LPC1311/13/42/43
32-bit ARM Cortex-M3 microcontroller; up to 32 kB flash and
8 kB SRAM; USB device
Rev. 4 — 20 June 2011
Product data sheet
1. General description
The LPC1311/13/42/43 are ARM Cortex-M3 based microcontrollers for embedded
applications featuring a high level of integration and low power consumption. The ARM
Cortex-M3 is a next generation core that offers system enhancements such as enhanced
debug features and a higher level of support block integration.
The LPC1311/13/42/43 operate at CPU frequencies of up to 72 MHz. The ARM
Cortex-M3 CPU incorporates a 3-stage pipeline and uses a Harvard architecture with
separate local instruction and data buses as well as a third bus for peripherals. The ARM
Cortex-M3 CPU also includes an internal prefetch unit that supports speculative
branching.
The peripheral complement of the LPC1311/13/42/43 includes up to 32 kB of flash
memory, up to 8 kB of data memory, USB Device (LPC1342/43 only), one Fast-mode Plus
I2C-bus interface, one UART, four general purpose timers, and up to 42 general purpose
I/O pins.
Remark: The LPC1311/13/42/43 series consists of the LPC1300 series (parts
LPC1311/13/42/43) and the LPC1300L series (parts LPC1311/01 and LPC1313/01). The
LPC1300L series features the following enhancements over the LPC1300 series:
•
•
•
•
•
•
Power profiles with lower power consumption in Active and Sleep modes.
Four levels for BOD forced reset.
Second SSP controller (LPC1313FBD48/01 only).
Windowed Watchdog Timer (WWDT).
Internal pull-up resistors pull up pins to full VDD level.
Programmable pseudo open-drain mode for GPIO pins.
2. Features and benefits
ARM Cortex-M3 processor, running at frequencies of up to 72 MHz.
ARM Cortex-M3 built-in Nested Vectored Interrupt Controller (NVIC).
32 kB (LPC1343/13)/16 kB (LPC1342)/8 kB (LPC1311) on-chip flash programming
memory.
8 kB (LPC1343/13)/4 kB (LPC1342/11) SRAM.
In-System Programming (ISP) and In-Application Programming (IAP) via on-chip
bootloader software.
Selectable boot-up: UART or USB (USB on LPC1342/43 only).
On LPC1342/43: USB MSC and HID on-chip drivers.
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
Serial interfaces:
USB 2.0 full-speed device controller with on-chip PHY for device (LPC1342/43
only).
UART with fractional baud rate generation, modem, internal FIFO, and
RS-485/EIA-485 support.
SSP controller with FIFO and multi-protocol capabilities.
Additional SSP controller on LPC1313FBD48/01.
I2C-bus interface supporting full I2C-bus specification and Fast-mode Plus with a
data rate of 1 Mbit/s with multiple address recognition and monitor mode.
Other peripherals:
Up to 42 General Purpose I/O (GPIO) pins with configurable pull-up/pull-down
resistors.
Four general purpose counter/timers with a total of four capture inputs and 13
match outputs.
Programmable WatchDog Timer (WDT).
Programmable Windowed Watchdog Timer (WWDT) on LPC1311/01 and
LPC1313/01.
System tick timer.
Serial Wire Debug and Serial Wire Trace port.
High-current output driver (20 mA) on one pin.
High-current sink drivers (20 mA) on two I2C-bus pins in Fast-mode Plus.
Integrated PMU (Power Management Unit) to minimize power consumption during
Sleep, Deep-sleep, and Deep power-down modes.
Power profiles residing in boot ROM allowing to optimize performance and minimize
power consumption for any given application through one simple function call.
(LPC1300L series, on LPC1311/01 and LPC1313/01 only.)
Three reduced power modes: Sleep, Deep-sleep, and Deep power-down.
Single power supply (2.0 V to 3.6 V).
10-bit ADC with input multiplexing among 8 pins.
GPIO pins can be used as edge and level sensitive interrupt sources.
Clock output function with divider that can reflect the system oscillator clock, IRC
clock, CPU clock, or the watchdog clock.
Processor wake-up from Deep-sleep mode via a dedicated start logic using up to 40 of
the functional pins.
Brownout detect with four separate thresholds for interrupt and one threshold for
forced reset (four thresholds for forced reset on the LPC1311/01 and LPC1313/01
parts).
Power-On Reset (POR).
Integrated oscillator with an operating range of 1 MHz to 25 MHz.
12 MHz internal RC oscillator trimmed to 1 % accuracy over the entire temperature
and voltage range that can optionally be used as a system clock.
Programmable watchdog oscillator with a frequency range of 7.8 kHz to 1.8 MHz.
System PLL allows CPU operation up to the maximum CPU rate without the need for a
high-frequency crystal. May be run from the system oscillator or the internal RC
oscillator.
For USB (LPC1342/43), a second, dedicated PLL is provided.
Code Read Protection (CRP) with different security levels.
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
2 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
Unique device serial number for identification.
Available as 48-pin LQFP package and 33-pin HVQFN package.
3. Applications
eMetering
Lighting
Alarm systems
White goods
4. Ordering information
Table 1.
Ordering information
Type number
Package
Name
Description
Version
LPC1311FHN33
HVQFN33
HVQFN33: plastic thermal enhanced very thin quad flat package; no
leads; 33 terminals; body 7 7 0.85 mm
n/a
LPC1311FHN33/01
HVQFN33
HVQFN33: plastic thermal enhanced very thin quad flat package; no
leads; 33 terminals; body 7 7 0.85 mm
n/a
LPC1313FHN33
HVQFN33
HVQFN33: plastic thermal enhanced very thin quad flat package; no
leads; 33 terminals; body 7 7 0.85 mm
n/a
LPC1313FHN33/01
HVQFN33
HVQFN33: plastic thermal enhanced very thin quad flat package; no
leads; 33 terminals; body 7 7 0.85 mm
n/a
LPC1313FBD48
LQFP48
LQFP48: plastic low profile quad flat package; 48 leads; body 7 7
1.4 mm
SOT313-2
LPC1313FBD48/01
LQFP48
LQFP48: plastic low profile quad flat package; 48 leads; body 7 7
1.4 mm
SOT313-2
LPC1342FHN33
HVQFN33
HVQFN33: plastic thermal enhanced very thin quad flat package; no
leads; 33 terminals; body 7 7 0.85 mm
n/a
LPC1342FBD48
LQFP48
LQFP48: plastic low profile quad flat package; 48 leads; body 7 7
1.4 mm
SOT313-2
LPC1343FHN33
HVQFN33
HVQFN33: plastic thermal enhanced very thin quad flat package; no
leads; 33 terminals; body 7 7 0.85 mm
n/a
LPC1343FBD48
LQFP48
LQFP48: plastic low profile quad flat package; 48 leads; body 7 7
1.4 mm
SOT313-2
4.1 Ordering options
Table 2.
Ordering options for LPC1311/13/42/43
Type number
Flash
Total
SRAM
USB
Power
profiles
UART
RS-485
I2C/
Fast+
SSP ADC
Pins
channels
Package
LPC1311FHN33
8 kB
4 kB
-
no
1
1
1
8
33
HVQFN33
LPC1311FHN33/01
8 kB
4 kB
-
yes
1
1
1
8
33
HVQFN33
LPC1313FHN33
32 kB
8 kB
-
no
1
1
1
8
33
HVQFN33
LPC1313FHN33/01
32 kB
8 kB
-
yes
1
1
1
8
33
HVQFN33
LPC1313FBD48
32 kB
8 kB
-
no
1
1
1
8
48
LQFP48
LPC1313FBD48/01
32 kB
8 kB
-
yes
1
1
2
8
48
LQFP48
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
3 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
Table 2.
Ordering options for LPC1311/13/42/43 …continued
Type number
Flash
Total
SRAM
USB
Power
profiles
UART
RS-485
I2C/
Fast+
SSP ADC
Pins
channels
Package
LPC1342FHN33
16 kB
4 kB
Device
no
1
1
1
8
33
HVQFN33
LPC1342FBD48
16 kB
4 kB
Device
no
1
1
1
8
48
LQFP48
LPC1343FHN33
32 kB
8 kB
Device
no
1
1
1
8
33
HVQFN33
LPC1343FBD48
32 kB
8 kB
Device
no
1
1
1
8
48
LQFP48
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
4 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
5. Block diagram
XTALIN
XTALOUT
RESET
USB pins
SWD
LPC1311/13/42/43
USB PHY(1)
TEST/DEBUG
INTERFACE
IRC
CLOCK
GENERATION,
POWER CONTROL,
SYSTEM
FUNCTIONS
WDO
ARM
CORTEX-M3
I-code
bus
D-code
bus
USB DEVICE
CONTROLLER(1)
system
bus
POR
CLKOUT
clocks and
controls
slave
slave
ROM
AHB-LITE BUS
GPIO ports
PIO0/1/2/3
slave
HIGH-SPEED
GPIO
RXD
TXD
CT32B0_CAP0
CT32B1_MAT[3:0]
CT32B1_CAP0
CT16B0_MAT[2:0]
CT16B0_CAP0
CT16B1_MAT[1:0]
CT16B1_CAP0
SRAM
4/8 kB
slave
slave
FLASH
8/16/32 kB
AHB TO
APB
BRIDGE
UART
DTR, DSR(2), CTS,
DCD(2), RI(2), RTS
CT32B0_MAT[3:0]
slave
AD[7:0]
10-bit ADC
SSP0
SCK0,SSEL0
MISO0, MOSI0
SSP1(3)
SCK1,SSEL1
MISO1, MOSI0
I2C-BUS
SCL
SDA
32-bit COUNTER/TIMER 0
32-bit COUNTER/TIMER 1
16-bit COUNTER/TIMER 0
WDT/WWDT(4)
16-bit COUNTER/TIMER 1
IOCONFIG
SYSTEM CONTROL
002aae722
(1) LPC1342/43 only.
(2) LQFP48 package only.
(3) On LPC1313FBD48/01 only.
(4) Windowed WatchDog Timer (WWDT) on LPC1311/01 and LPC1313/01 only.
Fig 1.
Block diagram
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
5 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
6. Pinning information
37 PIO3_1
38 PIO2_3/RI
39 SWDIO/PIO1_3/AD4/CT32B1_MAT2
40 PIO1_4/AD5/CT32B1_MAT3/WAKEUP
41 VSS
42 PIO1_11/AD7
44 VDD
43 PIO3_2
45 PIO1_5/RTS/CT32B0_CAP0
46 PIO1_6/RXD/CT32B0_MAT0
47 PIO1_7/TXD/CT32B0_MAT1
48 PIO3_3
6.1 Pinning
PIO2_6
1
36 PIO3_0
PIO2_0/DTR
2
35 R/PIO1_2/AD3/CT32B1_MAT1
RESET/PIO0_0
3
34 R/PIO1_1/AD2/CT32B1_MAT0
PIO0_1/CLKOUT/CT32B0_MAT2/USB_FTOGGLE
4
33 R/PIO1_0/AD1/CT32B1_CAP0
VSS
5
32 R/PIO0_11/AD0/CT32B0_MAT3
XTALIN
6
XTALOUT
7
VDD
8
29 SWCLK/PIO0_10/SCK0/CT16B0_MAT2
PIO1_8/CT16B1_CAP0
9
28 PIO0_9/MOSI0/CT16B0_MAT1/SWO
31 PIO2_11/SCK0
LPC1342FBD48
LPC1343FBD48
30 PIO1_10/AD6/CT16B1_MAT1
PIO0_2/SSEL0/CT16B0_CAP0 10
27 PIO0_8/MISO0/CT16B0_MAT0
Fig 2.
PIO2_9 24
PIO0_7/CTS 23
PIO0_6/USB_CONNECT/SCK 22
PIO2_5 21
USB_DP 20
USB_DM 19
PIO2_4 18
PIO1_9/CT16B1_MAT0 17
PIO0_5/SDA 16
PIO0_4/SCL 15
25 PIO2_10
PIO2_1/DSR 13
26 PIO2_2/DCD
PIO2_8 12
PIO0_3/USB_VBUS 14
PIO2_7 11
002aae505
LPC1342/43 LQFP48 package
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
6 of 73
LPC1311/13/42/43
NXP Semiconductors
PIO1_7/TXD/CT32B0_MAT1
PIO1_6/RXD/CT32B0_MAT0
PIO1_5/RTS/CT32B0_CAP0
VDD
PIO3_2
PIO1_11/AD7
PIO1_4/AD5/CT32B1_MAT3/WAKEUP
SWDIO/PIO1_3/AD4/CT32B1_MAT2
31
30
29
28
27
26
25
terminal 1
index area
32
32-bit ARM Cortex-M3 microcontroller
PIO2_0/DTR
1
24
R/PIO1_2/AD3/CT32B1_MAT1
RESET/PIO0_0
2
23
R/PIO1_1/AD2/CT32B1_MAT0
PIO0_1/CLKOUT/CT32B0_MAT2/USB_FTOGGLE
3
22
R/PIO1_0/AD1/CT32B1_CAP0
XTALIN
4
21
R/PIO0_11/AD0/CT32B0_MAT3
XTALOUT
5
20
PIO1_10/AD6/CT16B1_MAT1
VDD
6
19
SWCLK/PIO0_10/SCK0/CT16B0_MAT2
PIO1_8/CT16B1_CAP0
7
18
PIO0_9/MOSI0/CT16B0_MAT1/SWO
PIO0_2/SSEL0/CT16B0_CAP0
8
17
PIO0_8/MISO0/CT16B0_MAT0
LPC1342FHN33
LPC1343FHN33
9
10
11
12
13
14
15
16
PIO0_3/USB_VBUS
PIO0_4/SCL
PIO0_5/SDA
PIO1_9/CT16B1_MAT0
USB_DM
USB_DP
PIO0_6/USB_CONNECT/SCK0
PIO0_7/CTS
33 VSS
002aae516
Transparent top view
Fig 3.
LPC1342/43 HVQFN33 package
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
7 of 73
LPC1311/13/42/43
NXP Semiconductors
37 PIO3_1
38 PIO2_3/RI/MOSI1(1)
39 SWDIO/PIO1_3/AD4/CT32B1_MAT2
41 VSS
40 PIO1_4/AD5/CT32B1_MAT3/WAKEUP
42 PIO1_11/AD7
43 PIO3_2
44 VDD
45 PIO1_5/RTS/CT32B0_CAP0
46 PIO1_6/RXD/CT32B0_MAT0
47 PIO1_7/TXD/CT32B0_MAT1
48 PIO3_3
32-bit ARM Cortex-M3 microcontroller
PIO2_6
1
36 PIO3_0
PIO2_0/DTR/SSEL1(1)
2
35 R/PIO1_2/AD3/CT32B1_MAT1
RESET/PIO0_0
3
34 R/PIO1_1/AD2/CT32B1_MAT0
PIO0_1/CLKOUT/CT32B0_MAT2
4
33 R/PIO1_0/AD1/CT32B1_CAP0
VSS
5
XTALIN
6
XTALOUT
7
VDD
8
29 SWCLK/PIO0_10/SCK0/CT16B0_MAT2
PIO1_8/CT16B1_CAP0
9
28 PIO0_9/MOSI0/CT16B0_MAT1/SWO
32 R/PIO0_11/AD0/CT32B0_MAT3
LPC1313FBD48
LPC1313FBD48/01
31 PIO2_11/SCK0
30 PIO1_10/AD6/CT16B1_MAT1
PIO0_2/SSEL0/CT16B0_CAP0 10
27 PIO0_8/MISO0/CT16B0_MAT0
PIO2_9 24
PIO0_7/CTS 23
PIO0_6/SCK0 22
PIO3_5 21
PIO2_5 20
PIO2_4 19
PIO3_4 18
PIO1_9/CT16B1_MAT0 17
PIO0_5/SDA 16
25 PIO2_10
PIO0_4/SCL 15
PIO2_8 12
PIO0_3 14
26 PIO2_2/DCD/MISO1(1)
PIO2_1/DSR/SCK1(1) 13
PIO2_7 11
002aae513
(1) SSP1 or UART function on LPC1313FBD48/01 only.
Fig 4.
