DEMO MANUAL DC2227A LT3669-2 IO-Link Device with Multiple Sensors Description Demonstration circuit 2227A is a complete IO-Link® device built using the LT®3669-2 to implement an IO-Link v1.1 physical interface (PHY). The IO-Link stack protocol runs on an Atmel ATmega microcontroller which connects to LT3669-2’s logic IO-signals to communicate with an IO-Link master via the CQ1 transceiver. An LTC2997 temperature sensor, an opto-coupler (light barrier) and a pushbutton demonstrate IO-Link device functionality and master-slave interoperability. A 28V/100mA light bulb connected to LT3669-2’s second driver (Q2) demonstrates its high current driving capabilities. All low voltage circuitry is supplied by the LT3669-2’s integrated buck and LDO for high efficiency. Design files for this circuit board are available at http://www.linear.com/demo/DC2227A L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear Technology Corporation. IO-Link is a registered trademark of PROFIBUS User Organization (PNO). All other trademarks are the property of their respective owners. Performance Summary Specifications are at TA = 25°C, VL+ = 24V SYMBOL PARAMETER CONDITIONS L+ Input Supply VBUCK LT3669-2's Buck Output Voltage 3.8 4 4.2 V VLDO LT3669-2's LDO Output Voltage 3.135 3.3 3.465 V MIN TYP 18 MAX 36 UNITS V Board Photo dc2227af 1 DEMO MANUAL DC2227A Quick Start Procedure Additional Hardware and Software Requirements Operation in COM2 To operate the DC2227A demo circuit in IO-Link mode, additional hardware and software are required: 7. Click on the “Select Device” button again, this time making sure the correct port is selected. Use the following IODD file: • PC running Windows XP or later with Ethernet Card. Alternatively a USB-to-Ethernet adaptor can also be used TEConcept_GmbH-65538-<YYYYMMDD>-IODD1.1.xml Set-up Preparation (See Figures 1 and 2) 8. If the device is off, switch it on, enabling the L+ supply of the connected master’s port by pressing the “Power ON” button keeping the light barrier open during power-up. If the device was already powered on coming from COM3 mode, power cycle it keeping the light barrier open to restart the device in COM2 mode. See the Light Barrier section for more information. 1. Download and install the DC2228A Control Tool software from: 9. Start IO-Link communication by pressing the “IO-Link” button. The “Min. Cycle Time” is set to 20ms. 10. If a different IODD file is to be selected, stop IO-Link communication first by pressing the “Inactive” button to revert the DC2227A into SIO mode. • LTC IO-Link Master Demo Circuit DC2228A • DC2228A Control Tool Software • PoE Injector or 24V Power Supply • DC2227A IODD Files (COM2 and COM3) www.linear.com/demo/DC2228A 2. Connect the DC2228A to power and the host computer. Refer to the DC2228A demo manual for detailed information about the different configuration options to supply the DC2228A and interface it to the PC. 3. Using a 3-wire IO-Link cable of up to 20m in length with M12 connectors, plug the male terminal to one of the 8-ports of the DC2228A (for example port 2 like in Figure 1) and the female terminal to the DC2227A. Operation in COM3 11. Click on the “Select Device” button again making sure the correct port is selected. Use the following IODD file: TEConcept_GmbH-65539-<YYYYMMDD>-IODD1.1.xml 4. Run the DC2228A Control Tool on the PC and connect to the DC2228A. See the DC2228A demo manual for detailed information of how to select the DC2228A as the master, configure the IP parameters and establish communication between the host computer and the master. 