Datasheet

austriamicrosystems AG
is now
ams AG
The technical content of this austriamicrosystems datasheet is still valid.
Contact information:
Headquarters:
ams AG
Tobelbaderstrasse 30
8141 Unterpremstaetten, Austria
Tel: +43 (0) 3136 500 0
e-Mail: [email protected]
Please visit our website at www.ams.com
austriamicrosystems
Telephone Line Interface and
Speakerphone Circuit
AS2522B
DATA SHEET
-
impedance of 1000Ω) as well as a speech circuit with
softclipping, line loss compensation and Rx-volume control
for handset and handsfree operation. It shall act as an a/bline powered device, which is controlled by a CPU via a
serial interface. Furthermore the AS2522 incorporates a
DTMF, FSK transmitter, single tone and ringer tone
generator.
AS2522 allows to use an off-the-shelf microprocessor
without special blocks and functions for telephone
applications. DTMF, FSK transmitter, single tone and ringer
tone generator can be controlled via the serial interface as
well as the gain settings in handset and handsfree mode.
Applications
Enhanced handsfree feature phones with CallerID and
extended displays.
Package
Available in 32-pin TQFP
Te
ch
ni
ca
Block Diagram
AS2522 is a CMOS integrated circuit that incorporates DC
and AC line adaptation (DC-mask and synthesized AC-
al
id
-
Line/Speech circuit, DTMF dialer, FSK transmitter and
tone ringer on a 32-pin CMOS-IC
Enhanced voice switching
Background noise monitoring
DTMF tone generator
FSK Transmitter V.23, BELL202, V.21, BELL 103
Ringer tone programmable
Tx- and Rx-gain programmable
Digital volume control of Rx signals
DC characteristic programmable
Dual softclipping in handset mode
Tx-softclipping in handsfree mode
Common monitor amplifier for loudhearing, handsfree
and ringing
Supply voltage generation for external circuitry
Automatic line loss compensation (LLC)
Real and complex impedance selectable by external
components
Side tone adaptation selectable by external components
Unique EMC performance
Operating range from 15mA to 100mA (down to 5mA
with reduced performance)
Few external components
am
lc s
on A
te G
nt
st
il
-
General Description
lv
Key Features
Revision 3.4
Page 1 of 19
austriamicrosystems
Data Sheet AS2522B
Pin description
Pin #
Symbol
13
LS
Function
L ine Current S ense Input
Analog input for sensing the line current
10
LI
L ine I nput
11
RI
al
id
Analog input used for power extraction and line current sensing
R eceive I nput
Analog input for ac-separated receive signal
STB
S ide T one B alance Input
Analog input for side tone cancellation network
8
CS
C urrent S hunt Control Output
lv
7
14
CI
am
lc s
on A
te G
nt
st
il
N-channel open drain output to control the external high power shunt transistor for
synthesizing AC- and DC-impedance, modulation of line voltage and shorting the line during
make periods of pulse dialing
C omplex I mpedance Input
Analog input pin for the capacitor to program a complex impedance
12
SS
S upply S ource Control Output
N-channel open drain output to control the external high power source transistor for supplying
(Vpp) the loudspeaker amplifier in off-hook loudspeaking/handsfree mode
9
VSS
V oltage S ource S ource
Negative Analog Power Supply
18
VDD
V oltage D rain D rain
Positive Analog Power Supply
19
AGND
A nalog G round
6
M1
ca
Special ground for the internal amplifiers
M icrophone Input 1
Differential input for the handset microphone (electret)
M2
M icrophone Input 2
ni
4
ch
Differential input for the handset microphone (electret)
5
M3
M icrophone Input 3
Differential input for the handsfree microphone (electret)
Te
3
17
M4
M icrophone Input 4
Differential input for the handsfree microphone (electret)
RO
R eceive O utput to H andset
Output for driving a dynamic earpiece with an impedance from 150Ω to 300Ω
31
OSC
O scillator Input
Input for ceramic resonator 3.58MHz.
