INTEGRATED CIRCUITS 74F64 4-2-3-2-input AND-OR-invert gate Product specification IC15 Data Handbook 1996 Mar 14 Philips Semiconductors Product specification 4-2-3-2-input AND-OR-invert gate TYPE TYPICAL PROPAGATION DELAY TYPICAL SUPPLY CURRENT (TOTAL) 74F64 4.0ns 2.5mA 74F64 PIN CONFIGURATION ORDERING INFORMATION COMMERCIAL RANGE VCC = 5V ±10%, Tamb = 0°C to +70°C DESCRIPTION Dc 1 14 VCC Da 2 13 Dd Db 3 12 De Dg 4 11 Df Dh 5 10 Dk Di 6 9 Dj GND 7 8 Q PKG. DWG. # 14-pin plastic DIP N74F64N SOT27-1 14-pin plastic SO N74F64D SOT108-1 SF00094 INPUT AND OUTPUT LOADING AND FAN-OUT TABLE PINS DESCRIPTION 74F (U.L.) HIGH/LOW LOAD VALUE HIGH/LOW Dn Data inputs 1.0/1.0 20µA/0.6mA Q Data output 50/33 1.0mA/20mA NOTE: One (1.0) FAST unit load is defined as: 20µA in the High state and 0.6mA in the Low state. LOGIC SYMBOL IEC/IEEE SYMBOL 2 2 3 1 13 12 11 4 5 6 9 & 1 3 10 1 & 13 12 Da Db Dc Dd De Df Dg Dh Di Dj Dk 11 4 Q 8 & 5 6 9 8 & 10 VCC = Pin 14 GND = Pin 7 SF00095 1996 Mar 14 SF00096 2 853–0334 16574 Philips Semiconductors Product specification 4-2-3-2-input AND-OR-invert gate 74F64 LOGIC DIAGRAM Da Db Dc Dd De Df Dg Dh Di Dj Dk 2 3 1 13 12 11 8 Q 4 5 6 9 10 VCC = Pin 14 GND = Pin 7 SF00097 FUNCTION TABLE INPUTS OUTPUT Da Db Dc Dd De Df Dg Dh Di Dj Dk Q H H X X X X X X X X X L X X H H H H X X X X X L X X X X X X H H H X X L X X X X X X X X X H H All other combinations L H NOTES: 1. H = High voltage level 2. L = Low voltage level 3. X = Don’t care ABSOLUTE MAXIMUM RATINGS (Operation beyond the limits set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free-air temperature range.) SYMBOL PARAMETER RATING UNIT VCC Supply voltage –0.5 to +7.0 V VIN Input voltage –0.5 to +7.0 V IIN Input current –30 to +5 mA VOUT Voltage applied to output in High output state –0.5 to VCC V IOUT Current applied to output in Low output state Tamb Operating free-air temperature range Tstg Storage temperature range 1996 Mar 14 3 40 mA 0 to +70 °C –65 to +150 °C Philips Semiconductors Product specification 4-2-3-2-input AND-OR-invert gate 74F64 RECOMMENDED OPERATING CONDITIONS LIMITS SYMBOL PARAMETER UNIT MIN NOM MAX 5.0 5.5 VCC Supply voltage 4.5 V VIH High-level input voltage 2.0 VIL Low-level input voltage 0.8 V IIK Input clamp current –18 mA IOH High-level output current –1 mA IOL Low-level output current 20 mA Tamb Operating free-air temperature range +70 °C V 0 DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) SYMBOL TEST CONDITIONS1 PARAMETER LIMITS MIN TYP2 MAX UNIT VCC = MIN, VIL = MAX ±10%VCC 2.5 VIH = MIN, IOH = MAX ±5%VCC 2.7 VCC = MIN, VIL = MAX ±10%VCC 0.30 0.50 V VIH = MIN, IOL = MAX ±5%VCC 0.30 0.50 V –0.73 –1.2 V VCC = MAX, VI = 7.0V 100 µA High-level input current VCC = MAX, VI = 2.7V 20 µA IIL Low-level input current VCC = MAX, VI = 0.5V IOS Short-circuit output current3 VCC = MAX ICC Supply current (total) VOH O High level output voltage High-level VOL O Low level output voltage Low-level VIK Input clamp voltage VCC = MIN, II = IIK II Input current at maximum input voltage IIH ICCH –60 VCC = MAX V –0.6 mA –150 mA mA VIN = GND 1.9 2.8 VIN = 4.5V 3.1 4.7 