LPC1313 LQFP48 package
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
8 of 73
LPC1311/13/42/43
NXP Semiconductors
VDD
PIO3_2
PIO1_11/AD7
PIO1_4/AD5/CT32B1_MAT3/WAKEUP
SWDIO/PIO1_3/AD4/CT32B1_MAT2
27
26
25
PIO1_5/RTS/CT32B0_CAP0
28
PIO1_6/RXD/CT32B0_MAT0
30
29
PIO1_7/TXD/CT32B0_MAT1
31
terminal 1
index area
32
32-bit ARM Cortex-M3 microcontroller
7
33 VSS
18
PIO0_9/MOSI0/CT16B0_MAT1/SWO
PIO0_2/SSEL0/CT16B0_CAP0
8
17
PIO0_8/MISO0/CT16B0_MAT0
16
SWCLK/PIO0_10/SCK0/CT16B0_MAT2
PIO1_8/CT16B1_CAP0
PIO0_7/CTS
19
15
6
14
PIO1_10/AD6/CT16B1_MAT1
VDD
PIO3_5
20
PIO0_6/SCK0
5
13
R/PIO0_11/AD0/CT32B0_MAT3
XTALOUT
PIO3_4
21
12
R/PIO1_0/AD1/CT32B1_CAP0
4
PIO1_9/CT16B1_MAT0
22
XTALIN
LPC1311FHN33
LPC1311FHN33/01
LPC1313FHN33
LPC1313FHN33/01
11
3
PIO0_5/SDA
R/PIO1_1/AD2/CT32B1_MAT0
PIO0_1/CLKOUT/CT32B0_MAT2
9
R/PIO1_2/AD3/CT32B1_MAT1
23
10
24
2
PIO0_3
1
PIO0_4/SCL
PIO2_0/DTR
RESET/PIO0_0
002aae517
Transparent top view
Fig 5.
LPC1311_13_42_43
Product data sheet
LPC1311/13 HVQFN33 package
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
9 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
6.2 Pin description
Table 3.
LPC1313/42/43 LQFP48 pin description table
Symbol
RESET/PIO0_0
PIO0_1/CLKOUT/
CT32B0_MAT2/
USB_FTOGGLE
Pin
3[2]
4[3]
Start
logic
input
Type Reset Description
state
yes
I
I; PU
RESET — External reset input with 20 ns glitch filter. A LOW-going
pulse as short as 50 ns on this pin resets the device, causing I/O
ports and peripherals to take on their default states, and processor
execution to begin at address 0.
I/O
-
PIO0_0 — General purpose digital input/output pin with 10 ns glitch
filter.
I/O
I; PU
PIO0_1 — General purpose digital input/output pin. A LOW level on
this pin during reset starts the ISP command handler or the USB
device enumeration (USB on LPC1342/43 only, see description of
PIO0_3).
O
-
CLKOUT — Clockout pin.
O
-
CT32B0_MAT2 — Match output 2 for 32-bit timer 0.
O
-
USB_FTOGGLE — USB 1 ms Start-of-Frame signal (LPC1342/43
only).
I/O
I; PU
PIO0_2 — General purpose digital input/output pin.
I/O
-
SSEL0 — Slave select for SSP0.
I
-
CT16B0_CAP0 — Capture input 0 for 16-bit timer 0.
I/O
I; PU
PIO0_3 — General purpose digital input/output pin. LPC1342/43
only: A LOW level on this pin during reset starts the ISP command
handler, a HIGH level starts the USB device enumeration.
I
-
USB_VBUS — Monitors the presence of USB bus power
(LPC1342/43 only).
I/O
I; IA
PIO0_4 — General purpose digital input/output pin (open-drain).
I/O
-
SCL — I2C-bus clock input/output (open-drain). High-current sink
only if I2C Fast-mode Plus is selected in the I/O configuration
register.
I/O
I; IA
PIO0_5 — General purpose digital input/output pin (open-drain).
I/O
-
SDA — I2C-bus data input/output (open-drain). High-current sink
only if I2C Fast-mode Plus is selected in the I/O configuration
register.
I/O
I; PU
PIO0_6 — General purpose digital input/output pin.
O
-
USB_CONNECT — Signal used to switch an external 1.5 k
resistor under software control. Used with the SoftConnect USB
feature (LPC1342/43 only).
I/O
-
SCK0 — Serial clock for SSP0.
I/O
I; PU
PIO0_7 — General purpose digital input/output pin (high-current
output driver).
I
-
CTS — Clear To Send input for UART.
I/O
I; PU
PIO0_8 — General purpose digital input/output pin.
I/O
-
MISO0 — Master In Slave Out for SSP0.
O
-
CT16B0_MAT0 — Match output 0 for 16-bit timer 0.
yes
PIO0_2/SSEL0/
CT16B0_CAP0
10[3] yes
PIO0_3/USB_VBUS
14[3] yes
PIO0_4/SCL
PIO0_5/SDA
15[4] yes
16[4] yes
PIO0_6/
USB_CONNECT/
SCK0
22[3] yes
PIO0_7/CTS
23[3]
PIO0_8/MISO0/
CT16B0_MAT0
27[3]
LPC1311_13_42_43
Product data sheet
yes
yes
[1]
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
10 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
Table 3.
LPC1313/42/43 LQFP48 pin description table …continued
Symbol
Pin
Start
logic
input
PIO0_9/MOSI0/
CT16B0_MAT1/
SWO
28[3] yes
SWCLK/PIO0_10/
SCK0/CT16B0_MAT2
29[3]
R/PIO0_11/
AD0/CT32B0_MAT3
R/PIO1_0/
AD1/CT32B1_CAP0
R/PIO1_1/
AD2/CT32B1_MAT0
R/PIO1_2/
AD3/CT32B1_MAT1
32[5]
33[5]
35[5]
SWDIO/PIO1_3/
AD4/
CT32B1_MAT2
PIO1_4/AD5/
CT32B1_MAT3/
WAKEUP
40[5]
Product data sheet
yes
yes
34[5] yes
39[5]
LPC1311_13_42_43
yes
yes
yes
yes
Type Reset Description
state
[1]
I/O
I; PU
PIO0_9 — General purpose digital input/output pin.
I/O
-
MOSI0 — Master Out Slave In for SSP0.
O
-
CT16B0_MAT1 — Match output 1 for 16-bit timer 0.
O
-
SWO — Serial wire trace output.
I
I; PU
SWCLK — Serial wire clock.
I/O
-
PIO0_10 — General purpose digital input/output pin.
I/O
-
SCK0 — Serial clock for SSP0.
O
-
CT16B0_MAT2 — Match output 2 for 16-bit timer 0.
-
I; PU
R — Reserved. Configure for an alternate function in the IOCONFIG
block.
I/O
-
PIO0_11 — General purpose digital input/output pin.
I
-
AD0 — A/D converter, input 0.
O
-
CT32B0_MAT3 — Match output 3 for 32-bit timer 0.
-
I; PU
R — Reserved. Configure for an alternate function in the IOCONFIG
block.
I/O
-
PIO1_0 — General purpose digital input/output pin.
I
-
AD1 — A/D converter, input 1.
I
-
CT32B1_CAP0 — Capture input 0 for 32-bit timer 1.
-
I; PU
R — Reserved. Configure for an alternate function in the IOCONFIG
block.
I/O
-
PIO1_1 — General purpose digital input/output pin.
I
-
AD2 — A/D converter, input 2.
O
-
CT32B1_MAT0 — Match output 0 for 32-bit timer 1.
-
I; PU
R — Reserved. Configure for an alternate function in the IOCONFIG
block.
I/O
-
PIO1_2 — General purpose digital input/output pin.
I
-
AD3 — A/D converter, input 3.
O
-
CT32B1_MAT1 — Match output 1 for 32-bit timer 1.
I/O
I; PU
SWDIO — Serial wire debug input/output.
I/O
-
PIO1_3 — General purpose digital input/output pin.
I
-
AD4 — A/D converter, input 4.
O
-
CT32B1_MAT2 — Match output 2 for 32-bit timer 1.
I/O
I; PU
PIO1_4 — General purpose digital input/output pin.
I
-
AD5 — A/D converter, input 5.
O
-
CT32B1_MAT3 — Match output 3 for 32-bit timer 1.
I
-
WAKEUP — Deep power-down mode wake-up pin with 20 ns glitch
filter. This pin must be pulled HIGH externally to enter Deep
power-down mode and pulled LOW to exit Deep power-down mode.
A LOW-going pulse as short as 50 ns wakes up the part.
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
11 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
Table 3.
LPC1313/42/43 LQFP48 pin description table …continued
Symbol
PIO1_5/RTS/
CT32B0_CAP0
Pin
Start
logic
input
45[3] yes
PIO1_6/RXD/
CT32B0_MAT0
46[3] yes
PIO1_7/TXD/
CT32B0_MAT1
47[3] yes
PIO1_8/CT16B1_CAP0
9[3]
yes
PIO1_9/CT16B1_MAT0
17[3]
PIO1_10/AD6/
CT16B1_MAT1
30[5]
PIO1_11/AD7
42[5]
yes
PIO2_0/DTR/SSEL1
2[3]
yes
PIO2_1/DSR/SCK1
PIO2_2/DCD/MISO1
PIO2_3/RI/MOSI1
13[3]
26[3]
yes
yes
yes
yes
38[3] yes
Type Reset Description
state
[1]
I/O
I; PU
PIO1_5 — General purpose digital input/output pin.
O
-
RTS — Request To Send output for UART.
I
-
CT32B0_CAP0 — Capture input 0 for 32-bit timer 0.
I/O
I; PU
PIO1_6 — General purpose digital input/output pin.
I
-
RXD — Receiver input for UART.
O
-
CT32B0_MAT0 — Match output 0 for 32-bit timer 0.
I/O
I; PU
PIO1_7 — General purpose digital input/output pin.
O
-
TXD — Transmitter output for UART.
O
-
CT32B0_MAT1 — Match output 1 for 32-bit timer 0.
I/O
I; PU
PIO1_8 — General purpose digital input/output pin.
I
-
CT16B1_CAP0 — Capture input 0 for 16-bit timer 1.
I/O
I; PU
PIO1_9 — General purpose digital input/output pin.
O
-
CT16B1_MAT0 — Match output 0 for 16-bit timer 1.
I/O
I; PU
PIO1_10 — General purpose digital input/output pin.
I
-
AD6 — A/D converter, input 6.
O
-
CT16B1_MAT1 — Match output 1 for 16-bit timer 1.
I/O
I; PU
PIO1_11 — General purpose digital input/output pin.
I
-
AD7 — A/D converter, input 7.
I/O
I; PU
PIO2_0 — General purpose digital input/output pin.
O
-
DTR — Data Terminal Ready output for UART.
I/O
-
SSEL1 — Slave Select for SSP1 (LPC1313FBD48/01 only).
I/O
I; PU
PIO2_1 — General purpose digital input/output pin.
I
-
DSR — Data Set Ready input for UART.
I/O
-
SCK1 — Serial clock for SSP1 (LPC1313FBD48/01 only).
I/O
I; PU
PIO2_2 — General purpose digital input/output pin.
I
-
DCD — Data Carrier Detect input for UART.
I/O
-
MISO1 — Master In Slave Out for SSP1 (LPC1313FBD48/01 only).
I/O
I; PU
PIO2_3 — General purpose digital input/output pin.
I
-
RI — Ring Indicator input for UART.
I/O
-
MOSI1 — Master Out Slave In for SSP1 (LPC1313FBD48/01 only).
PIO2_4
18[3] yes
I/O
I; PU
PIO2_4 — General purpose digital input/output pin (LPC1342/43
only).
PIO2_4
19[3] yes
I/O
I; PU
PIO2_4 — General purpose digital input/output pin (LPC1313 only).
PIO2_5
21[3]
yes
I/O
I; PU
PIO2_5 — General purpose digital input/output pin (LPC1342/43
only).
PIO2_5
20[3] yes
I/O
I; PU
PIO2_5 — General purpose digital input/output pin (LPC1313 only).
PIO2_6
1[3]
yes
I/O
I; PU
PIO2_6 — General purpose digital input/output pin.
PIO2_7
11[3]
yes
I/O
I; PU
PIO2_7 — General purpose digital input/output pin.
PIO2_8
12[3] yes
I/O
I; PU
PIO2_8 — General purpose digital input/output pin.
PIO2_9
24[3]
I/O
I; PU
PIO2_9 — General purpose digital input/output pin.
LPC1311_13_42_43
Product data sheet
yes
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
12 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
Table 3.
LPC1313/42/43 LQFP48 pin description table …continued
Symbol
Pin
Start
logic
input
PIO2_10
25[3] yes
PIO2_11/SCK0
31[3]
PIO3_0/DTR
PIO3_1/DSR
PIO3_2/DCD
PIO3_3/RI
36[3]
yes
yes
37[3] yes
43[3] yes
48[3] yes
Type Reset Description
state
[1]
I/O
I; PU
PIO2_10 — General purpose digital input/output pin.
I/O
I; PU
PIO2_11 — General purpose digital input/output pin.
I/O
-
SCK0 — Serial clock for SSP0.
I/O
I; PU
PIO3_0 — General purpose digital input/output pin.
O
-
DTR — Data Terminal Ready output for UART (LPC1311/01 and
LPC1313/01 only).
I/O
I; PU
PIO3_1 — General purpose digital input/output pin.
I
-
DSR — Data Set Ready input for UART (LPC1311/01 and
LPC1313/01 only).
I/O
I; PU
PIO3_2 — General purpose digital input/output pin.
I
-
DCD — Data Carrier Detect input for UART (LPC1311/01 and
LPC1313/01 only).
I/O
I; PU
PIO3_3 — General purpose digital input/output pin.
I
-
RI — Ring Indicator input for UART (LPC1311/01 and LPC1313/01
only).
PIO3_4
18[3] no
I/O
I; PU
PIO3_4 — General purpose digital input/output pin (LPC1313 only).
PIO3_5
21[3]
no
I/O
I; PU
PIO3_5 — General purpose digital input/output pin (LPC1313 only).
USB_DM
19[6]
no
I/O
F
USB_DM — USB bidirectional D line (LPC1342/43 only).
USB_DP
20[6] no
I/O
F
USB_DP — USB bidirectional D+ line (LPC1342/43 only).
VDD
8;
44
-
I
-
3.3 V supply voltage to the internal regulator, the external rail, and
the ADC. Also used as the ADC reference voltage.
XTALIN
6[7]
-
I
-
Input to the oscillator circuit and internal clock generator circuits.
Input voltage must not exceed 1.8 V.
XTALOUT
7[7]
-
O
-
Output from the oscillator amplifier.
VSS
5;
41
-
I
-
Ground.
[1]
Pin state at reset for default function: I = Input; O = Output; PU = internal pull-up enabled (for VDD = 3.3 V, pin is pulled up to 2.6 V for
parts LPC1311/13/42/43 and pulled up to 3.3 V for parts LPC1311/01 and LPC1313/01); IA = inactive, no pull-up/down enabled;
F = floating; floating pins, if not used, should be tied to ground or power to minimize power consumption.
[2]
5 V tolerant pad. See Figure 37 for pad characteristics. RESET functionality is not available in Deep power-down mode. Use the
WAKEUP pin to reset the chip and wake up from Deep power-down mode. An external pull-up resistor is required on this pin for the
Deep power-down mode.
[3]
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors and configurable hysteresis (see Figure 36).
[4]
I2C-bus pads compliant with the I2C-bus specification for I2C standard mode and I2C Fast-mode Plus.
[5]
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors, configurable hysteresis, and analog input.
When configured as a ADC input, digital section of the pad is disabled and the pin is not 5 V tolerant (see Figure 36).
[6]
Pad provides USB functions. It is designed in accordance with the USB specification, revision 2.0 (Full-speed and Low-speed mode
only). This pad is not 5 V tolerant.
[7]
When the system oscillator is not used, connect XTALIN and XTALOUT as follows: XTALIN can be left floating or can be grounded
(grounding is preferred to reduce susceptibility to noise). XTALOUT should be left floating.
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
13 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
Table 4.
LPC1311/13/42/43 HVQFN33 pin description table
Symbol
Pin
Start Type Reset Description
logic
state
[1]
input
RESET/PIO0_0
2[2]
yes
PIO0_1/CLKOUT/
CT32B0_MAT2/
USB_FTOGGLE
3[3]
PIO0_2/SSEL0/
CT16B0_CAP0
8[3]
PIO0_3/
USB_VBUS
9[3]
PIO0_4/SCL
PIO0_5/SDA
yes
yes
yes
10[4] yes
11[4] yes
PIO0_6/
USB_CONNECT/
SCK0
15[3] yes
PIO0_7/CTS
16[3]
PIO0_8/MISO0/
CT16B0_MAT0
17[3]
PIO0_9/MOSI0/
CT16B0_MAT1/
SWO
18[3] yes
LPC1311_13_42_43
Product data sheet
yes
yes
I
I; PU
RESET — External reset input with 20 ns glitch filter. A LOW-going pulse
as short as 50 ns on this pin resets the device, causing I/O ports and
peripherals to take on their default states, and processor execution to
begin at address 0.
