34.807IRELESS IMPORTANT NOTICE Dear customer, As from August 2nd 2008, the wireless operations of NXP have moved to a new company, ST-NXP Wireless. As a result, the following changes are applicable to the attached document. ● Company name - NXP B.V. is replaced with ST-NXP Wireless. ● Copyright - the copyright notice at the bottom of each page “© NXP B.V. 200x. All rights reserved”, shall now read: “© ST-NXP Wireless 200x - All rights reserved”. ● Web site - http://www.nxp.com is replaced with http://www.stnwireless.com ● Contact information - the list of sales offices previously obtained by sending an email to [email protected] , is now found at http://www.stnwireless.com under Contacts. If you have any questions related to the document, please contact our nearest sales office. Thank you for your cooperation and understanding. ST-NXP Wireless 34.807IRELESS www.stnwireless.com ISP1582 Hi-Speed USB peripheral controller Rev. 07 — 22 September 2008 Product data sheet 1. General description The ISP1582 is a cost-optimized and feature-optimized Hi-Speed Universal Serial Bus (USB) peripheral controller. It fully complies with Ref. 1 “Universal Serial Bus Specification Rev. 2.0”, supporting data transfer at high-speed (480 Mbit/s) and full-speed (12 Mbit/s). The ISP1582 provides high-speed USB communication capacity to systems based on microcontrollers or microprocessors. It communicates with a microcontroller or microprocessor of a system through a high-speed general-purpose parallel interface. The ISP1582 supports automatic detection of Hi-Speed USB system operation. Original USB fall-back mode allows the device to remain operational under full-speed conditions. It is designed as a generic USB peripheral controller so that it can fit into all existing device classes, such as imaging class, mass storage devices, communication devices, printing devices and human interface devices. The internal generic Direct Memory Access (DMA) block allows easy integration into data streaming applications. The modular approach to implementing a USB peripheral controller allows the designer to select the optimum system microcontroller from the wide variety available. The ability to reuse existing architecture and firmware shortens the development time, eliminates risk and reduces cost. The result is fast and efficient development of the most cost-effective USB peripheral solution. The ISP1582 also incorporates features such as SoftConnect, a reduced frequency crystal oscillator, and integrated termination resistors. These features allow significant cost savings in system design and easy implementation of advanced USB functionality into PC peripherals. 2. Features n Complies fully with: u Ref. 1 “Universal Serial Bus Specification Rev. 2.0” u Most device class specifications u ACPI, OnNow and USB power management requirements n Supports data transfer at high-speed (480 Mbit/s) and full-speed (12 Mbit/s) n High performance USB peripheral controller with integrated Serial Interface Engine (SIE), Parallel Interface Engine (PIE), FIFO memory and data transceiver n Automatic Hi-Speed USB mode detection and Original USB fall-back mode n Supports sharing mode n Supports VBUS sensing n Supports Generic DMA (GDMA) slave mode ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller n n n n n n n n n n n n n n n High-speed DMA interface Fully autonomous and multi-configuration DMA operation Seven IN endpoints, seven OUT endpoints, and a fixed control IN and OUT endpoint Integrated physical 8 kB of multi-configuration FIFO memory Endpoints with double buffering to increase throughput and ease real-time data transfer Bus-independent interface with most microcontrollers and microprocessors 12 MHz crystal oscillator with integrated PLL for low EMI Software-controlled connection to the USB bus (SoftConnect) Low-power consumption in operation and power-down modes; suitable for use in bus-powered USB devices Supports Session Request Protocol (SRP) that adheres to Ref. 2 “On-The-Go Supplement to the USB Specification Rev. 1.3” Internal power-on and low-voltage reset circuits; also supports software reset Operation over the extended USB bus voltage range (DP, DM and VBUS) 5 V tolerant I/O pads Operating temperature range from −40 °C to +85 °C Available in HVQFN56 halogen-free and lead-free package 3. Applications n n n n n n n n Personal digital assistant Digital video camera Digital still camera 3G mobile phone MP3 player Communication device, for example: router and modem Printer Scanner 4. Ordering information Table 1. Ordering information Type number ISP1582BS Package Name Description Version HVQFN56 plastic thermal enhanced very thin quad flat package; no leads; 56 terminals; body 8 × 8 × 0.85 mm SOT684-1 ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 2 of 68 xxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx x xxxxxxxxxxxxxx xxxxxxxxxx xxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxx xx xxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxx xxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxx xxxxxxxxxxxxxx xxxxxx xx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxx xxxxx x x 3.3 V 4 49 XTAL1 XTAL2 52 51 Rev. 07 — 22 September 2008 RREF DMA HANDLER SoftConnect 2 6 HI-SPEED USB TRANSCEIVER NXP SIE/PIE 12.0 kΩ RESET_N 9 ISP1582 1.5 kΩ RPU 7 POWER-ON RESET DIOR DACK MEMORY MANAGEMENT UNIT 10 DIOW 11 12 8 30 to 33, 35 to 40, 42 to 47 16 DATA [15:0] DMA REGISTERS 18 to 20, 22 to 25, 27 8 internal reset INTEGRATED RAM (8 kB) MICROCONTROLLER HANDLER analog supply 53, 54 MICROCONTROLLER INTERFACE A[7:0] 15 VOLTAGE REGULATORS 17 digital supply SYSTEM CONTROLLER OTG SRP MODULE 14 I/O pad supply 13, 26, 29, 41 1, 5 28, 50 56 55 21, 34, 48 004aaa199 DGND AGND Block diagram SUSPEND WAKEUP VCC(I/O) RD_N WR_N INT ISP1582 3 of 68 © NXP B.V. 2008. All rights reserved. Fig 1. VCC1V8 CS_N Hi-Speed USB peripheral controller 3.3 V EOT DMA INTERFACE 16 VCC NXP Semiconductors 3 DREQ VBUS 5. Block diagram ISP1582_7 Product data sheet 12 MHz to or from USB DP DM ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller 6. Pinning information 43 DATA11 44 DATA12 45 DATA13 46 DATA14 47 DATA15 48 VCC(I/O) 49 VBUS 50 VCC1V8 51 XTAL2 52 XTAL1 53 VCC 54 VCC terminal 1 index area 55 WAKEUP 56 SUSPEND 6.1 Pinning AGND 1 42 DATA10 RPU 2 41 DGND DP 3 40 DATA9 DM 4 39 DATA8 AGND 5 38 DATA7 RREF 6 37 DATA6 RESET_N 7 EOT 8 DREQ 9 36 DATA5 ISP1582BS 35 DATA4 DACK 10 34 VCC(I/O) 33 DATA3 VCC1V8 28 A7 27 DGND 26 A6 25 A5 24 A4 23 A3 22 VCC(I/O) 21 A2 20 A1 19 29 DGND A0 18 30 DATA0 INT 14 WR_N 17 31 DATA1 DGND 13 CS_N 15 32 DATA2 RD_N 16 DIOR 11 DIOW 12 004aaa536 Transparent top view Fig 2. Pin configuration HVQFN56 (top view) 6.2 Pin description Table 2. Symbol[1] Pin description Pin Type[2] Description AGND 1 - analog ground RPU 2 A pull-up resistor connection; connect to the external pull-up resistor for pin DP; must be connected to 3.3 V through a 1.5 kΩ resistor DP 3 A USB D+ line connection (analog) DM 4 A USB D− line connection (analog) AGND 5 - analog ground RREF 6 A external bias resistor connection; connect to the external bias resistor; must be connected to ground through a 12.0 kΩ ± 1 % resistor ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 4 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Table 2. Pin description …continued Symbol[1] Pin Type[2] Description RESET_N 7 I reset input (500 µs); a LOW level produces an asynchronous reset; connect to VCC for power-on reset (internal POR circuit) When the RESET_N pin is LOW, ensure that the WAKEUP pin does not go from LOW to HIGH; otherwise the device will enter test mode. TTL; 5 V tolerant EOT 8 I end-of-transfer input (programmable polarity); when not in use, connect this pin to VCC(I/O) through a 10 kΩ resistor DREQ 9 O DMA request (programmable polarity) output; when not in use, connect this pin to ground through a 10 kΩ resistor; see Table 51 and Table 52 input pad; TTL; 5 V tolerant TTL; 4 ns slew-rate control DACK 10 I DMA acknowledge input (programmable polarity); when not in use, connect this pin to VCC(I/O) through a 10 kΩ resistor; see Table 51 and Table 52 TTL; 5 V tolerant DIOR 11 I DMA read strobe input (programmable polarity); when not in use, connect this pin to VCC(I/O) through a 10 kΩ resistor; see Table 51 and Table 52 TTL; 5 V tolerant DIOW 12 I DMA write strobe input (programmable polarity); when not in use, connect this pin to VCC(I/O) through a 10 kΩ resistor; see Table 51 and Table 52 DGND 13 - digital ground INT 14 O interrupt output; programmable polarity (active HIGH or LOW) and signaling (edge or level triggered) TTL; 5 V tolerant CMOS output; 8 mA drive CS_N 15 I chip select input RD_N 16 I read strobe input input pad; TTL; 5 V tolerant input pad; TTL; 5 V tolerant WR_N 17 I write strobe input input pad; TTL; 5 V tolerant A0 18 I bit 0 of the address bus input pad; TTL; 5 V tolerant A1 19 I bit 1 of the address bus A2 20 I bit 2 of the address bus input pad; TTL; 5 V tolerant input pad; TTL; 5 V tolerant VCC(I/O) A3 [3] 21 - supply voltage; used to supply voltage to the I/O pads; see Section 7.15 22 I bit 3 of the address bus input pad; TTL; 5 V tolerant ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 5 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Table 2. Pin description …continued Symbol[1] Pin Type[2] Description A4 23 I bit 4 of the address bus input pad; TTL; 5 V tolerant A5 24 I bit 5 of the address bus input pad; TTL; 5 V tolerant A6 25 I bit 6 of the address bus input pad; TTL; 5 V tolerant DGND 26 - digital ground A7 27 I bit 7 of the address bus input pad; TTL; 5 V tolerant VCC1V8[3] 28 - regulator output voltage (1.8 V ± 0.15 V); tapped out voltage from the internal regulator; this regulated voltage cannot drive external devices; decouple this pin using a 0.1 µF capacitor; see Section 7.15 DGND 29 - digital ground DATA0 30 I/O bit 0 of bidirectional data bus bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant DATA1 31 I/O bit 1 of bidirectional data bus DATA2 32 I/O bit 2 of bidirectional data bus bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant DATA3 33 I/O bit 3 of bidirectional data bus bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant VCC(I/O) [3] DATA4 34 - supply voltage; used to supply voltage to the I/O pads; see Section 7.15 35 I/O bit 4 of bidirectional data bus bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant DATA5 36 I/O bit 5 of bidirectional data bus bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant DATA6 37 I/O bit 6 of bidirectional data bus bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant DATA7 38 I/O bit 7 of bidirectional data bus DATA8 39 I/O bit 8 of bidirectional data bus bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant DATA9 40 I/O bit 9 of bidirectional data bus bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant DGND 41 - digital ground DATA10 42 I/O bit 10 of bidirectional data bus bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant DATA11 43 I/O bit 11 of bidirectional data bus bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant DATA12 44 I/O bit 12 of bidirectional data bus bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 6 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Table 2. Pin description …continued Symbol[1] Pin Type[2] Description DATA13 45 I/O bit 13 of bidirectional data bus bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant DATA14 46 I/O bit 14 of bidirectional data bus bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant DATA15 47 I/O bit 15 of bidirectional data bus bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant VCC(I/O) [3] VBUS 48 - supply voltage; used to supply voltage to the I/O pads; see Section 7.15 49 A USB bus power sensing input — Used to detect whether the host is connected or not; connect a 1 µF electrolytic or tantalum capacitor, and a 1 MΩ pull-down resistor to ground; see Section 7.13 VBUS pulsing output — In OTG mode; connect a 1 µF electrolytic or tantalum capacitor, and a 1 MΩ pull-down resistor to ground; see Section 7.13 5 V tolerant VCC1V8[3] 50 - voltage regulator output (1.8 V ± 0.15 V); tapped out voltage from the internal regulator; this regulated voltage cannot drive external devices; decouple this pin using 4.7 µF and 0.1 µF capacitors; see Section 7.15 XTAL2 51 O crystal oscillator output (12 MHz); connect a fundamental parallel-resonant crystal; leave this pin open when using an external clock source on pin XTAL1; see Table 79 XTAL1 52 I crystal oscillator input (12 MHz); connect a fundamental parallel-resonant crystal or an external clock source (leaving pin XTAL2 unconnected); see Table 79 VCC[3] 53 - supply voltage (3.3 V ± 0.3 V); this pin supplies the internal voltage regulator and the analog circuit; see Section 7.15 VCC[3] 54 - supply voltage (3.3 V ± 0.3 V); this pin supplies the internal voltage regulator and the analog circuit; see Section 7.15 WAKEUP 55 I wake-up input; when this pin is at the HIGH level, the chip is prevented from getting into the suspend state and wake-up the chip when already in suspend mode; when not in use, connect this pin to ground through a 10 kΩ resistor When the RESET_N pin is LOW, ensure that the WAKEUP pin does not go from LOW to HIGH; otherwise the device will enter test mode. input pad; TTL; 5 V tolerant SUSPEND 56 O suspend state indicator output; used as a power switch control output to power-off or power-on external devices when going into suspend mode or recovering from suspend mode CMOS output; 8 mA drive GND exposed die pad - ground supply; down bonded to the exposed die pad (heat sink); to be connected to DGND during PCB layout [1] Symbol names ending with underscore N (for example, NAME_N) represent active LOW signals. [2] All outputs and I/O pins can source 4 mA, unless otherwise specified. [3] Add a decoupling capacitor (0.1 µF) to all the supply pins. For better EMI results, add a 0.01 µF capacitor in parallel to the 0.1 µF. ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 7 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller 7. Functional description The ISP1582 is a high-speed USB peripheral controller. It implements the Hi-Speed USB or the Original USB physical layer, and the packet protocol layer. It concurrently maintains up to 16 USB endpoints (control IN, control OUT, and seven IN and seven OUT configurable) along with endpoint EP0 setup, which accesses the set-up buffer. The Ref. 1 “Universal Serial Bus Specification Rev. 2.0”, Chapter 9 protocol handling is executed using the external firmware. For high-bandwidth data transfer, the integrated DMA handler can be invoked to transfer data to or from external memory or devices. The DMA interface can be configured by writing to proper DMA registers (see Section 8.4). The ISP1582 supports Hi-Speed USB and Original USB signaling. The USB signaling speed is automatically detected. The ISP1582 has 8 kB of internal FIFO memory, which is shared among enabled USB endpoints, including control IN and control OUT endpoints, and set-up token buffer. There are seven IN and seven OUT configurable endpoints, and two fixed control endpoints that are 64 bytes long. Any of the seven IN and seven OUT endpoints can be separately enabled or disabled. The endpoint type (interrupt, isochronous or bulk) and packet size of these endpoints can be individually configured, depending on the requirements of the application. Optional double buffering increases the data throughput of these data endpoints. The ISP1582 requires 3.3 V power supply. It has 5 V tolerant I/O pads and an internal 1.8 V regulator to power the digital logic. Table 3. Endpoint access and programmability Endpoint identifier Maximum packet size Double buffering Endpoint type EP0SETUP 8 bytes (fixed) no set-up token OUT EP0RX 64 bytes (fixed) no control OUT OUT EP0TX 64 bytes (fixed) no control IN IN EP1RX programmable yes programmable OUT EP1TX programmable yes programmable IN EP2RX programmable yes programmable OUT EP2TX programmable yes programmable IN EP3RX programmable yes programmable OUT EP3TX programmable yes programmable IN EP4RX programmable yes programmable OUT EP4TX programmable yes programmable IN EP5RX programmable yes programmable OUT EP5TX programmable yes programmable IN EP6RX programmable yes programmable OUT EP6TX programmable yes programmable IN EP7RX programmable yes programmable OUT EP7TX programmable yes programmable IN ISP1582_7 Product data sheet Direction © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 8 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller The ISP1582 operates on a 12 MHz crystal oscillator. An integrated 40 × PLL clock multiplier generates the internal sampling clock of 480 MHz. 7.1 DMA interface, DMA handler and DMA registers The DMA block can be subdivided into two blocks: DMA handler and DMA interface. The firmware writes to the DMA Command register to start a DMA transfer (see Table 44). The handler interfaces to the same FIFO (internal RAM) as used by the USB core. On receiving the DMA command, the DMA handler directs the data from the endpoint FIFO to the external DMA device or from the external DMA device to the endpoint FIFO. The DMA interface configures the timing and the DMA handshake. Data can be transferred using either the DIOR and DIOW strobes or by the DACK and DREQ handshakes. DMA configurations are set up by writing to the DMA Configuration register (see Table 49 and Table 50). Remark: The DMA endpoint buffer length must be a multiple of 4 bytes. For details on DMA registers, see Section 8.4. 