DC1639A - Demo Manual

DEMO MANUAL DC1639
LTC6360
High Speed Op Amp with
True Zero Output
DESCRIPTION
Demonstration circuit 1639 allows quick setup of the
LTC6360 true zero op amp. The op amp is configured as
a unity gain buffer, with landing pads provided to make
other gains configurable. Ample bypass is provided for
both the input supply and for the –0.6V on-chip charge
pump. The recommended 10Ω 330pF output compensation is provided on board for unity-gain stability. If this
compensation is removed, gain bandwidth increases but
the op amp is stable only in gains of four and higher.
Design files for this circuit board are available at
http://www.linear.com/demo
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear
Technology Corporation. All other trademarks are the property of their respective owners.
OPERATING PRINCIPLES
Most op amps which operate on single supplies have
outputs that cannot get all the way to ground. The saturation of their output devices leave 10’s of millivolts of
output voltage error when the output tries to swing to
ground. The LTC6360 has an onboard charge pump that
creates a –0.6V internal supply for the output stage, so
it can swing all the way to ground and even a little below
ground.
QUICK START PROCEDURE
Demonstration circuit 1639 is simple to use, with only one
jumper provided to allow the shutdown option.
1. Set the power supply to 5V, then turn off the power
supply. As shown in Figure 1, connect the +5V lead
from the power supply to the V+ terminal of the demo
circuit, and connect the COM side of the supply to the
GND terminal of the demo circuit.
2. Turn on the supply. Note that without input exciatation
the output is very near 0mV, much closer to ground
than most op amps can achieve.
3. You are now free to connect a source to the input and
exercise the LTC6360. The input range is 0V to about
4.25V. (Under high frequency large signal swing exciatation, you may see some odd behavior as the negative
charge pump voltage begins to safely collapse.)
to the schematic in Figure 2. Install appropriate resistors at R7 and R6, and install appropriate impedances
at C7 and R5 (shorts and/or blocking capacitance). The
time domain and frequency responses can be adjusted
using a small capacitance at C8.
5. For inverting gain, install J2 and appropriate passives
in the path to the –input. For inverting gains, the
+input must be biased up at some voltage. Installing
R13 connects the +input to the “EXT_VCM” turret which
is biased nominally at 2V by R11 and R12, or the turret
can be driven with an external supply.
6. Shutdown: The LTC6360 can be shut down by moving
the shunt on JP1 from the “Enable” position to the “Disable” position. It can also be shut down and reactivated
electrically via the SHDN turret, in which case the shunt
on JP1 should be removed entirely.
4. If you want to set the LTC6360 for some other positive
gain, turn off the supply and disconnect the board. Refer
dc1639f
1
DEMO MANUAL DC1639
QUICK START PROCEDURE
Figure 1. Proper Equipment Setup.
PARTS LIST
ITEM
QTY REFERENCE
Required Circuit Components
1
2
C1, C5
2
0
C2, C6
3
0
C3, C7
4
3
C4, C10, C13
5
0
C8
6
1
C9
7
3
C11, C12, C14
8
1
C15
9
0
C16
10
5
E1-E5
11
1
JP1
12
1
XJP1
13
2
J1, J3
14
0
J2
15
6
R1,R3, R7, R9, R14, R15
16
1
R2
17
0
R4, R6, R10, R13
18
0
R5
19
1
R8
20
1
R11
21
1
R12
22
4
MH1-MH4 (STAND-OFF)
23
1
U1
24
1
25
1
STENCIL FOR TOP SIDE
PART DESCRIPTION
MANUFACTURER/PART NUMBER
CAP., X7R, 1μF, 16V, 10% 0603
CAP., 0805
CAP., 0603
CAP., X7R, 0.1μF, 25V, 10% 0603
CAP., 0603, NPO
CAP., X7R, 0.01μF, 50V, 10% 0603
CAP., X5R, 10μF, 6.3V, 20% 0805
CAP.,CERM 330pF, 50V, NPO, 0805
CAP., 0805, NPO
TESTPOINT, TURRET, .065" PBF
HEADER, 3 PINS, 2mm
SHUNT, 2mm CENTER
CONN, BNC, SMA 50Ω EDGE-LANCH
CONN, BNC, SMA 50Ω EDGE-LANCH
RES., CHIP, 0, 1/10W, 0603
RES., CHIP, 49.9, 1/8W, 1% 0805
RES., 0603
RES., 0805
RES., CHIP, 10, 1/10W, 1% 0603
RES., CHIP, 30.1k, 1/10W, 1% 0603
RES., CHIP, 20k, 1/10W, 1% 0603
STAND-OFF, NYLON (SNAP ON), 0.50" TALL
LOW NOISE ADC DRIVER W/TRUE ZERO OUTPUT
FAB, PRINTED CIRCUIT BOARD
STENCIL
AVX, 0603YC105KAT2A
OPT
OPT
AVX, 06033C104KAT2A
OPT
AVX, 06035C103KAT2A
AVX, 08056D106MAT2A
AVX, 08055A331JAT2A OPT
MILL-MAX, 2308-2-00-80-00-00-07-0
SAMTEC, TMM-103-02-L-S
SAMTEC, 2SN-BK-G
E. F. JOHNSON, 142-0701-851
OPT
VISHAY, CRCW06030000Z0EA
VISHAY, CRCW080549R9FKEA
OPT
OPT
VISHAY, CRCW060310R0FKEA
VISHAY, CRCW060330K1FKEA
VISHAY, CRCW060320K0FKEA
KEYSTONE, 8833(SNAP ON)
LINEAR TECH., LTC6360CMS8E#TRPBF
DEMO CIRCUIT #1639A
STENCIL 1639A
dc1639f
2
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
A
B
C
D
J1
SMA
5
R3 = 0
R13 = OPEN
INSTALL
NOT INSTALL
DC MODE (SHOWN)
- IN
INSTALL
INSTALL
* SEE TABLE BELOW FOR ALTERNATE VALUES
+ IN
J2
SMA
GND
E4
C6
OPT
0805
R4
OPT
R13 = 10k
R3 = 1uF
AC MODE
C2
OPT
0805
R1
0
R12
20k
R11
30.1k
4
0
GND
E5
R2
49.9
0805
R5
OPT
0805
* R3
C1
1uF
EXT
VCM
E1
C7
OPT
C3
OPT
*
DISABLE
ENABLE
R6
OPT
OPT
R13
V+
R7
0
2
JP1
SHDN
E2
3
C4
.1uF
**
R8
10
C16
OPT
NPO
0805
J3
SMA
C14
10uF
0805
OUT
R15
0
C9
.01uF
CUSTOMER NOTICE
0
R9
R10
OPT
C13
.1uF
VCC
9
LTC6360CMS8E
U1
Figure 2
3
THIS CIRCUIT IS PROPRIETARY TO LINEAR TECHNOLOGY AND
SUPPLIED FOR USE WITH LINEAR TECHNOLOGY PARTS.