I/O
-
PIO0_0 — General purpose digital input/output pin with 10 ns glitch filter.
I/O
I; PU
PIO0_1 — General purpose digital input/output pin. A LOW level on this
pin during reset starts the ISP command handler or the USB device
enumeration (USB on LPC1342/43 only, see description of PIO0_3).
O
-
CLKOUT — Clock out pin.
O
-
CT32B0_MAT2 — Match output 2 for 32-bit timer 0.
O
-
USB_FTOGGLE — USB 1 ms Start-of-Frame signal (LPC1342/43 only).
I/O
I; PU
PIO0_2 — General purpose digital input/output pin.
I/O
-
SSEL0 — Slave select for SSP0.
I
-
CT16B0_CAP0 — Capture input 0 for 16-bit timer 0.
I/O
I; PU
PIO0_3 — General purpose digital input/output pin. LPC1342/43 only: A
LOW level on this pin during reset starts the ISP command handler, a
HIGH level starts the USB device enumeration.
I
-
USB_VBUS — Monitors the presence of USB bus power (LPC1342/43
only).
I/O
I; IA
PIO0_4 — General purpose digital input/output pin (open-drain).
I/O
-
SCL — I2C-bus clock input/output (open-drain). High-current sink only if
I2C Fast-mode Plus is selected in the I/O configuration register.
I/O
I; IA
PIO0_5 — General purpose digital input/output pin (open-drain).
I/O
-
SDA — I2C-bus data input/output (open-drain). High-current sink only if
I2C Fast-mode Plus is selected in the I/O configuration register.
I/O
I; PU
PIO0_6 — General purpose digital input/output pin.
O
-
USB_CONNECT — Signal used to switch an external 1.5 k resistor
under software control. Used with the SoftConnect USB feature
(LPC1342/43 only).
I/O
-
SCK0 — Serial clock for SSP0.
I/O
I; PU
PIO0_7 — General purpose digital input/output pin (high-current output
driver).
I
-
CTS — Clear To Send input for UART.
I/O
I; PU
PIO0_8 — General purpose digital input/output pin.
I/O
-
MISO0 — Master In Slave Out for SSP0.
O
-
CT16B0_MAT0 — Match output 0 for 16-bit timer 0.
I/O
I; PU
PIO0_9 — General purpose digital input/output pin.
I/O
-
MOSI0 — Master Out Slave In for SSP0.
O
-
CT16B0_MAT1 — Match output 1 for 16-bit timer 0.
O
-
SWO — Serial wire trace output.
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
14 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
Table 4.
LPC1311/13/42/43 HVQFN33 pin description table …continued
Symbol
Pin
SWCLK/PIO0_10/
SCK0/
CT16B0_MAT2
19[3] yes
R/PIO0_11/AD0/
CT32B0_MAT3
21[5]
R/PIO1_0/AD1/
CT32B1_CAP0
R/PIO1_1/AD2/
CT32B1_MAT0
R/PIO1_2/AD3/
CT32B1_MAT1
22[5]
Start Type Reset Description
logic
state
[1]
input
yes
yes
23[5] yes
24[5]
SWDIO/PIO1_3/
AD4/
CT32B1_MAT2
25[5]
PIO1_4/AD5/
CT32B1_MAT3/
WAKEUP
26[5]
yes
yes
yes
PIO1_5/RTS/
CT32B0_CAP0
30[3] yes
PIO1_6/RXD/
CT32B0_MAT0
31[3] yes
LPC1311_13_42_43
Product data sheet
I
I; PU
SWCLK — Serial wire clock.
I/O
-
PIO0_10 — General purpose digital input/output pin.
I/O
-
SCK0 — Serial clock for SSP0.
O
-
CT16B0_MAT2 — Match output 2 for 16-bit timer 0.
-
I; PU
R — Reserved. Configure for an alternate function in the IOCONFIG
block.
I/O
-
PIO0_11 — General purpose digital input/output pin.
I
-
AD0 — A/D converter, input 0.
O
-
CT32B0_MAT3 — Match output 3 for 32-bit timer 0.
-
I; PU
R — Reserved. Configure for an alternate function in the IOCONFIG
block.
I/O
-
PIO1_0 — General purpose digital input/output pin.
I
-
AD1 — A/D converter, input 1.
I
-
CT32B1_CAP0 — Capture input 0 for 32-bit timer 1.
-
I; PU
R — Reserved. Configure for an alternate function in the IOCONFIG
block.
I/O
-
PIO1_1 — General purpose digital input/output pin.
I
-
AD2 — A/D converter, input 2.
O
-
CT32B1_MAT0 — Match output 0 for 32-bit timer 1.
-
I; PU
R — Reserved. Configure for an alternate function in the IOCONFIG
block.
I/O
-
PIO1_2 — General purpose digital input/output pin.
I
-
AD3 — A/D converter, input 3.
O
-
CT32B1_MAT1 — Match output 1 for 32-bit timer 1.
I/O
I; PU
SWDIO — Serial wire debug input/output.
I/O
-
PIO1_3 — General purpose digital input/output pin.
I
-
AD4 — A/D converter, input 4.
O
-
CT32B1_MAT2 — Match output 2 for 32-bit timer 1.
I/O
I; PU
PIO1_4 — General purpose digital input/output pin.
I
-
AD5 — A/D converter, input 5.
O
-
CT32B1_MAT3 — Match output 3 for 32-bit timer 1.
I
-
WAKEUP — Deep power-down mode wake-up pin with 20 ns glitch filter.
This pin must be pulled HIGH externally to enter Deep power-down mode
and pulled LOW to exit Deep power-down mode. A LOW-going pulse as
short as 50 ns wakes up the part.
I/O
I; PU
PIO1_5 — General purpose digital input/output pin.
O
-
RTS — Request To Send output for UART.
I
-
CT32B0_CAP0 — Capture input 0 for 32-bit timer 0.
I/O
I; PU
PIO1_6 — General purpose digital input/output pin.
I
-
RXD — Receiver input for UART.
O
-
CT32B0_MAT0 — Match output 0 for 32-bit timer 0.
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
15 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
Table 4.
LPC1311/13/42/43 HVQFN33 pin description table …continued
Symbol
Pin
Start Type Reset Description
logic
state
[1]
input
PIO1_7/TXD/
CT32B0_MAT1
32[3] yes
PIO1_8/
CT16B1_CAP0
7[3]
PIO1_9/
CT16B1_MAT0
12[3]
PIO1_10/AD6/
CT16B1_MAT1
20[5] yes
PIO1_11/AD7
27[5] yes
PIO2_0/DTR
1[3]
PIO3_2
28[3] yes
PIO3_4
13[3]
PIO3_5
14[3]
USB_DM
13[6]
USB_DP
VDD
6;
29
XTALIN
yes
yes
I/O
I; PU
PIO1_7 — General purpose digital input/output pin.
O
-
TXD — Transmitter output for UART.
O
-
CT32B0_MAT1 — Match output 1 for 32-bit timer 0.
I/O
I; PU
PIO1_8 — General purpose digital input/output pin.
I
-
CT16B1_CAP0 — Capture input 0 for 16-bit timer 1.
I/O
I; PU
PIO1_9 — General purpose digital input/output pin.
O
-
CT16B1_MAT0 — Match output 0 for 16-bit timer 1.
I/O
I; PU
PIO1_10 — General purpose digital input/output pin.
I
-
AD6 — A/D converter, input 6.
O
-
CT16B1_MAT1 — Match output 1 for 16-bit timer 1.
I/O
I; PU
PIO1_11 — General purpose digital input/output pin.
I
-
AD7 — A/D converter, input 7.
I/O
I; PU
PIO2_0 — General purpose digital input/output pin.
O
-
DTR — Data Terminal Ready output for UART.
I/O
I; PU
PIO3_2 — General purpose digital input/output pin.
no
I/O
I; PU
PIO3_4 — General purpose digital input/output pin (LPC1311/13 only).
no
I/O
I; PU
PIO3_5 — General purpose digital input/output pin (LPC1311/13 only).
no
I/O
F
USB_DM — USB bidirectional D line (LPC1342/43 only).
14[6] no
I/O
F
USB_DP — USB bidirectional D+ line (LPC1342/43 only).
-
I
-
3.3 V supply voltage to the internal regulator, the external rail, and the
ADC. Also used as the ADC reference voltage.
4[7]
-
I
-
Input to the oscillator circuit and internal clock generator circuits. Input
voltage must not exceed 1.8 V.
XTALOUT
5[7]
-
O
-
Output from the oscillator amplifier.
VSS
33
-
-
-
Thermal pad. Connect to ground.
yes
[1]
Pin state at reset for default function: I = Input; O = Output; PU = internal pull-up enabled (for VDD = 3.3 V, pin is pulled up to 2.6 V for
parts LPC1311/13/42/43 and pulled up to 3.3 V for parts LPC1311/01 and LPC1313/01); IA = inactive, no pull-up/down enabled.
F = floating; floating pins, if not used, should be tied to ground or power to minimize power consumption.
[2]
5 V tolerant pad. See Figure 37 for pad characteristics. RESET functionality is not available in Deep power-down mode. Use the
WAKEUP pin to reset the chip and wake up from Deep power-down mode. An external pull-up resistor is required on this pin for the
Deep power-down mode.
[3]
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors and configurable hysteresis (see Figure 36).
[4]
I2C-bus pads compliant with the I2C-bus specification for I2C standard mode and I2C Fast-mode Plus.
[5]
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors, configurable hysteresis, and analog input.
When configured as a ADC input, digital section of the pad is disabled, and the pin is not 5 V tolerant (see Figure 36).
[6]
Pad provides USB functions. It is designed in accordance with the USB specification, revision 2.0 (Full-speed and Low-speed mode
only). This pad is not 5 V tolerant.
[7]
When the system oscillator is not used, connect XTALIN and XTALOUT as follows: XTALIN can be left floating or can be grounded
(grounding is preferred to reduce susceptibility to noise). XTALOUT should be left floating.
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
16 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
7. Functional description
7.1 Architectural overview
The ARM Cortex-M3 includes three AHB-Lite buses: the system bus, the I-code bus, and
the D-code bus (see Figure 1). The I-code and D-code core buses are faster than the
system bus and are used similarly to TCM interfaces: one bus dedicated for instruction
fetch (I-code) and one bus for data access (D-code). The use of two core buses allows for
simultaneous operations if concurrent operations target different devices.
7.2 ARM Cortex-M3 processor
The ARM Cortex-M3 is a general purpose, 32-bit microprocessor, which offers high
performance and very low power consumption. The ARM Cortex-M3 offers many new
features, including a Thumb-2 instruction set, low interrupt latency, hardware multiply and
divide, interruptible/continuable multiple load and store instructions, automatic state save
and restore for interrupts, tightly integrated interrupt controller, and multiple core buses
capable of simultaneous accesses.
Pipeline techniques are employed so that all parts of the processing and memory systems
can operate continuously. Typically, while one instruction is being executed, its successor
is being decoded, and a third instruction is being fetched from memory.
The ARM Cortex-M3 processor is described in detail in the Cortex-M3 Technical
Reference Manual which is available on the official ARM website.
7.3 On-chip flash program memory
The LPC1311/13/42/43 contain 32 kB (LPC1313 and LPC1343), 16 kB (LPC1342), or
8 kB (LPC1311) of on-chip flash memory.
7.4 On-chip SRAM
The LPC1311/13/42/43 contain a total of 8 kB (LPC1343 and LPC1313) or 4 kB (LPC1342
and LPC1311) on-chip static RAM memory.
7.5 Memory map
The LPC1311/13/42/43 incorporate several distinct memory regions. Figure 6 shows the
overall map of the entire address space from the user program viewpoint following reset.
The interrupt vector area supports address remapping.
The AHB peripheral area is 2 MB in size and is divided to allow for up to 128 peripherals.
The APB peripheral area is 512 kB in size and is divided to allow for up to 32 peripherals.
Each peripheral of either type is allocated 16 kB of space. This allows simplifying the
address decoding for each peripheral.
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
17 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
4 GB
AHB peripherals
LPC1311/13/42/43
0x5020 0000
0xFFFF FFFF
reserved
0xE010 0000
private peripheral bus
16 - 127 reserved
0xE000 0000
0x5004 0000
12-15
GPIO PIO3
0x5020 0000
8-11
GPIO PIO2
0x5000 0000
4-7
GPIO PIO1
0-3
GPIO PIO0
reserved
AHB peripherals
0x5003 0000
0x5002 0000
0x5001 0000
0x5000 0000
reserved
APB peripherals
0x4008 0000
23 - 31 reserved
0x4008 0000
1 GB
APB peripherals
0x4005 C000
22 SSP1 (LPC1313FBD48/01) 0x4005 8000
19 - 21 reserved
0x4004 C000
0x4000 0000
reserved
18
system control
17
IOCONFIG
16
15
SSP0
flash controller
14
PMU
0x4004 8000
0x4004 4000
0x4004 0000
0x4003 C000
0x4003 8000
0x2000 0000
0.5 GB
10 - 13 reserved
reserved
0x4002 8000
0x1FFF 4000
16 kB boot ROM
0x1FFF 0000
reserved
0x1000 2000
8 kB SRAM (LPC1313/1343)
I-code/D-code
memory space
4 kB SRAM (LPC1311/1342)
0x1000 1000
0x1000 0000
reserved
9
reserved
8
USB (LPC1342/43 only)
0x4002 0000
7
ADC
0x4001 C000
6
32-bit counter/timer 1
0x4001 8000
5
32-bit counter/timer 0
0x4001 4000
4
16-bit counter/timer 1
0x4001 0000
3
16-bit counter/timer 0
0x4000 C000
2
UART
0x4000 8000
1
0
WDT/WWDT
0x4000 4000
I2C-bus
0x4000 0000
0x4002 4000
0x0000 8000
32 kB on-chip flash (LPC1313/43)
16 kB on-chip flash (LPC1342)
0 GB
8 kB on-chip flash (LPC1311)
0x0000 4000
+ 256 words
0x0000 2000
active interrupt vectors
0x0000 0400
0x0000 0000
0x0000 0000
002aae723
Fig 6.
LPC1311/13/42/43 memory map
7.6 Nested Vectored Interrupt Controller (NVIC)
The Nested Vectored Interrupt Controller (NVIC) is an integral part of the Cortex-M3. The
tight coupling to the CPU allows for low interrupt latency and efficient processing of late
arriving interrupts.
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
18 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
7.6.1 Features
• Controls system exceptions and peripheral interrupts.
• On the LPC1311/13/42/43, the NVIC supports up to 17 vectored interrupts. In
addition, up to 40 of the individual GPIO inputs are NVIC-vector capable.
• 8 programmable interrupt priority levels, with hardware priority level masking
• Relocatable vector table.
• Software interrupt generation.
7.6.2 Interrupt sources
Each peripheral device has one interrupt line connected to the NVIC but may have several
interrupt flags. Individual interrupt flags may also represent more than one interrupt
source.
Any GPIO pin (total of up to 42 pins) regardless of the selected function, can be
programmed to generate an interrupt on a level, or rising edge or falling edge, or both.
7.7 IOCONFIG block
The IOCONFIG block allows selected pins of the microcontroller to have more than one
function. Configuration registers control the multiplexers to allow connection between the
pin and the on-chip peripherals.
Peripherals should be connected to the appropriate pins prior to being activated and prior
to any related interrupt(s) being enabled. Activity of any enabled peripheral function that is
not mapped to a related pin should be considered undefined.
7.8 Fast general purpose parallel I/O
Device pins that are not connected to a specific peripheral function are controlled by the
GPIO registers. Pins may be dynamically configured as inputs or outputs. Multiple outputs
can be set or cleared in one write operation.
LPC1311/13/42/43 use accelerated GPIO functions:
• GPIO block is a dedicated AHB peripheral so that the fastest possible I/O timing can
be achieved.
• Entire port value can be written in one instruction.
Additionally, any GPIO pin (total of up to 42 pins) providing a digital function can be
programmed to generate an interrupt on a level, a rising or falling edge, or both.
7.8.1 Features
• Bit level port registers allow a single instruction to set or clear any number of bits in
one write operation.
• Direction control of individual bits.
• All I/O default to inputs with pull-up resistors enabled after reset with the exception of
the I2C-bus pins PIO0_4 and PIO0_5.
• Pull-up/pull-down resistor configuration can be programmed through the IOCONFIG
block for each GPIO pin.
