CY7C1460SV25/CY7C1462SV25, 36-Mbit (1M × 36/2M × 18) Pipelined SRAM with NoBL™ Architecture Datasheet.pdf

CY7C1460SV25
CY7C1462SV25
36-Mbit (1M × 36/2M × 18)
Pipelined SRAM with NoBL™ Architecture
36-Mbit (1M × 36/2M × 18) Pipelined SRAM with NoBL™ Architecture
Features
Functional Description
■
Pin compatible and functionally equivalent to ZBT™
■
Supports 250-MHz bus operations with zero wait states
❐ Available speed grades are 250 and 167 MHz
■
Internally self-timed output buffer control to eliminate the need
to use asynchronous OE
■
Fully registered (inputs and outputs) for pipelined operation
■
Byte Write capability
■
2.5-V core power supply
The
CY7C1460SV25/CY7C1462SV25
are
2.5 V,
1M × 36/2M × 18 Synchronous pipelined burst SRAMs with
No Bus Latency™ (NoBL logic, respectively. They are
designed to support unlimited true back to back Read/Write
operations
with
no
wait
states.
The
CY7C1460SV25/CY7C1462SV25 are equipped with the
advanced (NoBL) logic required to enable consecutive
Read/Write operations with data being transferred on every clock
cycle. This feature dramatically improves the throughput of data
in systems that require frequent Write/Read transitions.
CY7C1460SV25/CY7C1462SV25 are pin compatible and
functionally equivalent to ZBT devices.
■
2.5-V I/O power supply
■
Fast clock-to-output times
❐ 2.6 ns (for 250-MHz device)
■
Clock Enable (CEN) pin to suspend operation
■
Synchronous self-timed writes
■
CY7C1460SV25 available in JEDEC-standard Pb-free 100-pin
TQFP package and non Pb-free 165-ball FBGA package.
CY7C1462SV25 available in Pb-free 100-pin TQFP package
■
IEEE 1149.1 JTAG-Compatible Boundary Scan
■
Burst capability – linear or interleaved burst order
■
“ZZ” Sleep Mode option and Stop Clock option
All synchronous inputs pass through input registers controlled by
the rising edge of the clock. All data outputs pass through output
registers controlled by the rising edge of the clock. The clock
input is qualified by the Clock Enable (CEN) signal, which when
deasserted suspends operation and extends the previous clock
cycle. Write operations are controlled by the Byte Write Selects
(BWa–BWd for CY7C1460SV25 and BWa–BWb for
CY7C1462SV25) and a Write Enable (WE) input. All writes are
conducted with on-chip synchronous self-timed write circuitry.
Three synchronous Chip Enables (CE1, CE2, CE3) and an
asynchronous Output Enable (OE) provide for easy bank
selection and output tristate control. To avoid bus contention, the
output drivers are synchronously tristated during the data portion
of a write sequence.
Selection Guide
Description
Maximum access time
Maximum operating current
Maximum CMOS standby current
Cypress Semiconductor Corporation
Document Number: 001-43804 Rev. *J
•
198 Champion Court
•
250 MHz
167 MHz
Unit
2.6
435
120
3.4
335
120
ns
mA
mA
San Jose, CA 95134-1709
•
408-943-2600
Revised April 7, 2016
CY7C1460SV25
CY7C1462SV25
Logic Block Diagram – CY7C1460SV25
ADDRESS
REGISTER 0
A0, A1, A
A1
A1'
D1
Q1
A0
A0'
BURST
D0
Q0
LOGIC
MODE
CLK
CEN
ADV/LD
C
C
WRITE ADDRESS
REGISTER 1
WRITE ADDRESS
REGISTER 2
ADV/LD
WRITE REGISTRY
AND DATA COHERENCY
CONTROL LOGIC
BWa
BWb
BWc
BWd
MEMORY
ARRAY
WRITE
DRIVERS
O
U
T
P
U
T
S
E
N
S
E
R
E
G
I
S
T
E
R
S
A
M
P
S
WE
S
T
E
E
R
I
N
G
E
INPUT
REGISTER 1 E
OE
CE1
CE2
CE3
O
U
T
P
U
T
D
A
T
A
B
U
F
F
E
R
S
DQs
DQPa
DQPb
DQPc
DQPd
E
INPUT
REGISTER 0
E
READ LOGIC
SLEEP
CONTROL
ZZ
Logic Block Diagram – CY7C1462SV25
A0, A1, A
ADDRESS
REGISTER 0
A1
A1'
D1
Q1
A0
BURST A0'
D0
Q0
LOGIC
MODE
CLK
CEN
ADV/LD
C
C
WRITE ADDRESS
REGISTER 1
WRITE ADDRESS
REGISTER 2
ADV/LD
BWa
WRITE REGISTRY
AND DATA COHERENCY
CONTROL LOGIC
WRITE
DRIVERS
MEMORY
ARRAY
BWb
WE
S
E
N
S
E
A
M
P
S
O
U
T
P
U
T
R
E
G
I
S
T
E
R
S
D
A
T
A
S
T
E
E
R
I
N
G
E
INPUT
REGISTER 1 E
OE
CE1
CE2
CE3
ZZ
Document Number: 001-43804 Rev. *J
O
U
T
P
U
T
B
U
F
F
E
R
S
DQs
DQPa
DQPb
E
INPUT
REGISTER 0 E
READ LOGIC
Sleep
Control
Page 2 of 31
CY7C1460SV25
CY7C1462SV25
Contents
Pin Configurations ........................................................... 4
Pin Definitions .................................................................. 6
Functional Overview ........................................................ 7
Single Read Accesses ................................................ 7
Burst Read Accesses .................................................. 7
Single Write Accesses ................................................. 7
Burst Write Accesses .................................................. 8
Sleep Mode ................................................................. 8
Interleaved Burst Address Table ................................. 8
Linear Burst Address Table ......................................... 8
ZZ Mode Electrical Characteristics .............................. 8
Truth Table ........................................................................ 9
Partial Write Cycle Description ..................................... 10
IEEE 1149.1 Serial Boundary Scan (JTAG) .................. 11
Disabling the JTAG Feature ...................................... 11
Test Access Port (TAP) ............................................. 11
PERFORMING A TAP RESET .................................. 11
TAP REGISTERS ...................................................... 11
TAP Instruction Set ................................................... 11
TAP Controller State Diagram ....................................... 13
TAP Controller Block Diagram ...................................... 14
TAP Timing ...................................................................... 15
TAP AC Switching Characteristics ............................... 15
2.5 V TAP AC Test Conditions ....................................... 16
2.5 V TAP AC Output Load Equivalent ......................... 16
TAP DC Electrical Characteristics
and Operating Conditions ............................................. 16
Document Number: 001-43804 Rev. *J
Identification Register Definitions ................................ 17
Scan Register Sizes ....................................................... 17
Identification Codes ....................................................... 17
Boundary Scan Order .................................................... 18
Maximum Ratings ........................................................... 19
Operating Range ............................................................. 19
Electrical Characteristics ............................................... 19
DC Electrical Characteristics ..................................... 19
Capacitance .................................................................... 20
Thermal Resistance ........................................................ 20
AC Test Loads and Waveforms ..................................... 20
Switching Characteristics .............................................. 21
Switching Waveforms .................................................... 22
Ordering Information ...................................................... 25
Ordering Code Definitions ......................................... 25
Package Diagrams .......................................................... 26
Acronyms ........................................................................ 28
Document Conventions ................................................. 28
Units of Measure ....................................................... 28
