LTC1045 Programmable Micropower Hex Translator/ Receiver/Driver U FEATURES ■ ■ ■ ■ ■ ■ ■ ■ DESCRIPTIO Efficiently Translate Voltage Levels Internal Hysteresis for Noise Immunity Output Latches Included Three-State Outputs Programmable Power/Speed Power Can Be Completely Shut Off ±50V on Inputs with External 100k Limit Resistor 1.2µs Response at 100µA Supply Current U APPLICATIO S ■ ■ ■ ■ TTL/CMOS to ±5V Analog Switch Drive TTL to CMOS (3V to 15V VCC) ECL to CMOS (3V to 15V VCC) Ground Isolation Buffer Low Power RS232 Line Receiver The ISET pin has several functions. When taken to V + the outputs are latched and power is completely shut off. Power/speed can be programmed by connecting ISET to V – through an external resistor. , LTC and LT are registered trademarks of Linear Technology Corporation. LTCMOS is a trademark of Linear Technology Corporation. U ■ The LTC®1045 is a hex level translator manufactured using Linear Technology’s enhanced LTCMOSTM silicon gate process. It consists of six high speed comparators with output latches and three-state capability. Each comparator’s plus input is brought out separately. The minus inputs of comparators 1 to 4 are tied to VTRIP1 while 5 and 6 are tied to VTRIP2. TYPICAL APPLICATIO 5V Flat Ribbon Cable Driver/Receiver 5V 20 TTL IN XMT IN V+ + 1 VOH 20 VOL 1.4V – ISET V– DIS 13 XMT OUT 66-FT FLAT RIBBON CABLE RCV IN V+ + 1 VOH ZO = 150Ω 11 150Ω ADJACENT CONDUCTORS VOL 12 10 0.5V – ISET V– 10 DIS 13 RCV OUT TTL OUT 11 12 1045 TA01 XMT IN (5V/DIV) XMT OUT (1V/DIV) RCV IN (1V/DIV) RCV OUT (5V/DIV) 100ns/DIV 045 TA01a 1045fc 1 LTC1045 W U PACKAGE/ORDER INFORMATION W W U W (Notes 1, 2) Total Supply Voltage (V +, V TOP VIEW to V –, V .............. 18V Output High Voltage (VOH) ...................................... ≤ V + Input Voltage ....................................18V to (V – – 0.3V) Output Short-Circuit Duration (VOH – VOL ≤ 10V) ................................... Continuous ESD (MIL-STD-883, Method 3015) .................... 2000V Operating Temperature Range ................. –40°C to 85°C Storage Temperature Range ................. – 55°C to 150°C Lead Temperature (Soldering, 10 sec).................. 300°C OH U ABSOLUTE MAXIMUM RATINGS OL) ORDER PART NUMBER VOH 1 20 V + IN1 2 19 OUT1 IN2 3 18 OUT2 IN3 4 17 OUT3 IN4 5 16 OUT4 IN5 6 15 OUT5 IN6 7 14 OUT6 VTRIP2 8 13 DISABLE VTRIP1 9 12 ISET V – 10 11 VOL LTC1045CN LTC1045CSW N PACKAGE SW PACKAGE 20-LEAD PDIP 20-LEAD SO WIDE TJMAX = 110°C, θJA = 90°C/ W (N) TJMAX = 110°C, θJA = 90°C/ W (SW) J PACKAGE 20-LEAD CERDIP TJMAX = 150°C, θJA = 70°C/ W (J) LTC1045CJ OBSOLETE PACKAGE Consider N Package for Alternate Source Consult LTC Marketing for parts specified with wider operating temperature ranges. ELECTRICAL CHARACTERISTICS The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. V + = VOH = 5V, V – = VOL = 0Vunless otherwise specified. (Note 3) . SYMBOL PARAMETER IB Input Bias Current CONDITIONS V – ≤ VIN ≤ V + MIN TYP ±1 ● IS Trip Voltage Range (Pins 8, 9) V + to