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
19 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
• On the LPC1311/13/42/43, all GPIO pins (except PIO0_4 and PIO0_5) are pulled up
to 2.6 V (VDD = 3.3 V) if their pull-up resistor is enabled in the IOCONFIG block.
• On the LPC1311/01 and LPC1313/01, all GPIO pins (except PIO0_4 and PIO0_5) are
pulled up to 3.3 V (VDD = 3.3 V) if their pull-up resistor is enabled in the IOCONFIG
block.
7.9 USB interface (LPC1342/43 only)
The Universal Serial Bus (USB) is a 4-wire bus that supports communication between a
host and one or more (up to 127) peripherals. The host controller allocates the USB
bandwidth to attached devices through a token-based protocol. The bus supports
hot-plugging and dynamic configuration of the devices. All transactions are initiated by the
host controller.
The LPC1342/43 USB interface is a device controller with on-chip PHY for device
functions.
7.9.1 Full-speed USB device controller
The device controller enables 12 Mbit/s data exchange with a USB Host controller. It
consists of a register interface, serial interface engine, and endpoint buffer memory. The
serial interface engine decodes the USB data stream and writes data to the appropriate
endpoint buffer. The status of a completed USB transfer or error condition is indicated via
status registers. An interrupt is also generated if enabled.
7.9.1.1
Features
• Dedicated USB PLL available.
• Fully compliant with USB 2.0 specification (full speed).
• Supports 10 physical (5 logical) endpoints with up to 64 bytes buffer RAM per
endpoint (see Table 5).
• Supports Control, Bulk, Isochronous, and Interrupt endpoints.
• Supports SoftConnect feature.
• Double buffer implementation for Bulk and Isochronous endpoints.
Table 5.
LPC1311_13_42_43
Product data sheet
USB device endpoint configuration
Logical
endpoint
Physical
endpoint
Endpoint type
Direction
Packet size
(byte)
Double buffer
0
0
Control
out
64
no
0
1
Control
in
64
no
1
2
Interrupt/Bulk
out
64
no
1
3
Interrupt/Bulk
in
64
no
2
4
Interrupt/Bulk
out
64
no
2
5
Interrupt/Bulk
in
64
no
3
6
Interrupt/Bulk
out
64
yes
3
7
Interrupt/Bulk
in
64
yes
4
8
Isochronous
out
512
yes
4
9
Isochronous
in
512
yes
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
20 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
7.10 UART
The LPC1311/13/42/43 contains one UART.
Support for RS-485/9-bit mode allows both software address detection and automatic
address detection using 9-bit mode.
The UART includes a fractional baud rate generator. Standard baud rates such as
115200 Bd can be achieved with any crystal frequency above 2 MHz.
7.10.1 Features
•
•
•
•
•
Maximum UART data bit rate of 4.5 MBit/s.
16-byte receive and transmit FIFOs.
Register locations conform to 16C550 industry standard.
Receiver FIFO trigger points at 1 B, 4 B, 8 B, and 14 B.
Built-in fractional baud rate generator covering wide range of baud rates without a
need for external crystals of particular values.
• Fractional divider for baud rate control, auto baud capabilities and FIFO control
mechanism that enables software flow control implementation.
• Support for RS-485/9-bit mode.
• Support for modem control.
7.11 SSP serial I/O controller
The LPC1311/13/42/43 contain one SSP controller. An additional SSP controller is
available on the LPC1313FBD48/01 package.
The SSP controller is capable of operation on a SSP, 4-wire SSI, or Microwire bus. It can
interact with multiple masters and slaves on the bus. Only a single master and a single
slave can communicate on the bus during a given data transfer. The SSP supports full
duplex transfers, with frames of 4 bits to 16 bits of data flowing from the master to the
slave and from the slave to the master. In practice, often only one of these data flows
carries meaningful data.
7.11.1 Features
• Maximum SSP speed of 36 Mbit/s (master) or 6 Mbit/s (slave)
• Compatible with Motorola SPI, 4-wire Texas Instruments SSI, and National
Semiconductor Microwire buses
•
•
•
•
Synchronous serial communication
Master or slave operation
8-frame FIFOs for both transmit and receive
4-bit to 16-bit frame
7.12 I2C-bus serial I/O controller
The LPC1311/13/42/43 contain one I2C-bus controller.
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
21 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
The I2C-bus is bidirectional for inter-IC control using only two wires: a Serial Clock Line
(SCL) and a Serial DAta line (SDA). Each device is recognized by a unique address and
can operate as either a receiver-only device (e.g., an LCD driver) or a transmitter with the
capability to both receive and send information (such as memory). Transmitters and/or
receivers can operate in either master or slave mode, depending on whether the chip has
to initiate a data transfer or is only addressed. The I2C is a multi-master bus and can be
controlled by more than one bus master connected to it.
7.12.1 Features
• The I2C-bus interface is a standard I2C-bus compliant interface with true open-drain
pins. The I2C-bus interface also supports Fast-mode Plus with bit rates up to 1 Mbit/s.
•
•
•
•
•
Easy to configure as master, slave, or master/slave.
Programmable clocks allow versatile rate control.
Bidirectional data transfer between masters and slaves.
Multi-master bus (no central master).
Arbitration between simultaneously transmitting masters without corruption of serial
data on the bus.
• Serial clock synchronization allows devices with different bit rates to communicate via
one serial bus.
• Serial clock synchronization can be used as a handshake mechanism to suspend and
resume serial transfer.
• The I2C-bus can be used for test and diagnostic purposes.
• The I2C-bus controller supports multiple address recognition and a bus monitor mode.
7.13 10-bit ADC
The LPC1311/13/42/43 contains one ADC. It is a single 10-bit successive approximation
ADC with eight channels.
7.13.1 Features
•
•
•
•
•
•
•
•
LPC1311_13_42_43
Product data sheet
10-bit successive approximation ADC.
Input multiplexing among 8 pins.
Power-down mode.
Measurement range 0 V to VDD.
10-bit conversion time 2.44 s (up to 400 kSamples/s).
Burst conversion mode for single or multiple inputs.
Optional conversion on transition of input pin or timer match signal.
Individual result registers for each ADC channel to reduce interrupt overhead.
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
22 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
7.14 General purpose external event counter/timers
The LPC1311/13/42/43 includes two 32-bit counter/timers and two 16-bit counter/timers.
The counter/timer is designed to count cycles of the system derived clock. It can optionally
generate interrupts or perform other actions at specified timer values, based on four
match registers. Each counter/timer also includes one capture input to trap the timer value
when an input signal transitions, optionally generating an interrupt.
7.14.1 Features
• A 32-bit/16-bit counter/timer with a programmable 32-bit/16-bit prescaler.
• Counter or timer operation.
• One capture channel per timer, that can take a snapshot of the timer value when an
input signal transitions. A capture event may also generate an interrupt.
• Four match registers per timer that allow:
– Continuous operation with optional interrupt generation on match.
– Stop timer on match with optional interrupt generation.
– Reset timer on match with optional interrupt generation.
• Up to four external outputs corresponding to match registers, with the following
capabilities:
– Set LOW on match.
– Set HIGH on match.
– Toggle on match.
– Do nothing on match.
7.15 System tick timer
The ARM Cortex-M3 includes a system tick timer (SYSTICK) that is intended to generate
a dedicated SYSTICK exception at a fixed time interval, normally set to 10 ms.
7.16 Watchdog timer
Remark: The standard Watchdog timer is available on parts LPC1311/13/42/43.
The purpose of the watchdog is to reset the microcontroller within a selectable time
period. When enabled, the watchdog will generate a system reset if the user program fails
to ‘feed’ (or reload) the watchdog within a predetermined amount of time.
7.16.1 Features
• Internally resets chip if not periodically reloaded.
• Debug mode.
• Enabled by software but requires a hardware reset or a watchdog reset/interrupt to be
disabled.
• Incorrect/incomplete feed sequence causes reset/interrupt if enabled.
• Flag to indicate watchdog reset.
• Programmable 24-bit timer with internal prescaler.
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
23 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
• Selectable time period from (Tcy(WDCLK) 256 4) to (Tcy(WDCLK) 224 4) in
multiples of Tcy(WDCLK) 4.
• The Watchdog Clock (WDCLK) source can be selected from the Internal RC oscillator
(IRC), the watchdog oscillator, or the main clock. This gives a wide range of potential
timing choices of watchdog operation under different power reduction conditions. It
also provides the ability to run the WDT from an entirely internal source that is not
dependent on an external crystal and its associated components and wiring for
increased reliability.
7.17 Windowed WatchDog Timer (WWDT)
Remark: The windowed watchdog timer is available on parts LPC1311/01 and
LPC1313/01.
The purpose of the watchdog is to reset the controller if software fails to periodically
service it within a programmable time window.
7.17.1 Features
• Internally resets chip if not periodically reloaded during the programmable time-out
period.
• Optional windowed operation requires reload to occur between a minimum and
maximum time period, both programmable.
• Optional warning interrupt can be generated at a programmable time prior to
watchdog time-out.
• Enabled by software but requires a hardware reset or a watchdog reset/interrupt to be
disabled.
•
•
•
•
Incorrect feed sequence causes reset or interrupt if enabled.
Flag to indicate watchdog reset.
Programmable 24-bit timer with internal prescaler.
Selectable time period from (Tcy(WDCLK) 256 4) to (Tcy(WDCLK) 224 4) in
multiples of Tcy(WDCLK) 4.
• The Watchdog Clock (WDCLK) source can be selected from the IRC or the dedicated
watchdog oscillator (WDO). This gives a wide range of potential timing choices of
watchdog operation under different power conditions.
7.18 Clocking and power control
7.18.1 Integrated oscillators
The LPC1311/13/42/43 include three independent oscillators. These are the system
oscillator, the Internal RC oscillator (IRC), and the watchdog oscillator. Each oscillator can
be used for more than one purpose as required in a particular application.
Following reset, the LPC1311/13/42/43 will operate from the internal RC oscillator until
switched by software. This allows systems to operate without any external crystal and the
bootloader code to operate at a known frequency.
See Figure 7 for an overview of the LPC1311/13/42/43 clock generation.
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
24 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
AHB clock 0
(system)
system clock
SYSTEM CLOCK
DIVIDER
AHB clock 1
(ROM)
AHBCLKCTRL
(AHB clock enable)
AHB clocks
2 to 15
(memories
and peripherals)
14
AHBCLKCTRL
AHB clock 16
(IOCONFIG)
AHBCLKCTRL
2
IRC oscillator
SSP0/1 PERIPHERAL
CLOCK DIVIDER
SSP0/1
UART PERIPHERAL
CLOCK DIVIDER
UART
main clock
watchdog oscillator
MAINCLKSEL
(main clock select)
IRC oscillator
ARM TRACE
CLOCK DIVIDER
ARM
trace clock
SYSTICK TIMER
CLOCK DIVIDER
SYSTICK
timer
SYSTEM PLL
system oscillator
IRC oscillator
SYSPLLCLKSEL
(system PLL clock select)
WDT CLOCK
DIVIDER
WDT
USB 48 MHz CLOCK
DIVIDER
USB
CLKOUT PIN CLOCK
DIVIDER
CLKOUT pin
watchdog oscillator
WDTUEN
(WDT clock update enable)
USB PLL
system oscillator
USBPLLCLKSEL
(USB clock select)
USBUEN
(USB clock update enable)
IRC oscillator
system oscillator
watchdog oscillator
CLKOUTUEN
(CLKOUT update enable)
002aae859
The USB clock is available on LPC1342/43 only. SSP1 is available on LPC1313FBD48/01 only.
Fig 7.
LPC1311/13/42/43 clocking generation block diagram
7.18.1.1
Internal RC oscillator
The IRC may be used as the clock source for the WDT, and/or as the clock that drives the
system PLL and subsequently the CPU. The nominal IRC frequency is 12 MHz. The IRC
is trimmed to 1 % accuracy over the entire voltage and temperature range.
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
25 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
Upon power-up, any chip reset, or wake-up from Deep power-down mode, the
LPC1311/13/42/43 use the IRC as the clock source. Software may later switch to one of
the other available clock sources.
7.18.1.2
System oscillator
The system oscillator can be used as the clock source for the CPU, with or without using
the PLL. On the LPC1342/43, the system oscillator must be used to provide the clock
source to USB.
The system oscillator operates at frequencies of 1 MHz to 25 MHz. This frequency can be
boosted to a higher frequency, up to the maximum CPU operating frequency, by the
system PLL.
7.18.1.3
Watchdog oscillator
The watchdog oscillator can be used as a clock source that directly drives the CPU, the
watchdog timer, or the CLKOUT pin. The watchdog oscillator nominal frequency is
programmable between 7.8 kHz and 1.7 MHz. The frequency spread over processing and
temperature is 40 % (see also Table 16).
7.18.2 System PLL and USB PLL
The LPC1342/43 contain a system PLL and a dedicated PLL for generating the 48 MHz
USB clock. The LPC131x contain the system PLL only. The system and USB PLLs are
identical.
The PLL accepts an input clock frequency in the range of 10 MHz to 25 MHz. The input
frequency is multiplied up to a high frequency with a Current Controlled Oscillator (CCO).
The multiplier can be an integer value from 1 to 32. The CCO operates in the range of
156 MHz to 320 MHz, so there is an additional divider in the loop to keep the CCO within
its frequency range while the PLL is providing the desired output frequency. The output
divider may be set to divide by 2, 4, 8, or 16 to produce the output clock. The PLL output
frequency must be lower than 100 MHz. Since the minimum output divider value is 2, it is
insured that the PLL output has a 50 % duty cycle. The PLL is turned off and bypassed
following a chip reset and may be enabled by software. The program must configure and
activate the PLL, wait for the PLL to lock, and then connect to the PLL as a clock source.
The PLL settling time is 100 s.
7.18.3 Clock output
The LPC1311/13/42/43 features a clock output function that routes the IRC oscillator, the
system oscillator, the watchdog oscillator, or the main clock to an output pin.
7.18.4 Wake-up process
The LPC1311/13/42/43 begin operation at power-up and when awakened from Deep
power-down mode by using the 12 MHz IRC oscillator as the clock source. This allows
chip operation to resume quickly. If the main oscillator or the PLL is needed by the
application, software will need to enable these features and wait for them to stabilize
before they are used as a clock source.
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
26 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
7.18.5 Power control
The LPC1311/13/42/43 support a variety of power control features. There are three
special modes of processor power reduction: Sleep mode, Deep-sleep mode, and Deep
power-down mode. The CPU clock rate may also be controlled as needed by changing
clock sources, reconfiguring PLL values, and/or altering the CPU clock divider value. This
allows a trade-off of power versus processing speed based on application requirements.
In addition, a register is provided for shutting down the clocks to individual on-chip
peripherals, allowing fine tuning of power consumption by eliminating all dynamic power
use in any peripherals that are not required for the application. Selected peripherals have
their own clock divider which provides even better power control.
7.18.5.1
Power profiles (LPC1300L series, LPC1311/01 and LPC1313/01 only)
The power consumption in Active and Sleep modes can be optimized for the application
through simple calls to the power profile. The power configuration routine configures the
LPC1311/01 and the LPC1313/01 for one of the following power modes:
• Default mode corresponding to power configuration after reset.
• CPU performance mode corresponding to optimized processing capability.
• Efficiency mode corresponding to optimized balance of current consumption and CPU
performance.
• Low-current mode corresponding to lowest power consumption.
In addition, the power profile includes routines to select the optimal PLL settings for a
given system clock and PLL input clock.
7.18.5.2
Sleep mode
When Sleep mode is entered, the clock to the core is stopped. Resumption from the Sleep
mode does not need any special sequence but re-enabling the clock to the ARM core.
In Sleep mode, execution of instructions is suspended until either a reset or interrupt
occurs. Peripheral functions continue operation during Sleep mode and may generate
interrupts to cause the processor to resume execution. Sleep mode eliminates dynamic
power used by the processor itself, memory systems and related controllers, and internal
buses.
7.18.5.3
Deep-sleep mode
In Deep-sleep mode, the chip is in Sleep mode, and in addition all analog blocks are shut
down. As an exception, the user has the option to keep the watchdog oscillator and the
BOD circuit running for self-timed wake-up and BOD protection. Deep-sleep mode allows
for additional power savings.
Up to 40 pins total can serve as external wake-up pins to the start logic to wake up the
chip from Deep-sleep mode (see Section 7.19.1).
Unless the watchdog oscillator is selected to run in Deep-sleep mode, the clock source
should be switched to IRC before entering Deep-sleep mode, because the IRC can be
switched on and off glitch-free.