Document History Page ................................................. 29
Sales, Solutions, and Legal Information ...................... 31
Worldwide Sales and Design Support ....................... 31
Products .................................................................... 31
PSoC®Solutions ....................................................... 31
Cypress Developer Community ................................. 31
Technical Support ..................................................... 31
Page 3 of 31
CY7C1460SV25
CY7C1462SV25
Pin Configurations
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
CY7C1462SV25
(2M × 18)
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
A
NC
NC
VDDQ
VSS
NC
DQPa
DQa
DQa
VSS
VDDQ
DQa
DQa
VSS
NC
VDD
ZZ
DQa
DQa
VDDQ
VSS
DQa
DQa
NC
NC
VSS
VDDQ
NC
NC
NC
A
A
A
A
A
A
A
A
NC/72M
VSS
VDD
A
A
A
A
A
A
A
A
NC/72M
VSS
VDD
NC/144M
NC/288M
MODE
A
A
A
A
A1
A0
Document Number: 001-43804 Rev. *J
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
NC/288M
(1M × 36)
NC
DQPb
NC
DQb
NC
DQb
VDDQ VDDQ
VSS
VSS
NC
DQb
DQb
NC
DQb
DQb
DQb
DQb
VSS
VSS
VDDQ VDDQ
DQb
DQb
DQb
DQb
NC
VSS
VDD
NC
NC
VDD
VSS
ZZ
DQb
DQa
DQa
DQb
VDDQ VDDQ
VSS
VSS
DQa
DQb
DQa
DQb
DQa DQPb
DQa
NC
VSS
VSS
VDDQ VDDQ
NC
DQa
DQa
NC
DQPa
NC
NC/144M
CY7C1460SV25
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
DQc
DQc
NC
VDD
NC
VSS
DQd
DQd
VDDQ
VSS
DQd
DQd
DQd
DQd
VSS
VDDQ
DQd
DQd
DQPd
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
VSS
DQc
DQc
DQc
DQc
VSS
VDDQ
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
MODE
A
A
A
A
A1
A0
DQPc
DQc
DQc
VDDQ
A
A
A
A
CE1
CE2
NC
NC
BWb
BWa
CE3
VDD
VSS
CLK
WE
CEN
OE
ADV/LD
A
A
A
A
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
A
A
CE1
CE2
BWd
BWc
BWb
BWa
CE3
VDD
VSS
CLK
WE
CEN
OE
ADV/LD
A
A
Figure 1. 100-pin TQFP (14 × 20 × 1.4 mm) pinout
Page 4 of 31
CY7C1460SV25
CY7C1462SV25
Pin Configurations (continued)
Figure 2. 165-ball FBGA (15 × 17 × 1.4 mm) pinout
CY7C1460SV25 (1M × 36)
1
2
3
4
5
6
7
8
9
10
11
A
B
C
D
E
F
G
H
J
K
L
M
N
P
NC/576M
A
CE1
CE2
BWc
BWb
CE3
CEN
ADV/LD
A
A
NC
BWa
VSS
CLK
WE
VSS
VSS
OE
VSS
VDD
A
A
NC
VSS
VSS
VDDQ
VDDQ
NC
DQb
DQPb
DQb
R
MODE
NC/1G
A
DQPc
DQc
NC
DQc
VDDQ
VDDQ
BWd
VSS
VDD
DQc
DQc
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQb
DQb
DQc
DQc
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQb
DQb
DQc
NC
DQd
DQc
NC
DQd
VDDQ
NC
VDDQ
VDD
VDD
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VDD
VDDQ
NC
VDDQ
DQb
NC
DQa
DQb
ZZ
DQa
DQd
DQd
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQa
DQa
DQd
DQd
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQa
DQa
DQd
DQPd
DQd
NC
VDDQ
VDDQ
VDD
VSS
VSS
NC
VSS
NC
VSS
NC
VDD
VSS
VDDQ
VDDQ
DQa
NC
DQa
DQPa
A
A
TDI
A1
TDO
A
A
A
A
A
TMS
A0
TCK
A
A
A
NC/144M NC/72M
A
Document Number: 001-43804 Rev. *J
VSS
NC/288M
A
Page 5 of 31
CY7C1460SV25
CY7C1462SV25
Pin Definitions
Pin Name
I/O Type
Pin Description
A0, A1, A
InputAddress Inputs Used to Select One of the Address Locations. Sampled at the rising edge of the
Synchronous CLK.
BWa, BWb,
BWc, BWd
InputByte Write Select Inputs, Active LOW. Qualified with WE to conduct writes to the SRAM. Sampled
Synchronous on the rising edge of CLK. BWa controls DQa and DQPa, BWb controls DQb and DQPb, BWc controls
DQc and DQPc, BWd controls DQd and DQPd.
WE
InputWrite Enable Input, Active LOW. Sampled on the rising edge of CLK if CEN is active LOW. This
Synchronous signal must be asserted LOW to initiate a write sequence.
ADV/LD
InputAdvance/Load Input Used to Advance the On Chip Address Counter or Load a New Address.
Synchronous When HIGH (and CEN is asserted LOW) the internal burst counter is advanced. When LOW, a new
address can be loaded into the device for an access. After being deselected, ADV/LD should be driven
LOW to load a new address.
CLK
InputClock
Clock Input. Used to capture all synchronous inputs to the device. CLK is qualified with CEN. CLK
is only recognized if CEN is active LOW.
CE1
InputChip Enable 1 Input, Active LOW. Sampled on the rising edge of CLK. Used in conjunction with CE2
Synchronous and CE3 to select/deselect the device.
CE2
InputChip Enable 2 Input, Active HIGH. Sampled on the rising edge of CLK. Used in conjunction with
Synchronous CE1 and CE3 to select/deselect the device.
CE3
InputChip Enable 3 Input, Active LOW. Sampled on the rising edge of CLK. Used in conjunction with CE1
Synchronous and CE2 to select/deselect the device.
OE
InputOutput Enable, Active LOW. Combined with the synchronous logic block inside the device to control
Asynchronous the direction of the I/O pins. When LOW, the I/O pins are allowed to behave as outputs. When
deasserted HIGH, I/O pins are tristated, and act as input data pins. OE is masked during the data
portion of a write sequence, during the first clock when emerging from a deselected state and when
the device has been deselected.
CEN
InputClock Enable Input, Active LOW. When asserted LOW the clock signal is recognized by the SRAM.
Synchronous When deasserted HIGH the clock signal is masked. Since deasserting CEN does not deselect the
device, CEN can be used to extend the previous cycle when required.
DQa, DQb,
DQc, DQd
I/OBidirectional Data I/O Lines. As inputs, they feed into an on-chip data register that is triggered by
Synchronous the rising edge of CLK. As outputs, they deliver the data contained in the memory location specified
by AX during the previous clock rise of the read cycle. The direction of the pins is controlled by OE
and the internal control logic. When OE is asserted LOW, the pins can behave as outputs. When
HIGH, DQa–DQd are placed in a tristate condition. The outputs are automatically tristated during the
data portion of a write sequence, during the first clock when emerging from a deselected state, and
when the device is deselected, regardless of the state of OE.
I/OBidirectional Data Parity I/O Lines. Functionally, these signals are identical to DQ[31:0]. During write
DQPa,
DQPb,
Synchronous sequences, DQPa is controlled by BWa, DQPb is controlled by BWb, DQPc is controlled by BWc, and
DQPc, DQPd
DQPd is controlled by BWd.
MODE
Input Strap Pin Mode Input. Selects the burst order of the device. Tied HIGH selects the interleaved burst order.
Pulled LOW selects the linear burst order. MODE should not change states during operation. When
left floating MODE defaults HIGH, to an interleaved burst order.
TDO
JTAG serial Serial data Out to the JTAG Circuit. Delivers data on the negative edge of TCK.
output
Synchronous
TDI
JTAG serial Serial data In to the JTAG Circuit. Sampled on the rising edge of TCK.
input
Synchronous
TMS
Test Mode
This pin controls the Test Access Port State Machine. Sampled on the rising edge of TCK.
Select
Synchronous
Document Number: 001-43804 Rev. *J
Page 6 of 31
CY7C1460SV25
CY7C1462SV25
Pin Definitions (continued)
Pin Name
I/O Type
TCK
JTAG-Clock
VDD
Pin Description
Clock input to the JTAG Circuitry.
Power Supply Power supply inputs to the core of the device.
VDDQ
I/O Power
Supply
VSS
NC
NC/72M
Ground
N/A
N/A
NC/144M
N/A
Not connected to the Die. Can be tied to any voltage level.
NC/288M
N/A
Not connected to the Die. Can be tied to any voltage level.
NC/576M
N/A
Not connected to the Die. Can be tied to any voltage level.
NC/1G
N/A
Not Connected to the Die. Can be tied to any voltage level.
ZZ
Power supply for the I/O circuitry.
Ground for the device. Should be connected to ground of the system.
No Connects. This pin is not connected to the die.
