KEMET Organic Capacitor (KO-CAP) T521 High Voltage Polymer Tantalum Overview The KEMET Organic Capacitor (KO-CAP) is a tantalum capacitor with a Ta anode and Ta2O5 dielectric. A conductive organic polymer replaces the traditionally used MnO2 as the cathode plate of the capacitor. This results in very low ESR and improved capacitance retention at high frequency. The KO-CAP also exhibits a benign failure mode which eliminates the ignition failures that can occur in standard MnO2 tantalum types. KOCAPs may also be operated at steady state voltages up to 90% of rated voltage for part types with rated voltages of ≤10 volts and up to 80% of rated voltage for part types >10 volts with equivalent or better reliability than traditional MnO2 tantalum capacitors operated at 50% of rated voltage. The T521 Series High Voltage Polymer Tantalum is designed Benefits • • • • • • • • • • • for higher application voltages such as 12V, 24V and 28V input rails. This series demonstrates excellent high voltage handling capabilities and reliability and is commonly selected as a replacement for other high capacitance dielectrics such as MnO2 tantalum and aluminum electrolytic capacitors. The T521 Series can be safely operated at 80% of the rated voltage and can withstand transient conditions up to the rated voltage of the component. This series offers higher capacitance for a given application voltage when compared to multilayer ceramic and tantalum MnO2 devices. The T521 Series also offers superior ESR performance over tantalum MnO2 and aluminum electrolytic capacitors and a much lower profile than aluminum polymer and aluminum electrolytic capacitors. Applications Voltage ratings to 35V Volumetric efficiency Stable temperature characteristics Up to 68μF capacitance value High ripple current capability Low ESR High reliability Low profile design Benign failure mode Pb Free when ordered with 100% Sn termination RoHS compliant and Halogen Free Typical applications include DC/DC converters, power supply input and higher voltage applications such as 12V to 28V power input rails in the military/aerospace and industrial markets. Environmental Compliance RoHS Compliant (6/6)* according to Directive 2002/95/EC *When ordered with 100% Sn Solder SPICE For a detailed analysis of specific part numbers, please visit kemet.com for a free download of KEMET's SPICE software. The KEMET SPICE program is freeware intended to aid design engineers in analyzing the performance of these capacitors over frequency, temperature, ripple, and DC bias conditions. One WORLD One Brand One Strategy One Focus One Team © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com One KEMET T2016-1 • 1/17/2011 1 KEMET Organic Capacitor (KO-CAP) – T521 High Voltage Polymer Tantalum Ordering Information T 521 V 226 M 025 A T E060 Capacitor Class Series Case Size Capacitance Code (pF) Capacitance Tolerance Voltage Failure Rate/ Design Lead Material ESR Code 521 = High Voltage Polymer D = 7343-31 V = 7343-20 W = 7343-15 X = 7343-43 First two digits represent significant figures. Third digit specifies number of zeros. M = ±20% T = 100% Matte Tin (Sn) Plated H = Tin/Lead (SnPb) Solder Coated (5% Pb minimum) E = ESR Last three digits specify ESR in mOhms. (060 = 60mOhms) T= Tantalum 016 = 16V 020 = 20V 025 = 25V 035 = 35V A = N/A Packaging (C-Spec) Blank = 7" Reel 7280 = 13" Reel Performance Characteristics Item Performance Characteristics Operating Temperature Rated Capacitance Range Capacitance Tolerance Rated Voltage Range DF(120Hz) ESR (100kHz) Leakage Current -55°C to 105°C/125°C - Refer to Part Number for Max Temp Rating 15µF - 68µF @ 120 Hz/25°C M Tolerance (20%) 16V - 35V ≤ 10% Refer to Part Number Electrical Specification Table ≤ 0.1CV (µA) at Rated Voltage after 5 minutes © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2016-1 • 1/17/2011 2 KEMET Organic Capacitor (KO-CAP) – T521 High Voltage Polymer Tantalum Qualification Test Condition Characteristics ΔC/C Endurance Storage Humidity Temperature Stability 105°C @ Rated Voltage, 2000 Hrs. 125°C @ 2/3 Rated Voltage, 2000 Hrs.