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
27 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
7.18.5.4
Deep power-down mode
In Deep power-down mode, power is shut off to the entire chip with the exception of the
WAKEUP pin. The LPC1311/13/42/43 can wake up from Deep power-down mode via the
WAKEUP pin.
A LOW-going pulse as short as 50 ns wakes up the part from Deep power-down mode.
When entering Deep power-down mode, an external pull-up resistor is required on the
WAKEUP pin to hold it HIGH. The RESET pin must also be held HIGH to prevent it from
floating while in Deep power-down mode.
7.19 System control
7.19.1 Start logic
The start logic connects external pins to corresponding interrupts in the NVIC. Each pin
shown in Table 3 and Table 4 as input to the start logic has an individual interrupt in the
NVIC interrupt vector table. The start logic pins can serve as external interrupt pins when
the chip is running. In addition, an input signal on the start logic pins can wake up the chip
from Deep-sleep mode when all clocks are shut down.
The start logic must be configured in the system configuration block and in the NVIC
before being used.
7.19.2 Reset
Reset has four sources on the LPC1311/13/42/43: the RESET pin, the Watchdog reset,
power-on reset (POR), and the Brown-Out Detection (BOD) circuit. The RESET pin is a
Schmitt trigger input pin. Assertion of chip reset by any source, once the operating voltage
attains a usable level, starts the IRC and initializes the flash controller.
When the internal reset is removed, the processor begins executing at address 0, which is
initially the reset vector mapped from the boot block. At that point, all of the processor and
peripheral registers have been initialized to predetermined values.
7.19.3 Brownout detection
The LPC1311/13/42/43 includes four levels for monitoring the voltage on the VDD pin. If
this voltage falls below one of the four selected levels, the BOD asserts an interrupt signal
to the NVIC. This signal can be enabled for interrupt in the Interrupt Enable Register in the
NVIC in order to cause a CPU interrupt; if not, software can monitor the signal by reading
a dedicated status register. An additional threshold level can be selected to cause a
forced reset of the chip.
7.19.4 Code security (Code Read Protection - CRP)
This feature of the LPC1311/13/42/43 allows user to enable different levels of security in
the system so that access to the on-chip flash and use of the Serial Wire Debugger (SWD)
and In-System Programming (ISP) can be restricted. When needed, CRP is invoked by
programming a specific pattern into a dedicated flash location. In-Application
Programming (IAP) commands are not affected by the CRP.
In addition, ISP entry via the PIO0_1 pin can be disabled without enabling CRP (NO_ISP
mode). For details see the LPC13xx user manual.
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
28 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
There are three levels of Code Read Protection:
1. CRP1 disables access to chip via the SWD and allows partial flash update (excluding
flash sector 0) using a limited set of the ISP commands. This mode is useful when
CRP is required and flash field updates are needed but all sectors can not be erased.
2. CRP2 disables access to chip via the SWD and only allows full flash erase and
update using a reduced set of the ISP commands.
3. Running an application with level CRP3 selected fully disables any access to chip via
the SWD pins and the ISP. This mode effectively disables ISP override using PIO0_1
pin, too. It is up to the user’s application to provide (if needed) flash update
mechanism using IAP calls or call reinvoke ISP command to enable flash update via
UART.
CAUTION
If level three Code Read Protection (CRP3) is selected, no future factory testing can be
performed on the device.
7.19.5 Boot loader
The boot loader controls initial operation after reset and also provides the means to
program the flash memory. This could be initial programming of a blank device, erasure
and re-programming of a previously programmed device, or programming of the flash
memory by the application program in a running system.
The boot loader code is executed every time the part is reset or powered up. The loader
can either execute the ISP command handler or the user application code, or, on the
LPC1342/43, it can program the flash image via an attached MSC device through USB
(Windows operating system only). A LOW level during reset applied to the PIO0_1 pin is
considered as an external hardware request to start the ISP command handler or the USB
device enumeration. The state of PIO0_3 determines whether the UART or USB interface
will be used (LPC1342/43 only).
7.19.6 APB interface
The APB peripherals are located on one APB bus.
7.19.7 AHB-Lite
The AHB-Lite connects the instruction (I-code) and data (D-code) CPU buses of the ARM
Cortex-M3 to the flash memory, the main static RAM, and the boot ROM.
7.19.8 External interrupt inputs
All GPIO pins can be level or edge sensitive interrupt inputs. In addition, start logic inputs
serve as external interrupts (see Section 7.19.1).
7.19.9 Memory mapping control
The Cortex-M3 incorporates a mechanism that allows remapping the interrupt vector table
to alternate locations in the memory map. This is controlled via the Vector Table Offset
Register contained in the NVIC.
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
29 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
The vector table may be located anywhere within the bottom 1 GB of Cortex-M3 address
space. The vector table must be located on a 256 word boundary.
7.20 Emulation and debugging
Debug functions are integrated into the ARM Cortex-M3. Serial wire debug is supported.
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
30 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
8. Limiting values
Table 6.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).[1]
Symbol
Parameter
Conditions
Min
Max
Unit
VDD
supply voltage (core and
external rail)
2.0
3.6
V
VI
input voltage
5 V tolerant I/O pins; only valid
when the VDD supply voltage is
present
[2]
0.5
+5.5
V
IDD
supply current
per supply pin
[3]
ISS
-
100
mA
ground current
per ground pin
[3]
-
100
mA
Ilatch
I/O latch-up current
(0.5VDD) < VI < (1.5VDD);
-
100
mA
Tstg
storage temperature
non-operating
65
+150
C
Tj(max)
maximum junction temperature
-
150
C
Ptot(pack)
total power dissipation (per
package)
based on package heat transfer, not
device power consumption
-
1.5
W
VESD
electrostatic discharge voltage
human body model; all pins
6500
+6500
V
Tj < 125 C
[1]
[4]
[5]
The following applies to the limiting values:
a) This product includes circuitry specifically designed for the protection of its internal devices from the damaging effects of excessive
static charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated
maximum.
b) Parameters are valid over operating temperature range unless otherwise specified. All voltages are with respect to VSS unless
otherwise noted.
[2]
Including voltage on outputs in 3-state mode.
[3]
The peak current is limited to 25 times the corresponding maximum current.
[4]
The maximum non-operating storage temperature is different than the temperature for required shelf life which should be determined
based on required shelf lifetime. Please refer to the JEDEC specification J-STD-033B.1 for further details.
[5]
Human body model: equivalent to discharging a 100 pF capacitor through a 1.5 k series resistor.
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
31 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
9. Static characteristics
Table 7.
Static characteristics
Tamb = 40 C to +85 C, unless otherwise specified.
Symbol Parameter
VDD
Min
Typ[1]
Max
Unit
2.0
3.3
3.6
V
-
4
-
mA
-
17
-
mA
-
2
-
mA
[4][9][7]
-
30
-
A
[10]
-
220
-
nA
-
2
-
mA
-
13
-
mA
-
1
-
mA
[4][9][7]
-
2
-
A
[10]
-
220
-
nA
Conditions
[2]
supply voltage (core
and external rail)
LPC1300 series (LPC1311/13/42/43) power consumption
IDD
supply current
Active mode; VDD = 3.3 V;
Tamb = 25 C; code
while(1){}
executed from flash;
system clock = 12 MHz
[3][4][5]
[6][7]
system clock = 72 MHz
[4][5][6]
[8][7]
Sleep mode;
VDD = 3.3 V; Tamb = 25 C;
[3][4][5]
[6][7]
system clock = 12 MHz
Deep-sleep mode; VDD = 3.3 V;
Tamb = 25 C
Deep power-down mode;
VDD = 3.3 V; Tamb = 25 C
LPC1300L series (LPC1311/01, LPC1313/01) power consumption in low-current mode[11]
IDD
supply current
Active mode; VDD = 3.3 V;
Tamb = 25 C; code
while(1){}
executed from flash;
system clock = 12 MHz
[3][4][5]
[6][7]
system clock = 72 MHz
[4][5][6]
[8][7]
Sleep mode;
VDD = 3.3 V; Tamb = 25 C;
[3][4][5]
[6][7]
system clock = 12 MHz
Deep-sleep mode; VDD = 3.3 V;
Tamb = 25 C
Deep power-down mode;
VDD = 3.3 V; Tamb = 25 C
Standard port pins and RESET pin; see Figure 21, Figure 22, Figure 23, Figure 24
IIL
LOW-level input current VI = 0 V; on-chip pull-up resistor
disabled
-
0.5
10
nA
IIH
HIGH-level input
current
VI = VDD; on-chip pull-down resistor
disabled
-
0.5
10
nA
IOZ
OFF-state output
current
VO = 0 V; VO = VDD; on-chip
pull-up/down resistors disabled
-
0.5
10
nA
VI
input voltage
pin configured to provide a digital
function
0
-
5.0
V
LPC1311_13_42_43
Product data sheet
[12][13]
[14]
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
32 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
Table 7.
Static characteristics …continued
Tamb = 40 C to +85 C, unless otherwise specified.
Symbol Parameter
Conditions
Min
Typ[1]
Max
Unit
VO
output voltage
output active
0
-
VDD
V
VIH
HIGH-level input
voltage
0.7VDD
-
-
V
VIL
LOW-level input voltage
-
-
0.3VDD
V
Vhys
hysteresis voltage
0.4
-
-
V
VOH
HIGH-level output
voltage
IOH = 4 mA
VDD 0.4 -
-
V
VOL
LOW-level output
voltage
IOL = 4 mA
-
-
0.4
V
IOH
HIGH-level output
current
VOH = VDD 0.4 V
4
-
-
mA
IOL
LOW-level output
current
VOL = 0.4 V
4
-
-
mA
IOHS
HIGH-level short-circuit VOH = 0 V
output current
[15]
-
-
45
mA
IOLS
LOW-level short-circuit
output current
VOL = VDD
[15]
-
-
50
mA
Ipd
pull-down current
VI = 5 V
10
50
150
A
Ipu
pull-up current
VI = 0 V
15
50
85
A
VDD < VI < 5 V
0
0
0
A
High-drive output pin (PIO0_7); see Figure 19 and Figure 21
IIL
LOW-level input current VI = 0 V; on-chip pull-up resistor
disabled
-
0.5
10
nA
IIH
HIGH-level input
current
VI = VDD; on-chip pull-down resistor
disabled
-
0.5
10
nA
IOZ
OFF-state output
current
VO = 0 V; VO = VDD; on-chip
pull-up/down resistors disabled
-
0.5
10
nA
VI
input voltage
pin configured to provide a digital
function
0
-
5.0
V
0
-
VDD
V
[12][13]
[14]
VO
output voltage
VIH
HIGH-level input
voltage
0.7VDD
-
-
V
VIL
LOW-level input voltage
-
-
0.3VDD
V
Vhys
hysteresis voltage
0.4
-
-
V
VOH
HIGH-level output
voltage
2.5 V VDD 3.6 V; IOH = 20 mA
VDD 0.4 -
-
V
2.0 V VDD < 2.5 V; IOH = 12 mA
VDD 0.4 -
-
V
VOL
LOW-level output
voltage
IOL = 4 mA
-
-
0.4
V
IOH
HIGH-level output
current
VOH = VDD 0.4 V;
2.5 V VDD 3.6 V
20
-
-
mA
2.0 V VDD 2.5 V
12
-
-
mA
output active
IOL
LOW-level output
current
VOL = 0.4 V
4
-
-
mA
Ipd
pull-down current
VI = 5 V
10
50
150
A
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
33 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
Table 7.
Static characteristics …continued
Tamb = 40 C to +85 C, unless otherwise specified.
Symbol Parameter
Conditions
Min
Typ[1]
Max
Unit
Ipu
VI = 0 V
15
50
85
A
VDD < VI < 5 V
0
0
0
A
pull-up current
I2C-bus
pins (PIO0_4 and PIO0_5); see Figure 20
VIH
HIGH-level input
voltage
0.7VDD
-
-
V
VIL
LOW-level input voltage
-
-
0.3VDD
V
Vhys
hysteresis voltage
IOL
LOW-level output
current
VOL = 0.4 V; 2.0 V VDD 3.6 V
input leakage current
0.05VDD
-
V
-
-
mA
20
-
-
mA
-
2
4
A
-
10
22
A
I2C-bus
pins configured as
standard mode pins
I2C-bus pins configured as
Fast-mode Plus pins
ILI
3.5
[16]
VI = VDD
VI = 5 V
Oscillator pins
Vi(xtal)
crystal input voltage
0.5
+1.8
+1.95
V
Vo(xtal)
crystal output voltage
0.5
+1.8
+1.95
V
[17]
-
-
10
A
[17]
-
-
5.25
V
0.2
-
-
V
USB pins (LPC1342/43 only)
IOZ
OFF-state output
current
VBUS
bus supply voltage
0 V < VI < 3.3 V
VDI
differential input
sensitivity voltage
(D+) (D)
[17]
VCM
differential common
mode voltage range
includes VDI range
[17]
0.8
-
2.5
V
Vth(rs)se
single-ended receiver
switching threshold
voltage
[17]
0.8
-
2.0
V
VOL
LOW-level output
voltage
for low-/full-speed;
RL of 1.5 k to 3.6 V
[17]
-
-
0.18
V
VOH
HIGH-level output
voltage
driven; for low-/full-speed;
RL of 15 k to GND
[17]
2.8
-
3.5
V
Ctrans
transceiver capacitance pin to GND
[17]
-
-
20
pF
ZDRV
driver output
with 33 series resistor; steady state
impedance for driver
drive
which is not high-speed
capable
36
-
44.1
[18][17]
[1]
Typical ratings are not guaranteed. The values listed are at room temperature (25 C), nominal supply voltages.
[2]
For LPC1342 and LPC1343 only: For USB operation 3.0 V VDD 3.6 V. Guaranteed by design.
[3]
IRC enabled; system oscillator disabled; system PLL disabled.
[4]
IDD measurements were performed with all pins configured as GPIO outputs driven LOW and pull-up resistors disabled.
[5]
BOD disabled.
[6]
All peripherals disabled in the SYSAHBCLKCTRL register. Peripheral clocks to UART, SSP, trace clock, and SysTick timer disabled in
the syscon block.
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
34 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
[7]
For LPC1342/43: USB_DP and USB_DM pulled LOW externally.
[8]
IRC disabled; system oscillator enabled; system PLL enabled.
[9]
All oscillators and analog blocks turned off in the PDSLEEPCFG register; PDSLEEPCFG = 0x0000 0FFF.
[10] WAKEUP pin pulled HIGH externally. An external pull-up resistor is required on the RESET pin for the Deep power-down mode.
[11] Low-current mode PWR_LOW_CURRENT selected when running the set_power routine in the power profiles.
[12] Including voltage on outputs in 3-state mode.
[13] VDD supply voltage must be present.
[14] 3-state outputs go into 3-state mode in Deep power-down mode.
[15] Allowed as long as the current limit does not exceed the maximum current allowed by the device.
[16] To VSS.
[17] 3.0 V VDD 3.6 V.
[18] Includes external resistors of 33 1 % on USB_DP and USB_DM.
Table 8.
ADC static characteristics
Tamb = 40 C to +85 C unless otherwise specified; ADC frequency 4.5 MHz, VDD = 2.5 V to 3.6 V.
Symbol
Parameter
VIA
analog input voltage
0
-
VDD
V
Cia
analog input capacitance
-
-
1
pF
ED
differential linearity error
[1][2]
-
-
1
LSB
integral non-linearity
[3]
-
-
1.5
LSB
EO
offset error
[4]
-
-
3.5
LSB
EG
gain error
[5]
-
-
0.6
%
ET
absolute error
[6]
-
-
4
LSB
Rvsi
voltage source interface
resistance
-
-
40
k
Ri
input resistance
-
-
2.5
M
EL(adj)
Conditions
Min
[7][8]
Typ
Max
Unit
[1]
The ADC is monotonic, there are no missing codes.
[2]
The differential linearity error (ED) is the difference between the actual step width and the ideal step width. See Figure 8.
[3]
The integral non-linearity (EL(adj)) is the peak difference between the center of the steps of the actual and the ideal transfer curve after
appropriate adjustment of gain and offset errors. See Figure 8.
[4]
The offset error (EO) is the absolute difference between the straight line which fits the actual curve and the straight line which fits the
ideal curve. See Figure 8.
[5]
The gain error (EG) is the relative difference in percent between the straight line fitting the actual transfer curve after removing offset
error, and the straight line which fits the ideal transfer curve. See Figure 8.