7.2 Hi-Speed USB transceiver The analog transceiver directly interfaces to the USB cable through integrated termination resistors. The high-speed transceiver requires an external resistor (12.0 kΩ ± 1 %) between pin RREF and ground to ensure an accurate current mirror that generates the Hi-Speed USB current drive. A full-speed transceiver is integrated as well. This makes the ISP1582 compliant to Hi-Speed USB and Original USB, supporting both the high-speed and full-speed physical layers. After automatic speed detection, the NXP Serial Interface Engine (SIE) sets the transceiver to use either high-speed or full-speed signaling. 7.3 MMU and integrated RAM The Memory Management Unit (MMU) manages the access to the integrated RAM that is shared by the USB, microcontroller handler and DMA handler. Data from the USB bus is stored in the integrated RAM, which is cleared only when the microcontroller has read the corresponding endpoint, or the DMA controller has written all data from the RAM of the corresponding endpoint to the DMA bus. The OUT endpoint buffer can also be forcibly cleared by setting bit CLBUF in the Control Function register. A total of 8 kB RAM is available for buffering. 7.4 Microcontroller interface and microcontroller handler The microcontroller handler allows the external microcontroller or microprocessor to access the register set in the NXP SIE, as well as the DMA handler. The initialization of the DMA configuration is done through the microcontroller handler. 7.5 OTG SRP module The OTG supplement defines a Session Request Protocol (SRP), which allows a B-device to request the A-device to turn on VBUS and start a session. This protocol allows the A-device, which may be battery-powered, to conserve power by turning off VBUS when there is no bus activity while still providing a means for the B-device to initiate bus activity. ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 9 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Any A-device, including a PC or laptop, can respond to SRP. Any B-device, including a standard USB peripheral, can initiate SRP. The ISP1582 is a device that can initiate SRP. 7.6 NXP high-speed transceiver 7.6.1 NXP Parallel Interface Engine (PIE) In the High-Speed (HS) transceiver, the NXP PIE interface uses a 16-bit parallel bidirectional data interface. The functions of the HS module also include bit-stuffing or de-stuffing and Non-Return-to-Zero Inverted (NRZI) encoding or decoding logic. 7.6.2 Peripheral circuit To maintain a constant current driver for HS transmit circuits and to bias other analog circuits, an internal band gap reference circuit and an RREF resistor form the reference current. This circuit requires an external precision resistor (12.0 kΩ ± 1 %) connected to the analog ground. 7.6.3 HS detection The ISP1582 handles more than one electrical state, Full-Speed (FS) or High-Speed (HS), under the USB specification. When the USB cable is connected from the peripheral to the host controller, the ISP1582 defaults to the FS state, until it sees a bus reset from the host controller. During the bus reset, the peripheral initiates an HS chirp to detect whether the host controller supports Hi-Speed USB or Original USB. If the HS handshake shows that there is an HS host connected, then the ISP1582 switches to the HS state. In the HS state, the ISP1582 must observe the bus for periodic activity. If the bus remains inactive for 3 ms, the peripheral switches to the FS state to check for a Single-Ended Zero (SE0) condition on the USB bus. If an SE0 condition is detected for the designated time (100 µs to 875 µs; refer to Ref. 1 “Universal Serial Bus Specification Rev. 2.0”, Section 7.1.7.6), the ISP1582 switches to the HS chirp state to perform an HS detection handshake. Otherwise, the ISP1582 remains in the FS state, adhering to the bus-suspend specification. 7.6.4 Isolation Ensure that the DP and DM lines are maintained in a clean state, without any residual voltage or glitches. Once the ISP1582 is reset and the clock is available, ensure that there are no erroneous pulses or glitches even of very small amplitude on the DP and DM lines. Remark: If there are any erroneous unwanted pulses or glitches detected by the ISP1582 DP and DM lines, there is a possibility of the ISP1582 clocking this state into the internal core, causing unknown behaviors. ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 10 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller 7.7 NXP Serial Interface Engine (SIE) The NXP SIE implements the full USB protocol layer. It is completely hardwired for speed and needs no firmware intervention. The functions of this block include: synchronization pattern recognition, parallel or serial conversion, bit-stuffing or de-stuffing, CRC checking or generation, Packet IDentifier (PID) verification or generation, address recognition, handshake evaluation or generation. 7.8 SoftConnect The USB connection is established by pulling pin DP (for full-speed devices) to HIGH through a 1.5 kΩ pull-up resistor. In the ISP1582, an external 1.5 kΩ pull-up resistor must be connected between pin RPU and 3.3 V. Pin RPU connects the pull-up resistor to pin DP, when bit SOFTCT in the Mode register is set (see Table 18 and Table 19). After a hardware reset, the pull-up resistor is disconnected by default (bit SOFTCT = 0). The USB bus reset does not change the value of bit SOFTCT. When VBUS is not present, the SOFTCT bit must be set to logic 0 to comply with the back-drive voltage. 7.9 Reconfiguring endpoints The ISP1582 endpoints have a limitation when implementing a composite device with at least two functionalities that require the support of alternate settings, for example, the video class and audio class devices. The ISP1582 endpoints cannot be reconfigured on the fly because it is implemented as a FIFO base. The internal RAM partition will be corrupted if there is a need to reconfigure endpoints on the fly because of alternate settings request, causing data corruption. For details and workaround, refer to Ref. 3 “Using ISP1582/3 in a composite device application with alternate settings (AN10071)”. 7.10 System controller The system controller implements the USB power-down capabilities of the ISP1582. Registers are protected against data corruption during wake-up following a resume (from the suspend state) by locking the write access, until an unlock code is written in the Unlock Device register (see Table 69 and Table 70). 7.11 Pins status Table 4 illustrates the behavior of ISP1582 pins with VCC(I/O) and VCC in various operating conditions. Table 4. VCC ISP1582 pin status VCC(I/O) State Pin Input Output I/O dead[1] unknown unknown unknown 3.3 V VCC reset state depends on how the pin is driven output 3.3 V VCC after reset state depends on how the pin is driven output 0V [1] 0V high-Z state depends on how the pin is configured Dead: The USB cable is plugged out, and VCC(I/O) is not available. ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 11 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Table 5 illustrates the behavior of output pins with VCC(I/O) and VCC in various operating conditions. Table 5. ISP1582 output status VCC VCC(I/O) State INT SUSPEND 0V dead[1] X[2] X[2] 3.3 V VCC reset HIGH LOW 3.3 V VCC after reset HIGH LOW 0V [1] Dead: The USB cable is plugged out, and VCC(I/O) is not available. [2] X: Don’t care. 7.12 Interrupt 7.12.1 Interrupt output pin The Interrupt Configuration register of the ISP1582 controls the behavior of the INT output pin. The polarity and signaling mode of pin INT can be programmed by setting bits INTPOL and INTLVL of the Interrupt Configuration register (R/W: 10h); see Table 22. Bit GLINTENA of the Mode register (R/W: 0Ch) is used to enable pin INT. Default settings after reset are active LOW and level mode. When pulse mode is selected, a pulse of 60 ns is generated when the OR-ed combination of all interrupt bits changes from logic 0 to logic 1. Figure 3 shows the relationship between interrupt events and pin INT. Each of the indicated USB and DMA events is logged in a status bit of the Interrupt register and the DMA Interrupt Reason register, respectively. Corresponding bits in the Interrupt Enable register and the DMA Interrupt Enable register determine whether an event will generate an interrupt. Interrupts can be masked globally by means of bit GLINTENA of the Mode register; see Table 19. Field CDBGMOD[1:0] of the Interrupt Configuration register controls the generation of INT signals for the control pipe. Field DDBGMODIN[1:0] of the Interrupt Configuration register controls the generation of INT signals for the IN pipe. Field DDBGMODOUT[1:0] of the Interrupt Configuration register controls the generation of INT signals for the OUT pipe; see Table 23. ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 12 of 68 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx NXP Semiconductors ISP1582_7 Product data sheet Interrupt Enable register DMA Interrupt Reason register IEBRESET IESOF EXT_EOT .... INT_EOT DMA_XFER_OK IEDMA ...... DMA Interrupt Enable register IE_EXT_EOT .... Rev. 07 — 22 September 2008 OR IE_INT_EOT IE_DMA_XFER_OK IEP7RX IEP7TX OR Interrupt register BRESET SOF ...... .... LE Interrupt Configuration register INT ...... PULSE OR LEVEL GENERATOR INTPOL Mode register EP7RX GLINTENA 004aaa275 Fig 3. Interrupt logic ISP1582 13 of 68 © NXP B.V. 2008. All rights reserved. EP7TX Hi-Speed USB peripheral controller LATCH DMA ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller 7.12.2 Interrupt control Bit GLINTENA in the Mode register is a global interrupt enable or disable bit. The behavior of this bit is given in Figure 4. The following illustrations are only applicable for level trigger. Event A: When an interrupt event occurs (for example, SOF interrupt) with bit GLINTENA set to logic 0, an interrupt will not be generated at pin INT. It will, however, be registered in the corresponding Interrupt register bit. Event B: When bit GLINTENA is set to logic 1, pin INT is asserted because bit SOF in the Interrupt register is already set. Event C: If the firmware sets bit GLINTENA to logic 0, pin INT will still be asserted. The bold line shows the desired behavior of pin INT. Deassertion of pin INT can be achieved either by clearing all the bits in the Interrupt register or the DMA Interrupt Reason register, depending on the event. Remark: When clearing an interrupt event, perform write to all the bytes of the register. For more information on interrupt control, see Section 8.2.2, Section 8.2.5 and Section 8.5.1. A B C INT pin GLINTENA = 0 (during this time, an interrupt event occurs, for example, SOF asserted) GLINTENA = 1 SOF asserted GLINTENA = 0 SOF asserted 004aaa394 Pin INT: HIGH = deassert; LOW = assert (individual interrupts are enabled). Fig 4. Behavior of bit GLINTENA 7.13 VBUS sensing The VBUS pin is one of the ways to wake up the clock when the ISP1582 is suspended with bit CLKAON set to logic 0 (clock off option). To detect whether the host is connected or not, that is VBUS sensing, a 1 MΩ resistor and a 1 µF electrolytic or tantalum capacitor must be added to damp the overshoot on plug-in. ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 14 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller 49 ISP1582 1 MΩ 1 µF USB CONNECTOR 004aaa440 Fig 5. Resistor and electrolytic or tantalum capacitor needed for VBUS sensing 001aaf440 Fig 6. Oscilloscope reading: no resistor and capacitor in the network 001aaf441 Fig 7. Oscilloscope reading: with resistor and capacitor in the network 7.14 Power-on reset The ISP1582 requires a minimum pulse width of 500 µs. ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 15 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller The RESET_N pin can either be connected to VCC (using the internal POR circuit) or externally controlled (by the microcontroller, ASIC, and so on). When VCC is directly connected to the RESET_N pin, the internal pulse width tPORP will typically be 200 ns. The power-on reset function can be explained by viewing the dips at t2 to t3 and t4 to t5 on the VCC(POR) curve (Figure 8). t0 — The internal POR starts with a HIGH level. t1 — The detector will see the passing of the trip level and a delay element will add another tPORP before it drops to LOW. t2-t3 — The internal POR pulse will be generated whenever VCC(POR) drops below Vtrip for more than 11 µs. t4-t5 — The dip is too short (< 11 µs) and the internal POR pulse will not react and will remain LOW. VCC(POR) Vtrip t0 t1 t4 t3 t2 t5 PORP(1) tPORP tPORP 004aab162 (1) PORP = Power-On Reset Pulse. Fig 8. POR timing Figure 9 shows the availability of the clock with respect to the external POR. VCC 500 µs external clock 2 ms RESET_N A B C 004aaa927 Power on VCC at A. Stable external clock is to be available at B. The ISP1582 is operational at C. Fig 9. Clock with respect to the external POR 7.15 Power supply The ISP1582 can be powered by 3.3 V ± 0.3 V. For connection details, see Figure 10. If the ISP1582 is powered by VCC = 3.3 V, an integrated 3.3 V-to-1.8 V voltage regulator provides a 1.8 V supply voltage for the internal logic. ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 16 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller 53, 54 3.3 V ± 0.3 V VCC 0.1 µF 0.01 µF 48 VCC(I/O) VCC 0.01 µF 34 0.1 µF VCC(I/O) 0.01 µF 0.1 µF ISP1582 21 VCC(I/O) 0.1 µF 0.01 µF 50 VCC1V8 4.7 µF(1) 28 0.1 µF VCC1V8 0.1 µF 004aaa203 (1) At the VCC input (3.3 V) to the USB controller, if the ripple voltage is less than 20 mV, then 4.7 µF standard electrolytic or tantalum capacitors (tested ESR up to 10 Ω) should be OK at the VCC1V8 output. If the ripple voltage at the input is higher than 20 mV, then use 4.7 µF LOW ESR capacitors (ESR from 0.2 Ω to 2 Ω) at the VCC1V8 output. This is to improve the high-speed signal quality at the USB side. Fig 10. ISP1582 with 3.3 V supply Table 6 shows power modes in which the ISP1582 can be operated. Table 6. Power modes VCC VBUS [1] System-powered VCC(I/O) Power mode [2] bus-powered VBUS system-powered [1] The power supply to the IC (VCC) is 3.3 V. Therefore, if the application is bus-powered, a 3.3 V regulator must be used. [2] VCC(I/O) = VCC. If the application is bus-powered, a voltage regulator must be used. ISP1582_7 Product data sheet self-powered © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 17 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller 7.15.1 Self-powered mode 1.5 kΩ RPU VCC VBUS VBUS ISP1582 1 µF USB 1 MΩ VCC(I/O) 004aaa460 VCC(I/O) and VCC are system powered. Fig 11. Self-powered mode In self-powered mode, VCC and VCC(I/O) are supplied by the system. See Figure 11. Table 7. Operation truth table for SoftConnect ISP1582 operation Power supply Normal bus operation No pull-up on DP [1] VCC VCC(I/O) RPU (3.3 V) VBUS 3.3 V 3.3 V 3.3 V 5V 3.3 V 3.3 V 3.3 V 0 V[1] Bit SOFTCT in Mode register enabled disabled When the USB cable is removed, SoftConnect is disabled. Table 8. Operation truth table for clock off during suspend ISP1582 operation Power supply Clock will wake up: Clock off during suspend VCC VCC(I/O) RPU (3.3 V) VBUS 3.3 V 3.3 V 3.3 V 5V enabled 3.3 V 3.3 V 3.3 V 0V→5V enabled After resume and After a bus reset Clock will wake up: After detecting the presence of VBUS Table 9. Operation truth table for back voltage compliance ISP1582 operation Power supply VCC(I/O) RPU (3.3 V) VBUS 3.3 V 3.3 V 3.3 V 5V enabled Back voltage is not an issue because pull 3.3 V up on DP will not be present when VBUS is not present 3.3 V 3.3 V 0V disabled Back voltage is not measured in this mode ISP1582_7 Product data sheet Bit SOFTCT in Mode register VCC © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 18 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Table 10. Operation truth table for OTG ISP1582 operation Power supply OTG register VCC VCC(I/O) RPU (3.3 V) VBUS SRP is not applicable 3.3 V 3.3 V 3.3 V 5V not applicable SRP is possible 3.3 V 3.3 V 3.3 V 0V operational 7.15.2 Bus-powered mode 5 V-to-3.3 V VOLTAGE REGULATOR VBUS VBUS VCC 3.3 V USB ISP1582 1 µF 1 MΩ VCC(I/O) 1.5 kΩ RPU 004aaa462 VCC(I/O) is powered by VBUS. Fig 12. Bus-powered mode In bus-powered mode (see Figure 12), VCC and VCC(I/O) are supplied by the output of the 5 V-to-3.3 V voltage regulator. The input to the regulator is from VBUS. On plugging the USB cable, the ISP1582 goes through the power-on reset cycle. In this mode, OTG is disabled. Table 11. Operation truth table for SoftConnect ISP1582 operation Power supply Bit SOFTCT in Mode register VCC VCC(I/O) RPU (3.3 V) VBUS Normal bus operation 3.3 V 3.3 V 3.3 V 5V enabled Power loss 0V 0V 0V 0V not applicable Table 12. Operation truth table for clock off during suspend ISP1582 operation Clock will wake up: Power supply Clock off during suspend VCC VCC(I/O) RPU (3.3 V) VBUS 3.3 V 3.3 V 3.3 V 5V enabled 0V 0V 0V 0V not applicable After resume and After a bus reset Power loss ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 19 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Table 13. Operation truth table for back voltage compliance ISP1582 operation Power supply VCC VCC(I/O) RPU (3.3 V) VBUS Back voltage is not measured in this mode 3.3 V 3.3 V 3.3 V 5V enabled Power loss 0V 0V 0V 0V not applicable Table 14. Operation truth table for OTG ISP1582 operation Power supply VCC VCC(I/O) OTG register RPU (3.3 V) VBUS SRP is not applicable 3.3 V 3.3 V 3.3 V 5V not applicable Power loss 0V 0V 0V 0V not applicable ISP1582_7 Product data sheet Bit SOFTCT in Mode register © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 20 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller 8. Register description Table 15. Register overview Name Destination Address Description Size (bytes) Reference Address device 00h USB device address and enable 1 Section 8.2.1 on page 22 Mode device 0Ch power-down options, global interrupt enable, SoftConnect 2 Section 8.2.2 on page 23 Interrupt Configuration device 10h interrupt sources, trigger mode, output polarity 1 Section 8.2.3 on page 24 OTG device 12h OTG implementation 1 Section 8.2.4 on page 25 Interrupt Enable device 14h interrupt source enabling 4 Section 8.2.5 on page 27 Endpoint Index endpoints 2Ch endpoint selection, data flow direction 1 Section 8.3.1 on page 29 Control Function endpoint 28h endpoint buffer management 1 Section 8.3.2 on page 30 Data Port endpoint 20h data access to endpoint FIFO 2 Section 8.3.3 on page 31 Buffer Length endpoint 1Ch packet size counter 2 Section 8.3.4 on page 32 Buffer Status endpoint 1Eh buffer status for each endpoint 1 Section 8.3.5 on page 33 Endpoint MaxPacketSize endpoint 04h maximum packet size 2 Section 8.3.6 on page 34 Endpoint Type endpoint 08h selects endpoint type: isochronous, bulk or interrupt 2 Section 8.3.7 on page 35 DMA Command DMA controller 30h controls all DMA transfers 1 Section 8.4.1 on page 37 DMA Transfer Counter DMA controller 34h sets byte count for DMA transfer 4 Section 8.4.2 on page 38 DMA Configuration DMA controller 38h sets GDMA configuration (counter enable, data strobing, bus width) 2 Section 8.4.3 on page 39 DMA Hardware DMA controller 3Ch endian type, signal polarity for DACK, DREQ, DIOW, DIOR, EOT 1 Section 8.4.4 on page 40 DMA Interrupt Reason DMA controller 50h shows reason (source) for DMA interrupt 2 Section 8.4.5 on page 41 DMA Interrupt Enable DMA controller 54h enables DMA interrupt sources 2 Section 8.4.6 on page 42 DMA Endpoint DMA controller 58h selects endpoint FIFO, data flow direction 1 Section 8.4.7 on page 43 DMA Burst Counter DMA controller 64h DMA burst counter Section 8.4.8 on page 43 Initialization registers Data flow registers DMA registers ISP1582_7 Product data sheet 2 © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 21 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Table 15. Register overview …continued Name Destination Address Description Size (bytes) Reference Interrupt device 18h shows interrupt sources 4 Section 8.5.1 on page 44 Chip ID device 70h product ID code and hardware version 3 Section 8.5.2 on page 46 Frame Number device 74h last successfully received Start-Of-Frame: lower byte (byte 0) is accessed first 2 Section 8.5.3 on page 46 Scratch device 78h allows save or restore of firmware status during suspend 2 Section 8.5.4 on page 47 Unlock Device device 7Ch re-enables register write access after suspend 2 Section 8.5.5 on page 47 Test Mode PHY 84h direct setting of the DP and DM states, internal transceiver test (PHY) 1 Section 8.5.6 on page 48 General registers 8.1 Register access The ISP1582 uses a 16-bit bus access. For single-byte registers, the upper byte (MSByte) must be ignored. Endpoint specific registers are indexed using the Endpoint Index register. The target endpoint must be selected before accessing the following registers: • • • • • • Buffer length Buffer status Control function Data port Endpoint MaxPacketSize Endpoint type Remark: Write zero to all reserved bits, unless otherwise specified. 8.2 Initialization registers 8.2.1 Address register (address: 00h) This register sets the USB assigned address and enables the USB device. Table 16 shows the Address register bit allocation. Bits DEVADDR[6:0] will be cleared whenever a bus reset, a power-on reset or a soft reset occurs. Bit DEVEN will be cleared whenever a power-on reset or a soft reset occurs. In response to the standard USB request SET_ADDRESS, firmware must write the (enabled) device address to the Address register, followed by sending an empty packet to the host. The new device address is activated when the device receives an acknowledgment from the host for the empty packet token. ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 22 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Table 16. Address register: bit allocation Bit 7 Symbol 5 4 DEVEN Reset Bus reset 6 3 2 1 0 DEVADDR[6:0] 0 0 0 0 0 0 0 0 unchanged 0 0 0 0 0 0 0 R/W R/W R/W R/W R/W R/W R/W R/W Access Table 17. Address register: bit description Bit Symbol Description 7 DEVEN Device Enable: Logic 1 enables the device. The device will not respond to the host, unless this bit is set. 6 to 0 DEVADDR [6:0] Device Address: This field specifies the USB device address. 8.2.2 Mode register (address: 0Ch) This register consists of 2 bytes (bit allocation: see Table 18). The Mode register controls resume, suspend and wake-up behavior, interrupt activity, soft reset, clock signals and SoftConnect operation. Table 18. Mode register: bit allocation Bit 15 14 13 Symbol 12 11 10 reserved 9 8 DMA CLKON VBUSSTAT Reset - - - - - - 0 -[1] Bus reset - - - - - - 0 -[1] Access R R R R R R R/W R Bit 7 6 5 4 3 2 1 0 CLKAON SNDRSU GOSUSP SFRESET GLINTENA WKUPCS PWRON SOFTCT 0 0 0 0 0 0 0 0 Symbol Reset Bus reset unchanged 0 0 0 unchanged 0 unchanged unchanged R/W R/W R/W R/W R/W R/W R/W R/W Access [1] Value depends on the status of the VBUS pin. Table 19. Mode register: bit description Bit Symbol Description 15 to 10 - reserved 9 DMACLKON DMA Clock On: 0 — Power save mode; the DMA circuit will stop completely to save power. 1 — Supply clock to the DMA circuit. 8 VBUSSTAT VBUS Pin Status: This bit reflects the VBUS pin status. ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 23 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Table 19. Mode register: bit description …continued Bit Symbol Description 7 CLKAON Clock Always On: Logic 1 indicates that internal clocks are always running when in the suspend state. Logic 0 switches off the internal oscillator and PLL when the device goes into suspend mode. The device will consume less power if this bit is set to logic 0. The clock is stopped about 2 ms after bit GOSUSP is set and then cleared. 6 SNDRSU Send Resume: Writing logic 1, followed by logic 0 will generate a 10 ms upstream resume signal. Remark: The upstream resume signal is generated 5 ms after this bit is set to logic 0. 5 GOSUSP Go Suspend: Writing logic 1, followed by logic 0 will activate suspend mode. 4 SFRESET Soft Reset: Writing logic 1, followed by logic 0 will enable a software-initiated reset to the ISP1582. A soft reset is similar to a hardware-initiated reset (using pin RESET_N). 3 GLINTENA Global Interrupt Enable: Logic 1 enables all interrupts. Individual interrupts can be masked by clearing the corresponding bits in the Interrupt Enable register. When this bit is not set, an unmasked interrupt will not generate an interrupt trigger on the interrupt pin. If global interrupt, however, is enabled while there is any pending unmasked interrupt, an interrupt signal will be immediately generated on the interrupt pin. (If the interrupt is set to pulse mode, the interrupt events that were generated before the global interrupt is enabled will not appear on the interrupt pin). 2 WKUPCS Wake Up On Chip Select: Logic 1 enables wake-up from suspend mode through a valid register read on the ISP1582. (A read will invoke the chip clock to restart. If you write to the register before the clock gets stable, it may cause malfunctioning). 1 PWRON Power On: The SUSPEND pin output control. 0 — The SUSPEND pin is HIGH when the ISP1582 is in the suspend state. Otherwise, the SUSPEND pin is LOW. 1 — When the device is woken up from the suspend state, there will be a 1 ms active HIGH pulse on the SUSPEND pin. The SUSPEND pin will remain LOW in all other states. 0 SOFTCT SoftConnect: Logic 1 enables the connection of the 1.5 kΩ pull-up resistor on pin RPU to the DP pin. The status of the chip is shown in Table 20. Table 20. Status of the chip VBUS SoftConnect = on SoftConnect = off On pull-up resistor on pin DP pull-up resistor on pin DP is removed; suspend interrupt is generated after 3 ms of no bus activity Off pull-up resistor on pin DP is present; suspend interrupt is generated after 3 ms of no bus activity pull-up resistor on pin DP is removed; suspend interrupt is generated after 3 ms of no bus activity 8.2.3 Interrupt Configuration register (address: 10h) This 1-byte register determines the behavior and polarity of the INT output. The bit allocation is shown in Table 21. When the USB SIE receives or generates an ACK, NAK or NYET, it will generate interrupts, depending on three Debug mode fields. ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 24 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller CDBGMOD[1:0] — Interrupts for control endpoint 0 DDBGMODIN[1:0] — Interrupts for DATA IN endpoints 1 to 7 DDBGMODOUT[1:0] — Interrupts for DATA OUT endpoints 1 to 7 The Debug mode settings for CDBGMOD, DDBGMODIN and DDBGMODOUT allow you to individually configure when the ISP1582 sends an interrupt to the external microprocessor. Table 23 lists the available combinations. Bit INTPOL controls the signal polarity of the INT output: active HIGH or LOW, rising or falling edge. For level-triggering, bit INTLVL must be made logic 0. By setting INTLVL to logic 1, an interrupt will generate a pulse of 60 ns (edge-triggering). Table 21. Interrupt Configuration register: bit allocation Bit 7 Symbol CDBGMOD[1:0] Reset 1 1 1 1 1 Bus reset 1 1 1 1 R/W R/W R/W R/W Access 6 Table 22. 5 4 3 DDBGMODIN[1:0] 2 1 0 INTLVL INTPOL 1 0 0 1 1 unchanged unchanged R/W R/W R/W R/W DDBGMODOUT[1:0] Interrupt Configuration register: bit description Bit Symbol Description 7 to 6 CDBGMOD[1:0] Control Endpoint 0 Debug Mode: For values, see Table 23 Data Debug Mode IN: For values, see Table 23 5 to 4 DDBGMODIN[1:0] 3 to 2 DDBGMODOUT[1:0] Data Debug Mode OUT: For values, see Table 23 1 INTLVL Interrupt Level: Selects signaling mode on output INT (0 = level; 1 = pulsed). In pulsed mode, an interrupt produces a 60 ns pulse. 0 INTPOL Interrupt Polarity: Selects signal polarity on output INT (0 = active LOW; 1 = active HIGH). Table 23. Debug mode settings Value CDBGMOD DDBGMODIN DDBGMODOUT 00h interrupt on all ACK and NAK interrupt on all ACK and NAK interrupt on all ACK, NYET and NAK 01h interrupt on all ACK interrupt on ACK interrupt on ACK and NYET 1Xh interrupt on all ACK and first NAK[1] interrupt on all ACK and first NAK[1] interrupt on all ACK, NYET and first NAK[1] [1] First NAK: the first NAK on an IN or OUT token is generated after a set-up token and an ACK sequence. 8.2.4 OTG register (address: 12h) The bit allocation of the OTG register is given in Table 24. Table 24. OTG register: bit allocation Bit 7 Symbol 6 reserved 5 4 3 2 1 0 DP BSESSVALID INITCOND DISCV VP OTG Reset - - 0 - - 0 0 0 Bus reset - - 0 - - 0 0 0 Access - - R/W R/W R/W R/W R/W R/W ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 25 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Table 25. OTG register: bit description Bit Symbo Description[1][2][3] l 7 to 6 - reserved 5 DP Data Pulsing: Used for data-line pulsing to toggle DP to generate the required data-line pulsing signal. The default value of this bit is logic 0. This bit must be cleared when data-line pulsing is completed. 4 BSESS B-Session Valid: The device can initiate another VBUS discharge sequence after VALID data-line pulsing and VBUS pulsing, and before it clears this bit and detects a session valid. This bit is latched to logic 1 once VBUS exceeds the B-device session valid threshold. Once set, it remains at logic 1. To clear this bit, write logic 1. (The ISP1582 continuously updates this bit to logic 1 when the B-session is valid. If the B-session is valid after it is cleared, it is set back to logic 1 by the ISP1582). 0 — It implies that SRP has failed. To proceed to a normal operation, the device can restart SRP, clear bit OTG or proceed to an error handling process. 1 — It implies that the B-session is valid. The device clears bit OTG, goes into normal operation mode, and sets bit SOFTCT (DP pull-up) in the Mode register. The OTG host has a maximum of 5 s before it responds to a session request. During this period, the ISP1582 may request to suspend. Therefore, the device firmware must wait for some time if it wishes to know the SRP result (success: if there is minimum response from the host within 5 s; failure; if there is no response from the host within 5 s). 3 INIT COND Initial Condition: Write logic 1 to clear this bit. Wait for more than 2 ms and check the bit status. If it reads logic 0, it means that VBUS remains lower than 0.8 V, and DP or DM are at SE0 during the elapsed time. The device can then start a B-device SRP. If it reads logic 1, it means that the initial condition of SRP is violated. So, the device must abort SRP. The bit is set to logic 1 by the ISP1582 when initial conditions are not met, and only writing logic 1 clears the bit. (If initial conditions are not met after this bit has been cleared, it will be set again). Remark: This implementation does not cover the case if an initial SRP condition is violated when this bit is read and data-line pulsing is started. 2 DISCV Discharge VBUS: Set to logic 1 to discharge VBUS. The device discharges VBUS before starting a new SRP. The discharge can take as long as 30 ms for VBUS to be charged less than 0.8 V. This bit must be cleared (write logic 0) before starting a session end detection. 1 VP VBUS Pulsing: Used for VBUS pulsing to toggle VP to generate the required VBUS pulsing signal. This bit must be set for more than 16 ms and must be cleared before 26 ms. 0 OTG On-The-Go: 1 — Enables the OTG function. The VBUS sensing functionality will be disabled. 