12. If the device is off, switch it on, enabling the L+ supply of the connected master’s port by pressing the “Power ON” button keeping the light barrier closed during power-up. If the device was already powered on coming from COM2 mode, power cycle it keeping the light barrier closed to restart the device in COM3 mode. See the Light Barrier section for more information. Operation in IO-Link Mode (See Figures 1 and 2) 13. Start IO-Link communication by pressing the “IO-Link” button. The “Min. Cycle time” is set to 800µs. 5. Download the DC2227A IODD files from: www.linear.com/demo/DC2227A 6. Click on the “Select Device” button and import the IODD files by selecting the downloaded xml files and then clicking on the “Import” button (one at a time). 2 14. If a different IODD file is to be selected, stop IO-Link communication first by pressing the “Inactive” button to revert the DC2227A in SIO mode. dc2227af DEMO MANUAL DC2227A Quick Start Procedure Figure 1. Recommended Set-up for Operating DC2227A in IO-Link Mode Figure 2. Control Tool for Connecting DC2227A to DC2228A dc2227af 3 DEMO MANUAL DC2227A additional information Operation in SIO Mode The device can also operate in SIO mode. In this mode, no IO-Link communication takes place either because the master connected to the device is in the “Inactive” mode and it only supplies power to the device, or because there is no master connected to the device in which case the device is powered by a 24V supply. In SIO mode, the DC2227A reacts to the status of the light barrier as follows: • If the light barrier is open, then drivers CQ1 and Q2 actively pull low. Since the onboard light bulb is connected between Q2 and ground, it is therefore turned off. • If the light barrier is closed (by placing a piece of paper in its gap), CQ1 and Q2 actively pull high and the light bulb attached to Q2 turns on. Temperature Sensor Configurations In IO-Link mode, the DC2227A reports cyclically to the master (and thus to the PC Control Tool) the temperature measured by the on-board LTC2997. In order to measure temperature the LTC2997 uses an NPN configured as a diode. The NPN can be either on-chip, on PCB (Q1) or remote. Refer to the Connectors and Jumpers section for detailed information on how to choose the NPN. Microcontroller ADC’s Offset Correction The 12-bit ADC of the Atmel microcontroller samples both, the precise 1.8V reference voltage (VREF) and the VPTAT outputs of the LTC2997 to report the temperature in Celsius to the IO-Link master. The temperature is then calculated using a ratiometric measurement. The µC’s ADC is specified to have offsets from –40 to 40 LSBs. The temperature equation is: 100• T(°C) = 4 ADC7 – OFFSET • 45000 – 27315 ADC4 – OFFSET ADC7 is the ADC’s code for the VPTAT output and ADC4 the code for the precise 1.8V VREF. OFFSET is the ADC’s offset (in LSB) parameter that can be set using the control tool (default is 0 LSB). In order to improve the accuracy of the temperature reading, a calibrated thermometer can be used to measure the temperature close to the LTC2997 and then the ADC Offset parameter can be set to the value (after several tries) that minimizes the error between the temperature reported by the Control Tool and that given by the calibrated thermometer. Event