** 105°C @ 0 Volts, 2000 Hrs. 125°C @ 0 Voltage, 2000 Hrs.** 60° C, 90% RH, 500Hr, Rated Voltage 60° C, 90% RH, 500Hr, No Load Extreme temperature exposure at a succession of continuous steps at +25 C, -55C, +25 C, +85 C, +105/125 C, +25 C. DF Within initial limits DCL IL @ 105° C, 2x IL @ 125° C ESR 2x Initial Limit ΔC/C Within -20/+10% of initial value DF Within initial limits DCL IL @ 105° C, 2x IL @ 125° C ESR 2x Initial Limit ΔC/C Within -5%/+35% of initial value DF Within initial limits DCL Within 3.0 x initial limit +25°C -55°C +85°C +105/125°C ΔC/C IL* ±20% ±20% ±30% DF IL IL 1.2 x IL 1.5 x IL DCL IL n/a 10 x IL 10 x IL ΔC/C Surge Voltage Mechanical Shock/Vibration Within -20/+10% of initial value 105° C, 1.32 x Rated Voltage, 33Ω Resistance, 1000 cycles Mil-Std-202, Meth. 213, Cond. I, 100G Peak Mil-Std-202, Meth. 204, Cond. D, 10Hz to 2000Hz, 20G Peak Within -20/+10% of initial value DF Within initial limits DCL Within initial limits ESR Within initial limits ΔC/C Within ±10% of initial value DF Within initial limits DCL Within initial limits *IL = Initial Limit **Refer to part number specifications for individual temperature classification. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2016-1 • 1/17/2011 3 KEMET Organic Capacitor (KO-CAP) – T521 High Voltage Polymer Tantalum Electrical Characteristics Capacitance vs. Frequency ESR vs. Frequency 100 100 T521V476M020ATE055_Imp T521V336M025ATE060_Imp T521V156M035ATE100_Imp T521V476M020ATE055_ESR T521V336M025ATE060_ESR T521V156M035ATE100_ESR 1 10 Capacitance (µF) Impedance, ESR (Ohms) 10 0.1 0.01 100 1,000 10,000 100,000 Frequency (Hz) 1,000,000 1 T521V476M020ATE055 T521V336M025ATE060 T521V156M035ATE100 0 10,000,000 100 1,000 10,000 100,000 Frequency (Hz) 1,000,000 10,000,000 Dimensions – Millimeters (Inches) Metric will govern Termination cutout at KEMET’s Option, either end Case Size KEMET EIA D 7343-31 V 7343-20 W 7343-15 X 7343-43 Component L* 7.3 ± 0.3 (287 ± .012) 7.3 ± 0.3 (287 ± .012) 7.3 ± 0.3 (287 ± .012) 7.3 ± 0.3 (.287 ± .012) W* H* 4.3 ± 0.3 2.8 ± 0.3 (.169 ± .012) (098 ± .012) 4.3 ± 0.3 1.9 (.075) max (.169 ± .012) 4.3 ± 0.3 1.5 (.059) max (.169 ± .012) 4.3 ± 0.3 4.0 ± 0.3 (.169 ± .012) (.157 ± .012) F* ±0.1 S* ±0.3 B* ±0.15 ±(.004) ±(.012) (Ref) ±.006 X (Ref) P (Ref) R (Ref) T (Ref) A (Min) G (Ref) E (Ref) 2.4 (.094) 1.3 (.051) 0.5 (.020) 0.10 ± 0.10 (.004 ± .004) 0.9 (.035) 1.0 (.039) 0.13 (.005) 3.8 (.150) 3.5 (.138) 3.5 (.138) 2.4 (.094) 1.3 (.051) n/a 0.05 (.002) n/a n/a 0.13 (.005) 3.8 (.150) 3.5 (.138) 3.5 (.138) 2.4 (.094) 1.3 (.051) n/a 0.05 (.002) n/a n/a 0.13 (.005) 3.8 (.150) 3.5 (.138) 3.5 (.138) 0.5 (.020) 0.10 ± 0.10 (.004 ± .004) 1.7 (.067) 1.0 (.039) 0.13 (.005) 3.8 (.150) 3.5 (.138) 3.5 (.138) 2.4 (.094) 1.3 (.051) Notes: (Ref) – Dimensions provided for reference only. No dimensions provided for B, P or R because low profile cases do not have a bevel or a notch. * MIL-C-55365/8 specified dimensions © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2016-1 • 1/17/2011 4 KEMET Organic Capacitor (KO-CAP) – T521 High Voltage Polymer Tantalum Table 1 – Ratings & Part Number Reference Rated Voltage Rated Cap Case Code/ Case Size KEMET Part Number DC Leakage V/7343-20 V/7343-20 D/7343-31 (See below for part options) T521V686M016A(1)E050 T521V686M016A(1)E090 T521D107M016A(1)E050 +20ºC µAmps 