INTEGRATED CIRCUITS DATA SHEET 74LVC1GU04 Inverter Product specification Supersedes data of 2004 Jun 28 2004 Sep 21 Philips Semiconductors Product specification Inverter 74LVC1GU04 FEATURES DESCRIPTION • Wide supply voltage range from 1.65 V to 5.5 V The 74LVC1GU04 is a high-performance, low-power, low-voltage, Si-gate CMOS device, superior to most advanced CMOS compatible TTL families. • High noise immunity • ±24 mA output drive (VCC = 3.0 V) The input can be driven from either 3.3 V or 5 V devices. This feature allows the use of this device in a mixed 3.3 V and 5 V environment. • CMOS low power consumption • Latch-up performance exceeds 250 mA • Input accepts voltages up to 5 V Schmitt-trigger action at all inputs makes the circuit tolerant for slower input rise and fall time. • Multiple package options • ESD protection: The 74LVC1GU04 provides the inverting single state unbuffered function. – HBM EIA/JESD22-A114-B exceeds 2000 V – MM EIA/JESD22-A115-A exceeds 200 V. • Specified from −40 °C to +85 °C and −40 °C to +125 °C. QUICK REFERENCE DATA Ground = 0 V; Tamb = 25 °C; tr = tf ≤ 2.5 ns. SYMBOL tPHL/tPLH PARAMETER propagation delay A to Y CI input capacitance CPD power dissipation capacitance CONDITIONS UNIT VCC = 1.8 V; CL = 30 pF; RL = 1 kΩ 1.7 ns VCC = 2.5 V; CL = 30 pF; RL = 500 Ω 1.3 ns VCC = 2.7 V; CL = 50 pF; RL = 500 Ω 1.7 ns VCC = 3.3 V; CL = 50 pF; RL = 500 Ω 1.6 ns VCC = 5.0 V; CL = 50 pF; RL = 500 Ω 1.3 ns 6 pF VCC = 3.3 V; notes 1 and 2 14.9 pF Notes 1. CPD is used to determine the dynamic power dissipation (PD in µW). PD = CPD × VCC2 × fi × N + Σ(CL × VCC2 × fo) where: fi = input frequency in MHz; fo = output frequency in MHz; CL = output load capacitance in pF; VCC = supply voltage in Volts; N = total load switching outputs; Σ(CL × VCC2 × fo) = sum of the outputs. 2. The condition is VI = GND to VCC. 2004 Sep 21 TYPICAL 2 Philips Semiconductors Product specification Inverter 74LVC1GU04 FUNCTION TABLE See note 1. INPUT OUTPUT A Y L H H L Note 1. H = HIGH voltage level; L = LOW voltage level. ORDERING INFORMATION PACKAGE TYPE NUMBER 74LVC1GU04GW TEMPERATURE RANGE PINS PACKAGE MATERIAL CODE MARKING −40 °C to +125 °C 5 SC-88A plastic SOT353 VD 74LVC1GU04GV −40 °C to +125 °C 5 SC-74A plastic SOT753 VU4 74LVC1GU04GM −40 °C to +125 °C 6 XSON6 plastic SOT886 VD PINNING PIN SC-88A; SC-74A PIN XSON6 SYMBOL DESCRIPTION 1 1 n.c. not connected 2 2 A data input A 3 3 GND ground (0 V) 4 4 Y data output Y - 5 n.c. not connected 5 6 VCC supply voltage U04 n.c. 1 A 2 GND 3 5 VCC U04 4 n.c. 1 6 VCC A 2 5 n.c. GND 3 4 Y Y 001aab666 001aab667 Transparent top view Fig.1 Pin configuration SC-88A and SC-77A. 2004 Sep 21 Fig.2 Pin configuration XSON6. 3 Philips Semiconductors Product specification Inverter 74LVC1GU04 handbook, halfpage 2 A Y handbook, halfpage 4 Fig.3 Logic symbol. VCC 4 Fig.4 IEEE logic symbol. VCC 100 Ω Y A MNA636 Fig.5 Logic diagram. 