[6]
The absolute error (ET) is the maximum difference between the center of the steps of the actual transfer curve of the non-calibrated
ADC and the ideal transfer curve. See Figure 8.
[7]
Tamb = 25 C; maximum sampling frequency fs = 400 kSamples/s and analog input capacitance Cia = 1 pF.
[8]
Input resistance Ri depends on the sampling frequency fs: Ri = 1 / (fs Cia).
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
35 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
offset
error
EO
gain
error
EG
1023
1022
1021
1020
1019
1018
(2)
7
code
out
(1)
6
5
(5)
4
(4)
3
(3)
2
1 LSB
(ideal)
1
0
1
2
3
4
5
6
7
1018
1019
1020
1021
1022
1023
1024
VIA (LSBideal)
offset error
EO
1 LSB =
VDD − VSS
1024
002aaf426
(1) Example of an actual transfer curve.
(2) The ideal transfer curve.
(3) Differential linearity error (ED).
(4) Integral non-linearity (EL(adj)).
(5) Center of a step of the actual transfer curve.
Fig 8.
ADC characteristics
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
36 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
9.1 BOD static characteristics for LPC1300 series
Remark: Applies to parts LPC1311/13/42/43 and all their packages.
Table 9.
BOD static characteristics[1]
Tamb = 25 C.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Vth
threshold voltage
interrupt level 0
assertion
-
1.69
-
V
de-assertion
-
1.84
-
V
assertion
-
2.29
-
V
de-assertion
-
2.44
-
V
interrupt level 1
interrupt level 2
assertion
-
2.59
-
V
de-assertion
-
2.74
-
V
assertion
-
2.87
-
V
de-assertion
-
2.98
-
V
assertion
-
1.49
-
V
de-assertion
-
1.64
-
V
interrupt level 3
reset level 0
[1]
LPC1311_13_42_43
Product data sheet
Interrupt levels are selected by writing the level value to the BOD control register BODCTRL, see LPC13xx
user manual.
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
37 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
9.2 BOD static characteristics for LPC1300L series (LPC1311/01 and
LPC1313/01)
Remark: Applies to parts LPC1311/01 and LPC1313/01 and all packages.
Table 10. BOD static characteristics[1]
Tamb = 25 C.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Vth
threshold voltage
interrupt level 0
assertion
-
1.65
-
V
de-assertion
-
1.80
-
V
interrupt level 1
assertion
-
2.22
-
V
de-assertion
-
2.35
-
V
assertion
-
2.52
-
V
de-assertion
-
2.66
-
V
assertion
-
2.80
-
V
de-assertion
-
2.90
-
V
interrupt level 2
interrupt level 3
reset level 0
assertion
-
1.46
-
V
de-assertion
-
1.63
-
V
assertion
-
2.06
-
V
de-assertion
-
2.15
-
V
assertion
-
2.35
-
V
de-assertion
-
2.43
-
V
assertion
-
2.63
-
V
de-assertion
-
2.71
-
V
reset level 1
reset level 2
reset level 3
[1]
Interrupt levels are selected by writing the level value to the BOD control register BODCTRL, see LPC13xx
user manual.
9.3 Power consumption for LPC1300 series
Remark: Applies to parts LPC1311/13/42/43 and all their packages.
Power measurements in Active, Sleep, and Deep-sleep modes were performed under the
following conditions (see LPC13xx user manual):
• Configure all pins as GPIO with pull-up resistor disabled in the IOCONFIG block.
• Configure GPIO pins as outputs using the GPIOnDIR registers.
• Write 0 to all GPIOnDATA registers to drive the outputs LOW.
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
38 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
002aae993
18
IDD
(mA)
72 MHz
15
12
9
48 MHz
36 MHz
24 MHz
6
12 MHz
3
2.0
2.4
2.8
3.2
3.6
VDD (V)
Conditions: Tamb = 25 C; Active mode entered executing code while(1){} from flash;
internal pull-up resistors disabled; system oscillator and system PLL enabled; IRC, BOD disabled;
all peripherals disabled in the SYSAHBCLKCTRL register (SYSAHBCLKCTRL = 0x1F); all
peripheral clocks disabled; USB_DP and USB_DM pulled LOW externally (LPC1342/43).
Fig 9.
Typical supply current versus regulator supply voltage VDD in Active mode
(LPC1311/13/42/43)
002aae994
18
IDD
(mA)
72 MHz
15
48 MHz
12
36 MHz
9
24 MHz
6
12 MHz
3
−40
−15
10
35
60
85
temperature (°C)
Conditions: VDD = 3.3 V; Active mode entered executing code while(1){} from flash; internal pull-up
resistors disabled; system oscillator and system PLL enabled; IRC, BOD disabled; all peripherals
disabled in the SYSAHBCLKCTRL register (SYSAHBCLKCTRL = 0x1F); all peripheral clocks
disabled; USB_DP and USB_DM pulled LOW externally (LPC1342/43).
Fig 10. Typical supply current versus temperature in Active mode (LPC1311/13/42/43)
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
39 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
002aae995
10
72 MHz
IDD
(mA)
8
48 MHz
6
36 MHz
4
24 MHz
12 MHz
2
0
−40
−15
10
35
60
85
temperature (°C)
Conditions: VDD = 3.3 V; Sleep mode entered from flash; internal pull-up resistors disabled; system
oscillator and system PLL enabled; IRC, BOD disabled; all peripherals disabled in the
SYSAHBCLKCTRL register (SYSAHBCLKCTRL = 0x1F); all peripheral clocks disabled; USB_DP
and USB_DM pulled LOW externally (LPC1342/43).
Fig 11. Typical supply current versus temperature in Sleep mode (LPC1311/13/42/43)
002aae998
80
IDD
(μA)
60
VDD = 3.6 V
3.3 V
2.0 V
40
20
0
−40
−15
10
35
60
85
temperature (°C)
Conditions: BOD disabled; all oscillators and analog blocks turned off in the PDSLEEPCFG
register; PDSLEEPCFG = 0x0000 0FFF; USB_DP and USB_DM pulled LOW externally
(LPC1342/43).
Fig 12. Typical supply current versus temperature in Deep-sleep mode (analog blocks
disabled; LPC1311/13/42/43)
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
40 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
002aae996
1.2
IDD
(μA)
0.6
VDD = 3.6 V
3.3 V
2.0 V
0.4
0
−40
−15
10
35
60
85
temperature (°C)
Fig 13. Typical supply current versus temperature in Deep power-down mode
(LPC1311/13/42/43)
9.4 Power consumption for LPC1300L series (LPC1311/01 and
LPC1313/01)
Remark: Applies to parts LPC1311/01 and LPC1313/01 and all their packages.
Power measurements in Active, Sleep, and Deep-sleep modes were performed under the
following conditions (see LPC13xx user manual):
• Configure all pins as GPIO with pull-up resistor disabled in the IOCONFIG block.
• Configure GPIO pins as outputs using the GPIOnDIR registers.
• Write 0 to all GPIOnDATA registers to drive the outputs LOW.
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
41 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
002aag235
16
IDD
(mA)
72 MHz
12
8
48 MHz
36 MHz
4
24 MHz
12 MHz
0
2.0
2.4
2.8
3.2
3.6
VDD (V)
Conditions: Tamb = 25 C; Active mode entered executing code while(1){} from flash;
internal pull-up resistors disabled; system oscillator and system PLL enabled; IRC, BOD disabled;
all peripherals disabled in the SYSAHBCLKCTRL register (SYSAHBCLKCTRL = 0x1F); all
peripheral clocks disabled; low-current mode.
Fig 14. Typical supply current versus regulator supply voltage VDD in Active mode
(LPC1311/01 and LPC1313/01)
002aag236
16
IDD
(mA)
72 MHz
12
48 MHz
8
36 MHz
24 MHz
4
12 MHz
0
˗40
˗15
10
35
60
85
temperature (°C)
Conditions: VDD = 3.3 V; Active mode entered executing code while(1){} from flash; internal pull-up
resistors disabled; system oscillator and system PLL enabled; IRC, BOD disabled; all peripherals
disabled in the SYSAHBCLKCTRL register (SYSAHBCLKCTRL = 0x1F); all peripheral clocks
disabled; low-current mode.
Fig 15. Typical supply current versus temperature in Active mode (LPC1311/01 and
LPC1313/01)
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
42 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
002aag237
8
72 MHz
IDD
(mA)
6
48 MHz
4
36 MHz
24 MHz
2
12 MHz
0
˗40
˗15
10
35
60
85
temperature (°C)
Conditions: VDD = 3.3 V; Sleep mode entered from flash; internal pull-up resistors disabled; system
oscillator and system PLL enabled; IRC, BOD disabled; all peripherals disabled in the
SYSAHBCLKCTRL register (SYSAHBCLKCTRL = 0x1F); all peripheral clocks disabled;
low-current mode.
Fig 16. Typical supply current versus temperature in Sleep mode (LPC1311/01 and
LPC1313/01)
002aag238
8
IDD
(μA)
6
VDD = 2.0 V
3.3 V
3.6 V
4
2
0
˗40
˗15
10
35
60
85
temperature (°C)
Conditions: BOD disabled; all oscillators and analog blocks turned off in the PDSLEEPCFG
register; PDSLEEPCFG = 0x0000 0FFF.
Fig 17. Typical supply current versus temperature in Deep-sleep mode (analog blocks
disabled, LPC1311/01 and LPC1313/01)
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
43 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
002aag239
0.6
IDD
(µA)
VDD = 3.6 V
3.3 V
2.0 V
0.4
0.2
0
˗40
˗15
10
35
60
85
temperature (°C)
Fig 18. Typical supply current versus temperature in Deep power-down mode
(LPC1311/01 and LPC1313/01)
9.5 Peripheral power consumption
The supply current per peripheral is measured as the difference in supply current between
the peripheral block enabled and the peripheral block disabled in the SYSAHBCLKCFG or
PDRUNCFG (for analog blocks) registers. All other blocks are disabled in both registers
and no code is executed. Measured on a typical sample at Tamb = 25 C. Unless noted
otherwise, the system oscillator and PLL are running in both measurements.
The supply currents are shown for system clock frequencies of 12 MHz, 48 MHz, and
72 MHz.
Table 11.
Power consumption for individual analog and digital blocks
Peripheral
Typical supply current in mA
Notes
n/a
12 MHz
48 MHz
72 MHz
IRC
0.23
-
-
-
System oscillator running; PLL off; independent of main clock
frequency.
System oscillator
at 12 MHz
0.23
-
-
-
IRC running; PLL off; independent of main clock frequency.
Watchdog
oscillator at
500 kHz/2
0.002
-
-
-
System oscillator running; PLL off; independent of main clock
frequency.
BOD
0.045
-
-
-
Independent of main clock frequency.
Main or USB PLL
-
0.26
0.34
0.48
ADC
-
0.07
0.25
0.37
CLKOUT
-
0.14
0.56
0.82
CT16B0
-
0.01
0.05
0.08
CT16B1
-
0.01
0.04
0.06
CT32B0
-
0.01
0.05
0.07
CT32B1
-
0.01
0.04
0.06
LPC1311_13_42_43
Product data sheet
Main clock divided by 4 in the CLKOUTDIV register.
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
44 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
Table 11.
Power consumption for individual analog and digital blocks …continued
Peripheral
Typical supply current in mA
Notes
n/a
12 MHz
48 MHz
72 MHz
GPIO
-
0.21
0.80
1.17
IOCONFIG
-
0.00
0.02
0.02
I2C
-
0.03
0.12
0.17
ROM
-
0.04
0.15
0.22
GPIO pins configured as outputs and set to LOW. Direction
and pin state are maintained if the GPIO is disabled in the
SYSAHBCLKCFG register.
SSP0
-
0.11
0.41
0.60
SSP1
-
0.11
0.41
0.60
UART
-
0.20
0.76
1.11
WDT
-
0.01
0.05
0.08
Main clock selected as clock source for the WDT.
USB
-
-
3.91
-
Main clock selected as clock source for the USB. USB_DP
and USB_DM pulled LOW externally.
USB
-
1.84
4.19
5.71
Dedicated USB PLL selected as cock source for the USB.
USB_DP and USB_DM pulled LOW externally.
On LPC1313FBD48/01 only.
9.6 Electrical pin characteristics
002aae990
3.6
VOH
(V)
T = 85 °C
25 °C
−40 °C
3.2
2.8
2.4
2
0
10
20
30
40
50
60
IOH (mA)
Conditions: VDD = 3.3 V; on pin PIO0_7.
Fig 19. High-drive output: Typical HIGH-level output voltage VOH versus HIGH-level
output current IOH.
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
45 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
002aaf019
60
T = 85 °C
25 °C
−40 °C
IOL
(mA)
40
20
0
0
0.2
0.4
0.6
VOL (V)
Conditions: VDD = 3.3 V; on pins PIO0_4 and PIO0_5.
Fig 20. I2C-bus pins (high current sink): Typical LOW-level output current IOL versus
LOW-level output voltage VOL
002aae991
15
IOL
(mA)
T = 85 °C
25 °C
−40 °C
10
5
0
0
0.2
0.4
0.6
VOL (V)
Conditions: VDD = 3.3 V; standard port pins and PIO0_7.
Fig 21. Typical LOW-level output current IOL versus LOW-level output voltage VOL
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
46 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
002aae992
3.6
VOH
(V)
T = 85 °C
25 °C
−40 °C
3.2
2.8
2.4
2
0
8
16
24
IOH (mA)
Conditions: VDD = 3.3 V; standard port pins.
Fig 22. Typical HIGH-level output voltage VOH versus HIGH-level output source current
IOH
002aae988
10
Ipu
(μA)
−10
−30
T = 85 °C
25 °C
−40 °C
−50
−70
0
1
2
3
4
5
VI (V)
Conditions: VDD = 3.3 V; standard port pins.
Fig 23. Typical pull-up current Ipu versus input voltage Vi
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
47 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
002aae989
80
T = 85 °C
25 °C
−40 °C
Ipd
(μA)
60
40
20
0
0
1
2
3
4
5
VI (V)
Conditions: VDD = 3.3 V; standard port pins.
Fig 24. Typical pull-down current Ipd versus input voltage Vi
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
48 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
10. Dynamic characteristics
10.1 Power-up ramp conditions
Table 12. Power-up characteristics
Tamb = 40 C to +85 C.
Symbol Parameter
tr
rise time
twait
wait time
VI
input voltage
Conditions
Min
at t = t1: 0 < VI 400 mV
[1]
[1][2]
at t = t1 on pin VDD
Typ
Max
Unit
0
-
500
ms
12
-
-
s
0
-
400
mV
[1]
See Figure 25.
[2]
The wait time specifies the time the power supply must be at levels below 400 mV before ramping up.
tr
VDD
400 mV
0
twait
t = t1
002aag001
Condition: 0 < VI 400 mV at start of power-up (t = t1)
Fig 25. Power-up ramp
10.2 Flash memory
Table 13. Flash characteristics
Tamb = 40 C to +85 C, unless otherwise specified.
Symbol
Parameter
Nendu
endurance
tret
retention time
ter
erase time
tprog
programming time
Conditions
[1]
Min
Typ
Max
Unit
10000
100000
-
cycles
powered
10
-
-
years
unpowered
20
-
-
years
sector or multiple
consecutive sectors
95
100
105
ms
0.95
1
1.05
ms
[2]
[1]
Number of program/erase cycles.
[2]
Programming times are given for writing 256 bytes from RAM to the flash. Data must be written to the flash in blocks of 256 bytes.
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
49 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
10.3 External clock
Table 14. Dynamic characteristic: external clock
Tamb = 40 C to +85 C; VDD over specified ranges.[1]
Min
Typ[2]
Max
Unit
oscillator frequency
1
-
25
MHz
Tcy(clk)
clock cycle time
40
-
1000
ns
tCHCX
clock HIGH time
Tcy(clk) 0.4
-
-
ns
tCLCX
clock LOW time
Tcy(clk) 0.4
-
-
ns
tCLCH
clock rise time
-
-
5
ns
tCHCL
clock fall time
-
-
5
ns
Symbol
Parameter
fosc
Conditions
[1]
Parameters are valid over operating temperature range unless otherwise specified.
[2]
Typical ratings are not guaranteed. The values listed are at room temperature (25 C), nominal supply voltages.
tCHCL
tCHCX
tCLCH
tCLCX
Tcy(clk)
002aaa907
Fig 26. External clock timing (with an amplitude of at least Vi(RMS) = 200 mV)
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
50 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
10.4 Internal oscillators
Table 15. Dynamic characteristics: IRC
Tamb = 40 C to +85 C; 2.7 V VDD 3.6 V[1].
