TI bq24196RGER

bq24196
www.ti.com
SLUSB98 – OCTOBER 2012
I2C Controlled 2.5A Single Cell USB/Adapter Charger
With Narrow VDC Power Path Management and USB OTG
Check for Samples: bq24196
FEATURES
1
•
2
•
•
•
•
•
•
•
High Efficiency 2.5A Switch Mode Charger
– 92% Charge Efficiency at 2A
Highest Battery Discharge Efficiency with
12mΩ Battery Discharge MOSFET up to 9A
Discharge Current
Single Input USB-compliant/Adapter Charger
– Input Voltage and Current Limit Supports
USB2.0 and USB 3.0
– Input Current Limit: 100mA, 150mA, 500mA,
900mA, 1.2A, 1.5A, 2A and 3A
3.9V–17V Input Operating Voltage Range
– Support All Kinds of Adapter with Input
Voltage DPM Regulation
USB OTG 5V at 1.3A Synchronous Boost
Converter Operation
– 93% 5V Boost Efficiency at 1A
Narrow VDC (NVDC) Power Path Management
– Instant-on Works with No Battery or Deeply
Discharged Battery
– Ideal Diode Operation in Battery
Supplement Mode
1.5MHz Switching Frequency for Low Profile
Inductor
Autonomous Battery Charging with or without
Host Management
– Battery Charge Enable
– Battery Charge Preconditioning
– Charge Termination and Recharge
•
•
•
•
•
•
High Accuracy (0°C to 125°C)
– ±0.5% Charge Voltage Regulation
– ±7% Charge Current Regulation
– ±7.5% Input Current Regulation
– ±2% Output Regulation in Boost Mode
High Integration
– Power Path Management
– Synchronous Switching MOSFETs
– Integrated Current Sensing
– Bootstrap Diode
– Internal Loop Compensation
Safety
– Battery Temperature Sensing and Charging
Safety Timer
– Thermal Regulation and Thermal Shutdown
– Input System Over-Voltage Protection
– MOSFET Over-Current Protection
Charge Status Outputs for LED or Host
Processor
Low Battery Leakage Current and Support
Shipping Mode
4mm x 4mm QFN-24 Package
APPLICATIONS
•
•
•
•
•
Tablet PC
Smart Phone
Portable Audio Speaker
Portable Media Players
Internet Devices
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PowerPAD is a trademark of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2012, Texas Instruments Incorporated
bq24196
SLUSB98 – OCTOBER 2012
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
DESCRIPTION
The bq24196 is highly-integrated switch-mode battery charge management and system power path management
devices for single cell Li-Ion and Li-polymer battery in a wide range of tablet and other portable devices. Its low
impedance power path optimizes switch-mode operation efficiency, reduces battery charging time and extends
battery life during discharging phase. The I2C serial interface with charging and system settings makes the
device a truly flexible solution.
The device supports a wide range of input sources, including standard USB host port, USB charging port and
high power DC adapter. The bq24196 takes the result from detection circuit in the system, such as USB PHY
device. The bq24196 is compliant with USB 2.0 and USB 3.0 power spec with input current and voltage
regulation. Meanwhile, the bq24196 meets USB On-the-Go operation power rating specification by supplying 5V
on VBUS with current limit up to 1.3A
The power path management regulates the system slightly above battery voltage but does not drop below 3.5V
minimum system voltage (programmable). With this feature, the system maintains operation even when the
battery is completely depleted or removed. When the input current limit or voltage limit is reached, the power
path management automatically reduces the charge current to zero. As the system load continues to increase,
the power path discharges the battery until the system power requirement is met. This supplement mode
operation prevents overloading the input source.
The device initiates and completes a charging cycle without software control. It automatically detects the battery
voltage and charges the battery in three phases: pre-conditioning, constant current and constant voltage. At the
end of the charging cycle, the charger automatically terminates when the charge current is below a preset limit in
the constant voltage phase. When the full battery falls below the recharge threshold, the charger will
automatically start another charging cycle.
The device provides various safety features for battery charging and system operation, including negative
thermistor monitoring, charging safety timer and over-voltage/over-current protections. The thermal regulation
reduces charge current when the junction temperature exceeds 120°C (programmable).
The STAT output reports the charging status and any fault conditions. The PG output in the bq24196 indicates if
a good power source is present. The INT immediately notifies the host when a fault occurs.
The bq24196 are available in a 24-pin, 4x4 mm2 thin QFN package.
ORDERING INFORMATION
2
PART NUMBER
PART MARKING
PACKAGE
bq24196
bq24196
24-pin 4mmx4mm VQFN
Submit Documentation Feedback
ORDERING NUMBER
QUANTITY
bq24196RGER
3000
bq24196RGET
250
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
bq24196
www.ti.com
SLUSB98 – OCTOBER 2012
APPLICATION DIAGRAM
bq24196
5V USB
SDP/DCP
VBUS
PMID
1μF
1μH
SYS: 3.5V-4.45V
SW
10μF
47nF
6.8μF
10μF
10μF
10μF
BOOT
REGN
1μF
SYS
PGND
2.2kW
SYS
PG
STAT
VREF
10kW
10kW
BAT
10μF
353W
(1.5A max)
10kW
SDA
SCL
INT
OTG
CE
Host
PHY
ILIM
REGN
5.52kW
TS1
TS2
31.23kW
PSEL
Power Pad
10kW
(103-AT)
Figure 1. bq24196 with PSEL from PHY, charging from SDP/DCP, and Two Thermistor Connections
bq24196
5V USB
15V Adapter
SYS: 3.5V-4.35V
SW
VBUS
PMID
1μF
2.2μH
47nF
6.8μF
10μF
10μF
BOOT
REGN
4.7μF
SYS
PGND
2.2kW
PG
STAT
VREF
10kW
10kW
Host
PHY
SYS
BAT
10kW
SDA
SCL
INT
OTG
CE
ILIM
10μF
353W
(1.5A max)
REGN
5.52kW
TS1
TS2
PSEL
Power Pad
31.23kW
10kW
(103-AT)
Figure 2. bq24196 with PSEL, USB On-The-Go (OTG), and Single Thermistor Connection
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
3
bq24196
SLUSB98 – OCTOBER 2012
www.ti.com
FUNCTIONAL BLOCK DIAGRAM
VBUS
PMID
Q1
3.8V
UVLO
Q1 Gate
Control
VBATz +80mV
SLEEP
REGN
REGN
LDO
EN_HIZ
ACOV
18V
BTST
FBO
VBUS
VBUS_OVP_BOOST
5.4V
I(Q2)
VINDPM
Q2_UCP_BOOST
100mA
I(Q3)
SW
Q3_OCP_BOOST
3.2A
IINDPM
BAT
IC TJ
CONVERTER
CONTROL
BATOVP
Q2
REGN
104%xVBAT_REG
BAT
TREG
VBAT_REG
100mA
UCP
Q2_OCP
I(Q3)
SYS
Q3
PGND
7A
VSYSMIN
ICHG_REG
I(Q2)
EN_HIZ
EN_CHARGE
EN_BOOST
REFRESH
V(BTST-SW)
4.2V
SYS
ICHG
VBAT_REG
ICHG_REG
REF
DAC
BAD_SRC
CONVERTER
CONTROL
TSHUT
STATE
MACHINE
ILIM
PSEL
USB
Adapter
1.5A
BAT_GD
RECHRG
INT
I2C
Interface
SCL
4
BAT
BAT
SDA
BATSHORT
bq24196
4.1V
BAT
ICHG
TERMINATION
CHARGE
ITERM
CONTROL
SUSPEND
STATE
2.8V
MACHINE BATLOWV
BAT
STAT
Q4
IC TJ
TSHUT
3.6V
OTG
PG
30mA
IDC
Q4 Gate
Control
TS1
BATTERY
THERMISTER
SENSING
TS2
2V
BAT
CE
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
bq24196
www.ti.com
SLUSB98 – OCTOBER 2012
VBUS
PMID
REGN
BTST
SW
SW
PINOUTS
24
23
22
21
20
19
VBUS
1
18
PGND
PSEL
2
17
PGND
16
SYS
PG
3
bq24196
5
14
BAT
SDA
6
13
BAT
INT
7
8
9
10
11
12
TS2
SCL
TS1
SYS
ILIM
15
CE
4
OTG
STAT
PIN FUNCTIONS
PIN
TYPE
DESCRIPTION
1,24
P
Charger Input Voltage. The internal n-channel reverse block MOSFET (RBFET) is connected between VBUS and PMID
with VBUS on source. Place a 1µF ceramic capacitor from VBUS to PGND and place it as close as possible to IC. (Refer
to Application Information Section for details)
PSEL
–
I
Digital
Power source selection input. High indicates a USB host source and Low indicates an adapter source.
PG
–
O
Digital
Open drain active low power good indicator. Connect to the pull up rail via 10kohm resistor. LOW indicates a good input
source if the input voltage is between UVLO and ACOV, above SLEEP mode threshold, and current limit is above 30mA.
STAT
4
O
Digital
Open drain charge status output to indicate various charger operation. Connect to the pull up rail via 10kohm. LOW
indicates charge in progress. HIGH indicates charge complete or charge disabled. When any fault condition occurs, STAT
pin blinks at 1Hz.
SCL
5
I
Digital
I2C Interface clock. Connect SCL to the logic rail through a 10kΩ resistor.
SDA
6
I/O
Digital
I2C Interface data. Connect SDA to the logic rail through a 10kΩ resistor.
INT
7
O
Digital
Open-drain Interrupt Output. Connect the INT to a logic rail via 10kΩ resistor. The INT pin sends active low, 256us pulse
to host to report charger device status and fault.
OTG
8
I
Digital
USB current limit selection pin during buck mode, and active high enable pin during boost mode.
NAME
NO.
VBUS
In buck mode with USB host (PSEL=High), when OTG = High, IIN limit = 500mA and when OTG = Low, IIN limit =
100mA.
