Features • Utilizes the ARM7TDMI™ ARM® Thumb® Processor Core • • • • • • • • • • • • • • • • – High-performance 32-bit RISC Architecture – High-density 16-bit Instruction Set – Leader in MIPS/Watt – Embedded ICE (In-circuit Emulation) 8K Bytes Internal SRAM Fully Programmable External Bus Interface (EBI) – Maximum External Address Space of 64M Bytes – Up to 8 Chip Selects – Software Programmable 8/16-bit External Data Bus 8-channel Peripheral Data Controller 8-level Priority, Individually Maskable, Vectored Interrupt Controller – 5 External Interrupts, Including a High-priority, Low-latency Interrupt Request 54 Programmable I/O Lines 6-channel 16-bit Timer/Counter – 6 External Clock Inputs, 2 Multi-purpose I/O Pins per Channel 2 USARTs – 2 Dedicated Peripheral Data Controller (PDC) Channels per USART – Support for up to 9-bit Data Transfers 2 Master/Slave SPI Interfaces – 2 Dedicated Peripheral Data Controller (PDC) Channels per SPI – 8- to 16-bit Programmable Data Length – 4 External Slave Chip Selects per SPI 3 System Timers – Period Interval Timer (PIT); Real-time Timer (RTT); Watchdog Timer (WDT) Power Management Controller (PMC) – CPU and Peripherals Can be Deactivated Individually Clock Generator with 32.768 kHz Low-power Oscillator and PLL – Support for 38.4 kHz Crystals – Software Programmable System Clock (up to 33 MHz) IEEE 1149.1 JTAG Boundary Scan on All Active Pins Fully Static Operation: 0 Hz to 33 MHz, Internal Frequency Range at VDDCORE = 3.0V, 85°C 2.7V to 3.6V Core and PLL Operating Voltage Range; 2.7V to 5.5V I/O Operating Voltage Range -40°C to +85°C Temperature Range Available in a 144-lead TQFP Package and in 144-ball BGA Package AT91 ARM® Thumb® Microcontrollers AT91M42800A Description The AT91M42800A is a member of the Atmel AT91 16/32-bit microcontroller family, which is based on the ARM7TDMI processor core. This processor has a high-performance 32-bit RISC architecture with a high-density 16-bit instruction set and very low power consumption. In addition, a large number of internally banked registers result in very fast exception handling, making the device ideal for real-time control applications. The AT91 ARM-based MCU family also features Atmel’s high-density, in-system programmable, nonvolatile memor y technology. The AT91M42800A has a direct connection to off-chip memory, including Flash, through the External Bus Interface. The Power Management Controller allows the user to adjust device activity according to system requirements, and, with the 32.768 kHz low-power oscillator, enables the AT91M42800A to reduce power requirements to an absolute minimum. The AT91M42800A is manufactured using Atmel’s high-density CMOS technology. By combining the ARM7TDMI processor core with on-chip SRAM and a wide range of peripheral functions including timers, serial communication controllers and a versatile clock generator on a monolithic chip, the AT91M42800A provides a highly flexible and cost-effective solution to many compute-intensive applications. Rev. 1779B–ATARM–03/02 1 Pin Configuration Figure 1. Pin Configuration in TQFP144 Package (Top View) 108 73 109 72 AT91M42800 33AI 144 37 1 36 Figure 2. Pin Configuration in BGA144 Package (Top View) 1 2 3 4 5 6 7 8 9 10 11 12 A B C D E F G H J K L M 2 AT91M42800A 1779B–ATARM–03/02 AT91M42800A Table 1. AT91M42800A Pinout in TQFP 144 Package Pin# Name Pin# Name Pin# Name Pin# Name 1 GND 37 GND 73 GND 109 GND 2 GND 38 GND 74 GND 110 GND 3 NLB/A0 39 D4 75 PB22/TIOA5 111 PA26 4 A1 40 D5 76 PB23/TIOB5 112 MODE0 5 A2 41 D6 77 PA0/IRQ0 113 XIN 6 A3 42 D7 78 PA1/IRQ1 114 XOUT 7 A4 43 D8 79 PA2/IRQ2 115 GND 8 A5 44 D9 80 PA3/IRQ3 116 PLLRCA 9 A6 45 D10 81 PA4/FIQ 117 VDDPLL 10 A7 46 D11 82 PA5/SCK0 118 PLLRCB 11 A8 47 D12 83 PA6/TXD0 119 VDDPLL 12 VDDIO 48 VDDIO 84 VDDIO 120 VDDIO 13 GND 49 GND 85 GND 121 GND 14 A9 50 D13 86 PA7/RXD0 122 NWDOVF 15 A10 51 D14 87 PA8/SCK1 123 PA27/BMS 16 A11 52 D15 88 PA9/TXD1/NTRI 124 MODE1 17 A12 53 PB6/TCLK0 89 PA10/RXD1 125 TMS 18 A13 54 PB7/TIOA0 90 PA11/SPCKA 126 TDI 19 A14 55 PB8/TIOB0 91 PA12/MISOA 127 TDO 20 A15 56 PB9/TCLK1 92 PA13/MOSIA 128 TCK 21 A16 57 PB10/TIOA1 93 PA14/NPCSA0/NSSA 129 NTRST 22 A17 58 PB11/TIOB1 94 PA15/NPCSA1 130 NRST 23 A18 59 PB12/TCLK2 95 PA16/NPCSA2 131 PA28 24 VDDIO 60 VDDIO 96 VDDIO 132 VDDIO 25 GND 61 GND 97 GND 133 GND PA29/PME 26 A19 62 PB13/TIOA2 98 PA17/NPCSA3 134 27 PB2/A20/CS7 63 PB14/TIOB2 99 PA18/SPCKB 135 NWAIT 28 PB3/A21/CS6 64 PB15/TCLK3 100 PA19/MISOB 136 NOE/NRD 29 PB4/A22/CS5 65 PB16/TIOA3 101 PA20/MOSIB 137 NWE/NWR0 30 PB5/A23/CS4 66 PB17/TIOB3 102 PA21/NPCSB0/NSSB 138 NUB/NWR1 31 D0 67 PB18/TCLK4 103 PA22/NPCSB1 139 NCS0 32 D1 68 PB19/TIOA4 104 PA23/NPCSB2 140 NCS1 33 D2 69 PB20/TIOB4 105 PA24/NPCSB3 141 PB0/NCS2 34 D3 70 PB21/TCLK5 106 PA25/MCKO 142 PB1/NCS3 35 VDDCORE 71 VDDCORE 107 VDDCORE 143 VDDCORE 36 VDDIO 72 VDDIO 108 VDDIO 144 VDDIO 3 1779B–ATARM–03/02 Table 2. AT91M42800A Pinout in BGA 144 Package 4 Pin# Name Pin# Name Pin# Name Pin# Name A1 PB1/NCS3 D1 A2 G1 A17 K1 D1 A2 NCS0 D2 A3 G2 A16 K2 VDDCORE A3 NCS1 D3 A4 G3 A11 K3 VDDIO A4 GND D4 NWAIT G4 A13 K4 D9 A5 PLLRCB D5 PA29/PME G5 GND K5 D10 A6 GND D6 PA28 G6 GND K6 D14 A7 PLLRCA D7 TCK G7 GND K7 PB9/TCLK1 A8 GND D8 TMS G8 GND K8 PB13/TIOA2 A9 XOUT D9 MODE1 G9 PA9/TXD1/NTRI K9 PB11/TIOB1 A10 XIN D10 PA25/MCKO G10 PA10/RXD1 K10 VDDIO A11 MODE0 D11 PA21/NPCSB0 G11 PA8/SCK1 K11 PB16/TIOA3 A12 PA22/NPCSB1 D12 PA18/SPCKB G12 PA7/RXD0 K12 PB23/TIOB5 B1 NUB/NWR1 E1 A7 H1 A18 L1 D3 B2 PB0/NCS2 E2 VDDIO H2 VDDIO L2 D2 B3 VDDCORE E3 A6 H3 A15 L3 D5 B4 NWE/NWR0 E4 A5 H4 A14 L4 D8 B5 VDDPLL E5 GND H5 A19 L5 VDDIO B6 TDO E6 GND H6 GND L6 D13 B7 VDDPLL E7 GND H7 GND L7 PB8/TIOB0 B8 NWDOVF E8 NTRST H8 GND L8 VDDIO B9 PA26 E9 PA13/MOSIA H9 PA6/TXD0 L9 PB17/TIOB3 B10 PA19/MISOB E10 PA16/NPCSA2 H10 PA4/FIQ L10 VDDCORE B11 PA24/NPCSB3 E11 VDDIO H11 VDDIO L11 PB20/TIOB4 B12 PA23/NPCSB2 E12 PA17/NPCSA3 H12 PA5/SCK0 L12 PB22/TIOA5 C1 NLB/A0 F1 A8 J1 PB5/A23/CS4 M1 D4 C2 A1 F2 A12 J2 D0 M2 D6 C3 VDDIO F3 A9 J3 PB4/A22/CS5 M3 D7 C4 NOE/NRD F4 A10 J4 PB3/A21/CS6 M4 D11 C5 VDDIO F5 GND J5 PB2/A20/CS7 M5 D12 C6 NRST F6 GND J6 D15 M6 PB7/TIOA0 C7 TDI F7 GND J7 PB6/TCLK0 M7 PB12/TCLK2 C8 VDDIO F8 GND J8 PB10/TIOA1 M8 PB15/TCLK3 C9 PA27/BMS F9 PA12/MISOA J9 PA3/IRQ3 M9 PB14/TIOB2 C10 VDDIO F10 PA15/NPCSA1 J10 PA2/IRQ2 M10 PB18/TCLK4 C11 VDDCORE F11 PA11/SPCKA J11 PA0/IRQ0 M11 PB19/TIOA4 C12 PA20/MOSIB F12 PA14/NPCSA0 J12 PA1/IRQ1 M12 PB21/TCLK5 AT91M42800A 1779B–ATARM–03/02 AT91M42800A Pin Description Table 3. AT91M42800A Pin Description Module EBI AIC TC USART SPIA SPIB PIO ST CLOCK Test and Reset Name Function A0 - A23 Address Bus D0 - D15 Data Bus CS4 - CS7 Chip Select Type Active Level Output – I/O – Output High Comments All valid after reset A23 - A20 after reset NCS0 - NCS3 Chip Select Output Low NWR0 Lower Byte 0 Write Signal Output Low Used in Byte Write option NWR1 Lower Byte 1 Write Signal Output Low Used in Byte Write option NRD Read Signal Output Low Used in Byte Write option NWE Write Enable Output Low Used in Byte Select option NOE Output Enable Output Low Used in Byte Select option NUB Upper Byte Select (16-bit SRAM) Output Low Used in Byte Select option NLB Lower Byte Select (16-bit SRAM) Output Low Used in Byte Select option NWAIT Wait Input Input Low BMS Boot Mode Select Input – PME Protect Mode Enable Input High PIO-controlled after reset IRQ0 - IRQ3 External Interrupt Request Input – PIO-controlled after reset FIQ Fast External Interrupt Request Input – PIO-controlled after reset TCLK0 - TCLK5 Timer External Clock Input – PIO-controlled after reset TIOA0 - TIOA5 Multi-purpose Timer I/O Pin A I/O – PIO-controlled after reset TIOB0 - TIOB5 Multi-purpose Timer I/O Pin B I/O – PIO-controlled after reset SCK0 - SCK1 External Serial Clock I/O – PIO-controlled after reset TXD0 - TXD1 Transmit Data Output Output – PIO-controlled after reset Sampled during reset RXD0 - RXD1 Receive Data Input Input – PIO-controlled after reset SPCKA/SPCKB Clock I/O – PIO-controlled after reset MISOA/MISOB Master In Slave Out I/O – PIO-controlled after reset MOSIA/MOSIB Master Out Slave In NSSA/NSSB Slave Select NPCSA0 - NPCSA3 NPCSB0 - NPCSB3 Peripheral Chip Selects PA0 - PA29 Programmable I/O Port A PB0 - PB23 Programmable I/O Port B NWDOVF Watchdog Timer Overflow XIN Oscillator Input or External Clock XOUT Oscillator Output PLLRCA PLLRCB I/O – PIO-controlled after reset Input Low PIO-controlled after reset Output Low PIO-controlled after reset I/O – Input after reset I/O – Input after reset Output Low Input – Output – RC Filter for PLL A Input – RC Filter for PLL B Input – MCKO Clock Output Output – NRST Hardware Reset Input Input Low MODE0 - MODE1 Mode Selection Input Open drain Schmitt trigger 5 1779B–ATARM–03/02 Table 3. AT91M42800A Pin Description (Continued) Module JTAG/ICE Emulation Power 6 Name Function Type Active Level TMS Test Mode Select Input – Schmitt trigger, internal pull-up Input – Schmitt trigger, internal pull-up Output – Comments TDI Test Data In TDO Test Data Out TCK Test Clock Input – Schmitt trigger, internal pull-up NTRST Test Reset Input Input Low Schmitt trigger, internal pull-up NTRI Tri-state Mode Enable Input Low VDDIO I/O Power Power – 3V or 5V nominal supply Sampled during reset VDDCORE Core Power Power – 3V nominal supply VDDPLL PLL Power Power – 3V nominal supply GND Ground Ground – AT91M42800A 1779B–ATARM–03/02 AT91M42800A Block Diagram Figure 3. AT91M42800A MODE0 MODE1 NRST Reset Embedded ICE JTAG JTAG Selection NTRST TMS TDO TDI TCK D0-D15 ARM7TDMI Core A0/NLB A1-A19 NRD/NOE NWR0/NWE NWR1/NUB NWAIT NCS0 NCS1 XIN XOUT Internal RAM 8K Bytes Clock Generator PLLRCA PLLRCB EBI: External Bus Interface ASB PA27/BMS PA29/PME ASB Controller PA25/MCKO PA26 PA28 AMBA™ Bridge PA0/IRQ0 PA1/IRQ1 PA2/IRQ2 PA3/IRQ3 PA4/FIQ AIC: Advanced Interrupt Controller PA5/SCK0 PA6/TXD0 PA7/RXD0 PA8/SCK1 PA9/TXD1/NTRI PA10/RXD1 PA11/SPCKA PA12/MISOA PA13/MOSIA PA14/NPCSA0/NSSA PA15/NPCSA1 PA16/NPCSA2 PA17/NPCSA3 PA18/SPCKB PA19/MISOB PA20/MOSIB PA21/NPCSB0/NSSB PA22/NPCSB1 PA23/NPCSB2 PA24/NPCSB3 PB0/NCS2 PB1/NCS3 PB2/A20/CS7 PB3/A21/CS6 PB4/A22/CS5 PB5/A23/CS4 EBI User Interface USART0 2 PDC Channels USART1 2 PDC Channels TC: Timer/ Counter Block 0 APB P I O SPIB: Serial Peripheral Interface 2 PDC Channels 2 PDC Channels PB7/TIOA0 PB8/TIOB0 TC0 TC1 TC2 SPIA: Serial Peripheral Interface PB6/TCLK0 PB9/TCLK1 PB12/TCLK2 P I O PB10/TIOA1 PB11/TIOB1 PB13/TIOA2 PB14/TIOB2 TC: Timer/ Counter Block 1 PB15/TCLK3 PB18/TCLK4 PB21/TCLK5 TC3 PB16/TIOA3 PB17/TIOB3 TC4 PB19/TIOA4 PB20/TIOB4 TC5 PB22/TIOA5 PB23/TIOB5 System Timers PMC: Power Management Controller Watchdog NWDOVF Real-time Period Interval Chip ID PIO: Parallel I/O Controller 7 1779B–ATARM–03/02 Architectural Overview The AT91M42800A microcontroller integrates an ARM7TDMI with its embedded ICE interface, memories and peripherals. Its architecture consists of two main buses, the Advanced System Bus (ASB) and the Advanced Peripheral Bus (APB). Designed for maximum performance and controlled by the memory controller, the ASB interfaces the ARM7TDMI processor with the on-chip 32-bit memories, the External Bus Interface (EBI) and the AMBA™ Bridge. The AMBA Bridge drives the APB, which is designed for accesses to on-chip peripherals and optimized for low power consumption. The AT91M42800A microcontroller implements the ICE port of the ARM7TDMI processor on dedicated pins, offering a complete, low-cost and easy-to-use debug solution for target debugging. Memories The AT91M42800A microcontroller embeds up to 8K bytes of internal SRAM. The internal memory is directly connected to the 32-bit data bus and is single-cycle accessible. This provides maximum performance of 30 MIPS at 33 MHz by using the ARM instruction set of the processor. The on-chip memory significantly reduces the system power consumption and improves its performance over external memory solutions. The AT91M42800A microcontroller features an External Bus Interface (EBI), which enables connection of external memories and application-specific peripherals. The EBI supports 8- or 16-bit devices and can use two 8-bit devices to emulate a single 16-bit device. The EBI implements the early read protocol, enabling single clock cycle memory accesses two times faster than standard memory interfaces. Peripherals The AT91M42800A microcontroller integrates several peripherals, which are classified as system or user peripherals. All on-chip peripherals are 32-bit accessible by the AMBA Bridge, and can be programmed with a minimum number of instructions. The peripheral register set is composed of control, mode, data, status and enable/disable/status registers. An on-chip Peripheral Data Controller (PDC) transfers data between the on-chip USARTs/SPIs and the on- and off-chip memories without processor intervention. Most importantly, the PDC removes the processor interrupt handling overhead and significantly reduces the number of clock cycles required for a data transfer. It can transfer up to 64K continuous bytes without reprogramming the start address. As a result, the performance of the microcontroller is increased and the power consumption reduced. 8 AT91M42800A 1779B–ATARM–03/02 AT91M42800A System Peripherals The External Bus Interface (EBI) controls the external memory and peripheral devices via an 8- or 16-bit data bus and is programmed through the APB. Each chip select line has its own programming register. The Power Management Controller (PMC) optimizes power consumption of the product by controlling the clocking elements such as the oscillator and the PLLs, system and user peripheral clocks. The Advanced Interrupt Controller (AIC) controls the internal sources from the internal peripherals and the five external interrupt lines (including the FIQ) to provide an interrupt and/or fast interrupt request to the ARM7TDMI. It integrates an 8-level priority controller, and, using the Auto-vectoring feature, reduces the interrupt latency time. The Parallel Input/Output Controllers (PIOA, PIOB) controls up to 54 I/O lines. It enables the user to select specific pins for on-chip peripheral input/output functions, and generalpurpose input/output signal pins. The PIO controllers can be programmed to detect an interrupt on a signal change from each line. There are three embedded system timers. The Real-time Timer (RTT) counts elapsed seconds and can generate periodic or programmed interrupts. The Period Interval Timer (PIT) can be used as a user-programmable time-base, and can generate periodic ticks. The Watchdog (WD) can be used to prevent system lock-up if the software becomes trapped in a deadlock. The Special Function (SF) module integrates the Chip ID and the Reset Status registers. User Peripherals Two USARTs, independently configurable, enable communication at a high baud rate in synchronous or asynchronous mode. The format includes start, stop and parity bits and up to 9 data bits. Each USART also features a Time-out and a Time-guard register, facilitating the use of the two dedicated Peripheral Data Controller (PDC) channels. The two 3-channel, 16-bit Timer/Counters (TC) are highly-programmable and support capture or waveform modes. Each TC channel can be programmed to measure or generate different kinds of waves, and can detect and control two input/output signals. Each TC also has three external clock signals. Two independently configurable SPIs provide communication with external devices in master or slave mode. Each has four external chip selects which can be connected to up to 15 devices. The data length is programmable, from 8- to 16-bit. 9 1779B–ATARM–03/02 Associated Documentation Table 4. Associated Documentation Information Document Title Internal architecture of processor ARM/Thumb instruction sets Embedded in-circuit-emulator ARM7TDMI (Thumb) Datasheet External memory interface mapping Peripheral operations Peripheral user interfaces AT91M42800A Datasheet (this document) DC characteristics Power consumption Thermal and reliability chonsiderations AC characteristics AT91M42800A Electrical Characteristics Datasheet Product overview Ordering information Packaging information Soldering profile AT91M42800A Summary Datasheet 10 AT91M42800A 1779B–ATARM–03/02 AT91M42800A Product Overview Power Supply The AT91M42800A has three kinds of power supply pins: • VDDCORE pins that power the chip core • VDDIO pins that power the I/O lines • VDDPLL pins that power the oscillator and PLL cells VDDCORE and VDDIO pins allow core power consumption to be reduced by supplying it with a lower voltage than the I/O lines. The VDDCORE pins must never be powered at a voltage greater than the supply voltage applied to the VDDIO. The VDDPLL pin is used to supply the oscillator and both PLLs. The voltage applied on these pins is typically 3.3V, and it must not be lower than VDDCORE. Typical supported voltage combinations are shown in the following table: Pins Nominal Supply Voltages VDDCORE 3.3V 3.0V or 3.3V VDDIO 5.0V 3.0V or 3.3V VDDPLL 3.3V 3.0V or 3.3V Input/Output Considerations After the reset, the peripheral I/Os are initialized as inputs to provide the user with maximum flexibility. It is recommended that in any application phase, the inputs to the AT91M42800A microcontroller be held at valid logic levels to minimize the power consumption. Operating Modes The AT91M42800A has two pins dedicated to defining MODE0 and MODE1 operating modes. These pins allow the user to enter the device in Boundary Scan mode. They also allow the user to run the processor from the on-chip oscillator output and from an external clock by bypassing the on-chip oscillator. The last mode is reserved for test purposes. A chip reset must be performed (NRST and NTRST) after MODE0 and/or MODE1 have been changed. MODE0 MODE1 Operating Mode 0 0 Normal operating mode by using the on-chip oscillator 0 1 Boundary Scan Mode 1 0 Normal operating mode by using an external clock on XIN 1 1 Reserved for test Warning: The user must take the external oscillator frequency into account so that it is consistent with the minimum access time requested by the memory device used at the boot. Both the default EBI setting (zero wait state) on Chip Select 0 (See “Boot on NCS0” on page 28) and the minimum access time of the boot memory are two parameters that determine this maximum frequency of the external oscillator. Clock Generator The AT91M42800A microcontroller embeds a 32.768 kHz oscillator that generates the Slow Clock (SLCK). This on-chip oscillator can be bypassed by setting the correct logical level on the MODE0 and MODE1 pins, as shown above. In this case, SLCK equals XIN. 11 1779B–ATARM–03/02 The AT91M42800A microcontroller has a fully static design and works either on the Master Clock (MCK), generated from the Slow Clock by means of the two integrated PLLs, or on the Slow Clock (SLCK). These clocks are also provided as an output of the device on the pin MCKO, which is multiplexed with a general-purpose I/O line. While NRST is active, and after the reset, the MCKO is valid and outputs an image of the SLCK signal. The PIO Controller must be programmed to use this pin as standard I/O line. Reset Reset initializes the user interface registers to their default states as defined in the peripheral sections of this datasheet and forces the ARM7TDMI to perform the next instruction fetch from address zero. Except for the program counter, the ARM core registers do not have defined reset states. When reset is active, the inputs of the AT91M42800A must be held at valid logic levels. The EBI address lines drive low during reset. All the peripheral clocks are disabled during reset to save power. NRST Pin NRST is the active low reset input. It is asserted asynchronously, but exit from reset is synchronized internally to the slow clock (SLCK). At power-up, NRST must be active until the on-chip oscillator is stable. During normal operation, NRST must be active for a minimum of 10 SLCK clock cycles to ensure correct initialization. The pins BMS and NTRI are sampled during the 10 SLCK clock cycles just prior to the rising edge of NRST. The NRST pin has no effect on the on-chip Embedded ICE logic. Watchdog Reset The internally generated watchdog reset has the same effect as the NRST pin, except that the pins BMS and NTRI are not sampled. Boot mode and Tri-state mode are not updated. The NRST pin has priority if both types of reset coincide. Emulation Functions Tri-state Mode The AT91M42800A provides a Tri-state mode, which is used for debug purposes in order to connect an emulator probe to an application board. In Tri-state mode the AT91M42800A continues to function, but all the output pin drivers are tri-stated. To enter Tri-state mode, the pin NTRI must be held low during the last 10 SLCK clock cycles before the rising edge of NRST. For normal operation, the pin NTRI must be held high during reset, by a resistor of up to 400 kΩ. NTRI must be driven to a valid logic value during reset. NTRI is multiplexed with Parallel I/O PA9 and USART 1 serial data transmit line TXD1. Standard RS232 drivers generally contain internal 400 kΩ pull-up resistors. If TXD1 is connected to one of these drivers, this pull-up will ensure normal operation, without the need for an additional external resistor. Embedded ICE 12 ARM standard embedded in-circuit emulation is supported via the JTAG/ICE port. It is connected to a host computer via an embedded ICE Interface. Embedded ICE mode is selected when MODE1 is low. It is not possible to switch directly between ICE and JTAG operations. A chip reset must be performed (NRST and NTRST) after MODE0 and/or MODE1 have/has been changed. The reset input to the embedded ICE (NTRST) is provided separately to facilitate debug of boot programs. AT91M42800A 1779B–ATARM–03/02 AT91M42800A IEEE 1149.1 JTAG Boundary Scan IEEE 1149.1 JTAG Boundary Scan is enabled when MODE0 is low and MODE1 is high. The functions SAMPLE, EXTEST and BYPASS are implemented. In ICE Debug mode, the ARM core responds with a non-JTAG chip ID that identifies the core to the ICE system. This is not IEEE 1149.1 JTAG compliant. It is not possible to switch directly between JTAG and ICE operations. A chip reset must be performed (NRST and NTRST) after MODE0 and/or MODE1 have/has been changed. Memory Controller The ARM7TDMI processor address space is 4G bytes. The memory controller decodes the internal 32-bit address bus and defines three address spaces: • Internal Memories in the four lowest megabytes • Middle Space reserved for the external devices (memory or peripherals) controlled by the EBI • Internal Peripherals in the four highest megabytes In any of these address spaces, the ARM7TDMI operates in little-endian mode only. Protection Mode The embedded peripherals can be protected against unwanted access. The PME (Protect Mode Enable) pin must be tied high and validated in its peripheral operation (PIO Disable) to enable the protection mode. When enabled, any peripheral access must be done while the ARM7TDMI is running in Privileged mode (i.e., the accesses in user mode result in an abort). Only the valid peripheral address space is protected and requests to the undefined addresses will lead to a normal operation without abort. Internal Memories The AT91M42800A microcontroller integrates an 8-Kbyte primary internal SRAM. All internal memories are 32 bits wide and single-clock cycle accessible. Byte (8-bit), halfword (16-bit) or word (32-bit) accesses are supported and are executed within one cycle. Fetching Thumb or ARM instructions is supported and internal memory can store twice as many Thumb instructions as ARM ones. The SRAM bank is mapped at address 0x0 (after the remap command), and ARM7TDMI exception vectors between 0x0 and 0x20 that can be modified by the software. The rest of the bank can be used for stack allocation (to speed up context saving and restoring), or as data and program storage for critical algorithms. Boot Mode Select The ARM reset vector is at address 0x0. After the NRST line is released, the ARM7TDMI executes the instruction stored at this address. This means that this address must be mapped in non-volatile memory after the reset. The input level on the BMS pin during the last 10 SLCK clock cycles before the rising edge of the NRST selects the type of boot memory. The Boot mode depends on BMS (see Table 5). The pin BMS is multiplexed with the I/O line PA27 that can be programmed after reset like any standard PIO line. Table 5. Boot Mode Select BMS Remap Command Boot Memory 1 External 8-bit memory NCS0 0 External 16-bit memory on NCS0 The ARM vectors (Reset, Abort, Data Abort, Prefetch Abort, Undefined Instruction, Interrupt, Fast Interrupt) are mapped from address 0x0 to address 0x20. In order to allow these vectors to be redefined dynamically by the software, the AT91M42800A microcontroller uses a remap command that enables switching between the boot mem13 1779B–ATARM–03/02 ory and the internal SRAM bank addresses. The remap command is accessible through the EBI User Interface, by writing one in RCB of EBI_RCR (Remap Control Register). Performing a remap command is mandatory if access to the other external devices (connected to chip selects 1 to 7) is required. The remap operation can only be changed back by an internal reset or an NRST assertion. Notes: Abort Control 1. NIRQ de-assertion and automatic interrupt clearing if the source is programmed as level sensitive. The abort signal providing a Data Abort or a Prefetch Abort exception to the ARM7TDMI is asserted in the following cases: • When accessing an undefined address in the EBI address space • When the ARM7TDMI performs a misaligned access No abort is generated when reading the internal memory or by accessing the internal peripherals, whether the address is defined or not. When the processor performs a forbidden write access in a mode-protected peripheral register, the write is cancelled but no abort is generated. The processor can perform word or half-word data access with a misaligned address when a register relative load/store instruction is executed and the register contains a misaligned address. In this case, whether the access is in write or in read, an abort is generated but the access is not cancelled. The Abort Status Register traces the source that caused the last abort. The address and the type of abort are stored in registers of the External Bus Interface. External Bus Interface The External Bus Interface handles the accesses between addresses 0x0040 0000 and 0xFFC0 0000. It generates the signals that control access to the external devices, and can be configured from eight 1-Mbyte banks up to four 16-Mbyte banks. In all cases it supports byte, half-word and word aligned accesses. For each of these banks, the user can program: • Number of wait states • Number of data float times (wait time after the access is finished to prevent any bus contention in case the device takes too long in releasing the bus) • Data bus width (8-bit or 16-bit) • With a 16-bit wide data bus, the user can program the EBI to control one 16-bit device (Byte Access Select mode) or two 8-bit devices in parallel that emulate a 16-bit memory (Byte Write Access mode). The External Bus Interface features also the Early Read Protocol, configurable for all the devices, that significantly reduces access time requirements on an external device. 14 AT91M42800A 1779B–ATARM–03/02 AT91M42800A Peripherals The AT91M42800A peripherals are connected to the 32-bit wide Advanced Peripheral Bus. Peripheral registers are only word accessible. Byte and half-word accesses are not supported. If a byte or a half-word access is attempted, the memory controller automatically masks the lowest address bits and generates a word access. Each peripheral has a 16-Kbyte address space allocated (the AIC only has a 4-Kbyte address space). Peripheral Registers The following registers are common to all peripherals: • Control Register – Write-only register that triggers a command when a one is written to the corresponding position at the appropriate address. Writing a zero has no effect. • Mode Register – read/write register that defines the configuration of the peripheral. Usually has a value of 0x0 after a reset. • Data Registers – read and/or write register that enables the exchange of data between the processor and the peripheral. • Status Register – Read-only register that returns the status of the peripheral. • Enable/Disable/Status Registers are shadow command registers. Writing a one in the Enable Register sets the corresponding bit in the Status Register. Writing a one in the Disable Register resets the corresponding bit and the result can be read in the Status Register. Writing a bit to zero has no effect. This register access method maximizes the efficiency of bit manipulation, and enables modification of a register with a single non-interruptible instruction, replacing the costly read-modify-write operation. Unused bits in the peripheral registers are shown as “–” and must be written at 0 for upward compatibility. These bits read 0. Peripheral Interrupt Control The Interrupt Control of each peripheral is controlled from the status register using the interrupt mask. The status register bits are ANDed to their corresponding interrupt mask bits and the result is then ORed to generate the Interrupt Source signal to the Advanced Interrupt Controller. The interrupt mask is read in the Interrupt Mask Register and is modified with the Interrupt Enable Register and the Interrupt Disable Register. The enable/disable/status (or mask) makes it possible to enable or disable peripheral interrupt sources with a noninterruptible single instruction. This eliminates the need for interrupt masking at the AIC or Core level in real-time and multi-tasking systems. Peripheral Data Controller The AT91M42800A has an 8-channel PDC dedicated to the two on-chip USARTs and to the two on-chip SPIs. One PDC channel is connected to the receiving channel and one to the transmitting channel of each peripheral. The user interface of a PDC channel is integrated in the memory space of each USART channel and in the memory space of each SPI. It contains a 32-bit address pointer register and a 16-bit count register. When the programmed data is transferred, an end-oftransfer interrupt is generated by the corresponding peripheral. See the USART section and the SPI section for more details on PDC operation and programming. 15 1779B–ATARM–03/02 System Peripherals PMC: Power Management Controller The AT91M42800A’s Power Management Controller optimizes the power consumption of the device. The PMC controls the clocking elements such as the oscillator and the PLLs, and the System and the Peripheral Clocks. It also controls the MCKO pin and permits to the user to select four different signals to be driven on this pin. The AT91M42800A has the following clock elements: • The oscillator providing a clock that depends on the crystal fundamental frequency connected between the XIN and XOUT pins • PLL A providing a low-to-middle frequency clock range • PLL B providing a middle-to-high frequency range • The Clock prescaler • The ARM Processor Clock controller • The Peripheral Clock controller • The Master Clock Output controller The on-chip low-power oscillator together with the PLL-based frequency multiplier and the prescaler results in a programmable clock between 500 Hz and 66 MHz. It is the responsibility of the user to make sure that the PMC programming does not result in a clock over the acceptable limits. ST: System Timer The System Timer module integrates three different free-running timers: • A Period Interval Timer setting the base time for an Operating System. • A Watchdog Timer that is built around a 16-bit counter, and is used to prevent system lock-up if the software becomes trapped in a deadlock. It can generate an internal reset or interrupt, or assert an active level on the dedicated pin NWDOVF. • A Real-time Timer counting elapsed seconds. These timers count using the Slow Clock. Typically, this clock has a frequency of 32768 Hz. AIC: Advanced Interrupt Controller The AT91M42800A has an 8-level priority, individually maskable, vectored interrupt controller. This feature substantially reduces the software and real-time overhead in handling internal and external interrupts. The interrupt controller is connected to the NFIQ (fast interrupt request) and the NIRQ (standard interrupt request) inputs of the ARM7TDMI processor. The processor’s NFIQ line can only be asserted by the external fast interrupt request input: FIQ. The NIRQ line can be asserted by the interrupts generated by the on-chip peripherals and the external interrupt request lines: IRQ0 to IRQ3. The 8-level priority encoder allows the customer to define the priority between the different NIRQ interrupt sources. Internal sources are programmed to be level sensitive or edge triggered. External sources can be programmed to be positive or negative edge triggered or high- or lowlevel sensitive. PIO: Parallel I/O Controller 16 The AT91M42800A has 54 programmable I/O lines. I/O lines are multiplexed with an external signal of a peripheral to optimize the use of available package pins. These lines are controlled by two separate and identical PIO Controllers called PIOA and PIOB. Each PIO controller also provides an internal interrupt signal to the Advanced Interrupt Controller and insertion of a simple input glitch filter on any of the PIO pins. AT91M42800A 1779B–ATARM–03/02 AT91M42800A SF: Special Function The AT91M42800A provides registers that implement the following special functions. • Chip Identification • RESET Status User Peripherals USART: Universal Synchronous/ Asynchronous Receiver Transmitter TC: Timer/Counter The AT91M42800A provides two identical, full-duplex, universal synchronous/asynchronous receiver/transmitters that interface to the APB and are connected to the Peripheral Data Controller. The main features are: • Programmable Baud Rate Generator with External or Internal Clock, as well as Slow Clock • Parity, Framing and Overrun Error Detection • Line Break Generation and Detection • Automatic Echo, Local Loopback and Remote Loopback channel modes • Multi-drop mode: Address Detection and Generation • Interrupt Generation • Two Dedicated Peripheral Data Controller channels • 5-, 6-, 7-, 8- and 9-bit character length The AT91M42800A features two Timer/Counter blocks, each containing three identical 16-bit Timer/Counter channels. Each channel can be independently programmed to perform a wide range of functions including frequency measurement, event counting, interval measurement, pulse generation, delay timing and pulse-width modulation. Each Timer/Counter (TC) channel has 3 external clock inputs, 5 internal clock inputs, and 2 multi-purpose input/output signals that can be configured by the user. Each channel drives an internal interrupt signal that can be programmed to generate processor interrupts via the AIC (Advanced Interrupt Controller). The Timer/Counter block has two global registers that act upon all three TC channels. The Block Control Register allows the three channels to be started simultaneously with the same instruction. The Block Mode Register defines the external clock inputs for each Timer/Counter channel, allowing them to be chained. Each Timer/Counter block operates independently and has a complete set of block and channel registers. SPI: Serial Peripheral Interface The AT91M42800A includes two SPIs that provide communication with external devices in Master or Slave mode. They are independent, and are referred to by the letters A and B. Each SPI has four external chip selects that can be connected to up to 15 devices. The data length is programmable from 8- to 16-bit. 17 1779B–ATARM–03/02 Memory Map Figure 4. AT91M42800A Memory Map before Remap Command Address Function Size Protection(1) Abort Control On-chip Peripherals 4M Bytes Privileged Yes On-chip SRAM 1M Byte No No Reserved On-chip Device 1M Byte No No 1M Byte No No 1M Byte No No 0xFFFFFFFF 0xFFC00000 0xFFBFFFFF Reserved 0x00400000 0x003FFFFF 0x00300000 0x002FFFFF 0x00200000 0x001FFFFF Reserved On-chip Device 0x00100000 0x000FFFFF External Devices Selected by NCS0 0x00000000 Note: 18 1. The ARM core modes are defined in the ARM7TDMI Datasheet. Privileged is a non-user mode. The protection is active only if Protect mode is enabled. AT91M42800A 1779B–ATARM–03/02 AT91M42800A Figure 5. AT91M42800A Memory Map after Remap Command Address Size Protection(1) Abort Control 4M Bytes Privileged Yes External Devices (up to 8) Up to 8 Devices Programmable Page Size 1, 4, 16, 64M Bytes No Yes Reserved 1M Byte No No Reserved On-chip Device 1M Byte No No 1M Byte No No 1M Byte No No Function 0xFFFFFFFF On-chip Peripherals 0xFFC00000 0xFFBFFFFF 0x00400000 0x003FFFFF 0x00300000 0x002FFFFF 0x00200000 0x001FFFFF Reserved On-chip Device 0x00100000 0x000FFFFF On-chip RAM 0x00000000 Note: 1. The ARM core modes are defined in the ARM7TDMI Datasheet. Privileged is a non-user mode. The protection is active only if Protect mode is enabled. 