Symbol
Parameter
Conditions
Min
Typ[2]
Max
Unit
fosc(RC)
internal RC oscillator frequency
-
11.88
12
12.12
MHz
[1]
Parameters are valid over operating temperature range unless otherwise specified.
[2]
Typical ratings are not guaranteed. The values listed are at room temperature (25 C), nominal supply voltages.
002aae987
12.15
VDD = 3.6 V
3.3 V
3.0 V
2.7 V
2.4 V
2.0 V
f
(MHz)
12.05
11.95
11.85
−40
−15
10
35
60
85
temperature (°C)
Conditions: Frequency values are typical values. 12 MHz 1 % accuracy is guaranteed for
2.7 V VDD 3.6 V and Tamb = 40 C to +85 C. Variations between parts may cause the IRC to
fall outside the 12 MHz 1 % accuracy specification for voltages below 2.7 V.
Fig 27. Internal RC oscillator frequency f versus temperature
Table 16.
Dynamic characteristics: Watchdog oscillator
Symbol Parameter
fosc(int)
internal oscillator frequency
Min
Typ[1]
Max
Unit
DIVSEL = 0x1F, FREQSEL = 0x1 in the
WDTOSCCTRL register;
[2][3]
-
7.8
-
kHz
DIVSEL = 0x00, FREQSEL = 0xF in the
WDTOSCCTRL register
[2][3]
-
1700
-
kHz
Conditions
[1]
Typical ratings are not guaranteed. The values listed are at nominal supply voltages.
[2]
The typical frequency spread over processing and temperature (Tamb = 40 C to +85 C) is 40 %.
[3]
See the LPC13xx user manual.
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
51 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
10.5 I/O pins
Table 17. Dynamic characteristics: I/O pins[1]
Tamb = 40 C to +85 C; 3.0 V VDD 3.6 V.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
tr
rise time
pin configured as output
3.0
-
5.0
ns
tf
fall time
pin configured as output
2.5
-
5.0
ns
[1]
Applies to standard port pins and RESET pin.
10.6 I2C-bus
Table 18. Dynamic characteristic: I2C-bus pins[1]
Tamb = 40 C to +85 C.[2]
Symbol
Parameter
Conditions
Min
Max
Unit
fSCL
SCL clock
frequency
Standard-mode
0
100
kHz
Fast-mode
0
400
kHz
Fast-mode Plus
0
1
MHz
of both SDA and SCL
signals
-
300
ns
Fast-mode
20 + 0.1 Cb
300
ns
Fast-mode Plus
-
120
ns
Standard-mode
4.7
-
s
Fast-mode
1.3
-
s
Fast-mode Plus
0.5
-
s
Standard-mode
4.0
-
s
Fast-mode
0.6
-
s
Fast-mode Plus
0.26
-
s
Standard-mode
0
-
s
Fast-mode
0
-
s
Fast-mode Plus
0
-
s
fall time
tf
[4][5][6][7]
Standard-mode
tLOW
tHIGH
tHD;DAT
tSU;DAT
LOW period of the
SCL clock
HIGH period of the
SCL clock
data hold time
data set-up time
[3][4][8]
[9][10]
Standard-mode
250
-
ns
Fast-mode
100
-
ns
Fast-mode Plus
50
-
ns
[1]
See the I2C-bus specification UM10204 for details.
[2]
Parameters are valid over operating temperature range unless otherwise specified.
[3]
tHD;DAT is the data hold time that is measured from the falling edge of SCL; applies to data in transmission and the acknowledge.
[4]
A device must internally provide a hold time of at least 300 ns for the SDA signal (with respect to the VIH(min) of the SCL signal) to
bridge the undefined region of the falling edge of SCL.
[5]
Cb = total capacitance of one bus line in pF.
[6]
The maximum tf for the SDA and SCL bus lines is specified at 300 ns. The maximum fall time for the SDA output stage tf is specified at
250 ns. This allows series protection resistors to be connected in between the SDA and the SCL pins and the SDA/SCL bus lines
without exceeding the maximum specified tf.
[7]
In Fast-mode Plus, fall time is specified the same for both output stage and bus timing. If series resistors are used, designers should
allow for this when considering bus timing.
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
52 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
[8]
The maximum tHD;DAT could be 3.45 s and 0.9 s for Standard-mode and Fast-mode but must be less than the maximum of tVD;DAT or
tVD;ACK by a transition time (see UM10204). This maximum must only be met if the device does not stretch the LOW period (tLOW) of the
SCL signal. If the clock stretches the SCL, the data must be valid by the set-up time before it releases the clock.
[9]
tSU;DAT is the data set-up time that is measured with respect to the rising edge of SCL; applies to data in transmission and the
acknowledge.
[10] A Fast-mode I2C-bus device can be used in a Standard-mode I2C-bus system but the requirement tSU;DAT = 250 ns must then be met.
This will automatically be the case if the device does not stretch the LOW period of the SCL signal. If such a device does stretch the
LOW period of the SCL signal, it must output the next data bit to the SDA line tr(max) + tSU;DAT = 1000 + 250 = 1250 ns (according to the
Standard-mode I2C-bus specification) before the SCL line is released. Also the acknowledge timing must meet this set-up time.
tf
SDA
tSU;DAT
70 %
30 %
70 %
30 %
tHD;DAT
tf
70 %
30 %
SCL
tVD;DAT
tHIGH
70 %
30 %
70 %
30 %
70 %
30 %
tLOW
S
1 / fSCL
002aaf425
Fig 28. I2C-bus pins clock timing
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
53 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
10.7 SSP0/1 interface
Remark: The SSP1 interface is available on the LPC1313FBD48/01 only.
Table 19.
Dynamic characteristics: SSP pins in SPI mode
Symbol
Parameter
Conditions
Min
Max
Unit
clock cycle time
full-duplex mode
[1]
40
-
ns
when only transmitting
[1]
27.8
-
ns
in SPI mode;
[2]
15
-
ns
[2]
20
-
ns
SSP master
Tcy(clk)
data set-up time
tDS
2.4 V VDD 3.6 V
2.0 V VDD < 2.4 V
tDH
data hold time
in SPI mode
[2]
0
-
ns
tv(Q)
data output valid time
in SPI mode
[2]
-
10
ns
th(Q)
data output hold time
in SPI mode
[2]
0
-
ns
SSP slave
Tcy(PCLK)
PCLK cycle time
13.9
-
ns
tDS
data set-up time
in SPI mode
[3][4]
0
-
ns
tDH
data hold time
in SPI mode
[3][4]
3 Tcy(PCLK) + 4
-
ns
in SPI mode
[3][4]
-
3 Tcy(PCLK) + 11
ns
in SPI mode
[3][4]
-
2 Tcy(PCLK) + 5
ns
tv(Q)
th(Q)
data output valid time
data output hold time
[1]
Tcy(clk) = (SSPCLKDIV (1 + SCR) CPSDVSR) / fmain. The clock cycle time derived from the SPI bit rate Tcy(clk) is a function of the
main clock frequency fmain, the SSP peripheral clock divider (SSPCLKDIV), the SSP SCR parameter (specified in the SSP0CR0
register), and the SSP CPSDVSR parameter (specified in the SSP clock prescale register).
[2]
Tamb = 40 C to +85 C.
[3]
Tcy(clk) = 12 Tcy(PCLK).
[4]
Tamb = 25 C; VDD = 3.3 V.
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
54 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
Tcy(clk)
tclk(H)
tclk(L)
SCK (CPOL = 0)
SCK (CPOL = 1)
tv(Q)
th(Q)
DATA VALID
MOSI
DATA VALID
tDS
DATA VALID
MISO
tDH
DATA VALID
tv(Q)
MOSI
th(Q)
DATA VALID
DATA VALID
tDH
tDS
MISO
CPHA = 1
DATA VALID
CPHA = 0
DATA VALID
002aae829
Fig 29. SSP master timing in SPI mode
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
55 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
Tcy(clk)
tclk(H)
tclk(L)
tDS
tDH
SCK (CPOL = 0)
SCK (CPOL = 1)
MOSI
DATA VALID
DATA VALID
tv(Q)
MISO
th(Q)
DATA VALID
DATA VALID
tDS
MOSI
DATA VALID
tDH
DATA VALID
tv(Q)
MISO
DATA VALID
CPHA = 1
th(Q)
CPHA = 0
DATA VALID
002aae830
Fig 30. SSP slave timing in SPI mode
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
56 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
10.8 USB interface (LPC1342/43 only)
Table 20. Dynamic characteristics: USB pins (full-speed)
CL = 50 pF; Rpu = 1.5 k on D+ to VDD, unless otherwise specified. 3.0 V VDD 3.6 V
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
tr
rise time
10 % to 90 %
8.5
-
13.8
ns
tf
fall time
10 % to 90 %
7.7
-
13.7
ns
tFRFM
differential rise and fall time
matching
tr / tf
-
-
109
%
VCRS
output signal crossover voltage
1.3
-
2.0
V
tFEOPT
source SE0 interval of EOP
see Figure 31
160
-
175
ns
tFDEOP
source jitter for differential transition
to SE0 transition
see Figure 31
2
-
+5
ns
tJR1
receiver jitter to next transition
18.5
-
+18.5
ns
tJR2
receiver jitter for paired transitions
10 % to 90 %
9
-
+9
ns
tEOPR1
EOP width at receiver
must reject as
EOP; see
Figure 31
[1]
40
-
-
ns
tEOPR2
EOP width at receiver
must accept as
EOP; see
Figure 31
[1]
82
-
-
ns
[1]
Characterized but not implemented as production test. Guaranteed by design.
TPERIOD
crossover point
extended
crossover point
differential
data lines
source EOP width: tFEOPT
differential data to
SE0/EOP skew
n × TPERIOD + tFDEOP
receiver EOP width: tEOPR1, tEOPR2
002aab561
Fig 31. Differential data-to-EOP transition skew and EOP width
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
57 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
11. Application information
11.1 Suggested USB interface solutions (LPC1342/43 only)
VDD
USB_CONNECT
LPC134x
soft-connect switch
R1
1.5 kΩ
USB_VBUS
USB_DP RS = 33 Ω
USB_DM
USB-B
connector
RS = 33 Ω
VSS
002aae608
Fig 32. LPC1342/43 USB interface on a self-powered device
VDD
LPC134x
R1
1.5 kΩ
USB_VBUS
USB_DP RS = 33 Ω
USB-B
connector
USB_DM RS = 33 Ω
VSS
002aae609
Fig 33. LPC1342/43 USB interface on a bus-powered device
11.2 XTAL input
The input voltage to the on-chip oscillators is limited to 1.8 V. If the oscillator is driven by a
clock in slave mode, it is recommended that the input be coupled through a capacitor with
Ci = 100 pF. To limit the input voltage to the specified range, choose an additional
capacitor to ground Cg which attenuates the input voltage by a factor Ci/(Ci + Cg). In slave
mode, a minimum of 200 mV(RMS) is needed.
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
58 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
LPC1xxx
XTALIN
Ci
100 pF
Cg
002aae788
Fig 34. Slave mode operation of the on-chip oscillator
In slave mode the input clock signal should be coupled by means of a capacitor of 100 pF
(Figure 34), with an amplitude between 200 mV(RMS) and 1000 mV(RMS). This
corresponds to a square wave signal with a signal swing of between 280 mV and 1.4 V.
The XTALOUT pin in this configuration can be left unconnected.
External components and models used in oscillation mode are shown in Figure 35 and in
Table 21 and Table 22. Since the feedback resistance is integrated on chip, only a crystal
and the capacitances CX1 and CX2 need to be connected externally in case of
fundamental mode oscillation (the fundamental frequency is represented by L, CL and
RS). Capacitance CP in Figure 35 represents the parallel package capacitance and should
not be larger than 7 pF. Parameters FOSC, CL, RS and CP are supplied by the crystal
manufacturer.
LPC1xxx
L
XTALIN
XTALOUT
=
CL
CP
XTAL
RS
CX1
CX2
002aaf424
Fig 35. Oscillator modes and models: oscillation mode of operation and external crystal
model used for CX1/CX2 evaluation
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
59 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
Table 21.
Recommended values for CX1/CX2 in oscillation mode (crystal and external
components parameters) low frequency mode
Fundamental oscillation
frequency FOSC
Crystal load
capacitance CL
Maximum crystal
series resistance RS
External load
capacitors CX1, CX2
1 MHz - 5 MHz
10 pF
< 300
18 pF, 18 pF
20 pF
< 300
39 pF, 39 pF
30 pF
< 300
57 pF, 57 pF
10 pF
< 300
18 pF, 18 pF
20 pF
< 200
39 pF, 39 pF
30 pF
< 100
57 pF, 57 pF
10 MHz - 15 MHz
10 pF
< 160
18 pF, 18 pF
20 pF
< 60
39 pF, 39 pF
15 MHz - 20 MHz
10 pF
< 80
18 pF, 18 pF
5 MHz - 10 MHz
Table 22.
Recommended values for CX1/CX2 in oscillation mode (crystal and external
components parameters) high frequency mode
Fundamental oscillation
frequency FOSC
Crystal load
capacitance CL
Maximum crystal
series resistance RS
External load
capacitors CX1, CX2
15 MHz - 20 MHz
10 pF
< 180
18 pF, 18 pF
20 pF
< 100
39 pF, 39 pF
10 pF
< 160
18 pF, 18 pF
20 pF
< 80
39 pF, 39 pF
20 MHz - 25 MHz
11.3 XTAL Printed-Circuit Board (PCB) layout guidelines
The crystal should be connected on the PCB as close as possible to the oscillator input
and output pins of the chip. Take care that the load capacitors Cx1, Cx2, and Cx3 in case of
third overtone crystal usage have a common ground plane. The external components
must also be connected to the ground plain. Loops must be made as small as possible in
order to keep the noise coupled in via the PCB as small as possible. Also parasitics
should stay as small as possible. Values of Cx1 and Cx2 should be chosen smaller
accordingly to the increase in parasitics of the PCB layout.
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
60 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
11.4 Standard I/O pad configuration
Figure 36 shows the possible pin modes for standard I/O pins with analog input function:
•
•
•
•
•
Digital output driver
Digital input: Pull-up enabled/disabled
Digital input: Pull-down enabled/disabled
Digital input: Repeater mode enabled/disabled
Analog input
VDD
ESD
output enable
pin configured
as digital output
driver
output
PIN
ESD
VDD
VSS
weak
pull-up
pull-up enable
pin configured
as digital input
weak
pull-down
repeater mode
enable
pull-down enable
data input
select analog input
pin configured
as analog input
analog input
002aaf304
Fig 36. Standard I/O pad configuration
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
61 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
11.5 Reset pad configuration
VDD
VDD
VDD
Rpu
ESD
20 ns RC
GLITCH FILTER
reset
PIN
ESD
VSS
002aaf274
Fig 37. Reset pad configuration
11.6 ADC usage notes
The following guidelines show how to increase the performance of the ADC in a noisy
environment beyond the ADC specifications listed in Table 8:
• The ADC input trace must be short and as close as possible to the LPC1311/13/42/43
chip.
• The ADC input traces must be shielded from fast switching digital signals and noisy
power supply lines.
• Because the ADC and the digital core share the same power supply, the power supply
line must be adequately filtered.
• To improve the ADC performance in a very noisy environment, put the device in Sleep
mode during the ADC conversion.
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
62 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
11.7 ElectroMagnetic Compatibility (EMC)
Radiated emission measurements according to the IEC61967-2 standard using the
TEM-cell method are shown for the LPC1343FBD48 in Table 23.
Table 23. ElectroMagnetic Compatibility (EMC) for part LPC1343FBD48 (TEM-cell method)
VDD = 3.3 V; Tamb = 25 C.
Parameter
Frequency band
System clock =
Unit
12 MHz
24 MHz
48 MHz
72 MHz
150 kHz - 30 MHz
6
5
7
7
dBV
30 MHz - 150 MHz
1
+3
+9
+13
dBV
150 MHz - 1 GHz
+3
+7
+15
+19
dBV
-
O
N
M
L
-
Input clock: IRC (12 MHz)
maximum
peak level
IEC
level[1]
Input clock: crystal oscillator (12 MHz)
maximum
peak level
IEC level[1]
[1]
LPC1311_13_42_43
Product data sheet
150 kHz - 30 MHz
-5
5
7
7
dBV
30 MHz - 150 MHz
0
+4
+9
+13
dBV
150 MHz - 1 GHz
3
+8
+15
+20
dBV
-
O
N
M
L
-
IEC levels refer to Appendix D in the IEC61967-2 Specification.