Generator The DC2227A is also equipped with a pushbutton to simulate events generated by IO-Link devices to inform IO-Link masters of requests that require special attention. Light barrier The light barrier offers many ways to interact with the device. It starts the device in COM3 mode if it is closed during power-up or in COM2 mode if left open. In IO-Link mode, its status is reported live on the PC control tool and in SIO mode its status is directly coupled to the CQ1 and Q2 drivers, thus allowing the user to operate the light bulb. Light bulb A 28V/100mA light bulb connects between Q2 and ground and serves to show the high current driving capability of the line drivers. It takes about 240ms to be turned on fully by the pulsing mechanism of the LT3669-2. To prevent data loss in IO-Link mode, driver Q2 is only enabled in between IO-Link telegrams. To turn it on and off from the control tool (in COM2 only) simply press the “Turn On” and “Turn Off” buttons within the light bulb section. In SIO mode, regardless on the IODD file chosen, the light bulb can be switched on and off by interacting with the light barrier. dc2227af DEMO MANUAL DC2227A additional information Connectors and Jumpers Jumper J3 The board has the following connectors: Jumper J3 enables/disables the on board LT3669-2 (which also generates the internal 3.3V supply rail). Close this jumper (default position) to use the onboard LT3669-2 as the IO-Link PHY (it will start up for L+ voltages above 14.8V). Leave this jumper open if the external DC1733A-B board is used (via the J4 connector) as the IO-Link PHY instead. Table 1. Connectors and Jumpers Overview Name Type Form Comment J1 Jumper Pin-2 Atmel µC Flash Erase J2 Connector M12 IO-Link Signals (L+, L–, CQ1, Q2) J3 Jumper Pin-2 LT3669-2 EN/UVLO Pin Header 8 × 2_2mm Eval Board DC1733 J4 J5 Connector Pin-6 SPI Interface J6 Jumper Pin-4 Sensor Selection J7 JTAG Header10 × 2 JTAG Programming J8 Jumper Pin-3 VDD3 Select J9 Jumper Pin-3 Reset Select Jumper J1 Connector J4 J4 is for connecting an external DC1733A-B demo circuit bypassing the on-board LT3669-2. This connection allows access to more signals from LT3669-2. Connect jumper J3 from DC1733A-B pin-to-pin to jumper J4 on this board. Table 3 identifies each pin. Jumper J1 sets the Erase/PB12 pin of the microcontroller to VDD3 (3.3V). By default the J1 header is not populated. For details about the Erase/PB12 pin see the ATSAM31S2AA microcontroller data sheet. Table 3. Connector J4 Pinout Pin Function Comment 1 TXD2 DC1733A-B Driver Input (Q2) 2 TXEN2 DC1733A-B Driver Input (Q2) 3 TXD1 DC1733A-B Driver Input (CQ1) Connector J2 4 TXEN1 DC1733A-B Driver Input (CQ1) Connector J2 is a 5-pin M12 male connector. Plug a standard industrial sensor cable to this connector to supply and communicate to the DC2227A using an IO-Link master. Table 2 shows the internal pin assignments to the LT3669-2 IO-Link PHY: 5 RXD1 DC1733A-B Receiver Output (CQ1) 6 GND DC1733A-B Ground 7 WAKEn DC1733A-B Wake-Up Output 8 GND DC1733A-B Ground Table 2. Connector J2 Pinout M12 Pin LT3669-2’s Pin Comment 1 L+ DC2227A Input Supply (24V) 2 Q2 LT3669-2 Second Driver 3 GND DC2227A Ground Node 4 CQ1 LT3669-2 Transceiver (IO-Link) 5 Not Connected 9 SC2n DC1733A-B Driver Short Circuit Output (Q2) 10 SC1n DC1733A-B Driver Short Circuit Output (CQ1) 11 GND DC1733A-B Ground 12 RST_n DC1733A-B POR Reset Output 13 VDD(EXT) DC1733A-B LDO’s Output (3.3V) 14 