0
-
30.0
A
-
-
-
-
7.5
-
-
-
-
pF
IO < 1 A
II
Max
Tamb = 85 C Tamb = 125 C Unit
10.1 Test circuit
VDD
nE
VIL
nZ
VI
nY
IS
VSS
VO
001aak669
Fig 4.
Test circuit for measuring OFF-state leakage current
HEF4066B
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 16 November 2011
© NXP B.V. 2011. All rights reserved.
4 of 16
HEF4066B
NXP Semiconductors
Quad single-pole single-throw analog switch
10.2 ON resistance
Table 7.
ON resistance
Tamb = 25 C; ISW = 200 A; VSS = 0 V.
Symbol
Parameter
Conditions
RON(peak)
ON resistance (peak)
VI = 0 V to VDD; see Figure 5 and
Figure 6
RON(rail)
ON resistance (rail)
VDD
Typ
Max
Unit
5V
350
2500

10 V
80
245

15 V
60
175

5V
115
340

10 V
50
160

15 V
40
115

5V
120
365

10 V
65
200

15 V
50
155

VI = 0 V; see Figure 5 and Figure 6
VI = VDD; see Figure 5 and Figure 6
RON
ON resistance mismatch
between channels
5V
25
-

10 V
10
-

15 V
5
-

VI = 0 V to VDD; see Figure 5
10.2.1 ON resistance waveform and test circuit
001aak671
400
RON
(Ω)
(1)
300
VSW
200
VDD
nE
VIH
100
nY
VI
nZ
(2)
VSS
(3)
ISW
0
0
5
10
15
VI (V)
001aak670
ISW = 200 A.
RON = VSW / ISW.
(1) VDD = 5 V
(2) VDD = 10 V
(3) VDD = 15 V
Fig 5.
Test circuit for measuring RON
HEF4066B
Product data sheet
Fig 6.
Typical RON as a function of input voltage
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 16 November 2011
© NXP B.V. 2011. All rights reserved.
5 of 16
HEF4066B
NXP Semiconductors
Quad single-pole single-throw analog switch
11. Dynamic characteristics
Table 8.
Dynamic characteristics
Tamb = 25 C; VSS = 0 V; for test circuit see Figure 9.
Symbol
Parameter
Conditions
VDD
tPHL
HIGH to LOW propagation delay nY, nZ to nZ, nY; see Figure 7
nY, nZ to nZ, nY; see Figure 7
tPHZ
tPZH
tPLZ
tPZL
HIGH to OFF-state
propagation delay
nE to nY, nZ; see Figure 8
OFF-state to HIGH
propagation delay
nE to nY, nZ; see Figure 8
LOW to OFF-state
propagation delay
nE to nY, nZ; see Figure 8
OFF-state to LOW
propagation delay
nE to nY, nZ; see Figure 8
Typ
Max
Unit
5V
10
20
ns
10 V
5
10
ns
15 V
5
10
ns
5V
10
20
ns
10 V
5
10
ns
15 V
5
10
ns
5V
80
160
ns
10 V
65
130
ns
15 V
60
120
ns
5V
40
80
ns
10 V
20
40
ns
15 V
15
30
ns
5V
80
160
ns
10 V
70
140
ns
15 V
70
140
ns
5V
45
90
ns
10 V
20
40
ns
15 V
15
30
ns
Table 9.
Dynamic power dissipation PD
PD can be calculated from the formulas shown; VSS = 0 V; tr = tf  20 ns; Tamb = 25 C.
Symbol
PD
Parameter
dynamic power
dissipation
VDD
5V
Typical formula for PD (W)
where:
PD = 2500  fi + (fo  CL)  VDD
2
fi = input frequency in MHz;
10 V
PD = 11500  fi + (fo  CL)  VDD2
fo = output frequency in MHz;
15 V
PD = 29000  fi + (fo  CL) 
CL = output load capacitance in pF;
VDD2
VDD = supply voltage in V;
(CL  fo) = sum of the outputs.
HEF4066B
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 16 November 2011
© NXP B.V. 2011. All rights reserved.
6 of 16
HEF4066B
NXP Semiconductors
Quad single-pole single-throw analog switch
11.1 Waveforms and test circuit
VI
input nY or nZ
VM
VM
tPLH
tPHL
0V
VO
VM
output nZ or nY
VM
0V
001aak672
Measurement points are given in Table 10.
Fig 7.
nY or nZ to nZ or nY propagation delays
VI
VM
VM
input nE
0V
tPLZ
tPZL
VDD
90 %
output nY or nZ
10 %
0V
tPHZ
VDD
tPZH
90 %
output nY or nZ
10 %
0V
switch ON
switch OFF
switch ON
001aak673
Measurement points are given in Table 10.
Fig 8.
Enable and disable times
Table 10.
Measurement points
Supply voltage
Input
Output
VDD
VM
VM
5 V to 15 V
0.5VDD
0.5VDD
HEF4066B
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 16 November 2011
© NXP B.V. 2011. All rights reserved.