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
63 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
12. Package outline
LQFP48: plastic low profile quad flat package; 48 leads; body 7 x 7 x 1.4 mm
SOT313-2
c
y
X
36
25
A
37
24
ZE
e
E HE
A A2
(A 3)
A1
w M
θ
bp
pin 1 index
Lp
L
13
48
detail X
12
1
ZD
e
v M A
w M
bp
D
B
HD
v M B
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (1)
e
HD
HE
L
Lp
v
w
y
mm
1.6
0.20
0.05
1.45
1.35
0.25
0.27
0.17
0.18
0.12
7.1
6.9
7.1
6.9
0.5
9.15
8.85
9.15
8.85
1
0.75
0.45
0.2
0.12
0.1
Z D (1) Z E (1)
θ
0.95
0.55
7o
o
0
0.95
0.55
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
SOT313-2
136E05
MS-026
JEITA
EUROPEAN
PROJECTION
ISSUE DATE
00-01-19
03-02-25
Fig 38. Package outline SOT313-2 (LQFP48)
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
64 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
HVQFN33: plastic thermal enhanced very thin quad flat package; no leads;
33 terminals; body 7 x 7 x 0.85 mm
A
B
D
terminal 1
index area
E
A
A1
c
detail X
e1
e
9
16
C
C A B
C
v
w
b
y
y1 C
L
8
17
e
e2
Eh
33
1
terminal 1
index area
24
32
X
25
Dh
0
2.5
scale
Dimensions
Unit
mm
5 mm
A(1)
A1
b
max 1.00 0.05 0.35
nom 0.85 0.02 0.28
min 0.80 0.00 0.23
c
D(1)
Dh
E(1)
0.2
7.1
7.0
6.9
4.85
4.70
4.55
7.1
7.0
6.9
Eh
e
e1
e2
L
0.75
4.85
4.70 0.65 4.55 4.55 0.60
0.45
4.55
v
0.1
w
y
0.05 0.08
y1
0.1
Note
1. Plastic or metal protrusions of 0.075 mm maximum per side are not included.
Outline
version
References
IEC
JEDEC
JEITA
---
hvqfn33_po
European
projection
Issue date
09-03-17
09-03-23
Fig 39. Package outline (HVQFN33)
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
65 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
13. Soldering
Footprint information for reflow soldering of LQFP48 package
SOT313-2
Hx
Gx
P2
Hy
(0.125)
P1
Gy
By
Ay
C
D2 (8×)
D1
Bx
Ax
Generic footprint pattern
Refer to the package outline drawing for actual layout
solder land
occupied area
DIMENSIONS in mm
P1
P2
0.500
0.560
Ax
Ay
10.350 10.350
Bx
By
C
D1
D2
Gx
7.350
7.350
1.500
0.280
0.500
7.500
Gy
Hx
Hy
7.500 10.650 10.650
sot313-2_fr
Fig 40. Reflow soldering of the LQFP48 package
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
66 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
Footprint information for reflow soldering of HVQFN33 package
OID = 8.20 OA
PID = 7.25 PA+OA
OwDtot = 5.10 OA
evia = 4.25
0.20 SR
chamfer (4×)
W = 0.30 CU
SPD = 1.00 SP
LaE = 7.95 CU
PIE = 7.25 PA+OA
LbE = 5.80 CU
evia = 4.25
evia = 1.05
0.45 DM
SPE = 1.00 SP
GapE = 0.70 SP
4.55 SR
SEhtot = 2.70 SP
EHS = 4.85 CU
OwEtot = 5.10 OA
OIE = 8.20 OA
e = 0.65
0.45 DM
GapD = 0.70 SP
evia = 2.40
B-side
SDhtot = 2.70 SP
4.55 SR
DHS = 4.85 CU
Solder resist
covered via
0.30 PH
LbD = 5.80 CU
0.60 SR cover
LaD = 7.95 CU
0.60 CU
(A-side fully covered)
number of vias: 20
solder land
solder land plus solder paste
solder paste deposit
solder resist
occupied area
Dimensions in mm
Remark:
Stencil thickness: 0.125 mm
001aao134
Fig 41. Reflow soldering of the HVQFN33 package
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
67 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
14. Abbreviations
Table 24.
LPC1311_13_42_43
Product data sheet
Abbreviations
Acronym
Description
A/D
Analog-to-Digital
ADC
Analog-to-Digital Converter
AHB
Advanced High-performance Bus
AMBA
Advanced Microcontroller Bus Architecture
APB
Advanced Peripheral Bus
BOD
BrownOut Detection
EOP
End Of Packet
ETM
Embedded Trace Macrocell
FIFO
First-In, First-Out
GPIO
General Purpose Input/Output
HID
Human Interface Device
I/O
Input/Output
LSB
Least Significant Bit
MSC
Mass Storage Class
PHY
Physical Layer
PLL
Phase-Locked Loop
SE0
Single Ended Zero
SPI
Serial Peripheral Interface
SSI
Serial Synchronous Interface
SSP
Synchronous Serial Port
SoF
Start-of-Frame
TCM
Tightly-Coupled Memory
TTL
Transistor-Transistor Logic
UART
Universal Asynchronous Receiver/Transmitter
USB
Universal Serial Bus
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
68 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
15. Revision history
Table 25.
Revision history
Document ID
Release date
Data sheet status
Change notice Supersedes
LPC1311_13_42_43 v.4
20110620
Product data sheet
-
Modifications:
•
•
LPC1311_13_42_43 v.3
Parts LPC1311/01 and LPC1313/01 added (LPC1300L series).
Modifications to the data sheet applying to the LPC1311/01 and LPC1313/01 only:
– Power consumption added in Table 7 and Section 9.4.
– Power profiles added to Section 2 and in Section 7.18.5.1.
– SSP1 added for LPC1313FBD48/01.
– BOD forced reset supports four levels (see Table 10).
– WWDT added for parts LPC1311/01 and LPC1313/01.
– Function DTR added to pin PIO3_0, function DSR added to PIO3_1, function DCD
added to PIO3_2, and function RI added to PIO3_3 in Table 3 (LPC1300L series
only).
•
•
•
•
•
•
•
Parameter Vhys for I2C bus pins: typical value corrected Vhys = 0.05VDD in Table 7.
Typical value for parameter Nendu added in Table 13 “Flash characteristics”.
PLL output frequency limited to 100 MHz in Section 7.18.2.
Description of RESET and WAKEUP functions updated in Section 7.19.
WDT description updated in Section 7.14. The WDT is a 24-bit timer.
Parameter VOL removed for I2C-bus pins in Table 7 and replaced by parameter IOL.
Specify 3.0 V VDD 3.6 V for USB pins in Table 7 (Table note 2 and Table note 17)
and in Table 20.
•
Table note for pins USB_DM and USB_DP updated: pads are not 5 V tolerant (Table 3
and Table 4).
•
•
•
Updated parameters VOH and IOH for PIO0_7 in Table 7.
•
•
•
•
•
Reflow soldering footprint drawings added in Section 13.
Section 11.7 “ElectroMagnetic Compatibility (EMC)” added.
Internal pull-up specified for LPC1311/13/42/43 and LPC1311/01 and LPC1313/01 in
Table 3 (Table note 1) and Table 4 (Table note 1).
ADC sampling frequency corrected in Table 8 (Table note 7).
Power-up characterization added (Section 10.1).
Condition for parameter Tstg in Table 6 updated.
Table note 4 of Table 6 updated.
LPC1311_13_42_43 v.3
20100810
Product data sheet
-
LPC1311_13_42_43 v.2
LPC1311_13_42_43 v.2
20100506
Product data sheet
-
LPC1311_13_42_43 v.1
LPC1311_13_42_43 v.1
20091211
Product data sheet
-
-
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
69 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
16. Legal information
16.1 Data sheet status
Document status[1][2]
Product status[3]
Definition
Objective [short] data sheet
Development
This document contains data from the objective specification for product development.
Preliminary [short] data sheet
Qualification
This document contains data from the preliminary specification.
Product [short] data sheet
Production
This document contains the product specification.
[1]
Please consult the most recently issued document before initiating or completing a design.
[2]
The term ‘short data sheet’ is explained in section “Definitions”.
[3]
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
16.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
16.3 Disclaimers
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors accepts no liability for inclusion and/or use of
NXP Semiconductors products in such equipment or applications and
therefore such inclusion and/or use is at the customer’s own risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the customer’s applications and
products planned, as well as for the planned application and use of
customer’s third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in life support, life-critical or
safety-critical systems or equipment, nor in applications where failure or
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from national authorities.
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
70 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
Non-automotive qualified products — Unless this data sheet expressly
states that this specific NXP Semiconductors product is automotive qualified,
the product is not suitable for automotive use. It is neither qualified nor tested
in accordance with automotive testing or application requirements. NXP
Semiconductors accepts no liability for inclusion and/or use of
non-automotive qualified products in automotive equipment or applications.
In the event that customer uses the product for design-in and use in
automotive applications to automotive specifications and standards, customer
(a) shall use the product without NXP Semiconductors’ warranty of the
product for such automotive applications, use and specifications, and (b)
whenever customer uses the product for automotive applications beyond
NXP Semiconductors’ specifications such use shall be solely at customer’s
own risk, and (c) customer fully indemnifies NXP Semiconductors for any
liability, damages or failed product claims resulting from customer design and
use of the product for automotive applications beyond NXP Semiconductors’
standard warranty and NXP Semiconductors’ product specifications.
16.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
I2C-bus — logo is a trademark of NXP B.V.
17. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
71 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
18. Contents
1
2
3
4
4.1
5
6
6.1
6.2
7
7.1
7.2
7.3
7.4
7.5
7.6
General description . . . . . . . . . . . . . . . . . . . . . . 1
Features and benefits . . . . . . . . . . . . . . . . . . . . 1
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Ordering information . . . . . . . . . . . . . . . . . . . . . 3
Ordering options . . . . . . . . . . . . . . . . . . . . . . . . 3
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Pinning information . . . . . . . . . . . . . . . . . . . . . . 6
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Pin description . . . . . . . . . . . . . . . . . . . . . . . . 10
Functional description . . . . . . . . . . . . . . . . . . 17
Architectural overview . . . . . . . . . . . . . . . . . . 17
ARM Cortex-M3 processor . . . . . . . . . . . . . . . 17
On-chip flash program memory . . . . . . . . . . . 17
On-chip SRAM . . . . . . . . . . . . . . . . . . . . . . . . 17
Memory map. . . . . . . . . . . . . . . . . . . . . . . . . . 17
Nested Vectored Interrupt Controller
(NVIC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
7.6.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7.6.2
Interrupt sources. . . . . . . . . . . . . . . . . . . . . . . 19
7.7
IOCONFIG block . . . . . . . . . . . . . . . . . . . . . . 19
7.8
Fast general purpose parallel I/O . . . . . . . . . . 19
7.8.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7.9
USB interface (LPC1342/43 only) . . . . . . . . . 20
7.9.1
Full-speed USB device controller . . . . . . . . . . 20
7.9.1.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
7.10
UART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7.10.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7.11
SSP serial I/O controller . . . . . . . . . . . . . . . . . 21
7.11.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7.12
I2C-bus serial I/O controller . . . . . . . . . . . . . . 21
7.12.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.13
10-bit ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.13.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.14
General purpose external event
counter/timers . . . . . . . . . . . . . . . . . . . . . . . . . 23
7.14.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
7.15
System tick timer . . . . . . . . . . . . . . . . . . . . . . 23
7.16
Watchdog timer. . . . . . . . . . . . . . . . . . . . . . . . 23
7.16.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
7.17
Windowed WatchDog Timer (WWDT) . . . . . . 24
7.17.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
7.18
Clocking and power control . . . . . . . . . . . . . . 24
7.18.1
Integrated oscillators . . . . . . . . . . . . . . . . . . . 24
7.18.1.1 Internal RC oscillator . . . . . . . . . . . . . . . . . . . 25
7.18.1.2 System oscillator . . . . . . . . . . . . . . . . . . . . . . 26
7.18.1.3 Watchdog oscillator . . . . . . . . . . . . . . . . . . . . 26
7.18.2
System PLL and USB PLL . . . . . . . . . . . . . . . 26
7.18.3
7.18.4
7.18.5
7.18.5.1
Clock output . . . . . . . . . . . . . . . . . . . . . . . . . .
Wake-up process . . . . . . . . . . . . . . . . . . . . . .
Power control . . . . . . . . . . . . . . . . . . . . . . . . .
Power profiles (LPC1300L series,
LPC1311/01 and LPC1313/01 only) . . . . . . .
7.18.5.2 Sleep mode . . . . . . . . . . . . . . . . . . . . . . . . . .
7.18.5.3 Deep-sleep mode. . . . . . . . . . . . . . . . . . . . . .
7.18.5.4 Deep power-down mode . . . . . . . . . . . . . . . .
7.19
System control . . . . . . . . . . . . . . . . . . . . . . . .
7.19.1
Start logic . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.19.2
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.19.3
Brownout detection . . . . . . . . . . . . . . . . . . . .
7.19.4
Code security
(Code Read Protection - CRP) . . . . . . . . . . .
7.19.5
Boot loader. . . . . . . . . . . . . . . . . . . . . . . . . . .
7.19.6
APB interface . . . . . . . . . . . . . . . . . . . . . . . . .
7.19.7
AHB-Lite . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.19.8
External interrupt inputs . . . . . . . . . . . . . . . . .
7.19.9
Memory mapping control . . . . . . . . . . . . . . . .
7.20
Emulation and debugging . . . . . . . . . . . . . . .
8
Limiting values . . . . . . . . . . . . . . . . . . . . . . . .
9
Static characteristics . . . . . . . . . . . . . . . . . . .
9.1
BOD static characteristics for
LPC1300 series . . . . . . . . . . . . . . . . . . . . . . .
9.2
BOD static characteristics for
LPC1300L series (LPC1311/01 and
LPC1313/01) . . . . . . . . . . . . . . . . . . . . . . . . .
9.3
Power consumption for LPC1300 series . . . .
9.4
Power consumption for LPC1300L series
(LPC1311/01 and LPC1313/01) . . . . . . . . . . .
9.5
Peripheral power consumption . . . . . . . . . . .
9.6
Electrical pin characteristics. . . . . . . . . . . . . .
10
Dynamic characteristics. . . . . . . . . . . . . . . . .
10.1
Power-up ramp conditions . . . . . . . . . . . . . . .
10.2
Flash memory . . . . . . . . . . . . . . . . . . . . . . . .
10.3
External clock. . . . . . . . . . . . . . . . . . . . . . . . .
10.4
Internal oscillators . . . . . . . . . . . . . . . . . . . . .
10.5
I/O pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.6
I2C-bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.7
SSP0/1 interface . . . . . . . . . . . . . . . . . . . . . .
10.8
USB interface (LPC1342/43 only) . . . . . . . . .
11
Application information . . . . . . . . . . . . . . . . .
11.1
Suggested USB interface solutions
(LPC1342/43 only) . . . . . . . . . . . . . . . . . . . . .
11.2
XTAL input . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.3
XTAL Printed-Circuit Board (PCB) layout
guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . .
26
26
27
27
27
27
28
28
28
28
28
28
29
29
29
29
29
30
31
32
37
38
38
41
44
45
49
49
49
50
51
52
52
54
57
58
58
58
60
continued >>
LPC1311_13_42_43
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 20 June 2011
© NXP B.V. 2011. All rights reserved.
72 of 73
LPC1311/13/42/43
NXP Semiconductors
32-bit ARM Cortex-M3 microcontroller
11.4
11.5
11.6
11.7
12
13
14
15
16
16.1
16.2
16.3
16.4
17
18
Standard I/O pad configuration . . . . . . . . . . . .
Reset pad configuration . . . . . . . . . . . . . . . . .
ADC usage notes . . . . . . . . . . . . . . . . . . . . . .
ElectroMagnetic Compatibility (EMC) . . . . . . .
Package outline . . . . . . . . . . . . . . . . . . . . . . . .
Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . .
Revision history . . . . . . . . . . . . . . . . . . . . . . . .
Legal information. . . . . . . . . . . . . . . . . . . . . . .
Data sheet status . . . . . . . . . . . . . . . . . . . . . .
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact information. . . . . . . . . . . . . . . . . . . . .
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
61
62
62
63
64
66
68
69
70
70
70
70
71
71
72
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2011.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
Date of release: 20 June 2011
Document identifier: LPC1311_13_42_43