108.8 108.8 160.0 DF ESR Maximum Allowable Ripple Current Moisture Sensitivity +45ºC 100kHz mAmps 1900.0 1400.0 2100.0 Temp≤260ºC J-STD-020D 3 3 3 16 16 16 120Hz µF 68 68 100 20 20 20 47 47 47 V/7343-20 V/7343-20 D/7343-31 T521V476M020A(1)E090 T521V476M020A(1)E055 T521D476M020A(1)E055 94.0 94.0 94.0 10 10 10 90 55 55 1400.0 1800.0 2000.0 3 3 3 125 125 125 25 25 25 22 33 33 V/7343-20 V/7343-20 D/7343-31 T521V226M025A(1)E060 T521V336M025A(1)E060 T521D336M025A(1)E060 55.0 82.5 82.5 10 10 10 60 60 60 1800.0 1800.0 1900.0 3 3 3 105 105 105 35 35 35 35 15 15 47 47 µF 120Hz V/7343-20 V/7343-20 X/7343-43 X/7343-43 52.5 52.5 164.5 164.5 µAmps +20ºC 1400.0 1200.0 2900.0 1900.0 mAmps +45ºC 100kHz 3 3 3 3 J-STD-020d Temp≤260ºC 125 125 125 125 KEMET/EIA T521V156M035A(1)E100 T521V156M035A(1)E125 T521X476M035A(1)E030 T521X476M035A(1)E070 (see below for part options) Case Code/ Case Size KEMET Part Number DC Leakage Maximum allowable ripple current Moisture Sensitivity VDC VDC Rated Voltage Rated Cap KEMET/EIA +20ºC 120Hz +20ºC 100kHz % Max mOhms 10 50 10 90 10 50 Rated Temp 10 100 10 125 10 30 10 70 % Max mOhms +20ºC 120Hz +20ºC 100kHz DF ESR T 521 V 226 M 025 A T E060 Capacitor Class Series Case Size Capacitance Code (pF) Capacitance Tolerance Voltage Failure Rate/ Design Lead Material ESR Code T= Tantalum 521 = High Voltage Polymer Other part number options: D = 7343-31 V = 7343-20 W = 7343-15 X = 7343-43 First two digits M = ±20% 016 = 16V A = N/A T = 100% Matte represent 020 = 20V Tin (Sn) Plated significant 025 = 25V H = Tin/Lead figures. Third 035 = 35V (SnPb) Solder specifi es terminations is also available (14th character Coated 1- Standard with tin terminations (14th characterdigit = T). Tin/lead = H) (5% Pb number of zeros. minimum) E = ESR Last three digits specify ESR in mOhms. (060 = 60mOhms) (ºC) 105 105 105 (ºC) Rated Temp Packaging (C-Spec) Blank = 7" Reel 7280 = 13" Reel Also available on large (13 inch) reels. Add 7280 to the end of the part number. Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitutions will be marked with the higher voltage rating. Substitutions can include better than series. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com Roll Over for Order Info. T2016-1 • 1/17/2011 5 KEMET Organic Capacitor (KO-CAP) – T521 High Voltage Polymer Tantalum Derating Guidelines Max Recommended Max Recommended Steady State Voltage Transient Voltage (1ms - 1µs) -55°C to 105°C 16V ≤ Vr ≤ 35V 80% of Vr Vr 105°C to 125°C 16V ≤ Vr ≤ 35V 54% of Vr 67% of Vr Vr = Rated Voltage 100% 95% 90% 85% 80% 75% 70% 65% 60% 55% 50% -55 % Rated Voltage Voltage Rating Maximum Transient Voltage Recommended Application Voltage 25 45 85 Temperature (°C) 105 125 Ripple Current/Ripple Voltage Permissible AC ripple voltage and current are related to equivalent series resistance (ESR) and the power dissipation capabilities of the device. Permissible AC ripple voltage which may be applied is limited by two criteria: a. The positive peak AC voltage plus the DC bias voltage, if any, must not exceed the DC voltage rating of the capacitor. b. The negative peak AC voltage, in combination with bias voltage, if any, must not exceed the allowable limits specified for reverse voltage. The maximum power dissipation by case size can be determined using the below table. The maximum power dissipation rating stated in the table above must be reduced with increasing environmental operating temperatures. Refer to the below table for temperature compensation requirements. Case Code KEMET T520/525T T520M T520A T520/525B T520U T520L T520C T520W T520V T520/525D T520Y T520X T528Z T530D T530Y T530X EIA 3528-12 3528-15 3216-18 3538-21 6032-15 3528-19 6032-28 7343-15 7343-20 7343-31 