0 — Normal operation. All OTG control bits will be masked. Status bits are undefined. [1] No interrupt is designed for OTG. The VBUS interrupt, however, may assert as a side effect during the VBUS pulsing (see note 2). [2] When OTG is in progress, the VBUS interrupt may be set because VBUS is charged over the VBUS sensing threshold or the OTG host has turned on the VBUS supply to the device. Even if the VBUS interrupt is found during SRP, the device must complete data-line pulsing and VBUS pulsing before starting the B_SESSION_VALID detection. [3] OTG implementation applies to the device with self-power capability. If the device works in sharing mode, it must provide a switch circuit to supply power to the ISP1582 core during SRP. ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 26 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller 8.2.4.1 Session Request Protocol (SRP) The ISP1582 can initiate an SRP. The B-device initiates SRP by data-line pulsing, followed by VBUS pulsing. The A-device can detect either data-line pulsing or VBUS pulsing. The ISP1582 can initiate the B-device SRP by performing the following steps: 1. Set the OTG bit to start SRP. 2. Detect initial conditions by following the instructions given in bit INITCOND of the OTG register. 3. Start data-line pulsing: set bit DP of the OTG register to logic 1. 4. Wait for 5 ms to 10 ms. 5. Stop data-line pulsing: set bit DP of the OTG register to logic 0. 6. Start VBUS pulsing: set bit VP of the OTG register to logic 1. 7. Wait for 10 ms to 20 ms. 8. Stop VBUS pulsing: set bit VP of the OTG register to logic 0. 9. Discharge VBUS for about 30 ms: optional by using bit DISCV of the OTG register. 10. Detect bit BSESSVALID of the OTG register for a successful SRP with bit OTG cleared. 11. Once bit BSESSVALID is detected, turn on the SOFTCT bit to start normal bus enumeration. The B-device must complete both data-line pulsing and VBUS pulsing within 100 ms. Remark: When disabling OTG, data-line pulsing bit DP and VBUS pulsing bit VP must be cleared by writing logic 0. 8.2.5 Interrupt Enable register (address: 14h) This register enables or disables individual interrupt sources. The interrupt for each endpoint can individually be controlled using the associated bits IEPnRX or IEPnTX, here n represents the endpoint number. All interrupts can be globally disabled using bit GLINTENA in the Mode register (see Table 18). An interrupt is generated when the USB SIE receives or generates an ACK or NAK on the USB bus. The interrupt generation depends on Debug mode settings of bit fields CDBGMOD[1:0], DDBGMODIN[1:0] and DDBGMODOUT[1:0] in the Interrupt Configuration register. All data IN transactions use the Transmit buffers (TX), which are handled by bits DDBGMODIN[1:0]. All data OUT transactions go through the Receive buffers (RX), which are handled by bits DDBGMODOUT[1:0]. Transactions on control endpoint 0 (IN, OUT and SETUP) are handled by bits CDBGMOD[1:0]. Interrupts caused by events on the USB bus (SOF, suspend, resume, bus reset, set up and high-speed status) can also be individually controlled. A bus reset disables all enabled interrupts, except bit IEBRST (bus reset), which remains logic 1. The Interrupt Enable register consists of 4 bytes. The bit allocation is given in Table 26. ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 27 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Table 26. Interrupt Enable register: bit allocation Bit 31 30 29 Symbol 28 27 26 reserved 25 24 IEP7TX IEP7RX Reset - - - - - - 0 0 Bus reset - - - - - - 0 0 Access - - - - - - R/W R/W 23 22 21 20 19 18 17 16 Bit Symbol IEP6TX IEP6RX IEP5TX IEP5RX IEP4TX IEP4RX IEP3TX IEP3RX Reset 0 0 0 0 0 0 0 0 Bus reset 0 0 0 0 0 0 0 0 R/W R/W R/W R/W R/W R/W R/W R/W Access Bit 15 14 13 12 11 10 9 8 IEP2TX IEP2RX IEP1TX IEP1RX IEP0TX IEP0RX reserved IEP0SETUP Reset 0 0 0 0 0 0 - 0 Bus reset 0 0 0 0 0 0 - 0 R/W R/W R/W R/W R/W R/W R/W R/W 7 6 5 4 3 2 1 0 IEVBUS IEDMA IEHS_STA IERESM IESUSP IEPSOF IESOF IEBRST 0 0 0 0 0 0 0 0 Symbol Access Bit Symbol Reset Bus reset Access 0 0 0 0 0 0 0 1 R/W R/W R/W R/W R/W R/W R/W R/W Table 27. Interrupt Enable register: bit description Bit Symbol Description 31 to 26 - reserved 25 IEP7TX Logic 1 enables interrupt from the indicated endpoint. 24 IEP7RX Logic 1 enables interrupt from the indicated endpoint. 23 IEP6TX Logic 1 enables interrupt from the indicated endpoint. 22 IEP6RX Logic 1 enables interrupt from the indicated endpoint. 21 IEP5TX Logic 1 enables interrupt from the indicated endpoint. 20 IEP5RX Logic 1 enables interrupt from the indicated endpoint. 19 IEP4TX Logic 1 enables interrupt from the indicated endpoint. 18 IEP4RX Logic 1 enables interrupt from the indicated endpoint. 17 IEP3TX Logic 1 enables interrupt from the indicated endpoint. 16 IEP3RX Logic 1 enables interrupt from the indicated endpoint. 15 IEP2TX Logic 1 enables interrupt from the indicated endpoint. 14 IEP2RX Logic 1 enables interrupt from the indicated endpoint. 13 IEP1TX Logic 1 enables interrupt from the indicated endpoint. 12 IEP1RX Logic 1 enables interrupt from the indicated endpoint. 11 IEP0TX Logic 1 enables interrupt from the control IN endpoint 0. 10 IEP0RX Logic 1 enables interrupt from the control OUT endpoint 0. 9 - reserved 8 IEP0SETUP Logic 1 enables interrupt for the set-up data received on endpoint 0. ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 28 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Table 27. Interrupt Enable register: bit description …continued Bit Symbol Description 7 IEVBUS Logic 1 enables interrupt for VBUS sensing. 6 IEDMA Logic 1 enables interrupt on the DMA Interrupt Reason register change detection. 5 IEHS_STA Logic 1 enables interrupt on detection of a high-speed status change. 4 IERESM Logic 1 enables interrupt on detection of a resume state. 3 IESUSP Logic 1 enables interrupt on detection of a suspend state. 2 IEPSOF Logic 1 enables interrupt on detection of a pseudo SOF. 1 IESOF Logic 1 enables interrupt on detection of an SOF. 0 IEBRST Logic 1 enables interrupt on detection of a bus reset. 8.3 Data flow registers 8.3.1 Endpoint Index register (address: 2Ch) The Endpoint Index register selects a target endpoint for register access by the microcontroller. The register consists of 1 byte, and the bit allocation is shown in Table 28. The following registers are indexed: • • • • • • Buffer length Buffer status Control function Data port Endpoint MaxPacketSize Endpoint type For example, to access the OUT data buffer of endpoint 1 using the Data Port register, the Endpoint Index register must be written first with 02h. Remark: The Endpoint Index register and the DMA Endpoint register must not point to the same endpoint, irrespective of IN and OUT. Remark: The delay time from the Write Endpoint Index register to the Read Data Port register must be at least 190 ns. Remark: The delay time from the Write Endpoint Index register to the Write Data Port register must be at least 100 ns. Table 28. Endpoint Index register: bit allocation Bit 7 Symbol 6 reserved 5 4 3 EP0SETUP 2 1 ENDPIDX[3:0] 0 DIR Reset - - 1 0 0 0 0 0 Bus reset - - unchanged 0 0 0 0 0 R/W R/W R/W R/W R/W R/W R/W R/W Access ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 29 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Table 29. Endpoint Index register: bit description Bit Symbol Description 7 to 6 - reserved 5 EP0SETUP Endpoint 0 Setup: Selects the SETUP buffer of endpoint 0. 0 — Data buffer 1 — SETUP buffer Must be logic 0 for access to endpoints other than set-up token buffer. 4 to 1 ENDPIDX[3:0] Endpoint Index: Selects the target endpoint for register access of buffer length, buffer status, control function, data port, endpoint type and MaxPacketSize. 0 DIR Direction: Sets the target endpoint as IN or OUT. 0 — Target endpoint refers to OUT (RX) FIFO 1 — Target endpoint refers to IN (TX) FIFO Table 30. Addressing of endpoint buffers Buffer name EP0SETUP ENDPIDX DIR SETUP 1 00h 0 Control OUT 0 00h 0 Control IN 0 00h 1 Data OUT 0 0Xh 0 Data IN 0 0Xh 1 8.3.2 Control Function register (address: 28h) The Control Function register performs the buffer management on endpoints. It consists of 1 byte, and the bit configuration is given in Table 31. Register bits can stall, clear or validate any enabled data endpoint. Before accessing this register, the Endpoint Index register must first be written to specify the target endpoint. Table 31. Control Function register: bit allocation Bit 7 Symbol 6 5 reserved 4 3 2 1 0 CLBUF VENDP DSEN STATUS STALL 0 0 0 0 0 Reset - - - Bus reset - - - 0 0 0 0 0 Access - - - R/W R/W W R/W R/W ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 30 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Table 32. Control Function register: bit description Bit Symbol Description 7 to 5 - reserved 4 CLBUF Clear Buffer: Logic 1 clears the TX or RX buffer of the indexed endpoint. The RX buffer is automatically cleared once the endpoint is completely read. This bit is set only when it is necessary to forcefully clear the buffer. Remark: If using double buffer, to clear both the buffers issue the CLBUF command two times. For details on clearing buffers, refer to Ref. 4 “ISP1582/83 and ISP1761 clearing an IN buffer (AN10045)”. 3 VENDP Validate Endpoint: Logic 1 validates data in the TX FIFO of an IN endpoint to send on the next IN token. In general, the endpoint is automatically validated when its FIFO byte count has reached endpoint MaxPacketSize. This bit is set only when it is necessary to validate the endpoint with the FIFO byte count, which is below endpoint MaxPacketSize. Remark: Use either bit VENDP or register Buffer Length to validate endpoint FIFO with FIFO bytes. 2 DSEN Data Stage Enable: This bit controls the response of the ISP1582 to a control transfer. After the completion of the set-up stage, firmware must determine whether a data stage is required. For control OUT, firmware will set this bit and the ISP1582 goes into the data stage. Otherwise, the ISP1582 will NAK the data stage transfer. For control IN, firmware will set this bit before writing data to the TX FIFO and validate the endpoint. If no data stage is required, firmware can immediately set the STATUS bit after the set-up stage. Remark: The DSEN bit is cleared once the OUT token is acknowledged by the device and the IN token is acknowledged by the PC host. This bit cannot be read back and reading this bit will return logic 0. 1 STATUS Status Acknowledge: Only applicable for control IN or OUT. This bit controls the generation of ACK or NAK during the status stage of a SETUP transfer. It is automatically cleared when the status stage is completed, or when a SETUP token is received. No interrupt signal will be generated. 0 — Sends NAK 1 — Sends an empty packet following the IN token (peripheral-to-host) or ACK following the OUT token (host-to-peripheral). Remark: The STATUS bit is cleared to zero once the zero-length packet is acknowledged by the device or the PC host. Remark: Data transfers preceding the status stage must first be fully completed before the STATUS bit can be set. 0 STALL Stall Endpoint: Logic 1 stalls the indexed endpoint. This bit is not applicable for isochronous transfers. Remark: Stalling a data endpoint will confuse the Data Toggle bit about the stalled endpoint because the internal logic picks up from where it is stalled. Therefore, the Data Toggle bit must be reset by disabling and re-enabling the corresponding endpoint (by setting bit ENABLE to logic 0, followed by logic 1 in the Endpoint Type register) to reset the PID. 8.3.3 Data Port register (address: 20h) This 2-byte register provides direct access for a microcontroller to the FIFO of the indexed endpoint. The bit allocation is shown in Table 33. ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 31 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Peripheral-to-host (IN endpoint): After each write action, an internal counter is auto incremented by two to the next location in the TX FIFO. When all bytes are written (FIFO byte count = endpoint MaxPacketSize), the buffer is automatically validated. The data packet will then be sent on the next IN token. When it is necessary to validate the endpoint whose byte count is less than MaxPacketSize, it can be done using the Control Function register (bit VENDP) or the Buffer Length register. Remark: The buffer can automatically be validated by using the Buffer Length register (see Table 35). Host-to-peripheral (OUT endpoint): After each read action, an internal counter is auto decremented by two to the next location in the RX FIFO. When all bytes are read, buffer contents are automatically cleared. A new data packet can then be received on the next OUT token. Buffer contents can also be cleared using the Control Function register (bit CLBUF), when it is necessary to forcefully clear contents. Remark: The delay time from the Write Endpoint Index register to the Read Data Port register must be at least 190 ns. Remark: The delay time from the Write Endpoint Index register to the Write Data Port register must be at least 100 ns. Table 33. Data Port register: bit allocation Bit 15 14 13 Symbol 12 11 10 9 8 DATAPORT[15:8] Reset 0 0 0 0 0 0 0 0 Bus reset 0 0 0 0 0 0 0 0 R/W R/W R/W R/W R/W R/W R/W R/W 7 6 5 4 3 2 1 0 Reset 0 0 0 0 0 0 0 0 Bus reset 0 0 0 0 0 0 0 0 R/W R/W R/W R/W R/W R/W R/W R/W Access Bit Symbol DATAPORT[7:0] Access Table 34. Bit Data Port register: bit description Symbol Description 15 to 8 DATAPORT[15:8] data (upper byte) 7 to 0 DATAPORT[7:0] data (lower byte) 8.3.4 Buffer Length register (address: 1Ch) This register determines the current packet size (DATACOUNT) of the indexed endpoint FIFO. The bit allocation is given in Table 35. The Buffer Length register is automatically loaded with the FIFO size, when the Endpoint MaxPacketSize register is written (see Table 39). A smaller value can be written when required. After a bus reset, the Buffer Length register is made zero. ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 32 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller IN endpoint: When data transfer is performed in multiples of MaxPacketSize, the Buffer Length register is not significant. This register is useful only when transferring data that is not a multiple of MaxPacketSize. The following two examples demonstrate the significance of the Buffer Length register. Example 1: Consider that the transfer size is 512 bytes and the MaxPacketSize is programmed as 64 bytes, the Buffer Length register need not be filled. This is because the transfer size is a multiple of MaxPacketSize, and MaxPacketSize packets will be automatically validated because the last packet is also of MaxPacketSize. Example 2: Consider that the transfer size is 510 bytes and the MaxPacketSize is programmed as 64 bytes, the Buffer Length register must be filled with 62 bytes just before the microprocessor writes the last packet of 62 bytes. This ensures that the last packet, which is a short packet of 62 bytes, is automatically validated. Use bit VENDP in the Control register if you are not using the Buffer Length register. This is applicable only to the PIO mode access. OUT endpoint: The DATACOUNT value is automatically initialized to the number of data bytes sent by the host on each ACK. Remark: When using a 16-bit microprocessor bus, the last byte of an odd-sized packet is output as the lower byte (LSByte). Remark: Buffer Length is valid only after an interrupt is generated for the OUT endpoint. Table 35. Buffer Length register: bit allocation Bit 15 14 13 Symbol 12 11 10 9 8 DATACOUNT[15:8] Reset 0 0 0 0 0 0 0 0 Bus reset 0 0 0 0 0 0 0 0 R/W R/W R/W R/W R/W R/W R/W R/W 7 6 5 4 3 2 1 0 Reset 0 0 0 0 0 0 0 0 Bus reset 0 0 0 0 0 0 0 0 R/W R/W R/W R/W R/W R/W R/W R/W Access Bit Symbol DATACOUNT[7:0] Access Table 36. Buffer Length register: bit description Bit Symbol Description 15 to 0 DATACOUNT[15:0] Data Count: Determines the current packet size of the indexed endpoint FIFO. 8.3.5 Buffer Status register (address: 1Eh) This register is accessed using index. The endpoint index must first be set before accessing this register for the corresponding endpoint. It reflects the status of the double buffered endpoint FIFO. Remark: This register is not applicable to the control endpoint. ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 33 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Remark: For endpoint IN data transfer, firmware must ensure a 200 ns delay between writing of the data packet and reading the Buffer Status register. For endpoint OUT data transfer, firmware must also ensure a 200 ns delay between receiving the endpoint interrupt and reading the Buffer Status register. For more information, refer to Ref. 3 “Using ISP1582/3 in a composite device application with alternate settings (AN10071)”. Table 37 shows the bit allocation of the Buffer Status register. Table 37. Buffer Status register: bit allocation Bit 7 6 5 4 3 2 Reset - - - - - - Bus reset - - - - - Access - - - - - Symbol 1 0 BUF1 BUF0 0 0 - 0 0 - R R reserved Table 38. Buffer Status register: bit description Bit Symbol Description 7 to 2 - reserved 1 to 0 BUF[1:0] Buffer: 00 — The buffers are not filled. 01 — One of the buffers is filled. 10 — One of the buffers is filled. 11 — Both the buffers are filled. 8.3.6 Endpoint MaxPacketSize register (address: 04h) This register determines the maximum packet size for all endpoints, except set-up token buffer, control IN and control OUT. The register contains 2 bytes, and the bit allocation is given in Table 39. Each time the register is written, the Buffer Length register of the corresponding endpoint is re-initialized to the FFOSZ field value. Bits NTRANS control the number of transactions allowed in a single microframe (for high-speed isochronous and interrupt endpoints only). Table 39. Endpoint MaxPacketSize register: bit allocation Bit 15 Symbol 14 13 reserved 12 11 10 NTRANS[1:0] 0 8 FFOSZ[10:8] Reset - - - Bus reset - - - 0 0 0 0 0 Access - - - R/W R/W R/W R/W R/W Bit 7 6 5 4 3 2 1 0 Symbol 0 9 0 0 0 FFOSZ[7:0] Reset 0 0 0 0 0 0 0 0 Bus reset 0 0 0 0 0 0 0 0 R/W R/W R/W R/W R/W R/W R/W R/W Access ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 34 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Table 40. Endpoint MaxPacketSize register: bit description Bit Symbol Description 15 to 13 - reserved 12 to 11 NTRANS[1:0] Number of Transactions: HS mode only. 00 — 1 packet per microframe 01 — 2 packets per microframe 10 — 3 packets per microframe 11 — reserved These bits are applicable only for isochronous or interrupt transactions. 10 to 0 FFOSZ[10:0] FIFO Size: Sets the FIFO size, in bytes, for the indexed endpoint. Applies to both high-speed and full-speed operations. The ISP1582 supports all the transfers given in Ref. 1 “Universal Serial Bus Specification Rev. 2.0”. Each programmable FIFO can independently be configured using its Endpoint MaxPacketSize register (R/W: 04h), but the total physical size of all enabled endpoints (IN plus OUT) including set-up token buffer, control IN and control OUT, must not exceed 8192 bytes. 8.3.7 Endpoint Type register (address: 08h) This register sets the endpoint type of the indexed endpoint: isochronous, bulk or interrupt. It also serves to enable the endpoint and configure it for double buffering. Automatic generation of an empty packet for a zero-length TX buffer can be disabled using bit NOEMPKT. The register contains 2 bytes, and the bit allocation is shown in Table 41. Table 41. Endpoint Type register: bit allocation Bit 15 14 13 12 11 10 9 8 Reset - - - - - - - - Bus reset - - - - - - - - Access - - - - - - - - Bit 7 6 5 1 Symbol reserved Symbol reserved 4 3 2 NOEMPKT ENABLE DBLBUF 0 ENDPTYP[1:0] Reset - - - 0 0 0 0 0 Bus reset - - - 0 0 0 0 0 Access - - - R/W R/W R/W R/W R/W ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 35 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Table 42. Endpoint Type register: bit description Bit Symbol Description 15 to 5 - reserved 4 NOEMPKT No Empty Packet: Logic 0 causes the ISP1582 to return a null length packet for the IN token after the DMA IN transfer is complete. For the IN DMA transfer, which does not require a null length packet after DMA completion, set to logic 1 to disable the generation of the null length packet. 3 ENABLE Endpoint Enable: Logic 1 enables the FIFO of the indexed endpoint. The memory size is allocated as specified in the Endpoint MaxPacketSize register. Logic 0 disables the FIFO. Remark: Stalling a data endpoint will confuse the Data Toggle bit on the stalled endpoint because the internal logic picks up from where it has stalled. Therefore, the Data Toggle bit must be reset by disabling and re-enabling the corresponding endpoint (by setting bit ENABLE to logic 0 or logic 1 in the Endpoint Type register) to reset the PID. 2 DBLBUF Double Buffering: Logic 1 enables double buffering for the indexed endpoint. Logic 0 disables double buffering. Remark: When performing a write to two empty buffers, ensure that a minimum of 200 ns delay is provided from the last write of the first buffer to the first write of the second buffer. Otherwise, the first few data bytes may not be written to the second buffer, causing data corruption. 1 to 0 ENDPTYP[1:0] Endpoint Type: These bits select the endpoint type as follows. 00 — Not used 01 — Isochronous 10 — Bulk 11 — Interrupt 8.4 DMA registers The Generic DMA (GDMA) transfer can be done by writing the proper opcode in the DMA Command register. Control bits are given in Table 43. GDMA read/write (opcode = 00h/01h) for GDMA mode: Depending on the MODE[1:0] bits set in the DMA configuration register, the DACK, DIOR or DIOW signal strobes data. These signals are driven by the external DMA controller. GDMA mode can operate in either counter mode or EOT-only mode. In counter mode, bit DIS_XFER_CNT in the DMA Configuration register must be set to logic 0. The DMA Transfer Counter register must be programmed before any DMA command is issued. The DMA transfer counter is set by writing from the LSByte to the MSByte (address: 34h to 37h). The DMA transfer count is internally updated only after the MSByte is written. Once the DMA transfer is started, the transfer counter starts decrementing and on reaching 0, bit DMA_XFER_OK is set and an interrupt is generated by the ISP1582. If the DMA master wishes to terminate the DMA transfer, it can issue an EOT signal to the ISP1582. This EOT signal overrides the transfer counter and can terminate the DMA transfer at any time. ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 36 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller In EOT-only mode, DIS_XFER_CNT must be set to logic 1. Although the DMA transfer counter can still be programmed, it will not have any effect on the DMA transfer. The DMA transfer will start once the DMA command is issued. Any of the following three ways will terminate this DMA transfer: • Detecting an external EOT • Detecting an internal EOT (short packet on an OUT token) • Issuing a GDMA stop command There are three interrupts programmable to differentiate the method of DMA termination: bits INT_EOT, EXT_EOT and DMA_XFER_OK in the DMA Interrupt Reason register. For details, see Table 55. Table 43. Control bits for GDMA read/write (opcode = 00h/01h) Control bits Description Reference DMA Configuration register MODE[1:0] determines the active read/write data strobe signals WIDTH selects the DMA bus width: 8 or 16 bits DIS_XFER_CNT disables the use of the DMA Transfer Counter Table 49 DMA Hardware register Table 51 EOT_POL selects the polarity of the EOT signal ENDIAN[1:0] determines whether the data is to be byte swapped or normal; applicable only in 16-bit mode ACK_POL, DREQ_POL, WRITE_POL, READ_POL select polarity of DMA handshake signals Remark: The DMA bus defaults to 3-state, until a DMA command is executed. All the other control signals are not 3-stated. 8.4.1 DMA Command register (address: 30h) The DMA Command register is a 1-byte register (for bit allocation, see Table 44) that initiates all DMA transfer activity on the DMA controller. The register is write-only: reading it will return FFh. Remark: The DMA bus will be in 3-state, until a DMA command is executed. Table 44. DMA Command register: bit allocation Bit 7 6 5 Symbol 4 3 2 1 0 DMA_CMD[7:0] Reset 1 1 1 1 1 1 1 1 Bus reset 1 1 1 1 1 1 1 1 Access W W W W W W W W Table 45. DMA Command register: bit description Bit Symbol Description 7 to 0 DMA_CMD[7:0] DMA command code; see Table 46. ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 37 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Table 46. DMA commands Code Name Description 00h GDMA Read Generic DMA IN token transfer: Data is transferred from the external DMA bus to the internal buffer. Strobe: DIOW by the external DMA controller. 01h GDMA Write Generic DMA OUT token transfer: Data is transferred from the internal buffer to the external DMA bus. Strobe: DIOR by the external DMA controller. 02h to 0Dh - reserved 0Eh Validate Buffer Validate Buffer (for debugging only): Request from the microcontroller to validate the endpoint buffer, following a DMA-to-USB data transfer. 0Fh Clear Buffer Clear Buffer: Request from the microcontroller to clear the endpoint buffer, after a DMA-to-USB data transfer. Logic 1 clears the TX buffer of the indexed endpoint; the RX buffer is not affected. The TX buffer is automatically cleared once data is sent on the USB bus. This bit is set only when it is necessary to forcefully clear the buffer. Remark: If using double buffer, to clear both the buffers issue the Clear Buffer command two times, that is, set and clear this bit two times. 10h - reserved 11h Reset DMA Reset DMA: Initializes the DMA core to its power-on reset state. Remark: When the DMA core is reset during the Reset DMA command, the DREQ, DACK, DIOW and DIOR handshake pins will temporarily be asserted. This can confuse the external DMA controller. To prevent this, start the external DMA controller only after the DMA reset. 12h - reserved 13h GDMA Stop GDMA stop: This command stops the GDMA data transfer. Any data in the OUT endpoint that is not transferred by the DMA will remain in the buffer. The FIFO data for the IN endpoint will be written to the endpoint buffer. An interrupt bit will be set to indicate the completion of the DMA Stop command. Remark: For the DMA OUT transfer, if the DMA Burst Counter register is programmed to some value, for example 512 bytes, and if a GDMA Stop command is issued in the middle of a transfer, the transfer will continue until the end of the burst size (512 bytes). Issuing a GDMA stop command does not allow the ISP1582 to stop in the middle of the burst. It can only be stopped in between bursts. 14h to FFh - reserved 8.4.2 DMA Transfer Counter register (address: 34h) This 4-byte register sets up the total byte count for a DMA transfer (DMACR). It indicates the remaining number of bytes left for transfer. The bit allocation is given in Table 47. For IN endpoint — Because there is a FIFO in the ISP1582 DMA controller, some data may remain in the FIFO during the DMA transfer. The maximum FIFO size is 8 bytes, and the maximum delay time for data to be shifted to endpoint buffer is 60 ns. For OUT endpoint — Data will not be cleared from the endpoint buffer, until all the data is read from the DMA FIFO. If the DMA counter is disabled in the DMA transfer, it will still decrement and rollover when it reaches zero. Table 47. DMA Transfer Counter register: bit allocation Bit Symbol 31 30 29 28 27 25 24 DMACR4 = DMACR[31:24] ISP1582_7 Product data sheet 26 © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 38 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Table 47. DMA Transfer Counter register: bit allocation …continued Bit 31 30 29 28 27 26 25 24 Reset 0 0 0 0 0 0 0 0 Bus reset 0 0 0 0 0 0 0 0 R/W R/W R/W R/W R/W R/W R/W R/W 23 22 21 20 19 18 17 16 Access Bit Symbol DMACR3 = DMACR[23:16] Reset 0 0 0 0 0 0 0 0 Bus reset 0 0 0 0 0 0 0 0 R/W R/W R/W R/W R/W R/W R/W R/W 15 14 13 12 11 10 9 8 0 0 0 Access Bit Symbol DMACR2 = DMACR[15:8] Reset 0 Bus reset Access 0 0 0 0 0 0 0 0 0 0 0 0 R/W R/W R/W R/W R/W R/W R/W R/W 7 6 5 4 3 2 1 0 Bit Symbol DMACR1 = DMACR[7:0] Reset 0 0 0 0 0 0 0 0 Bus reset 0 0 0 0 0 0 0 0 R/W R/W R/W R/W R/W R/W R/W R/W Access Table 48. DMA Transfer Counter register: bit description Bit Symbol Description 31 to 24 DMACR4 = DMACR[31:24] DMA transfer counter byte 4 (MSByte) 23 to 16 DMACR3 = DMACR[23:16] DMA transfer counter byte 3 15 to 8 DMACR2 = DMACR[15:8] DMA transfer counter byte 2 7 to 0 DMACR1 = DMACR[7:0] DMA transfer counter byte 1 (LSByte) 8.4.3 DMA Configuration register (address: 38h) This register defines the DMA configuration for GDMA mode. The DMA Configuration register consists of 2 bytes. The bit allocation is given in Table 49. Table 49. DMA Configuration register: bit allocation Bit 15 14 13 12 Symbol 11 10 9 8 reserved Reset - - - - - - - - Bus reset - - - - - - - - Access - - - - - - - - Bit 7 6 5 4 3 2 1 0 reserved WIDTH Symbol DIS_ XFER_CNT reserved MODE[1:0] Reset 0 - - - 0 0 - 1 Bus reset 0 - - - 0 0 - 1 R/W - - - R/W R/W - R/W Access ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 39 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Table 50. DMA Configuration register: bit description Bit Symbol Description[1] 15 to 8 - reserved 7 DIS_XFER_CNT Disable Transfer Count: Logic 1 disables the DMA Transfer Counter (see Table 47). 6 to 4 - reserved 3 to 2 MODE[1:0] Mode: These bits affect GDMA handshake signals. 00 — DIOW strobes data from the DMA bus into the ISP1582; DIOR puts data from the ISP1582 on the DMA bus. 01 — DACK strobes data from the DMA bus into the ISP1582; DIOR puts data from the ISP1582 on the DMA bus. 10 — DACK strobes data from the DMA bus into the ISP1582 and also puts data from the ISP1582 on the DMA bus. 11 — reserved 1 - reserved 0 WIDTH Width: This bit selects the DMA bus width. 0 — 8-bit data bus 1 — 16-bit data bus [1] The DREQ pin will be driven only after performing a write access to the DMA Configuration register (that is, after configuring the DMA Configuration register). 8.4.4 DMA Hardware register (address: 3Ch) The DMA Hardware register consists of 1 byte. The bit allocation is shown in Table 51. This register determines the polarity of bus control signals (EOT, DACK, DREQ, DIOR and DIOW). It also controls whether the upper and lower parts of the data bus are swapped (bits ENDIAN[1:0]). Table 51. DMA Hardware register: bit allocation Bit Symbol 7 6 ENDIAN[1:0] 5 4 3 2 1 0 EOT_POL reserved ACK_POL DREQ_ POL WRITE_ POL READ_ POL Reset 0 0 0 - 0 1 0 0 Bus reset 0 0 0 - 0 1 0 0 R/W R/W R/W - R/W R/W R/W R/W Access ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 40 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Table 52. DMA Hardware register: bit description Bit Symbol Description 7 to 6 ENDIAN[1:0] Endian: These bits determine whether the data bus is swapped between the internal RAM and the DMA bus. 00 — Normal data representation; 16-bit bus: MSByte on DATA[15:8], LSByte on DATA[7:0] 01 — Swapped data representation; 16-bit bus: MSByte on DATA[7:0], LSByte on DATA[15:8] 10 — reserved 11 — reserved Remark: While operating with the 8-bit data bus, bits ENDIAN[1:0] must always be set to 00b. 5 EOT_POL EOT Polarity: Selects the polarity of the End-Of-Transfer input. 0 — EOT is active LOW 1 — EOT is active HIGH 4 - reserved; must be set to logic 0. 3 ACK_POL Acknowledgment Polarity: Selects the DMA acknowledgment polarity. 0 — DACK is active LOW 1 — DACK is active HIGH 2 DREQ_POL DREQ Polarity: Selects the DMA request polarity. 0 — DREQ is active LOW 1 — DREQ is active HIGH 1 WRITE_POL Write Polarity: Selects the DIOW strobe polarity. 0 — DIOW is active LOW 1 — DIOW is active HIGH 0 READ_POL Read Polarity: Selects the DIOR strobe polarity. 