The boost mode is activated when the REG01[5:4]=10 and OTG pin is High.
CE
9
I
Digital
Active low Charge Enable pin. Battery charging is enabled when REG01[5:4]=01 and CE pin = Low. CE pin must be
pulled high or low.
ILIM
10
I
Analog
ILIM pin sets the maximum input current limit by regulating the ILIM voltage at 1V. A resistor is connected from ILIM pin to
ground to set the maximum limit as IINMAX = (1V/RILIM) × 530. The actual input current limit is the lower one set by ILIM
and by I2C REG00[2:0]. The minimum input current programmed on ILIM pin is 500mA.
TS1
11
I
Analog
Temperature qualification voltage input #1. Connect a negative temperature coefficient thermistor. Program temperature
window with a resistor divider from REGN to TS1 to GND. Charge suspends when either TS pin is out of range.
Recommend 103AT-2 thermistor.
TS2
12
I
Analog
Temperature qualification voltage input #2. Connect a negative temperature coefficient thermistor. Program temperature
window with a resistor divider from REGN to TS2 to GND. Charge suspends when either TS pin is out of range.
Recommend 103AT-2 thermistor. TS1 and TS2 pin can be connected together for single thermistor application.
BAT
13,14
P
Battery connection point to the positive terminal of the battery pack. The internal BATFET is connected between BAT and
SYS. Connect a 10uF closely to the BAT pin.
SYS
15,16
P
System connection point. The internal BATFET is connected between BAT and SYS. When the battery falls below the
minimum system voltage, switch-mode converter keeps SYS above the minimum system voltage. (Refer to Application
Information Section for inductor and capacitor selection)
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
5
bq24196
SLUSB98 – OCTOBER 2012
www.ti.com
PIN FUNCTIONS (continued)
PIN
TYPE
DESCRIPTION
NAME
NO.
PGND
17,18
P
SW
19,20
O
Analog
Switching node connecting to output inductor. Internally SW is connected to the source of the n-channel HSFET and the
drain of the n-channel LSFET. Connect the 0.047µF bootstrap capacitor from SW to BTST.
BTST
21
P
PWM high side driver positive supply. Internally, the BTST is connected to the anode of the boost-strap diode. Connect
the 0.047µF bootstrap capacitor from SW to BTST.
REGN
22
P
PWM low side driver positive supply output. Internally, REGN is connected to the cathode of the boost-strap diode. For
VBUS above 6V, connect 1-µF ceramic capacitor from REGN to analog GND. For VBUS below 6V, connect a 4.7-μF
(10V rating) ceramic capacitor from REGN to analog GND. The capacitor should be placed close to the IC. REGN also
serves as bias rail of TS1 and TS2 pins.
PMID
23
O
Analog
PowerPAD
–
P
Power ground connection for high-current power converter node. Internally, PGND is connected to the source of the nchannel LSFET. On PCB layout, connect directly to ground connection of input and output capacitors of the charger. A
single point connection is recommended between power PGND and the analog GND near the IC PGND pin.
Connected to the drain of the reverse blocking MOSFET and the drain of HSFET. Given the total input capacitance,
connect a 1-µF capacitor on VBUS to PGND, and the rest all on PMID to PGND. (Refer to Application Information Section
for details)
Exposed pad beneath the IC for heat dissipation. Always solder PowerPAD™ to the board, and have vias on the Power
Pad plane star-connecting to PGND and ground plane for high-current power converter.
ABSOLUTE MAXIMUM RATINGS
VALUE
VBUS
Voltage range (with respect to GND)
Output sink current
–2 V – 20 V
PMID, STAT, PG
–0.3 V –20 V
BTST
–0.3 V – 26 V
SW
–2 V – 20 V
BAT, SYS (converter not switching)
–0.3 V – 6 V
SDA, SCL, INT, OTG, ILIM, REGN, TS1, TS2, CE, PSEL
–0.3 V – 7 V
BTST TO SW
–0.3 V – 7 V
PGND to GND
–0.3 V – 0.3 V
INT, STAT, PG
6mA
Junction temperature
–40°C to 150°C
Storage temperature
–65°C to 150°C
RECOMMENDED OPERATING CONDITIONS
MIN
VIN
Input voltage
IIN
Input current
ISYS
VBAT
IBAT
TA
(1)
6
3.9
MAX
17
UNIT
(1)
V
3
A
Output current (SYS)
2.5
A
Battery voltage
4.4
V
Fast charging current
2.5
A
6 (continuous)
9 (peak)
(up to 1 sec duration)
A
85
°C
Discharging current with internal MOSFET
Operating free-air temperature range
–40
The inherent switching noise voltage spikes should not exceed the absolute maximum rating on either the BTST or SW pins. A tight
layout minimizes switching noise.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
bq24196
www.ti.com
SLUSB98 – OCTOBER 2012
THERMAL INFORMATION
RGE PACKAGE
THERMAL METRIC (1)
24-PIN
θJA
Junction-to-ambient thermal resistance
32.2
θJCtop
Junction-to-case (top) thermal resistance
29.8
θJB
Junction-to-board thermal resistance
9.1
ψJT
Junction-to-top characterization parameter
0.3
ψJB
Junction-to-board characterization parameter
9.1
θJCbot
Junction-to-case (bottom) thermal resistance
2.2
UNITS
°C/W
space
(1)
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
ELECTRICAL CHARACTERISTICS
VVBUS_UVLOZ < VVBUS < VACOV and VVBUS > VBAT + VSLEEP, TJ = –40°C to 125°C and TJ = 25°C for typical values unless other
noted.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
QUIESCENT CURRENTS
VVBUS < VUVLO, VBAT = 4.2 V, leakage between
BAT and VBUS
IBAT
IVBUS
IOTGBOOST
Battery discharge current (BAT, SW, SYS)
Input supply current (VBUS)
Battery Discharge Current in boost mode
5
µA
High-Z Mode, or no VBUS, BATFET disabled
(REG07[5] = 1)
12
20
µA
High-Z Mode, or no VBUS, REG07[5] = 0, –40°C –
85°C
32
55
µA
VVBUS = 5 V, High-Z mode
15
30
µA
VVBUS = 17 V, High-Z mode
30
50
µA
VVBUS > VUVLO, VVBUS > VBAT, converter not
switching
1.5
3
mA
VVBUS > VUVLO, VVBUS > VBAT, converter switching,
VBAT=3.2V, ISYS=0A
4
mA
VVBUS > VUVLO, VVBUS > VBAT, converter switching,
VBAT=3.8V, ISYS=0A
15
mA
4
mA
VBAT=4.2V, Boost mode, IVBUS = 0A, converter
switching
VBUS/BAT POWER UP
VVBUS_OP
VBUS operating range
VVBUS_UVLOZ
VBUS for active I2C, no battery
VVBUS rising
3.9
3.6
17
V
VSLEEP
Sleep mode falling threshold
VVBUS falling, VVBUS-VBAT
35
80
120
mV
VSLEEPZ
Sleep mode rising threshold
VVBUS rising, VVBUS-VBAT
VACOV
VBUS over-voltage rising threshold
VVBUS rising
170
250
300
mV
17.4
18
VACOV_HYST
VBUS Over-Voltage Falling Hysteresis
VVBUS falling
V
700
mV
VBAT_UVLOZ
Battery for active I2C, no VBUS
VBAT rising
VBAT_DPL
Battery depletion threshold
VBAT falling
2.4
2.6
V
VBAT_DPL_HY
Battery depletion rising hysteresis
VBAT rising
170
230
mV
VVBUSMIN
Bad adapter detection threshold
VVBUS falling
3.8
V
IBADSRC
Bad adapter detection current source
30
mA
tBADSRC
Bad source detection duration
30
ms
V
2.3
V
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
7
bq24196
SLUSB98 – OCTOBER 2012
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
VVBUS_UVLOZ < VVBUS < VACOV and VVBUS > VBAT + VSLEEP, TJ = –40°C to 125°C and TJ = 25°C for typical values unless other
noted.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
4.35
V
POWER PATH MANAGEMENT
VSYS_RANGE
System regulation voltage
Isys = 0A, Q4 off, VBAT up to 4.2 V,
REG01[3:1]=101, VSYSMIN = 3.5 V
3.5
VSYS_MIN
System voltage output
REG01[3:1]=101, VSYSMIN = 3.5 V
3.55
RON(RBFET)
Internal top reverse blocking MOSFET onresistance
Measured between VBUS and PMID
23
38
RON(HSFET)
Internal top switching MOSFET onresistance between PMID and SW
TJ = –40°C – 85°C
30
38
TJ = -40°C – 125°C
30
48
RON(LSFET)
Internal bottom switching MOSFET onresistance between SW and PGND
TJ = –40°C – 85°C
35
48
TJ = -40°C – 125°C
35
51
VFWD