7343-40 7343-43 7343-17 7343-31 7343-40 7443-43 Maximum Power Dissipation (Pmax) mWatts @ 45°C w/+30°C Rise 105 120 112 127 135 150 165 180 187 225 241 247 325 255 263 270 ≤45°C 1.00 Temperature Compenstion Multipliers for Maximum Power Dissipation 45°C < T ≤ 85°C 0.70 85°C < T ≤ 105°C 0.25 T= Environmental Temperature Using the P max of the device, the maximum allowable rms ripple current or voltage may be determined. I(max) = √P max/R E(max) = √P max*R I = rms ripple current (amperes) E = rms ripple voltage (volts) Pmax = maximum power dissipation(watts) R = ESR at specified frequency (ohms) © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2016-1 • 1/17/2011 6 KEMET Organic Capacitor (KO-CAP) – T521 High Voltage Polymer Tantalum Reverse Voltage Polymer tantalum capacitors are polar devices and may be permanently damaged or destroyed if connected in the wrong polarity. These devices will withstand a small degree of transient voltage reversal for short periods as shown in the below table. Temperature Permissible Transient Reverse Voltage 25°C 55°C 85°C 105°C 125°C* 15% of Rated Voltage 10% of Rated Voltage 5% of Rated Voltage 3% of Rated Voltage 1% of Rated Voltage *For Series Rated to 125°C Table 2 – Land Dimensions/Courtyard KEMET Metric Size Code Density Level A: Maximum (Most) Land Protrusion (mm) Density Level B: Median (Nominal) Land Protrusion (mm) Density Level C: Minimum (Least) Land Protrusion (mm) Case EIA X Y C V1 V2 X Y C V1 V2 X Y C V1 V2 D 7343-31 2.55 3.75 2.70 10.20 5.50 2.45 3.35 2.60 9.10 5.00 2.35 2.95 2.50 8.20 4.70 V 7343-20 2.55 3.75 2.70 10.20 5.50 2.45 3.35 2.60 9.10 5.00 2.35 2.95 2.50 8.20 4.70 X¹ 7343-43 2.55 3.75 2.70 10.20 5.50 2.45 3.35 2.60 9.10 5.00 2.35 2.95 2.50 8.20 4.70 W 7343-15 2.55 3.75 2.70 10.20 5.50 2.45 3.35 2.60 9.10 5.00 2.35 2.95 2.50 8.20 4.70 Density Level A: For low-density product applications. Recommended for wave solder applications and provides a wider process window for reflow solder processes. Density Level B: For products with a moderate level of component density. Provides a robust solder attachment condition for reflow solder processes. Density Level C: For high component desity product applications. Before adapting the minimum land pattern variations the user should perform qualification testing based on the conditions outlined in IPC standard 7351 (IPC-7351). ¹ Height of these chips may create problems in wave soldering. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2016-1 • 1/17/2011 7 KEMET Organic Capacitor (KO-CAP) – T521 High Voltage Polymer Tantalum Soldering Process T tP Max Ramp Up Rate = 3° C/sec Max Ramp Down Rate = 6° C/sec tL Temperature P KEMET’s families of surface mount tantalum capacitors are compatible with wave (single or dual), convection, IR or vapor TL phase reflow techniques. Preheating of these components is recommended to avoid extreme thermal stress. KEMET's Tsmax recommended profile conditions for convection and IR reflow reflect Tsmin the profile conditions of the IPC/J-STD-020D standard for moisture sensitivety testing. The devices can safely withstand a maximum of three reflow passes at these conditions. 25 Note that although the X/7343-43 case size can withstand wave soldering, the tall profile (4.3mm maximum) dictates care in wave process development. Profile Feature Sn-Pb Assembly Pb-Free Assembly tS 25° C to Peak Time Time/Temperature Soldering Profile Preheat/Soak Temperature Min (TSmin) 100°C 150°C Temperature Max (TSmax) 150°C 200°C Time (ts) from Tsmin to Tsmax) 60-120 sec 60-120 sec Ramp-up rate (TL to TP) 3°C/sec max 3°C/sec max Liquidous temperature (TL) 183°C 217°C Time above liquidous (tL) 60-150 sec 220°C* 235°C** 60-150 sec 250°C* 260°C** 