2004 Sep 21 1 MNA109 MNA108 handbook, halfpage 2 4 Philips Semiconductors Product specification Inverter 74LVC1GU04 RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT VCC supply voltage 1.65 5.5 V VI input voltage 0 5.5 V VO output voltage 0 VCC V Tamb operating ambient temperature tr, tf input rise and fall times −40 +125 °C VCC = 1.65 V to 2.7 V 0 20 ns/V VCC = 2.7 V to 5.5 V 0 10 ns/V LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 60134); voltages are referenced to GND (ground = 0 V). SYMBOL PARAMETER CONDITIONS VCC supply voltage IIK input diode current VI < 0 V MIN. MAX. UNIT −0.5 +6.5 V − −50 mA VI input voltage note 1 −0.5 +6.5 V IOK output diode current VO > VCC or VO < 0 V − ±50 mA VO output voltage active mode; note 1 −0.5 VCC + 0.5 V VO = 0 V to VCC IO output source or sink current − ±50 mA ICC, IGND VCC or GND current − ±100 mA Tstg storage temperature −65 +150 °C Ptot power dissipation 200 mW Tamb = −40 °C to +125 °C; note 2 − Notes 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. Above 55 °C the value of Ptot derates linearly with 4.5 mW/K. 2004 Sep 21 5 Philips Semiconductors Product specification Inverter 74LVC1GU04 DC CHARACTERISTICS At recommended operating conditions; voltages are referenced to GND (ground = 0 V). TEST CONDITIONS SYMBOL PARAMETER MIN. OTHER TYP.(1) MAX. UNIT VCC (V) Tamb = −40 °C to +85 °C VIH HIGH-level input voltage 1.65 to 5.5 0.75 × VCC − − VIL LOW-level input voltage 1.65 to 5.5 − − 0.25 × VCC V VOL LOW-level output voltage VI = VIH or VIL IO = 100 µA 1.65 to 5.5 − − 0.1 V IO = 4 mA 1.65 − − 0.45 V IO = 8 mA 2.3 − − 0.3 V IO = 12 mA 2.7 − − 0.4 V IO = 24 mA 3.0 − − 0.55 V IO = 32 mA 4.5 − − 0.55 V IO = −100 µA 1.65 to 5.5 VCC − 0.1 − − V IO = −4 mA 1.65 1.2 − − V IO = −8 mA 2.3 1.9 − − V IO = −12 mA 2.7 2.2 − − V IO = −24 mA 3.0 2.3 − − V IO = −32 mA 4.5 3.8 − − V VOH HIGH-level output voltage V VI = VIH or VIL ILI input leakage current VI = 5.5 V or GND 3.6 − ±0.1 ±5 µA ICC quiescent supply current VI = VCC or GND; IO = 0 A 5.5 − 0.1 10 µA 2004 Sep 21 6 Philips Semiconductors Product specification Inverter 74LVC1GU04 TEST CONDITIONS SYMBOL PARAMETER MIN. OTHER TYP.(1) MAX. UNIT VCC (V) Tamb = −40 °C to +125 °C VIH HIGH-level input voltage 1.65 to 5.5 0.8 × VCC − − V VIL LOW-level input voltage 1.65 to 5.5 − − 0.2 × VCC V VOL LOW-level output voltage VI = VIH or VIL IO = 100 µA 1.65 to 5.5 − − 0.1 V IO = 4 mA 1.65 − − 0.70 V IO = 8 mA 2.3 − − 0.45 V IO = 12 mA 2.7 − − 0.60 V IO = 24 mA 3.0 − − 0.80 V IO = 32 mA 4.5 − − 0.80 V IO = −100 µA 1.65 to 5.5 VCC − 0.1 − − V IO = −4 mA 1.65 0.95 − − V IO = −8 mA 2.3 1.7 − − V IO = −12 mA 2.7 1.9 − − V IO = −24 mA 3.0 2.0 − − V VOH HIGH-level output voltage VI = VIH or VIL IO = −32 mA 4.5 3.4 − − V ILI input leakage current VI = 5.5 V or GND 3.6 − ±0.1 ±5 µA ICC quiescent supply current VI = VCC or GND; IO = 0 A 5.5 − − 200 µA Note 1. All typical values are measured at VCC = 3.3 V and Tamb = 25 °C. 2004 Sep 21 7 Philips Semiconductors Product specification Inverter 74LVC1GU04 AC CHARACTERISTICS GND = 0 V; tr = tf ≤ 2.0 ns. TEST CONDITIONS SYMBOL PARAMETER TYP.