0 — DIOR is active LOW 1 — DIOR is active HIGH 8.4.5 DMA Interrupt Reason register (address: 50h) This 2-byte register shows the source(s) of DMA interrupt. Each bit is refreshed after a DMA command is executed. An interrupt source is cleared by writing logic 1 to the corresponding bit. On detecting the interrupt, the external microprocessor must read the DMA Interrupt Reason register and mask it with the corresponding bits in the DMA Interrupt Enable register to determine the source of the interrupt. The bit allocation is given in Table 53. Table 53. DMA Interrupt Reason register: bit allocation Bit Symbol 15 14 TEST3 13 reserved 12 11 10 9 8 GDMA_ STOP EXT_EOT INT_EOT reserved DMA_ XFER_OK Reset - - - 0 0 0 - 0 Bus reset - - - 0 0 0 - 0 Access R - - R/W R/W R/W R/W R/W ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 41 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Bit 7 6 5 4 3 2 1 0 Reset - - - - - - - - Bus reset - - - - - - - - Access - - - - - - - - Symbol reserved Table 54. DMA Interrupt Reason register: bit description Bit Symbol Description 15 TEST3 This bit is set when the DMA transfer for a packet (OUT transfer) terminates before the whole packet has been transferred. This bit is a status bit, and the corresponding mask bit of this register is always logic 0. Writing any value other than logic 0 has no effect. 14 to 13 - reserved 12 GDMA_STOP GDMA Stop: When the GDMA_STOP command is issued to DMA Command registers, it means the DMA transfer has successfully terminated. 11 EXT_EOT External EOT: Logic 1 indicates that an external EOT is detected. 10 INT_EOT Internal EOT: Logic 1 indicates that an internal EOT is detected; see Table 55. 9 - reserved 8 DMA_XFER_OK DMA Transfer OK: Logic 1 indicates that the DMA transfer is completed (DMA Transfer Counter has become zero). 7 to 0 - Table 55. reserved Internal EOT-functional relation with bit DMA_XFER_OK INT_EOT DMA_XFER_OK Description 1 0 During the DMA transfer, there is a premature termination with short packet. 1 1 DMA transfer is completed with short packet and the DMA transfer counter has reached 0. 0 1 DMA transfer is completed without any short packet and the DMA transfer counter has reached 0. 8.4.6 DMA Interrupt Enable register (address: 54h) This 2-byte register controls the interrupt generation of the source bits in the DMA Interrupt Reason register. The bit allocation is given in Table 56. The bit description is given in Table 54. Logic 1 enables the interrupt generation. After a bus reset, interrupt generation is disabled, with the values turning to logic 0. Table 56. DMA Interrupt Enable register: bit allocation Bit Symbol 15 14 TEST4 13 reserved 12 11 10 9 8 IE_GDMA_ STOP IE_EXT_ EOT IE_INT_ EOT reserved IE_DMA_ XFER_OK Reset - - - 0 0 0 0 0 Bus reset - - - 0 0 0 0 0 Access R - - R/W R/W R/W R/W R/W ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 42 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Bit 7 6 5 4 3 2 1 0 Reset 0 0 0 0 0 0 0 0 Bus reset 0 0 0 0 0 0 0 0 R/W R/W R/W R/W R/W R/W R/W R/W Symbol reserved Access 8.4.7 DMA Endpoint register (address: 58h) This 1-byte register selects a USB endpoint FIFO as a source or destination for DMA transfers. The bit allocation is given in Table 57. Table 57. DMA Endpoint register: bit allocation Bit 7 6 Symbol 5 4 3 2 reserved 1 EPIDX[2:0] 0 DMADIR Reset - - - - 0 0 0 0 Bus reset - - - - 0 0 0 0 Access - - - - R/W R/W R/W R/W Table 58. DMA Endpoint register: bit description Bit Symbol Description 7 to 4 - reserved 3 to 1 EPIDX[2:0] Endpoint Index: Selects the indicated endpoint for DMA access 0 DMADIR DMA Direction: 0 — Selects the RX/OUT FIFO for DMA read transfers 1 — Selects the TX/IN FIFO for DMA write transfers The DMA Endpoint register must not reference the endpoint that is indexed by the Endpoint Index register (2Ch) at any time. Doing so will result in data corruption. Therefore, if the DMA Endpoint register is unused, point it to an unused endpoint. If the DMA Endpoint register, however, is pointed to an active endpoint, the firmware must not reference the same endpoint on the Endpoint Index register. 8.4.8 DMA Burst Counter register (address: 64h) Table 59 shows the bit allocation of the 2-byte register. Table 59. DMA Burst Counter register: bit allocation Bit 15 Symbol 14 13 12 11 reserved 10 9 8 BURSTCOUNTER[12:8] Reset - - - 0 0 0 0 0 Bus reset - - - 0 0 0 0 0 Access - - - R/W R/W R/W R/W R/W Bit 7 6 5 4 3 2 1 0 0 1 0 Symbol Reset Bus reset Access BURSTCOUNTER[7:0] 0 0 0 0 0 0 0 0 0 0 0 1 0 R/W R/W R/W R/W R/W R/W R/W R/W ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 43 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Table 60. DMA Burst Counter register: bit description Bit Symbol Description 15 to 13 - reserved 12 to 0 BURST COUNTER [12:0] Burst Counter: This register defines the burst length. The counter must be programmed to be a multiple of two in 16-bit mode. The value of the burst counter must be programmed so that the burst counter is a factor of the buffer size. It is used to determine the assertion and deassertion of DREQ. 8.5 General registers 8.5.1 Interrupt register (address: 18h) The Interrupt register consists of 4 bytes. The bit allocation is given in Table 61. When a bit is set in the Interrupt register, it indicates that the hardware condition for an interrupt has occurred. When the Interrupt register content is nonzero, the INT output will be asserted corresponding to the Interrupt Enable register. On detecting the interrupt, the external microprocessor must read the Interrupt register and mask it with the corresponding bits in the Interrupt Enable register to determine the source of the interrupt. Each endpoint buffer has a dedicated interrupt bit (EPnTX, EPnRX). In addition, various bus states can generate an interrupt: resume, suspend, pseudo SOF, SOF and bus reset. The DMA controller only has one interrupt bit: the source for a DMA interrupt is shown in the DMA Interrupt Reason register. Each interrupt bit can individually be cleared by writing logic 1. The DMA Interrupt bit can be cleared by writing logic 1 to the related interrupt source bit in the DMA Interrupt Reason register, followed by writing logic 1 to the DMA bit of the Interrupt register. Table 61. Interrupt register: bit allocation Bit 31 30 29 Symbol 28 27 26 reserved 25 24 EP7TX EP7RX 0 0 Reset - - - - - - Bus reset - - - - - - 0 0 Access - - - - - - R/W R/W 23 22 21 20 19 18 17 16 EP6TX EP6RX EP5TX EP5RX EP4TX EP4RX EP3TX EP3RX Reset 0 0 0 0 0 0 0 0 Bus reset 0 0 0 0 0 0 0 0 R/W R/W R/W R/W R/W R/W R/W R/W 15 14 13 12 11 10 9 8 Bit Symbol Access Bit Symbol EP2TX EP2RX EP1TX EP1RX EP0TX EP0RX reserved EP0SETUP Reset 0 0 0 0 0 0 - 0 Bus reset 0 0 0 0 0 0 - 0 R/W R/W R/W R/W R/W R/W - R/W Access ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 44 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Bit Symbol 7 6 5 4 3 2 1 0 VBUS DMA HS_STAT RESUME SUSP PSOF SOF BRESET Reset 0 0 0 0 0 0 0 0 Bus reset 0 0 0 0 0 0 0 1 R/W R/W R/W R/W R/W R/W R/W R/W Access Table 62. Interrupt register: bit description Bit Symbol Description 31 to 26 - reserved 25 EP7TX logic 1 indicates the endpoint 7 TX buffer as interrupt source 24 EP7RX logic 1 indicates the endpoint 7 RX buffer as interrupt source 23 EP6TX logic 1 indicates the endpoint 6 TX buffer as interrupt source 22 EP6RX logic 1 indicates the endpoint 6 RX buffer as interrupt source 21 EP5TX logic 1 indicates the endpoint 5 TX buffer as interrupt source 20 EP5RX logic 1 indicates the endpoint 5 RX buffer as interrupt source 19 EP4TX logic 1 indicates the endpoint 4 TX buffer as interrupt source 18 EP4RX logic 1 indicates the endpoint 4 RX buffer as interrupt source 17 EP3TX logic 1 indicates the endpoint 3 TX buffer as interrupt source 16 EP3RX logic 1 indicates the endpoint 3 RX buffer as interrupt source. 15 EP2TX logic 1 indicates the endpoint 2 TX buffer as interrupt source 14 EP2RX logic 1 indicates the endpoint 2 RX buffer as interrupt source 13 EP1TX logic 1 indicates the endpoint 1 TX buffer as interrupt source 12 EP1RX logic 1 indicates the endpoint 1 RX buffer as interrupt source 11 EP0TX logic 1 indicates the endpoint 0 data TX buffer as interrupt source 10 EP0RX logic 1 indicates the endpoint 0 data RX buffer as interrupt source 9 - reserved 8 EP0SETUP logic 1 indicates that a SETUP token was received on endpoint 0 7 VBUS logic 1 indicates a transition from LOW to HIGH transition on VBUS 6 DMA DMA Status: Logic 1 indicates a change in the DMA Interrupt Reason register. 5 HS_STAT High-Speed Status: Logic 1 indicates a change from full-speed to high-speed mode (HS connection). This bit is not set when the system goes into full-speed suspend. 4 RESUME Resume Status: Logic 1 indicates that a status change from suspend to resume (active) was detected. 3 SUSP Suspend Status: Logic 1 indicates that a status change from active to suspend was detected on the bus. 2 PSOF Pseudo SOF Interrupt: Logic 1 indicates that a pseudo SOF or µSOF was received. Pseudo SOF is an internally generated clock signal (full-speed: 1 ms period, high-speed: 125 µs period) that is not synchronized to the USB bus SOF or µSOF. 1 SOF SOF Interrupt: Logic 1 indicates that a SOF or µSOF was received. 0 BRESET Bus Reset: Logic 1 indicates that a USB bus reset was detected. When bit OTG in the OTG register is set, BRESET will not be set; instead, this interrupt bit will report SE0 on DP and DM for 2 ms. ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 45 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller 8.5.2 Chip ID register (address: 70h) This read-only register contains the chip identification and hardware version numbers. Firmware must check this information to determine functions and features supported. The register contains 3 bytes, and the bit allocation is shown in Table 63. Table 63. Chip ID register: bit allocation Bit 23 22 21 20 18 17 16 Reset 0 0 0 1 0 1 0 1 Bus reset 0 0 0 1 0 1 0 1 Access R R R R R R R R Bit 15 14 13 12 11 10 9 8 Symbol 19 CHIPID[15:8] Symbol CHIPID[7:0] Reset 1 0 0 0 0 0 1 0 Bus reset 1 0 0 0 0 0 1 0 Access R R R R R R R R Bit 7 6 5 4 3 2 1 0 0 0 0 Symbol VERSION[7:0] Reset 0 0 1 1 0 Bus reset 0 0 1 1 0 0 0 0 Access R R R R R R R R Table 64. Chip ID register: bit description Bit Symbol Description 23 to 16 CHIPID[15:8] Chip ID: Lower byte (15h) 15 to 8 CHIPID[7:0] Chip ID: Upper byte (82h) 7 to 0 VERSION[7:0] Version: Version number (30h) 8.5.3 Frame Number register (address: 74h) This read-only register contains the frame number of the last successfully received Start-Of-Frame (SOF). The register contains 2 bytes, and the bit allocation is given in Table 65. In case of 8-bit access, the register content is returned lower byte first. Table 65. Frame Number register: bit allocation Bit 15 Symbol 14 13 reserved 12 11 10 MICROSOF[2:0] 9 8 SOFR[10:8] Reset - - 0 0 0 0 0 0 Bus reset - - 0 0 0 0 0 0 Access - - R R R R R R Bit 7 6 5 4 3 2 1 0 Symbol SOFR[7:0] Reset 0 0 0 0 0 0 0 0 Bus reset 0 0 0 0 0 0 0 0 Access R R R R R R R R ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 46 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Table 66. Frame Number register: bit description Bit Symbol Description 15 to 14 - reserved 13 to 11 MICROSOF[2:0] microframe number 10 to 0 SOFR[10:0] frame number 8.5.4 Scratch register (address: 78h) This 16-bit register can be used by the firmware to save and restore information. For example, the device status before it enters the suspend state. The bit allocation is given in Table 67. Table 67. Scratch register: bit allocation Bit 15 14 13 12 Symbol 11 10 9 8 0 0 0 0 SFIRH[7:0] Reset 0 Bus reset Access Bit 0 0 0 0 0 0 0 0 0 0 0 R/W R/W R/W R/W R/W R/W R/W R/W 7 6 5 4 3 2 1 0 Symbol SFIRL[7:0] Reset 0 0 0 0 0 0 0 0 Bus reset 0 0 0 0 0 0 0 0 R/W R/W R/W R/W R/W R/W R/W R/W Access Table 68. Scratch register: bit description Bit Symbol Description 15 to 8 SFIRH[7:0] Scratch firmware information register (higher byte) 7 to 0 SFIRL[7:0] Scratch firmware information register (lower byte) 8.5.5 Unlock Device register (address: 7Ch) To protect registers from getting corrupted when the ISP1582 goes into suspend, the write operation is disabled if bit PWRON in the Mode register is set to logic 0. In this case, when the chip resumes, the Unlock Device command must first be issued to this register before attempting to write to the rest of the registers. This is done by writing unlock code (AA37h) to this register. The bit allocation of the Unlock Device register is given in Table 69. Table 69. Unlock Device register: bit allocation Bit 15 14 13 Symbol 12 11 10 9 8 ULCODE[15:8] = AAh Reset not applicable Bus reset not applicable Access W W W W W W W W Bit 7 6 5 4 3 2 1 0 Symbol ULCODE[7:0] = 37h ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 47 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Bit 7 6 5 4 3 Reset not applicable Bus reset not applicable Access W W W Table 70. W W 2 1 0 W W W Unlock Device register: bit description Bit Symbol Description 15 to 0 ULCODE[15:0] Unlock Code: Writing data AA37h unlocks the internal registers and FIFOs for writing, following a resume. When bit PWRON in the Mode register is logic 1, the chip is powered. In such a case, you do not need to issue the Unlock command because the microprocessor is powered and therefore, the RD_N, WR_N and CS_N signals maintain their states. When bit PWRON is logic 0, the RD_N, WR_N and CS_N signals are floating because the microprocessor is not powered. To protect the ISP1582 registers from being corrupted during suspend, register write is locked when the chip goes into suspend. Therefore, you need to issue the Unlock command to unlock the ISP1582 registers. 8.5.6 Test Mode register (address: 84h) This 1-byte register allows the firmware to set pins DP and DM to predetermined states for testing purposes. The bit allocation is given in Table 71. Remark: Only one bit can be set to logic 1 at a time. This must be implemented for the Hi-Speed USB logo compliance testing. To exit test mode, power cycle is required. Table 71. Test Mode register: bit allocation Bit Symbol 7 FORCEHS Reset Bus reset 6 5 reserved 4 3 2 1 0 FORCEFS PRBS KSTATE JSTATE SE0_NAK 0 - - 0 0 0 0 0 unchanged - - unchanged 0 0 0 0 R/W - - R/W R/W R/W R/W R/W Access Table 72. Test Mode register: bit description Bit Symbol Description 7 FORCEHS Force High-Speed: Logic 1[1] forces the hardware to high-speed mode only and disables the chirp detection logic. 6 to 5 - reserved 4 FORCEFS Force Full-Speed: Logic 1[1] forces the physical layer to full-speed mode only and disables the chirp detection logic. 3 PRBS Predetermined Random Pattern: Logic 1[2] sets pins DP and DM to toggle in a predetermined random pattern. 2 KSTATE K-State: Logic 1[2] sets pins DP and DM to the K state. 1 JSTATE J-State: Logic 1[2] sets pins DP and DM to the J state. 0 SE0_NAK SE0 NAK: Logic 1[2] sets pins DP and DM to a high-speed quiescent state. The device only responds to a valid high-speed IN token with a NAK. [1] Either FORCEHS or FORCEFS must be set at a time. [2] Of the four bits (PRBS, KSTATE, JSTATE and SE0_NAK), only one bit must be set at a time. ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 48 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller 9. Limiting values Table 73. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter VCC supply voltage VCC(I/O) input/output supply voltage VI input voltage Ilu latch-up current Vesd electrostatic discharge voltage Tstg storage temperature [1] Conditions Min Max Unit −0.5 +4.6 V −0.5 +4.6 V −0.5 VCC + 0.5 V VI < 0 V or VI > VCC - 100 mA ILI < 1 µA −2000 +2000 V −40 +125 °C [1] The maximum value for 5 V tolerant pins is 6 V. 10. Recommended operating conditions Table 74. Recommended operating conditions Symbol Parameter Min Typ Max Unit VCC supply voltage Conditions 3.0 - 3.6 V VCC(I/O) input/output supply voltage VCC - VCC V VI input voltage VCC = 3.3 V 0 - 3.3 V VIA(I/O) input voltage on analog I/O pins on pins DP and DM 0 - 3.6 V V(pu)OD open-drain pull-up voltage 0 - VCC V Tamb ambient temperature −40 - +85 °C Tj junction temperature −40 - +125 °C 11. Static characteristics Table 75. Static characteristics: supply pins VCC = 3.3 V ± 0.3 V; VGND = 0 V; Tamb = −40 °C to +85 °C; typical values at Tamb = 25 °C; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit 3.0 3.3 3.6 V high-speed - 45 60 mA full-speed - 17 25 mA VCC = 3.3 V - 160 - µA Supply voltage VCC supply voltage ICC supply current ICC(susp) suspend supply current VCC = 3.3 V I/O pad supply voltage VCC(I/O) input/output supply voltage ICC(I/O) supply current on pin VCC(I/O) [1] VCC VCC VCC V - 3 - mA 1.65 1.8 1.95 V Regulated supply voltage VCC(1V8) [1] supply voltage (1.8 V) with voltage converter ICC(I/O) test condition: device set up under the test mode vector and I/O is subjected to external conditions. ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 49 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Table 76. Static characteristics: digital pins VCC(I/O) = VCC; VGND = 0 V; Tamb = −40 °C to +85 °C; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit - 0.3VCC(I/O) V - V Input levels VIL LOW-level input voltage - VIH HIGH-level input voltage 0.7VCC(I/O) - Output levels VOL LOW-level output voltage IOL = rated drive - VOH HIGH-level output voltage IOH = rated drive 0.8VCC(I/O) - - - 0.15VCC(I/O) V V −5 +5 µA Leakage current [1] [1] input leakage current ILI - This value is applicable to transistor input only. The value will be different if internal pull-up or pull-down resistors are used. Table 77. Static characteristics: OTG detection VCC(I/O) = VCC; VGND = 0 V; Tamb = −40 °C to +85 °C; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit Charging and discharging resistor RDN(VBUS) pull-down resistance on pin VBUS only when bit DISCV is set in the OTG register 680 800 1030 Ω RUP(DP) pull-up resistance on pin DP only when bit DP is set in the OTG register 300 550 780 Ω Comparator levels VBVALID VBUS valid detection 2.0 - 4.0 V VSESEND VBUS B-session end detection 0.2 - 0.8 V Min Typ Max Unit Table 78. Static characteristics: analog I/O pins DP and DM VCC = 3.3 V ± 0.3 V; VGND = 0 V; Tamb = −40 °C to +85 °C; unless otherwise specified.[1] Symbol Parameter Conditions Input levels VDI differential input sensitivity voltage |VI(DP) − VI(DM)| 0.2 - - V VCM differential common mode voltage range 0.8 - 2.5 V includes VDI range VSE single-ended receiver threshold 0.8 - 2.0 V VIL LOW-level input voltage - - 0.8 V VIH HIGH-level input voltage 2.0 - - V Schmitt-trigger inputs Vth(LH) positive-going threshold voltage 1.4 - 1.9 V Vth(HL) negative-going threshold voltage 0.9 - 1.5 V Vhys hysteresis voltage 0.4 - 0.7 V Output levels VOL LOW-level output voltage RL = 1.5 kΩ to 3.6 V - - 0.4 V VOH HIGH-level output voltage RL = 15 kΩ to GND 2.8 - 3.6 V 0 V < VI < 3.3 V −10 - +10 µA Leakage current ILZ OFF-state leakage current ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 50 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Table 78. Static characteristics: analog I/O pins DP and DM …continued VCC = 3.3 V ± 0.3 V; VGND = 0 V; Tamb = −40 °C to +85 °C; unless otherwise specified.[1] Symbol Parameter Conditions Min Typ Max Unit input capacitance pin to GND - - 10 pF ZDRV driver output impedance for driver which is not high-speed capable steady-state drive 40.5 - 49.5 Ω ZINP input impedance exclusive of pull-up/pull-down (for low-/full-speed) 10 - - MΩ Min Typ Max Unit 500 - - µs Capacitance Cin Resistance [1] Pin DP is the USB positive data pin, and pin DM is the USB negative data pin. 12. Dynamic characteristics Table 79. Dynamic characteristics VCC = 3.3 V ± 0.3 V; VGND = 0 V; Tamb = −40 °C to +85 °C; unless otherwise specified. Symbol Parameter Conditions Reset tW(RESET_N) external RESET_N pulse width crystal oscillator running Crystal oscillator fXTAL1 frequency on pin XTAL1 - 12 - MHz RS series resistance - - 100 Ω CL load capacitance - 18 - pF External clock input VI input voltage 1.65 1.8 1.95 V tJ external clock jitter - - 500 ps δ clock duty cycle 45 50 55 % tr rise time - - 3 ns tf fall time - - 3 ns Table 80. Dynamic characteristics: analog I/O pins DP and DM VCC = 3.3 V ± 0.3 V; VGND = 0 V; Tamb = −40 °C to +85 °C; CL = 50 pF; RPU = 1.5 kΩ on DP to VTERM; test circuit of Figure 23; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit Driver characteristics Full-speed mode tFR rise time CL = 50 pF; 10 % to 90 % of |VOH − VOL| 4 - 20 ns tFF fall time CL = 50 pF; 90 % to 10 % of |VOH − VOL| 4 - 20 ns FRFM differential rise time/fall time matching tFR/tFF 90 - 111.11 % VCRS output signal crossover voltage 1.3 - 2.0 V 500 - - ps [1] [1][2] High-speed mode tHSR rise time (10 % to 90 %) with captive cable ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 51 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Table 80. Dynamic characteristics: analog I/O pins DP and DM …continued VCC = 3.3 V ± 0.3 V; VGND = 0 V; Tamb = −40 °C to +85 °C; CL = 50 pF; RPU = 1.5 kΩ on DP to VTERM; test circuit of Figure 23; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit tHSF with captive cable 500 - - ps fall time (10 % to 90 %) Data source timing Full-speed mode see Figure 13 [2] 160 - 175 ns see Figure 13 [2] −2 - +5 ns see Figure 14 [2] −18.5 - +18.5 ns tJR2 receiver jitter for paired transitions see Figure 14 [2] −9 - +9 ns tFEOPR receiver SE0 interval of EOP accepted as EOP; see Figure 13 [2] 82 - - ns rejected as EOP; see Figure 15 [2] - - 14 ns tFEOPT tFDEOP source SE0 interval of EOP source jitter for differential transition to SE0 transition Receiver timing Full-speed mode receiver jitter to next transition tJR1 width of SE0 interval during differential transition tFST [1] Excluding the first transition from the idle state. [2] Characterized only, not tested. Limits guaranteed by design. TPERIOD +3.3 V crossover point extended crossover point differential data lines 0V differential data to SE0/EOP skew N × TPERIOD + t DEOP source EOP width: t EOPT receiver EOP width: t EOPR mgr776 TPERIOD is the bit duration corresponding to the USB data rate. Full-speed timing symbols have a subscript prefix ‘F’, low-speed timing symbols have a prefix 'L'. Fig 13. Source differential data-to-EOP transition skew and EOP width ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 52 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller TPERIOD +3.3 V differential data lines 0V t JR t JR1 t JR2 mgr871 consecutive transitions N × TPERIOD + t JR1 paired transitions N × TPERIOD + t JR2 TPERIOD is the bit duration corresponding to the USB data rate. Fig 14. Receiver differential data jitter t FST +3.3 V VIH(min) differential data lines 0V mgr872 Fig 15. Receiver SE0 width tolerance 12.1 Register access timing Table 81. Register access timing parameters: separate address and data buses VCC(I/O) = VCC = 3.3 V; VGND = 0 V; Tamb = −40 °C to +85 °C; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit Reading tRLRH RD_N LOW pulse width > tRLDV - - ns tAVRL address set-up time before RD_N LOW 0 - - ns tRHAX address hold time after RD_N HIGH 0 - - ns tRLDV RD_N LOW to data valid delay - - 26 ns tRHDZ RD_N HIGH to data outputs three-state delay 0 - 15 ns tRHSH RD_N HIGH to CS_N HIGH delay 0 - - ns tSLRL CS_N LOW to RD_N LOW delay 2 - - ns Writing tWLWH WR_N LOW pulse width 15 - - ns tAVWL address set-up time before WR_N LOW 0 - - ns tWHAX address hold time after WR_N HIGH 0 - - ns tDVWH data set-up time before WR_N HIGH 11 - - ns tWHDZ data hold time after WR_N HIGH 5 - - ns ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 53 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Table 81. Register access timing parameters: separate address and data buses …continued VCC(I/O) = VCC = 3.3 V; VGND = 0 V; Tamb = −40 °C to +85 °C; unless otherwise specified. Symbol Parameter tWHSH tSLWL Conditions Min Typ Max Unit WR_N HIGH to CS_N HIGH delay 0 - - ns CS_N LOW to WR_N LOW delay 2 - - ns Tcy(RW) read or write cycle time 50 - - ns tWHRL WR_N HIGH to RD_N LOW time 91 - - ns General Tcy(RW) tWHSH tSLWL tRHSH CS_N tWHAX tRHAX tSLRL A[7:0] tRLDV tRHDZ (read) DATA[15:0] tAVRL tRLRH RD_N tWHDZ tAVWL (write) DATA[15:0] tDVWH WR_N tWLWH 004aaa276 Fig 16. Register access timing: separate address and data buses WR_N RD_N tWHRL 004aab064 Applies only to write followed by read to the same or different registers. Fig 17. ISP1582 ready signal timing ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 54 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller 12.2 DMA timing Table 82. GDMA mode timing parameters VCC(I/O) = VCC = 3.3 V; VGND = 0 V; Tamb = −40 °C to +85 °C; unless otherwise specified. Symbol Parameter Tcy1 Conditions Min Typ Max Unit read or write cycle time 75 - - ns tsu1 DREQ set-up time before first DACK on 10 - - ns td1 DREQ on delay after last strobe off 33.33 - - ns th1 DREQ hold time after last strobe on 0 - 53 ns tw1 DIOR or DIOW pulse width 39 - 600 ns tw2 DIOR/DIOW recovery time 36 - - ns td2 read data valid delay after strobe on - - 20 ns th2 read data hold time after strobe off - - 5 ns th3 write data hold time after strobe off 1 - - ns tsu2 write data set-up time before strobe off 10 - - ns tsu3 DACK set-up time before DIOR/DIOW assertion 0 - - ns ta1 DACK deassertion after DIOR/DIOW deassertion 0 - 30 ns DREQ(2) tsu1 tw1 Tcy1 th1 DACK(1) td1 tsu3 DIOR or DIOW(1) tw2 th2 td2 ta1 (read) DATA[15:0] tsu2 th3 (write) DATA[15:0] mgt500 DREQ is continuously asserted, until the last transfer is done or the FIFO is full. Data strobes: DIOR (read) and DIOW (write). (1) Programmable polarity: shown as active LOW. (2) Programmable polarity: shown as active HIGH. Fig 18. GDMA mode timing (bits MODE[1:0] = 00) ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 55 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller DREQ(2) tsu3 tw1 tsu1 Tcy1 td1 th1 DACK(1) td2 ta1 DIOR or DIOW(1) th2 (read) DATA[15:0] th3 tsu2 (write) DATA[15:0] mgt502 DREQ is asserted for every transfer. Data strobes: DIOR (read) and DACK (write). (1) Programmable polarity: shown as active LOW. (2) Programmable polarity: shown as active HIGH. Fig 19. GDMA mode timing (bits MODE[1:0] = 01) DREQ(2) tsu1 tw1 Tcy1 th1 DACK(1) tw2 td2 DIOR or DIOW(1) td1 HIGH th2 (read) DATA[15:0] tsu2 th3 (write) DATA[15:0] mgt501 DREQ is continuously asserted, until the last transfer is done or the FIFO is full. Data strobe: DACK (read/write). (1) Programmable polarity: shown as active LOW. (2) Programmable polarity: shown as active HIGH. Fig 20. GDMA mode timing (bits MODE[1:0] = 10) ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 56 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller RW_N or WR_N 36 ns (min) EOT(1) DREQ th1 004aaa928 (1) Programmable polarity: shown as active LOW. Remark: EOT must be valid for 36 ns (minimum) when RD_N or WR_N is active. Fig 21. EOT timing in generic processor mode 13. Application information address ISP1582 8 A[7:0] data 16 DATA[15:0] CPU read strobe write strobe chip select RD_N WR_N CS_N 004aaa206 Fig 22. Typical interface connections for generic processor mode 14. Test information The dynamic characteristics of the analog I/O ports DP and DM were determined using the circuit shown in Figure 23. test point DUT 15 kΩ CL 50 pF mgt495 In full-speed mode, an internal 1.5 kΩ pull-up resistor is connected to pin DP. Fig 23. Load impedance for pins DP and DM (full-speed mode) ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 57 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller 15. Package outline HVQFN56: plastic thermal enhanced very thin quad flat package; no leads; 56 terminals; body 8 x 8 x 0.85 mm A B D SOT684-1 terminal 1 index area A E A1 c detail X C e1 1/2 e e b 15 L y y1 C v M C A B w M C 28 29 14 e e2 Eh 1/2 e 1 42 terminal 1 index area 56 43 X Dh 0 2.5 scale DIMENSIONS (mm are the original dimensions) UNIT mm A(1) max. A1 b 1 0.05 0.00 0.30 0.18 5 mm c D(1) Dh E(1) Eh 0.2 8.1 7.9 4.45 4.15 8.1 7.9 4.45 4.15 e e1 6.5 0.5 e2 L v w y y1 6.5 0.5 0.3 0.1 0.05 0.05 0.1 Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC JEITA SOT684-1 --- MO-220 --- EUROPEAN PROJECTION ISSUE DATE 01-08-08 02-10-22 Fig 24. Package outline SOT684-1 (HVQFN56) ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 58 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller 16. Soldering of SMD packages This text provides a very brief insight into a complex technology. A more in-depth account of soldering ICs can be found in Application Note AN10365 “Surface mount reflow soldering description”. 16.1 Introduction to soldering Soldering is one of the most common methods through which packages are attached to Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both the mechanical and the electrical connection. There is no single soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high densities that come with increased miniaturization. 16.2 Wave and reflow soldering Wave soldering is a joining technology in which the joints are made by solder coming from a standing wave of liquid solder. The wave soldering process is suitable for the following: • Through-hole components • Leaded or leadless SMDs, which are glued to the surface of the printed circuit board Not all SMDs can be wave soldered. Packages with solder balls, and some leadless packages which have solder lands underneath the body, cannot be wave soldered. Also, leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered, due to an increased probability of bridging. The reflow soldering process involves applying solder paste to a board, followed by component placement and exposure to a temperature profile. Leaded packages, packages with solder balls, and leadless packages are all reflow solderable. Key characteristics in both wave and reflow soldering are: • • • • • • Board specifications, including the board finish, solder masks and vias Package footprints, including solder thieves and orientation The moisture sensitivity level of the packages Package placement Inspection and repair Lead-free soldering versus SnPb soldering 16.3 Wave soldering Key characteristics in wave soldering are: • Process issues, such as application of adhesive and flux, clinching of leads, board transport, the solder wave parameters, and the time during which components are exposed to the wave • Solder bath specifications, including temperature and impurities ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 59 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller 16.4 Reflow soldering Key characteristics in reflow soldering are: • Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see Figure 25) than a SnPb process, thus reducing the process window • Solder paste printing issues including smearing, release, and adjusting the process window for a mix of large and small components on one board • Reflow temperature profile; this profile includes preheat, reflow (in which the board is heated to the peak temperature) and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic). In addition, the peak temperature must be low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table 83 and 84 Table 83. SnPb eutectic process (from J-STD-020C) Package thickness (mm) Package reflow temperature (°C) Volume (mm3) < 350 ≥ 350 < 2.5 235 220 ≥ 2.5 220 220 Table 84. Lead-free process (from J-STD-020C) Package thickness (mm) Package reflow temperature (°C) Volume (mm3) < 350 350 to 2000 > 2000 < 1.6 260 260 260 1.6 to 2.5 260 250 245 > 2.5 250 245 245 Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, see Figure 25. ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 60 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller maximum peak temperature = MSL limit, damage level temperature minimum peak temperature = minimum soldering temperature peak temperature time 001aac844 MSL: Moisture Sensitivity Level Fig 25. Temperature profiles for large and small components For further information on temperature profiles, refer to Application Note AN10365 “Surface mount reflow soldering description”. 