Product Bulletin Surface Mount Ceramic Chip Capacitors – Low Profile MLCC Outline Drawing L W T TIN PLATE B NICKEL PLATE S ELECTRODES CONDUCTIVE METALLIZATION Dimensions – Millimeters (Inches) EIA Size Code Metric Size Code L Length W Width B Bandwidth S Separation 0805 2012 2.0 (.079) ± 0.2 (.008) 1.25 (.049) ± 0.2 (.008) 0.5 (.02) ± 0.25 (.010) - 1206 3216 3.2 (.126) ± 0.2 (.008) 1.6 (.063) ± 0.2 (.008) 0.5 (.02) ± 0.25 (.010) - See Capacitance Value Table for thickness dimension. Capacitance Values - X5R Dielectric Capacitance Value (μF) KEMET Part Number Voltage 4.7 C0805L475(1)9PAC 10.0 C0805L106(1)9PAC 10.0 C0805L106(1)8PAC 1.0 C1206L105(1)3PAC 4.7 C1206L475(1)4PAC (1) To complete KEMET part number insert K for Capacitance Tolerance Thickness 6.3 ±10%, ±20% 0.85 (.033) ± 0.1 (.004) 6.3 ±10%, ±20% 0.85 (.033) ± 0.1 (.004) 10 ±10%, ±20% 0.85 (.033) ± 0.1 (.004) 25 ±10%, ±20% 0.78 (.031) ± 0.1 (.004) 16 ±10%, ±20% 0.90 (.035) ± 0.1(.004) ±10% or M for ±20% capacitance tolerance. Qty 7" Reel 4,000 4,000 4,000 4,000 4,000 Capacitance Values - X7R Dielectric Capacitance Value (μF) 1.0 KEMET Part Number Voltage Capacitance Tolerance Thickness Qty 7" Reel C0805L105(1)8RAC 10 ±10%, ±20% 0.78 (.031) ± 0.1 (.004) 4,000 (1) To complete KEMET part number insert K for ±10% or M for ±20% capacitance tolerance. F9078C 08/07 Capacitor Ordering Information C 0805 L 475 K 9 P A End Metallization C = Standard (Tin-plate nickel barrier) Style C - Ceramic Size Code See dimension table Specification L - Low Profile Ceramic Chip Capacitance Code, pF First two digits represent significant figures. Third digit specifies number of zeros. 100 pF = 101. (Use “9” for 1.0 through 9.9 pF) (Use “8” for 0.1 through .99 pF) Capacitance Tolerance K = ± 10% M = ±20% C Failure Rate Level A = Not Applicable Temperature Characteristic Designated by Capacitance Change Over Temperature Range R = X7R (±15%) (-55°C +125°C) P = X5R (±15%) (-55°C +85°C) 9 = 6.3V 3 = 25V 8 = 10V Voltage 4 = 16V Electrical Parameters - X5R Dielectric As detailed in the KEMET Surface Mount Catalog F3102 for X5R, with following specific requirements based on room temperature (25°C) parameters: • Operating Range: -55°C to +85°C, with no-bias capacitance shift limited to ± 15% over that range. • Insulation Resistance (IR) measured after 2 minutes at rated voltage @ 25°C: Limit is 500 megohm microfarads or 10000MΩ, whichever is less. • Capacitance and Dissipation Factor (DF) measured at the following conditions. DF Limit is 10%. 1 kHz and 1 Vrms. Electrical Parameters - X7R Dielectric As detailed in the KEMET Surface Mount Catalog F3102 for X7R, with following specific requirements based on room temperature (25°C) parameters: • Operating Range: -55°C to +125°C, with no-bias capacitance shift limited to ± 15% over that range. • Insulation Resistance (IR) measured after 2 minutes at rated voltage @ 25°C: Limit is 500 megohm microfarads or 10000MΩ, whichever is less. • Capacitance and Dissipation Factor (DF) measured at the following conditions. DF Limit is 5%. 1 kHz and 1 Vrms. Soldering Process These components are suitable for reflow only. All parts incorporate the standard KEMET barrier layer of pure nickel, with an overplate of pure tin to provide excellent solderability as well as resistance to leaching. Marking These chips will be supplied unmarked. In general, the information in the KEMET Surface Mount catalog F3102 applies to these capacitors. The information in this bulletin supplements that in the catalog. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com