19 1779B–ATARM–03/02 Peripheral Memory Map Figure 6. AT91M42800A Peripheral Memory Map Address Peripheral Peripheral Name Size Protection AIC Advanced Interrupt Controller 4K Bytes Privileged 0xFFFFFFFF 0xFFFFF000 0xFFFFEFFF 0xFFFFC000 Reserved 0xFFFFBFFF ST System Timer 16K Bytes Privileged PMC Power Management Controller 16K Bytes Privileged PIOB Parallel I/O Controller B 16K Bytes Privileged PIOA Parallel I/O Controller A 16K Bytes Privileged 0xFFFF8000 0xFFFF7FFF 0xFFFF4000 0xFFFF3FFF 0xFFFF0000 0xFFFEFFFF 0xFFFEC000 0xFFFEBFFF 0xFFFD8000 Reserved 0xFFFD7FFF TC1 Timer Counter 1 Channels 3, 4 and 5 16K Bytes Privileged TC0 Timer Counter 0 Channels 0,1 and 2 16K Bytes Privileged SPIB Serial Peripheral Interface B 16K Bytes Privileged SPIA Serial Peripheral Interface A 16K Bytes Privileged USART1 Universal Synchronous/ Asynchronous Receiver/Transmitter 1 16K Bytes Privileged USART0 Universal Synchronous/ Asynchronous Receiver/Transmitter 0 16K Bytes Privileged 16K Bytes Privileged 16K Bytes Privileged 0xFFFD4000 0xFFFD3FFF 0xFFFD0000 0xFFFCFFFF 0xFFFCC000 0xFFFCBFFF 0xFFFC8000 0xFFFC7FFF 0xFFFC4000 0xFFFC3FFF 0xFFFC0000 0xFFFBFFFF 0xFFF04000 Reserved 0xFFF03FFF SF Special Function 0xFFF00000 0xFFEFFFFF 0xFFF04000 Reserved 0xFFE03FFF EBI External Bus Interface 0xFFE00000 0xFFDFFFFF 0xFFD00000 Note: 20 Reserved 1. The ARM core modes are defined in the ARM7TDMI Datasheet. Privileged is a non-user mode. The protection is active only if Protect mode is enabled. AT91M42800A 1779B–ATARM–03/02 AT91M42800A EBI: External Bus Interface The EBI handles the access requests performed by the ARM core or the PDC. It generates the signals that control the access to the external memory or peripheral devices. The EBI is fully programmable and can address up to 64M bytes. It has eight chip selects and a 24-bit address bus, the upper four bits of which are multiplexed with a chip select. The 16-bit data bus can be configured to interface with 8- or 16-bit external devices. Separate read and write control signals allow for direct memory and peripheral interfacing. The EBI supports different access protocols allowing single clock cycle memory accesses. The main features are: • External memory mapping • Up to 8 chip select lines • 8- or 16-bit data bus • Byte write or byte select lines • Remap of boot memory • Two different read protocols • Programmable wait state generation • External wait request • Programmable data float time The EBI User Interface is described on page 48. External Memory Mapping The memory map associates the internal 32-bit address space with the external 24-bit address bus. The memory map is defined by programming the base address and page size of the external memories (see EBI User Interface registers EBI_CSR0 to EBI_CSR7). Note that A0 - A23 is only significant for 8-bit memory; A1 - A23 is used for 16-bit memory. If the physical memory device is smaller than the programmed page size, it wraps around and appears to be repeated within the page. The EBI correctly handles any valid access to the memory device within the page (see Figure 7). In the event of an access request to an address outside any programmed page, an abort signal is generated. Two types of abort are possible: instruction prefetch abort and data a bort. Th e corre spon din g exce ption vector ad dresse s are 0 x000 000 0C an d 0x00000010, respectively. It is up to the system programmer to program the error handling routine to use in case of an abort (see the ARM7TDMI datasheet for further information). The chip selects can be defined to the same base address and an access to the overlapping address space asserts both NCS lines. The Chip Select Register, having the smaller number, defines the characteristics of the external access and the behaviour of the control signals. 21 1779B–ATARM–03/02 Figure 7. External Memory Smaller than Page Size Base + 4M Bytes 1M Byte Device Hi Repeat 3 Low Base + 3M Bytes 1M Byte Device Memory Map Hi Repeat 2 Low Base + 2M Bytes 1M Byte Device Hi Repeat 1 Low Base + 1M Byte 1M Byte Device Hi Low Base Abort Status When an abort is generated, the EBI_AASR (Abort Address Status Register) and the EBI_ASR (Abort Status Register) provide the details of the source causing the abort. Only the last abort is saved and registers are left in the last abort status. After the reset, the registers are initialized to 0. The following are saved: In EBI_AASR: • The address at which the abort is generated In EBI_ASR: EBI Behavior During Internal Accesses 22 • Whether or not the processor has accessed an undefined address in the EBI address space • Whether or not the processor required an access at a misaligned address • The size of the access (byte, word or half-word) • The type of the access (read, write or code fetch) When the ARM core performs accesses in the internal memories or the embedded peripherals, the EBI signals behave as follows: • The address lines remain at the level of the last external access. • The data bus is tri-stated. • The control signals remain in an inactive state. AT91M42800A 1779B–ATARM–03/02 AT91M42800A Pin Description Table 6. External Bus Interface Pin Description Name Description Type A0 - A23 Address bus Output D0 - D15 Data bus NCS0 - NCS3 Active low chip selects Output CS4 - CS7 Active high chip selects Output NRD Read Enable Output NWR0 - NWR1 Lower and upper write enable Output NOE Output enable Output NWE Write enable Output NUB, NLB Upper and lower byte select Output NWAIT Wait request Input PME Protection Mode Enabled Input I/O Table 7. EBI Multiplexed Signals Multiplexed Signals Functions A23 - A20 CS4 - CS7 Allows from 4 to 8 chip select lines to be used A0 NLB 8- or 16-bit data bus NRD NOE Byte-write or byte select access NWR0 NWE Byte-write or byte select access NWR1 NUB Byte-write or byte select access 23 1779B–ATARM–03/02 Chip Select Lines The EBI provides up to eight chip select lines: • Chip select lines NCS0 - NCS3 are dedicated to the EBI (not multiplexed). • Chip select lines CS4 - CS7 are multiplexed with the top four address lines A23 A20. By exchanging address lines for chip select lines, the user can optimize the EBI to suit the external memory requirements: more external devices or larger address range for each device. The selection is controlled by the ALE field in EBI_MCR (Memory Control Register). The following combinations are possible: A20, A21, A22, A23 (configuration by default) A20, A21, A22, CS4 A20, A21, CS5, CS4 A20, CS6, CS5, CS4 CS7, CS6, CS5, CS4 Figure 8. Memory Connections for Four External Devices(1) NCS0 - NCS3 NCS3 NRD EBI NWRx A0 - A23 NCS2 NCS1 NCS0 D0 - D15 Memory Enable Memory Enable Memory Enable Memory Enable Output Enable Write Enable A0 - A23 8 or 16 Notes: 24 D0 - D15 or D0 - D7 1. For four external devices, the maximum address space per device is 16M bytes. AT91M42800A 1779B–ATARM–03/02 AT91M42800A Figure 9. Memory Connections for Eight External Devices(1) CS4 - CS7 NCS0 - NCS3 CS7 NRD EBI CS6 NWRx CS5 A0 - A19 CS4 D0 - D15 NCS3 NCS2 NCS1 NCS0 Memory Enable Memory Enable Memory Enable Memory Enable Memory Enable Memory Enable Memory Enable Memory Enable Output Enable Write Enable A0 - A19 8 or 16 Notes: D0 - D15 or D0 - D7 1. For eight external devices, the maximum address space per device is 1M byte. Data Bus Width A data bus width of 8 or 16 bits can be selected for each chip select. This option is controlled by the DBW field in the EBI_CSR (Chip Select Register) for the corresponding chip select. Figure 10 shows how to connect a 512K x 8-bit memory on NCS2. Figure 10. Memory Connection for an 8-bit Data Bus D0 - D7 D0 - D7 D8 - D15 A1 - A18 EBI A0 A1 - A18 A0 NWR1 NWR0 NRD NCS2 Write Enable Output Enable Memory Enable Figure 11 shows how to connect a 512K x 16-bit memory on NCS2. 25 1779B–ATARM–03/02 Figure 11. Memory Connection for a 16-bit Data Bus EBI D0 - D7 D0 - D7 D8 - D15 D8 - D15 A1 - A19 A0 - A18 NLB Low Byte Enable NUB High Byte Enable NWE Write Enable NOE Output Enable NCS2 Byte Write or Byte Select Access Memory Enable Each chip select with a 16-bit data bus can operate with one of two different types of write access: • Byte Write Access supports two byte write and a single read signal. • Byte Select Access selects upper and/or lower byte with two byte select lines, and separate read and write signals. This option is controlled by the BAT field in the EBI_CSR (Chip Select Register) for the corresponding chip select. Byte Write Access is used to connect 2 x 8-bit devices as a 16-bit memory page. • The signal A0/NLB is not used. • The signal NWR1/NUB is used as NWR1 and enables upper byte writes. • The signal NWR0/NWE is used as NWR0 and enables lower byte writes. • The signal NRD/NOE is used as NRD and enables half-word and byte reads. Figure 12 shows how to connect two 512K x 8-bit devices in parallel on NCS2. 26 AT91M42800A 1779B–ATARM–03/02 AT91M42800A Figure 12. Memory Connection for 2 x 8-bit Data Buses D0 - D7 D0 - D7 D8 - D15 EBI A1 - A19 A0 - A18 A0 NWR1 NWR0 Write Enable NRD Read Enable NCS2 Memory Enable D8 - D15 A0 - A18 Write Enable Read Enable Memory Enable Byte Select Access is used to connect 16-bit devices in a memory page. • The signal A0/NLB is used as NLB and enables the lower byte for both read and write operations. • The signal NWR1/NUB is used as NUB and enables the upper byte for both read and write operations. • The signal NWR0/NWE is used as NWE and enables writing for byte or half-word. • The signal NRD/NOE is used as NOE and enables reading for byte or half-word. Figure 13 shows how to connect a 16-bit device with byte and half-word access (e.g., 16-bit SRAM) on NCS2. Figure 13. Connection for a 16-bit Data Bus with Byte and Half-word Access EBI D0 - D7 D0 - D7 D8 - D15 D8 - D15 A1 - A19 A0 - A18 NLB Low Byte Enable NUB High Byte Enable NWE Write Enable NOE Output Enable NCS2 Memory Enable 27 1779B–ATARM–03/02 Figure 14 shows how to connect a 16-bit device without byte access (e.g., Flash) on NCS2. Figure 14. Connection for a 16-bit Data Bus without Byte Write Capability EBI D0 - D7 D0 - D7 D8 - D15 D8 - D15 A1 - A19 A0 - A18 NLB NUB NWE Write Enable NOE Output Enable NCS2 Boot on NCS0 Memory Enable Depending on the device and the BMS pin level during the reset, the user can select either an 8-bit or 16-bit external memory device connected on NCS0 as the Boot memory. In this case, EBI_CSR0 (Chip Select Register 0) is reset at the following configuration for chip select 0: • 0 wait states (WSE = 0, NWS = 7) • 8-bit or 16-bit data bus width, depending on BMS Byte access type and number of data float time are set to Byte Write Access and 0, respectively. Before the remap command, the user can modify the chip select 0 configuration, programming the EBI_CSR0 with the exact Boot memory characteristics. The base address becomes effective after the remap command. Warning: In the internal oscillator bypass mode described in “Operating Modes” on page 11, the user must take the external oscillator frequency into account according to the minimum access time on the boot memory device. As illustration, the following table gives examples of oscillator frequency limits according to the time access without using NWAIT pin at the boot. Chip Select Assertion to Output Data Valid Maximum Delay in Read Cycle (tCE in ns) 110 7 90 9 70 11 55 14 25 24 Note: 28 External Oscillator Frequency Limit (MHz) Values take only tCE into account. AT91M42800A 1779B–ATARM–03/02 AT91M42800A Read Protocols The EBI provides two alternative protocols for external memory read access: standard and early read. The difference between the two protocols lies in the timing of the NRD (read cycle) waveform. The protocol is selected by the DRP field in EBI_MCR (Memory Control Register) and is valid for all memory devices. Standard read protocol is the default protocol after reset. Note: Standard Read Protocol In the following waveforms and descriptions, NRD represents NRD and NOE since the two signals have the same waveform. Likewise, NWE represents NWE, NWR0 and NWR1 unless NWR0 and NWR1 are otherwise represented. ADDR represents A0 - A23 and/or A1 - A23. Standard read protocol implements a read cycle in which NRD and NWE are similar. Both are active during the second half of the clock cycle. The first half of the clock cycle allows time to ensure completion of the previous access as well as the output of address and NCS before the read cycle begins. During a standard read protocol, external memory access, NCS is set low and ADDR is valid at the beginning of the access while NRD goes low only in the second half of the master clock cycle to avoid bus conflict (see Figure 15). Figure 15. Standard Read Protocol MCKI ADDR NCS NRD or NWE NWE is the same in both protocols. NWE always goes low in the second half of the master clock cycle (see Figure 17). 29 1779B–ATARM–03/02 Early Read Protocol Early read protocol provides more time for a read access from the memory by asserting NRD at the beginning of the clock cycle. In the case of successive read cycles in the same memory, NRD remains active continuously. Since a read cycle normally limits the speed of operation of the external memory system, early read protocol can allow a faster clock frequency to be used. However, an extra wait state is required in some cases to avoid contentions on the external bus. Figure 16. Early Read Protocol MCKI ADDR NCS NRD or NWE Early Read Wait State In early read protocol, an early read wait state is automatically inserted when an external write cycle is followed by a read cycle to allow time for the write cycle to end before the subsequent read cycle begins (see Figure 17). This wait state is generated in addition to any other programmed wait states (i.e., data float wait). No wait state is added when a read cycle is followed by a write cycle, between consecutive accesses of the same type or between external and internal memory accesses. Early read wait states affect the external bus only. They do not affect internal bus timing. Figure 17. Early Read Wait State Write Cycle Early Read Wait Read Cycle MCKI ADDR NCS NRD NWE 30 AT91M42800A 1779B–ATARM–03/02 AT91M42800A Write Data Hold Time During write cycles in both protocols, output data becomes valid after the falling edge of the NWE signal and remains valid after the rising edge of NWE, as illustrated in Figure 18. The external NWE waveform (on the NWE pin) is used to control the output data timing to guarantee this operation. It is therefore necessary to avoid excessive loading of the NWE pins, which could delay the write signal too long and cause a contention with a subsequent read cycle in standard protocol. Figure 18. Data Hold Time MCKI ADDR NWE Data Output In early read protocol the data can remain valid longer than in standard read protocol due to the additional wait cycle which follows a write access. 