mA NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25°C. 3. Not more than one output should be shorted at a time. For testing IOS, the use of high-speed test apparatus and/or sample-and-hold techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting of a High output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any sequence of parameter tests, IOS tests should be performed last. 1996 Mar 14 ICCL V 3.4 4 Philips Semiconductors Product specification 4-2-3-2-input AND-OR-invert gate 74F64 AC ELECTRICAL CHARACTERISTICS LIMITS SYMBOL tPLH tPHL TEST CONDITION PARAMETER Propagation delay Dn to Q VCC = +5.0V ± 10% Tamb = 0°C to +70°C CL = 50pF, RL = 500Ω VCC = +5.0V Tamb = +25°C CL = 50pF, RL = 500Ω Waveform 1 MIN TYP MAX MIN MAX 2.5 2.0 4.6 3.2 6.0 4.5 2.5 2.0 7.0 5.5 UNIT ns AC WAVEFORMS For all waveforms, VM = 1.5V. Dn VM VM tPHL tPLH VM Q VM SF00098 Waveform 1. Propagation Delay for Inverting Outputs TEST CIRCUIT AND WAVEFORM VCC VIN tw 90% NEGATIVE PULSE VM D.U.T. RT CL RL AMP (V) VM 10% VOUT PULSE GENERATOR 90% 10% tTHL (tf ) tTLH (tr ) tTLH (tr ) tTHL (tf ) 0V AMP (V) 90% 90% POSITIVE PULSE DEFINITIONS: RL = Load resistor; see AC ELECTRICAL CHARACTERISTICS for value. CL = Load capacitance includes jig and probe capacitance; see AC ELECTRICAL CHARACTERISTICS for value. RT = Termination resistance should be equal to ZOUT of pulse generators. VM VM 10% Test Circuit for Totem-Pole Outputs 10% tw 0V Input Pulse Definition INPUT PULSE REQUIREMENTS family amplitude VM 74F 3.0V 1.5V rep. rate tw tTLH tTHL 1MHz 500ns 2.5ns 2.5ns SF00006 1996 Mar 14 5 Philips Semiconductors Product specification 4-2-3-2 Input AND-OR Invert Gate 74F64 DIP14: plastic dual in-line package; 14 leads (300 mil) 1996 Mar 14 6 SOT27-1 Philips Semiconductors Product specification 4-2-3-2 Input AND-OR Invert Gate 74F64 SO14: plastic small outline package; 14 leads; body width 3.9 mm 1996 Mar 14 7 SOT108-1 Philips Semiconductors Product specification 4-2-3-2-input AND-OR-invert gate 74F64 DEFINITIONS Data Sheet Identification Product Status Definition Objective Specification Formative or in Design This data sheet contains the design target or goal specifications for product development. Specifications may change in any manner without notice. Preliminary Specification Preproduction Product This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Product Specification Full Production This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes at any time without notice, in order to improve design and supply the best possible product. Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. LIFE SUPPORT APPLICATIONS Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices, or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale. Philips Semiconductors 811 East Arques Avenue P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381 Philips Semiconductors and Philips Electronics North America Corporation register eligible circuits under the Semiconductor Chip Protection Act. Copyright Philips Electronics North America Corporation 1996 All rights reserved. Printed in U.S.A.