ES0315 Errata Sheet X-NUCLEO-CCA02M1 Board limitations Board identification This errata sheet applies to the X-NUCLEO-CCA02M1 digital MEMS microphones expansion board based on MP34DT01-M for STM32 Nucleo. The full list of part numbers is shown in the table below. Table 1. X-NUCLEO-CCA02M1, board summary Part numbers Device Info (indicated in a board corner) X-NUCLEO-CCA02M1 "1511" Figure 1. X-NUCLEO-CCA02M1, board marking (upper right corner) July 2015 DocID028104 Rev 1 1/5 www.st.com Contents ES0315 Contents 1 Limitation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1 2 2/5 Oversized ST Morpho connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1.1 Part number affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1.2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1.3 Workaround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 DocID028104 Rev 1 ES0315 Limitation 1 Limitation 1.1 Oversized ST Morpho connector 1.1.1 Part number affected X-NUCLEO-CCA02M1 digital MEMS microphones expansion board based on MP34DT01-M for STM32 Nucleo. 1.1.2 Description These boards mount a 2 x 20 ST Morpho connector instead of the 2 x 19 one. It could cause incorrect alignment of this board on the STM32 Nucleo. 1.1.3 Workaround The workaround is to carefully mount the X-NUCLEO-CCA02M1 over the STM32 Nucleo board and verify they are aligned as in Figure 2 before supplying power to the boards. Figure 2. Correct mounting DocID028104 Rev 1 3/5 5 Revision history 2 ES0315 Revision history Table 2. Document revision history 4/5 Date Revision 10-Jul-2015 1 Changes Initial release. DocID028104 Rev 1 ES0315 IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2015 STMicroelectronics – All rights reserved DocID028104 Rev 1 5/5 5