31 1779B–ATARM–03/02 Wait States Standard Wait States The EBI can automatically insert wait states. The different types of wait states are listed below: • Standard wait states • Data float wait states • External wait states • Chip select change wait states • Early Read wait states (as described in “Read Protocols” on page 29) Each chip select can be programmed to insert one or more wait states during an access on the corresponding device. This is done by setting the WSE field in the corresponding EBI_CSR. The number of cycles to insert is programmed in the NWS field in the same register. Below is the correspondence between the number of standard wait states programmed and the number of cycles during which the NWE pulse is held low: 0 wait states 1/2 cycle 1 wait state 1 cycle For each additional wait state programmed, an additional cycle is added. Figure 19. One Wait State Access 1 Wait State Access MCKI ADDR NCS NWE NRD Notes: 32 (1) (2) 1. Early Read Protocol 2. Standard Read Protocol AT91M42800A 1779B–ATARM–03/02 AT91M42800A Data Float Wait State Some memory devices are slow to release the external bus. For such devices, it is necessary to add wait states (data float waits) after a read access before starting a write access or a read access to a different external memory. The data float output time (tDF) for each external memory device is programmed in the TDF field of the EBI_CSR register for the corresponding chip select. The value (0 - 7 clock cycles) indicates the number of data float waits to be inserted and represents the time allowed for the data output to go high impedance after the memory is disabled. Data float wait states do not delay internal memory accesses. Hence, a single access to an external memory with long tDF will not slow down the execution of a program from internal memory. The EBI keeps track of the programmed external data float time during internal accesses, to ensure that the external memory system is not accessed while it is still busy. Internal memory accesses and consecutive accesses to the same external memory do not have added data float wait states. Figure 20. Data Float Output Time MCKI ADDR NCS NRD (1) (2) tDF D0-D15 Notes: 1. Early Read Protocol 2. Standard Read Protocol 33 1779B–ATARM–03/02 External Wait The NWAIT input can be used to add wait states at any time. NWAIT is active low and is detected on the rising edge of the clock. If NWAIT is low at the rising edge of the clock, the EBI adds a wait state and changes neither the output signals nor its internal counters and state. When NWAIT is deasserted, the EBI finishes the access sequence. The NWAIT signal must meet setup and hold requirements on the rising edge of the clock. Figure 21. External Wait MCKI ADDR NWAIT NCS NWE NRD Notes: 34 (1) (2) 1. Early Read Protocol 2. Standard Read Protocol AT91M42800A 1779B–ATARM–03/02 AT91M42800A Chip Select Change Wait States A chip select wait state is automatically inserted when consecutive accesses are made to two different external memories (if no wait states have already been inserted). If any wait states have already been inserted, (e.g., data float wait) then none are added. Figure 22. Chip Select Wait Mem 1 Chip Select Wait Mem 2 MCKI NCS1 NCS2 NRD (1) (2) NWE Notes: 1. Early Read Protocol 2. Standard Read Protocol 35 1779B–ATARM–03/02 Memory Access Waveforms Figures 23 through 26 show examples of the two alternative protocols for external memory read access. 36 D0 - D15 (Mem 2) D0 - D15 (AT91) D0 - D15 (Mem1) NCS2 NCS1 NWE NRD A0-A23 MCKI Read Mem 1 Write Mem 1 tWHDX Read Mem 1 chip select change wait Read Mem 2 Write Mem 2 tWHDX Read Mem 2 Figure 23. Standard Read Protocol without tDF AT91M42800A 1779B–ATARM–03/02 1779B–ATARM–03/02 Write Mem 1 Early Read Wait Cycle Read Mem 1 Read Mem 2 Write Mem 2 Early Read Wait Cycle Read Mem 2 MCKI A0 - A23 NRD NWE NCS1 Figure 24. Early Read Protocol without tDF Read Mem 1 Chip Select Change Wait NCS2 D0 - D15 (AT91) Long tWHDX D0 - D15 (Mem 2) long tWHDX 37 AT91M42800A D0 - D15 (Mem 1) 38 Write Mem 1 Read Mem 1 Data Float Wait Read Mem 2 Read Mem 2 Data Float Wait MCKI A0 - A23 NRD NWE NCS1 NCS2 tDF tDF D0 - D15 (Mem 1) 1779B–ATARM–03/02 D0 - D15 (AT91) tWHDX D0 - 15 (Mem 2) tDF Write Mem 2 Write Mem 2 Write Mem 2 Figure 25. Standard Read Protocol with tDF AT91M42800A Read Mem 1 Data Float Wait 1779B–ATARM–03/02 Write Mem 1 Early Read Wait Read Mem 1 Data Float Wait Read Mem 2 Read Mem 2 Data Float Wait MCKI A0 - A23 NRD Write Mem 2 Write Mem 2 Write Mem 2 Figure 26. Early Read Protocol with tDF Read Mem 1 Data Float Wait NWE NCS1 NCS2 tDF D0 - D15 (Mem 1) D0 - D15 (AT91) tWHDX D0 - D15 (Mem 2) tDF 39 AT91M42800A tDF Figures 27 through 33 show the timing cycles and wait states for read and write access to the various AT91M42800A external memory devices. The configurations described are shown in the following table: Table 8. Memory Access Waveforms 40 Figure Number Number of Wait States Bus Width Size of Data Transfer 27 0 16 Word 28 1 16 Word 29 1 16 Half-word 30 0 8 Word 31 1 8 Half-word 32 1 8 Byte 33 0 16 Byte AT91M42800A 1779B–ATARM–03/02 AT91M42800A Figure 27. 0 Wait States, 16-bit Bus Width, Word Transfer MCKI A1 - A23 ADDR+1 ADDR NCS NLB NUB READ ACCESS · Standard Protocol NRD D0 - D15 B2 B1 Internal Bus B 4 B3 X X B 2 B1 B4 B 3 B2 B 1 · Early Protocol NRD D0 - D15 B 2 B1 B 4 B3 WRITE ACCESS · Byte Write/ Byte Select Option NWE D0 - D15 B2 B 1 B 4 B3 41 1779B–ATARM–03/02 Figure 28. 1 Wait State, 16-bit Bus Width, Word Transfer 1 Wait State 1 Wait State MCKI A1 - A23 ADDR+1 ADDR NCS NLB NUB READ ACCESS · Standard Protocol NRD D0 - D15 B2 B 1 Internal Bus B4 B 3 X X B2 B1 B4 B 3 B2 B 1 · Early Protocol NRD D0 - D15 B2B1 B4B3 WRITE ACCESS · Byte Write/ Byte Select Option NWE D0 - D15 42 B2B1 B4B3 AT91M42800A 1779B–ATARM–03/02 AT91M42800A Figure 29. 1 Wait State, 16-bit Bus Width, Half-word Transfer 1 Wait State MCKI A1 - A23 NCS NLB NUB READ ACCESS · Standard Protocol NRD D0 - D15 Internal Bus B2 B1 X X B 2 B1 · Early Protocol NRD D0 - D15 B2 B1 WRITE ACCESS · Byte Write/ Byte Select Option NWE D0 - D15 B 2 B1 43 1779B–ATARM–03/02 Figure 30. 0 Wait States, 8-bit Bus Width, Word Transfer MCKI A0 - A23 ADDR+1 ADDR ADDR+2 ADDR+3 NCS READ ACCESS · Standard Protocol NRD D0 - D15 Internal Bus X B1 X B2 X B3 X B4 X X X B1 X X B 2 B1 X B 3 B2 B 1 B 4 B 3 B2 B 1 X B1 X B2 X B3 X B4 · Early Protocol NRD D0 - D15 WRITE ACCESS NWR0 NWR1 D0 - D15 44 X B1 X B2 X B3 X B4 AT91M42800A 1779B–ATARM–03/02 AT91M42800A Figure 31. 1 Wait State, 8-bit Bus Width, Half-word Transfer 1 Wait State 1Wait State MCKI A0 - A23 ADDR ADDR+1 NCS READ ACCESS · Standard Protocol NRD D0 - D15 X B1 Internal Bus X B2 X X X B1 X X B 2 B1 · Early Protocol NRD D0 - D15 X B1 X B2 WRITE ACCESS NWR0 NWR1 D0 - D15 X B1 X B2 45 1779B–ATARM–03/02 Figure 32. 1 Wait State, 8-bit Bus Width, Byte Transfer 1 Wait State MCKI A0 - A23 NCS READ ACCESS · Standard Protocol NRD D0 - D15 XB1 Internal Bus X X X B1 · Early Protocol NRD D0 - D15 X B1 WRITE ACCESS NWR0 NWR1 D0 - D15 46 X B1 AT91M42800A 1779B–ATARM–03/02 AT91M42800A Figure 33. 0 Wait States, 16-bit Bus Width, Byte Transfer MCKI A1 - A23 ADDR X X X 0 ADDR X X X 0 Internal Address ADDR X X X 0 ADDR X X X 1 NCS NLB NUB READ ACCESS · Standard Protocol NRD D0 - D15 X B1 B2X X X X B1 Internal Bus X X B2X · Early Protocol NRD D0 - D15 XB1 B2X B1B1 B2B2 WRITE ACCESS · Byte Write Option NWR0 NWR1 D0 - D15 · Byte Select Option NWE 47 1779B–ATARM–03/02 EBI User Interface The EBI is programmed using the registers listed in Table 9. The Remap Control Register (EBI_RCR) controls exit from Boot mode (see “Boot on NCS0” on page 28). The Memory Control Register (EBI_MCR) is used to program the number of active chip selects and data read protocol. Eight Chip Select Registers (EBI_CSR0 to EBI_CSR7) are used to program the parameters for the individual external memories. Each EBI_CSR must be programmed with a different base address, even for unused chip selects. The Abort Status registers indicate the access address (EBI_AASR) and the reason for the abort (EBI_ASR). Base Address: 0xFFE00000 (Code Label EBI_BASE) Table 9. EBI Memory Map Offset Name Access Reset State 0x00 Chip Select Register 0 EBI_CSR0 Read/Write 0x0000203E(1) 0x0000203D(2) 0x04 Chip Select Register 1 EBI_CSR1 Read/Write 0x10000000 0x08 Chip Select Register 2 EBI_CSR2 Read/Write 0x20000000 0x0C Chip Select Register 3 EBI_CSR3 Read/Write 0x30000000 0x10 Chip Select Register 4 EBI_CSR4 Read/Write 0x40000000 0x14 Chip Select Register 5 EBI_CSR5 Read/Write 0x50000000 0x18 Chip Select Register 6 EBI_CSR6 Read/Write 0x60000000 0x1C Chip Select Register 7 EBI_CSR7 Read/Write 0x70000000 0x20 Remap Control Register EBI_RCR Write-only – 0x24 Memory Control Register EBI_MCR Read/Write 0 0x28 Reserved – – – 0x2C Reserved – – – 0x30 Abort Status Register EBI_ASR Read-only 0x0 0x34 Address Abort Status Register EBI_AASR Read-only 0x0 Notes: 48 Register 1. 8-bit boot (if BMS is detected high) 2. 16-bit boot (if BMS is detected low) AT91M42800A 1779B–ATARM–03/02 AT91M42800A EBI Chip Select Register Register Name: Access Type: Reset Value: Absolute Address: 31 EBI_CSR0 - EBI_CSR7 Read/Write See Table 9 0xFFE00000 - 0xFFE0001C 30 29 28 27 26 25 24 19 18 17 16 – – – – 10 9 BA 23 22 21 20 BA 15 14 13 12 – – CSEN BAT 7 6 5 4 PAGES – WSE 11 8 TDF 3 2 PAGES 1 NWS 0 DBW • DBW: Data Bus Width DBW Data Bus Width Code Label: EBI_DBW 0 0 Reserved – 0 1 16-bit data bus width EBI_DBW_16 1 0 8-bit data bus width EBI_DBW_8 1 1 Reserved – Number of Standard Wait States Code Label: EBI_NWS • NWS: Number of Wait States This field is valid only if WSE is set. NWS 0 0 0 1 EBI_NWS_1 0 0 1 2 EBI_NWS_2 0 1 0 3 EBI_NWS_3 0 1 1 4 EBI_NWS_4 1 0 0 5 EBI_NWS_5 1 0 1 6 EBI_NWS_6 1 1 0 7 EBI_NWS_7 1 1 1 8 EBI_NWS_8 • WSE: Wait State Enable (Code Label EBI_WSE) 0 = Wait state generation is disabled. No wait states are inserted. 1 = Wait state generation is enabled. 49 1779B–ATARM–03/02 • PAGES: Page Size PAGES Page Size Active Bits in Base Address Code Label: EBI_PAGES 0 0 1M Byte 12 Bits (31 - 20) EBI_PAGES_1M 0 1 4M Bytes 10 Bits (31 - 22) EBI_PAGES_4M 1 0 16M Bytes 8 Bits (31 - 24) EBI_PAGES_16M 1 1 64M Bytes 6 Bits (31 - 26) EBI_PAGES_64M Number of Cycles Added after the Transfer Code Label: EBI_TDF • TDF: Data Float Output Time TDF • 0 0 0 0 EBI_TDF_0 0 0 1 1 EBI_TDF_1 0 1 0 2 EBI_TDF_2 0 1 1 3 EBI_TDF_3 1 0 0 4 EBI_TDF_4 1 0 1 5 EBI_TDF_5 1 1 0 6 EBI_TDF_6 1 1 1 7 EBI_TDF_7 BAT: Byte Access Type BAT Selected BAT Code Label: EBI_BAT 0 Byte-write access type EBI_BAT_BYTE_WRITE 1 Byte-select access type EBI_BAT_BYTE_SELECT • CSEN: Chip Select Enable (Code Label EBI_CSEN) 0 = Chip select is disabled. 1 = Chip select is enabled. • BA: Base Address (Code Label EBI_BA) These bits contain the highest bits of the base address. If the page size is larger than 1M byte, the unused bits of the base address are ignored by the EBI decoder. 50 AT91M42800A 1779B–ATARM–03/02 AT91M42800A EBI Remap Control Register Register Name: EBI_RCR Access Type: Write-only Absolute Address: 0xFFE00020 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – RCB • RCB: Remap Command Bit (Code Label EBI_RCB) 0 = No effect. 1 = Cancels the remapping (performed at reset) of the page zero memory devices. EBI Memory Control Register Register Name: Access Type: Reset Value: Absolute Address: EBI_MCR Read/Write See Table 9 0xFFE00024 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – DRP – ALE • ALE: Address Line Enable This field determines the number of valid address lines and the number of valid chip select lines. ALE Valid Address Bits Maximum Addressable Space Valid Chip Select Code Label: EBI_ALE 0 X X A20, A21, A22, A23 16M Bytes None EBI_ALE_16M 1 0 0 A20, A21, A22 8M Bytes CS4 EBI_ALE_8M 1 0 1 A20, A21 4M Bytes CS4, CS5 EBI_ALE_4M 1 1 0 A20 2M Bytes CS4, CS5, CS6 EBI_ALE_2M 1 1 1 None 1M Byte CS4, CS5, CS6, CS7 EBI_ALE_1M 51 1779B–ATARM–03/02 • DRP: Data Read Protocol DRP 52 Selected DRP Code Label: EBI_DRP 0 Standard read protocol for all external memory devices enabled EBI_DRP_STANDARD 1 Early read protocol for all external memory devices enabled EBI_DRP_EARLY AT91M42800A 1779B–ATARM–03/02 AT91M42800A Abort Status Register Register Name: Access Type: Offset: Reset Value: EBI_ASR Read-only 0x30 0x0 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 – – PDC ARM 7 6 5 4 3 2 1 0 – – – – – – MISADD UNDADD ABTTYP 8 ABTSZ • UNDADD: Undefined Address Abort Status 0 = The last abort is not due to the access of an undefined address in the EBI address space. 1 = The last abort is due to the access of an undefined address in the EBI address space. • MISADD: Misaligned Address Abort Status 0 = During the last aborted access, the address required by the core was not unaligned. 1 = During the last aborted access, the address required by the core was unaligned. • ABTSZ: Abort Size Status This bit provides the size of the aborted access required by the core. ABTSZ Abort Size 0 0 Byte 0 1 Half-word 1 0 Word 1 1 Reserved • ABTTYP: Abort Type Status This bit provides the type of the aborted access required by the core. ABTTYP Abort Size 0 0 Data read 0 1 Data write 1 0 Code fetch 1 1 Reserved • ARM: Abort Induced by the ARM Core 0 = The last abort is not due to the ARM core. 1 = The last abort is due to the ARM core. • PDC: Abort Induced by the Peripheral Data Controller 0 = The last abort is not due to the Peripheral Data controller. 1 = The last abort is due to the Peripheral Data controller. 53 1779B–ATARM–03/02 Abort Address Status Register Register Name: Access Type: Offset: Reset Value: 31 EBI_AASR Read-only 0x34 0x0 30 29 28 27 26 25 24 19 18 17 16 11 10 9 8 3 2 1 0 ABTADD 23 22 21 20 ABTADD 15 14 13 12 ABTADD 7 6 5 4 ABTADD • ABTADD: Abort Address This field contains the address required by the last aborted access. 54 AT91M42800A 1779B–ATARM–03/02 AT91M42800A PMC: Power Management Controller The AT91M42800A’s Power Management Controller optimizes the power consumption of the device. The PMC controls the clocking elements such as the oscillator and the PLLs, and the System and the Peripheral Clocks. It also controls the MCKO pin and enables the user to select four different signals to be driven on this pin. The AT91M42800A has the following clock elements: • The oscillator, which provides a clock that depends on the crystal fundamental frequency connected between the XIN and XOUT pins • PLL A, which provides a low-to-middle frequency clock range • PLL B, which provides a middle-to-high frequency range • The Clock prescaler • The System Clock controller • The Peripheral Clock controller • The Master Clock Output controller The on-chip low-power oscillator together with the PLL-based frequency multiplier and the prescaler results in a programmable clock between 500 Hz and 66 MHz. It is the responsibility of the user to make sure that the PMC programming does not result in a clock over the acceptable limits. Figure 34. Oscillator, PLL and Clock Sources XIN XOUT 32 kHz Oscillator Slow Clock (SLCK) Main Clock (MCK) ARM Core Clock PLLRCA PLLA PLLRCB PLLB Power Management Controller Peripheral Clocks User Interface APB Bus 55 1779B–ATARM–03/02 Oscillator and Slow Clock The integrated oscillator generates the Slow Clock. It is designed for use with a 32.768 kHz fundamental crystal. A 38.4 kHz crystal can be used. The bias resistor is on-chip and the oscillator integrates an equivalent load capacitance equal to 10 pF. Figure 35. Slow Clock XIN 32 kHz Oscillator XOUT SLCK Slow Clock To operate correctly, the crystal must be as close to the XIN and XOUT pins as possible. An external variable capacitor can be added to adjust the oscillator frequency. Figure 36. Crystal Location GND GROUND PLANE C XIN XOUT Master Clock The Master Clock (MCK) is generated from the Slow Clock by means of one of the two integrated PLLs and the prescaler. Figure 37. Master Clock MUL PLLCOUNT PLLRCA PLLA PLL Lock Timer PLLS(1) Lock MUL CSS PLLRCB PRES PLLB SLCK Slow Clock Note: 56 Prescaler Source Clock MCK Master Clock 1. Value written at reset and not subsequently programmable. AT91M42800A 1779B–ATARM–03/02 AT91M42800A Phase Locked Loops Two PLLs are integrated in the AT91M42800A in order to cover a larger frequency range. Both PLLs have a Slow Clock input and a dedicated pin (PLLRCA or PLLRCB), which must have appropriate capacitors and resistors. The capacitors and resistors serve as a second order filter. The PLLRC pin (A or B) that corresponds to the PLL that is disabled may be grounded if capacitors and resistors need to be saved. Figure 38. PLL Capacitors and Resistors PLLRC PLL R C2 C GND Typical values for the two PLLs are shown below: PLLA: FSCLK = 32.768 kHz Fout_PLLA = 16.776 MHz R = 1600 Ohm C = 100 nF C2 = 10 nF With these parameters, the output frequency is stable (±10%) in 600 µs. This settling time is the value to be programmed in the PLLCOUNT field of PMC_CGMR. The maximum frequency overshoot during this phase is 22.5 MHz. PLLB: FSCLK = 32.768 kHz Fout_PLLB = 33.554 MHz R = 800 Ohm C = 1 µF C2 = 100 nF With these parameters, the output frequency is stable (±10%) in 4 ms. This settling time is the value to be programmed in the PLLCOUNT field of PMC_CGMR. The maximum frequency overshoot during this phase is 38 MHz. PLL Selection The required PLL must be selected at the first writing access and cannot be changed after that. The PLLS bit in PMC_CGMR (Clock Generator Mode Register) determines which PLL module is activated. The other PLL is disabled in order to reduce power consumption and can only be activated by another reset. Writing in PMC_CGMR with a different value has no effect. 