(1) MIN. WAVEFORMS MAX. UNIT VCC (V) Tamb = −40 °C to +85 °C tPHL/tPLH propagation delay A to Y see Figs 6 and 9 1.65 to 1.95 0.3 1.7 5.0 ns 2.3 to 2.7 0.3 1.3 4.0 ns 2.7 0.5 1.7 5.0 ns 3.0 to 3.6 0.5 1.6 3.7 ns 4.5 to 5.5 0.5 1.3 3.0 ns 1.65 to 1.95 0.3 − 6.5 ns 2.3 to 2.7 0.3 − 5.5 ns 2.7 0.5 − 6.5 ns 3.0 to 3.6 0.5 − 5.0 ns 4.5 to 5.5 0.5 − 4.0 ns Tamb = −40 °C to +125 °C tPHL/tPLH propagation delay A to Y see Figs 6 and 9 Note 1. All typical values are measured at Tamb = 25 °C. AC WAVEFORMS VI handbook, halfpage VM A input GND t PHL t PLH VOH VM Y output VOL MNA637 INPUT VCC VM VI tr = tf 0.5 × VCC VCC 2.3 V to 2.7 V 0.5 × VCC VCC ≤ 2.0 ns 2.7 V 1.5 V 2.7 V ≤ 2.5 ns 3.0 V to 3.6 V 1.5 V 2.7 V ≤ 2.5 ns 4.5 V to 5.5 V 0.5 × VCC VCC ≤ 2.5 ns 1.65 V to 1.95 V ≤ 2.0 ns VOL and VOH are typical output voltage drop that occur with the output load. Fig.6 Input A to output Y propagation delay times. 2004 Sep 21 8 Philips Semiconductors Product specification Inverter 74LVC1GU04 MNA639 120 fs (mA/V) 100 handbook, halfpage G Rbias = 560 kΩ handbook, halfpage VCC 80 0.47 µF input output 100 µF 60 Vi A Io 40 MNA638 20 0 ∆I G fs = --------o∆V i 0 2 fi = 1 kHz. VO is constant. Tamb = 25 °C. Fig.7 Fig.8 Test set-up for measuring forward transconductance. VEXT VCC VI RL VO D.U.T. CL RT RL MNA616 VCC VI CL RL VEXT tPLH/tPHL tPZH/tPHZ tPZL/tPLZ 1.65 V to 1.95 V VCC 30 pF 1 kΩ open GND 2 × VCC 2.3 V to 2.7 V VCC 30 pF 500 Ω open GND 2 × VCC 2.7 V 2.7 V 50 pF 500 Ω open GND 6V 3.0 V to 3.6 V 2.7 V 50 pF 500 Ω open GND 6V 4.5 V to 5.5 V VCC 50 pF 500 Ω open GND 2 × VCC Definitions for test circuit: RL = Load resistor. CL = Load capacitance including jig and probe capacitance. RT = Termination resistance should be equal to the output impedance Zo of the pulse generator. Fig.9 Load circuitry for switching times. 2004 Sep 21 9 VCC (V) 6 Typical forward transconductance as a function of supply voltage. handbook, full pagewidth PULSE GENERATOR 4 Philips Semiconductors Product specification Inverter 74LVC1GU04 APPLICATION INFORMATION Remark to the application information Some applications for the 74LVC1GU04 are: All values given are typical values unless otherwise specified. • Linear amplifier (see Fig.10) • Crystal oscillator (see Fig.11). R2 handbook, halfpage handbook, halfpage R1 VCC 1 µF R1 R2 U04 U04 ZL C1 C2 out MNA052 MNA053 ZL > 10 kΩ, R1 ≥ 3 kΩ and R2 ≤ 1 MΩ. Open loop amplification: AOL = 20 (typical value). C1 = 47 pF (typical). C2 = 22 pF (typical). R1 = 1 to 10 MΩ (typical). R2 optimum value depends on the frequency and required stability against changes in VCC or average minimum ICC [ICC = 2 mA (typical) at VCC = 3.3 V and f = 10 MHz]. A OL Voltage amplification: A u = – ------------------------------------------R1 1 + -------- ( 1 + A OL ) R2 Maximum output voltage: V o(p-p) ≈ V CC – 1.5 V centered at 0.5V CC Unity gain bandwidth product: B = 5 MHz (typical value). Fig.10 Used as a linear amplifier. 2004 Sep 21 Fig.11 Crystal oscillator configuration. 