GND DC1733A-B Ground 15 TP33 DC1733A-B Buck Output (5V) 16 SYNC DC1733A-B Buck Oscillator Synchronization Input dc2227af 5 DEMO MANUAL DC2227A additional information Connector J5 Jumper J8 J5 is currently unused and may be helpful for the customer’s own applications that make use of the SPI interface of the Atmel microcontroller. J8 selects the source for the VDD3 power. Pin Description Comment Table 4. Connector J5 SPI Pinout 1 DC1733A-B’s LDO Close 1-2 to Use DC1733A-B as PHY Table 7. VDD3 Source Select Pinout Pin Function Comment 2 Local VDD3 rail Default: Connected to Pin 3 1 MISO Master In Slave Out 3 Local LT3669-2’s LDO Close 2-3 to Use Local LT3669-2 as PHY 2 MOSI Master Out Slave In 3 SPCK SPI Clock Jumper J9 4 RESETn Reset 5 VDD3 Power J9 selects the source for the microcontroller’s reset pin. 6 GND Ground Table 8. Reset Source Select Pinout Jumper J6 J6 configures the sense device used by the LTC2997 to measure temperature. It could be either the LTC2997’s internal diode, the on-board diode-connected NPN Q1 or a remote NPN (connected as a diode) using a twisted pair: Table 5. Jumper J6 Pinout (Temperature Sense Device) Pin Description Comment 1 DC1733A-B RSTn Close 1-2 to use DC1733A-B as PHY 2 Local RESETn Default: Connected to Pin 3 3 Local LT3669-2 RSTn Close 2-3 to Use Local LT3669-2 as PHY Indicators The following indicators are available: Pin Description Comment Table 9. Indicators 1 LTC2997’s VCC Close 1-2 to Use the LTC2997’s Int. NPN Name Comment 2 LTC2997’s D+ To Base/Collector of Remote NPN LED1 ON (Green) if Device Is Powered up ON (Red) if µC Started Successfully 3 Q1’s Base/Collector Close 2-3 to Use the On-board NPN Q1 LED2 4 LTC2997’s D– To Emitter of Remote NPN LED3 ON (Red) if Device Is in IO-Link Mode LP1 28V/100mA Light Bulb Between Q2 and GND Connector J7 Standard 20-pin JTAG programming/debugging interface. This interface fits many JTAG/ICE connectors. Table 6. JTAG Connector Pinout Pin Function 1, 2 VDD3 3 VDD3 5 TDI 7 TMS 9, 11 TCK 13 TDO 15 RESETn 17, 19 N.C. 6, 8, 10, 12, 14, 16, 18, 20 GND 6 TVS Protection The CQ1, Q2 and L+ pins are protected by 39V TVS diodes. Do not connect to any voltage higher than 36V. Comment Data Storage Via 100k Data Storage is not currently supported by DC2227A. Do not use pushbutton "DS upload" in Control Tool Software. IO-Link Firmware The firmware contained in the Atmel microcontroller is intellectual property owned by TEConcept GmbH in Germany. Any attempt to copy, transfer, or reverse engineer the firmware is forbidden. The source code or an object library for the IO-Link stack can be licensed from TEConcept. dc2227af DEMO MANUAL DC2227A additional information IO Device Description IODD File (COM2): TEConcept_GmbH-65538-<YYYYMMDD>-IODD1.1 Release Date: <YYYY-MM-DD> Document Version: V1.0 Device ID: 65538 Bit Rate: COM2 IO-Link Version: 1.1 MinCycleTime: 20ms IODD File (COM3): TEConcept_GmbH-65539-<YYYYMMDD>-IODD1.1 Release Date: <YYYY-MM-DD> Document Version: V1.0 Device ID: 65539 Bit Rate: COM3 IO-Link Version: 1.1 MinCycleTime: 800µs Device Basic Data: SIO Mode Supported: Yes Device: LTC DC2227A Vendor ID: 646 Vendor Name: TEConcept GmbH Vendor Text: www.teconcept.de/www.linear.com Description: TEConcept-LTC IO-Link DemoDeviceBoard V1.2 Process Data Name Description Datatype Bit Offset Optogatestate Temperature Bit Length Value Range State of Light Barrier Boolean 15 1 0 to 1 Temperature Measured Using the