Not connected to the Die. Can be tied to any voltage level.
InputZZ “sleep” Input. This active HIGH input places the device in a non time critical “sleep” condition
Asynchronous with data integrity preserved. During normal operation, this pin must be LOW or left floating.
ZZ pin has an internal pull down.
Functional Overview
The CY7C1460SV25/CY7C1462SV25 are synchronous
pipelined Burst NoBL SRAMs designed specifically to eliminate
wait states during Write/Read transitions. All synchronous inputs
pass through input registers controlled by the rising edge of the
clock. The clock signal is qualified with the Clock Enable input
signal (CEN). If CEN is HIGH, the clock signal is not recognized
and all internal states are maintained. All synchronous
operations are qualified with CEN. All data outputs pass through
output registers controlled by the rising edge of the clock.
Maximum access delay from the clock rise (tCO) is 2.6 ns
(250-MHz device).
Accesses can be initiated by asserting all three Chip Enables
(CE1, CE2, CE3) active at the rising edge of the clock. If Clock
Enable (CEN) is active LOW and ADV/LD is asserted LOW, the
address presented to the device is latched. The access can
either be a read or write operation, depending on the status of
the Write Enable (WE). BW[x] can be used to conduct byte write
operations.
Write operations are qualified by the Write Enable (WE). All
writes are simplified with on-chip synchronous self-timed write
circuitry.
Three synchronous Chip Enables (CE1, CE2, CE3) and an
asynchronous Output Enable (OE) simplify depth expansion. All
operations (Reads, Writes, and Deselects) are pipelined.
ADV/LD should be driven LOW after the device has been
deselected to load a new address for the next operation.
Single Read Accesses
A read access is initiated when the following conditions are
satisfied at clock rise: (1) CEN is asserted LOW, (2) CE1, CE2,
and CE3 are ALL asserted active, (3) the Write Enable input
signal WE is deasserted HIGH, and (4) ADV/LD is asserted
LOW. The address presented to the address inputs is latched
into the Address Register and presented to the memory core and
control logic. The control logic determines that a read access is
in progress and allows the requested data to propagate to the
Document Number: 001-43804 Rev. *J
input of the output register. At the rising edge of the next clock
the requested data is allowed to propagate through the output
register and on to the data bus within 2.6 ns (250-MHz device)
provided OE is active LOW. After the first clock of the read
access the output buffers are controlled by OE and the internal
control logic. OE must be driven LOW for the device to drive out
the requested data. During the second clock, a subsequent
operation (Read/Write/Deselect) can be initiated. Deselecting
the device is also pipelined. Therefore, when the SRAM is
deselected at clock rise by one of the chip enable signals, its
output tristates following the next clock rise.
Burst Read Accesses
The CY7C1460SV25/CY7C1462SV25 have an on-chip burst
counter that allows the user the ability to supply a single address
and conduct up to four Reads without reasserting the address
inputs. ADV/LD must be driven LOW to load a new address into
the SRAM, as described in the Single Read Accesses section.
The sequence of the burst counter is determined by the MODE
input signal. A LOW input on MODE selects a linear burst mode,
a HIGH selects an interleaved burst sequence. Both burst
counters use A0 and A1 in the burst sequence, and wraps
around when incremented sufficiently. A HIGH input on ADV/LD
increments the internal burst counter regardless of the state of
chip enables inputs or WE. WE is latched at the beginning of a
burst cycle. Therefore, the type of access (Read or Write) is
maintained throughout the burst sequence.
Single Write Accesses
Write access are initiated when the following conditions are
satisfied at clock rise: (1) CEN is asserted LOW, (2) CE1, CE2,
and CE3 are ALL asserted active, and (3) the write signal WE is
asserted LOW. The address presented to the address inputs is
loaded into the Address Register. The write signals are latched
into the Control Logic block.
On the subsequent clock rise the data lines are automatically
tristated regardless of the state of the OE input signal. This
allows the external logic to present the data on DQ and DQP
(DQa,b,c,d/DQPa,b,c,d for CY7C1460SV25 and DQa,b/DQPa,b for
Page 7 of 31
CY7C1460SV25
CY7C1462SV25
CY7C1462SV25). In addition, the address for the subsequent
access (Read/Write/Deselect) is latched into the Address
Register (provided the appropriate control signals are asserted).
driven in each cycle of the burst write to write the correct bytes
of data.
Sleep Mode
On the next clock rise, the data presented to DQ and DQP
(DQa,b,c,d/DQPa,b,c,d for CY7C1460SV25 and DQa,b/DQPa,b for
CY7C1462SV25) (or a subset for byte write operations, see
Write Cycle Description table for details) inputs is latched into the
device and the write is complete.
The ZZ input pin is an asynchronous input. Asserting ZZ places
the SRAM in a power conservation “sleep” mode. Two clock
cycles are required to enter into or exit from this “sleep” mode.
While in this mode, data integrity is guaranteed. Accesses
pending when entering the “sleep” mode are not considered valid
nor is the completion of the operation guaranteed. The device
must be deselected prior to entering the “sleep” mode. CE1, CE2,
and CE3, must remain inactive for the duration of tZZREC after the
ZZ input returns LOW.
The data written during the Write operation is controlled by BW
(BWa,b,c,d for CY7C1460SV25 and BWa,b for CY7C1462SV25)
signals. The CY7C1460SV25/CY7C1462SV25 provides byte
write capability that is described in the Write Cycle Description
table. Asserting the Write Enable input (WE) with the selected
Byte Write Select (BW) input selectively writes to only the desired
bytes. Bytes not selected during a byte write operation remains
unaltered. A synchronous self timed write mechanism has been
provided to simplify the write operations. Byte write capability
has been included to greatly simplify Read/Modify/Write
sequences, which can be reduced to simple byte write
operations.
Interleaved Burst Address Table
(MODE = Floating or VDD)
Because CY7C1460SV25/CY7C1462SV25 are common I/O
devices, data should not be driven into the device while the
outputs are active. The Output Enable (OE) can be deasserted
HIGH before presenting data to the DQ and DQP
(DQa,b,c,d/DQPa,b,c,d for CY7C1460SV25 and DQa,b/DQPa,b for
CY7C1462SV25) inputs. Doing so tristates the output drivers. As
a safety precaution, DQ and DQP (DQa,b,c,d/DQPa,b,c,d for
CY7C1460SV25 and DQa,b/DQPa,b for CY7C1462SV25) are
automatically tristated during the data portion of a write cycle,
regardless of the state of OE.
First
Address
A1:A0
Second
Address
A1:A0
Third
Address
A1:A0
Fourth
Address
A1:A0
00
01
10
11
01
00
11
10
10
11
00
01
11
10
01
00
Linear Burst Address Table
(MODE = GND)
Burst Write Accesses
The CY7C1460SV25/CY7C1462SV25 has an on-chip burst
counter that allows the user the ability to supply a single address
and conduct up to four WRITE operations without reasserting the
address inputs. ADV/LD must be driven LOW to load the initial
address, as described in the Single Write Access section. When
ADV/LD is driven HIGH on the subsequent clock rise, the chip
enables (CE1, CE2, and CE3) and WE inputs are ignored and the
burst counter is incremented. The correct BW (BWa,b,c,d for
CY7C1460SV25 and BWa,b for CY7C1462SV25) inputs must be
First
Address
A1:A0
Second
Address
A1:A0
Third
Address
A1:A0
Fourth
Address
A1:A0
00
01
10
11
01
10
11
00
10
11
00
01
11
00
01
10
ZZ Mode Electrical Characteristics
Min
Max
Unit
IDDZZ
Parameter
Sleep mode standby current
Description
ZZ  VDD 0.2 V
–
100
mA
tZZS
Device operation to ZZ
ZZVDD  0.2 V
–
2tCYC
ns
tZZREC
ZZ recovery time
ZZ 0.2 V
2tCYC
–
ns
tZZI
ZZ active to sleep current
This parameter is sampled
–
2tCYC
ns
tRZZI
ZZ Inactive to exit sleep current
This parameter is sampled
0
–
ns
Document Number: 001-43804 Rev. *J
Test Conditions
Page 8 of 31
CY7C1460SV25
CY7C1462SV25
Truth Table
Truth table for CY7C1460SV25/CY7C1462SV25 follows. [1, 2, 3, 4, 5, 6, 7]
Deselect Cycle
Address Used CE ZZ ADV/LD WE BWx OE CEN CLK
None
H
L
L
X
X
X
L
L–H
Tristate
Continue Deselect Cycle
None
X
L
H
X
X
X
L
L–H
Tristate
Read Cycle (Begin Burst)
External
L
L
L
H
X
L
L
L–H Data Out (Q)
Read Cycle (Continue Burst)
Next
X
L
H
X
X
L
L
L–H Data Out (Q)
NOP/Dummy Read (Begin Burst)
External
L
L
L
H
X
H
L
L–H
Tristate
Dummy Read (Continue Burst)
Next
X
L
H
X
X
H
L
L–H
Tristate
Write Cycle (Begin Burst)
External
L
L
L
L
L
X
L
L–H
Data In (D)
Write Cycle (Continue Burst)
Next
X
L
H
X
L
X
L
L–H
Data In (D)
NOP/WRITE ABORT (Begin Burst)
None
L
L
L
L
H
X
L
L–H
Tristate
WRITE ABORT (Continue Burst)
Next
X
L
H
X
H
X
L
L–H
Tristate
IGNORE CLOCK EDGE (Stall)
Current
X
L
X
X
X
X
H
L–H
–
Sleep MODE
None
X
H
X
X
X
X
X
X
Tristate
Operation
DQ
Notes
1. X = “Don't Care”, H = Logic HIGH, L = Logic LOW, CE stands for ALL Chip Enables active. BWx = L signifies at least one Byte Write Select is active, BWx = Valid
signifies that the desired byte write selects are asserted, see Write Cycle Description table for details.