BATFET forward voltage in supplement
mode
BAT discharge current 10mA
30
VSYS_BAT
SYS/BAT Comparator
VSYS falling
VBATGD
Battery good comparator rising threshold
VBAT rising
VBATGD_HYST
Battery good comparator falling threshold
VBAT falling
3.65
V
3.55
mΩ
mΩ
mV
90
3.4
mΩ
mV
3.7
100
V
mV
BATTERY CHARGER
VBAT_REG_ACC
Charge voltage regulation accuracy
VBAT = 4.208V
–0.5%
0.5%
VBAT = 3.8V, ICHG = 1792mA, TJ = 25°C
–4%
4%
VBAT = 3.8V, ICHG = 1792mA, TJ = –20°C – 125°C
–7%
IICHG_REG_ACC
Fast charge current regulation accuracy
ICHG_20pct
Charge current with 20% option on
VBAT = 3.1V, ICHG = 104mA, REG02=03
75
100
125
mA
VBATLOWV
Battery LOWV falling threshold
Fast charge to precharge, REG04[1] = 1
2.6
2.8
2.9
V
VBATLOWV_HYST
Battery LOWV rising threshold
Precharge to fast charge, REG04[1] = 1
2.8
3.0
3.1
V
IPRECHG_ACC
Precharge current regulation accuracy
VBAT = 2.6V, ICHG = 256mA
–20%
ITERM_ACC
Termination current accuracy
ITERM = 256mA, ICHG = 960mA
–20%
VSHORT
Battery Short Voltage
VBAT falling
1.8
V
VSHORT_HYST
Battery Short Voltage hysteresis
VBAT rising
200
mV
ISHORT
Battery short current
VBAT<2.2V
100
mA
VRECHG
Recharge threshold below VBAT_REG
VBAT falling, REG04[0] = 0
100
mV
tRECHG
Recharge deglitch time
VBAT falling, REG04[0]=0
20
TJ = 25°C
12
15
TJ = –40°C – 125°C
12
20
RON_BATFET
SYS-BAT MOSFET on-resistance
7%
20%
20%
ms
mΩ
INPUT VOLTAGE/CURRENT REGULATION
VINDPM_REG_ACC
Input voltage regulation accuracy
USB Input current regulation limit, VBUS =
5V, current pulled from SW
IUSB_DPM
–2%
2%
USB100
85
100
mA
USB150
125
150
mA
USB500
440
500
mA
USB900
750
900
mA
1.4
1.6
A
530
AxΩ
IADPT_DPM
Input current regulation accuracy
Input current limit 1.5A
IIN_START
Input current limit during system start up
VSYS<2.2V
KILIM
IIN = KILIM/RILIM
IINDPM = 1.5A
1.5
100
440
485
mA
BAT OVER-VOLTAGE PROTECTION
VBATOVP
Battery over-voltage threshold
VBAT rising, as percentage of VBAT_REG
104%
VBATOVP_HYST
Battery over-voltage hysteresis
VBAT falling, as percentage of VBAT_REG
2%
tBATOVP
Battery over-voltage deglitch time to disable
charge
1
µs
THERMAL REGULATION AND THERMAL SHUTDOWN
TJunction_REG
Junction temperature regulation accuracy
REG06[1:0] = 11
TSHUT
Thermal shutdown rising temperature
Temperature increasing
TSHUT_HYS
Thermal shutdown hysteresis
8
115
120
160
125
°C
°C
30
°C
Thermal shutdown rising deglitch
Temperature increasing delay
1
ms
Thermal shutdown falling deglitch
Temperature decreasing delay
1
ms
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
bq24196
www.ti.com
SLUSB98 – OCTOBER 2012
ELECTRICAL CHARACTERISTICS (continued)
VVBUS_UVLOZ < VVBUS < VACOV and VVBUS > VBAT + VSLEEP, TJ = –40°C to 125°C and TJ = 25°C for typical values unless other
noted.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
COLD/HOT THERMISTER COMPARATOR
VLTF
Cold temperature threshold, TS pin voltage
rising threshold
Charger suspends charge. As Percentage to VREGN
73%
73.5%
74%
VLTF_HYS
Cold temperature hysteresis, TS pin voltage
falling
As Percentage to VREGN
0.2%
0.4%
0.6%
VHTF
Hot temperature TS pin voltage falling
threshold
As Percentage to VREGN
46.6%
47.2%
48.8%
VTCO
Cut-off temperature TS pin voltage falling
threshold
As Percentage to VREGN
44.2%
44.7%
45.2%
Deglitch time for temperature out of range
detection
VTS > VLTF, or VTS < VTCO, or VTS < VHTF
10
ms
7
A
CHARGE OVER-CURRENT COMPARATOR
IHSFET_OCP
HSFET over-Current threshold
IBATFET_OCP
System over load threshold
5.3
9
A
CHARGE UNDER-CURRENT COMPARATOR (CYCLE-BY-CYCLE)
VLSFET_UCP
LSFET charge under-current falling
threshold
From sync mode to non-sync mode
100
mA
PWM OPERATION
FSW
PWM Switching frequency, and digital clock
DMAX
Maximum PWM duty cycle
VBTST_REFRESH
Bootstrap refresh comparator threshold
1300
1500
1700
kHz
97%
VBTST-VSW when LSFET refresh pulse is
requested, VBUS=5V
3.6
VBTST-VSW when LSFET refresh pulse is
requested, VBUS>6V
4.2
V
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
9
bq24196
SLUSB98 – OCTOBER 2012
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
VVBUS_UVLOZ < VVBUS < VACOV and VVBUS > VBAT + VSLEEP, TJ = –40°C to 125°C and TJ = 25°C for typical values unless other
noted.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
BOOST MODE OPERATION
VOTG_REG
OTG output voltage
I(VBUS) = 0
VOTG_REG_ACC
OTG output voltage accuracy
I(VBUS) = 0
IOTG
OTG mode output current
VOTG_OVP
OTG over-voltage threshold
VOTG_ILIM
LSFET cycle-by-cycle current limit
VOTG_HSZCP
HSFET under current falling threshold
IRBFET_OCP
RBFET over-current threshold
5.00
–2%
REG01[0] = 0
0.5
REG01[0] = 1
1.3
A
A
5.3
3.2
V
2%
5.5
V
4.6
A
100
mA
REG01[0] = 1
1.4
1.8
2.7
REG01[0] = 0
0.6
1.1
1.8
A
REGN LDO
VREGN
REGN LDO output voltage
IREGN
REGN LDO current limit
VVBUS = 10V, IREGN = 40mA
5.6
6
6.4
VVBUS = 5V, IREGN = 20mA
4.75
4.8
4.85
VVBUS = 10V, VREGN = 3.8V
50
V
V
mA
LOGIC I/O PIN CHARACTERISTICS (OTG, CE, PSEL, STAT, PG)
VILO
Input low threshold
VIH
Input high threshold
0.4
VOUT_LO
Output low saturation voltage
Sink current = 5 mA
IBIAS
High level leakage current
Pull up rail 1.8V
1.3
V
V
0.4
V
1
µA
I2C INTERFACE (SDA, SCL, INT)
VIH
Input high threshold level
VPULL-UP = 1.8V, SDA and SCL
VIL
Input low threshold level
VPULL-UP = 1.8V, SDA and SCL
1.3
0.4
V
VOL
Output low threshold level
Sink current = 5mA
0.4
V
IBIAS
High-level leakage current
VPULL-UP = 1.8V, SDA and SCL
1
µA
fSCL
SCL clock frequency
400
kHz
V
DIGITAL CLOCK AND WATCHDOG TIMER
fHIZ
Digital crude clock
REGN LDO disabled
15
35
50
kHz
fDIG
Digital clock
REGN LDO enabled
1300
1500
1700
kHz
tWDT
REG05[5:4]=11
REGN LDO enabled
136
160
sec
TYPICAL CHARACTERISTICS
Table 1. Tables of Figures
FIGURE NO.
CHARGING EFFICIENCY vs. CHARGING CURRENT
Figure 3
SYSTEM LIGHT LOAD EFFICIENCY vs SYSTEM LOAD CURRENT
Figure 4
BOOST MODE EFFICIENCY vs VBUS LOAD CURRENT
Figure 5
SYS VOLTAGE REGULATION vs SYSTEM LOAD
Figure 6
BOOST MODE VBUS VOLTAGE REGULATION vs VBUS LOAD CURRENT
Figure 7
SYS VOLTAGE vs TEMPERATURE
Figure 8
BAT VOLTAGE vs TEMPERATURE
Figure 9
INPUT CURRENT LIMIT vs TEMPERATURE
Figure 10
CHARGE CURRENT vs TEMPERATURE
Figure 11
Power Up with Charge Disabled (VBAT 3.2V)
Figure 12
Power Up with Charge Enabled
Figure 13
Charge Enable (VBUS 5V)
Figure 14
Charge Disable (VBUS 12V)
Figure 15
Input Current DPM Response without Battery (VBUS 5V, IIN 3A, Charge Disable)
Figure 16
Load Transient during Supplement Mode (VBUS 9V, IIN 1.5A, VBAT 3.8V)
Figure 17
10
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
bq24196
www.ti.com
SLUSB98 – OCTOBER 2012
TYPICAL CHARACTERISTICS (continued)
Table 1. Tables of Figures (continued)
FIGURE NO.
PWM Switching Waveform (VBUS 12V, VBAT 3.8V, ICHG 1.5A)
Figure 18
PFM Switching Waveform (VBUS 9V, No Battery, ISYS 10 mA, Charge Disable)
Figure 19
Boost Mode Switching Waveform (VBAT 3.8V, ILOAD 1A)
Figure 20
Boost Mode Load Transient (VBAT 3.8V)
Figure 21
SYSTEM LIGHT LOAD EFFICIENCY
vs
SYSTEM LOAD CURRENT
95
95
93
90
Efficiency (%)
Efficiency (%)
CHARGING EFFICIENCY
vs
CHARGING CURRENT
91
89
VBUS = 5 V
VBUS = 7 V
VBUS = 9 V
VBUS = 12 V
87
85
0
0.5
1
1.5
2
Load Current (A)
100
2.5
85
80
75
VBUS = 5 V
VBUS = 9 V
70
0
3
100
200
300
400
500
Load Current (mA)
C020
600
C012
Figure 3.
Figure 4.
BOOST MODE EFFICIENCY
vs
VBUS LOAD CURRENT
SYS VOLTAGE REGULATION
vs
SYSTEM LOAD
3.70
VBAT = 3.2 V
VBAT = 3.8 V
3.68
SYS Voltage (V)
Efficiency (%)
95
90
85
3.66
3.64
3.62
VBUS = 5 V
VBUS = 17 V
3.60
80
0
500
1000
VBUS Load Current (A)
1500
0
C013
Figure 5.