V – Supply Current ● V– DISABLE = V +, RSET = 10k 2.5 ● IOFF V + to V – Supply Current in Shutdown DISABLE = ISET = V + Voltage on ISET (Pin 12) RSET = 10k VOH VOL ISINK TTL Output High Voltage TTL Output Low Voltage Output Short-Circuit Sink Current IOUT = – 360µA, V + = 4.5V IOUT = 1.6mA, V + = 4.5V VIN = VTRIP – 100mV, VOUT = V + ISOURCE Output Short-Circuit Source Current VIN = VTRIP + 100mV, VOUT = V – 1 0.9 ● ● ● Three-State Leakage Current 0.6 2.4 ● ● IOZ 7.5 5.5 4.0 3.2 DISABLE = V +, VOL ≤ VOUT ≤ VOH 1.25 4.4 0.2 15 Output Resistance to VOH IOUT ≤ 100µA ROL Output Resistance to VOL IOUT ≤ 100µA 0.005 260 ● 100 ● ISET Voltage for Shutdown DISABLE Input Logic Levels V + = 4.5V, V – = 0V V + = 5.5V, V – = 0V VIH VIL Input Supply Differential (V + – V –) (Note 3) Output Supply Differential (VOH – VOL) (Note 3) 0.4 8.0 ● ROH 0.5 V+ – 2 3.5 4.5 10 ● VREF MAX ● V + – 0.5 ● ● 2.0 ● ● 1 475 600 180 250 UNITS nA µA V mA mA nA µA V V V V mA mA mA mA µA µA Ω Ω Ω Ω V 4.5 0.8 15 V V V 3 15 V 1045fc 2 LTC1045 AC ELECTRICAL CHARACTERISTICS The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. V + = VOH = 5V, V – = VOL = 0V, unless otherwise specified. SYMBOL PARAMETER CONDITIONS td Test Circuit Figure 1 RSET = 10k, ±100mV Drive Test Circuit Figure 2 Response Time tSETUP tHOLD tACC tIH, tOH Time Before Rising Edge of ISET that Data Must Be Present Time After Rising Edge of ISET that Data Must Be Present Falling Edge of DISABLE to Logic Level (from Hi-Z State) Rising Edge of DISABLE to Hi-Z State MIN MAX UNITS 250 350 80 ns ns ns Test Circuit Figure 2 0 ns Test Circuit Figure 3 165 ns Test Circuit Figure 3 200 ns Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Note 2: The maximum differential voltage between any two power pins (V +, V –, VOH and VOL) must not exceed 18V. The maximum recommended operating differential is 15V. TYP ● Note 3: During operation near the maximum supply voltage limit, care should be taken to avoid or suppress power supply turn-on and turn-off transients, power supply ripple or ground noise; any of these conditions must not cause a supply differential to exceed the absolute maximum rating. U W TYPICAL PERFORMANCE CHARACTERISTICS I + vs RSET I + vs Temperature 5 Delay Time vs RSET 1.2 5 V + = 5V 3 RSET = 0 2 RSET = 10k 1.0 DELAY TIME (µs) V + TO V – CURRENT (mA) 4 3 2 1 1 TA = 25°C V + = VOH = 5V V – = VOL = 0V VIN = VTRIP ±100mV 0.8 0.6 0.4 0.2 RSET = 1M –25 75 0 25 50 TEMPERATURE (°C) 100 125 0 100 1k 10k RSET (Ω) 100k 0 100 1M 1k 10k RSET (Ω) 100k 1M 1045 G03 1045 G02 1045 G01 Hysteresis vs RSET VREF vs Temperature 2.5 20 V + = 5V 2.0 RSET = 1M 1.5 RSET = 10k 1.0 V + = 5V 18 COMPARATOR HYSTERESIS (mV) 0 –50 VOLTAGE ON ISET PIN (V) V + TO V – CURRENT (mA) 4 TA = 25°C V + = VOH = 5V V – = VOL = 0V 0.5 16 14 12 10 8 6 4 2 0.1 –50 –25 75 0 25 50 TEMPERATURE (°C) 100 125 1045 G04 0 100 1k 10k RSET (Ω) 100k 1M 1045 G05 1045fc 3 LTC1045 U U U PIN FUNCTIONS VOH (Pin 1): High Level to which the Output Switches. VOL (Pin 11): Low Level