57 1779B–ATARM–03/02 Source Clock Selection The bit CSS in PMC_CGMR selects the Slow Clock or the output of the activated PLL as the Source Clock of the prescaler. After reset, the CSS field is 0, selecting the Slow Clock as Source Clock. When switching from Slow Clock to PLL Output, the Source Clock takes effect after 3 Slow Clock cycles plus 2.5 PLL output signal cycles. This is a maximum value. When switching from PLL Output to Slow Clock, the switch takes effect after 3.5 Slow Clock cycles plus 2.5 PLL output signal cycles. This is a maximum value. PLL Programming Once the PLL is selected, the output of the active PLL is a multiple of the Slow Clock, determined by the MUL field of the PMC_CGMR. The value of the multiply factor can be up to 2048. The multiplication factor is the programmed value plus one (MUL+1). Each time PMC_CGMR is written with a MUL value different from the existing one, the LOCK bit in PMC_SR is automatically cleared and the PLL Lock Timer is started (see PLL Lock Timer). The LOCK bit is set when the PLL Lock Timer reaches 0. If a null value is programmed in the MUL field, the PLL is automatically disabled and bypassed to save power. The LOCK bit in PMC_SR is also automatically cleared. The time during which the LOCK bit is cleared is user programmable in the field PLLCOUNT in PMC_CGMR. The user must load this parameter with a value depending on the active PLL and its start-up time or the frequency shift performed. As long as the LOCK bit is 0, the PLL is automatically bypassed and its output is the Slow Clock. This means: PLL Lock Timer • A switch from the PLL output to the Slow Clock and the associated delays, when the PLL is locked. • A switch from the Slow Clock to the PLL output and the associated delays, when the LOCK bit is set. The Power Management Controller of the AT91M42800A integrates a dedicated 8-bit timer for the locking time of the PLL. This timer is loaded with the value written in PLLCOUNT each time the value in the field MUL changes. At the same time, the LOCK bit in PMC_SR is cleared, and the PLL is bypassed. The timer counts down the value written in PLLCOUNT on the Slow Clock. The countdown value ranges from 30 µs to 7.8 ms. When the PLL Lock Timer reaches 0, the LOCK bit is set and can provide an interrupt. The PLLCOUNT field is defined by the user, and depends on the current state of the PLL (unlocked or locked), the targeted output frequency and the filter implemented on the PLLRC pin. Prescaler The Clock Source (Slow Clock or PLL output) selected through the CSS field (Clock Source Select) in PMC_CGMR can be divided by 1, 2, 4, 8, 16, 32 or 64. The default divider after a reset is 1. The output of the prescaler is called Master Clock (MCK). When the prescaler value is modified, the new defined Master Clock is effective after a maximum delay of 64 Source Clock cycles. 58 AT91M42800A 1779B–ATARM–03/02 AT91M42800A Master Clock Output Controller The clock output on MCKO pin can be selected to be the Slow Clock, the Master Clock, the Master Clock inverted or the Master Clock divided by two through the MCKOSS field (Master Clock Output Source Select) in PMC_CGMR. The MCKO pad can be put in Tristate mode to save power consumption by setting the bit MCKODS (Master Clock Output Disable) in PMC_CGMR. After a reset the MCKO pin is enabled and is driven by the Slow Clock. Figure 39. Master Clock Output MCKOSS SLCK Slow Clock MCKODS MCKO Master Clock Output MCK Master Clock ARM Processor Clock Controller Divide by 2 The AT91M42800A has only one System Clock. It can be enabled and disabled by writing the System Clock Enable (PMC_SCER) and System Clock Disable Registers (PMC_SCDR). The status of this clock (at least for debug purpose) can be read in the System Clock Status Register (PMC_SCSR). The system clock is enabled after a reset and is automatically re-enabled by any enabled interrupt. When the system clock is disabled, the current instruction is finished before the clock is stopped. Note: Stopping the ARM core does not prevent PDC transfers. Figure 40. System Clock Control PMC_SCDR Set PMC_SCSR Idle Mode Register NIRQ NFIQ System Clock Clear MCK Master Clock 59 1779B–ATARM–03/02 Peripheral Clock Controller The clock of each peripheral integrated in the AT91M42800A can be individually enabled and disabled by writing into the Peripheral Clock Enable (PMC_PCER) and Peripheral Clock Disable (PMC_PCDR) registers. The status of the peripheral clock activity can be read in the Peripheral Clock Status Register (PMC_PCSR). When a peripheral clock is disabled, the clock is immediately stopped. When the clock is re-enabled, the peripheral resumes action where it left off. The peripheral clocks are automatically disabled after a reset. In order to stop a peripheral, it is recommended that the system software waits until the peripheral has executed its last programmed operation before disabling the clock. This is to avoid data corruption or erroneous behavior of the system. Note: The bits defined to control the Peripheral Clocks correspond to the bits controlling the Interrupt Sources in the Interrupt Controller. Figure 41. Peripheral Clock Control MCK Master Clock Peripheral Clock Y Peripheral Clock X PMC_PCER Set PMC_PCSR Clear Y X PMC_PCDR 60 AT91M42800A 1779B–ATARM–03/02 AT91M42800A PMC User Interface Base Address: 0xFFFF4000 (Code Label PMC_BASE) Table 10. PMC Registers Offset Register Name Register Mnemonic Access 0x00 System Clock Enable Register PMC_SCER Write-only – 0x04 System Clock Disable Register PMC_SCDR Write-only – 0x08 System Clock Status Register PMC_SCSR Read-only 0x00000001 0x0C Reserved – – – 0x10 Peripheral Clock Enable Register PMC_PCER Write-only – 0x14 Peripheral Clock Disable Register PMC_PCDR Write-only – 0x18 Peripheral Clock Status Register PMC_PCSR Read-only 0x00000000 0x1C Reserved – – 0x20 Clock Generator Mode Register PMC_CGMR Read/Write 0x24 Reserved – – – 0x28 Reserved – – – 0x2C Reserved – – – 0x30 Status Register PMC_SR Read-only 0x00000000 0x34 Interrupt Enable Register PMC_IER Write-only – 0x38 Interrupt Disable Register PMC_IDR Write-only – 0x3C Interrupt Mask Register PMC_IMR Read-only 0x00000000 Reset Value – 0x00000000 61 1779B–ATARM–03/02 PMC System Clock Enable Register Register Name: Access Type: Offset: PMC_SCER Write-only 0x00 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – CPU • CPU: System Clock Enable 0 = No effect. 1 = Enables the System Clock. PMC System Clock Disable Register Register Name: Access Type: Offset: PMC_SCDR Write-only 0x04 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – CPU • CPU: System Clock Disable 0 = No effect. 1 = Disables the System Clock. 62 AT91M42800A 1779B–ATARM–03/02 AT91M42800A PMC System Clock Status Register Register Name: Access Type: Offset: Reset Value: PMC_SCSR Read-only 0x08 0x01 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – CPU • CPU: System Clock Status 0 = System Clock is disabled. 1 = System Clock is enabled. PMC Peripheral Clock Enable Register Register Name: Access Type: Offset: PMC_PCER Write-only 0x10 31 30 29 28 27 26 25 24 – – – – –– – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – PIOB PIOA – TC5 TC4 TC3 TC2 7 6 5 4 3 2 1 0 TC1 TC0 SPIB SPIA US1 US0 – – • Peripheral Clock Enable 0 = No effect. 1 = Enables the peripheral clock. 63 1779B–ATARM–03/02 PMC Peripheral Clock Disable Register Register Name: Access Type: Offset: PMC_PCDR Write-only 0x14 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – PIOB PIOA – TC5 TC4 TC3 TC2 7 6 5 4 3 2 1 0 TC1 TC0 SPIB SPIA US1 US0 – – • Peripheral Clock Disable 0 = No effect. 1 = Disables the peripheral clock. PMC Peripheral Clock Status Register Register Name: Access Type: Offset: Reset Value: PMC_PCSR Read-only 0x1C 0x0 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – PIOB PIOA – TC5 TC4 TC3 TC2 7 6 5 4 3 2 1 0 TC1 TC0 SPIB SPIA US1 US0 – – • Peripheral Clock Status 0 = Peripheral clock is disabled. 1 = Peripheral clock is enabled. 64 AT91M42800A 1779B–ATARM–03/02 AT91M42800A PMC Clock Generator Mode Register Register Name: Access Type: Offset: Reset Value: PMC_CGMR Read/Write 0x20 0x0 31 30 29 28 27 26 18 25 24 17 16 PLLCOUNT 23 22 21 20 19 – – – – – 15 14 13 12 MUL 11 10 3 2 9 8 1 0 MUL 7 6 CSS MCKODS 5 4 MCKOSS PLLS PRES • PRES: Prescaler Selection PRES Prescaler Selected Code Label PMC_PRES 0 0 0 None. The Prescaler is bypassed. PMC_PRES_NONE 0 0 1 Divide by 2 PMC_PRES_DIV2 0 1 0 Divide by 4 PMC_PRES_DIV4 0 1 1 Divide by 8 PMC_PRES_DIV8 1 0 0 Divide by 16 PMC_PRES_DIV16 1 0 1 Divide by 32 PMC_PRES_DIV32 1 1 0 Divide by 64 PMC_PRES_DIV64 1 1 1 Reserved – • PLLS: PLL Selection 0 = The PLL A with 5 - 20 MHz output range is selected as PLL source. (Code Label PMC_PLL_A) • 1 = The PLL B with 20 - 80 MHz output range is selected as PLL source. (Code Label PMC_PLL_B) Note: This bit can be written only once after the reset. Any write of a different value than this one written the first time has no effect on the bit. • MCKOSS: Master Clock Output Source Selection MCKOSS Master Clock Output Source Select Code Label: PMC_MCKOSS 0 0 Slow Clock PMC_MCKOSS_SLCK 0 1 Master Clock PMC_MCKOSS_MCK 1 0 Master Clock inverted PMC_MCKOSS_MCKINV 1 1 Master Clock divided by 2 PMC_MCKOSS_MCK_DIV2 • MCKODS: Master Clock Output Disable (Code Label PMC_MCKO_DIS) 0 = The pin MCKO is driven with the clock selected by MCKOSS. 1 = The pin MCKO is tri-stated. 65 1779B–ATARM–03/02 • CSS: Clock Source Selection 0 = The clock source is the Slow Clock. 1 = The clock source is the output of the PLL. • MUL: Phase Lock Loop Factor 0 = The PLL is disabled, reducing at the minimum its power consumption. 1 up to 2047 = The PLL output is at frequency (MUL+1) x Slow Clock frequency when the LOCK bit is set. • PLLCOUNT: PLL Lock Counter Specifies the number of 32,768 Hz clock cycles for the PLL lock timer to count before the PLL is locked, after the PLL is started. PMC Status Register Register Name: Access Type: Offset: Reset Value: PMC_SR Read-only 0x30 0x0 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – LOCK • LOCK: PLL Lock Status 0 = The PLL output signal is not stabilized. 1 = The PLL output signal is stabilized. 66 AT91M42800A 1779B–ATARM–03/02 AT91M42800A PMC Interrupt Enable Register Register Name: Access Type: Offset: PMC_IER Write-only 0x34 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – LOCK • LOCK: PLL Lock Interrupt Enable 0 = No effect. 1 = Enables the PLL Lock Interrupt. PMC Interrupt Disable Register Register Name: Access Type: Offset: PMC_IDR Write-only 0x38 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – LOCK • LOCK: PLL Lock Interrupt Disable 0 = No effect. 1 = Disables the PLL Lock Interrupt. 67 1779B–ATARM–03/02 PMC Interrupt Mask Register Register Name: Access Type: Offset: Reset Value: PMC_IMR Read-only 0x3C 0x0 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – LOCK • LOCK: PLL Lock Interrupt Mask 0 = The PLL Lock Interrupt is disabled. 1 = The PLL Lock Interrupt is enabled. 68 AT91M42800A 1779B–ATARM–03/02 AT91M42800A ST: System Timer The System Timer module integrates three different free-running timers: • A Period Interval Timer setting the base time for an Operating System. • A Watchdog Timer having capabilities to reset the system in case of software deadlock. • A Real-time Timer counting elapsed seconds. These timers count using the Slow Clock. Typically, this clock has a frequency of 32.768 kHz. Figure 42. System Timer Module SLCK Slow Clock STIRQ System Timer Interrupt System Timer Module APB Interface NWDOVF PIT: Period Interval Timer The Period Interval Timer can be used to provide periodic interrupts for use by operating systems. It is built around a 16-bit down counter, which is preloaded by a value programmed in ST_PIMR (Period Interval Mode Register). When the PIT counter reaches 0, the bit PITS is set in ST_SR (Status Register), and an interrupt is generated, if it is enabled. The counter is then automatically reloaded and restarted. Writing to the ST_PIMR at any time immediately reloads and restarts the down counter with the new programmed value. Figure 43. Period Interval Timer PIV Period Interval Value SLCK Slow Clock Note: WDT: Watchdog Timer 16-bit Down Counter PITS Period Interval Timer Status If ST_PIMR is programmed with a period less or equal to the current MCK period, the update of the PITS status bit and its associated interrupt generation are unpredictable. The Watchdog Timer can be used to prevent system lock-up if the software becomes trapped in a deadlock. It is built around a 16-bit down counter loaded with the value defined in ST_WDMR (Watchdog Mode Register). It uses the Slow Clock divided by 128. This allows the maximum watchdog period to be 256 seconds (with a typical Slow Clock of 32.768 kHz). In normal operation, the user reloads the watchdog at regular intervals before the timer overflow occurs. This is done by writing to the ST_CR (Control Register) with the bit WDRST set. 69 1779B–ATARM–03/02 If an overflow does occur, the Watchdog Timer: • Sets the WDOVF in ST_SR (Status Register) from which an interrupt can be generated • Generates a pulse for 8 slow clock cycles on the external signal NWDOVF if the bit EXTEN in ST_WDMR is set • Generates an internal reset if the parameter RSTEN in ST_WDMR is set • Reloads and restarts the down counter Writing the ST_WDMR does not reload or restart the down counter. When the ST_CR is written the watchdog is immediately reloaded from ST_WDMR and restarted. The slow clock 128 divider is also immediately reset and restarted. When the ARM7TDMI enters debug mode, the output of the slow clock divider stops, preventing any internal or external reset during the debugging phase. Figure 44. Watchdog Timer WV Watchdog Value SLCK Slow Clock 1/128 16-bit Down Counter WDOVF Watchdog Overflow RSTEN - Reset Enable WDRST Watchdog Restart Internal Reset EXTEN- External Signal Enable NWDOVF RTT: Real-time Timer The Real-time Timer can be used to count elapsed seconds. It is built around a 20-bit counter fed by the Slow Clock divided by a programmable value. At reset this value is set to 0x8000, corresponding to feeding the real-time counter with a 1 Hz signal when the Slow Clock is 32.768 Hz. The 20-bit counter can count up to 1048576 seconds, corresponding to more than 12 days, then roll over to 0. The Real-time Timer value can be read at any time in the register ST_CRTR (Current Real-time Register). As this value can be updated asynchronously to the Master Clock, it is advisable to read this register twice at the same value to improve accuracy of the returned value. This current value of the counter is compared with the value written in the Alarm Register ST_RTAR (Real-time Alarm Register). If the counter value matches the alarm, the bit ALMS in ST_SR is set. The Alarm Register is set to its maximum value, corresponding to 0, after a reset. The bit RTTINC in ST_SR is set each time the 20-bit counter is incremented. This bit can be used to start an interrupt, or generate a one-second signal. Writing the ST_RTMR immediately reloads and restarts the clock divider with the new programmed value. This also resets the 20-bit counter. 70 AT91M42800A 1779B–ATARM–03/02 AT91M42800A Figure 45. Real-time Timer RTPRES Real Time Prescalar SLCK Slow Clock 16-bit Divider RTTINC Real-time Timer Increment 20-bit Counter = ALMV Alarm Value Note: ALMS Alarm Status If RTPRES is programmed with a period less or equal to the current MCK period, the update of the RTTINC and ALMS status bits and their associated interrupt generation are unpredictable. 71 1779B–ATARM–03/02 System Timer User Interface System Timer Base Address: 0xFFFF8000 Table 11. System Timer Registers Offset Register Name Register Mnemonic Access 0x00 Control Register ST_CR W 0x04 Period Interval Mode Register ST_PIMR R/W 0x00000000(1) 0x08 Watchdog Mode Register ST_WDMR R/W 0x00020000(1) 0x0C Real-time Mode Register ST_RTMR R/W 0x00008000 0x10 Status Register ST_SR R – 0x14 Interrupt Enable Register ST_IER W – 0x18 Interrupt Disable Register ST_IDR W – 0x1C Interrupt Mask Register ST_IMR R 0x0 0x20 Real-time Alarm Register ST_RTAR R/W 0x0 0x24 Current Real-time Register ST_CRTR R 0x0 Note: 72 Reset Value – 1. Corresponds to maximum value of the counter. AT91M42800A 1779B–ATARM–03/02 AT91M42800A System Timer Control Register Register Name: Access Type: Offset: ST_CR Write-only 0x00 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – WDRST • WDRST: Watchdog Timer Restart 0 = No effect. 1 = Reload the start-up value in the Watchdog Timer. 73 1779B–ATARM–03/02 System Timer Period Interval Mode Register Register Name: Access Type: Offset: Reset Value: ST_PIMR Read/Write 0x04 0x0 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 3 2 1 0 PIV 7 6 5 4 PIV • PIV: Period Interval Value Defines the value loaded in the 16-bit counter of the Period Interval Timer. The maximum period is obtained by programming PIV at 0x0 corresponding to 65536 Slow Clock cycles. System Timer Watchdog Mode Register Register Name: Access Type: Offset: Reset Value: ST_WDMR Read/Write 0x08 0x0002 0000 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – EXTEN RSTEN 15 14 13 12 11 10 9 8 3 2 1 0 WDV 7 6 5 4 WDV • WDV: Watchdog Counter Value Defines the value loaded in the 16-bit counter. The maximum period is obtained by programming WDV to 0x0 corresponding to 65536 • 128 Slow Clock cycles. • RSTEN: Reset Enable 0 = No reset is generated when a watchdog overflow occurs. 1 = An internal reset is generated when a watchdog overflow occurs. • EXTEN: External Signal Assertion Enable 0 = The NWDOVF is not tied low when a watchdog overflow occurs. 1 = The NWDOVF is tied low during 8 Slow Clock cycles when a watchdog overflow occurs. 74 AT91M42800A 1779B–ATARM–03/02 AT91M42800A System Timer Real-time Mode Register Register Name: Access Type: Offset: Reset Value: ST_RTMR Read/Write 0x0C 0x0000 8000 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 3 2 1 0 RTPRES 7 6 5 4 RTPRES • RTPRES: Real-time Timer Prescaler Value Defines the number of SLCK periods required to increment the Real-time Timer. The maximum period is obtained by programming RTPRES to 0x0 corresponding to 65536 Slow Clock cycles. System Timer Status Register Register Name: Access Type: Offset: ST_SR Read-only 0x10 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – ALMS RTTINC WDOVF PITS • PITS: Period Interval Timer Status 0 = The Period Interval Timer has not reached 0 since the last read of the Status Register. 1 = The Period Interval Timer has reached 0 since the last read of the Status Register. • WDOVF: Watchdog Overflow 0 = The Watchdog Timer has not reached 0 since the last read of the Status Register. 1 = The Watchdog Timer has reached 0 since the last read of the Status Register. • RTTINC: Real-time Timer Increment 0 = The Real-time Timer has not been incremented since the last read of the Status Register. 