LTC2997 IntegerT 0 15 –32768 to 32767 Gradient Offset Unit 0.1 0 °C Events Code Name Type Mode 30480 Demo/Test Error Error Event Single Shot Description This Event Is Issued When the Demo Board Button Has Been Pressed. Also Used During the Conformance Tests dc2227af 7 DEMO MANUAL DC2227A additional information Variables Name Description Index Subindex Datatype Length Access Rights Default Value Range System Command Command Code Definition 2 00 UIntegerT 8 Bit wo Device Access Locks 12 00 RecordT 1 Bit rw Parameter (Write) Parameter Write Access Lock Access 12 01 BooleanT 1 Bit rw 0 0 or 1 Data Storage Lock Data Storage 12 02 BooleanT 1 Bit rw 0 0 or 1 Local Parameterization Lock Local parameterization 12 03 BooleanT 1 Bit rw 0 0 or 1 Local User Interface Lock Local User Interface Operation 12 04 BooleanT 1 Bit rw 0 0 or 1 Vendor Name Informative 16 00 StringT Max. 64 Byte ro TEConcept GmbH Vendor Text Additional Vendor Information 17 00 StringT Max. 64 Byte ro www.teconcept.de www.linear.com - Product Name Detailed Product or Type Name 18 00 StringT Max. 64 Byte ro LTC DC2227A - Product ID Product or type identification 19 00 StringT Max. 64 Byte ro TEC-LTC DC2227A - Product Text Description of Device function or Characteristic 00 StringT Max. 64 Byte ro TEC-LTC IO-Link DC2227A - Serial Number Vendor Specific SN 21 00 StringT Max. 16 Byte ro - Hardware Version Vendor Specific Format 22 00 StringT Max. 64 Byte ro 2.0 - Firmware Version Vendor Specific Format 23 00 StringT Max. 64 Byte ro 1.2.5 - Application Specific Tag Tag location or Tag Function Defined by User 24 00 StringT Max. 32 Byte rw Testing*********… Error Count Errors Since PowerOn or Reset 32 00 UIntegerT 16 Bit ro Standardized Device Locking Functions 20 Unit - - Light Bulb Light Bulb State 64 00 BooleanT 1 Bit rw 0 0 or 1 ADC Offset (in LSB) ADC Offset (in LSB) 65 00 IntegerT 8 Bit rw 0 –128 to 127 SC1 Counter Short Circuit Counter on CQ1 80 00 UIntegerT 16 Bit ro 0 0 to 65535 SC2 Counter Short Circuit Counter on Q2 81 00 UIntegerT 16 Bit ro 0 0 to 65535 Overtemp Counter Counts Overtemperature Events 82 00 UIntegerT 8 Bit ro 0 0 to 255 4mvK ADC Input Parameter for Temperature Measurement (LTC2997’s VPTAT) 90 00 UIntegerT 12 Bit rw 0 0 to 4095 LSB 1V8 ADC Input Parameter for Temperature Measurement (LTC2997’s VREF) 91 00 UIntegerT 12 Bit rw 0 0 to 4095 LSB 8 LSB dc2227af DEMO MANUAL DC2227A Parts List ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER CAP, X5R, 100nF, 10%, 10V, 0603 AVX, 0603ZD104KAT2A Required Circuit Components 1 6 C1, C2, C3, C4, C14, C16 2 3 C5, C8, C9 CAP, X5R, 4.7µF, 10%, 10V, 0805 MURATA, GRM21BR71A475KA73L 3 2 C6, C7 CAP, NP0, 18pF, 10%, 25V, 0603 AVX, 06033A180KAT2A 4 5 C10, C11, C12, C13, C22 CAP, X5R, 1µF, 10%, 10V, 0603 MURATA, GRM188R61A105KA61D 5 1 C15 CAP, X7R, 220nF, 10%, 10V, 0603 AVX, 0603ZC223KAT2A 6 1 C18 CAP, X5R, 22µF, 10%, 10V, 1206 MURATA, GRM31CR61A226KE19L 7 2 C24, C25 CAP, NP0, 470pF, 10%, 100V, 0603 TDK, C1608C0G2A471K080AA 8 1 C26 CAP, X7R, 10µF, 10%, 50V, 1206 MURATA, GRM31CR61H106KA12L 9 1 C33 CAP, X7R, 10pF, 10%, 10V, 0603 AVX, 0603ZC100KAT2A 10 1 D1 DIODE, SCHOTTKY, POWERDI123 DIODES INC., DFLS160-7-F 11 4 D2, D3, D4, D5 DIODE, TVS, SMB_2C VISHAY, SM6T39A 12 1 L1 IND, 10µH, 0.2A, 0805 TAIYO YUDEN, CB2012T100MRV 13 1 L2 IND, 33µH, 1A, SMD 6 × 6 SUMIDA, CDRH50D28RNP-330MC 14 1 R3 RES, 41.2k, 1%, 1/10W, 0603 VISHAY, CRCW060341K2FKEA 15 1 R4 RES, 10.2k, 1%, 