to which the Output Switches. IN1 to IN7 (Pins 2 to 7): Six Comparator Inputs; Voltage Range = V – to V – + 18V. ISET (Pin 12): This has three functions: 1) RSET from this pin to V – sets bias current, 2) when forced to V + power is shut off completely and 3) when forced to V + outputs are latched. VTRIP2 (Pin 8): Trip Point for Last Two Comparators (Inputs 5,6); Voltage Range = V – to V + – 2V. VTRIP1 (Pin 9): Trip Point for First Four Comparators (Inputs 1 to 4); Voltage Range = V – to V + – 2V. DISABLE (Pin 13): When high, outputs are Hi-Z. OUT6 to OUT1 (Pins 14 to 19): Six Driver Outputs. V + (Pin 20): Comparator Positive Supply. V – (Pin 10): Comparator Negative Supply. TEST CIRCUITS 5V t r ≤ 10ns V+ + VIN 5V VOH – VTRIP = 1.2V t IH OUTPUT VOL V– V+ 50pF 5V 90% DISABLE + 50% 0V 10% t IH OUTPUT – tr 1.3V 1.1V 90% DISABLE 90% 5V VOL t r = t f ≤ 10ns 90% –5V 1045 F03a 10% 10% t r ≤ 10ns td td t OH 5V 2.5V OUTPUT 10k OUTPUTS 1.2V VIN 10pF tf 90% VOH DISABLE 50% 10k 0V 1045 F01 Figure 1. Response Time Test Circuit 10% t OH OUTPUT V + 10pF 5V OUTPUTS DISABLE VIN + VTRIP = 1.2V – 10% –5V 1045 F03b t r ≤ 10ns 90% t ACC 100mV DISABLE 50% 10% VTRIP VIN tACC OUTPUT –100mV t HOLD t SETUP 50pF 5V 5V OUTPUTS DISABLE ISET 50% –5V 1045 F03c 0V Figure 3. Three-State Output Test Circuit Conditions: V + = VOH = 5V, V – = VOL = 0V 5V ISET 50% 0V 1045 F02 Figure 2. Latch Test Circuit 1045fc 4 LTC1045 W BLOCK DIAGRAM V OH V+ 20 1 V+ V OH + IN1 2 LEVEL SHIFT 19 OUT1 LATCH – DIS V BIAS V– LE VOL V+ V OH + IN2 3 18 OUT2 – DIS VBIAS LE V– V OL V+ V OH + IN3 4 17 OUT3 – DIS VBIAS LE V– V OL V+ V OH + IN4 5 16 OUT4 – DIS VBIAS LE V– V OL V+ V OH + IN5 6 15 OUT5 – DIS VBIAS LE V– V OL V+ V OH + IN6 7 14 OUT6 – DIS VBIAS LE V– V OL 13 DISABLE VREF ≈ 1.6V VTRIP1 9 VBIAS BIAS GENERATOR ∼8k LATCH ENABLE SHUTDOWN 8 VTRIP2 10 V– RSET 12 ISET 11 VOL 1045 BD 1045fc 5 LTC1045 U U W U APPLICATIONS INFORMATION The LTC1045 consists of six voltage translators and associated control circuitry (see Block Diagram). Each translator has a linear comparator input stage with the positive input brought out separately. The negative inputs of the first four comparators are tied in common to VTRIP1 and the negative inputs of the last two comparators are tied in common to VTRIP2. With these inputs the switching point of the comparators can be set anywhere within the common mode range of V – to V + – 2V. To improve noise immunity each comparator has a small built-in hysteresis. Hysteresis varies with bias current from 7mV at low bias current to 20mV at high bias current (see typical curve of Hysteresis vs RSET). is turned off to the linear circuitry, the CMOS output logic is powered and maintains the output state. With no DC load on the output, power dissipation, for all practical purposes, is zero. Latching the output is fast—typically 80ns from the rising edge of ISET. Going from the latched to flow-through state is much slower—typically 1.5µs from the falling edge of ISET. This time is set by the