1 = The Real-time Timer has been incremented since the last read of the Status Register. • ALMS: Alarm Status 0 = No alarm compare has been detected since the last read of the Status Register. 1 = Alarm compare has been detected since the last read of the Status Register. 75 1779B–ATARM–03/02 System Timer Interrupt Enable Register Register Name: Access Type: Offset: ST_IER Write-only 0x14 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – ALMS RTTINC WDOVF PITS • PITS: Period Interval Timer Status Interrupt Enable 0 = No effect. 1 = Enables the Period Interval Timer Status Interrupt. • WDOVF: Watchdog Overflow Interrupt Enable 0 = No effect. 1 = Enables the Watchdog Overflow Interrupt. • RTTINC: Real-time Timer Increment Interrupt Enable 0 = No effect. 1 = Enables the Real-time Timer Increment Interrupt. • ALMS: Alarm Status Interrupt Enable 0 = No effect. 1 = Enables the Alarm Status Interrupt. 76 AT91M42800A 1779B–ATARM–03/02 AT91M42800A System Timer Interrupt Disable Register Register Name: Access Type: Offset: ST_IDR Write-only 0x18 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – ALMS RTTINC WDOVF PITS • PITS: Period Interval Timer Status Interrupt Disable 0 = No effect. 1 = Disables the Period Interval Timer Status Interrupt. • WDOVF: Watchdog Overflow Interrupt Disable 0 = No effect. 1 = Disables the Watchdog Overflow Interrupt. • RTTINC: Real-time Timer Increment Interrupt Disable 0 = No effect. 1 = Disables the Real-time Timer Increment Interrupt. • ALMS: Alarm Status Interrupt Disable 0 = No effect. 1 = Disables the Alarm Status Interrupt. 77 1779B–ATARM–03/02 System Timer Interrupt Mask Register Register Name: Access Type: Offset: Reset Value: ST_IMR Read-only 0x1C 0x0 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – ALMS RTTINC WDOVF PITS • PITS: Period Interval Timer Status Interrupt Mask 0 = Period Interval Timer Status Interrupt is disabled. 1 = Period Interval Timer Status Interrupt is enabled. • WDOVF: Watchdog Overflow Interrupt Mask 0 = Watchdog Overflow Interrupt is disabled. 1 = Watchdog Overflow Interrupt is enabled. • RTTINC: Real-time Timer Increment Interrupt Mask 0 = Real-time Timer Increment Interrupt is disabled. 1 = Real-time Timer Increment Interrupt is enabled. • ALMS: Alarm Status Interrupt Mask 0 = Alarm Status Interrupt is disabled. 1 = Alarm Status Interrupt is enabled. System Timer Real-time Alarm Register Register Name: Access Type: Offset: Reset Value: ST_RTAR Read/Write 0x20 0x0 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 11 10 9 8 3 2 1 0 ALMV 15 14 13 12 ALMV 7 6 5 4 ALMV • ALMV: Alarm Value Defines the Alarm value compared with the Real-time Timer. The maximum delay before ALMS status bit activation is obtained by programming ALMV to 0x0 corresponding to 1048576 seconds. 78 AT91M42800A 1779B–ATARM–03/02 AT91M42800A System Timer Current Real-time Register Register Name: Access Type: Offset: Reset Value: ST_CRTR Read-only 0x24 0x0 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 11 10 9 8 3 2 1 0 CRTV 15 14 13 12 CRTV 7 6 5 4 CRTV • CRTV: Current Real-time Value Returns the current value of the Real-time Timer. 79 1779B–ATARM–03/02 AIC: Advanced Interrupt Controller The AT91M42800A has an 8-level priority, individually maskable, vectored interrupt controller. This feature substantially reduces the software and real-time overhead in handling internal and external interrupts. The interrupt controller is connected to the NFIQ (fast interrupt request) and the NIRQ (standard interrupt request) inputs of the ARM7TDMI processor. The processor’s NFIQ line can only be asserted by the external fast interrupt request input: FIQ. The NIRQ line can be asserted by the interrupts generated by the on-chip peripherals and the external interrupt request lines: IRQ0 to IRQ3. The 8-level priority encoder allows the customer to define the priority between the different NIRQ interrupt sources. Internal sources are programmed to be level sensitive or edge triggered. External sources can be programmed to be positive or negative edge triggered or high- or lowlevel sensitive. The interrupt sources are listed in Table 12 and the AIC programmable registers in Table 13. Figure 46. Interrupt Controller Block Diagram FIQ Source Advanced Peripheral Bus (APB) Note: 80 NFIQ ARM7TDMI Core Control Logic Internal Interrupt Sources External Interrupt Sources NFIQ Manager Memorization Memorization Prioritization Controller NIRQ Manager NIRQ After a hardware reset, the external interrupt sources pins are controlled by the Controller. They must be configured to be controlled by the peripheral before being used. AT91M42800A 1779B–ATARM–03/02 AT91M42800A Table 12. AIC Interrupt Sources Interrupt Source Interrupt Name Interrupt Description 0 FIQ Fast Interrupt 1 SW Soft Interrupt (generated by the AIC) 2 US0 USART Channel 0 interrupt 3 US1 USART Channel 1 interrupt 4 SPIA SPI Channel A Interrupt 5 SPIB SPI Channel B Interrupt 6 TC0 Timer Channel 0 Interrupt 7 TC1 Timer Channel 1 Interrupt 8 TC2 Timer Channel 2 Interrupt 9 TC3 Timer Channel 3 Interrupt 10 TC4 Timer Channel 4 Interrupt 11 TC5 Timer Channel 5 Interrupt 12 ST System Timer Interrupt 13 PIOA Parallel I/O Controller A Interrupt 14 PIOB Parallel I/O Controller B Interrupt 15 PMC Power Management Controller Interrupt 16 – Reserved 17 – Reserved 18 – Reserved 19 – Reserved 20 – Reserved 21 – Reserved 22 – Reserved 23 – Reserved 24 – Reserved 25 – Reserved 26 – Reserved 27 – Reserved 28 IRQ3 External Interrupt 3 29 IRQ2 External Interrupt 2 30 IRQ1 External Interrupt 1 31 IRQ0 External Interrupt 0 81 1779B–ATARM–03/02 Hardware Interrupt Vectoring The hardware interrupt vectoring reduces the number of instructions to reach the interrupt handler to only one. By storing the following instruction at address 0x00000018, the processor loads the program counter with the interrupt handler address stored in the AIC_IVR register. Execution is then vectored to the interrupt handler corresponding to the current interrupt. ldr PC,[PC,# -&F20] The current interrupt is the interrupt with the highest priority when the Interrupt Vector Register (AIC_IVR) is read. The value read in the AIC_IVR corresponds to the address stored in the Source Vector Register (AIC_SVR) of the current interrupt. Each interrupt source has its corresponding AIC_SVR. In order to take advantage of the hardware interrupt vectoring it is necessary to store the address of each interrupt handler in the corresponding AIC_SVR, at system initialization. Priority Controller The NIRQ line is controlled by an 8-level priority encoder. Each source has a programmable priority level of 7 to 0. Level 7 is the highest priority and level 0 the lowest. When the AIC receives more than one unmasked interrupt at a time, the interrupt with the highest priority is serviced first. If both interrupts have equal priority, the interrupt with the lowest interrupt source number (see Table 12) is serviced first. The current priority level is defined as the priority level of the current interrupt at the time the register AIC_IVR is read (the interrupt which will be serviced). In the case when a higher priority unmasked interrupt occurs while an interrupt already exists, there are two possible outcomes depending on whether the AIC_IVR has been read. • If the NIRQ line has been asserted but the AIC_IVR has not been read, then the processor will read the new higher priority interrupt handler address in the AIC_IVR register and the current interrupt level is updated. • If the processor has already read the AIC_IVR then the NIRQ line is reasserted. When the processor has authorized nested interrupts to occur and reads the AIC_IVR again, it reads the new, higher priority interrupt handler address. At the same time the current priority value is pushed onto a first-in last-out stack and the current priority is updated to the higher priority. When the end of interrupt command register (AIC_EOICR) is written, the current interrupt level is updated with the last stored interrupt level from the stack (if any). Hence at the end of a higher priority interrupt, the AIC returns to the previous state corresponding to the preceding lower priority interrupt which had been interrupted. Interrupt Handling The interrupt handler must read the AIC_IVR as soon as possible. This de-asserts the NIRQ request to the processor and clears the interrupt in case it is programmed to be edge triggered. This permits the AIC to assert the NIRQ line again when a higher priority unmasked interrupt occurs. At the end of the interrupt service routine, the end of interrupt command register (AIC_EOICR) must be written. This allows pending interrupts to be serviced. Interrupt Masking 82 Each interrupt source, including FIQ, can be enabled or disabled using the command registers AIC_IECR and AIC_IDCR. The interrupt mask can be read in the Read-only register AIC_IMR. A disabled interrupt does not affect the servicing of other interrupts. AT91M42800A 1779B–ATARM–03/02 AT91M42800A Interrupt Clearing and Setting All interrupt sources which are programmed to be edge triggered (including FIQ) can be individually set or cleared by respectively writing to the registers AIC_ISCR and AIC_ICCR. This function of the interrupt controller is available for auto-test or software debug purposes. Fast Interrupt Request The external FIQ line is the only source which can raise a fast interrupt request to the processor. Therefore, it has no priority controller. The external FIQ line can be programmed to be positive or negative edge triggered or high- or low-level sensitive in the AIC_SMR0 register. The fast interrupt handler address can be stored in the AIC_SVR0 register. The value written into this register is available by reading the AIC_FVR register when an FIQ interrupt is raised. By storing the following instruction at address 0x0000001C, the processor will load the program counter with the interrupt handler address stored in the AIC_FVR register. ldr PC,[PC,# -&F20] Alternatively the interrupt handler can be stored starting from address 0x0000001C as described in the ARM7TDMI datasheet. Software Interrupt Interrupt source 1 of the advanced interrupt controller is a software interrupt. It must be programmed to be edge triggered in order to set or clear it by writing to the AIC_ISCR and AIC_ICCR. This is totally independent of the SWI instruction of the ARM7TDMI processor. Spurious Interrupt When the AIC asserts the NIRQ line, the ARM7TDMI enters IRQ mode and the interrupt handler reads the IVR. It may happen that the AIC de-asserts the NIRQ line after the core has taken into account the NIRQ assertion and before the read of the IVR. This behavior is called a Spurious Interrupt. The AIC is able to detect these Spurious Interrupts and returns the Spurious Vector when the IVR is read. The Spurious Vector can be programmed by the user when the vector table is initialized. A spurious interrupt may occur in the following cases: • With any sources programmed to be level sensitive, if the interrupt signal of the AIC input is de-asserted at the same time as it is taken into account by the ARM7TDMI. • If an interrupt is asserted at the same time as the software is disabling the corresponding source through AIC_IDCR (this can happen due to the pipelining of the ARM core). The same mechanism of spurious interrupt occurs if the ARM7TDMI reads the IVR (application software or ICE) when there is no interrupt pending. This mechanism is also valid for the FIQ interrupts. Once the AIC enters the spurious interrupt management, it asserts neither the NIRQ nor the NFIQ lines to the ARM7TDMI as long as the spurious interrupt is not acknowledged. Therefore, it is mandatory for the Spurious Interrupt Service Routine to acknowledge the “spurious” behavior by writing to the AIC_EOICR (End of Interrupt) before returning to the interrupted software. It also can perform other operation(s), e.g., trace possible undesirable behavior. 83 1779B–ATARM–03/02 Protect Mode The Protect Mode permits reading of the Interrupt Vector Register without performing the associated automatic operations. This is necessary when working with a debug system. When a Debug Monitor or an ICE reads the AIC User Interface, the IVR could be read. This would have the following consequences in normal mode. • If an enabled interrupt with a higher priority than the current one is pending, it is stacked. • If there is no enabled pending interrupt, the spurious vector is returned. In either case, an End of Interrupt command would be necessary to acknowledge and to restore the context of the AIC. This operation is generally not performed by the debug system. Hence the debug system would become strongly intrusive, and could cause the application to enter an undesired state. This is avoided by using Protect mode. The Protect mode is enabled by setting the AIC bit in the SF Protect Mode Register (see “SF: Special Function Registers” on page 116). When Protect mode is enabled, the AIC performs interrupt stacking only when a write access is performed on the AIC_IVR. Therefore, the Interrupt Service Routines must write (arbitrary data) to the AIC_IVR just after reading it. The new context of the AIC, including the value of the Interrupt Status Register (AIC_ISR), is updated with the current interrupt only when IVR is written. An AIC_IVR read on its own (e.g., by a debugger), modifies neither the AIC context nor the AIC_ISR. Extra AIC_IVR reads performed in between the read and the write can cause unpredictable results. Therefore, it is strongly recommended not to set a breakpoint between these two actions, nor to stop the software. The debug system must not write to the AIC_IVR as this would cause undesirable effects. The following table shows the main steps of an interrupt and the order in which they are performed according to the mode: Action Normal Mode Protect Mode Calculate active interrupt (higher than current or spurious) Read AIC_IVR Read AIC_IVR Determine and return the vector of the active interrupt Read AIC_IVR Read AIC_IVR Memorize interrupt Read AIC_IVR Read AIC_IVR Push on internal stack the current priority level Read AIC_IVR Write AIC_IVR Acknowledge the interrupt(1) Read AIC_IVR Write AIC_IVR Write AIC_IVR – (2) No effect Notes: 84 1. NIRQ de-assertion and automatic interrupt clearing if the source is programmed as level sensitive. 2. Software that has been written and debugged using Protect mode will run correctly in Normal mode without modification. However, in Normal mode, the AIC_IVR write has no effect and can be removed to optimize the code. AT91M42800A 1779B–ATARM–03/02 AT91M42800A AIC User Interface Base Address: 0xFFFFF000 (Code Label AIC_BASE) Table 13. AIC Memory Map Offset Register 0x000 0x004 – Access Reset State Source Mode Register 0 AIC_SMR0 Read/Write 0 Source Mode Register 1 AIC_SMR1 Read/Write 0 – Read/Write 0 – 0x07C Source Mode Register 31 AIC_SMR31 Read/Write 0 0x080 Source Vector Register 0 AIC_SVR0 Read/Write 0 0x084 Source Vector Register 1 AIC_SVR1 Read/Write 0 – Read/Write 0 AIC_SVR31 Read/Write 0 – Note: Name – 0x0FC Source Vector Register 31 0x100 IRQ Vector Register AIC_IVR Read-only – 0x104 FIQ Vector Register AIC_FVR Read-only – 0x108 Interrupt Status Register AIC_ISR Read-only – 0x10C Interrupt Pending Register AIC_IPR Read-only (see Note 1) 0x110 Interrupt Mask Register AIC_IMR Read-only 0 0x114 Core Interrupt Status Register AIC_CISR Read-only – 0x118 Reserved – – – 0x11C Reserved – – – 0x120 Interrupt Enable Command Register AIC_IECR Write-only – 0x124 Interrupt Disable Command Register AIC_IDCR Write-only – 0x128 Interrupt Clear Command Register AIC_ICCR Write-only – 0x12C Interrupt Set Command Register AIC_ISCR Write-only – 0x130 End of Interrupt Command Register AIC_EOICR Write-only – 0x134 Spurious Vector Register AIC_SPU Read/Write 0 1. The reset value of this register depends on the level of the External IRQ lines. All other sources are cleared at reset. 85 1779B–ATARM–03/02 AIC Source Mode Register Register Name: Access Type: Reset Value: AIC_SMR0..AIC_SMR31 Read/Write 0 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 4 3 2 1 0 – – – 5 SRCTYPE PRIOR • PRIOR: Priority Level (Code Label AIC_PRIOR) Program the priority level for all sources except source 0 (FIQ). The priority level can be between 0 (lowest) and 7 (highest). The priority level is not used for the FIQ, in the SMR0. • SRCTYPE: Interrupt Source Type (Code Label AIC_SRCTYPE) Program the input to be positive or negative edge-triggered or positive or negative level sensitive. The active level or edge is not programmable for the internal sources. SRCTYPE Code Label 0 0 Low-level Sensitive AIC_SRCTYPE_EXT_LOW_LEVEL 0 1 Negative Edge triggered AIC_SRCTYPE_EXT_NEGATIVE_EDGE 1 0 High-level Sensitive AIC_SRCTYPE_EXT_HIGH_LEVEL 1 1 Positive Edge triggered AIC_SRCTYPE_EXT_POSITIVE_EDGE Internal Sources Code Label SRCTYPE 86 External Sources X 0 Level Sensitive AIC_SRCTYPE_INT_LEVEL_SENSITIVE X 1 Edge triggered AIC_SRCTYPE_INT_EDGE_TRIGGERED AT91M42800A 1779B–ATARM–03/02 AT91M42800A AIC Source Vector Register Register Name: Access Type: Reset Value: 31 AIC_SVR0..AIC_SVR31 Read/Write 0 30 29 28 27 26 25 24 19 18 17 16 11 10 9 8 3 2 1 0 VECTOR 23 22 21 20 VECTOR 15 14 13 12 VECTOR 7 6 5 4 VECTOR • VECTOR: Interrupt Handler Address The user may store in these registers the addresses of the corresponding handler for each interrupt source. 