TC57 DATA SHEET (02/05/2013) DOWNLOAD

TC57
Line Regulator Controller
Features
General Description
• Low Dropout Voltage: 100mV @ 650mA with
FZT749 PNP Transistor
• 2.7V to 8V Supply Range
• Low Operating Current: 50A Operating,
0.2A Shutdown
• Low True Chip Enable
• Output Accuracy < ±2%
• Small Package: 5-Pin SOT-23A
The TC57 is a low dropout regulator controller that
operates with an external PNP pass transistor, allowing
the user to tailor the LDO characteristics to suit the
application at hand. This results in lower dropout
operation (and often lower cost) compared with
traditional linear regulators with on-board pass
transistors. The maximum output current of a TC57based regulator circuit is limited only by the
characteristics of the external pass transistor. For
example, a maximum output current of 650mA (with a
dropout voltage of 100mV) results when an FZT749
pass transistor is used, while a Darlington configuration
can deliver up to 4A.
Applications
•
•
•
•
•
Battery Operated Systems
Portable Instruments
High-Efficiency Linear Regulator
Post-Regulator for SMPS
Power Supply or Battery Back-Up Supply for
Memory
Flexibility, and superior performance make this family
of regulator controllers the ideal choice in applications
where low dropout voltage and low installed cost are
key.
Functional Block Diagram
Device Selection Table
FZT749
Q1
VIN +3.3V
Output
Part Number
Voltage
TC572502ECT
2.5V
Package
Temperature
Range
5-Pin SOT-23A -40°C to +85°C
TC573002ECT
3.0V
5-Pin SOT-23A -40°C to +85°C
TC573302ECT
3.3V
5-Pin SOT-23A -40°C to +85°C
RBE
47K
CIN
10μF
(Tantalum)
2
RB
1K
4
EXT
VOUT
3
CL
10μF
(Tantalum)
RL
VIN
TC573002ECT
OFF
Other output voltages and package options are available.
Please contact Microchip Technology Inc. for details.
VOUT +3V
ON
5
SHDN
GND
1
Package Type
3.3V Line Input, 3.0V, 500mA Output LDO
5-Pin SOT-23A
SHDN
EXT
5
4
TC57
1
2
3
GND
VIN
VOUT
NOTE: 5-Pin SOT-23A is equivalent to the EIAJ SC-74A.
 2001-2012 Microchip Technology Inc.
DS21437C-page 1
TC57
1.0
ELECTRICAL
CHARACTERISTICS
*Stresses above those listed under "Absolute Maximum
Ratings" may cause permanent damage to the device. These
are stress ratings only and functional operation of the device
at these or any other conditions above those indicated in the
operation sections of the specifications is not implied.
Exposure to Absolute Maximum Rating conditions for
extended periods may affect device reliability.
Absolute Maximum Ratings*
Input Voltage ........................................................+12V
Output Current ....................................................50mA
Output Voltage............................. -0.3V to (VIN + 0.3V)
Power Dissipation.............................................150mW
Operating Temperature Range.............-40°C to +85°C
Storage Temperature Range ..............-40°C to +150°C
TC55 ELECTRICAL SPECIFICATIONS
TC57EP3002 Electrical Characteristics: SHDN = GND, VIN = VOUT + 1V, VOUT = 3V to 5V, IOUT = 0, TA = 25°C, Test Circuit of
Figure 3-1, unless otherwise noted. (Note 2)
Symbol
Parameter
Min
Typ
Max
Units
VIN
Input Voltage
—
—
8
V
VEXT
Voltage on EXT Output
—
—
8
V
VOUT
Output Voltage
VOUT
Load Regulation
VIN - VOUT
IDD
ISHDN
0.98 X VR VR ±0.5% 1.02 X VR
V
Test Conditions
IOUT = 50mA (Note 1)
60
mV
1mA  IOUT 100mA (Note 3)
100
—
mV
IOUT = 100mA (Note 2)
50
80
A
VSHDN = VIN = 5V
-60
—
Dropout Voltage
—
Supply Current
—
Shutdown Supply Current
—
—
0.6
A
VOUT/VIN Line Regulation
—
0.1
0.3
%/V
VOUT/T
VOUT Temperature Coefficient
—
±100
—
ppm/°C
ILEXT
EXT Pin Leakage Current
—
—
0.5
A
IEXT
EXT Sink Current
—
—
25
mA
VIH
SHDN Input High Logic Threshold
1.5
—
—
V
VIL
SHDN Input Low Logic Threshold
—
—
0.25
V
IIH
SHDN Input Current @ VIH
SHDN Input Current @ VIL
—
—
0.1
A
VSHDN = VIN = 5V
-0.2
-0.05
0
A
VSHDN = GND
IIL
Note
1:
2:
3:
4:
VSHDN = GND
IOUT = 50mA, 4V VIN 8V
(Note 3)
IOUT = 10mA, -40°C <TJ85°C
(Note 3)
Note 4
VR is the regulator output voltage setting.
Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal value measured at a
1V differential.
Varies with type of pass transistor used. Numbers shown are for the test circuit of Figure 3-1.
The product of IEXT X VEXT must be less than the maximum allowable power dissipation.
DS21437C-page 2
 2001-2012 Microchip Technology Inc.
TC57
2.0
PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 2-1.
TABLE 2-1:
PIN FUNCTION TABLE
Pin No.
(5-Pin SOT-23A)
Symbol
1
GND
2
VIN
3
VOUT
4
EXT
5
SHDN
Description
Ground terminal.
Supply voltage input. Positive input voltage of 2.7V to 8.0V.
Regulator voltage sense input. Connects to the collector of the external PNP pass transistor.
Base Drive for the external PNP pass transistor.
Shutdown Input. The device is enabled when SHDN VIL. The device enters a low power
shutdown state when SHDN VIH. During shutdown, the output is disabled, and supply current
falls to less than 1A.
 2001-2012 Microchip Technology Inc.
DS21437C-page 3
TC57
3.0
DETAILED DESCRIPTION
3.2
The TC57 series of precision low dropout regulator
controllers use an external PNP transistor to
accommodate a wide range of output currents. A series
resistor (RB) limits the maximum base current drawn
from the PNP transistor. Limiting the base drive both
determines the regulator’s output current capability, as
well as limits ground current when the device is
operated in dropout. The PNP transistor’s VCE(SAT) is
the only factor limiting dropout voltage.
Base-Current Limiting Resistor
Base current limiting resistor RB can be estimated
using:
EQUATION 3-3:
RB =
hFE (VIN – VBE)
IOUT
Where:
hFE is the current gain of the pass transistor
FIGURE 3-1:
TEST CIRCUIT
FZT749
Q1
VIN
RBE
33K
CIN
10μF
(Tantalum)
IOUT is the output current (in Amps)
VOUT
3
CL
10μF
(Tantalum)
RL
TC573002ECT
OFF
ON
5
VBE is the base-emitter voltage at the desired
output current (in volts)
VOUT
RB
680Ω
4
EXT
2 V
IN
VIN Is the input voltage (in volts)
SHDN
GND
1
For example, assume a desired continuous output
current of 1.0A, an input voltage of 5V, and an FZT749
pass transistor. The FZT749 has a typical hFE of 170,
and a VBE of 0.8V; both specified at a collector current
of 1.0A. Substituting these values into the equation
above results in an RB value of 704 (closest standard
value = 680).