7 of 16
HEF4066B
NXP Semiconductors
Quad single-pole single-throw analog switch
VI
tW
90 %
negative
pulse
VM
0V
tf
tr
tr
tf
VI
90 %
positive
pulse
0V
VM
10 %
VM
VM
10 %
tW
VDD
VI
VI
VDD
VO
G
RL
S1
open
DUT
RT
CL
VSS
001aak674
Test data is given in Table 11.
Definitions:
DUT = Device Under Test.
RT = Termination resistance should be equal to output impedance Zo of the pulse generator.
CL = Load capacitance including test jig and probe.
RL = Load resistance.
Fig 9.
Test circuit for measuring switching times
Table 11.
Test data
Supply voltage
Input
Load
S1 position
VDD
VI
tr, tf
CL
RL
tPHL, tPLH
tPZH, tPHZ
tPZL, tPLZ
5 V to 15 V
0 V or VDD
20 ns
50 pF
10 k
VSS
VSS
VDD
11.2 Additional dynamic parameters
Table 12. Additional dynamic characteristics
VSS = 0 V; Tamb = 25 C.
Symbol
THD
Vct
Parameter
total harmonic distortion
crosstalk voltage
HEF4066B
Product data sheet
Conditions
VDD
see Figure 10; RL = 10 k; CL = 15 pF; 5 V
channel ON; VI = 0.5VDD (p-p);
10 V
fi = 1 kHz
15 V
nE input to switch; see Figure 11;
RL = 10 k; CL = 15 pF;
nE = VDD (square-wave)
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 16 November 2011
10 V
Typ
Max
Unit
[1]
0.25
-
%
[1]
0.04
-
%
[1]
0.04
-
%
50
-
mV
© NXP B.V. 2011. All rights reserved.
8 of 16
HEF4066B
NXP Semiconductors
Quad single-pole single-throw analog switch
Table 12. Additional dynamic characteristics …continued
VSS = 0 V; Tamb = 25 C.
Symbol
Parameter
Conditions
VDD
Typ
Max
Unit
50
-
dB
Xtalk
crosstalk
between switches; see Figure 12;
fi = 1 MHz; RL = 1 k;
VI = 0.5VDD (p-p)
10 V
[1]
iso
isolation (OFF-state)
see Figure 13; fi = 1 MHz; RL = 1 k;
CL = 5 pF; VI = 0.5VDD (p-p)
10 V
[1]
50
-
dB
f(3dB)
3 dB frequency response
see Figure 14; RL = 1 k; CL = 5 pF;
VI = 0.5VDD (p-p)
10 V
[1]
90
-
MHz
[1]
fi is biased at 0.5VDD.
11.2.1 Test circuits
VDD
nE
VIH
nY
nZ
VSS
fi
RL
CL
D
001aak675
Fig 10. Test circuit for measuring total harmonic distortion
0.5VDD
VDD
RL
nE
nY
nZ
VSS
G
RL
CL
V
VO
001aak676
a. Test circuit
logic
input nE
off
on
off
Vct
VO
001aak677
b. Input and output pulse definitions
Fig 11. Test circuit for measuring crosstalk voltage between digital input and switch
HEF4066B
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 16 November 2011
© NXP B.V. 2011. All rights reserved.
9 of 16
HEF4066B
NXP Semiconductors
Quad single-pole single-throw analog switch
VDD
1E
VIH
1Y or 1Z
1Z or 1Y
CHANNEL
ON
VI
RL
V
VO1
RL
V
VO2
nE
VIL
nY or nZ
nZ or nY
CHANNEL
OFF
RL
VSS
001aak678
20 log10 (VO2 / VO1) or 20 log10 (VO1 / VO2).
Fig 12. Test circuit for measuring crosstalk between switches
VDD
VDD
nE
VIL
nY
fi
nE
VIH
nZ
VSS
nY
RL
CL
dB
fi
001aak679
Adjust fi voltage to obtain 0 dBm level at input.
Fig 13. Test circuit for measuring isolation (OFF-state)
HEF4066B
Product data sheet
nZ
VSS
RL
CL
dB
001aak680
Adjust fi voltage to obtain 0 dBm level at output. Increase
fi frequency until dB meter reads 3 dB.
Fig 14. Test circuit for measuring frequency response
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 16 November 2011
© NXP B.V. 2011. All rights reserved.
10 of 16
HEF4066B
NXP Semiconductors
Quad single-pole single-throw analog switch
12. Package outline
DIP14: plastic dual in-line package; 14 leads (300 mil)
SOT27-1
ME
seating plane
D
A2
A
A1
L
c
e
Z
w M
b1
(e 1)
b
MH
8
14
pin 1 index
E
1
7
0
5
10 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
UNIT
A
max.
A1
min.
A2
max.
b
b1
c
D (1)
E (1)
e
e1
L
ME
MH
w
Z (1)
max.
mm
4.2
0.51
3.2
1.73
1.13
0.53
0.38
0.36
0.23
19.50
18.55