87 1779B–ATARM–03/02 AIC Interrupt Vector Register Register Name: Access Type: Offset: 31 AIC_IVR Read-only 0x100 30 29 28 27 26 25 24 19 18 17 16 11 10 9 8 3 2 1 0 IRQV 23 22 21 20 IRQV 15 14 13 12 IRQV 7 6 5 4 IRQV • IRQV: Interrupt Vector Register The IRQ Vector Register contains the vector programmed by the user in the Source Vector Register corresponding to the current interrupt. The Source Vector Register (1 to 31) is indexed using the current interrupt number when the Interrupt Vector Register is read. When there is no current interrupt, the IRQ Vector Register reads the value stored in AIC_SPU. AIC FIQ Vector Register Register Name: Access Type: Offset: 31 AIC_FVR Read-only 0x104 30 29 28 27 26 25 24 19 18 17 16 11 10 9 8 3 2 1 0 FIQV 23 22 21 20 FIQV 15 14 13 12 FIQV 7 6 5 4 FIQV • FIQV: FIQ Vector Register The FIQ Vector Register contains the vector programmed by the user in the Source Vector Register 0 which corresponds to FIQ. 88 AT91M42800A 1779B–ATARM–03/02 AT91M42800A AIC Interrupt Status Register Register Name: Access Type: Offset: AIC_ISR Read-only 0x108 31 30 29 28 27 26 25 24 – – – –– – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – IRQID • IRQID: Current IRQ Identifier (Code Label AIC_IRQID) The Interrupt Status Register returns the current interrupt source number. 89 1779B–ATARM–03/02 AIC Interrupt Pending Register Register Name: Access Type: Offset: AIC_IPR Read-only 0x10C 31 30 29 28 27 26 25 24 IRQ0 IRQ1 IRQ2 IRQ3 – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 PMC PIOB PIOA ST TC5 TC4 TC3 TC2 7 6 5 4 3 2 1 0 TC1 TC0 SPIB SPIA US1 US0 SW FIQ • Interrupt Pending 0 = Corresponding interrupt is inactive. 1 = Corresponding interrupt is pending. AIC Interrupt Mask Register Register Name: Access Type: Offset: Reset Value: AIC_IMR Read-only 0x110 0x0 31 30 29 28 27 26 25 24 IRQ0 IRQ1 IRQ2 IRQ3 – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 PMC PIOB PIOA ST TC5 TC4 TC3 TC2 7 6 5 4 3 2 1 0 TC1 TC0 SPIB SPIA US1 US0 SW FIQ • Interrupt Mask 0 = Corresponding interrupt is disabled. 1 = Corresponding interrupt is enabled. 90 AT91M42800A 1779B–ATARM–03/02 AT91M42800A AIC Core Interrupt Status Register Register Name: Access Type: Offset: AIC_CISR Read-only 0x114 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – NIRQ NFIQ • NFIQ: NFIQ Status (Code Label AIC_NFIQ) 0 = NFIQ line inactive. 1 = NFIQ line active. • NIRQ: NIRQ Status (Code Label AIC_NIRQ) 0 = NIRQ line inactive. 1 = NIRQ line active. AIC Interrupt Enable Command Register Register Name: Access Type: Offset: AIC_IECR Write-only 0x120 31 30 29 28 27 26 25 24 IRQ0 IRQ1 IRQ2 IRQ3 – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 PMC PIOB PIOA ST TC5 TC4 TC3 TC2 7 6 5 4 3 2 1 0 TC1 TC0 SPIB SPIA US1 US0 SW FIQ • Interrupt Enable 0 = No effect. 1 = Enables corresponding interrupt. 91 1779B–ATARM–03/02 AIC Interrupt Disable Command Register Register Name: Access Type: Offset: AIC_IDCR Write-only 0x124 31 30 29 28 27 26 25 24 IRQ0 IRQ1 IRQ2 IRQ3 – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 PMC PIOB PIOA ST TC5 TC4 TC3 TC2 7 6 5 4 3 2 1 0 TC1 TC0 SPIB SPIA US1 US0 SW FIQ • Interrupt Disable 0 = No effect. 1 = Disables corresponding interrupt. 92 AT91M42800A 1779B–ATARM–03/02 AT91M42800A AIC Interrupt Clear Command Register Register Name: Access Type: Offset: AIC_ICCR Write-only 0x128 31 30 29 28 27 26 25 24 IRQ0 IRQ1 IRQ2 IRQ3 – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 PMC PIOB PIOA ST TC5 TC4 TC3 TC2 7 6 5 4 3 2 1 0 TC1 TC0 SPIB SPIA US1 US0 SW FIQ • Interrupt Clear 0 = No effect. 1 = Clears corresponding interrupt. AIC Interrupt Set Command Register Register Name: Access Type: Offset: AIC_ISCR Write-only 0x12C 31 30 29 28 27 26 25 24 IRQ0 IRQ1 IRQ2 IRQ3 – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 PMC PIOB PIOA ST TC5 TC4 TC3 TC2 7 6 5 4 3 2 1 0 TC1 TC0 SPIB SPIA US1 US0 SW FIQ • Interrupt Set 0 = No effect. 1 = Sets corresponding interrupt. 93 1779B–ATARM–03/02 AIC End of Interrupt Command Register Register Name: Access Type: Offset: AIC_EOICR Write-only 0x130 31 – 30 – 29 – 28 – 27 – 26 – 25 – 24 – 23 – 22 – 21 – 20 – 19 – 18 17 16 – – – 15 – 14 – 13 – 12 – 11 – 10 – 9 – 8 7 6 5 4 3 2 1 0 – – – – – – – – – The End of Interrupt Command Register is used by the interrupt routine to indicate that the interrupt treatment is complete. Any value can be written because it is only necessary to make a write to this register location to signal the end of interrupt treatment. AIC Spurious Vector Register Register Name: Access Type: Offset: Reset Value: 31 AIC_SPU Read/Write 0x134 0 30 29 28 27 26 25 24 19 18 17 16 11 10 9 8 3 2 1 0 SPUVEC 23 22 21 20 SPUVEC 15 14 13 12 SPUVEC 7 6 5 4 SPUVEC • SPUVEC: Spurious Interrupt Vector Handler Address The user may store the address of the spurious interrupt handler in this register. 94 AT91M42800A 1779B–ATARM–03/02 AT91M42800A Standard Interrupt Sequence It is assumed that: • • The Advanced Interrupt Controller has been programmed, AIC_SVR are loaded with corresponding interrupt service routine addresses and interrupts are enabled. The Instruction at address 0x18(IRQ exception vector address) is ldr pc, [pc, #-&F20] When NIRQ is asserted, if the bit I of CPSR is 0, the sequence is: 1. The CPSR is stored in SPSR_irq, the current value of the Program Counter is loaded in the IRQ link register (R14_irq) and the Program Counter (R15) is loaded with 0x18. In the following cycle during fetch at address 0x1C, the ARM core adjusts R14_irq, decrementing it by 4. 2. The ARM core enters IRQ mode, if it is not already. 3. When the instruction loaded at address 0x18 is executed, the Program Counter is loaded with the value read in AIC_IVR. Reading the AIC_IVR has the following effects: – Set the current interrupt to be the pending one with the highest priority. The current level is the priority level of the current interrupt. – De-assert the NIRQ line on the processor. (Even if vectoring is not used, AIC_IVR must be read in order to de-assert NIRQ) – Automatically clear the interrupt, if it has been programmed to be edge triggered. – Push the current level on to the stack. – Return the value written in the AIC_SVR corresponding to the current interrupt. 4. The previous step has effect to branch to the corresponding interrupt service routine. This should start by saving the Link Register(R14_irq) and the SPSR(SPSR_irq). Note that the Link Register must be decremented by 4 when it is saved, if it is to be restored directly into the Program Counter at the end of the interrupt. 5. Further interrupts can then be unmasked by clearing the I-bit in the CPSR, allowing re-assertion of the NIRQ to be taken into account by the core. This can occur if an interrupt with a higher priority than the current one occurs. 6. The Interrupt Handler can then proceed as required, saving the registers which will be used and restoring them at the end. During this phase, an interrupt of priority higher than the current level will restart the sequence from step 1. Note that if the interrupt is programmed to be level sensitive, the source of the interrupt must be cleared during this phase. 7. The I-bit in the CPSR must be set in order to mask interrupts before exiting, to ensure that the interrupt is completed in an orderly manner. 8. The End of Interrupt Command Register (AIC_EOICR) must be written in order to indicate to the AIC that the current interrupt is finished. This causes the current level to be popped from the stack, restoring the previous current level if one exists on the stack. If another interrupt is pending, with lower or equal priority than old current level but with higher priority than the new current level, the NIRQ line is re-asserted, but the interrupt sequence does not immediately start because the I-bit is set in the core. 95 1779B–ATARM–03/02 9. The SPSR (SPSR_irq) is restored. Finally, the saved value of the Link Register is restored directly into the PC. This has effect of returning from the interrupt to whatever was being executed before, and of loading the CPSR with the stored SPSR, masking or unmasking the interrupts depending on the state saved in the SPSR (the previous state of the ARM core). Note: 96 The I-bit in the SPSR is significant. If it is set, it indicates that the ARM core was just about to mask IRQ interrupts when the mask instruction was interrupted. Hence, when the SPSR is restored, the mask instruction is completed (IRQ is masked). AT91M42800A 1779B–ATARM–03/02 AT91M42800A Fast Interrupt Sequence It is assumed that: • • The Advanced Interrupt Controller has been programmed, AIC_SVR[0] is loaded with fast interrupt service routine address and the fast interrupt is enabled. The Instruction at address 0x1C(FIQ exception vector address) is: ldr pc, [pc, #-&F20] • Nested Fast Interrupts are not needed by the user. When NFIQ is asserted, if the F-bit of CPSR is 0, the sequence is: 1. The CPSR is stored in SPSR_fiq, the current value of the Program Counter is loaded in the FIQ link register (R14_fiq) and the Program Counter (R15) is loaded with 0x1C. In the following cycle, during fetch at address 0x20, the ARM core adjusts R14_fiq, decrementing it by 4. 2. The ARM core enters FIQ mode. 3. When the instruction loaded at address 0x1C is executed, the Program Counter is loaded with the value read in AIC_FVR. Reading the AIC_FVR has effect of automatically clearing the fast interrupt (source 0 connected to the FIQ line), if it has been programmed to be edge triggered. In this case only, it de-asserts the NFIQ line on the processor. 4. The previous step has effect to branch to the corresponding interrupt service routine. It is not necessary to save the Link Register(R14_fiq) and the SPSR(SPSR_fiq) if nested fast interrupts are not needed. 5. The Interrupt Handler can then proceed as required. It is not necessary to save registers R8 to R13 because FIQ mode has its own dedicated registers and the user R8 to R13 are banked. The other registers, R0 to R7, must be saved before being used, and restored at the end (before the next step). Note that if the fast interrupt is programmed to be level sensitive, the source of the interrupt must be cleared during this phase in order to de-assert the NFIQ line. 6. Finally, the Link Register (R14_fiq) is restored into the PC after decrementing it by 4 (with instruction sub pc, lr, #4 for example). This has effect of returning from the interrupt to whatever was being executed before, and of loading the CPSR with the SPSR, masking or unmasking the fast interrupt depending on the state saved in the SPSR. Note: The F-bit in the SPSR is significant. If it is set, it indicates that the ARM core was just about to mask FIQ interrupts when the mask instruction was interrupted. Hence when the SPSR is restored, the interrupted instruction is completed (FIQ is masked). 97 1779B–ATARM–03/02 PIO: Parallel I/O Controller The AT91M42800A has 54 programmable I/O lines. I/O lines are multiplexed with an external signal of a peripheral to optimize the use of available package pins (see Tables 14 and 15). These lines are controlled by two separate and identical PIO Controllers called PIOA and PIOB. Each PIO controller also provides an internal interrupt signal to the Advanced Interrupt Controller. Note: Multiplexed I/O Lines After a hardware reset, the PIO clock is disabled by default (see Power Management Controller on page 55). The user must configure the Power Management Controller before any access to the User Interface of the PIO. When a peripheral signal is not used in an application, the corresponding pin can be used as a parallel I/O. Each parallel I/O line is bi-directional, whether the peripheral defines the signal as input or output. Figure 47 shows the multiplexing of the peripheral signals with Parallel I/O signals. A pin is controlled by the registers PIO_PER (PIO Enable) and PIO_PDR (PIO Disable). The register PIO_PSR (PIO Status) indicates whether the pin is controlled by the corresponding peripheral or by the PIO Controller. When the PIO is selected, the peripheral input line is connected to zero. Output Selection The user can enable each individual I/O signal as an output with the registers PIO_OER (Output Enable) and PIO_ODR (Output Disable). The output status of the I/O signals can be read in the register PIO_OSR (Output Status). The direction defined has effect only if the pin is configured to be controlled by the PIO Controller. I/O Levels Each pin can be configured to be driven high or low. The level is defined in four different ways, according to the following conditions. • If a pin is controlled by the PIO Controller and is defined as an output (see Output Selection above), the level is programmed using the registers PIO_SODR (Set Output Data) and PIO_CODR (Clear Output Data). In this case, the programmed value can be read in PIO_ODSR (Output Data Status). • If a pin is controlled by the PIO Controller and is not defined as an output, the level is determined by the external circuit. • If a pin is not controlled by the PIO Controller, the state of the pin is defined by the peripheral (see peripheral datasheets). In all cases, the level on the pin can be read in the register PIO_PDSR (Pin Data Status). Filters Optional input glitch filtering is available on each pin and is controlled by the registers PIO_IFER (Input Filter Enable) and PIO_IFDR (Input Filter Disable). The input glitch filtering can be selected whether the pin is used for its peripheral function or as a parallel I/O line. The register PIO_IFSR (Input Filter Status) indicates whether or not the filter is activated for each pin. Interrupts Each parallel I/O can be programmed to generate an interrupt when a level change occurs. This is controlled by the PIO_IER (Interrupt Enable) and PIO_IDR (Interrupt Disable) registers which enable/disable the I/O interrupt by setting/clearin g the corresponding bit in the PIO_IMR. When a change in level occurs, the corresponding bit in the PIO_ISR (Interrupt Status) is set whether the pin is used as a PIO or a peripheral and whether it is defined as input or output. If the corresponding interrupt in PIO_IMR (Interrupt Mask) is enabled, the PIO interrupt is asserted. When PIO_ISR is read, the register is automatically cleared. 98 AT91M42800A 1779B–ATARM–03/02 AT91M42800A User Interface Each individual I/O is associated with a bit position in the Parallel I/O user interface registers. Each of these registers are 32 bits wide. If a parallel I/O line is not defined, writing to the corresponding bits has no effect. Undefined bits read zero. Multi-driver (Open Drain) Each I/O can be programmed for multi-driver option. This means that the I/O is configured as open drain (can only drive a low level) in order to support external drivers on the same pin. An external pull-up is necessary to guarantee a logic level of one when the pin is not being driven. Registers PIO_MDER (Multi-Driver Enable) and PIO_MDDR (Multi-Driver Disable) control this option. Multi-driver can be selected whether the I/O pin is controlled by the PIO Controller or the peripheral. PIO_MDSR (Multi-Driver Status) indicates which pins are configured to support external drivers. 99 1779B–ATARM–03/02 Figure 47. Parallel I/O Multiplexed with a Bi-directional Signal PIO_OSR 1 Pad Output Enable Peripheral Output Enable 0 0 1 PIO_PSR PIO_ODSR PIO_MDSR 1 Pad Output 0 Pad Pad Input Filter Peripheral Output 1 0 0 OFF Value(1) Peripheral Input 1 PIO_IFSR PIO_PSR PIO_PDSR Event Detection PIO_ISR PIO_IMR PIOIRQ Note: 100 1. See “PIO Connection Tables.” AT91M42800A 1779B–ATARM–03/02 AT91M42800A PIO Connection Tables Table 14. PIO Controller A Connection Table PIO Controller Peripheral OFF(1) Value Reset State Pin Number Input 0 PIO Input 77 External Interrupt 1 Input 0 PIO Input 78 IRQ2 External Interrupt 2 Input 0 PIO Input 79 PA3 IRQ3 External Interrupt 3 Input 0 PIO Input 80 4 PA4 FIQ Fast Interrupt Input 0 PIO Input 81 5 PA5 SCK0 USART0 Clock Signal Bi-directional 0 PIO Input 82 6 PA6 TXD0 USART0 Transmit Data Signal Output – PIO Input 83 7 PA7 RXD0 USART0 Receive Data Signal Input 0 PIO Input 86 8 PA8 SCK1 USART1 Clock Signal Bi-directional 0 PIO Input 87 9 PA9 TXD1/NTRI USART1 Transmit Data Signal Output – PIO Input 88 10 PA10 RXD1 USART1 Receive Data Signal Input 0 PIO Input 89 11 PA11 SPCKA SPIA Clock Signal Bi-directional 0 PIO Input 90 12 PA12 MISOA SPIA Master In Slave Out Bi-directional 0 PIO Input 91 13 PA13 MOSIA SPIA Master Out Slave In Bi-directional 0 PIO Input 92 14 PA14 NPCSA0/NSSA SPIA Peripheral Chip Select 0 Bi-directional 1 PIO Input 93 15 PA15 NPCSA1 SPIA Peripheral Chip Select 1 Output – PIO Input 94 16 PA16 NPCSA2 SPIA Peripheral Chip Select 2 Output – PIO Input 95 17 PA17 NPCSA3 SPIA Peripheral Chip Select 3 Output – PIO Input 98 18 PA18 SPCKB SPIB Clock Signal Bi-directional 0 PIO Input 99 19 PA19 MISOB SPIB Master In Slave Out Bi-directional 0 PIO Input 100 20 PA20 MOSIB SPIB Master Out Slave In Bi-directional 0 PIO Input 101 21 PA21 NPCSB0/NSSB SPIB Peripheral Chip Select 0 Bi-directional 1 PIO Input 102 22 PA22 NPCSB1 SPIB Peripheral Chip Select 1 Output – PIO Input 103 23 PA23 NPCSB2 SPIB Peripheral Chip Select 2 Output – PIO Input 104 24 PA24 NPCSB3 SPIB Peripheral Chip Select 3 Output – PIO Input 105 25 PA25 MCKO Master Clock Output Output – MCKO 106 26 PA26 – – – – PIO Input 111 27 PA27 BMS Boot Mode Select Input 0 PIO Input 123 28 PA28 – – Output – PIO Input 131 PIO Input 134 Bit Number Port Name Port Name Signal Description Signal Direction 0 PA0 IRQ0 External Interrupt 0 1 PA1 IRQ1 2 PA2 3 29 PA29 PME Protect Mode Enable Input 0 Note: 1. The OFF value is the default level seen on the peripheral input when the PIO line is enabled. 