3.3
3.1
Transistor Selection
The PNP pass transistor must have satisfactory power
dissipation, current gain, and collector current specifications to suit the application at hand. The maximum
output current the circuit can deliver is influenced by
hFE. The highest guaranteed output current is given by:
EQUATION 3-1:
ILOAD(MAX) = 25 mA x hFE(MIN)
The transistor’s actual power dissipation (PD) is equal
to the maximum load current times the maximum input/
output voltage differential, or:
EQUATION 3-2:
PD  ILOAD(MAX) x (VIN(MAX) – VOUT(MIN))
The ideal transistor has a minimum hFE of 100, and a
VCE(SAT) of less than 0.6V at full output current. For
example, the Zetex FZT749 has an hFE of 170 at a
collector current of 1A, and a guaranteed VCE(SAT) of
0.3V at a base current of 100mA. It is packaged in a
SOT-223 and is recommended for use with the TC57.
Other transistors are also suitable, depending on the
required input and output voltages and output current
(Table 3-1).
DS21437C-page 4
Pull-Up Resistor and Output
Capacitor
A pull-up resistor (RBE, installed between the base and
emitter of the pass transistor) facilitates rapid turn-off of
the pass transistor in the event of a sudden decrease in
load (Figure 3-2). Recommended values for this
resistor are between 20K and 47K. A Tantalum
output capacitor of at least 10F must be used to
guarantee stability. Higher values decrease output
noise and eliminate power-on overshoot, but extend
power-up times. Table 3-1 lists several capacitor
choices.
FIGURE 3-2:
3.3V, 1A REGULATOR
USING 5V SUPPLY INPUT
FZT749
Q1
VIN = 5V
RBE
33KΩ
CIN
10μF
(Tantalum)
RB
680Ω
4
EXT
OFF ON
5
COUT
10μF
(Tantalum)
VOUT 3
2 V
IN
1
VOUT = 3.3V
TC57
GND
SHDN
 2001-2012 Microchip Technology Inc.
TC57
3.4
Input Capacitor
3.5
The addition of an input capacitor further reduces
output noise, and negates the effects of power supply
input impedance. A 10F (min) Tantalum capacitor is
recommended.
TABLE 3-1:
Shutdown Mode
The TC57 enters a low power shutdown mode when
the shutdown input (SHDN) is high. During shutdown,
the regulator is disabled, the output capacitor is
discharged through the load, and supply current to the
TC57 decreases to less than 1A. Normal operation
resumes when SHDN is brought low. If the shutdown
mode is not used, SHDN should be tied to VIN.
COMPONENT SUPPLIERS
Device
Mounting
Method
Manufacturer
Website
CAPACITORS
267 Series
Matsuo
F95 Tantalum Series
Surface Mount
Surface Mount
Nichicon
http://www.matsuoelectronics.com
http://www.nichicon-us.com
595 Tantalum Series
Surface Mount
Sprague
http://www.vishay.com/brands/sprague
OS-CON Series
Through-Hole
Sanyo
LXF Series
Through-Hole
United Chemi-Con
http://chemi-con.com
ZTX749
Through-Hole
Zetex
http://www.zetex.com
2N4403
Through-Hole
ON SEMI
http://www.onsemi.com/home
2N2907A
Through-Hole
ON SEMI
http://www.onsemi.com/home
FZT749
Surface Mount
Zetex
http://www.sanyovideo.com
TRANSISTORS
 2001-2012 Microchip Technology Inc.