2. Write is defined by WE and BWX. See Write Cycle Description table for details.
3. When a write cycle is detected, all IOs are tristated, even during byte writes.
4. The DQ and DQP pins are controlled by the current cycle and the OE signal.
5. CEN = H inserts wait states.
6. Device powers up deselected and the IOs in a tristate condition, regardless of OE.
7. OE is asynchronous and is not sampled with the clock rise. It is masked internally during write cycles.During a read cycle DQs and DQPX = Three-state when OE is
inactive or when the device is deselected, and DQs=data when OE is active.
Document Number: 001-43804 Rev. *J
Page 9 of 31
CY7C1460SV25
CY7C1462SV25
Partial Write Cycle Description
Partial Write Cycle Description for CY7C1460SV25/CY7C1462SV25 follows. [8, 9, 10, 11]
Function (CY7C1460SV25)
WE
BWd
BWc
BWb
BWa
Read
H
X
X
X
X
Write – No bytes written
L
H
H
H
H
Write Byte a – (DQa and DQPa)
L
H
H
H
L
Write Byte b – (DQb and DQPb)
L
H
H
L
H
Write Bytes b, a
L
H
H
L
L
Write Byte c – (DQc and DQPc)
L
H
L
H
H
Write Bytes c, a
L
H
L
H
L
Write Bytes c, b
L
H
LL
L
H
Write Bytes c, b, a
L
H
L
L
L
Write Byte d – (DQd and DQPd)
L
L
H
H
H
Write Bytes d, a
L
L
H
H
L
Write Bytes d, b
L
L
H
L
H
Write Bytes d, b, a
L
L
H
L
L
Write Bytes d, c
L
L
L
H
H
Write Bytes d, c, a
L
L
L
H
L
Write Bytes d, c, b
L
L
L
L
H
Write All Bytes
L
L
L
L
L
Function (CY7C1462SV25)
WE
BWb
BWa
Read
H
X
X
Write – No Bytes Written
L
H
H
Write Byte a – (DQa and DQPa)
L
H
L
Write Byte b – (DQb and DQPb)
L
L
H
Write Both Bytes
L
L
L
Notes
8. X = “Don't Care”, H = Logic HIGH, L = Logic LOW, CE stands for ALL Chip Enables active. BWx = L signifies at least one Byte Write Select is active, BWx = Valid
signifies that the desired byte write selects are asserted, see Write Cycle Description table for details.
9. Write is defined by WE and BWX. See Write Cycle Description table for details.
10. When a write cycle is detected, all IOs are tristated, even during byte writes.
11. Table only lists a partial listing of the byte write combinations. Any combination of BWX is valid. Appropriate write is done based on which byte write is active.
Document Number: 001-43804 Rev. *J
Page 10 of 31
CY7C1460SV25
CY7C1462SV25
IEEE 1149.1 Serial Boundary Scan (JTAG)
Data is serially loaded into the TDI ball on the rising edge of TCK.
Data is output on the TDO ball on the falling edge of TCK.
The CY7C1460SV25 incorporates a serial boundary scan test
access port (TAP). This part is fully compliant with 1149.1. The
TAP operates using JEDEC-standard 2.5 V I/O logic level.
Instruction Register
The CY7C1460SV25 contains a TAP controller, instruction
register, boundary scan register, bypass register, and ID register.
Disabling the JTAG Feature
It is possible to operate the SRAM without using the JTAG
feature. To disable the TAP controller, TCK must be tied
LOW(VSS) to prevent clocking of the device. TDI and TMS are
internally pulled up and may be unconnected. They may
alternately be connected to VDD through a pull up resistor. TDO
should be left unconnected. Upon power up, the device comes
up in a reset state which does not interfere with the operation of
the device.
Test Access Port (TAP)
Test Clock (TCK)
The test clock is used only with the TAP controller. All inputs are
captured on the rising edge of TCK. All outputs are driven from
the falling edge of TCK.
Test Mode Select (TMS)
The TMS input is used to give commands to the TAP controller
and is sampled on the rising edge of TCK. It is allowable to leave
this ball unconnected if the TAP is not used. The ball is pulled up
internally, resulting in a logic HIGH level.
Test Data In (TDI)
The TDI ball is used to serially input information into the registers
and can be connected to the input of any of the registers. The
register between TDI and TDO is chosen by the instruction that
is loaded into the TAP instruction register. For information on
loading the instruction register, see TAP Controller State
Diagram on page 13. TDI is internally pulled up and can be
unconnected if the TAP is unused in an application. TDI is
connected to the most significant bit (MSB) of any register.
Test Data Out (TDO)
The TDO output ball is used to serially clock data out from the
registers. The output is active depending upon the current state
of the TAP state machine (see Identification Codes on page 17).
The output changes on the falling edge of TCK. TDO is
connected to the least significant bit (LSB) of any register.
Performing a TAP Reset
A RESET is performed by forcing TMS HIGH (VDD) for five rising
edges of TCK. This RESET does not affect the operation of the
SRAM and may be performed while the SRAM is operating.
At power up, the TAP is reset internally to ensure that TDO
comes up in a High Z state.
TAP Registers
Registers are connected between the TDI and TDO balls and
scan data into and out of the SRAM test circuitry. Only one
register can be selected at a time through the instruction register.
Document Number: 001-43804 Rev. *J
Three-bit instructions can be serially loaded into the instruction
register. This register is loaded when it is placed between the TDI
and TDO balls as shown in the TAP Controller Block Diagram on
page 14. Upon power up, the instruction register is loaded with
the IDCODE instruction. It is also loaded with the IDCODE
instruction if the controller is placed in a reset state as described
in the previous section.
When the TAP controller is in the Capture IR state, the two least
significant bits are loaded with a binary “01” pattern to allow for
fault isolation of the board level serial test data path.
Bypass Register
To save time when serially shifting data through registers, it is
sometimes advantageous to skip certain chips. The bypass
register is a single-bit register that can be placed between the
TDI and TDO balls. This shifts data through the SRAM with
minimal delay. The bypass register is set LOW (VSS) when the
BYPASS instruction is executed.
Boundary Scan Register
The boundary scan register is connected to all the input and
bidirectional balls on the SRAM. The length of the Boundary
Scan Register for the SRAM in different packages is listed in the
Scan Register Sizes table.
The boundary scan register is loaded with the contents of the
RAM I/O ring when the TAP controller is in the Capture DR state
and is then placed between the TDI and TDO balls when the
controller is moved to the Shift DR state. The EXTEST,
SAMPLE/PRELOAD and SAMPLE Z instructions can be used to
capture the contents of the I/O ring.