1
2
3
4
System Load Current (A)
5
C014
Figure 6.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
11
bq24196
SLUSB98 – OCTOBER 2012
www.ti.com
BOOST MODE VBUS VOLTAGE REGULATION
vs
VBUS LOAD CURRENT
SYS VOLTAGE
vs
TEMPERATURE
5.04
3.80
5.02
3.75
5.00
SYS Voltage (V)
VBUS Voltage (V)
SYSMIN 3.5 V
4.98
4.96
4.94
3.70
3.65
3.60
VBAT = 3.2 V
4.92
3.55
VBAT = 3.8 V
VBAT = 4.2 V
4.90
0
200
400
3.50
600
800
1000
1200
±50
1400
VBUS Load Current (A)
0
50
100
Temperature (ƒC)
C005
Figure 7.
Figure 8.
BAT VOLTAGE
vs
TEMPERATURE
INPUT CURRENT LIMIT
vs
TEMPERATURE
4.25
150
C001
2000
1800
Input Current Limit (A)
BAT Voltage (V)
4.21
4.17
4.13
4.09
1600
1400
1200
1000
IIN = 500 mA
800
IIN = 1.5 A
600
IIN = 2 A
VREG = 4.112 V
VREG = 4.208 V
4.05
400
±50
0
50
100
±50
150
Temperture (ƒC)
0
50
100
Temperature (ƒC)
C002
Figure 9.
Figure 10.
CHARGE CURRENT
vs
TEMPERATURE
Power Up with Charge Disabled (VBAT 3.2V)
150
C003
5
4.5
Charge Current (A)
4
VBUS
5V/div
3.5
3
REGN
5V/div
2.5
2
SYS
2V/div
1.5
1
/PG
2V/div
TREG 80 C
TREG 120 C
0.5
0
40
50
60
70
80
90
100
Temperture (ƒC)
110
120
130
Figure 11.
12
40ms/div
C009
Figure 12.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
bq24196
www.ti.com
SLUSB98 – OCTOBER 2012
Power Up with Charge Enabled
Charge Enable (VBUS 5V)
STAT
2V/div
VBUS
5V/div
/CE
5V/div
REGN
5V/div
SW
5V/div
SYS
2V/div
IBAT
1A/div
IBAT
2A/div
100ms/div
400us/div
Figure 13.
Figure 14.
Charge Disable (VBUS 12V)
Input Current DPM Response without Battery
(VBUS 5V, IIN 3A, Charge Disable)
SYS
3.4V Offset
200mV/div
STAT
2V/div
/CE
5V/div
IIN
2A/div
SW
10V/div
ISYS
2A/div
IBAT
1A/div
2ms/div
4us/div
Figure 15.
Figure 16.
Load Transient during Supplement Mode
(VBUS 9V, IIN 1.5A, VBAT 3.8V)
PWM Switching Waveform
(VBUS 12V, VBAT 3.8V, ICHG 1.5A)
SYS
3.4V offset
200mV/div
STAT
2V/div
ISYS
5A/div
/CE
5V/div
IIN
1A/div
SW
10V/div
IBAT
2A/div
IBAT
1A/div
2ms/div
4us/div
Figure 17.
Figure 18.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
13
bq24196
SLUSB98 – OCTOBER 2012
www.ti.com
PFM Switching Waveform
(VBUS 9V, No Battery, ISYS 10 mA, Charge Disable)
Boost Mode Switching Waveform
(VBAT 3.8V, ILOAD 1A)
SYS
3.4V offset
100mV/div
SW
5V/div
SW
5V/div
IL
1A/div
IL
1A/div
4us/div
400ns/div
Figure 19.
Figure 20.
Boost Mode Load Transient(VBAT 3.8V)
VBUS
5V offset
200mV/div
IBAT
500mA/div
IVBUS
500mA/div
4ms/div
Figure 21.
14
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
bq24196
www.ti.com
SLUSB98 – OCTOBER 2012
I2C Registers
Address: 6BH. REG00-07 support Read and Write. REG08-0A are read only.
Input Source Control Register REG00 (default 00110000, or 30)
BIT
DESCRIPTION
Bit 7
EN_HIZ
0 – Disable, 1 – Enable
Input Voltage Limit
Bit 6
VINDPM[3]
640mV
Bit 5
VINDPM[2]
320mV
Bit 4
VINDPM[1]
160mV
Bit 3
VINDPM[0]
80mV
Input Current Limit (Actual input current limit is the lower of I2C and ILIM)
Bit 2
IINLIM[2]
000 – 100mA, 001 – 150mA, 010 – 500mA,
011 – 900mA, 100 – 1.2A, 101 – 1.5A,
Bit 1
IINLIM[1]
110 – 2A, 111 – 3A
Bit 0
IINLIM[0]
Default: Disable (0)
Offset 3.88V, Range: 3.88V-5.08V
Default: 4.36V (0110)
Default SDP: 100mA (000)(OTG pin=0) or 500mA (010)
(OTG pin=1)
Default DCP/CDP: 3A (111)
Power-On Configuration Register REG01 (default 00011011, or 1B)
BIT
Bit 7
Register Reset
DESCRIPTION
0 – Keep current register setting,
1 – Reset to default
0 – Normal ; 1 – Reset
I2C Watchdog
Timer Reset
Charger Configuration
Bit 5
CHG_CONFIG[1]
00 – Charge Disable, 01 – Charge Battery,
10/11 – OTG
Bit 4
CHG_CONFIG[0]
Minimum System Voltage Limit
Bit 3
SYS_MIN[2]
0.4V
Bit 2
SYS_MIN[1]
0.2V
Bit 1
SYS_MIN[0]
0.1V
Boost Mode Current Limit
Bit 0
BOOST_LIM
0 – 500mA, 1 – 1.3A
Bit 6
NOTE
Default: Keep current register setting (0)
Back to 0 after register reset
Default: Normal (0)
Back to 0 after timer reset
Default: Charge Battery (01)
Offset: 3.0V, Range 3.0V-3.7V
Default: 3.5V (101)
Default: 1.3A (1)
Charge Current Control Register REG02 (default 01100000, or 60)
BIT
Fast Charge Current Limit
Bit 7
ICHG[5]
Bit 6
ICHG[4]
Bit 5
ICHG[3]
Bit 4
ICHG[2]
Bit 3
ICHG[1]
Bit 2
ICHG[0]
Bit 1
Reserved
Bit 0
FORCE_20PCT
DESCRIPTION
NOTE
2048mA
1024mA
512mA
256mA
128mA
64mA
0 - Reserved
0 – ICHG as REG02[7:2] programmed
1 – ICHG as 20% of REG02[7:2] programmed
Offset: 512mA
Range: 512-2496mA
Default: 2048mA (011000)
Default: ICHG as REG02[7:2] programmed (0)
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
15
bq24196
SLUSB98 – OCTOBER 2012
www.ti.com
Pre-Charge/Termination Current Control Register REG 03 (default 00010001, or 11)
BIT
DESCRIPTION
Pre-Charge Current Limit
Bit 7
IPRECHG[3] 1024mA
Bit 6
IPRECHG[2] 512mA
Bit 5
IPRECHG[1] 256mA
Bit 4
IPRECHG[0] 128mA
Termination Current Limit
Bit 3
ITERM[3]
1024mA
Bit 2
ITERM[2]
512mA
Bit 1
ITERM[1]
256mA
Bit 0
ITERM[0]
128mA
NOTE
Offset: 128mA,
Range: 128mA – 2048mA
Default: 256mA (0001)
Offset: 128mA
Range: 128mA – 2048mA
Default: 256mA (0001)
Charge Voltage Control Register REG04 (default 11001010, or CA)
BIT
DESCRIPTION
Charge Voltage Limit
Bit 7
VREG[5]
512mV
Bit 6
VREG[4]
256mV
Bit 5
VREG[3]
128mV
Bit 4
VREG[2]
64mV
Bit 3
VREG[1]
32mV
Bit 2
VREG[0]
16mV
Battery Precharge to Fast Charge Threshold
Bit 1
BATLOWV
0 – 2.8V, 1 – 3.0V
Battery Recharge Threshold (below battery regulation voltage)
Bit 0
VRECHG
0 – 100mV, 1 – 300mV
NOTE
Offset: 3.504V
Range: 3.504V – 4.400V (111000)
Default: 4.304V (110010)
Default: 3.0V (1)
Default: 100mV (0)
Charge Termination/Timer Control Register REG05 (default 10011010, or 9A)
BIT
DESCRIPTION
Charging Termination Enable
Bit 7
EN_TERM
0 – Disable, 1 – Enable
Termination Indicator Threshold
Bit 6
TERM_STAT
0 – Match ITERM,
1 – STAT pin high before actual termination
when charge current below 800 mA
I2C Watchdog Timer Setting
Bit 5
WATCHDOG[1] 00 – Disable timer, 01 – 40s, 10 – 80s, 11 –
Bit 4
WATCHDOG[0] 160s
Charging Safety Timer Enable
Bit 3
EN_TIMER
0 – Disable, 1 – Enable
Fast Charge Timer Setting
Bit 2
CHG_TIMER[1] 00 – 5 hrs, 01 – 8 hrs, 10 – 12 hrs, 11 – 20
Bit 1
CHG_TIMER[0] hrs
Bit 0
16
Reserved
NOTE
Default: Enable termination (1)
Default Match ITERM (0)
Default: 40s (01)
Default: Enable (1)
Default: 8hours (01)
(See Charging Safety Timer for details)
0 - Reserved
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
bq24196
www.ti.com
SLUSB98 – OCTOBER 2012
Thermal Regulation Control Register REG06 (default 00000011, or 03)
BIT
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Thermal
Bit 1
Bit 0
DESCRIPTION
Reserved
0 - Reserved
Reserved
0 - Reserved
Reserved
0 - Reserved
Reserved
0 - Reserved
Reserved
0 - Reserved
Reserved
0 - Reserved
Regulation Threshold
TREG[1]
00 – 60°C, 01 – 80°C, 10 – 100°C, 11 –
120°C
TREG[0]
NOTE
Default: 120°C (11)
Misc Operation Control Register REG07 (default 01001011, or 4B)
BIT
DESCRIPTION
Set default input current limit from PSEL/OTG pins
Bit 7
DPDM_EN
0 – Not in D+/D– detection;
1 – Force D+/D– detection
Safety Timer Setting during Input DPM and Thermal Regulation
Bit 6
TMR2X_EN
0 – Safety timer not slowed by 2X during input DPM
or thermal regulation,
1 – Safety timer slowed by 2X during input DPM or
thermal regulation
Force BATFET Off
Bit 5
BATFET_Disable
0 – Allow Q4 turn on, 1 – Turn off Q4
Bit 4
Reserved
0 - Reserved
Bit 3
Reserved
1 - Reserved
Bit 2
Reserved
0 - Reserved
Bit 1
INT_MASK[1]
0 – No INT during CHRG_FAULT, 1 – INT on
CHRG_FAULT
Bit 0
INT_MASK[0]
0 – No INT during BAT_FAULT, 1 – INT on
BAT_FAULT
NOTE
Default: Not in D+/D– detection (0), Back to 0
after detection complete
Default: Safety timer slowed by 2X (1)
Default: Allow Q4 turn on(0)
Default: INT on CHRG_FAULT (1)
Default: INT on BAT_FAULT (1)
System Status Register REG08
BIT
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
VBUS_STAT[1]
VBUS_STAT[0]
CHRG_STAT[1]
CHRG_STAT[0]
DPM_STAT
PG_STAT
THERM_STAT
VSYS_STAT
DESCRIPTION
00 – Unknown (no input, or DPDM detection incomplete), 01 – USB host, 10 – Adapter port, 11 – OTG
00 – Not Charging, 01 – Pre-charge (<VBATLOWV), 10 – Fast Charging, 11 – Charge Termination Done
0 – Not DPM, 1 – VINDPM or IINDPM
0 – Not Power Good, 1 – Power Good
0 – Normal, 1 – In Thermal Regulation
0 – Not in VSYSMIN regulation (BAT>VSYSMIN), 1 – In VSYSMIN regulation (BAT<VSYSMIN)
Fault Register REG09
BIT
Bit 7
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
WATCHDOG_FAULT
CHRG_FAULT[1]
CHRG_FAULT[0]
BAT_FAULT
NTC_FAULT[2]
NTC_FAULT[1]
NTC_FAULT[0]
DESCRIPTION
0 – Normal, 1- Watchdog timer expiration