http://www.zetex.com
DS21437C-page 5
TC57
4.0
TYPICAL CHARACTERISTICS
Note:
The graphs and tables provided following this note are a statistical summary based on a limited number of
samples and are provided for informational purposes only. The performance characteristics listed herein are
not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified
operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
1. OUTPUT VOLTAGE vs. OUTPUT CURRENT
TC575002 (5V)
TC574002 (4V)
TA = 25°C
VIN = 6V, CL = 10μF (Tantalum)
5.1
TA = 25°C
VIN = 4.3V, CL = 10μF (Tantalum)
5.0
4.9
4.8
4.7
3.4
OUTPUT VOLTAGE VOUT (V)
4.1
OUTPUT VOLTAGE VOUT (V)
OUTPUT VOLTAGE VOUT (V)
TC573302 (3.3V)
TA = 25°C
VIN = 5V, CL = 10μF (Tantalum)
4.0
3.9
3.8
3.7
0
100
200
300
400
500
3.3
3.2
3.1
3.0
0
OUTPUT CURRENT IOUT (mA)
100
200
400
300
0
500
100
200
300
400
500
OUTPUT CURRENT IOUT (mA)
OUTPUT CURRENT IOUT (mA)
2. OUTPUT VOLTAGE vs. INPUT VOLTAGE
TC575002 (5V)
CL = 10μF (Tantalum), TA = 25°C
4.2
IOUT = 1mA
500mA
4.8
4.6
100mA
4.4
4.2
4.5
IOUT = 1mA
5.05
500mA
5.00
100mA
4.95
4.90
5
5.5
INPUT VOLTAGE VIN (V)
TC574002 (4V)
IOUT = 1mA
100mA, 500mA
3.90
3.85
5
6
INPUT VOLTAGE VIN (V)
DS21437C-page 6
100mA
3.4
8
7
4.0
4.5
INPUT VOLTAGE VIN (V)
TC573302 (3.3V)
CL = 10μF (Tantalum), TA = 25°C
3.5
OUTPUT VOLTAGE VOUT (V)
4.05
4
3.6
TC573302 (3.3V)
4.10
3.95
7
500mA
3.8
INPUT VOLTAGE VIN (V)
CL = 10μF (Tantalum), TA = 25°C
4.00
6
IOUT = 1mA
A
4.0
3.2
3.5
4.85
5.0
CL = 10μF (Tantalum), TA = 25°C
3.40
OUTPUT VOLTAGE VOUT (V)
5.0
OUTPUT VOLTAGE VOUT (V)
OUTPUT VOLTAGE VOUT (V)
OUTPUT VOLTAGE VOUT (V)
CL = 10μF (Tantalum), TA = 25°C
5.10
5.2
OUTPUT VOLTAGE VOUT (V)
TC574002 (4V)
TC575002 (5V)
CL = 10μF (Tantalum), TA = 25°C
3.3
IOUT = 1mA
500mA
3.1
2.9
100mA
2.7
2.5
2.8
3.35
IOUT = 1mA, 100mA
3.30
500mA
3.25
3.20
3.15
3.3
INPUT VOLTAGE VIN (V)
3.8
3
4
5
INPUT VOLTAGE VIN (V)
6
 2001-2012 Microchip Technology Inc.
TC57
4.0
TYPICAL CHARACTERISTICS (CONTINUED)
3. DROPOUT VOLTAGE vs. OUTPUT CURRENT
TC575002 (5V)
TC574002 (4V)
1.0
CL = 10μF (Tantalum)
1.0
0.8
0.6
0.4
80°C
TOPR = 25°C
0.2
-3
30°C
0.0
0
200
400
600
800
DROPOUT VOLTAGE VIN -VOUT
1.0
DROPOUT VOLTAGE VIN -VOUT
DROPOUT VOLTAGE VIN -VOUT
TC573302 (3.3V)
CL = 10μF (Tantalum)
CL = 10μF (Tantalum)
0.8
0.6
0.4
80°C
TOPR
R = 25°C
0.2
-30
0°C
0.0
1000
0
200
OUTPUT CURRENT IOUT (mA)
400
800
600
0.8
0.6
80°C
0.4
TOPR = 25°
25°C
0.2
-30°C
0.0
0
1000
200
OUTPUT CURRENT IOUT (mA)
400
800
600
1000
OUTPUT CURRENT IOUT (mA)
4. SUPPLY CURRENT vs. INPUT VOLTAGE
TC575002 (5V)
TC574002 (4V)
TC573302 (3.3V)
50
40
TOPR = 25°C, 80°C
30
-30°C
20
10
0
50
SUPPLY CURRENT IDD (μA)
SUPPLY CURRENT IDD (μA)
SUPPLY CURRENT IDD (μA)
50
40
30
TOPR = 25°C, 80°C
20
-30°C
10
0
5
6
7
8
40
30
TOPR = 25°C, 80°C
20
-30°C
10
0
4
5
INPUT VOLTAGE VIN (V)
6
7
3
4
6
5
INPUT VOLTAGE VIN (V)
INPUT VOLTAGE VIN (V)
TC574002 (4V)
TC573302 (3.3V)
5. OUTPUT VOLTAGE vs. AMBIENT TEMPERATURE
TC575002 (5V)
VIN = 5.0V
IOUT = 100mA, CL = 10μF (Tantalum)
VIN = 6.0V
IOUT = 100mA, CL = 10μF (Tantalum)
OUTPUT VOLTAGE VOUT (V)
OUTPUT VOLTAGE VOUT (V)
5.05
5.00
4.95
-20
0
20
40
60
AMBIENT TEMP. TA (°C)
 2001-2012 Microchip Technology Inc.