The Boundary Scan Order on page 18 show the order in which
the bits are connected. Each bit corresponds to one of the bumps
on the SRAM package. The MSB of the register is connected to
TDI, and the LSB is connected to TDO.
Identification (ID) Register
The ID register is loaded with a vendor specific, 32-bit code
during the Capture DR state when the IDCODE command is
loaded in the instruction register. The IDCODE is hardwired into
the SRAM and can be shifted out when the TAP controller is in
the Shift DR state. The ID register has a vendor code and other
information described in the Identification Register Definitions on
page 17.
TAP Instruction Set
Overview
Eight different instructions are possible with the three-bit
instruction register. All combinations are listed in the
Identification Codes on page 17. Three of these instructions are
listed as RESERVED and should not be used. The other five
instructions are described in this section in detail.
Instructions are loaded into the TAP controller during the Shift IR
state when the instruction register is placed between TDI and
TDO. During this state, instructions are shifted through the
instruction register through the TDI and TDO balls. To execute
Page 11 of 31
CY7C1460SV25
CY7C1462SV25
the instruction after it is shifted in, the TAP controller is moved
into the Update IR state.
IDCODE
The IDCODE instruction loads a vendor specific, 32-bit code into
the instruction register. It also places the instruction register
between the TDI and TDO balls and shifts the IDCODE out of the
device when the TAP controller enters the Shift DR state.
The IDCODE instruction is loaded into the instruction register
upon power up or whenever the TAP controller is given a test
logic reset state.
SAMPLE Z
The SAMPLE Z instruction connects the boundary scan register
between the TDI and TDO pins when the TAP controller is in a
Shift DR state. The SAMPLE Z command puts the output bus into
a High Z state until the next command is given during the
“Update IR” state.
SAMPLE/PRELOAD
SAMPLE/PRELOAD is a 1149.1 mandatory instruction. When
the SAMPLE/PRELOAD instructions are loaded into the
instruction register and the TAP controller is in the Capture DR
state, a snapshot of data on the inputs and output pins is
captured in the boundary scan register.
The user must be aware that the TAP controller clock can only
operate at a frequency up to 20 MHz, while the SRAM clock
operates more than an order of magnitude faster. Because there
is a large difference in the clock frequencies, it is possible that
during the Capture DR state, an input or output undergoes a
transition. The TAP may then try to capture a signal while in
transition (metastable state). This does not harm the device, but
there is no guarantee as to the value that is captured.
Repeatable results may not be possible.
To guarantee that the boundary scan register captures the
correct value of a signal, the SRAM signal must be stabilized
long enough to meet the TAP controller’s capture setup plus hold
times (tCS and tCH). The SRAM clock input might not be captured
correctly if there is no way in a design to stop (or slow) the clock
during a SAMPLE/PRELOAD instruction. If this is an issue, it is
still possible to capture all other signals and simply ignore the
value of the CK and CK# captured in the boundary scan register.
After the data is captured, it is possible to shift out the data by
putting the TAP into the Shift DR state. This places the boundary
scan register between the TDI and TDO pins.
Document Number: 001-43804 Rev. *J
PRELOAD places an initial data pattern at the latched parallel
outputs of the boundary scan register cells prior to the selection
of another boundary scan test operation.
The shifting of data for the SAMPLE and PRELOAD phases can
occur concurrently when required–that is, while data captured is
shifted out, the preloaded data can be shifted in.
BYPASS
When the BYPASS instruction is loaded in the instruction register
and the TAP is placed in a Shift DR state, the bypass register is
placed between the TDI and TDO pins. The advantage of the
BYPASS instruction is that it shortens the boundary scan path
when multiple devices are connected together on a board.
EXTEST
The EXTEST instruction drives the preloaded data out through
the system output pins. This instruction also connects the
boundary scan register for serial access between the TDI and
TDO in the shift DR controller state.
EXTEST Output Bus Tristate
IEEE Standard 1149.1 mandates that the TAP controller be able
to put the output bus into a tristate mode.
The boundary scan register has a special bit located at bit #89
(for 165-ball FBGA package). When this scan cell, called the
“extest output bus tristate,” is latched into the preload register
during the “Update DR” state in the TAP controller, it directly
control the state of the output (Q-bus) pins, when the EXTEST is
entered as the current instruction. When HIGH, it enables the
output buffers to drive the output bus. When LOW, this bit places
the output bus into a High Z condition.
This bit can be set by entering the SAMPLE/PRELOAD or
EXTEST command, and then shifting the desired bit into that cell,
during the “Shift DR” state. During “Update DR,” the value loaded
into that shift register cell latches into the preload register. When
the EXTEST instruction is entered, this bit directly control the
output Q bus pins. Note that this bit is preset HIGH to enable the
output when the device is powered up, and also when the TAP
controller is in the “Test-Logic-Reset” state.
Reserved
These instructions are not implemented but are reserved for
future use. Do not use these instructions.
Page 12 of 31
CY7C1460SV25
CY7C1462SV25
TAP Controller State Diagram
1
TEST-LOGIC
RESET
0
0
RUN-TEST/
IDLE
1
SELECT
DR-SCAN
1
SELECT
IR-SCAN
0
1
0
1
CAPTURE-DR
CAPTURE-IR
0
0
SHIFT-DR
0
SHIFT-IR
1
1
EXIT1-IR
0
1
0
PAUSE-DR
0
PAUSE-IR
1
0
1
EXIT2-DR
0
EXIT2-IR
1
1
UPDATE-DR
1
0
1
EXIT1-DR
0
1
0
UPDATE-IR
1
0
The 0/1 next to each state represents the value of TMS at the rising edge of TCK.
Document Number: 001-43804 Rev. *J
Page 13 of 31
CY7C1460SV25
CY7C1462SV25
TAP Controller Block Diagram
0
Bypass Register
2 1 0
TDI
Selection
Circuitry
Instruction Register
31 30 29 .
.
. 2 1 0
Selection
Circuitry
TDO
Identification Register
x .
.
.
.
. 2 1 0
Boundary Scan Register
TCK
TMS
Document Number: 001-43804 Rev. *J
TAP CONTROLLER
Page 14 of 31
CY7C1460SV25
CY7C1462SV25
TAP Timing
Figure 3. TAP Timing
1
2
Test Clock
(TCK)
3
tTH
tTMSS
tTMSH
tTDIS
tTDIH
t
TL
4
5
6
tCYC
Test Mode Select
(TMS)
Test Data-In
(TDI)
tTDOV
tTDOX
Test Data-Out
(TDO)
DON’T CARE
UNDEFINED
TAP AC Switching Characteristics
Over the Operating Range
Parameter [9, 10]
Description
Min
Max
Unit
Clock
tTCYC
TCK Clock Cycle Time
50
–
ns
tTF
TCK Clock Frequency
–
20
MHz
tTH
TCK Clock HIGH time
20
–
ns
tTL
TCK Clock LOW time
20
–
ns
tTDOV
TCK Clock LOW to TDO Valid
–
10
ns
tTDOX
TCK Clock LOW to TDO Invalid
0
–
ns
tTMSS
TMS Setup to TCK Clock Rise
5
–
ns
tTDIS
TDI Setup to TCK Clock Rise
5
–
ns
tCS
Capture Setup to TCK Rise
5
–
ns
tTMSH
TMS Hold after TCK Clock Rise
5
–
ns
tTDIH
TDI Hold after Clock Rise
5
–
ns
tCH
Capture Hold after Clock Rise
5
–
ns
Output Times
Setup Times
Hold Times
Notes
9. tCS and tCH refer to the setup and hold time requirements of latching data from the boundary scan register.