00 – Normal, 01 – Input fault (VBUS OVP or VBAT<VBUS<3.8V), 10 - Thermal shutdown,
11 – Charge Safety Timer Expiration
0 – Normal, 1 – BATOVP
000 – Normal, 101 – Cold, 110 – Hot
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
17
bq24196
SLUSB98 – OCTOBER 2012
www.ti.com
Vender / Part / Revision Status Register REG0A
BIT
Bit 7
Reserved
Bit 6
Reserved
Device Configuration
Bit 5
PN[2]
Bit 4
PN[1]
Bit 3
PN[0]
Bit 2
TS_PROFILE
Bit 1
DEV_REG[0]
Bit 0
DEV_REG[1]
DESCRIPTION
0 - Reserved
0 - Reserved
101
0 - Cold/Hot window
11
DETAILED DESCRIPTION
The bq24196 is an I2C controlled power path management device and a single cell Li-Ion battery charger. It
integrates the input reverse-blocking FET (RBFET, Q1), high-side switching FET (HSFET, Q2), low-side
switching FET (LSFET, Q3), and BATFET (Q4) between system and battery. The device also integrates the
bootstrap diode for the high-side gate drive.
Device Power Up
Power-On-Reset (POR)
The internal bias circuits are powered from the higher voltage of VBUS and BAT. When VBUS or VBAT rises
above UVLOZ, the sleep comparator, battery depletion comparator and BATFET driver are active. I2C interface
is ready for communication and all the registers are reset to default value. The host can access all the registers
after POR.
Power Up from Battery without DC Source
If only battery is present and the voltage is above depletion threshold (VBAT_DEPL), the BATFET turns on and
connects battery to system. The REGN LDO stays off to minimize the quiescent current. The low RDSON in
BATFET and the low quiescent current on BAT minimize the conduction loss and maximize the battery run time.
The device always monitors the discharge current through BATFET. When the system is overloaded or shorted,
the device will immediately turn off BATFET and keep BATFET off until the input source plugs in again.
BATFET Turn Off
The BATFET can be forced off by the host through I2C REG07[5]. This bit allows the user to independently turn
off the BATFET when the battery condition becomes abnormal during charging. When BATFET is off, there is no
path to charge or discharge the battery.
When battery is not attached, the BATFET should be turned off by setting REG07[5] to 1 to disable charging and
supplement mode.
Shipping Mode
When end equipment is assembled, the system is connected to battery through BATFET. There will be a small
leakage current to discharge the battery even when the system is powered off. In order to extend the battery life
during shipping and storage, the device can turn off BATFET so that the system voltage is zero to minimize the
leakage.
In order to keep BATFET off during shipping mode, the host has to disable the watchdog timer (REG05[5:4]=00)
and disable BATFET (REG07[5]=1) at the same time.
Once the BATFET is disabled, the BATFET can be turned on by plugging in adapter.
18
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
bq24196
www.ti.com
SLUSB98 – OCTOBER 2012
Power Up from DC Source
When the DC source plugs in, the bq24196 checks the input source voltage to turn on REGN LDO and all the
bias circuits. It also checks the input current limit before starts the buck converter.
REGN LDO
The REGN LDO supplies internal bias circuits as well as the HSFET and LSFET gate drive. The LDO also
provides bias rail to TS1/TS2 external resistors. The pull-up rail of STAT and PG can be connected to REGN as
well.
The REGN is enabled when all the conditions are valid.
1. VBUS above UVLOZ
2. VBUS above battery + VSLEEPZ in buck mode or VBUS below battery + VSLEEPZ in boost mode
3. After typical 220ms delay (100ms minimum) is complete
If one of the above conditions is not valid, the device is in high impedance mode (HIZ) with REGN LDO off. The
device draws less than 50µA from VBUS during HIZ state. The battery powers up the system when the device is
in HIZ.
Input Source Qualification
After REGN LDO powers up, the bq24196 checks the current capability of the input source. The input source has
to meet the following requirements to start the buck converter.
1. VBUS voltage below 18V (not in ACOV)
2. VBUS voltage above 3.8V when pulling 30mA (poor source detection)
Once the input source passes all the conditions above, the status register REG08[2] goes high and the PG pin
goes low. An INT is asserted to the host.
If the device fails the poor source detection, it will repeat the detection every 2 seconds.
Input Current Limit Detection
The USB ports on personal computers are convenient charging source for portable devices (PDs). If the portable
device is attached to a USB host, the USB specification requires the portable device to draw limited current
(100mA/500mA in USB 2.0, and 150mA/900mA in USB 3.0). If the portable device is attached to a charging port,
it is allowed to draw up to 1.5A.
After the PG is LOW or REG08[2] goes HIGH, the charger device always runs input current limit detection when
a DC source plugs in unless the charger is in HIZ during host mode.
The bq24196 sets input current limit through PSEL and OTG pins.
After the input current limit detection is done, the host can write to REG00[2:0] to change the input current limit.
PSEL/OTG Pins Set Input Current Limit
The bq24196 has PSEL. It directly takes the USB PHY device output to decide whether the input is USB host or
charging port.
Table 2. bq24196 Input Current Limit Detection
PSEL
OTG
INPUT CURRENT LIMIT
REG08[7:6]
HIGH
LOW
100 mA
01
HIGH
HIGH
500 mA
01
LOW
—
3A
10
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
19
bq24196
SLUSB98 – OCTOBER 2012
www.ti.com
HIZ State wth 100mA USB Host
In battery charging spec, the good battery threshold is the minimum charge level of a battery to power up the
portable device successfully. When the input source is 100mA USB host, and the battery is above bat-good
threshold (VBATGD), the device follows battery charging spec and enters high impedance state (HIZ). In HIZ state,
the device is in the lowest quiescent state with REGN LDO and the bias circuits off. The charger device sets
REG00[7] to 1, and the VBUS current during HIZ state will be less than 30µA. The system is supplied by the
battery.
Once the charger device enters HIZ state in host mode, it stays in HIZ until the host writes REG00[7]=0. When
the processor host wakes up, it is recommended to first check if the charger is in HIZ state.
In default mode, the charger IC will reset REG00[7] back to 0 when input source is removed. When another
source plugs in, the charger IC will run detection again, and update the input current limit.
Force Input Current Limit Detection
The host can force the charger device to run input current limit detection by setting REG07[7]=1. After the
detection is complete, REG07[7] will return to 0 by itself.
Converter Power-Up
After the input current limit is set, the converter is enabled and the HSFET and LSFET start switching. If battery
charging is disabled, BATFET turns off. Otherwise, BATFET stays on to charge the battery.
The bq24196 provides soft-start when ramp up the system rail. When the system rail is below 2.2V, the input
current limit is forced to 100mA. After the system rises above 2.2V, the charger device sets the input current limit
set by the lower value between register and ILIM pin.
As a battery charger, the bq24196 deploys a 1.5MHz step-down switching regulator. The fixed frequency
oscillator keeps tight control of the switching frequency under all conditions of input voltage, battery voltage,
charge current and temperature, simplifying output filter design.
A type III compensation network allows using ceramic capacitors at the output of the converter. An internal sawtooth ramp is compared to the internal error control signal to vary the duty cycle of the converter. The ramp
height is proportional to the PMID voltage to cancel out any loop gain variation due to a change in input voltage.
In order to improve light-load efficiency, the device switches to PFM control at light load when battery is below
minimum system voltage setting or charging is disabled. During the PFM operation, the switching duty cycle is
set by the ratio of SYS and VBUS.
Boost Mode Operation from Battery
The bq24196 supports boost converter operation to deliver power from the battery to other portable devices
through USB port. The boost mode output current rating meets the USB On-The-Go 500mA output requirement.