10 Philips Semiconductors Product specification Inverter 74LVC1GU04 PACKAGE OUTLINES Plastic surface mounted package; 5 leads SOT353 D E B y X A HE 5 v M A 4 Q A A1 1 2 e1 3 bp c Lp w M B e detail X 0 1 2 mm scale DIMENSIONS (mm are the original dimensions) UNIT A A1 max bp c D E (2) e e1 HE Lp Q v w y mm 1.1 0.8 0.1 0.30 0.20 0.25 0.10 2.2 1.8 1.35 1.15 1.3 0.65 2.2 2.0 0.45 0.15 0.25 0.15 0.2 0.2 0.1 OUTLINE VERSION SOT353 2004 Sep 21 REFERENCES IEC JEDEC EIAJ SC-88A 11 EUROPEAN PROJECTION ISSUE DATE 97-02-28 Philips Semiconductors Product specification Inverter 74LVC1GU04 Plastic surface mounted package; 5 leads SOT753 D E B y A X HE 5 v M A 4 Q A A1 c 1 2 3 Lp detail X bp e w M B 0 1 2 mm scale DIMENSIONS (mm are the original dimensions) UNIT A A1 bp c D E e HE Lp Q v w y mm 1.1 0.9 0.100 0.013 0.40 0.25 0.26 0.10 3.1 2.7 1.7 1.3 0.95 3.0 2.5 0.6 0.2 0.33 0.23 0.2 0.2 0.1 OUTLINE VERSION SOT753 2004 Sep 21 REFERENCES IEC JEDEC JEITA SC-74A 12 EUROPEAN PROJECTION ISSUE DATE 02-04-16 Philips Semiconductors Product specification Inverter 74LVC1GU04 XSON6: plastic extremely thin small outline package; no leads; 6 terminals; body 1 x 1.45 x 0.5 mm SOT886 b 1 2 3 4× (2) L L1 e 6 5 e1 4 e1 6× A (2) A1 D E terminal 1 index area 0 1 2 mm scale DIMENSIONS (mm are the original dimensions) UNIT A (1) max A1 max b D E e e1 L L1 mm 0.5 0.04 0.25 0.17 1.5 1.4 1.05 0.95 0.6 0.5 0.35 0.27 0.40 0.32 Notes 1. Including plating thickness. 2. Can be visible in some manufacturing processes. OUTLINE VERSION SOT886 2004 Sep 21 REFERENCES IEC JEDEC JEITA EUROPEAN PROJECTION ISSUE DATE 04-07-15 04-07-22 MO-252 13 Philips Semiconductors Product specification Inverter 74LVC1GU04 DATA SHEET STATUS LEVEL DATA SHEET STATUS(1) PRODUCT STATUS(2)(3) Development DEFINITION I Objective data II Preliminary data Qualification This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. III Product data This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Production This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. Notes 1. Please consult the most recently issued data sheet before initiating or completing a design. 2. The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. 3. For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status. DEFINITIONS DISCLAIMERS Short-form specification The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Life support applications These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Limiting values definition Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Right to make changes Philips Semiconductors reserves the right to make changes in the products including circuits, standard cells, and/or software described or contained herein in order to improve design and/or performance. When the product is in full production (status ‘Production’), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no licence or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Application information Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. 2004 Sep 21 14 Philips Semiconductors – a worldwide company Contact information For additional information please visit http://www.semiconductors.philips.com. Fax: +31 40 27 24825 For sales offices addresses send e-mail to: [email protected]. SCA76 © Koninklijke Philips Electronics N.V. 2004 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Printed in The Netherlands R20/06/pp15 Date of release: 2004 Sep 21 Document order number: 9397 750 13769