80
3.40
OUTPUT VOLTAGE VOUT (V)
4.10
5.10
4.90
-40
VIN = 4.3V
IOUT = 100mA, CL = 10μF (Tantalum)
4.05
4.00
3.95
3.90
-40
3.35
3.30
3.25
3.20
-20
20
40
60
0
AMBIENT TEMP. TA (°C)
80
-40
-20
0
20
40
60
80
AMBIENT TEMP. TA (°C)
DS21437C-page 7
TC57
4.0
TYPICAL CHARACTERISTICS (CONTINUED)
6. SUPPLY CURRENT vs. AMBIENT TEMPERATURE
TC575002 (5V)
TC574002 (4V)
50
30
20
10
0
-40
SUPPLY CURRENT IDD (μA)
40
40
30
20
10
0
20
40
60
80
40
30
20
10
0
0
-20
VIN = 4.3V
50
50
SUPPLY CURRENT IDD (μA)
SUPPLY CURRENT IDD (μA)
TC573302 (3.3V)
VIN = 5V
VIN = 6V
-40
AMBIENT TEMP. TA (°C)
-20
0
20
40
60
AMBIENT TEMP. TA (°C)
80
-40
0
20
40
60
-20
AMBIENT TEMP. TA (°C)
80
7. INPUT TRANSIENT RESPONSE
TC575002 (5V)
TC575002 (5V)
IOUT = 100mA, CL = 10μF (Tantalum)
8
Input Voltage
5.3
6
5.2
5
Output Voltage
5.1
4
5.0
3
4.9
7
5
3
4.9
TC574002 (4V)
7
4.3
5
4.2
4.1
3
4.0
2
3.9
INPUT VOLTAGE VIN (V)
Input Voltage
OUTPUT VOLTAGE VOUT (V)
INPUT VOLTAGE VIN (V)
5.1
IOUT = 100mA, CL = 10μF (Tantalum)
6
DS21437C-page 8
Output Voltage
Time (0.4 msec/div)
4.4
Time (0.4 msec/div)
5.2
5.0
TC574002 (4V)
Output Voltage
5.3
4
IOUT = 10mA, CL = 10μF (Tantalum)
4
Input Voltage
6
Time (0.4 msec/div)
7
5.4
4.4
Input Voltage
6
4.3
5
4.2
4
Output Voltage
4.1
3
4.0
2
3.9
OUTPUT VOLTAGE VOUT (V)
7
INPUT VOLTAGE VIN (V)
5.4
OUTPUT VOLTAGE VOUT (V)
INPUT VOLTAGE VIN (V)
8
OUTPUT VOLTAGE VOUT (V)
IOUT = 10mA, CL = 10μF (Tantalum)
Time (0.4 msec/div)
 2001-2012 Microchip Technology Inc.