6.48
6.20
2.54
7.62
3.60
3.05
8.25
7.80
10.0
8.3
0.254
2.2
inches
0.17
0.02
0.13
0.068
0.044
0.021
0.015
0.014
0.009
0.77
0.73
0.26
0.24
0.1
0.3
0.14
0.12
0.32
0.31
0.39
0.33
0.01
0.087
Note
1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
JEITA
SOT27-1
050G04
MO-001
SC-501-14
EUROPEAN
PROJECTION
ISSUE DATE
99-12-27
03-02-13
Fig 15. Package outline SOT27-1 (DIP14)
HEF4066B
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 16 November 2011
© NXP B.V. 2011. All rights reserved.
11 of 16
HEF4066B
NXP Semiconductors
Quad single-pole single-throw analog switch
SO14: plastic small outline package; 14 leads; body width 3.9 mm
SOT108-1
D
E
A
X
c
y
HE
v M A
Z
8
14
Q
A2
A
(A 3)
A1
pin 1 index
θ
Lp
1
L
7
e
detail X
w M
bp
0
2.5
5 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (1)
e
HE
L
Lp
Q
v
w
y
Z (1)
mm
1.75
0.25
0.10
1.45
1.25
0.25
0.49
0.36
0.25
0.19
8.75
8.55
4.0
3.8
1.27
6.2
5.8
1.05
1.0
0.4
0.7
0.6
0.25
0.25
0.1
0.7
0.3
0.01
0.019 0.0100 0.35
0.014 0.0075 0.34
0.16
0.15
0.010 0.057
inches 0.069
0.004 0.049
0.05
0.244
0.039
0.041
0.228
0.016
0.028
0.024
0.01
0.01
0.028
0.004
0.012
θ
8o
o
0
Note
1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
SOT108-1
076E06
MS-012
JEITA
EUROPEAN
PROJECTION
ISSUE DATE
99-12-27
03-02-19
Fig 16. Package outline SOT108-1 (SO14)
HEF4066B
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 16 November 2011
© NXP B.V. 2011. All rights reserved.
12 of 16
HEF4066B
NXP Semiconductors
Quad single-pole single-throw analog switch
13. Revision history
Table 13.
Revision history
Document ID
Release date
Data sheet status
Change notice
Supersedes
HEF4066B v.7
20111116
Product data sheet
-
HEF4066B v.6
Modifications:
•
•
Legal pages updated.
Changes in “General description”, “Features and benefits” and “Applications”.
HEF4066B v.6
20100325
Product data sheet
-
HEF4066B v.5
HEF4066B v.5
20100225
Product data sheet
-
HEF4066B v.4
HEF4066B v.4
20091013
Product data sheet
-
HEF4066B_CNV v.3
HEF4066B_CNV v.3
19950101
Product specification
-
HEF4066B_CNV v.2
HEF4066B_CNV v.2
19950101
Product specification
-
-
HEF4066B
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 16 November 2011
© NXP B.V. 2011. All rights reserved.
13 of 16
HEF4066B
NXP Semiconductors
Quad single-pole single-throw analog switch
14. Legal information
14.1 Data sheet status
Document status[1][2]
Product status[3]
Definition
Objective [short] data sheet
Development
This document contains data from the objective specification for product development.
Preliminary [short] data sheet
Qualification
This document contains data from the preliminary specification.
Product [short] data sheet
Production
This document contains the product specification.
[1]
Please consult the most recently issued document before initiating or completing a design.
[2]
The term ‘short data sheet’ is explained in section “Definitions”.
[3]
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
14.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
14.3 Disclaimers
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors accepts no liability for inclusion and/or use of
NXP Semiconductors products in such equipment or applications and
therefore such inclusion and/or use is at the customer’s own risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the customer’s applications and
products planned, as well as for the planned application and use of
customer’s third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in life support, life-critical or
safety-critical systems or equipment, nor in applications where failure or
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from competent authorities.
HEF4066B
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 16 November 2011
© NXP B.V. 2011. All rights reserved.
14 of 16
HEF4066B
NXP Semiconductors
Quad single-pole single-throw analog switch
Non-automotive qualified products — Unless this data sheet expressly
states that this specific NXP Semiconductors product is automotive qualified,
the product is not suitable for automotive use. It is neither qualified nor tested
in accordance with automotive testing or application requirements. NXP
Semiconductors accepts no liability for inclusion and/or use of
non-automotive qualified products in automotive equipment or applications.
NXP Semiconductors’ specifications such use shall be solely at customer’s
own risk, and (c) customer fully indemnifies NXP Semiconductors for any
liability, damages or failed product claims resulting from customer design and
use of the product for automotive applications beyond NXP Semiconductors’
standard warranty and NXP Semiconductors’ product specifications.
In the event that customer uses the product for design-in and use in
automotive applications to automotive specifications and standards, customer
(a) shall use the product without NXP Semiconductors’ warranty of the
product for such automotive applications, use and specifications, and (b)
whenever customer uses the product for automotive applications beyond
14.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
15. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
HEF4066B
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 16 November 2011
© NXP B.V. 2011. All rights reserved.
15 of 16
HEF4066B
NXP Semiconductors
Quad single-pole single-throw analog switch
16. Contents
1
2
3
4
5
6
6.1
6.2
7
8
9
10
10.1
10.2
10.2.1
11
11.1
11.2
11.2.1
12
13
14
14.1
14.2
14.3
14.4
15
16
General description . . . . . . . . . . . . . . . . . . . . . . 1
Features and benefits . . . . . . . . . . . . . . . . . . . . 1
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Ordering information . . . . . . . . . . . . . . . . . . . . . 1
Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2
Pinning information . . . . . . . . . . . . . . . . . . . . . . 2
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 2
Functional description . . . . . . . . . . . . . . . . . . . 3
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 3
Recommended operating conditions. . . . . . . . 3
Static characteristics. . . . . . . . . . . . . . . . . . . . . 4
Test circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ON resistance . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ON resistance waveform and test circuit . . . . . 5
Dynamic characteristics . . . . . . . . . . . . . . . . . . 6
Waveforms and test circuit . . . . . . . . . . . . . . . . 7
Additional dynamic parameters . . . . . . . . . . . . 8
Test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 11
Revision history . . . . . . . . . . . . . . . . . . . . . . . . 13
Legal information. . . . . . . . . . . . . . . . . . . . . . . 14
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 14
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Contact information. . . . . . . . . . . . . . . . . . . . . 15
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2011.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
Date of release: 16 November 2011
Document identifier: HEF4066B