10. Test conditions are specified using the load in TAP AC test Conditions. tR/tF = 1 ns.
Document Number: 001-43804 Rev. *J
Page 15 of 31
CY7C1460SV25
CY7C1462SV25
2.5 V TAP AC Test Conditions
2.5 V TAP AC Output Load Equivalent
1.25V
Input pulse levels ...............................................VSS to 2.5 V
Input rise and fall time ....................................................1 ns
50Ω
Input timing reference levels ......................... ..............1.25 V
Output reference levels .............................................. 1.25 V
TDO
Test load termination supply voltage .......................... 1.25 V
Z O= 50Ω
20pF
TAP DC Electrical Characteristics and Operating Conditions
(0 °C < TA < +70 °C; VDD = 2.5 V ± 0.125 V unless otherwise noted)
Parameter [11]
Min
Max
Unit
VOH1
Output HIGH Voltage
Description
IOH = –1.0 mA
Test Conditions
VDDQ = 2.5 V
1.7
–
V
VOH2
Output HIGH Voltage
IOH = –100 A
VDDQ = 2.5 V
2.1
–
V
VOL1
Output LOW Voltage
IOL = 1.0 mA
VDDQ = 2.5 V
–
0.4
V
VOL2
Output LOW Voltage
IOL = 100 A
VDDQ = 2.5 V
–
0.2
V
VIH
Input HIGH Voltage
VDDQ = 2.5 V
1.7
VDD + 0.3
V
VIL
Input LOW Voltage
VDDQ = 2.5 V
–0.3
0.7
V
IX
Input Load Current
–5
5
A
GND  VI  VDDQ
Note
11. All voltages referenced to VSS (GND).
Document Number: 001-43804 Rev. *J
Page 16 of 31
CY7C1460SV25
CY7C1462SV25
Identification Register Definitions
CY7C1460SV25
(1M × 36)
Instruction Field
Revision Number (31:29)
000
Device Depth (28:24)
01011
Description
Describes the version number
Reserved for Internal Use
Architecture/Memory Type(23:18)
001000
Defines memory type and architecture
Bus Width/Density(17:12)
100111
Defines width and density
Cypress JEDEC ID Code (11:1)
00000110100
ID Register Presence Indicator (0)
1
Allows unique identification of SRAM vendor
Indicates the presence of an ID register
Scan Register Sizes
Register Name
Bit Size (× 36)
Instruction
3
Bypass
1
ID
32
Boundary Scan Order (165-ball FBGA package)
89
Identification Codes
Code
Description
EXTEST
Instruction
000
Captures I/O ring contents. Places the boundary scan register between TDI and TDO. Forces
all SRAM outputs to High Z state.
IDCODE
001
Loads the ID register with the vendor ID code and places the register between TDI and TDO.
This operation does not affect SRAM operations.
SAMPLE Z
010
Captures I/O ring contents. Places the boundary scan register between TDI and TDO. Forces
all SRAM output drivers to a High Z state.
RESERVED
011
Do Not Use: This instruction is reserved for future use.
SAMPLE/PRELOAD
100
Captures I/O ring contents. Places the boundary scan register between TDI and TDO. Does
not affect SRAM operation.
RESERVED
101
Do Not Use: This instruction is reserved for future use.
RESERVED
110
Do Not Use: This instruction is reserved for future use.
BYPASS
111
Places the bypass register between TDI and TDO. This operation does not affect SRAM
operations.
Document Number: 001-43804 Rev. *J
Page 17 of 31
CY7C1460SV25
CY7C1462SV25
Boundary Scan Order
165-ball FBGA [12]
CY7C1460SV25 (1 M × 36)
Bit#
Ball ID
Bit#
Ball ID
Bit#
Ball ID
Bit#
Ball ID
1
N6
26
E11
51
A3
76
N1
2
N7
27
D11
52
A2
77
N2
3
N10
28
G10
53
B2
78
P1
4
P11
29
F10
54
C2
79
R1
5
P8
30
E10
55
B1
80
R2
6
R8
31
D10
56
A1
81
P3
7
R9
32
C11
57
C1
82
R3
8
P9
33
A11
58
D1
83
P2
9
P10
34
B11
59
E1
84
R4
10
R10
35
A10
60
F1
85
P4
11
R11
36
B10
61
G1
86
N5
12
H11
37
A9
62
D2
87
P6
13
N11
38
B9
63
E2
88
R6
14
M11
39
C10
64
F2
89
Internal
15
L11
40
A8
65
G2
16
K11
41
B8
66
H1
17
J11
42
A7
67
H3
18
M10
43
B7
68
J1
19
L10
44
B6
69
K1
20
K10
45
A6
70
L1
21
J10
46
B5
71
M1
22
H9
47
A5
72
J2
23
H10
48
A4
73
K2
24
G11
49
B4
74
L2
25
F11
50
B3
75
M2
Note
12. Bit# 89 is preset HIGH.
Document Number: 001-43804 Rev. *J
Page 18 of 31
CY7C1460SV25
CY7C1462SV25
Maximum Ratings
Current into Outputs (LOW) ........................................ 20 mA
Exceeding maximum ratings may shorten the useful life of the
device. User guidelines are not tested.
Storage Temperature ............................... –65 °C to +150 °C
Ambient Temperature with
Power Applied ......................................... –55 °C to +125 °C
Static Discharge Voltage
(per MIL-STD-883, Method 3015) .......................... > 2001 V
Latch-up Current .................................................... > 200 mA
Operating Range
Range
Ambient
Temperature
VDD
VDDQ
Commercial
0 °C to +70 °C
2.5 V – 5% /
+ 5%
1.7 V to VDD
Supply Voltage on VDD Relative to GND .....–0.5 V to +3.6 V
Supply Voltage on VDDQ Relative to GND .... –0.5 V to +VDD
DC to Outputs in Tristate ..................–0.5 V to VDDQ + 0.5 V
DC Input Voltage ................................ –0.5 V to VDD + 0.5 V
Electrical Characteristics
Over the Operating Range
DC Electrical Characteristics
Over the Operating Range
Parameter [14, 15]
Description
VDD
Power Supply Voltage
Test Conditions
VDDQ
I/O Supply Voltage
for 2.5 V I/O
VOH
Output HIGH Voltage
for 2.5 V I/O, IOH =1.0 mA
VOL
Output LOW Voltage
for 2.5 V I/O, IOL =1.0 mA
Min
Max
Unit
2.375
2.625
V
2.375
VDD
V
2.0
–
V
–
0.4
V
V
Input HIGH
Voltage[14]
for 2.5 V I/O
1.7
VDD + 0.3
VIL
Input LOW
Voltage[14]
for 2.5 V I/O
–0.3
0.7
V
IX
Input Leakage Current except ZZ GND  VI  VDDQ
and MODE
–5
5
A
Input Current of MODE
Input = VSS
–30
–
A
Input = VDD
–
5
A
Input = VSS
–5
–
A
Input = VDD
–
30
A
VIH
Input Current of ZZ
IOZ
Output Leakage Current
GND  VI  VDDQ, Output Disabled
–5
5
A
IDD [16]
VDD Operating Supply
VDD = Max, IOUT = 0 mA,
f = fMAX = 1/tCYC
4-ns cycle,
250 MHz
–
435
mA
6-ns cycle,
167 MHz
–
335
mA
ISB1
Automatic CE Power down
Current – TTL Inputs
Max. VDD, Device Deselected,
VIN  VIH or VIN  VIL,
f = fMAX = 1/tCYC
All speed
grades
–
185
mA
ISB2
Automatic CE Power down
Current – CMOS Inputs
Max. VDD, Device Deselected, All speed
VIN  0.3 V or VIN > VDDQ 0.3 V, grades
f=0
–
120
mA
Notes
14. Overshoot: VIH(AC) < VDD + 1.5 V (Pulse width less than tCYC/2), undershoot: VIL(AC) > –2V (Pulse width less than tCYC/2).
15. TPower-up: Assumes a linear ramp from 0 V to VDD(min.) within 200 ms. During this time VIH < VDD and VDDQ < VDD.
16. The operation current is calculated with 50% read cycle and 50% write cycle.
Document Number: 001-43804 Rev. *J
Page 19 of 31
CY7C1460SV25
CY7C1462SV25
Electrical Characteristics (continued)
Over the Operating Range
DC Electrical Characteristics (continued)
Over the Operating Range
Parameter [14, 15]
Description
Test Conditions
Min
Max
Unit
ISB3
Automatic CE Power down
Current – CMOS Inputs
Max. VDD, Device Deselected, All speed
VIN  0.3 V or VIN > VDDQ 0.3 V, grades
f = fMAX = 1/tCYC
–
160
mA
ISB4
Automatic CE Power down
Current – TTL Inputs
Max. VDD, Device Deselected,
VIN  VIH or VIN  VIL, f = 0
All speed
grades
–
135
mA
Capacitance
Parameter [17]
Description
100-pin TQFP 165-ball FBGA Unit
Max
Max
Test Conditions
CIN
Input capacitance
TA = 25 °C, f = 1 MHz,
VDD = 2.5 V, VDDQ = 2.5 V
CCLK
Clock input capacitance
CIO
Input/Output capacitance
6.5
7
pF
3
7
pF
5.5
6
pF
Thermal Resistance
Parameter [17]
Description
JA
Thermal resistance
(junction to ambient)
JC
Thermal resistance
(junction to case)
100-pin TQFP 165-ball FBGA Unit
Package
Package
Test Conditions
Test conditions follow standard test
methods and procedures for measuring
thermal impedance, per EIA/JESD51.