comparator’s power-up time. During the power-up time, the output can assume false states. To avoid problems, the output should not be considered valid until 2µs to 5µs after the falling edge of ISET. Putting the Outputs in Hi-Z State Setting the Bias Current Unlike CMOS logic, any linear CMOS circuit must draw some quiescent current. The bias generator (Block Diagram) allows the quiescent current of the comparators to be varied. Bias current is programmed with an external resistor (see typical curve of I + vs RSET). As the bias current is decreased, the LTC1045 slows down (see typical curve of Delay Time vs RSET). Shutting Power Off and Latching the Outputs In addition to setting the bias current, the ISET pin shuts power completely off and latches the translator outputs. To do this, the ISET pin must be forced to V + – 0.5V. As shown in Figure 4, a CMOS gate or a TTL gate with a resistor pull-up does this quite nicely. Even though power V+ 4.5V TO 15V A DISABLE input sets the six outputs to a high impedance state. This allows the LTC1045 to be interfaced to a data bus. When DISABLE = “1” the outputs are high impedance and when DISABLE = “0” they are active. With TTL supplies, V + = 4.5V to 5.5V and V – = GND, the DISABLE input is TTL compatible. Power Supplies There are four power supplies on the LTC1045: V +, V –, VOH and VOL. They can be connected almost arbitrarily, but there are a few restrictions. A minimum differential must exist between V + and V – and VOH and VOL. The V + to V – differential must be at least 4.5V and the VOH to VOL differential must be at least 3V. Another restriction is caused by the internal parasitic diode D1 (see Figure 5). V+ 20 4.5V TO 5.5V 20 D1 V+ DISABLE LTC1045 DATA 12 10 P1 100k LTC1045 V+ VOH 12 VOL OUTPUT PIN V+ 10 N1 DISABLE 1045 F05 VOL (A) CMOS (B) TTL Figure 4. Driving the ISET Pin with Logic VOL 1045 F04 Figure 5. Output Driver 1045fc 6 LTC1045 U W U U APPLICATIONS INFORMATION Because of this diode, VOH must not be greater than V +. Lastly, the maximum voltage between any two power supply pins must not exceed 15V operating or 18V absolute maximum. For example, if V + = 5V, V – or VOL should be no more negative than – 10V. Note that VOL should not be more negative than – 10V even if the VOH to VOL differential does not exceed the 15V maximum. In this case the V + to VOL differential sets the limit. Input Voltage Output Drive Output drive characteristics of the LTC1045 will vary with the power supply voltages that are chosen. Output impedance is affected by V +, VOH and VOL. V – has no effect on output impedance. Guaranteed drive characteristics are specified in the table of electrical characteristics for V + = VOH = 5V and V – = VOL = 0V. Figures 6 and 7 show relative output impedance for other supply combinations. In general, output impedance is minimized if V + to VOH is minimized and VOH to VOL is maximized. 