1/10W, 0603 VISHAY, CRCW060310K2FKEA 16 1 R6 RES, 38.3k, 1%, 1/10W, 0603 VISHAY, CRCW060338K3FKEA 17 2 R16, R17 RES, 100k, 1%, 1/10W, 0603 VISHAY, CRCW0603100KFKEA 18 1 R12 RES, 84.5k, 1%, 1/10W, 0603 VISHAY, CRCW060384K5FKEA 19 1 R18 RES, 14k, 1%, 1/10W, 0603 VISHAY, CRCW060314K0FKEA 20 1 R20 RES, 4.42k, 1%, 1/10W, 0603 VISHAY, CRCW06034K42FKEA 21 2 R22, R55 RES, 10k, 1%, 1/10W, 0603 VISHAY, CRCW060310K0FKEA 22 2 R42, R43 RES, 4.7k, 1%, 1/10W, 0603 VISHAY, CRCW06034K70FKEA 23 1 R49 RES, 47k, 1%, 1/10W, 0603 VISHAY, CRCW060347K0FKEA 24 1 U1 IC, INDUSTRIAL TRANSCEIVER LINEAR TECH, LT3669HUFD-2#PBF 25 1 U3 IC, MICROCONTROLLER, QFN48 ATMEL, ATSAM3S2AA-MU 26 1 Y1 CRYSTAL, 14.7456 MHz, HC-49 SMD RALTRON, AS-14.7456-18SMDT CAP, X5R, 100nF, 10%, 10V, 0603 AVX, 0603ZD104KAT2A Temperature Sensor Specific Components 1 2 C20, C23 2 2 C19, C31 CAP, X5R, 1µF, 10%, 10V, 0603 MURATA, GRM188R61A105KA61D 3 1 C30 CAP, X7R, 470pF, 10%, 10V, 0603 AVX, 0603ZC471KAT2A 4 1 Q1 XSTR, NPN, 40V, SOT23 Fairchild, MMBT3904 5 1 R10 RES, 1k, 1%, 1/10W, 0603 VISHAY, CRCW06031K00FKEA 6 3 R14, R40, R54 RES, 100Ω, 1%, 1/10W, 0603 VISHAY, CRCW0603100RFKEA 7 1 U4 IC, TEMPERATURE SENSOR LINEAR TECH., LTC2997HDCB#PBF Light Barrier Specific Components 1 4 R50 RES, 4.7k, 1%, 1/10W, 0603 VISHAY, CRCW06034K70FKEA 2 1 R51 RES, 220Ω, 1%, 1/10W, 0603 VISHAY, CRCW0603220RFKEA 3 1 U302 XSTR, LIGHT SENSING SHARP, GP1S53VJ000F dc2227af 9 DEMO MANUAL DC2227A Parts List ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER Push-Buttom Specific Components 1 1 R53 RES, 4.7k, 1%, 1/10W, 0603 VISHAY, CRCW06034K70FKEA 2 1 SW1 SWITCH, PUSHBUTTON WÜRTH ELEKTRONIK, 430182050816 AVX, 0603ZD104KAT2A Additional Demo Board Circuit Components: 1 1 C21 CAP, X5R, 100nF, 10%, 10V, 0603 2 0 C17 OPTIONAL 3 0 C27, C28, C29, C32 OPTIONAL 4 0 C100 OPTIONAL 5 0 D6 OPTIONAL 6 1 D7 DIODE, SOT23 7 0 D8 OPTIONAL 8 1 LED1 LED, 0603D VISHAY, VLMTG1300-GS08 9 2 LED2, LED3 LED, 0603D KINGBRIGHT, KPG-1608SURKC-T 10 18 R1, R11, R13, R15, R23, R24, RES, 1k, 1%, 1/10W, 0603 R25, R27, R28, R29, R30, R31, R32, R33, R36, R37, R38, R39 VISHAY, CRCW06031K00FKEA 11 2 R2, R44 VISHAY, CRCW06030000Z0EA 12 8 R7, R19, R45, R46, R47, R48 RES, 100k, 1%, 1/10W, 0603 VISHAY, CRCW0603100KFKEA 13 2 R21, R26 RES, 10k 1%, 1/10W, 0603 VISHAY, CRCW060310K0FKEA 14 2 R34, R35 RES, 1.8k, 1%, 1/10W, 0603 VISHAY, CRCW06031K80FKEA 15 1 R41 RES, 88.7k, 1%, 1/10W, 0603 VISHAY, CRCW060388K7FKEA 16 0 R52 OPTIONAL 17 0 U2 OPTIONAL 18 0 Y2 OPTIONAL RES, 0Ω, 1%, 1/10W, 0603 DIODES INC., BAV199-7-F Hardware-For Demo Board Only: 1 0 J1 OPTIONAL 2 1 J3 HEADER, 1 × 2, 0.1" WÜRTH ELEKTRONIK, 61300211121 3 1 J2 CONNECTOR, M12, 5 PIN BINDER, 09-3441-500-05 4 1 J4 HEADER 2 × 8 2mm WÜRTH ELEKTRONIK, 62001621121 5 0 J5 OPTIONAL 6 1 J6 HEADER, 1 × 4, 0.1" WÜRTH ELEKTRONIK, 61300411121 7 1 J7 HEADER, 2 × 10, 0.1 " WÜRTH ELEKTRONIK, 61302021121 8 2 J8, J9 HEADER, 1x3, 0.1" WÜRTH ELEKTRONIK, 61300311121 9 5 J3, J6-J9 SHUNT, 0.1" WÜRTH ELEKTRONIK, 60900213421 10 1 LP1 SOCKET, LAMP SOCKET, WEDGE, T3 1/4 CML INNOVATIVE TECH., LH10 11 1 BULB, WEDGE, 28V, .1A, 1.6M JKL Components, 400 12 1 CABLE, 2M 4-WIRE UNSHIELDED BINDER, 79-5001-20-04 13 4 STANDOFF, 6-32 ALUM 3/8" DIGI-KEY, 3486K-ND 14 4 MACHINE SCREW, PAN PHILLIPS 6-32, 3/8" KEYSTONE, 9904 15 4 LOCK WASHER, #6 KEYSTONE, 4700 16 4 FLAT WASHER, #6, NYLON KEYSTONE, 3122 10 dc2227af A B C EN D1 DFLS160 10k R22 VDD3x R41 100k R17 VDD3 J9 4 3 1 2 SW1 Jumper2-3 TEConcept GmbH R32 Wentzingerstr. 