25.21
20.8
°C/W
2.58
3.2
°C/W
AC Test Loads and Waveforms
Figure 4. AC Test Loads and Waveforms
2.5 V I/O Test Load
2.5 V
OUTPUT
R = 1667 
Z0 = 50 
VT = 1.25 V
(a)
5 pF
INCLUDING
JIG AND
SCOPE
ALL INPUT PULSES
VDDQ
OUTPUT
RL = 50 
10%
90%
10%
90%
GND
R = 1538 
(b)
 1ns
 1ns
(c)
Note
17. Tested initially and after any design or process change that may affect these parameters.
Document Number: 001-43804 Rev. *J
Page 20 of 31
CY7C1460SV25
CY7C1462SV25
Switching Characteristics
Over the Operating Range
Parameter [18, 19]
tPower[20]
Description
VCC(typical) to the first access read or write
-250
-167
Unit
Min
Max
Min
Max
1
–
1
–
ms
4.0
–
6.0
–
ns
–
250
–
167
MHz
Clock
tCYC
Clock Cycle Time
FMAX
Maximum Operating Frequency
tCH
Clock HIGH
1.5
–
2.4
–
ns
tCL
Clock LOW
1.5
–
2.4
–
ns
–
2.6
–
3.4
ns
Output Times
tCO
Data Output Valid After CLK Rise
tEOV
OE LOW to Output Valid
tDOH
Data Output Hold After CLK Rise
tCHZ
tCLZ
tEOHZ
tEOLZ
Clock to High Z
[21, 22, 23]
Clock to Low Z
[21, 22, 23]
OE HIGH to Output High Z
OE LOW to Output Low Z
[21, 22, 23]
[21, 22, 23]
–
2.6
–
3.4
ns
1.0
–
1.5
–
ns
–
2.6
–
3.4
ns
1.0
–
1.5
–
ns
–
2.6
–
3.4
ns
0
–
0
–
ns
Setup Times
tAS
Address Setup Before CLK Rise
1.2
–
1.5
–
ns
tDS
Data Input Setup Before CLK Rise
1.2
–
1.5
–
ns
tCENS
CEN Setup Before CLK Rise
1.2
–
1.5
–
ns
tWES
WE, BWx Setup Before CLK Rise
1.2
–
1.5
–
ns
tALS
ADV/LD Setup Before CLK Rise
1.2
–
1.5
–
ns
tCES
Chip Select Setup
1.2
–
1.5
–
ns
tAH
Address Hold After CLK Rise
0.3
–
0.5
–
ns
tDH
Data Input Hold After CLK Rise
0.3
–
0.5
–
ns
tCENH
CEN Hold After CLK Rise
0.3
–
0.5
–
ns
tWEH
WE, BWx Hold After CLK Rise
0.3
–
0.5
–
ns
tALH
ADV/LD Hold after CLK Rise
0.3
–
0.5
–
ns
tCEH
Chip Select Hold After CLK Rise
0.3
–
0.5
–
ns
Hold Times
Notes
18. Timing reference is 1.25 V when VDDQ = 2.5 V.
19. Test conditions shown in (a) of Figure 4 on page 20 unless otherwise noted.
20. This part has a voltage regulator internally; tpower is the time power is supplied above VDD minimum initially, before a Read or Write operation can be initiated.
21. tCHZ, tCLZ, tEOLZ, and tEOHZ are specified with AC test conditions shown in (b) of Figure 4 on page 20. Transition is measured ±200 mV from steady state voltage.
22. At any given voltage and temperature, tEOHZ is less than tEOLZ and tCHZ is less than tCLZ to eliminate bus contention between SRAMs when sharing the same data
bus. These specifications do not imply a bus contention condition, but reflect parameters guaranteed over worst case user conditions. Device is designed to achieve
High Z prior to Low Z under the same system conditions.
23. This parameter is sampled and not 100% tested.
Document Number: 001-43804 Rev. *J
Page 21 of 31
CY7C1460SV25
CY7C1462SV25
Switching Waveforms
Figure 5. Read/Write/Timing [24, 25, 26]
1
2
3
t CYC
4
5
6
A3
A4
7
8
9
A5
A6
A7
10
CLK
tCENS
tCENH
tCL
tCH
CEN
tCES
tCEH
CE
ADV/LD
WE
BWx
A1
ADDRESS
A2
tCO
tAS
tDS
tAH
Data
In-Out (DQ)
tDH
D(A1)
tCLZ
D(A2)
D(A2+1)
tDOH
Q(A3)
tOEV
Q(A4)
tCHZ
Q(A4+1)
D(A5)
Q(A6)
tOEHZ
tDOH
tOELZ
OE
WRITE
D(A1)
WRITE
D(A2)
BURST
WRITE
D(A2+1)
READ
Q(A3)
READ
Q(A4)
BURST
READ
Q(A4+1)
WRITE
D(A5)
READ
Q(A6)
WRITE
D(A7)
DESELECT
Notes
24. For this waveform ZZ is tied low.
25. When CE is LOW, CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH,CE1 is HIGH or CE2 is LOW or CE3 is HIGH.
26. Order of the Burst sequence is determined by the status of the MODE (0 = Linear, 1 = Interleaved). Burst operations are optional.
Document Number: 001-43804 Rev. *J
Page 22 of 31
CY7C1460SV25
CY7C1462SV25
Switching Waveforms (continued)
Figure 6. NOP, STALL and DESELECT Cycles [27, 28, 29]
1
2
A1
A2
3
4
5
A3
A4
6
7
8
9
10
CLK
CEN
CE
ADV/LD
WE
BWx
ADDRESS
A5
tCHZ
D(A1)
Data
Q(A2)
D(A4)
Q(A3)
Q(A5)
In-Out (DQ)
WRITE
D(A1)
READ
Q(A2)
STALL
READ
Q(A3)
WRITE
D(A4)
STALL
DON’T CARE
NOP
READ
Q(A5)
DESELECT
CONTINUE
DESELECT
UNDEFINED
Notes
27. For this waveform ZZ is tied low.
28. When CE is LOW, CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH,CE1 is HIGH or CE2 is LOW or CE3 is HIGH.
29. The IGNORE CLOCK EDGE or STALL cycle (Clock 3) illustrated CEN being used to create a pause. A write is not performed during this cycle.
Document Number: 001-43804 Rev. *J
Page 23 of 31
CY7C1460SV25
CY7C1462SV25
Switching Waveforms (continued)
Figure 7. ZZ Mode Timing [30, 31]
CLK
t ZZ
ZZ
I
t ZZREC
t ZZI
SUPPLY
I DDZZ
t RZZI
ALL INPUTS
(except ZZ)
Outputs (Q)
DESELECT or READ Only
High-Z
DON’T CARE
Notes
30. Device must be deselected when entering ZZ mode. See cycle description table for all possible signal conditions to deselect the device.
31. IOs are in High Z when exiting ZZ sleep mode.
Document Number: 001-43804 Rev. *J
Page 24 of 31
CY7C1460SV25
CY7C1462SV25
Ordering Information
The following table contains only the parts that are currently available. If you do not see what you are looking for, contact your local
sales representative. For more information, visit the Cypress website at www.cypress.com and refer to the product summary page
at http://www.cypress.com/products
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives and distributors. To find the office
closest to you, visit us at http://www.cypress.com/go/datasheet/offices.