4 2 VOH – VOL = 3V ROL/[ROL AT (VOH – VOL) = 5V] ROH /[ROH AT (VOH – VOL) = 5V AND (V + – VOH) = 0V] The LTC1045 has no upper clamp diodes as do conventional CMOS circuits. This allows the inputs to exceed the V + supply. The inputs will break down approximately 30V above the V – supply. If the input current is limited with 100kΩ, the input voltage can be driven to at least ±50V with no adverse effects for any combination of allowed power supply voltages. Output levels will be correct even under these conditions (i.e., if the input voltage is above the trip point, the output will be high and if it is below, the output will be low). 3 VOH – VOL = 4V 2 VOH – VOL = 5V 1 SPECIFIED POINT SPECIFIED POINT 1 VOH – VOL = 10V 0 0 2 4 8 6 10 V + – VOH (V) 12 14 16 1045 F06 Figure 6. Relative Output Sourcing Resistance (ROH) vs V + – VOH 0 0 2 4 8 6 10 VOH – VOL (V) 12 14 16 1045 F07 Figure 7. Relative Output Sinking Resistance (ROL) vs VOH – VOL 1045fc 7 LTC1045 U TYPICAL APPLICATIONS ECL to CMOS/TTL Logic 5V V+ ECL IN V OH THREESTATE BUFFER + IN COMP LATCH OUT – VTRIP V– ISET VOL CMOS/TTL (VCC = 5V) DIS 1045 TA02 30k ~ –1.3V 10k –5.2V TTL/CMOS (VCC = 5V) to High Voltage CMOS (VCC = 15V) 15V V+ TTL/CMOS (VCC = 5V) V OH THREESTATE BUFFER + IN COMP VTRIP LATCH OUT – V– ISET VOL CMOS (VCC = 15V) DIS ~1.4V 1045 TA03 20k High Voltage CMOS (VCC = 15V) to TTL/CMOS (VCC = 5V) 5V V+ V OH 10k CMOS (VCC = 15V) IN THREESTATE BUFFER + COMP VTRIP ~2.5V 10k LATCH OUT – V– ISET VOL TTL/CMOS (VCC = 5V) DIS 1045 TA04 1045fc 8 LTC1045 U TYPICAL APPLICATIONS TTL/CMOS (VCC = 5V) to Low Voltage CMOS (VCC = 3V) TTL/CMOS (VCC = 5V) IN 5V 3V V+ V OH THREESTATE BUFFER + COMP VTRIP LATCH OUT – V– ISET VOL CMOS (VCC = 3V) DIS ~1.5V 1045 TA05 100k TTL/CMOS Logic Levels to ±5V Analog Switch Driver 5V V+ TTL/CMOS (VCC = 5V) IN + VTRIP – V OH VDD THREESTATE BUFFER COMP LATCH ±5V IN SW ±5V OUT OUT VSS V– ISET VOL CMOS ANALOG SWITCH (CD4016 FOR EXAMPLE) DIS ~1.4V 1045 TA06 20k –5V TTL/CMOS (VCC = 5V) to 10V/– 5V Clock Driver 10V V+ TTL/CMOS (VCC = 5V) IN THREESTATE BUFFER + COMP VTRIP V OH LATCH OUT 10V TO –5V CLOCK DRIVER – V– ISET VOL ~1.4V 20k DIS 1045 TA07 –5V 1045fc 9 LTC1045 U TYPICAL APPLICATIONS Logic Ground Isolation when Two Grounds are within LTC1045 Common Mode Range SYSTEM A SYSTEM B VCC B = 5V VCC A = 5V V+ TTL/CMOS LOGIC IN V OH THREESTATE BUFFER + 2.7k COMP VTRIP VTRIP = 1.35V LATCH OUT LOGIC OUT – 1k SETS LOGIC THRESHOLD REFERRED TO GND A GND A V– ISET VOL DIS GND B V – = –5V 1045 TA08 (GND B – V – + VTRIP) ≤ GND A ≤ (GND B + VCC B – 2V – VTRIP) Coax Cable Driver/Receiver 5V 5V 20 TTL IN XMT IN V+ + 1 VOH VOL 1.4V – V ISET – DIS 13 XMT OUT 20 30-FT RG 174 COAX CABLE 11 RCV IN V+ + 1 VOH 50Ω VOL 12 10 0.2V – ISET V– DIS 13 11 RCV OUT TTL OUT 50pF 12 10 1045 TA10 RCV OUT (5V/DIV) RCV IN (1V/DIV) XMT OUT (1V/DIV) XMT IN (5V/DIV) 200ns/DIV 1045 TA10a 1045fc 10 LTC1045 U TYPICAL APPLICATIONS ±5V Analog Switch Driver 5V 5V 1 VOH 2 IN1 LTC1045 + V+ 14 20 CD4016 1 SW A 2 ±5V 13 OUT1 19 – 3 3 IN2 + SW B 4 ±5V 9 ±5V 11 ±5V 5 OUT2 18 – 8 4 IN3 TTL OR CMOS LOGIC INPUTS + SW C 6 OUT3 17 – 10 5 IN4 + SW