Revision 3.4
Page 2 of 19
austriamicrosystems
Data Sheet AS2522B
Pin #
Symbol
Function
22
VPP
Loudspeaker Power Supply
High power supply for the output driver stage
21
CM
C onverter M ake Output
27
xCS
C hip S elect
Chip select input of the serial interface. Internal pull-up resistor ( 100kOhm )
29
DI
D ata I nput
30
CLK
Cl oc k
lv
Data input of the serial interface. Internal pull-up resistor ( 100kOhm )
al
id
This is an output for controlling the external switching converter. During ringing it converts the
ring signal into a 4V supply voltage
Clock input of the serial interface. Internal pull-up resistor ( 100kOhm )
DO
D ata O utput
am
lc s
on A
te G
nt
st
il
28
Data output of the serial interface. If xCS=1 DO is in HI-Z state
24
23
LO1
LO2
1
FT1
2
FT2
20
CBN
15
RECI
16
RECV
25
VSSA
32
VSSD
L oudspeaker O utput 1 and 2
Output pins for a 50Ω loudspeaker
Analog input pin for connecting a capacitor for offset cancellation.
Analog input pin for connecting a capacitor for offset cancellation.
Analog input pin for connecting a capacitor for background noise monitoring.
Analog input for the handsfree receive path. Should be connected to RO via coupling
capacitor.
Analog input for receive voice switching path.
Power supply pin for LS1-LS2 output amplifier.
V oltage S ource S ource D igital
26
VDDD
ca
Negative Digital Power Supply
V oltage D rain D rain D igital
Te
ch
ni
Positive Digital Power Supply
Revision 3.4
Page 3 of 19
austriamicrosystems
Data Sheet AS2522B
Te
ch
ni
ca
am
lc s
on A
te G
nt
st
il
lv
al
id
Detailed Block Diagram
Revision 3.4
Page 4 of 19
austriamicrosystems
Data Sheet AS2522B
limits the output voltage at RO to 1V p. It prevents harsh
distortion and acoustic shock. There is LLC for this path.
DC conditions
The gain of the LS → LO1/LO2 receive path is set to
+29dB. This gain can be changed by programming from
+22dB to -37dB in 1dB steps. The user can also change
the gain via Register VOL (See section "Handsfree"). The
receive input is the differential signal of RI and STB. The
soft clip circuit limits the output voltage at LO1 of LO2 to
1V p. It prevents harsh distortion and acoustic shock. There
is optional LLC for this path.
The DC characteristic is determined by the voltage at LIpin and a 30Ω resistor between LI- and LS-pin. It can be
calculated by the following equation: V LS = V LI + I Line *
30Ω. V LI can be programmed to be 3.5V or 4.5V.
2/4 wire conversion
AC-impedance
The AC-impedance of AS2522 is set to t.m. 1000Ω. With
the external capacitor at CI-pin it can be programmed
complex. With an external resistor of approx. 1.5kΩ
connected to the LS-pin it can be programmed to 600Ω.
Side Tone
The line loss compensation is programmable (Register
0x0C). When it is activated, the transmit and receive gains
for both I/O’s are decreased by 6dB at line currents from
20mA to 50mA or from 45mA to 75mA.
am
lc s
on A
te G
nt
st
il
AS2522 has a built-in dual Wheatstone bridge with one
common ground. This provides a maximum of
independence of AC-impedance and side tone from each
other. One can adapt side tone without changing the ACimpedance.
Line Loss Compensation
lv
The normal operating mode is from 15mA to 100mA. An
operating mode with reduced performance is from 5mA to
15mA. In the line hold range from 0mA to 5mA the device
is in a power down mode.
al
id
Functional Description
Handsfree
The handsfree function allows voice communication without
using the handset (full 2-way speaker phone). Two voice
controlled attenuators prevent acoustic coupling between
the loudspeaker and the microphone. The voice switching
circuit has three states, namely idle, transmit or receive. In
receive mode the attenuation of the receive path and the
transmit path can be controlled by Register VOL between
0dB and -20dB. The following table shows how voice
switching is controlled
A good side tone cancellation can be achieved by using the
following equation:
Z BAL /Z LINE = 10
Transmit path
ca
The gain of the M1/M2 → LS is set to +37dB. This gain
can be changed by programming from +30dB to +45dB in
1dB steps (Register Txgain). The input is differential with
ni
an impedance of 10kΩ. The soft clip circuit limits the
output voltage at LS to 2V p. There is LLC for this path.
ch
The gain of the M3/M4 → LS is set to +46dB.