20 sec max 30 sec max Peak Temperature (TP) Time within 5°C of max peak temperature (tP) Ramp-down rate (TP to TL) 6°C/sec max 6°C/sec max Time 25°C to peak temperature 6 minutes max 8 minutes max Note 1: All temperatures refer to the center of the package, measured on the package body surface that is facing up during assembly reflow. * Case Size D, E, P, Y and X **Case Size A, B, C, H, I, K, M, R, S, T, U, V, W and Z Construction Polymer /Ta2O5/Ta Silver Adhesive Silver Paint Washer Leadframe (-Cathode) Leadframe (+Anode) Carbon Tantalum Wire Weld © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2016-1 • 1/17/2011 8 KEMET Organic Capacitor (KO-CAP) – T521 High Voltage Polymer Tantalum Capacitor Marking (KO) KEMET Organic Polymer Rated Voltage KO Polarity Indicator (+) 336 Picofarad Code 25 K 030 KEMET ID PWC* * 030 = 30th week of 2010 Storage All KO-Cap series are shipped in moisture barrier bags with a desiccant and moisture indicator card. These series are classified as MSL3 (Moisture Sensitivity Level 3). Product contained within the moisture barrier bags should be stored in normal working environments with temperatures not to exceed 40°C and humidity not in excess of 60% RH. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2016-1 • 1/17/2011 9 KEMET Organic Capacitor (KO-CAP) – T521 High Voltage Polymer Tantalum Tape & Reel Packaging Information KEMET’s Molded Tantalum and Aluminum Chip Capacitor families are packaged in 8 mm and 12 mm plastic tape on 7" and 13" reels, in accordance with EIA Standard 481-1: Taping of Surface Mount Components for Automatic Handling. This packaging system is compatible with all tape fed automatic pick and place systems. Table 4 – Packaging Quantity Case Code KEMET R I S T M U L W Z V A B C D Y X E EIA 2012-12 3216-10 3216-12 3528-12 3528-15 6032-15 6032-19 7343-15 7343-17 7343-20 3216-18 3528-21 6032-28 7343-31 7343-40 7343-43 7260-38 Tape Width-mm 7" Reel* 13" Reel* 8 8 8 8 8 12 12 12 12 12 8 8 12 12 12 12 12 2,500 3,000 2,500 2,500 2,000 1,000 1,000 1,000 1,000 1,000 2,000 2,000 500 500 500 500 500 10,000 12,000 10,000 10,000 8,000 5,000 5,000 3,000 3,000 3,000 9,000 8,000 3,000 2,500 2,000 2,000 2,000 * No c-spec required for 7" reel packaging. C-7280 required for 13" reel packaging. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2016-1 • 1/17/2011 10 KEMET Organic Capacitor (KO-CAP) – T521 High Voltage Polymer Tantalum Figure 1 – Embossed (Plastic) Carrier Tape Dimensions P2 T T2 ØDo Po [10 pitches cumulative tolerance on tape ±0.2 mm] E1 Ao F Ko B1 E2 Bo S1 W P1 T1 Center Lines of Cavity ØD 1 Cover Tape B 1 is for tape feeder reference only, including draft concentric about B o. Embossment For cavity size, see Note 1 Table 5 User Direction of Unreeling Table 5 – Embossed (Plastic) Carrier Tape Dimensions Metric will govern Constant Dimensions — Millimeters (Inches) Tape Size D0 8mm 12mm 1.5 +0.10/-0.0 (0.059 +0.004/-0.0) 16mm D1 Min. Note 1 1.0 (0.039) 1.5 (0.059) E1 P0 P2 1.75 ± 0.10 (0.069 ± 0.004) 4.0 ± 0.10 (0.157 ± 0.004) 2.0 ± 0.05 (0.079 ± 0.002) R Ref. Note 2 25.0 (0.984) 30 (1.181) S1 Min. Note 3 T Max. T1 Max. 0.600 (0.024) 0.600 (0.024) 0.100 (0.004) Variable Dimensions — Millimeters (Inches) Tape Size Pitch 8mm Single (4mm) 12mm Single (4mm) & Double (8mm) 16mm Triple (12mm) B1 Max. Note 4 4.35 (0.171) 8.2 (0.323) 12.1 (0.476) E2 Min. F P1 T2 Max W Max A0,B0 & K0 6.25 (0.246) 10.25 (0.404) 14.25 (0.561) 3.5 ± 0.05 (0.138 ± 0.002) 5.5 ± 0.05 (0.217 ± 0.002) 5.5 ± 0.05 (0.217 ± 0.002) 4.0 ± 0.10 (0.157 ± 0.004) 8.0 ± 0.10 (0.315 ± 0.004) 8.0 ± 0.10 (0.315 ± 0.004) 2.5 (0.098) 4.6 (0.181) 4.6 (0.181) 8.3 (0.327) 12.3 (0.484) 16.3 (0.642) Note 5 1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and hole location shall be applied independent of each other. 