D 12 OUT4 16 – 7 6 IN5 + 1045 TA09 OUT5 15 – 7 IN6 + –5V OUT6 14 – 8 VTRIP2 9 VTRIP1 10 V– DIS ISET VOL 13 12 11 ~1.5V 100k –5V 1045fc 11 LTC1045 U TYPICAL APPLICATIONS Logic Systems DC Isolation SYSTEM A SYSTEM B SYSTEM B POWER SUPPLY 1 VOH 2 IN1 LTC1045 + V+ 20 OUT1 19 – 3 IN2 + OUT2 18 – 4 IN3 + OUT3 17 – TTL OR CMOS 5 IN4 + CMOS OR TTL OUT4 16 – 6 IN5 + OUT5 15 – 7 IN6 + OUT6 14 – SYSTEM A POWER SUPPLY VTRIP* 8 VTRIP2 DIS 13 THREE-STATE CONTROL 1µF 9 VTRIP1 ISET 12 1µF** 10 V– VOL 11 † 100k SYSTEM A GND * SET VTRIP TO HALF WAY BETWEEN VOH AND VOL OF SYSTEM A ** SHUNTS COMMON MODE SIGNAL † PROVIDES LEAKAGE PATH FOR TOTALLY ISOLATED SYSTEMS SYSTEM B GND 1045 TA11 1045fc 12 LTC1045 U TYPICAL APPLICATIONS 24V Relay Supply from 12V/15V Supply V+ 1 VOH V+ LTC1045 2 IN1 + 20 OUT1 19 – 3 IN2 + OUT2 18 – 4 IN3 + OUT3 17 – 5 IN4 V+ + OUT4 16 – 6 IN5 1N4148 + 1N4148 OUT5 15 – V+ 10k 7 IN6 24V + 1µF + 10µF RL ≥ 1k OUT6 14 – 10k 10k 8 VTRIP2 9 VTRIP1 10 13 DIS 12 ISET V– 11 VOL 100k 10k 1045 TA13 1000pF RS232 Receiver 5V 20 30V 100k 2 V+ + –30V 9 0.9V 1 VOH VOL LTC1045 DIS 11 ISET 13 V– 12 10 19 TTL OUT – 10k NOTE: INPUTS HAVE NO INTERNAL PULL-DOWN 1045 TA12 1045fc 13 LTC1045 U TYPICAL APPLICATIONS LED Driver V+ 5V TO 15V 1 VOH V+ LTC1045 2 IN1 + 20 OUT1 19 – 3 IN2 + OUT2 18 – 4 IN3 + OUT3 17 – LOW TURNS LED ON 5 IN4 + OUT4 16 TO LEDs – 6 IN5 + OUT5 15 – 7 IN6 + OUT6 14 – 8 VTRIP2 DIS 9 VTRIP1 10 ISET V– VOL 13 12 11 ≈ 1.5V 100k V+ 5V REF LED 6 – 5 + 100Ω 3 + 1 358 2 8 7 358 2N2905 (USE HEAT SINK) 4 2N2222 – ≈ 1.5V REGULATES LED CURRENT R (ADJUSTS LED CURRENT) 1045 TA14 1045fc 14 LTC1045 U TYPICAL APPLICATIONS Multiwindow Comparator and Display V+ 5V 1 V OH 2 IN1 VREF LTC1045 + 20 V+ OUT1 19 – R VH 3 IN2 + VIN > VREF OUT2 18 – 10k 4 IN3 + OUT3 17 – 10k 5 IN4 + OUT4 16 – 10k 6 IN5 + OUT5 15 – 10k 7 IN6 + OUT6 14 GI MV 57164* BAR GRAPH DISPLAY – 8 VTRIP2 DIS 9 VTRIP1 ISET VIN 10 1 V– VOH 10k 2 IN1 VOL LTC1045 + V+ 13 12 11 20 OUT1 19 – 10k 3 IN2 + OUT2 18 – 10k 4 IN3 + OUT3 17 – 10k 5 IN4 + OUT4 16 – 10k 6 IN5 + OUT5 15 – 10k 7 IN6 + OUT6 14 – VL 8 VTRIP2 9 VTRIP1 10 V– 5V V– DIS ISET VOL VIN < VL 13 * FOR LED CURRENT CONTROL SEE LTC1045 LED DRIVER 12 11 VIN ≤ V + – 2 100(VREF – VH) R= (VH – VL) EACH WINDOW BETWEEN VH AND VL EQUALS 1/10(VH – VL) (VH – VL) ≥ 0.5V 1045 TA15 1045fc 15 LTC1045 U TYPICAL APPLICATIONS ECL to CMOS from Single 5V Supply 5V 1 VOH 2 IN1 ECL IN LTC1045 + V+ 20 OUT1 19 – 3 IN2 ECL IN + OUT2 18 – 4 IN3 ECL IN + OUT3 17 – 5 IN4 ECL IN + OUT4 16 – 10k 6 IN5 5V CMOS OUT CMOS OUT CMOS OUT CMOS OUT 1µF + 1N4148 OUT5 15 – 10k 10k 7 IN6 + 1N4148 OUT6 14 + 10µF – 8 VTRIP2 DIS 9 VTRIP1 10 ISET V– VOL 13 12 11 22k ≈ –3.3V 51k ≈ –1.29V 10k 0.01µF 33k 1000pF NEGATIVE SUPPLY GENERATOR 1045 TA16 1045fc 16 LTC1045 U PACKAGE DESCRIPTION J Package 20-Lead CERDIP (Narrow .300 Inch, Hermetic) (Reference LTC DWG # 05-08-1110) 1.060 (26.924) MAX CORNER LEADS OPTION (4 PLCS) 0.023 – 0.045 (0.584 – 1.143) HALF LEAD OPTION 20 19 18 17 16 15 14 13 12 11 1 2 3 4 5 6 7 