This gain can be changed by programming from +39dB to
+54dB in 1dB steps. The input is differential with an
Te
impedance of 10kΩ. The soft clip circuit limits the output
voltage at LS to 2V p . There is no LLC for this path.
Receive path
The gain of the LS → RO receive path is set to +1dB.
This gain can be changed by programming from -6dB to
+9dB in 1dB steps (Register Rxgain). The receive input is
the differential signal of RI and STB. The soft clip circuit
Revision 3.4
Page 5 of 19
austriamicrosystems
Data Sheet AS2522B
voice switching circuit
TX_atten
Voice
switching
speech
Backgnd
noise
monitor
al
id
RX
Gmax = +9dB
Gmin = -21dB … -40dB (VOL)
LINE
+23dB
+8dB
Offset
comp
Compress
Peak
detector
lv
+14dB
speech
+3dB
Voice
switching
FT2
Peak
detector
am
lc s
on A
te G
nt
st
il
CTXoffset
RO
CBN
RECV
RECI
Compress
Offset
comp
Compress
Peak
detector
Offset
comp
FT1
Cmicoffset
CBckgnd
Gmax = -4dB … +16dB (VOL)
Gmin = -33dB
Rx > Tx_atten
Tx_atten > Rx
Speech
Mode
Rx-gain
Tx-gain
Remark
X
Receive
0db to -20dB
-50dB to -30dB
adjustable with VOL-setting
NO
Idle
-25
-25
middle position
YES
Transmit
-50dB
0dB
independent of VOL-setting
ca
Tx_atten > Rx
IDLE-mode
RX-mode
TX-mode
0dB
ni
ch
Te
Vol max
+12dB
-10dB
TX-gain
-20dB
Vol default
Vol min
-25dB
-30dB
-40dB
RX-gain
-50dB
Revision 3.4
Page 6 of 19
austriamicrosystems
Data Sheet AS2522B
Serial Interface
D7
D6
D5
D4
D3
D2
D1
D0
LLC5
LLC4
LLC3
LLC2
LLC1
LLC0
xPOR
POR
am
lc s
on A
te G
nt
st
il
Power on reset information in Statusbits D1 and D0
lv
The settings of the AS2522 are stored in 16 registers. Each
register has 4 bit data width. Writing data into the AS2522 also
causes the sending of the AS2522 status information on Pin D0.
This information consists of the DC-current information (from the
Line Loss Compensation circuit) and the status of the power-on
reset circuit to test if AS2522 has already powered up.
al
id
Registers
D1
D0
0
0
0
1
AS2522 is in POR state
1
0
AS2522 is active
1
1
DC-current information in Statusbits D7 – D2
000000
000001
000011
000111
001111
LLC-bit HI
<20mA
<45mA
20-26mA
45-51mA
26-32mA
51-57mA
32-38mA
57-63mA
38-44mA
63-69mA
44-50mA
69-75mA
>50mA
>75mA
ni
011111
LLC-bit LO
ca
D[7:2]
Te
ch
111111
Revision 3.4
Page 7 of 19
austriamicrosystems
Data Sheet AS2522B
Timing
The data format for writing to a register has the following form:
xCS
DO
D7
A1
D6
A0
D5
D3
D4
D2
D3
D2
The pins xCS,CLK,DI have internal pull-up resistors.
Parameter
Symbol
MIN
CLK Pulse width HIGH
t6
100ns
CLK Pulse width LOW
t5
100ns
xCS to first falling CLKedge setup time
t1
50ns
CLK to DOUT delay
t2
DIN to CLK setup time
DIN to CLK hold time
D0
MAX
50ns
t4
50ns
t6
t4
ca
t3
TYP
ch
DIN
D1
ni
xCS
CLK
t2
D0
50ns
t3
t5
t1
D1
am
lc s
on A
te G
nt
st
il
Note:
A2
lv
A3
DI
al
id
CLK
Te
DOUT
Revision 3.4
Page 8 of 19
austriamicrosystems
Data Sheet AS2522B
Serial interface Registers
The following table shows the content of the 16 control registers.