TC57
4.0
TYPICAL CHARACTERISTICS (CONTINUED)
7. INPUT TRANSIENT RESPONSE (CONT.)
TC573302 (3.3V)
TC573302 (3.3V)
6
IOUT = 100mA, CL = 10μF (Tantalum)
6
3.7
3.6
4
3.5
3
Output Voltage
3.4
2
3.3
1
3.2
INPUT VOLTAGE VIN (V)
5
3.7
Input Voltage
OUTPUT VOLTAGE VOUT (V)
INPUT VOLTAGE VIN (V)
Input Voltage
5
3.6
4
3.5
3
3.4
Output Voltage
2
3.3
1
3.2
Time (0.4 msec/div)
OUTPUT VOLTAGE VOUT (V)
IOUT = 10mA, CL = 10μF (Tantalum)
Time (0.4 msec/div)
8. LOAD TRANSIENT RESPONSE
TC575002 (5V)
TC574002 (4V)
Output Voltage
800
600
5.00
4.95
Output Current
400
300mA
200
4.90
4.85
1mA
0
OUTPUT VOLTAGE VOUT (V)
5.05
OUTPUT CURRENT IOUT (mA)
1000
5.10
OUTPUT VOLTAGE VOUT (V)
VIN = 5V, CL = 10μF (Tantalum)
4.10
1000
4.05
800
4.00
600
400
3.95
Output Current
300mA
200
3.90
3.85
Time (10 msec/div)
Output Voltage
1mA
OUTPUT CURRENT IOUT (mA)
VIN = 6V, CL = 10μF (Tantalum)
0
Time (10 msec/div)
TC573302 (3.3V)
VIN = 4.3V, CL = 10μF (Tantalum)
OUTPUT VOLTAGE VOUT (V)
Output Voltage
3.35
800
3.30
600
3.25
Output Current
400
300mA
200
3.20
3.15
1mA
OUTPUT CURRENT IOUT (mA)
1000
3.40
0
Time (10 msec/div)
 2001-2012 Microchip Technology Inc.
DS21437C-page 9
TC57
5.0
PACKAGING INFORMATION
5.1
Package Marking Information
2
3
1
5.2
3
represents integer part of output voltage
Symbol
Voltage
2
3
4
5
6
2.
3.
4.
5.
6.
represents first decimal of output voltage
Symbol
Voltage
Symbol
Voltage
0
1
2
3
4
.0
.1
.2
.3
.4
5
6
7
8
9
.5
.6
.7
.8
.9
represents production lot ID code
Taping Form
Component Taping Orientation for 5-Pin SOT-23A (EIAJ SC-74A) Devices
User Direction of Feed
Device
Marking
W
PIN 1
P
Standard Reel Component Orientation
TR Suffix Device
(Mark Right Side Up)
Carrier Tape, Number of Components Per Reel and Reel Size
Package
5-Pin SOT-23A
DS21437C-page 10
Carrier Width (W)
Pitch (P)
Part Per Full Reel
Reel Size
8 mm
4 mm
3000
7 in
 2001-2012 Microchip Technology Inc.
TC57
5.3
Package Dimensions
Note:
For the most current package drawings, please see the Microchip Packaging Specification located
at http://www.microchip.com/packaging
SOT-23A-5
.075 (1.90)
REF.
.071 (1.80)
.059 (1.50)
.122 (3.10)
.098 (2.50)
.020 (0.50)
.012 (0.30)
PIN 1
.037 (0.95)
REF.
.122 (3.10)
.106 (2.70)
.057 (1.45)
.035 (0.90)
.006 (0.15)
.000 (0.00)
.010 (0.25)
.004 (0.09)
10° MAX.
.024 (0.60)
.004 (0.10)
Dimensions: inches (mm)
 2001-2012 Microchip Technology Inc.
DS21437C-page 11
TC57
6.0
REVISION HISTORY
Revision C (November 2012)
Added a note to the package outline drawing.
DS21437C-page 12
 2001-2012 Microchip Technology Inc.
TC57
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART CODE TC57
XX
02
ECT
XX
Output Voltage:
Ex: 30 = 3.0V
Tolerance:
2 = ±2%
Temperature/Package:
E: -40°C to +85°C
CT: 5-Pin SOT-23A
Taping Direction:
TR: Standard Taping
Sales and Support
Data Sheets
Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following:
1.