2. The tape with or without components shall pass around R without damage (see Figure 5). 3. If S1<1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Document 481 paragraph 4.3 (b)). 4. B1 dimension is a reference dimension for tape feeder clearance only. 5. The cavity defined by A0, B0 and K0 shall surround the component with sufficient clearance that: (a) the component does not protrude above the top surface of the carrier tape. (b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed. (c) rotation of the component is limited to 20° maximum for 8 and 12mm tapes and 10° maximum for 16mm tapes (see Figure 3). (d) lateral movement of the component is restricted to 0.5 mm maximum for 8mm and 12mm wide tape and to 1.0mm maximum for 16mm tape (see Figure 4). (e) for KPS Series product A0 and B0 are measured on a plane 0.3mm above the bottom of the pocket. (f) see Addendum in EIA Document 481 for standards relating to more precise taping requirements. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2016-1 • 1/17/2011 11 KEMET Organic Capacitor (KO-CAP) – T521 High Voltage Polymer Tantalum Packaging Information Performance Notes 1. Cover Tape Break Force: 1.0 Kg Minimum. 2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be: Tape Width Peel Strength 8mm 12mm & 16mm 0.1 Newton to 1.0 Newton (10gf to 100gf) 0.1 Newton to 1.3 Newton (10gf to 130gf) The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier tape shall be 165° to 180° from the plane of the carrier tape. During peeling, the carrier and/or cover tape shall be pulled at a velocity of 300±10 mm/minute. 3. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA-556 and EIA-624. Figure 3 – Maximum Component Rotation ° T Maximum Component Rotation Top View Maximum Component Rotation Side View Typical Pocket Centerline Tape Width (mm) 8,12 16-200 Bo Maximum Rotation ( 20 10 ° T) Typical Component Centerline Ao ° s Tape Width (mm) 8,12 16-56 72-200 Maximum Rotation ( 20 10 5 ° S) Figure 4 – Maximum Lateral Movement 8mm & 12mm Tape 16mm Tape 0.5 mm maximum 0.5 mm maximum 1.0 mm maximum 1.0 mm maximum Figure 5 – Bending Radius Embossed Carrier R Punched Carrier Bending Radius R © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2016-1 • 1/17/2011 12 KEMET Organic Capacitor (KO-CAP) – T521 High Voltage Polymer Tantalum Figure 6 – Reel Dimensions Full Radius, See Note W3 (Includes Access Hole at Slot Location (Ø 40 mm min.) flange distortion at outer edge) W2 (Measured at hub) D A (See Note) N C (Arbor hole diameter) B (see Note) W1 (Measured at hub) If present, tape slot in core for tape start: 2.5 mm min. width x 10.0 mm min. depth Note: Drive spokes optional; if used, dimensions B and D shall apply. Table 7 – Reel Dimensions Metric will govern Constant Dimensions — Millimeters (Inches) Tape Size A B Min C D Min 8mm 178 ± 0.20 (7.008 ± 0.008) or 330 ± 0.20 (13.000 ± 0.008) 1.5 (0.059) 13.0 +0.5/-0.2 (0.521 +0.02/-0.008) 20.2 (0.795) 12mm 16mm Variable Dimensions — Millimeters (Inches) Tape Size N Min 8mm 12mm 16mm 50 (1.969) W1 8.4 +1.5/-0.0 (0.331 +0.059/-0.0) 12.4 +2.0/-0.0 (0.488 +0.078/-0.0) 16.4 +2.0/-0.0 (0.646 +0.078/-0.0) © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com W2 Max 14.4 (0.567) 18.4 (0.724) 22.4 (0.882) W3 Shall accommodate tape width without interference T2016-1 • 1/17/2011 13 KEMET Organic Capacitor (KO-CAP) – T521 High Voltage Polymer Tantalum Figure 7 – Tape Leader & Trailer Dimensions Embossed Carrier Carrier Tape Punched Carrier 8 mm & 12 mm only Round Sprocket Holes END START Top Cover Tape Elongated Sprocket Holes (32 mm tape and wider) Trailer 160 mm minimum, Components 100 mm