21 0 2 4 6 8 10 12 14 16 LT3669HUFD-2 TXD2 TXEN2 TXD1 TXEN1 RXD1 1 2 3 4 D 79106 Freiburg Jumper J6 1 Q1 MMBT3904 0 tel.: +49-761 214436-0 2 FBout 38.3k CQ1 Q2 L+ 0 DNP D8 C24 470pF_100V L+ 10 9 11 DIO D2 SM6T39A 0 C17 DNP 50V 0 D+ U4 1uF Vref VDD3 www.teconcept.de 0 4 100R 100R C23 1V8ref TP34 TP35 Fiducial Fiducial LTC2997HDCB TEMP-Sensor 3 R54 6 R14 100R VPTAT R40 4mV/K 100nF D5 SM6T39A 1 2 3 4 5 J2 100k 2 0 7 6 VDD3 R21 10k 4mV/K VDD3 R15 1k LED1 0 VLMTG1300-GS08 LED green 0 0 D4 SM6T39A 0 0 0 C21 C20 0 RESETn TCK IN U2 R10 C100 0 TMS R46 100k 3 TDI R47 100k TP21 TP20 LED2 R34 1.8k 9 12 11 10 U3 R48 100k 1 TXEN2 1 1k JTAG J7 2 4 6 8 10 12 14 16 18 20 R39 R38 PA20/AD3 PA19/PGMD7/AD2 PA18/PGMD6/AD1 PA17/PGMD5/AD0 VDDOUT VDDIN PB3/AD7 PB2/AD6 PB1/AD5 PB0/AD4 GND2 1k 1 3 5 7 9 11 13 15 17 19 100nF ADVREF C14 KPG-1608SURKC-T KPG-1608SURKC-T LED red LED3 R35 1.8k 1k 8 7 6 5 4 3 2 1 0 C19 1uF SWITCH SR 1 TXEN1 0 1 TDO 1WAKEn R30 TP14 1 2 1V8ref 0 VDD3 TP10 0 OUT 1k 0 C8 4.7uF_X5R 0 0 R42 4.7k VDD3 VDD3 L1 10uH 2 48 Vpll SMD or THT Y1 1 TP2 14.7456MHz 2 C6 18pF TP3 C7 18pF VDD3 RESETn VDD18 0 1 2 3 4 5 6 J5 DNP TP22 TP23 0 R55 10k 2 0 VDD3 0 C28 DNP optional PP ATSAM3S2AA-MU TDI/PB4 PA6/PGMNOE PA5/PGMRDY PA4/PGMNCMD NRST TST PA3 PA2/PGMEN2 VDDIO33 GND34 PA1/PGMEN1 0 0 C9 4.7uF C2 100nF 0 0 C10 1uF C3 100nF 0 0 C11 1uF C4 100nF 0 0 49 0 R52 DNP LED R51 220R 1k R33 26 TDI R31 1k 25 R28 1k 1k 27 0 0 VDD3 1k 1k 28 29 30 1 TP13 31 32 33 R23 R13 35 34 R11 36 SCL R49 1 1 1 1 1 1 R50 4.7k 1 VDD3 Opto TP18 TP17 TP15 RESETn 47k TP11 TP9 TP5 TP6 C12 1uF C5 4.7uF U302 GP1S53VJ000F VDD3 TXD2 RXD2 C29 DNP SDA Opto SC2n SC1n enable internal Pullup: PA0, PA1, PA3 C1 100nF 1 TP24 TP25 TP26 TP27 TP28 TP29 0 TP30 TP31 Fiducial Fiducial Fiducial Fiducial Hole4mm Hole4mm Hole4mm Hole4mm C27 DNP VDD18 PA0/PGMEN0 VDD3 DNP Y2 TP32 LINEAR TECHNOLOGY HAS MADE A BEST EFFORT TO DESIGN A CIRCUIT THAT MEETS CUSTOMER SUPPLIED SPECIFICATIONS; HOWEVER, IT REMAINS THE CUSTOMERS RESPONSIBILITY TO VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL APPLICATION. COMPONENT SUBSTITUTION AND PRINTED CIRCUIT LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT PERFORMANCE OR RELIABILITY. Title CONTACT LINEAR TECHNOLOGY APPLICATIONS ENGINEERING FOR ASSISTANCE. Size THIS CIRCUIT IS PROPRIETARY TO A3 LINEAR TECHNOLOGY AND SUPPLIED FOR USE WITH LINEAR TECHNOLOGY PARTS. Date: CUSTOMER NOTICE 0 R43 4.7k VDD18 R1 1k J1 1 DNP 2 VDD3 1 Optional_Tantal_A VDD18 100nF 100nF DNP 1 TP16 TP8 R44 0R R45 100k VDD3 Binder_09-3441-500-05 R19 1 D7 BAV199 VDD3 C26 10uF_50V_X7R 0 0 D3 SM6T39A 0 0 C22 1uF VDD3x 0 C18 22uF_X5R C25 470pF_100V TP T P12 10k 0 1 12 EN R26 14k 3.28V 41.2k R18 4.42k 0 R4 10.2k R3 R20 FBldo R12 84.5k 13 DIO 23 20 19 26 R6 22RT C16 100nF 27 CPOR 21 C32 DNP 1 0 Orbitec_OR1206_BA9 LP1 ground terminal should 2 0 be the external case of light bulb socket! 28V100mA C31 1 1 C30 470p 0 Q2 SYNC SC1n RST_n TXEN2 TXEN1 0 CQ1 Q2 L+ EN/UVLO DIO AGND FBLDO LDO ILIM RT CPOR FBout DJ6: Jumper 1-2 internal LTC2997 Sensor selected Jumper 2-3 Sensor Q1 selected ext. Diode wired to Pin 2 and Pin 4, no Jumper RESETn RST_n 5 J4 8 7 6 5 4 WAKEn SC2n SC1n RSTn SR SYNC DA SW BST LDOin BD 1 TP33 5V not needed HEADER 2X8 2MM to demoboard DC1733 1k R29 L+ 1k 1k R27 1k R25 3 WAKEn 1k 2 R24 1 SC2n 1 3 5 7 9 11 13 15 28 SR 25 SYNC 24 DA 14 SW 15 BST 16 18 17 SC1n C33 10pF TP T P4 TXD2 TXD1 RXD1 WAKEn SC2n