Speed
(MHz)
167
Ordering Code
Package
Diagram
CY7C1460SV25-167AXC
51-85050 100-pin TQFP (14 × 20 × 1.4 mm) Pb-free
CY7C1460SV25-167BZC
51-85195 165-ball FBGA (15 × 17 × 1.4 mm)
CY7C1460SV25-167BZXC
250
Part and Package Type
CY7C1460SV25-250BZC
Operating
Range
Commercial
165-ball FBGA (15 × 17 × 1.4 mm) Pb-free
51-85195 165-ball FBGA (15 × 17 × 1.4 mm)
Commercial
Ordering Code Definitions
CY 7
C 146X S V25 - XXX XX X C
Temperature Range:
C = Commercial
Pb-free
Package Type: XX = A or BZ
AX = 100-pin TQFP
BZ = 165-ball FBGA
Frequency Range: XXX = 167 MHz or 250 MHz
V25 = 2.5 V
Die Revision
Part Identifier: 146X = 1460
1460 = PL, 1Mb × 36 (36Mb)
Technology Code: C = CMOS
Marketing Code: 7 = SRAM
Company ID: CY = Cypress
Document Number: 001-43804 Rev. *J
Page 25 of 31
CY7C1460SV25
CY7C1462SV25
Package Diagrams
Figure 8. 100-pin TQFP (14 × 20 × 1.4 mm) A100RA Package Outline, 51-85050
51-85050 *E
Document Number: 001-43804 Rev. *J
Page 26 of 31
CY7C1460SV25
CY7C1462SV25
Package Diagrams (continued)
Figure 9. 165-ball FBGA (15 × 17 × 1.40 mm (0.50 Ball Diameter)) Package Outline, 51-85195
51-85195 *D
Document Number: 001-43804 Rev. *J
Page 27 of 31
CY7C1460SV25
CY7C1462SV25
Acronyms
Document Conventions
Acronym
Description
Units of Measure
BGA
Ball Grid Array
CMOS
Complementary Metal Oxide Semiconductor
°C
degree Celsius
FBGA
Fine-Pitch Ball Grid Array
MHz
megahertz
I/O
Input/Output
µA
microampere
JTAG
Joint Test Action Group
mA
milliampere
LSB
Least Significant Bit
mm
millimeter
ms
millisecond
mV
millivolt
ns
nanosecond
MSB
Most Significant Bit
OE
Output Enable
SRAM
Static Random Access Memory
TAP
Test Access Port
Symbol
Unit of Measure

ohm
%
percent
TCK
Test Clock
pF
picofarad
TMS
Test Mode Select
V
volt
TDI
Test Data-In
W
watt
TDO
Test Data-Out
TQFP
Thin Quad Flat Pack
TTL
Transistor-Transistor Logic
WE
Write Enable
Document Number: 001-43804 Rev. *J
Page 28 of 31
CY7C1460SV25
CY7C1462SV25
Document History Page
Document Title: CY7C1460SV25/CY7C1462SV25, 36-Mbit (1M × 36/2M × 18) Pipelined SRAM with NoBL™ Architecture
Document Number: 001-43804
Rev.
ECN No.
Issue Date
Orig. of
Change
**
1897686
See ECN
VKN /
AESA
*A
2082846
See ECN
VKN
Changed status from Preliminary to Final.
*B
2902562
03/31/2010
VKN
Updated Ordering Information (Updated part numbers).
Updated Package Diagrams.
*C
2958549
06/22/2010
NJY
Updated Ordering Information (Updated part numbers).
*D
3203729
03/23/2011
NJY
Updated Ordering Information (Updated part numbers) and added Ordering
Code Definitions.
Updated Package Diagrams.
Added Acronyms and Units of Measure.
Updated to new template.
*E
3410256
10/18/2011
VIDB
Updated Ordering Information (Removed prune part number
CY7C1462SV25-200AXC).
Updated Package Diagrams.
*F
3572545
04/04/2012
PRIT
Updated Features (Removed CY7C1464SV25 related information, removed
209-ball FBGA package related information).
Updated Functional Description (Removed CY7C1464SV25 related
information).
Removed Logic Block Diagram – CY7C1464SV25.
Updated Pin Configurations (Removed CY7C1464SV25 related information,
removed 165-ball FBGA (15 × 17 × 1.4 mm) pinout for CY7C1462SV25).
Updated Pin Definitions (Removed CY7C1464SV25 related information).
Updated Functional Overview (Removed CY7C1464SV25 related
information).
Updated Truth Table (Removed CY7C1464SV25 related information).
Updated Partial Write Cycle Description (Removed CY7C1464SV25 related
information).
Updated IEEE 1149.1 Serial Boundary Scan (JTAG) (Removed
CY7C1462SV25 and CY7C1464SV25 related information).
Updated Identification Register Definitions (Removed CY7C1462SV25 and
CY7C1464SV25 related information).
Updated Scan Register Sizes (Removed Bit Size (× 18) and Bit Size (× 72)
columns, removed 209-ball FBGA package related information).
Updated Boundary Scan Order (Removed CY7C1462SV25 related
information).
Removed Boundary Scan Order (Corresponding to CY7C1464SV25).
Updated Operating Range (Removed Industrial Temperature Range).
Updated Capacitance (Removed 209-ball FBGA package related information).
Updated Thermal Resistance (Removed 209-ball FBGA package related
information).
Updated Ordering Information.
Updated Package Diagrams (Removed 209-ball FBGA package related
information).
*G
3849207
12/21/2012
PRIT
Updated Ordering Information (Updated part numbers).
*H
3943327
03/25/2013
PRIT
Removed 200 MHz frequency related information in all instances across the
document.
Updated Ordering Information (Removed CY7C1462SV25-200AXC as it is a
pruned part).
Document Number: 001-43804 Rev. *J
Description of Change
New data sheet.
Page 29 of 31
CY7C1460SV25
CY7C1462SV25
Document History Page (continued)
Document Title: CY7C1460SV25/CY7C1462SV25, 36-Mbit (1M × 36/2M × 18) Pipelined SRAM with NoBL™ Architecture
Document Number: 001-43804
Rev.
ECN No.
Issue Date
Orig. of
Change
Description of Change
*I
4953354
10/08/2015
PRIT
Removed 1.8 V I/O related information in all instances across the document.
Removed 1.8 V VDDQ related information in all instances across the document.
Removed 1.8 V TAP AC Test Conditions.
Removed 1.8 V TAP AC Output Load Equivalent.
Updated AC Test Loads and Waveforms:
Removed “3.3 V I/O Test Load”.
Updated Package Diagrams:
spec 51-85050 – Changed revision from *D to *E.
spec 51-85195 – Changed revision from *C to *D.
*J
5211485
04/07/2016
DEVM
Document Number: 001-43804 Rev. *J
Updated to new template.
Completing Sunset Review.
Page 30 of 31
CY7C1460SV25
CY7C1462SV25
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
PSoC®Solutions
Products
ARM® Cortex® Microcontrollers
Automotive
cypress.com/arm
cypress.com/automotive
Clocks & Buffers
Interface
Lighting & Power Control
cypress.com/clocks
PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP
Cypress Developer Community
Forums | Projects | Video | Blogs | Training | Components
cypress.com/interface
cypress.com/powerpsoc
Memory
PSoC
Touch Sensing
USB Controllers
Wireless/RF
cypress.com/memory
Technical Support
cypress.com/support
cypress.com/psoc
cypress.com/touch
cypress.com/usb
cypress.com/wireless
© Cypress Semiconductor Corporation, 2008-2016. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC ("Cypress"). This document,
including any software or firmware included or referenced in this document ("Software"), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries
worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other
intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress
hereby grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to
modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users
(either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress's patents that are infringed by the Software (as
provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation
of the Software is prohibited.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE
OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent
permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any
product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is
the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. Cypress products
are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, life-support devices or
systems, other medical devices or systems (including resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where the failure of the
device or system could cause personal injury, death, or property damage ("Unintended Uses"). A critical component is any component of a device or system whose failure to perform can be reasonably
expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim,
damage, or other liability arising from or related to all Unintended Uses of Cypress products. You shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and other
liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products.
Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in the United
States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners.
Document Number: 001-43804 Rev. *J
Revised April 7, 2016
ZBT is a registered trademark of Integrated Device Technology, Inc. No Bus Latency and NoBL are trademarks of Cypress Semiconductor Corporation.
Page 31 of 31