The maximum output current is 1.3A. The boost operation can be enabled if the following conditions are valid:
1. BAT above BATLOWV threshold (VBATLOWV set by REG04[1])
2. VBUS less than BAT+VSLEEP (in sleep mode)
3. Boost mode operation is enabled (OTG pin HIGH and REG01[5:4]=10)
4. After 220ms delay from boost mode enable
In boost mode, the bq24196 employs a 1.5MHz step-up switching regulator. Similar to buck operation, the device
switches from PWM operation to PFM operation at light load to improve efficiency.
During boost mode, the status register REG08[7:6] is set to 11, the VBUS output is 5V and the output current
can reach up to 500mA or 1.3A, selected via I2C (REG01[0]).
Any fault during boost operation, including VBUS over-voltage or over-current, sets the fault register REG09[6] to
1 and an INT is asserted.
Power Path Management
The bq24196 accommodates a wide range of input sources from USB, wall adapter, to car battery. The device
provides automatic power path selection to supply the system (SYS) from input source (VBUS), battery (BAT), or
both.
20
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
bq24196
www.ti.com
SLUSB98 – OCTOBER 2012
Narrow VDC Architecture
The device deploys Narrow VDC architecture (NVDC) with BATFET separating system from battery. The
minimum system voltage is set by REG01[3:1]. Even with a fully depleted battery, the system is regulated above
the minimum system voltage (default 3.5V).
When the battery is below minimum system voltage setting, the BATFET operates in linear mode (LDO mode),
and the system is 150mV above the minimum system voltage setting. As the battery voltage rises above the
minimum system voltage, BATFET is fully on and the voltage difference between the system and battery is the
VDS of BATFET.
When the battery charging is disabled or terminated, the system is always regulated at 150mV above the
minimum system voltage setting. The status register REG08[0] goes high when the system is in minimum system
voltage regulation.
4.5
4.3
Charge Enabled
4.1
SYS
(V)
Charge Disabled
3.9
3.7
3.5
Minimum System Voltage
3.3
3.1
2.7 2.9 3.1 3.3 3.5 3.7 3.9 4.1 4.3
BAT (V)
Figure 22. V(SYS) vs V(BAT)
Dynamic Power Management
To meet maximum current limit in USB spec and avoid over loading the adapter, the bq24196 features Dynamic
Power Management (DPM), which continuously monitors the input current and input voltage.
When input source is over-loaded, either the current exceeds the input current limit (REG00[2:0]) or the voltage
falls below the input voltage limit (REG00[6:3]). The device then reduces the charge current until the input current
falls below the input current limit and the input voltage rises above the input voltage limit.
When the charge current is reduced to zero, but the input source is still overloaded, the system voltage starts to
drop. Once the system voltage falls below the battery voltage, the device automatically enters the supplement
mode where the BATFET turns on and battery starts discharging so that the system is supported from both the
input source and battery.
During DPM mode (either VINDPM or IINDPM), the status register REG08[3] will go high.
Figure 23 shows the DPM response with 9V/1.2A adapter, 3.2V battery, 2.8A charge current and 3.4V minimum
system voltage setting.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
21
bq24196
SLUSB98 – OCTOBER 2012
www.ti.com
Voltage
VBUS
9V
SYS
3.6V
3.4V
3.2V
3.18V
BAT
Current
4A
ICHG
3.2A
2.8A
ISYS
1.2A
1.0A
0.5A
IIN
-0.6A
DPM
DPM
Supplement
Figure 23. DPM Response
Supplement Mode
When the system voltage falls below the battery voltage, the BATFET turns on and the BATFET gate is
regulated the gate drive of BATFET so that the minimum BATFET VDS stays at 30mV when the current is low.
This prevents oscillation from entering and exiting the supplement mode. As the discharge current increases, the
BATFET gate is regulated with a higher voltage to reduce RDSON until the BATFET is in full conduction. At this
point onwards, the BATFET VDS linearly increases with discharge current. Figure 24 shows the V-I curve of the
BATFET gate regulation operation. BATFET turns off to exit supplement mode when the battery is below battery
depletion threshold.
4.5
4.0
CURRENT (A)
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
0
5
10
15
20
25
30
35
40
45
50
55
V(BAT-SYS) (mV)
Figure 24. BATFET V-I Curve
Battery Charging Management
The bq24196 charges 1-cell Li-Ion battery with up to 2.5A charge current for high capacity tablet battery. The
12mΩ BATFET improves charging efficiency and minimizes the voltage drop during discharging.
Autonomous Charging Cycle
With battery charging enabled at POR (REG01[5:4]=01), the bq24196 can complete a charging cycle without
host involvement. The device default charging parameters are listed in .
22
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
bq24196
www.ti.com
SLUSB98 – OCTOBER 2012
Table 3. Charging Parameter Default Setting
(1)
A
•
•
•
•
•
DEFAULT MODE
bq24196
Charging Voltage
4.208 V
Charging Current
2.036 A
Pre-charge Current
256 mA
Termination Current
256 mA
Temperature Profile
Hot/Cold
Safety Timer
8 hours (1)
See section Charging Safety Timer for more information.
new charge cycle starts when the following conditions are valid:
Converter starts
Battery charging is enabled by I2C register bit (REG01[5:4]) = 01 and CE is low
No thermistor fault on TS1 and TS2
No safety timer fault
BATFET is not forced to turn off (REG07[5])
The charger device automatically terminates the charging cycle when the charging current is below termination
threshold and charge voltage is above recharge threshold. When a full battery voltage is discharged below
recharge threshold (REG04[0]), the bq24196 automatically starts another charging cycle.
The STAT output indicates the charging status of charging (LOW), charging complete or charge disable (HIGH)
or charging fault (Blinking). The status register REG08[5:4] indicates the different charging phases: 00-charging
disable, 01-precharge, 10-fast charge (constant current) and constant voltage mode, 11-charging done. Once a
charging cycle is complete, an INT is asserted to notify the host.
The host can always control the charging operation and optimize the charging parameters by writing to the
registers through I2C.
Battery Charging Profile
The device charges the battery in three phases: preconditioning, constant current and constant voltage. At the
beginning of a charging cycle, the device checks the battery voltage and applies current.
Table 4. Charging Current Setting
VBAT
CHARGING CURRENT
REG DEFAULT SETTING
REG08[5:4]
<2V
100mA
–
01
2V-3V
REG03[7:4]
256mA
01
>3V
REG02[7:2]
2048mA
10
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
23
bq24196
SLUSB98 – OCTOBER 2012
www.ti.com
If the charger device is in DPM regulation or thermal regulation during charging, the actual charging current will
be less than the programmed value. In this case, termination is temporarily disabled and the charging safety
timer is counted at half the clock rate.
Regulation Voltage
(3.5V – 4.4V)
Battery Voltage
Fast Charge Current
(500mA-4020mA)
Charge Current
VBAT_LOWV (2.8V/3V)
VBAT_SHORT (2V)
IPRECHARGE (128mA-2048mA)
ITERMINATION (128mA-2048mA)
IBATSHORT (100mA)
Trickle Charge
Pre-charge
Fast Charge and Voltage Regulation
Safety Timer
Expiration
Figure 25. Battery Charging Profile
Thermistor Cold/Hot Temperature Window
The bq24196 continuously monitors battery temperature by measuring the voltage between the TS pins and
ground, typically determined by a negative temperature coefficient thermistor and an external voltage divider. The
device compares this voltage against its internal thresholds to determine if charging is allowed. To initiate a
charge cycle, the battery temperature must be within the VLTF to VHTF thresholds. During the charge cycle the
battery temperature must be within the VLTF to VTCO thresholds, else the device suspends charging and waits
until the battery temperature is within the VLTF to VHTF range.
REGN
bq24196
RT1
TS
RT2
RTH
103AT
Figure 26. TS Resistor Network
When the TS fault occurs, the fault register REG09[2:0] indicates the actual condition on each TS pin and an INT
is asserted to the host. The STAT pin indicates the fault when charging is suspended.
24
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
bq24196
www.ti.com
SLUSB98 – OCTOBER 2012
TEMPERATURE RANGE TO
INITIATE CHARGE
TEMPERATURE RANGE
DURING A CHARGE CYCLE
VREF
VREF
CHARGE SUSPENDED
CHARGE SUSPENDED
VLTF
VLTF
VLTFH
VLTFH
CHARGE at full C
CHARGE at full C
VHTF
VTCO
CHARGE SUSPENDED
CHARGE SUSPENDED
AGND
AGND
Figure 27. TS Pin Thermistor Sense Thresholds
Assuming a 103AT NTC thermistor is used on the battery pack , the value RT1 and RT2 can be determined by
using the following equation:
æ 1
1 ö
VVREF ´ RTHCOLD ´ RTHHOT ´ ç
÷
VLTF VTCO ø
è
RT2 =
æV
ö
æV
ö
RTHHOT ´ ç VREF - 1÷ - RTHCOLD ´ ç VREF - 1÷
V
V
è LTF
ø
è TCO
ø
VVREF
-1
VLTF
RT1 =
1
1
+
RT2 RTHCOLD
(1)
Select 0°C to 45°C range for Li-ion or Li-polymer battery,
RTHCOLD = 27.28 kΩ
RTHHOT = 4.911 kΩ
RT1 = 5.52 kΩ
RT2 = 31.23 kΩ
Charging Termination
The bq24196 terminates a charge cycle when the battery voltage is above recharge threshold, and the current is
below termination current. After the charging cycle is complete, the BATFET turns off. The converter keeps
running to power the system, and BATFET can turn back on to engage supplement mode.
When termination occurs, the status register REG09[5:4] is 11, and an INT is asserted to the host. Termination is
temporarily disabled if the charger device is in input current/voltage regulation or thermal regulation. Termination
can be disabled by writing 0 to REG05[7].