For a detailed description of the commands see Application note AN522.
Address
Data
Default value
after reset
Control registers AS2522A, AS2522B
A A A A D D D D
3 2 1 0 3 2 1 0
1 DTMFpair
CT0
x
x
x
x
x
x
V0
x
x
M1
M0
x
Soft-RX
Soft-TX
x
x
x
x
Revision 3.4
Mask
1
0101
Tone:
DTMF-signal path 0...OFF,
1...ON
preemph: DTMF-preempahsis 0...2.2dB, 1…3.2dB
CT1 CT0: @RO
@LO1/LO2
0
0
-36dB -15dB
DTMF-confidence level
0
1
-30dB
-9dB
rel. to pin LS
1
0
-24dB
-3dB
1
1
-18dB
+3dB
Single Tone frequencies if FSK=0 (Addr. 12) and RING/Beep Volum e [4]
frequ1 frequ0
V1
0
0
800Hz
0
0
1
1067Hz
0
1
0
1333Hz
1
1
1
1333Hz
1
Tone Generator m ode, single tone path
V0:
0
1
0
1
0000
RING volume
-17.5dB
-11.5dB
-5.5dB
0dB
0000
ldbr: Digital tone at RO
ldbl: Digital tone at LO1/LO2
MASK: Mask function
DC/DC: DC/DC-converter
x
Bnon
1
Data DTMF-level LOW GROUP at pin LS
0x0
-16dBm
:
:
0xC
-4dBm
DTMF-settings
0000
x
ring
1
1100
RING:
RING-path
0...OFF,
BNON:
Noise monitor
0...OFF,
SOFTRX: Softclip RX
0...OFF,
SOFTTX: Softclip TX
0...OFF,
DC/DC-Converter ON/OFF,Mask
x
ldbr
0
DTMF-Level 13 steps, 1dB stepsize
0000
Burl
0
Frequency
0Hz
800Hz (ring)
1067Hz (ring)
1333Hz (ring)
1300Hz (V.23)
2100Hz (V.23)
1200Hz (Bell 202)
2200Hz (Bell 202)
980Hz (V.21)
1180Hz (V.21)
1070Hz (Bell 103)
1270Hz (Bell 103)
1650Hz (V.21)
1850Hz (V.21)
2025Hz (Bell 103)
2225Hz (Bell 103)
BURS: Analog tone at RO
0...OFF,
1...ON
BURL: Analog tone at LO1/LO2 0...OFF,
1...ON
M1 M0: Tone generator mode select
0 0
Tone generator OFF
0 1
DTMF generator mode
1 0
Single tone Analog mode
1 1
Single tone Digital mode ( RING )
Softclip-settings, Noise m onitoring
Burs
1
ldbl
1
Te
0
Data
f[3:0]
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
ca
CT1
x
preemph
x
HIGH Group
c1 c0 fHigh
0 0 1209Hz
0 1 1336Hz
1 0 1477Hz
1 1 1633Hz
ni
1
x
Single tone mode AS2522B ONLY
AND FSK=1 (Addr 12):
DC/DC
0
0
x
V1
1
0
1
ch
0
1
1
0 DTMFLevel
Tone
0
0
1
frequ0
0
0
frequ1
0
0000
DTMF-Generator mode:
LOW-Group
r1 r0 fLow
0 0 697Hz
0 1 770Hz
1 0 852Hz
1 1 941Hz
al
id
0
lv
0
am
lc s
on A
te G
nt
st
il
0
na
No operation. W rite to this location to get AS2522-Satus
inform ation without altering any other setting.