8 9 10 0.220 – 0.310 0.025 (5.588 – 7.874) (0.635) RAD TYP 0.045 – 0.068 (1.143 – 1.727) FULL LEAD OPTION 0.005 (0.127) MIN 0.300 BSC (0.762 BSC) 0.200 (5.080) MAX 0.015 – 0.060 (0.381 – 1.524) 0.008 – 0.018 (0.203 – 0.457) 0° – 15° NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE OR TIN PLATE LEADS 0.125 (3.175) MIN 0.045 – 0.065 (1.143 – 1.651) 0.014 – 0.026 (0.356 – 0.660) 0.100 (2.54) BSC J20 1298 OBSOLETE PACKAGE 1045fc 17 LTC1045 U PACKAGE DESCRIPTION N Package 20-Lead PDIP (Narrow .300 Inch) (Reference LTC DWG # 05-08-1510) 1.040* (26.416) MAX 20 19 18 17 16 15 14 13 12 11 1 2 3 4 5 6 7 8 9 10 0.255 ± 0.015* (6.477 ± 0.381) 0.130 ± 0.005 (3.302 ± 0.127) 0.300 – 0.325 (7.620 – 8.255) 0.009 – 0.015 (0.229 – 0.381) ( +0.035 0.325 –0.015 +0.889 8.255 –0.381 ) 0.045 – 0.065 (1.143 – 1.651) 0.020 (0.508) MIN 0.065 (1.651) TYP 0.125 (3.175) MIN 0.005 (0.127) MIN *THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm) 0.100 (2.54) BSC 0.018 ± 0.003 (0.457 ± 0.076) N20 1098 1045fc 18 LTC1045 U PACKAGE DESCRIPTION SW Package 20-Lead Plastic Small Outline (Wide .300 Inch) (Reference LTC DWG # 05-08-1620) 0.496 – 0.512* (12.598 – 13.005) 20 19 18 17 16 15 14 13 12 11 0.394 – 0.419 (10.007 – 10.643) NOTE 1 0.291 – 0.299** (7.391 – 7.595) 0.010 – 0.029 × 45° (0.254 – 0.737) 1 2 3 4 5 6 7 8 9 0.093 – 0.104 (2.362 – 2.642) 10 0.037 – 0.045 (0.940 – 1.143) 0° – 8° TYP 0.009 – 0.013 (0.229 – 0.330) NOTE 1 0.016 – 0.050 (0.406 – 1.270) 0.050 (1.270) BSC 0.014 – 0.019 (0.356 – 0.482) TYP 0.004 – 0.012 (0.102 – 0.305) S20 (WIDE) 1098 NOTE: 1. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS. THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS *DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE **DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE 1045fc Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 19 LTC1045 U TYPICAL APPLICATION Power MOSFET Driver Low Power Consumption Stepper Motor Driver +VM 1 ∅1 VOH LTC1045 2 IN1 + V+ B 20 OUT1 19 – ∅1 TTL STEPPER MOTOR PHASE SIGNALS 3 IN2 + RH BUZ171 ** 4-PHASE BIFILAR STEPPER MOTOR OUT2 18 – ∅2 4 IN3 + OUT3 17 – ∅2 5 IN4 + * OUT4 16 * – 5V 6 IN5 + 51k ≈ 1.4V – 7 IN6 + 20k STEP A CLOCK BUZ71A BUZ71A ** OUT5 15 ** BUZ71A ** BUZ71A ** OUT6 14 – C 8 VTRIP2 DIS 13 MOTOR GND 9 VTRIP1 RP 0.1µF ISET 12 A 10 V– VOL 11 ≈ 0.2V B tON tHOLD 1k FULL STEP DRIVER (5V ≤ VM ≤ 15V) t ON ≈ 3RPC RpC = L/R L IS WINDING INDUCTANCE R = RWINDING + RDS(ON)P + RDS(ON)N IHOLD ≈ VM /RH *VARISTOR GE V24ZA50 **FOR VM ≥ 10V ADD 470Ω IN SERIES WITH LTC1045 OUTPUTS 1045 TA17 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT1016 Ultrafast Precision Comparator 10ns Propagation Delay LT1039 Triple RS232 Driver/Receiver with Shutdown ±12V Supply, No Supply Current in Shutdown LTC1440/LTC1441/LTC1442 Ultralow Power, Single/Dual Comparator with Reference 2.8µA Supply Current 1045fc 20 Linear Technology Corporation LT/LCG 1101 REV C 1.5K • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com LINEAR TECHNOLOGY CORPORATION 1988