快速入门指南

CY8CKIT-143 PSOC® 4 BLE 256K MODULE
CY8CKIT-143 PSoC® 4 BLE 256K Module is an easy-to-use solution for creating a
complete BLE system. It features a PSoC 4 BLE device with 256 KB internal flash,
24-MHz and 32.768-kHz crystals, a PCB antenna, and other passives while
providing access to all GPIOs of the device.
For more information on Cypress’s BLE solutions visit www.cypress.com/BLE
PSoC 4 BLE is an ARM® Cortex®-M0 based single-chip solution that integrates a
programmable analog front end, programmable digital peripherals, CapSense®
touch-sensing technology, and a Bluetooth® Low Energy or Bluetooth Smart radio.
Antenna matching
network (AMN)
Wiggle antenna
Ctank
Cmod
24-MHz crystal
P0_1
P0_3
P0_5
P1_0
P1_2
P0_6
P0_7
XRES
GND
VDDD
P0_0
P0_2
P0_4
VREF
P1_1
P1_4
P1_3
P1_5
P1_7
P1_6
GND
P3_6
P3_4
P3_2
P3_0
P4_0
P4_1
P2_6
P2_4
P2_2
P2_0
VDDR
CY8C4248LQI-BL483
PSoC 4 BLE device
VDD
GND
P1_5
P1_4
SAR bypass capacitor
(bottom side)
VDDA
P3_7
P3_5
P3_3
P3_1
P5_1
P5_0
P2_7
P2_5
P2_3
P2_1
GND
32.768-kHz crystal
(bottom side)
4-pin UART header
Fig-1: Pinout Description for PSoC 4 BLE Module
Note: To apply power to the module, use the VDD pin (1.9 V - 5.0 V) and GND pin.
CY8CKIT-143 PSOC® 4 BLE 256K MODULE
STANDALONE USE WITH PSOC CREATORTM IDE AND CY8CKIT-002 MINIPROG3
Step 1: Select the 5-pin connector setting in PSoC Creator or PSoC Programmer.
Step 2: Use 0.1” male headers (not included) or jumper wires to connect the
MiniProg3 to the module.
Pin Mapping
CY8CKIT-002
VTARG
CY8CKIT-143
VDD
GND
GND
RES
XRES
SCLK
P0_7
SDAT
P0_6
Fig-2: Programming and Debugging with CY8CKIT-002 MiniProg3
USING THE CY8CKIT-143 MODULE WITH CY8CKIT-042-BLE PIONEER KIT
Step 1: Plug the module on the CY8CKIT-042-BLE Pioneer Kit Baseboard.
Step 2: Create your design in PSoC Creator IDE and use the BLE Pioneer Kit to
program and debug.
Fig-3: Programming and Debugging with CY8CKIT-042-BLE Pioneer Baseboard
The CY8CKIT-143 module is intended to be used for evaluation of hardware and
software in a laboratory environment. This module radiates radio frequency energy
and has not been tested for compliance with limits applicable under any standard.
Operation of this module may cause interference with radio communications. Cypress
recommends that the module should only be used in a shielded room.
Contact [email protected] for details.
For more information about this kit, visit www.cypress.com/CY8CKIT-143
© 2015 Cypress Semiconductor Corporation. All rights reserved.
All trademarks or registered trademarks referenced herein are the
properties of their respective owners. 001-97333 Rev.**