Min. Leader 400 mm Minimum, Top Cover Tape Figure 8 – Maximum Camber Elongated sprocket holes (32 mm & wider tapes) Carrier Tape Round Sprocket Holes 1 mm maximum, either direction Straight Edge 250 mm © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2016-1 • 1/17/2011 14 KEMET Organic Capacitor (KO-CAP) – T521 High Voltage Polymer Tantalum Other KEMET Resources Tools Resource Location Configure A Part: CapEdge http://capacitoredge.kemet.com SPICE & FIT Software http://www.kemet.com/spice Search Our FAQs: KnowledgeEdge http://www.kemet.com/keask Product Information Resource Location Products Technical Resources (Including Soldering Techniques) RoHS Statement Quality Documents http://www.kemet.com/products http://www.kemet.com/technicalpapers http://www.kemet.com/rohs http://www.kemet.com/qualitydocuments Product Request Resource Location Sample Request Engineering Kit Request http://www.kemet.com/sample http://www.kemet.com/kits Contact Resource Location Website Contact Us Investor Relations www.kemet.com http://www.kemet.com/contact http://www.kemet.com/ir Call Us 1-877-MyKEMET Twitter http://twitter.com/kemetcapacitors Disclaimer All product specifications, statements, information and data (collectively, the “Information”) are subject to change without notice. All Information given herein is believed to be accurate and reliable, but is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on our knowledge of typical operating conditions for such applications, but are not intended to constitute – and we specifically disclaim – any warranty concerning suitability for a specific customer application or use. This Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by us with reference to the use of our products is given gratis, and we assume no obligation or liability for the advice given or results obtained. Although we design and manufacture our products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated or that other measures may not be required. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2016-1 • 1/17/2011 15 KEMET Organic Capacitor (KO-CAP) – T521 High Voltage Polymer Tantalum KEMET Corporation World Headquarters Europe Asia 2835 KEMET Way Simpsonville, SC 29681 Southern Europe Geneva, Switzerland Tel: 41-22-715-0100 Northeast Asia Paris, France Tel: 33-1-4646-1009 Shenzhen, China Tel: 86-755-2518-1306 Sasso Marconi, Italy Tel: 39-051-939111 Beijing, China Tel: 86-10-5829-1711 Milan, Italy Tel: 39-02-57518176 Shanghai, China Tel: 86-21-6447-0707 Fort Lauderdale, FL Tel: 954-766-2800 Rome, Italy Tel: 39-06-23231718 Taipei, Taiwan Tel: 886-2-27528585 North America Madrid, Spain Tel: 34-91-804-4303 Southeast Asia Mailing Address: P.O. Box 5928 Greenville, SC 29606 www.kemet.com Tel: 864-963-6300 Fax: 864-963-6521 Corporate Offices Southeast Lake Mary, FL Tel: 407-855-8886 Northeast Wilmington, MA Tel: 978-658-1663 West Chester, PA Tel: 610-692-4642 Central Europe Hong Kong Tel: 852-2305-1168 Singapore Tel: 65-6586-1900 Landsberg, Germany Tel: 49-8191-3350800 Penang, Malaysia Tel: 60-4-6430200 Dortmund, Germany Tel: 49-2307-3619672 Bangalore, India Tel: 91-806-53-76817 Kwidzyn, Poland Tel: 48-55-279-7025 Central Schaumburg, IL Tel: 847-882-3590 Carmel, IN Tel: 317-706-6742 West Milpitas, CA Tel: 408-433-9950 Mexico Zapopan, Jalisco Tel: 52-33-3123-2141 Northern Europe Bishop’s Stortford, United Kingdom Tel: 44-1279-757201 Weymouth, United Kingdom Tel: 44-1305-830747 Coatbridge, Scotland Tel: 44-1236-434455 Färjestaden, Sweden Tel: 46-485-563934 Espoo, Finland Tel: 358-9-5406-5000 Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of KEMET Electronics Corporation. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2016-1 • 1/17/2011 16