17. Abbreviations Table 85. Abbreviations Acronym Description ACK Acknowledgement ACPI Advanced Configuration and Power Interface ASIC Application-Specific Integrated Circuit CRC Cyclic Redundancy Code DMA Direct Memory Access EMI ElectroMagnetic Interference ESR Equivalent Series Resistance FS Full-Speed GDMA Generic DMA HS High-Speed MMU Memory Management Unit NAK Not Acknowledged NRZI Non-Return-to-Zero Inverted NYET Not Yet OTG On-The-Go PCB Printed-Circuit Board PHY Physical PID Packet IDentifier PIE Parallel Interface Engine ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 61 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller Table 85. Abbreviations …continued Acronym Description PIO Parallel Input/Output PLL Phase-Locked Loop POR Power-On Reset RX Receive SE0 Single-Ended zero SIE Serial Interface Engine SRP Session Request Protocol TTL Transistor-Transistor Logic TX Transmit USB Universal Serial Bus 18. References [1] Universal Serial Bus Specification Rev. 2.0 [2] On-The-Go Supplement to the USB Specification Rev. 1.3 [3] Using ISP1582/3 in a composite device application with alternate settings (AN10071) [4] ISP1582/83 and ISP1761 clearing an IN buffer (AN10045) ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 62 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller 19. Revision history Table 86. Revision history Document ID Release date Data sheet status Change notice Supersedes ISP1582_7 20080922 Product data sheet - ISP1582_6 Modifications: • • • • • • • Added Table 3 “Endpoint access and programmability”. • Table 28 “Endpoint Index register: bit allocation”: updated the reset and bus reset values for bit EP0SETUP. • • • • • • • Table 32 “Control Function register: bit description”: updated description for bit CLBUF. Removed Section 7.9 “Clear buffer”. Table 4 “ISP1582 pin status”: updated. Table 5 “ISP1582 output status”: removed two rows. Section 7.15 “Power supply”: updated. Figure 12 “Bus-powered mode”: updated. Table 18 “Mode register: bit allocation”: updated the bus reset value for bits CLKAON and PWRON. Section 8.3.6 “Endpoint MaxPacketSize register (address: 04h)”: updated the first paragraph. Table 42 “Endpoint Type register: bit description”: added a remark to the DBLBUF description. Table 46 “DMA commands”: added a remark to the GDMA stop. Section 12.1 “Register access timing”: updated. Figure 18 “GDMA mode timing (bits MODE[1:0] = 00)”: updated. Section 18 “References”: updated Ref. 3. ISP1582_6 20070920 Product data sheet - ISP1582_5 ISP1582_5 20070201 Product data sheet - ISP1582-04 ISP1582-04 (9397 750 14033) 20050104 Product data 200412038 ISP1582-03 ISP1582-03 (9397 750 13699) 20040825 Preliminary data - ISP1582-02 ISP1582-02 (9397 750 12979) 20040629 Preliminary data - ISP1582-01 ISP1582-01 (9397 750 11496) 20040223 Preliminary data - - ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 63 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller 20. Legal information 20.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 20.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. 20.3 Disclaimers General — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. 20.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. SoftConnect — is a trademark of NXP B.V. 21. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 64 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller 22. Tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Table 17. Table 18. Table 19. Table 20. Table 21. Table 22. Table 23. Table 24. Table 25. Table 26. Table 27. Table 28. Table 29. Table 30. Table 31. Table 32. Table 33. Table 34. Table 35. Table 36. Table 37. Table 38. Table 39. Table 40. Table 41. Table 42. Table 43. Table 44. Table 45. Table 46. Table 47. Table 48. Table 49. Ordering information . . . . . . . . . . . . . . . . . . . . .2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . .4 Endpoint access and programmability . . . . . . . .8 ISP1582 pin status . . . . . . . . . . . . . . . . . . . . . .11 ISP1582 output status . . . . . . . . . . . . . . . . . . .12 Power modes . . . . . . . . . . . . . . . . . . . . . . . . . .17 Operation truth table for SoftConnect . . . . . . .18 Operation truth table for clock off during suspend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Operation truth table for back voltage compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Operation truth table for OTG . . . . . . . . . . . . .19 Operation truth table for SoftConnect . . . . . . .19 Operation truth table for clock off during suspend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Operation truth table for back voltage compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Operation truth table for OTG . . . . . . . . . . . . .20 Register overview . . . . . . . . . . . . . . . . . . . . . .21 Address register: bit allocation . . . . . . . . . . . .23 Address register: bit description . . . . . . . . . . .23 Mode register: bit allocation . . . . . . . . . . . . . . .23 Mode register: bit description . . . . . . . . . . . . .23 Status of the chip . . . . . . . . . . . . . . . . . . . . . . .24 Interrupt Configuration register: bit allocation .25 Interrupt Configuration register: bit description 25 Debug mode settings . . . . . . . . . . . . . . . . . . . .25 OTG register: bit allocation . . . . . . . . . . . . . . .25 OTG register: bit description . . . . . . . . . . . . . .26 Interrupt Enable register: bit allocation . . . . . .28 Interrupt Enable register: bit description . . . . .28 Endpoint Index register: bit allocation . . . . . . .29 Endpoint Index register: bit description . . . . . .30 Addressing of endpoint buffers . . . . . . . . . . . .30 Control Function register: bit allocation . . . . . .30 Control Function register: bit description . . . . .31 Data Port register: bit allocation . . . . . . . . . . .32 Data Port register: bit description . . . . . . . . . .32 Buffer Length register: bit allocation . . . . . . . .33 Buffer Length register: bit description . . . . . . .33 Buffer Status register: bit allocation . . . . . . . . .34 Buffer Status register: bit description . . . . . . . .34 Endpoint MaxPacketSize register: bit allocation . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Endpoint MaxPacketSize register: bit description . . . . . . . . . . . . . . . . . . . . . . . . .35 Endpoint Type register: bit allocation . . . . . . . .35 Endpoint Type register: bit description . . . . . . .36 Control bits for GDMA read/write (opcode = 00h/01h) . . . . . . . . . . . . . . . . . . . . .37 DMA Command register: bit allocation . . . . . .37 DMA Command register: bit description . . . . .37 DMA commands . . . . . . . . . . . . . . . . . . . . . . .38 DMA Transfer Counter register: bit allocation .38 DMA Transfer Counter register: bit description 39 DMA Configuration register: bit allocation . . . .39 Table 50. Table 51. Table 52. Table 53. Table 54. Table 55. Table 56. Table 57. Table 58. Table 59. Table 60. Table 61. Table 62. Table 63. Table 64. Table 65. Table 66. Table 67. Table 68. Table 69. Table 70. Table 71. Table 72. Table 73. Table 74. Table 75. Table 76. Table 77. Table 78. Table 79. Table 80. Table 81. Table 82. Table 83. Table 84. Table 85. Table 86. DMA Configuration register: bit description . . . 40 DMA Hardware register: bit allocation . . . . . . . 40 DMA Hardware register: bit description . . . . . 41 DMA Interrupt Reason register: bit allocation . 41 DMA Interrupt Reason register: bit description 42 Internal EOT-functional relation with bit DMA_XFER_OK . . . . . . . . . . . . . . . . . . . . . . . 42 DMA Interrupt Enable register: bit allocation . . 42 DMA Endpoint register: bit allocation . . . . . . . 43 DMA Endpoint register: bit description . . . . . . 43 DMA Burst Counter register: bit allocation . . . 43 DMA Burst Counter register: bit description . . 44 Interrupt register: bit allocation . . . . . . . . . . . . 44 Interrupt register: bit description . . . . . . . . . . . 45 Chip ID register: bit allocation . . . . . . . . . . . . . 46 Chip ID register: bit description . . . . . . . . . . . . 46 Frame Number register: bit allocation . . . . . . . 46 Frame Number register: bit description . . . . . . 47 Scratch register: bit allocation . . . . . . . . . . . . . 47 Scratch register: bit description . . . . . . . . . . . . 47 Unlock Device register: bit allocation . . . . . . . 47 Unlock Device register: bit description . . . . . . 48 Test Mode register: bit allocation . . . . . . . . . . . 48 Test Mode register: bit description . . . . . . . . . 48 Limiting values . . . . . . . . . . . . . . . . . . . . . . . . . 49 Recommended operating conditions . . . . . . . . 49 Static characteristics: supply pins . . . . . . . . . . 49 Static characteristics: digital pins . . . . . . . . . . 50 Static characteristics: OTG detection . . . . . . . 50 Static characteristics: analog I/O pins DP and DM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Dynamic characteristics . . . . . . . . . . . . . . . . . 51 Dynamic characteristics: analog I/O pins DP and DM . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Register access timing parameters: separate address and data buses . . . . . . . . . . 53 GDMA mode timing parameters . . . . . . . . . . . 55 SnPb eutectic process (from J-STD-020C) . . . 60 Lead-free process (from J-STD-020C) . . . . . . 60 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 63 ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 65 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller 23. Figures Fig 1. Fig 2. Fig 3. Fig 4. Fig 5. Fig 6. Fig 7. Fig 8. Fig 9. Fig 10. Fig 11. Fig 12. Fig 13. Fig 14. Fig 15. Fig 16. Fig 17. Fig 18. Fig 19. Fig 20. Fig 21. Fig 22. Fig 23. Fig 24. Fig 25. Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Pin configuration HVQFN56 (top view) . . . . . . . . .4 Interrupt logic . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Behavior of bit GLINTENA . . . . . . . . . . . . . . . . . .14 Resistor and electrolytic or tantalum capacitor needed for VBUS sensing . . . . . . . . . . . . . . . . . . .15 Oscilloscope reading: no resistor and capacitor in the network . . . . . . . . . . . . . . . . . . . .15 Oscilloscope reading: with resistor and capacitor in the network . . . . . . . . . . . . . . . . . . . .15 POR timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Clock with respect to the external POR . . . . . . . .16 ISP1582 with 3.3 V supply . . . . . . . . . . . . . . . . . .17 Self-powered mode . . . . . . . . . . . . . . . . . . . . . . .18 Bus-powered mode . . . . . . . . . . . . . . . . . . . . . . .19 Source differential data-to-EOP transition skew and EOP width . . . . . . . . . . . . . . . . . . . . . .52 Receiver differential data jitter . . . . . . . . . . . . . . .53 Receiver SE0 width tolerance . . . . . . . . . . . . . . .53 Register access timing: separate address and data buses . . . . . . . . . . . . . . . . . . . . . . . . . .54 ISP1582 ready signal timing . . . . . . . . . . . . . . . .54 GDMA mode timing (bits MODE[1:0] = 00) . . . . .55 GDMA mode timing (bits MODE[1:0] = 01) . . . . .56 GDMA mode timing (bits MODE[1:0] = 10) . . . . .56 EOT timing in generic processor mode . . . . . . . .57 Typical interface connections for generic processor mode . . . . . . . . . . . . . . . . . . . . . . . . . .57 Load impedance for pins DP and DM (full-speed mode) . . . . . . . . . . . . . . . . . . . . . . . . .57 Package outline SOT684-1 (HVQFN56) . . . . . . .58 Temperature profiles for large and small components . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61 ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 66 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller 24. Contents 1 2 3 4 5 6 6.1 6.2 7 7.1 7.2 7.3 7.4 7.5 7.6 7.6.1 7.6.2 7.6.3 7.6.4 7.7 7.8 7.9 7.10 7.11 7.12 7.12.1 7.12.2 7.13 7.14 7.15 7.15.1 7.15.2 8 8.1 8.2 8.2.1 8.2.2 8.2.3 8.2.4 8.2.4.1 8.2.5 8.3 8.3.1 8.3.2 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 4 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4 Functional description . . . . . . . . . . . . . . . . . . . 8 DMA interface, DMA handler and DMA registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Hi-Speed USB transceiver . . . . . . . . . . . . . . . . 9 MMU and integrated RAM . . . . . . . . . . . . . . . . 9 Microcontroller interface and microcontroller handler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 OTG SRP module . . . . . . . . . . . . . . . . . . . . . . . 9 NXP high-speed transceiver . . . . . . . . . . . . . . 10 NXP Parallel Interface Engine (PIE) . . . . . . . . 10 Peripheral circuit . . . . . . . . . . . . . . . . . . . . . . . 10 HS detection . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Isolation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 NXP Serial Interface Engine (SIE) . . . . . . . . . 11 SoftConnect . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Reconfiguring endpoints . . . . . . . . . . . . . . . . . 11 System controller . . . . . . . . . . . . . . . . . . . . . . 11 Pins status . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Interrupt output pin . . . . . . . . . . . . . . . . . . . . . 12 Interrupt control . . . . . . . . . . . . . . . . . . . . . . . 14 VBUS sensing . . . . . . . . . . . . . . . . . . . . . . . . . 14 Power-on reset . . . . . . . . . . . . . . . . . . . . . . . . 15 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . 16 Self-powered mode. . . . . . . . . . . . . . . . . . . . . 18 Bus-powered mode. . . . . . . . . . . . . . . . . . . . . 19 Register description . . . . . . . . . . . . . . . . . . . . 21 Register access . . . . . . . . . . . . . . . . . . . . . . . 22 Initialization registers . . . . . . . . . . . . . . . . . . . 22 Address register (address: 00h) . . . . . . . . . . . 22 Mode register (address: 0Ch) . . . . . . . . . . . . . 23 Interrupt Configuration register (address: 10h) 24 OTG register (address: 12h) . . . . . . . . . . . . . . 25 Session Request Protocol (SRP) . . . . . . . . . . 27 Interrupt Enable register (address: 14h) . . . . . 27 Data flow registers . . . . . . . . . . . . . . . . . . . . . 29 Endpoint Index register (address: 2Ch) . . . . . 29 Control Function register (address: 28h) . . . . 30 8.3.3 8.3.4 8.3.5 8.3.6 8.3.7 8.4 8.4.1 8.4.2 8.4.3 8.4.4 8.4.5 8.4.6 8.4.7 8.4.8 8.5 8.5.1 8.5.2 8.5.3 8.5.4 8.5.5 8.5.6 9 10 11 12 12.1 12.2 13 14 15 16 16.1 16.2 16.3 16.4 17 18 19 20 20.1 20.2 20.3 20.4 21 Data Port register (address: 20h) . . . . . . . . . . Buffer Length register (address: 1Ch) . . . . . . Buffer Status register (address: 1Eh) . . . . . . . Endpoint MaxPacketSize register (address: 04h) . . . . . . . . . . . . . . . . . . . . . . . . Endpoint Type register (address: 08h) . . . . . . DMA registers . . . . . . . . . . . . . . . . . . . . . . . . DMA Command register (address: 30h) . . . . DMA Transfer Counter register (address: 34h) DMA Configuration register (address: 38h) . . DMA Hardware register (address: 3Ch) . . . . . DMA Interrupt Reason register (address: 50h) DMA Interrupt Enable register (address: 54h) DMA Endpoint register (address: 58h). . . . . . DMA Burst Counter register (address: 64h). . General registers . . . . . . . . . . . . . . . . . . . . . . Interrupt register (address: 18h). . . . . . . . . . . Chip ID register (address: 70h) . . . . . . . . . . . Frame Number register (address: 74h) . . . . . Scratch register (address: 78h) . . . . . . . . . . . Unlock Device register (address: 7Ch). . . . . . Test Mode register (address: 84h) . . . . . . . . . Limiting values . . . . . . . . . . . . . . . . . . . . . . . . Recommended operating conditions . . . . . . Static characteristics . . . . . . . . . . . . . . . . . . . Dynamic characteristics . . . . . . . . . . . . . . . . . Register access timing . . . . . . . . . . . . . . . . . . DMA timing. . . . . . . . . . . . . . . . . . . . . . . . . . . Application information . . . . . . . . . . . . . . . . . Test information. . . . . . . . . . . . . . . . . . . . . . . . Package outline . . . . . . . . . . . . . . . . . . . . . . . . Soldering of SMD packages . . . . . . . . . . . . . . Introduction to soldering. . . . . . . . . . . . . . . . . Wave and reflow soldering . . . . . . . . . . . . . . . Wave soldering. . . . . . . . . . . . . . . . . . . . . . . . Reflow soldering. . . . . . . . . . . . . . . . . . . . . . . Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . References . . . . . . . . . . . . . . . . . . . . . . . . . . . . Revision history . . . . . . . . . . . . . . . . . . . . . . . Legal information . . . . . . . . . . . . . . . . . . . . . . Data sheet status . . . . . . . . . . . . . . . . . . . . . . Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . Contact information . . . . . . . . . . . . . . . . . . . . 31 32 33 34 35 36 37 38 39 40 41 42 43 43 44 44 46 46 47 47 48 49 49 49 51 53 55 57 57 58 59 59 59 59 60 61 62 63 64 64 64 64 64 64 continued >> ISP1582_7 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 07 — 22 September 2008 67 of 68 ISP1582 NXP Semiconductors Hi-Speed USB peripheral controller 22 23 24 Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP B.V. 2008. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] Date of release: 22 September 2008 Document identifier: ISP1582_7