Frequency select depending on Tone Generator mode
f0, r0
0 Nop
f2, r1
0
f3, c0
0
f4, c1
0
1...ON
1...ON
1...ON
1...ON
0...OFF,
0...OFF,
0...OFF,
0...OFF,
1...ON
1...ON
1...ON
1...ON
Page 9 of 19
austriamicrosystems
Data Sheet AS2522B
Address
Data
Control registers AS2522A, AS2522B
Default value
after reset
A A A A D D D D
3 2 1 0 3 2 1 0
0
0
0
0 16 gains
Handsfree receive endgain
0111
1
Data RXgain TXgain
0x0
-20dB
-30dB
Min. receive volume
:
:
0xF
0dB
-50dB
Max. receive volume
Handsfree switching characteristic
1000
x
x
x
x
off1 off0: BGN-offset
0
0
120mV
0
1
180mV
1
0
240mV
1
1
300mV
1
1
0
0
1
1
1
0
0
x
x
Hfs0
Hfs1
x
x
Speed of voice switching
max speed
min speed
[16], 16 steps, 1dB stepsize
0111
am
lc s
on A
te G
nt
st
il
1
off0
1 16 gains
Data HS-mode HF-mode
0x0
30dB
39dB
:
:
:
0xF
45dB
54dB
Receive gain [16], 16 steps, 1dB stepsize
off1
0 16 gains
Hfs1 HFs0:
0
0
0
1
1
0
1
1
Transmit gain
al
id
1
0
lv
1
Data HS-mode HF-mode
0x0
-6dB
22dB
:
:
:
0xF
+9dB
37dB
FSK-mode, LLC[2], LI-Voltage
0111
0111
AS2522B:
FSK: Frequency select in single tone mode AS2522B ONLY
FSK:
0
Single Tone frequencies are read from Addr. 4: frequ1, frequ0
1
Single Tone frequencies are read from Addr. 1: f4,f3,f2,f1
Llc1
Llc0
x
x
LIV: Voltage at pin LI
0...3.5V, 1...4.5V
LLC1 LLC0: Line loss compensation setting
0
0
20mA-50mA
0
1
NO Line loss compensation
1
0
45-75mA
1
1
NO Line loss compensation
Mute, Lh, Hf, Hook Switch
0000
Mute: Mute transmit
0...OFF,
1...ON
His Hf Lh
0
x x
On Hook
1
0 0
Off Hook, Handset mode
1
1 0
Off Hook, Handfree mode
1
1 1
Off Hook, Loudhearing mode
Krat5,Test3,Test2,Test1: For factory test only !
0000
His
x
x
x
x
x
x
x
ch
Test1
Hf
ni
ca
Liv
x
Test2
0
x
Lh
1
1
Mute
1
0
Krat5
1
1
Test3
1
FSK
AS2522A
FSK: For factory test only !
1
1
1 x
Reset to defaults
na
Te
1
Revision 3.4
Page 10 of 19
austriamicrosystems
Data Sheet AS2522B
Electrical characteristics
Electrical characteristics are measured with the Test Circuit
application. Typical mean values will not be tested.
al
id
Absolute maximum ratings
Positive Supply Voltage
-0.3V <= V DD <= 7V
Input Current
+/- 25mA
Input Voltage (LS)
-0.3V <= V in <= 12V
-0.3V <= V in <= 8V
lv
Input Voltage (LI, CS)
Input Voltage (STB, RI)
-0.3V <= V in <= V DD +0.3V
am
lc s
on A
te G
nt
st
il
Digital Input Voltage
-2V <= V in <= V DD +0.3V
+/- 1000V
Electrostatic Discharge (HBM 1.5kΩ-100pF)
Storage Temperature
-65°C to +125°C
Recommended operating conditions
Supply Voltage (generated internally)
3V <= V DD <= 5V
Operating Temperature
DC characteristics
-25°C to +70°C
ca
I Line =15mA w/o operation of any additional external
circuitry, unless other specified
Parameter
Type
Max
Units
Test
Speech Mode
3
6
mA
Y
Operating Current
Handsfree Mode
7
10
mA
Y
Line Voltage LIVolt=0
Line Voltage LIVolt=1
15mA<=ILINE<=100mA
3.5
4.5
3.8
4.8
V
V
Y
Y
mA
N
I DDS
Operating Current
I DDH
ni
Symbol
ch
V LI
Output Current, Sink
CS,SS
Te
I OL
Revision 3.4
Conditions
VOL=0.4V
Min
3.2
4.2
1
Page 11 of 19
austriamicrosystems
Data Sheet AS2522B
Transmit characteristics
I Line =15mA f=800Hz, default settings unless other specified
Symbol
A M1/2TX
Parameter
Transmit Gain
Conditions
Min
Type
Max
Units
Test
Z AC(syn)= 1000Ω
35
+36.5
38
dB
Y
Z AC(syn) =1000Ω
43
+45.0
47
dB
A M3/4TX
Transmit Gain
M3/M4 → LS
al
id
M1/M2 → LS
Y
∆ A TX
Variation with frequency
f = 500Hz … 3.4kHz
±0.8
dB
A VRM12
Control range
16 steps
-7/+8
dBr
N
16 steps
-7/+8
dBr
N
A VRM34
Control range
am
lc s
on A
te G
nt
st
il
M2/M4 → LS
lv
M1/M2 → LS
THD
Distortion
V AGC1
Soft Clip Level
V LS =0.25VRMS
N
2
%
Y
2
VP
N
2
VP
N
M1/M2 → LS at LS
V AGC2
Soft Clip Level
Soft Clip Overdrive
M1/M2 - M3/M4
20
dB
N
t attack
Attack time
70
us/6dB
N
t decay
Decay time
100
ms/6dB
N
Z IN-M1/2
Input Impedance
M1/M2
10
kΩ
N
Z IN-M3/4
Input Impedance
M3/M4
10
kΩ
N
V INmax
Input Voltage Range
M1/2 - M3/4
differential
±1
Vp
N
V NO
T AMP =25°C
dBmp
Y
Mute Attenuation
Mute activated
dB
Y
ca
A SCO
ni
M3/M4 → LS at LS
ch
Noise Output Voltage
LS
Handset mode
Gain = 36.5dB
60
Te
A MUTE
-72
Revision 3.4
Page 12 of 19
austriamicrosystems
Data Sheet AS2522B
Receive characteristics
I Line =15mA f=800Hz, default settings unless other specified
A RO
Conditions
Receive Gain
Z AC(syn) =1000Ω
LS → RO
Vol default
Min
Type
Max
Units
Test
-2
-0.5
1
dB
Y
+28
+29.0
+31
dB
Receive Gain
Z AC(syn) =1000Ω
LS → LO1/LO2
Vol maximum
∆ A RX
Variation with frequency
f=500Hz to 3.4kHz
±0.8
dB
A VRRO
Control range
16 steps
-7/+8
dBr
N
16 steps
-7/+8
dBr
N
LS → RO
A VRLS
Control range
am
lc s
on A
te G
nt
st
il
LS → LS1/LS2
Y
N
lv
A LO12
Parameter
al
id
Symbol
THD LS
Distortion LS1/LS2
V LS =0.25VRMS
5
%
Y
THD RO
Distortion RO
V LS =0.25VRMS
2
%
Y
V UFC
Unwanted Freq. Cmp.
f = 200 … 20kHz
-60
dBm
Y
1
VP
N
V AGCRO Soft Clip Level
RO
V AGCLS
Soft Clip Level
LS1/2
2
VP
N
A SCLS
Soft Clip Overdrive
LS1/2
10
dB
N
t attack
Attack time
70
us/6dB
N
t decay
Decay time
100
ms/6dB
N
V NO
Noise Output Voltage
RO
dBmp
Y
ca
Gain = 3dB
Input Imp. RI
Input Voltage Range RI
8
±2
kΩ
Vp
N
Input Imp. STB
Input Volt. Range STB
80
±2
kΩ
Vp
N
dB
Y
dB
Y
ch
Z IN-STB
V INmax
-72
ni
Z IN-RI
V INmax
T AMP =25°C
Side tone
V RI <=0.25VRMS
26
RL
∆ Z AC/°C
Return Loss
Temp. Variation
Z AC(syn) =1000Ω
18
Te
ST
Revision 3.4
0.5
Ω/°C
Page 13 of 19
austriamicrosystems
Data Sheet AS2522B
DTMF characteristics
I Line =15mA w/o operation of any additional external circuitry, unless other specified, default settings
Conditions
Tone level low group
at LS
Default
MF range
DTMF level range
low group at LS
13 steps
Prg. in Service mode
∆ V L-H
Preemphasis L-H
Preemphasis=1
UFC
Unwanted frequency
components
300 Hz - 4.3kHz
4.3kHz - 7kHz
7kHz - 10kHz
10kHz - 14kHz
14kHz - 28.5kHz
28.5kHz - 40kHz
∆f
Frequency deviation
V CT-H
Comfort tone handset
Rel to LS
programmable in
service mode
V CT-L
Comfort tone
Loudspeaker
Rel to LS
programmable in
service mode
Ringer
Parameter
ca
Symbol
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
ni
Frequency
Frequency
Frequency
Frequency
Frequency
Frequency
Frequency
Frequency
Frequency
Frequency
Frequency
Frequency
Frequency
Frequency
Frequency
Frequency
Te
ch
F0
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
F14
F15
Revision 3.4
Type
Max
Units
Test
-7
-6
-5
dBm
Y
-18/-6
2.7
dBm
N
3.7
dB
Y
-40
-46
-52
-58
-70
-80
dBm
dBm
dBm
dBm
dBm
dBm
Y
Y
Y
Y
Y
Y
1.2
%
Y
-36
-30
-24
-18
dBr
dBr
dBr
dBr
N
N
N
N
-15
-9
-3
+3
dBr
dBr
dBr
dBr
N
N
N
N
Units
Test
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
N
Y
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
3.2
am
lc s
on A
te G
nt
st
il
V MFlow
Min
al
id
Parameter
lv
Symbol
Conditions
Min
770
1025
1280
Type
0
800
1067
1333
1300
2100
1200
2200
980
1180
1070
1270
1650
1850
2025
2225
Max
830
1110
1385
Page 14 of 19
austriamicrosystems
Data Sheet AS2522B
Miscellaneous
Symbol
Parameter
Conditions
Min
Type
Max
Units
Test
Pacifier level at RO
RL = 150 Ohm
30
mV pp
N
V PALS
Pacifier level at LS1/2
RL = 50 Ohm
100
mV pp
N
Test circuit
al
id
V PARO
15nF
10V
LS
M3
15nF
11
30
10
RI
M4
LI
3
15nF
am
lc s
on A
te G
nt
st
il
600
Iline
5
lv
100uF
10uF
13
M1
300
6
1uF
Vac
15nF
7
BC327
8
6k
14
STB
M2
CS
10uF
RO
17
CI
100nF
RECI
32
9
4
VSSD
VSS
15
16
AS2522A
12
SS
LO2
22
10k
100nF
RECV
BC327
150
10k
23
VPP
OSC
CBN
27
28
29
30
31
20
FT2
10uF
1uF
1
1uF
2
FT1
AGND
VDDD
19
18
VDD
CM
100uF
5V1
xCS
DO
DI
CLK
3.58MHz Resonator
Te
ch
ni
ca
21
24
VSSA
22uF
25
26
470uF
50
LO1
Revision 3.4
Page 15 of 19
austriamicrosystems
Data Sheet AS2522B
Te
ch
ni
ca
am
lc s
on A
te G
nt
st
il
lv
al
id
Typical application
Revision 3.4
Page 16 of 19
austriamicrosystems
Data Sheet AS2522B
am
lc s
on A
te G
nt
st
il
lv
al
id
Bonding Diagram
Te
ch
ni
ca
32 Lead 7x7mm TQFP dimensions
Revision 3.4
Page 17 of 19
austriamicrosystems
Data Sheet AS2522B
Packaging
Ordering Information
Number
Package
Description
AS2522B Q
TQFP
plastic thin quad flat package –
32 leads (suffix T)
Pin-out, Marking
AS2522B F
DOF
Dice-on-Foil
LO1
LO2
VPP
CM
CBN
AGND
VDD
RO
am
lc s
on A
te G
nt
st
il
YYWWAAA
AS2522X
24
23
22
21
20
19
18
17
year of production
calendar week of production
austriamicrosystems AG assembly ID
X
revision
Te
ch
ni
ca
YY
WW
AAA
Revision 3.4
al
id
1
2
3
4
5
6
7
8
VSS 9
LI 10
RI 11
SS 12
LS 13
CI 14
RECI 15
RECV 16
FT1
FT2
M4
M2
M3
M1
STB
CS
Devices sold by austriamicrosystems AG are covered by
the warranty and patent identification provisions appearing
in its Term of Sale. austriamicrosystems AG makes no
warranty, express, statutory, implied, or by description
regarding the information set forth herein or regarding the
freedom of the described devices from patent infringement.
austriamicrosystems AG reserves the right to change
specifications and prices at any time and without notice.