Termination when REG02[0] = 1
When REG02[0] is HIGH to reduce the charging current by 80%, the charging current could be less than the
termination current. The charger device termination function should be disabled. When the battery is charged to
fully capacity, the host disables charging through CE pin or REG01[5:4].
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
25
bq24196
SLUSB98 – OCTOBER 2012
www.ti.com
Termination when REG05[6] = 1
Usually the STAT bit indicates charging complete when the charging current falls below termination threshold.
Write REG05[6]=1 to enable an early “charge done” indication on STAT pin. The STAT pin goes high when the
charge current reduces below 800mA. The charging cycle is still on-going until the current falls below the
termination threshold.
Charging Safety Timer
The bq24196 has safety timer to prevent extended charging cycle due to abnormal battery conditions.
In default mode, the device keeps charging the battery with 5-hour fast charging safety timer regardless of
REG05[2:1] default value. At the end of the 5 hours, the EN_HIZ (REG00[7]) is set to signal the buck converter
stops and the system load is supplied by the battery. The EN_HIZ bit can be cleared to restart the buck
converter.
In host mode, the device keeps charging the battery until the fast charging safety timer expired. The duration of
safety timer can be set by the REG05[2:1] bits (default = 8 hours). At the end of safety timer, the EN_HIZ
(REG00[7]) is cleared to signal the buck converter continues to operation to supply system load.
The safety timer is 1 hour when the battery is below BATLOWV threshold. The user can program fast charge
safety timer through I2C (REG05[2:1]). When safety timer expires, the fault register REG09[5:4] goes 11 and an
INT is asserted to the host. The safety timer feature can be disabled via I2C (REG05[3]).
The following actions restart the safety timer:
• At the beginning of a new charging cycle
• Toggle the CE pin HIGH to LOW to HIGH (charge enable)
• Write REG01[5:4] from 00 to 01 (charge enable)
• Write REG05[3] from 0 to 1 (safety timer enable)
• Write REG01[7] to 1 (software reset)
During input voltage/current regulation or thermal regulation, the safety timer counts at half clock rate since the
actual charge current is likely to be below the register setting. For example, if the charger is in input current
regulation (IINDPM) throughout the whole charging cycle, and the safety time is set to 5 hours, the safety timer
will expire in 10 hours. This feature can be disabled by writing 0 to REG07[6].
USB Timer when Charging from USB100mA Source
The total charging time in default mode from USB100mA source is limited by a 45-min max timer. At the end of
the timer, the device stops the converter and goes to HIZ.
Host Mode and Default Mode
The bq24196 is a host controlled device, but it can operate in default mode without host management. In default
mode, bq24196 can be used as an autonomous charger with no host or with host in sleep.
When the charger is in default mode, REG09[7] is HIGH. When the charger is in host mode, REG09[7] is LOW.
After power-on-reset, the device starts in watchdog timer expiration state, or default mode. All the registers are in
the default settings.
Any write command to bq24196 transitions the device from default mode to host mode. All the device parameters
can be programmed by the host. To keep the device in host mode, the host has to reset the watchdog timer by
writing 1 to REG01[6] before the watchdog timer expires (REG05[5:4]), or disable watchdog timer by setting
REG05[5:4]=11.
26
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
bq24196
www.ti.com
SLUSB98 – OCTOBER 2012
POR
watchdog timer expired
Reset registers
I2C interface enabled
Host Mode
Y
I2C Write?
Start watchdog timer
Host programs registers
N
Default Mode
Reset watchdog timer
Reset registers
N
Reset REG01
bit[6]?
Y
Y
N
I2C Write?
Y
Watchdog Timer
Expired?
N
Figure 28. Watchdog Timer Flow Chart
Plug in USB100mA Source with Good Battery
When the input source is detected as 100mA USB host, and the battery voltage is above batgood threshold
(VBATGD), the charger device enters HIZ state to meet the battery charging spec requirement.
If the charger device is in host mode, it will stay in HIZ state even after the USB100mA source is removed, and
the adapter plugs in. During the HIZ state, REG00[7] is set HIGH and the system load is supplied from battery. It
is recommended that the processor host always checks if the charger IC is in HIZ state when it wakes up. The
host can write REG00[7] to 0 to exit HIZ state.
If the charger is in default mode, when the DC source is removed, the charger device will get out of HIZ state
automatically. When the input source plugs in again, the charger IC runs detection on the input source and
update the input current limit.
USB Timer when Charging from USB100mA Source
The total charging time in default mode from USB100mA source is limited by a 45-min max timer. At the end of
the timer, the device stops the converter and goes to HIZ.
Status Outputs (PG, STAT, and INT)
Power Good Indicator (PG)
In bq24196, PG goes LOW to indicate a good input source when:
1. VBUS above UVLO
2. VBUS above battery (not in sleep)
3. VBUS below ACOV threshold
4. VBUS above 3.8V when 30mA current is applied (not a poor source)
Charging Status Indicator (STAT)
The bq24196 indicates charging state on the open drain STAT pin. The STAT pin can drive LED as the
application diagram shows.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
27
bq24196
SLUSB98 – OCTOBER 2012
www.ti.com
Table 5. STAT Pin State
CHARGING STATE
STAT
Charging in progress (including recharge)
LOW
Charging complete
HIGH
Sleep mode, charge disable
HIGH
Charge suspend (Input over-voltage, TS fault, timer fault, input or system overvoltage)
blinking at 1Hz
Interrupt to Host (INT)
In some applications, the host does not always monitor the charger operation. The INT notifies the system on the
device operation. The following events will generate 256us INT pulse.
• USB/adapter source identified (through PSEL and OTG pins)
• Good input source detected
– not in sleep
– not in ACOV
– current limit above 30mA
• Input removed or ACOV
• Charge Complete
• Any FAULT event in REG09
When a fault occurs, the charger device sends out INT and latches the fault state in REG09 until the host reads
the fault register. Before the host reads REG09, the charger device would not send any INT upon new faults
except NTC fault (REG09[2:0]). The NTC fault is not latched and always reports the current thermistor
conditions. In order to read the current fault status, the host has to read REG09 two times consecutively. The 1st
reads fault register status from the last INT and the 2nd reads the current fault register status.
Protections
Input Current Limit on ILIM
For safe operation, the bq24196 has an additional hardware pin on ILIM to limit maximum input current on ILIM
pin. The input maximum current is set by a resistor from ILIM pin to ground as:
1V
IINMAX =
´ 530
RILIM
(2)
The actual input current limit is the lower value between ILIM setting and register setting (REG00[2:0]). For
example, if the register setting is 111 for 3A, and ILIM has a 353Ω resistor to ground for 1.5A, the input current
limit is 1.5A. ILIM pin can be used to set the input current limit rather than the register settings.
The device regulates ILIM pin at 1V. If ILIM voltage exceeds 1V, the device enters input current regulation (Refer
to Dynamic Power Path Management section).
The voltage on ILIM pin is proportional to the input current. ILIM pin can be used to monitor the input current
following Equation 3:
V
I IN = ILIM ´ IINMAX
(3)
1V
For example, if ILIM pin sets 2A, and the ILIM voltage is 0.6V, the actual input current 1.2A. If ILIM pin is open,
the input current is limited to zero since ILIM voltage floats above 1V. If ILIM pin is short, the input current limit is
set by the register.
Thermal Regulation and Thermal Shutdown
The bq24196 monitors the internal junction temperature TJ to avoid overheat the chip and limits the IC surface
temperature. When the internal junction temperature exceeds the preset limit (REG06[1:0]), the device lowers
down the charge current. The wide thermal regulation range from 60°C to 120°C allows the user to optimize the
system thermal performance.
28
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
bq24196
www.ti.com
SLUSB98 – OCTOBER 2012
During thermal regulation, the actual charging current is usually below the programmed battery charging current.
Therefore, termination is disabled, the safety timer runs at half the clock rate, and the status register REG08[1]
goes high.
Additionally, the device has thermal shutdown to turn off the converter. The fault register REG09[5:4] is 10 and
an INT is asserted to the host.
Voltage and Current Monitoring in Buck Mode
The bq24196 closely monitors the input and system voltage, as well as HSFET and LSFET current for safe buck
mode operation.
Input Over-Voltage (ACOV)
The maximum input voltage for buck mode operation is 18V. If VBUS voltage exceeds 18V, the device stops
switching immediately. During input over voltage (ACOV), the fault register REG09[5:4] will be set to 01. An INT
is asserted to the host.
System Over-Voltage Protection (SYSOVP)
The charger device monitors the voltage at SYS. When system over-voltage is detected, the converter is stopped
to protect components connected to SYS from high voltage damage.
Voltage and Current Monitoring in Boost Mode
The bq24196 closely monitors the VBUS voltage, as well as HSFET and LSFET current to ensure safe boost
mode operation.
VBUS Over-Voltage Protection
The boost mode regulated output is 5V. When an adapter plugs in during boost mode, the VBUS voltage will rise
above regulation target. Once the VBUS voltage exceeds 5.3V, the bq24196 stops switching and the device exits
boost mode. The fault register REG09[6] is set high to indicate fault in boost operation. An INT is asserted to the
host.
Battery Protection
Battery Over-Current Protection (BATOVP)
The battery over-voltage limit is clamped at 4% above the battery regulation voltage. When battery over voltage
occurs, the charger device immediately disables charge. The fault register REG09[5] goes high and an INT is
asserted to the host.
Charging During Battery Short Protection
If the battery voltage falls below 2V, the charge current is reduced to 100mA for battery safety.
System Over-Current Protection
If the system is shorted or exceeds the over-current limit, the BATFET is latched off. DC source insertion on
VBUS is required to reset the latch-off condition and turn on BATFET.
Serial Interface
The bq24196 uses I2C compatible interface for flexible charging parameter programming and instantaneous
device status reporting. I2CTM is a bi-directional 2-wire serial interface developed by Philips Semiconductor (now
NXP Semiconductors). Only two bus lines are required: a serial data line (SDA) and a serial clock line (SCL).