2.
Your local Microchip sales office
The Microchip Worldwide Site (www.microchip.com)
Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using.
New Customer Notification System
Register on our web site (www.microchip.com/cn) to receive the most current information on our products.
 2001-2012 Microchip Technology Inc.
DS21437C-page13
TC57
NOTES:
DS21437C-page14
 2001-2012 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, dsPIC,
FlashFlex, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro,
PICSTART, PIC32 logo, rfPIC, SST, SST Logo, SuperFlash
and UNI/O are registered trademarks of Microchip Technology
Incorporated in the U.S.A. and other countries.
FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor,
MTP, SEEVAL and The Embedded Control Solutions
Company are registered trademarks of Microchip Technology
Incorporated in the U.S.A.
Silicon Storage Technology is a registered trademark of
Microchip Technology Inc. in other countries.
Analog-for-the-Digital Age, Application Maestro, BodyCom,
chipKIT, chipKIT logo, CodeGuard, dsPICDEM,
dsPICDEM.net, dsPICworks, dsSPEAK, ECAN,
ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial
Programming, ICSP, Mindi, MiWi, MPASM, MPF, MPLAB
Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code
Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit,
PICtail, REAL ICE, rfLAB, Select Mode, SQI, Serial Quad I/O,
Total Endurance, TSHARC, UniWinDriver, WiperLock, ZENA
and Z-Scale are trademarks of Microchip Technology
Incorporated in the U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
GestIC and ULPP are registered trademarks of Microchip
Technology Germany II GmbH & Co. & KG, a subsidiary of
Microchip Technology Inc., in other countries.
All other trademarks mentioned herein are property of their
respective companies.
© 2001-2012, Microchip Technology Incorporated, Printed in
the U.S.A., All Rights Reserved.
Printed on recycled paper.
ISBN: 9781620767436
QUALITY MANAGEMENT SYSTEM
CERTIFIED BY DNV
== ISO/TS 16949 ==
 2001-2012 Microchip Technology Inc.
Microchip received ISO/TS-16949:2009 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
DS21437C-page 15
Worldwide Sales and Service
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Web Address:
www.microchip.com
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-3090-4444
Fax: 91-80-3090-4123
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
India - Pune
Tel: 91-20-2566-1512
Fax: 91-20-2566-1513
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Japan - Osaka
Tel: 81-66-152-7160
Fax: 81-66-152-9310
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Cleveland
Independence, OH
Tel: 216-447-0464
Fax: 216-447-0643
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Santa Clara
Santa Clara, CA
Tel: 408-961-6444
Fax: 408-961-6445
Toronto
Mississauga, Ontario,
Canada
Tel: 905-673-0699
Fax: 905-673-6509
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
China - Beijing
Tel: 86-10-8569-7000
Fax: 86-10-8528-2104
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
China - Chongqing
Tel: 86-23-8980-9588
Fax: 86-23-8980-9500
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
China - Hangzhou
Tel: 86-571-2819-3187
Fax: 86-571-2819-3189
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
China - Hong Kong SAR
Tel: 852-2401-1200
Fax: 852-2401-3431
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Taiwan - Hsin Chu
Tel: 886-3-5778-366
Fax: 886-3-5770-955
China - Shenzhen
Tel: 86-755-8203-2660
Fax: 86-755-8203-1760
Taiwan - Kaohsiung
Tel: 886-7-213-7828
Fax: 886-7-330-9305
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Taiwan - Taipei
Tel: 886-2-2508-8600
Fax: 886-2-2508-0102
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
UK - Wokingham
Tel: 44-118-921-5869
Fax: 44-118-921-5820
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
DS21437C-page 16
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Japan - Yokohama
Tel: 81-45-471- 6166
Fax: 81-45-471-6122
10/26/12
 2001-2012 Microchip Technology Inc.