Therefore, prior to designing this product into a system, it
is necessary to check with austriamicrosystems AG for
current information. This product is intended for use in
normal commercial applications. Applications requiring
extended temperature range, unusual environmental
requirements, or high reliability applications, such as
military, medical life-support or life-sustaining equipment
are specifically not recommended without additional
processing by austriamicrosystems AG for each
application.
lv
32
31
30
29
28
27
26
25
VSSD
OSC
CLK
DI
DO
xCS
VDDD
VSSA
32-pin plastic TQFP (suffix Q)
For exact mechanical package dimensions please see
austriamicrosystems AG packaging information.
Copyright
Copyright © 1997-2002, austriamicrosystems AG, Schloss
Premstaetten, 8141 Unterpremstaetten, Austria-Europe.
Trademarks Registered ®. All rights reserved. The material
herein may not be reproduced, adapted, merged,
translated, stored, or used without the prior written consent
of the copyright owner.
The information furnished here by austriamicrosystems AG
is believed to be correct and accurate. However,
austriamicrosystems AG shall not be liable to recipient or
any third party for any damages, including but not limited
to personal injury, property damage, loss of profits, loss of
use, interruption of business or indirect, special, incidental
or consequential damages, of any kind, in connection with
or arising out of the furnishing, performance or use of the
technical data herein. No obligation or liability to recipient
or any third party shall arise or flow out of
austriamicrosystems AG rendering of technical or other
services.
Page 18 of 19
austriamicrosystems
Data Sheet AS2522B
Contact
Headquarters
al
id
austriamicrosystems AG
Communications Business Unit
A 8141 Schloss Premstätten, Austria
T. +43 (0) 3136 500 0
F. +43 (0) 3136 525 01
www.austriamicrosystems.com
USA (east)
Germany
austriamicrosystems USA, Inc.
Suite 400, 8601 Six Forks Road
Raleigh, NC 27615, USA
Phone: +1/919/676 5292
Fax: +1/919/676 5305
am
lc s
on A
te G
nt
st
il
austriamicrosystems Germany GmbH
Tegernseer Landstrasse 85
D-81539 München, Germany
Phone: +49/89/693643-0
Fax: +49/89/693643-66
lv
Sales Offices
United Kingdom
France
austriamicrosystems France S.a.r.l.
124, Avenue de Paris
F-94300 Vincennes, France
Phone: +33/1/43 74 00 90
Fax: +33/1/43 74 20 98
austriamicrosystems UK, Ltd.
Coliseum Business Centre, Watchmoor Park
Camberley, Surrey, GU15 3YL, UK
Phone: +44/1276/23 3 99
Fax: +44/1276/29 3 53
Japan
Italy
Switzerland
ca
austriamicrosystems Italy S.r.l.
Via Leone Tolstoi, 64
I-20146 Milano, Italy
Phone: +39/0242/36713
Fax: +39/0242/290889
austriamicrosystems AG
Shin Yokohama Daini, Center Bldg. 10F
3-19-5, Shin Yokohama
Kohoku-ku, Yokohama 222-0033, Japan
Phone: +81/45/474 0962
Fax: +81/45/472 9845
Distributors & Representatives
USA (west)
Spain, Israel, Korea, Hong-Kong, Taiwan, Malaysia,
Singapore, India, Brazil
Te
ch
ni
austriamicrosystems Switzerland AG
Rietstrasse 4
CH-8640 Rapperswil, Switzerland
Phone: +41/55/220 9000
Fax: +41/55/220 9001
austriamicrosystems USA, Inc.
Suite 116, 4030 Moorpark Ave,
San Jose, CA 95117, USA
Phone: +1/408/345 1790
Fax: +1/408/345 1795
Revision 3.4
austriamicrosystems AG is represented by distributors in
the following countries. Please contact your nearest
regional sales office for the distributor address:
Application Support
Please contact your local sales office or your distributor.
Page 19 of 19