LINEAR TECHNOLOGY HAS MADE A BEST EFFORT TO DESIGN A
CIRCUIT THAT MEETS CUSTOMER-SUPPLIED SPECIFICATIONS;
HOWEVER, IT REMAINS THE CUSTOMER'S RESPONSIBILITY TO
VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL
APPLICATION. COMPONENT SUBSTITUTION AND PRINTED
CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT
PERFORMANCE OR RELIABILITY. CONTACT LINEAR
TECHNOLOGY APPLICATIONS ENGINEERING FOR ASSISTANCE.
C15
330pF
NPO
0805
**
OPT
NPO
C8
R14
0
C5
1uF
GND
-IN
1
7
SHDN
OUT
2
6
CPI
VCC
3
VCC
4
1
3
8
+IN
5
CPO
VDD
4
5
C11
10uF
0805
E3
2
SCALE = NONE
NC
GLEN B.
PCB DES.
APP ENG.
APPROVALS
V+
V+
4.75V - 5.25V
C10
.1uF
2
DATE:
N/A
SIZE
1
REVISION HISTORY
PRODUCTION FAB
DESCRIPTION
GLEN B.
APPROVED
DATE
1630 McCarthy Blvd.
Milpitas, CA 95035
Phone: (408)432-1900 www.linear.com
Fax: (408)434-0507
LTC Confidential-For Customer Use Only
03-29-11
03-29-11
IC NO.
1
LTC6360CMS8E
DEMO CIRCUIT 1639A
SHEET 1
OF
1
2
REV.
LOW NOISE ADC DRIVER W / TRUE ZERO OUTPUT
TECHNOLOGY
FOR STABILITY.
** R8 AND C15 ARE NEEDED
NOTE: UNLESS OTHERWISE SPECIFIED ALL
RESISTORS: OHMS, 0603, 1%, 1/10W
2
-
TITLE: SCHEMATIC
C12
10uF
0805
REV
ECO
A
B
C
D
DEMO MANUAL DC1639
SCHEMATIC DIAGRAM
dc1639f
3
DEMO MANUAL DC1639
DEMONSTRATION BOARD IMPORTANT NOTICE
Linear Technology Corporation (LTC) provides the enclosed product(s) under the following AS IS conditions:
This demonstration board (DEMO BOARD) kit being sold or provided by Linear Technology is intended for use for ENGINEERING DEVELOPMENT
OR EVALUATION PURPOSES ONLY and is not provided by LTC for commercial use. As such, the DEMO BOARD herein may not be complete
in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including but not limited to product safety
measures typically found in finished commercial goods. As a prototype, this product does not fall within the scope of the European Union
directive on electromagnetic compatibility and therefore may or may not meet the technical requirements of the directive, or other regulations.
If this evaluation kit does not meet the specifications recited in the DEMO BOARD manual the kit may be returned within 30 days from the date
of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY THE SELLER TO BUYER AND IS IN LIEU
OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS
FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THIS INDEMNITY, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR
ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user releases LTC from all claims
arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to take any and all
appropriate precautions with regard to electrostatic discharge. Also be aware that the products herein may not be regulatory compliant or
agency certified (FCC, UL, CE, etc.).
No License is granted under any patent right or other intellectual property whatsoever. LTC assumes no liability for applications assistance,
customer product design, software performance, or infringement of patents or any other intellectual property rights of any kind.
LTC currently services a variety of customers for products around the world, and therefore this transaction is not exclusive.
Please read the DEMO BOARD manual prior to handling the product. Persons handling this product must have electronics training and
observe good laboratory practice standards. Common sense is encouraged.
This notice contains important safety information about temperatures and voltages. For further safety concerns, please contact a LTC application engineer.
Mailing Address:
Linear Technology
1630 McCarthy Blvd.
Milpitas, CA 95035
Copyright © 2004, Linear Technology Corporation
dc1639f
4
Linear Technology Corporation
LT 0811 • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900
●
FAX: (408) 434-0507 ● www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2011