Jumper2-3 RSTn J8 J3 Jumper RSTn CPOR 88.7k TXD2 TXEN2 TXD1 TXEN1 RXD1 100k R16 RSTn 100k 1uF C13 C15 220nF_X7R 0 FSM4JSMA TE CONNECTIVITY / ALCOSWITCH SWITCH R53 4.7k VDD3 VDD3 0 R7 1 R2 0R U1 D6 DNP 47 LDOin 3 1 2 1 GND29 29 1 GND 3 46 VDDIO47 14 XIN/PB9/PGMCK PA16/PGMD4 15 VDDPLL 1D+ PA15/PGMD3 45 XOUT/PB8 16 SPCK VDDIO13 13 1D- PA14/PGMD2 44 DDP/PB11 17 MOSI PA13/PGMD1 43 D 3 2 1 3 2 1 2 MISO DDM/PB10 18 42 19 ERASE/PB12 LED 1 TP19 VDDCORE TCK 40 PA12/PGMD0 41 VDDCORE41 PA11/PGMM3 20 TCK/SWCLK/PB7 PA10/PGMM2 21 1k TXD1 R36 1 TDO 37 TDO/TRACESWO/PB5 TMS 39 TMS/SWDIO/PB6 PA9/PGMM1 22 1k RXD1R37 1 38 JTAGSEL PA8/XOUT32/PGMM0 23 PA7/XIN32/PGMNVALID 24 Wednesday, November 05, 2014 1 Sheet LTC CONFIDENTIAL FOR CUSTOMER USE ONLY LT3669 DEMO CIRCUIT DC2227A 1 0 1 0 1 VDD18 1 3 1 2 TP1 1 2 3 2 4 VCC PP GND 7 5 3 4 L2 CDRH50D28RNP-330MC 1 1 of 8 Rev 1.1 1630 McCarthy Blvd. Milpitas, CA 95035 Phone: (408) 432-1900 Fax: (408) 434-0507 www.linear.com 1 4 1 1 Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 1 5 A B C D DEMO MANUAL DC2227A Schematic Diagram dc2227af 11 DEMO MANUAL DC2227A DEMONSTRATION BOARD IMPORTANT NOTICE Linear Technology Corporation (LTC) provides the enclosed product(s) under the following AS IS conditions: This demonstration board (DEMO BOARD) kit being sold or provided by Linear Technology is intended for use for ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY and is not provided by LTC for commercial use. As such, the DEMO BOARD herein may not be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including but not limited to product safety measures typically found in finished commercial goods. As a prototype, this product does not fall within the scope of the European Union directive on electromagnetic compatibility and therefore may or may not meet the technical requirements of the directive, or other regulations. If this evaluation kit does not meet the specifications recited in the DEMO BOARD manual the kit may be returned within 30 days from the date of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY THE SELLER TO BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THIS INDEMNITY, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user releases LTC from all claims arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to take any and all appropriate precautions with regard to electrostatic discharge. Also be aware that the products herein may not be regulatory compliant or agency certified (FCC, UL, CE, etc.). No License is granted under any patent right or other intellectual property whatsoever. LTC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or any other intellectual property rights of any kind. LTC currently services a variety of customers for products around the world, and therefore this transaction is not exclusive. Please read the DEMO BOARD manual prior to handling the product. Persons handling this product must have electronics training and observe good laboratory practice standards. Common sense is encouraged. This notice contains important safety information about temperatures and voltages. For further safety concerns, please contact a LTC application engineer. Mailing Address: Linear Technology 1630 McCarthy Blvd. Milpitas, CA 95035 Copyright © 2004, Linear Technology Corporation 12 Linear Technology Corporation dc2227af LT 0415 • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com LINEAR TECHNOLOGY CORPORATION 2015