Devices can be considered as masters or slaves when performing data transfers. A master is the device which
initiates a data transfer on the bus and generates the clock signals to permit that transfer. At that time, any
device addressed is considered a slave.
The device operates as a slave device with address 6BH, receiving control inputs from the master device like
micro controller or a digital signal processor. The I2C interface supports both standard mode (up to 100kbits), and
fast mode (up to 400kbits).
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
29
bq24196
SLUSB98 – OCTOBER 2012
www.ti.com
Both SDA and SCL are bi-directional lines, connecting to the positive supply voltage via a current source or pullup resistor. When the bus is free, both lines are HIGH. The SDA and SCL pins are open drain.
Data Validity
The data on the SDA line must be stable during the HIGH period of the clock. The HIGH or LOW state of the
data line can only change when the clock signal on the SCL line is LOW. One clock pulse is generated for each
data bit transferred.
SDA
SCL
Data line stable;
Data valid
Change
of data
allowed
Figure 29. Bit Transfer on the I2C Bus
START and STOP Conditions
All transactions begin with a START (S) and can be terminated by a STOP (P). A HIGH to LOW transition on the
SDA line while SCl is HIGH defines a START condition. A LOW to HIGH transition on the SDA line when the
SCL is HIGH defines a STOP condition.
START and STOP conditions are always generated by the master. The bus is considered busy after the START
condition, and free after the STOP condition.
SDA
SDA
SCL
SCL
STOP (P)
START (S)
Figure 30. START and STOP conditions
Byte Format
Every byte on the SDA line must be 8 bits long. The number of bytes to be transmitted per transfer is
unrestricted. Each byte has to be followed by an Acknowledge bit. Data is transferred with the Most Significant
Bit (MSB) first. If a slave cannot receive or transmit another complete byte of data until it has performed some
other function, it can hold the clock line SCL low to force the master into a wait state (clock stretching). Data
transfer then continues when the slave is ready for another byte of data and release the clock line SCL.
30
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
bq24196
www.ti.com
SLUSB98 – OCTOBER 2012
Acknowledgement
signal from receiver
Acknowledgement
signal from slave
MSB
SDA
SCL
S or Sr
2
1
7
8
2
1
9
ACK
START or
Repeated
START
8
9
ACK
P or Sr
STOP or
Repeated
START
Figure 31. Data Transfer on the I2C Bus
Acknowledge (ACK) and Not Acknowledge (NACK)
The acknowledge takes place after every byte. The acknowledge bit allows the receiver to signal the transmitter
that the byte was successfully received and another byte may be sent. All clock pulses, including the
acknowledge 9th clock pulse, are generated by the master.
The transmitter releases the SDA line during the acknowledge clock pulse so the receiver can pull the SDA line
LOW and it remains stable LOW during the HIGH period of this clock pulse.
When SDA remains HIGH during the 9th clock pulse, this is the Not Acknowledge signal. The master can then
generate either a STOP to abort the transfer or a repeated START to start a new transfer.
Slave Address and Data Direction Bit
After the START, a slave address is sent. This address is 7 bits long followed by the eighth bit as a data direction
bit (bit R/W). A zero indicates a transmission (WRITE) and a one indicates a request for data (READ).
SDA
SCL
S
1-7
8
9
START
ADDRESS
R/W
ACK
8
1-7
9
8
1-7
ACK
DATA
DATA
9
P
ACK
STOP
Figure 32. Complete Data Transfer
Single Read and Write
1
7
1
1
8
1
8
1
1
S
Slave Address
0
ACK
Reg Addr
ACK
Data Addr
ACK
P
Figure 33. Single Write
1
7
1
1
8
1
1
7
1
1
S
Slave Address
0
ACK
Reg Addr
ACK
S
Slave Address
1
ACK
8
1
1
Data
NCK
P
Figure 34. Single Read
If the register address is not defined, the charger IC send back NACK and go back to the idle state.
Multi-Read and Multi-Write
The charger device supports multi-read and multi-write on REG00 through REG08.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
31
bq24196
SLUSB98 – OCTOBER 2012
www.ti.com
1
7
1
1
8
1
S
Slave Address
0
ACK
Reg Addr
ACK
8
1
8
1
8
1
1
Slave Address
ACK
Data to Addr+1
ACK
Data to Addr+1
ACK
P
Figure 35. Multi-Write
1
7
S
Slave Address
0
8
1
1
ACK
8
Data @ Addr
1
ACK
Reg Addr
1
7
1
1
S
Slave Address
1
ACK
1
8
1
8
1
1
ACK
Data @ Addr+1
ACK
Data @ Addr+1
ACK
P
Figure 36. Multi-Read
The fault register REG09 locks the previous fault and only clears it after the register is read. For example, if
Charge Safety Timer Expiration fault occurs but recovers later, the fault register REG09 reports the fault when it
is read the first time, but returns to normal when it is read the second time. To verify real time fault, the fault
register REG09 should be read twice to get the real condition. In addition, the fault register REG09 does not
support multi-read or multi-write.
32
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
bq24196
www.ti.com
SLUSB98 – OCTOBER 2012
APPLICATION INFORMATION
Inductor Selection
The bq24196 has 1.5 MHz switching frequency to allow the use of small inductor and capacitor values. The
Inductor saturation current should be higher than the charging current (ICHG) plus half the ripple current (IRIPPLE):
ISAT ³ ICHG + (1/ 2 ) IRIPPLE
(4)
The inductor ripple current depends on input voltage (VBUS), duty cycle (D = VBAT/VVBUS), switching frequency
(fs) and inductance (L):
V ´ D ´ (1 - D)
IRIPPLE = IN
¦s ´ L
(5)
The maximum inductor ripple current happens with D = 0.5 or close to 0.5. Usually inductor ripple is designed in
the range of (20–40%) maximum charging current as a trade-off between inductor size and efficiency for a
practical design. Typical inductor value is 2.2µH.
Input Capacitor
Input capacitor should have enough ripple current rating to absorb input switching ripple current. The worst case
RMS ripple current is half of the charging current when duty cycle is 0.5. If the converter does not operate at
50% duty cycle, then the worst case capacitor RMS current ICIN occurs where the duty cycle is closest to 50%
and can be estimated by the following equation:
I CIN = ICHG ´ D ´ (1 - D)
(6)
For best performance, VBUS should be decouple to PGND with 1μF capacitance. The remaining input capacitor
should be place on PMID.
Low ESR ceramic capacitor such as X7R or X5R is preferred for input decoupling capacitor and should be
placed to the drain of the high side MOSFET and source of the low side MOSFET as close as possible. Voltage
rating of the capacitor must be higher than normal input voltage level. 25V rating or higher capacitor is preferred
for 15V input voltage.
Output Capacitor
Output capacitor also should have enough ripple current rating to absorb output switching ripple current. The
output capacitor RMS current ICOUT is given:
I
I COUT = RIPPLE » 0.29 ´ IRIPPLE
2´ 3
(7)
The output capacitor voltage ripple can be calculated as follows:
VOUT æç
VOUT ö÷
1
DVO =
VIN ÷
8LC¦ s2 çè
ø
(8)
At certain input/output voltage and switching frequency, the voltage ripple can be reduced by increasing the
output filter LC.
The charger device has internal loop compensator. To get good loop stability, the resonant frequency of the
output inductor and output capacitor should be designed between 15kHz and 25kHz. With 2.2µH inductor, the
typical output capacitor value is 20µF. The preferred ceramic capacitor is 6V or higher rating, X7R or X5R.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
33
bq24196
SLUSB98 – OCTOBER 2012
www.ti.com
PCB Layout
The switching node rise and fall times should be minimized for minimum switching loss. Proper layout of the
components to minimize high frequency current path loop (see Figure 37) is important to prevent electrical and
magnetic field radiation and high frequency resonant problems. Here is a PCB layout priority list for proper
layout. Layout PCB according to this specific order is essential.
1. Place input capacitor as close as possible to PMID pin and GND pin connections and use shortest copper
trace connection or GND plane.
2. Place inductor input terminal to SW pin as close as possible. Minimize the copper area of this trace to lower
electrical and magnetic field radiation but make the trace wide enough to carry the charging current. Do not
use multiple layers in parallel for this connection. Minimize parasitic capacitance from this area to any other
trace or plane.
3. Put output capacitor near to the inductor and the IC. Ground connections need to be tied to the IC ground
with a short copper trace connection or GND plane.
4. Route analog ground separately from power ground. Connect analog ground and connect power ground
separately. Connect analog ground and power ground together using power pad as the single ground
connection point. Or using a 0Ω resistor to tie analog ground to power ground.
5. Use single ground connection to tie charger power ground to charger analog ground. Just beneath the IC.
Use ground copper pour but avoid power pins to reduce inductive and capacitive noise coupling.
6. Decoupling capacitors should be placed next to the IC pins and make trace connection as short as possible.
7. It is critical that the exposed power pad on the backside of the IC package be soldered to the PCB ground.
Ensure that there are sufficient thermal vias directly under the IC, connecting to the ground plane on the
other layers.
8. The via size and number should be enough for a given current path.
See the EVM design for the recommended component placement with trace and via locations. For the QFN
information, refer to SCBA017 and SLUA271.
Figure 37. High Frequency Current Path
34
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links :bq24196
PACKAGE OPTION ADDENDUM
www.ti.com
22-Oct-2012
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
BQ24196RGER
ACTIVE
VQFN
RGE
24
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
BQ24196RGET
ACTIVE
VQFN
RGE
24
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Samples
(Requires Login)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
19-Oct-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
BQ24196RGER
VQFN
RGE
24
3000
330.0
12.4
4.25
4.25
1.15
8.0
12.0
Q2
BQ24196RGET
VQFN
RGE
24
250
180.0
12.4
4.25
4.25
1.15
8.0
12.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
19-Oct-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
BQ24196RGER
VQFN
RGE
24
3000
367.0
367.0
35.0
BQ24196RGET
VQFN
RGE
24
250
210.0
185.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated