INTEGRATED CIRCUITS 74ALS153 Dual 4-input multiplexer Product specification IC05 Data Handbook 1991 Feb 08 Philips Semiconductors Product specification Dual 4-input multiplexer 74ALS153 FEATURES PIN CONFIGURATION • Non–inverting outputs • Common select outputs • Separate enable for each section • See 74ALS253 for 3–State version Ea 1 16 VCC S1 2 15 Eb I3a 3 14 S0 I2a 4 13 I3b DESCRIPTION I1a 5 12 I2b The 74ALS153 has two identical 4–input multiplexer with 3–State outputs which selects two bits of data from four sources by using common select inputs (S0, S1). The two 4–input multiplexer circuits have individual active–Low enables (Ea, Eb) which can be used to strobe the outputs independently. Outputs (Ya, Yb) are forced Low when the corresponding enable is high. I0a 6 11 I1b Ya 7 10 I0b GND 8 9 Yb SF00146 The 74ALS153 is the logic implementation of a 2–pole, 4–position switch where the position of the switch is determined by the logic levels supplied to the common select inputs. TYPE ORDERING INFORMATION ORDER CODE DESCRIPTION COMMERCIAL RANGE VCC = 5V ±10%, Tamb = 0°C to +70°C DRAWING NUMBER TYPICAL PROPAGATION DELAY TYPICAL SUPPLY CURRENT (TOTAL) 16-pin plastic DIP 74ALS153N SOT38-4 7.0ns 6.5mA 16-pin plastic SO 74ALS153D SOT109-1 16-pin plastic SSOP Type II 74ALS153DB SOT338-1 74ALS153 INPUT AND OUTPUT LOADING AND FAN-OUT TABLE PINS DESCRIPTION 74ALS (U.L.) HIGH/LOW LOAD VALUE HIGH/LOW Ioa – I3a Port A data inputs 1.0/1.0 20µA/0.1mA Iob – I3b Port B data inputs 1.0/1.0 20µA/0.1mA Common select inputs 1.0/1.0 20µA/0.1mA Ea Port A enable input 1.0/1.0 20µA/0.1mA Eb Port B enable input 1.0/1.0 20µA/0.1mA Data outputs 130/240 2.6mA/24mA S0, S1 Ya, Yb NOTE: One (1.0) ALS unit load is defined as: 20µA in the High state and 0.1mA in the Low state. LOGIC SYMBOL IEC/IEEE SYMBOL 6 5 4 3 10 11 12 14 13 2 I0a I1a I2a I3a I0b I1b I2b I3b 1 14 S0 6 2 S1 5 1 Ea 15 Eb 4 3 Ya 0 G 1 EN 0 1 0 3 MUX 7 2 3 15 Yb 10 11 9 12 7 9 13 VCC = Pin 16 GND = Pin 8 SF00148 SF00147 1991 Feb 08 2 853–1376 01670 Philips Semiconductors Product specification Dual 4-input multiplexer 74ALS153 LOGIC DIAGRAM Ea 1 I0a 6 I1a 5 I2a 4 I3a 3 S1 S2 2 I0b 14 10 I0b I2b I3b 11 12 13 7 VCC = Pin 16 GND = Pin 8 Eb 15 9 Ya Yb SF00149A FUNCTION TABLE INPUTS OUTPUT S0 S1 I0n I1n I2n I3n En Yn L L L X X X L L L L H X X X L H H L X L X X L L H L X H X X L H L H X X L X L L L H X X H X L H H H X X X L L L H H X X X H L H H = High voltage level L = Low voltage level X = Don’t care 1991 Feb 08 3 Philips Semiconductors Product specification Dual 4-input multiplexer 74ALS153 ABSOLUTE MAXIMUM RATINGS (Operation beyond the limit set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free-air temperature range.) PARAMETER SYMBOL RATING UNIT VCC Supply voltage –0.5 to +7.0 V VIN Input voltage –0.5 to +7.0 V IIN Input current –30 to +5 mA –0.5 to VCC V VOUT Voltage applied to output in high output state IOUT Current applied to output in Low output state Tamb Operating free-air temperature range Tstg Storage temperature range 48 mA 0 to +70 °C –65 to +150 °C RECOMMENDED OPERATING CONDITIONS LIMITS SYMBOL PARAMETER UNIT MIN NOM MAX 5.0 5.5 VCC Supply voltage 4.5 VIH High-level input voltage 2.0 VIL Low-level input voltage 0.8 V IIk Input clamp current –18 mA IOH High-level output current –2.6 mA IOL Low-level output current 24 mA +70 °C Tamb Operating free-air temperature range V V 0 DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) SYMBOL PARAMETER LIMITS TEST CONDITIONS1 MIN VCC = ±10%,, VIL = MAX,, VIH = MIN IOH = –0.4mA VCC – 2 IOH = MAX 2.4 TYP2 UNIT MAX V VOH O High level output voltage High-level VOL O Low level output voltage Low-level VIK Input clamp voltage VCC = MIN, II = IIK II Input current at minimum input voltage VCC = MAX, VI = 7.0V IIH High-level input current VCC = MAX, VI = 2.7V 20 µA IIL Low-level input current VCC = MAX, VI = 0.4V –0.1 mA IO Output current3 VCC = MAX, VO = 2.25V –112 mA ICC Supply current (total) VCC = MAX 12 mA VCC = MIN,, VIL = MAX,, VIH = MIN 3.2 V IOL = 12mA 0.25 0.40 V IOL = 24mA 0.35 0.50 V –0.73 –1.5 V 0.1 mA –30 6.5 NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25°C. 3. The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, IOS. 1991 Feb 08 4 Philips Semiconductors Product specification Dual 4-input multiplexer 74ALS153 AC ELECTRICAL CHARACTERISTICS LIMITS SYMBOL PARAMETER Tamb = 0°C to +70°C VCC = +5.0V ± 10% CL = 50pF, RL = 500Ω TEST CONDITION MIN MAX UNIT tPLH tPHL Propagation delay In to Yn Waveform 1 4.0 4.0 12.0 12.0 ns tPLH tPHL Propagation delay Sn to Yn Waveform 2 5.0 7.0 15.0 16.0 ns tPLH tPHL Propagation delay En to Yn Waveform 2 3.0 5.0 10.0 12.0 ns AC WAVEFORMS For all waveforms, VM = 1.3V. In Sn VM VM VM tPLH tPHL VM Yn VM En tPLH VM tPHL VM Yn VM SF00150 Waveform 1. Propagation Delay for Data to Output SC00046 Waveform 2. Propagation Delay for Select or Enable to Output TEST CIRCUIT AND WAVEFORMS VCC VIN CL RL AMP (V) VM 10% D.U.T. RT 90% VM VOUT PULSE GENERATOR tw 90% NEGATIVE PULSE 10% tTHL (tff) tTLH (tr ) tTLH (tr ) tTHL (tf ) 0.3V AMP (V) 90% Test Circuit for Totem-pole Outputs POSITIVE PULSE 90% VM VM 10% 10% tw 0.3V Input Pulse Definition DEFINITIONS: RL = Load resistor; see AC electrical characteristics for value. CL = Load capacitance includes jig and probe capacitance; see AC electrical characteristics for value. RT = Termination resistance should be equal to ZOUT of pulse generators. INPUT PULSE REQUIREMENTS Family Amplitude VM 74ALS 3.5V 1.3V Rep.Rate tw tTLH tTHL 1MHz 500ns 2.0ns 2.0ns SC00005 1991 Feb 08 5 Philips Semiconductors Product specification Dual 4-input multiplexer 74ALS153 DIP16: plastic dual in-line package; 16 leads (300 mil) 1991 Feb 08 6 SOT38-4 Philips Semiconductors Product specification Dual 4-input multiplexer 74ALS153 SO16: plastic small outline package; 16 leads; body width 3.9 mm 1991 Feb 08 7 SOT109-1 Philips Semiconductors Product specification Dual 4-input multiplexer 74ALS153 SSOP16: plastic shrink small outline package; 16 leads; body width 5.3 mm 1991 Feb 08 8 SOT338-1 Philips Semiconductors Product specification Dual 4-input multiplexer 74ALS153 DEFINITIONS Data Sheet Identification Product Status Definition Objective Specification Formative or in Design This data sheet contains the design target or goal specifications for product development. Specifications may change in any manner without notice. Preliminary Specification Preproduction Product This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Product Specification Full Production This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes at any time without notice, in order to improve design and supply the best possible product. Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. LIFE SUPPORT APPLICATIONS Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices, or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale. Copyright Philips Electronics North America Corporation 1997 All rights reserved. Printed in U.S.A. Philips Semiconductors 811 East Arques Avenue P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381 1991 Feb 08 9