101 1779B–ATARM–03/02 Table 15. PIO Controller B Connection Table PIO Controller Peripheral OFF(1) Value Reset State Pin Number Output – NCS2 141 Chip Select 3 Output – NCS3 142 A20/CS7 Address 20/Chip Select 7 Output – A20 27 PB3 A21/CS6 Address 21/Chip Select 6 Output – A21 28 4 PB4 A22/CS5 Address 22/Chip Select 5 Output – A22 29 5 PB5 A23/CS4 Address 23/Chip Select 4 Output – A23 30 6 PB6 TCLK0 Timer0 Clock Signal Input 0 PIO Input 53 7 PB7 TIOA0 Timer0 Signal A Bi-directional 0 PIO Input 54 8 PB8 TIOB0 Timer0 Signal B Bi-directional 0 PIO Input 55 9 PB9 TCLK1 Timer1 Clock Signal Input 0 PIO Input 56 10 PB10 TIOA1 Timer1 Signal A Bi-directional 0 PIO Input 57 11 PB11 TIOB1 Timer1 Signal B Bi-directional 0 PIO Input 58 12 PB12 TCLK2 Timer2 Clock Signal Input 0 PIO Input 59 13 PB13 TIOA2 Timer2 Signal A Bi-directional 0 PIO Input 62 14 PB14 TIOB2 Timer2 Signal B Bi-directional 0 PIO Input 63 15 PB15 TCLK3 Timer3 Clock Signal Input 0 PIO Input 64 16 PB16 TIOA3 Timer3 Signal A Bi-directional 0 PIO Input 65 17 PB17 TIOB3 Timer3 Signal B Bi-directional 0 PIO Input 66 18 PB18 TCLK4 Timer4 Clock Signal Input 0 PIO Input 67 19 PB19 TIOA4 Timer4 Signal A Bi-directional 0 PIO Input 68 20 PB20 TIOB4 Timer4 Signal B Bi-directional 0 PIO Input 69 21 PB21 TCLK5 Timer5 Clock Signal Input 0 PIO Input 70 22 PB22 TIOA5 Timer5 Signal A Bi-directional 0 PIO Input 75 PIO Input 76 Bit Number Port Name Port Name 0 PB0 NCS2 Chip Select 2 1 PB1 NCS3 2 PB2 3 Signal Description Signal Direction 23 PB23 TIOB5 Timer5 Signal B Bi-directional 0 Note: 1. The OFF value is the default level seen on the peripheral input when the PIO line is enabled. 102 AT91M42800A 1779B–ATARM–03/02 AT91M42800A PIO User Interface PIO Controller A Base Address: 0xFFFEC000 (Code Label PIOA_BASE) PIO Controller B Base Address: 0xFFFF0000 (Code Label PIOB_BASE) Table 16. PIO Controller Memory Map Offset Notes: Register Name Access Reset State 0x00 PIO Enable Register PIO_PER Write-only – 0x04 PIO Disable Register PIO_PDR Write-only – 0x08 PIO Status Register PIO_PSR Read-only 0x3DFFFFFF (A) 0x00FFFFC0 (B) 0x0C Reserved – – – 0x10 Output Enable Register PIO_OER Write-only – 0x14 Output Disable Register PIO_ODR Write-only – 0x18 Output Status Register PIO_OSR Read-only 0 0x1C Reserved – – – 0x20 Input Filter Enable Register PIO_IFER Write-only – 0x24 Input Filter Disable Register PIO_IFDR Write-only – 0x28 Input Filter Status Register PIO_IFSR Read-only 0 0x2C Reserved – – – 0x30 Set Output Data Register PIO_SODR Write-only – 0x34 Clear Output Data Register PIO_CODR Write-only – 0x38 Output Data Status Register PIO_ODSR Read-only 0 0x3C Pin Data Status Register PIO_PDSR Read-only (see Note 1) 0x40 Interrupt Enable Register PIO_IER Write-only – 0x44 Interrupt Disable Register PIO_IDR Write-only – 0x48 Interrupt Mask Register PIO_IMR Read-only 0 0x4C Interrupt Status Register PIO_ISR Read-only (see Note 2) 0x50 Multi-driver Enable Register PIO_MDER Write-only – 0x54 Multi-driver Disable Register PIO_MDDR Write-only – 0x58 Multi-driver Status Register PIO_MDSR Read-only 0 0x5C Reserved – – – 1. The reset value of this register depends on the level of the external pins at reset. 2. This register is cleared at reset. However, the first read of the register can give a value not equal to zero if any changes have occurred on any pins between the reset and the read. 103 1779B–ATARM–03/02 PIO Enable Register Register Name: Access Type: Offset: PIO_PER Write-only 0x00 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 This register is used to enable individual pins to be controlled by the PIO Controller instead of the associated peripheral. When the PIO is enabled, the associated peripheral (if any) is held at logic zero. 0 = No effect. 1 = Enables the PIO to control the corresponding pin (disables peripheral control of the pin). PIO Disable Register Register Name: Access Type: Offset: PIO_PDR Write-only 0x04 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 This register is used to disable PIO control of individual pins. When the PIO control is disabled, the normal peripheral function is enabled on the corresponding pin. 0 = No effect. 1 = Disables PIO control (enables peripheral control) on the corresponding pin. 104 AT91M42800A 1779B–ATARM–03/02 AT91M42800A PIO Status Register Register Name: Access Type: Offset: Reset Value: PIO_PSR Read-only 0x08 0x3DFFFFFF (A) 0x00FFFFC0 (B) 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 This register indicates which pins are enabled for PIO control. This register is updated when PIO lines are enabled or disabled. 0 = PIO is inactive on the corresponding line (peripheral is active). 1 = PIO is active on the corresponding line (peripheral is inactive). 105 1779B–ATARM–03/02 PIO Output Enable Register Register Name: Access Type: Offset: PIO_OER Write-only 0x10 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 This register is used to enable PIO output drivers. If the pin is driven by a peripheral, this has no effect on the pin, but the information is stored. The register is programmed as follows: 0 = No effect. 1 = Enables the PIO output on the corresponding pin. PIO Output Disable Register Register Name: Access Type: Offset: PIO_ODR Write-only 0x14 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 This register is used to disable PIO output drivers. If the pin is driven by the peripheral, this has no effect on the pin, but the information is stored. The register is programmed as follows: 0 = No effect. 1 = Disables the PIO output on the corresponding pin. 106 AT91M42800A 1779B–ATARM–03/02 AT91M42800A PIO Output Status Register Register Name: Access Type: Offset: Reset Value: PIO_OSR Read-only 0x18 0 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 This register shows the PIO pin control (output enable) status which is programmed in PIO_OER and PIO ODR. The defined value is effective only if the pin is controlled by the PIO. The register reads as follows: 0 = The corresponding PIO is input on this line. 1 = The corresponding PIO is output on this line. 107 1779B–ATARM–03/02 PIO Input Filter Enable Register Register Name: Access Type: Offset: PIO_IFER Write-only 0x20 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 This register is used to enable input glitch filters. It affects the pin whether or not the PIO is enabled. The register is programmed as follows: 0 = No effect. 1 = Enables the glitch filter on the corresponding pin. PIO Input Filter Disable Register Register Name: Access Type: Offset: IO_IFDR Write-only 0x24 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 This register is used to disable input glitch filters. It affects the pin whether or not the PIO is enabled. The register is programmed as follows: 0 = No effect. 1 = Disables the glitch filter on the corresponding pin. 108 AT91M42800A 1779B–ATARM–03/02 AT91M42800A PIO Input Filter Status Register Register Name: Access Type: Offset: Reset Value: PIO_IFSR Read-only 0x28 0 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 This register indicates which pins have glitch filters selected. It is updated when PIO outputs are enabled or disabled by writing to PIO_IFER or PIO_IFDR. 0 = Filter is not selected on the corresponding input. 1 = Filter is selected on the corresponding input (peripheral and PIO). 109 1779B–ATARM–03/02 PIO Set Output Data Register Register Name: Access Type: Offset: PIO_SODR Write-only 0x30 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 This register is used to set PIO output data. It affects the pin only if the corresponding PIO output line is enabled and if the pin is controlled by the PIO. Otherwise, the information is stored. 0 = No effect. 1 = PIO output data on the corresponding pin is set. PIO Clear Output Data Register Register Name: Access Type: Offset: PIO_CODR Write-only 0x34 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 This register is used to clear PIO output data. It affects the pin only if the corresponding PIO output line is enabled and if the pin is controlled by the PIO. Otherwise, the information is stored. 0 = No effect. 1 = PIO output data on the corresponding pin is cleared. 110 AT91M42800A 1779B–ATARM–03/02 AT91M42800A PIO Output Data Status Register Register Name: Access Type: Offset: Reset Value: PIO_ODSR Read-only 0x38 0 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 This register shows the output data status which is programmed in PIO_SODR or PIO_CODR. The defined value is effective only if the pin is controlled by the PIO Controller and only if the pin is defined as an output. 0 = The output data for the corresponding line is programmed to 0. 1 = The output data for the corresponding line is programmed to 1. PIO Pin Data Status Register Register Name: Access Type: Offset: Reset Value: PIO_PDSR Read-only 0x3C Undefined 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 This register shows the state of the physical pin of the chip. The pin values are always valid, regardless of whether the pins are enabled as PIO, peripheral, input or output. The register reads as follows: 0 = The corresponding pin is at logic 0. 1 = The corresponding pin is at logic 1. 111 1779B–ATARM–03/02 PIO Interrupt Enable Register Register Name: Access Type: Offset: PIO_IER Write-only 0x40 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 This register is used to enable PIO interrupts on the corresponding pin. It has effect whether PIO is enabled or not. 0 = No effect. 1 = Enables an interrupt when a change of logic level is detected on the corresponding pin. PIO Interrupt Disable Register Register Name: Access Type: Offset: PIO_IDR Write-only 0x44 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 This register is used to disable PIO interrupts on the corresponding pin. It has effect whether the PIO is enabled or not. 0 = No effect. 1 = Disables the interrupt on the corresponding pin. Logic level changes are still detected. 112 AT91M42800A 1779B–ATARM–03/02 AT91M42800A PIO Interrupt Mask Register Register Name: Access Type: Offset: Reset Value: PIO_IMR Read-only 0x48 0 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 This register shows which pins have interrupts enabled. It is updated when interrupts are enabled or disabled by writing to PIO_IER or PIO_IDR. 0 = Interrupt is not enabled on the corresponding input pin. 1 = Interrupt is enabled on the corresponding input pin. PIO Interrupt Status Register Register Name: Access Type: Offset: PIO_ISR Read-only 0x4C 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 This register indicates for each pin when a logic value change has been detected (rising or falling edge). This is valid whether the PIO is selected for the pin or not and whether the pin is an input or an output. The register is reset to zero following a read, and at reset. 0 = No input change has been detected on the corresponding pin since the register was last read. 1 = At least one input change has been detected on the corresponding pin since the register was last read. 113 1779B–ATARM–03/02 PIO Multi-drive Enable Register Register Name: Access Type: Offset: PIO_MDER Write-only 0x50 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 This register is used to enable PIO output drivers to be configured as open drain to support external drivers on the same pin. 0 = No effect. 1 = Enables multi-drive option on the corresponding pin. PIO Multi-drive Disable Register Register Name: Access Type: Offset: PIO_MDDR Write-only 0x54 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 This register is used to disable the open drain configuration of the output buffer. 0 = No effect. 1 = Disables the multi-driver option on the corresponding pin. 114 AT91M42800A 1779B–ATARM–03/02 AT91M42800A PIO Multi-drive Status Register Register Name: Access Type: Offset: Reset Value: PIO_MDSR Read-only 0x58 0 31 30 29 28 27 26 25 24 P31 P30 P29 P28 P27 P26 P25 P24 23 22 21 20 19 18 17 16 P23 P22 P21 P20 P19 P18 P17 P16 15 14 13 12 11 10 9 8 P15 P14 P13 P12 P11 P10 P9 P8 7 6 5 4 3 2 1 0 P7 P6 P5 P4 P3 P2 P1 P0 This register indicates which pins are configured with open drain drivers. 0 = PIO is not configured as an open drain. 1 = PIO is configured as an open drain. 115 1779B–ATARM–03/02 SF: Special Function Registers Chip Identification The AT91M42800A provides registers that implement the following special functions: • Chip Identification • RESET Status • Protect Mode (see "Protect Mode" on page 84) The AT91M42800A chip identifier is 0x14280041. SF User Interface Chip ID Base Address: 0xFFF00000 (Code Label SF_BASE) Table 17. SF Memory Map Offset 116 Register Name Access Reset State 0x00 Chip ID Register SF_CIDR Read-only Hardwired 0x04 Chip ID Extension Register SF_EXID Read-only Hardwired 0x08 Reset Status Register SF_RSR Read-only See register description 0x0C Reserved – – – 0x10 Reserved – – – 0x14 Reserved – – – 0x18 Protect Mode Register SF_PMR Read/Write 0x0 AT91M42800A 1779B–ATARM–03/02 AT91M42800A Chip ID Register Register Name: Access Type: Offset: 31 SF_CIDR Read-only 0x00 30 29 EXT 28 27 26 NVPTYP 23 22 21 20 19 18 ARCH 15 14 25 24 17 16 9 8 1 0 ARCH VDSIZ 13 12 11 10 NVDSIZ NVPSIZ 7 6 5 0 1 0 4 3 2 VERSION • VERSION: Version of the Chip (Code Label SF_VERSION) This value is incremented by one with each new version of the chip (from zero to a maximum value of 31). • NVPSIZ: Nonvolatile Program Memory Size NVPSIZ Size Code Label: SF_NVPSIZ 0 0 0 0 None SF_NVPSIZ_NONE 0 0 1 1 32K Bytes SF_NVPSIZ_32K 0 1 0 1 64K Bytes SF_NVP_SIZ_64K 0 1 1 1 128K Bytes SF_NVP_SIZ_128K 1 0 0 1 256K Bytes SF_NVP_SIZ_256K Reserved – Others • NVDSIZ: Nonvolatile Data Memory Size NVDSIZ 0 0 0 0 Others Size Code Label: SF_NVDSIZ None SF_NVDSIZ_NONE Reserved – Size Code Label: SF_VDSIZ • VDSIZ: Volatile Data Memory Size VDSIZ 0 0 0 0 None SF_VDSIZ_NONE 0 0 0 1 1K Byte SF_VDSIZ_1K 0 0 1 0 2K Bytes SF_VDSIZ_2K 0 1 0 0 4K Bytes SF_VDSIZ_4K 1 0 0 0 8K Bytes SF_VDSIZ_8K Reserved – Others 117 1779B–ATARM–03/02 • ARCH: Chip Architecture Code of Architecture: Two BCD digits ARCH Selected ARCH Code Label: SF_ARCH 0110 0011 AT91x63yyy SF_ARCH_AT91x63 0100 0000 AT91x40yyy SF_ARCH_AT91x40 0101 0101 AT91x55yyy SF_ARCH_AT91x55 • NVPTYP: Nonvolatile Program Memory Type NVPTYP Type Code Label: SF_NVPTYP 0 0 1 “M” Series or “F” Series SF_NVPTYP_M 1 0 0 “R” Series SF_NVPTYP_R • EXT: Extension Flag (Code Label SF_EXT) 0 = Chip ID has a single register definition without extensions. 1 = An extended Chip ID exists (to be defined in the future). Chip ID Extension Register Register Name: Access Type: Offset: SF_EXID Read-only 0x04 This register is reserved for future use. It will be defined when needed. 118 AT91M42800A 1779B–ATARM–03/02 AT91M42800A Reset Status Register Register Name: Access Type: Offset: SF_RSR Read-only 0x08 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 RESET • RESET: Reset Status Information This field indicates whether the reset was demanded by the external system (via NRST) or by the Watchdog internal reset request. Reset Cause of Reset Code Label 0x6C External Pin SF_EXT_RESET 0x53 Internal Watchdog SF_WD_RESET SF Protect Mode Register Register Name: Offset: Reset Value: 31 SF_PMR 0x18 0x00000000 30 29 28 27 26 25 24 19 18 17 16 PMRKEY 23 22 21 20 PMRKEY 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – AIC – – – – – • AIC: AIC Protect Mode Enable (Code Label SF_AIC) 0 = The Advanced Interrupt Controller runs in Normal Mode. 1 = The Advanced Interrupt Controller runs in Protect Mode. See "Protect Mode" on page 84. • PMRKEY: Protect Mode Register Key Used only when writing SF_PMR. PMRKEY reads 0. 0x27A8: Write access in SF_PMR is allowed. Other value: Write access in SF_PMR is prohibited. 119 1779B–ATARM–03/02 USART: Universal Synchronous/ Asynchronous Receiver/Transmitter The AT91M42800A provides two identical, full-duplex, universal synchronous/asynchronous receiver/transmitters that interface to the APB and are connected to the Peripheral Data Controller. The main features are: • Programmable Baud Rate Generator with External or Internal Clock, as well as Slow Clock • Parity, Framing and Overrun Error Detection • Line Break Generation and Detection • Automatic Echo, Local Loopback and Remote Loopback channel modes • Multi-drop Mode: Address Detection and Generation • Interrupt Generation • Two Dedicated Peripheral Data Controller channels • 5-, 6-, 7-, 8- and 9-bit character length Figure 48. USART Block Diagram ASB Peripheral Data Controller AMBA Receiver Channel Transmitter Channel USART Channel APB PIO: Parallel I/O Controller Control Logic USxIRQ MCKI MCKI/8 SLCK SCK 120 Receiver RXD Transmitter TXD Interrupt Control Baud Rate Generator Baud Rate Clock SCK AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A Pin Description Each USART channel has the following external signals: Name Description SCK USART Serial clock can be configured as input or output: SCK is configured as input if an External clock is selected (USCLKS = 3) SCK is driven as output if the External Clock is disabled (USCLKS ≠ 3) and Clock output is enabled (CLKO = 1) TXD Transmit Serial Data is an output RXD Notes: Receive Serial Data is an input 1. After a hardware reset, the USART clock is disabled by default (see “PMC: Power Management Controller” on page 55). The user must configure the Power Management Controller before any access to the User Interface of the USART. 2. After a hardware reset, the USART pins are deselected by default (see “PIO: Parallel I/O Controller” on page 98). The user must configure the PIO Controller before enabling the transmitter or receiver. If the user selects one of the internal clocks, SCK can be configured as a PIO. 121 1779B–ATARM–22-Mar-02 Baud Rate Generator The Baud Rate Generator provides the bit period clock (the Baud Rate clock) to both the Receiver and the Transmitter. The Baud Rate Generator can select between external and internal clock sources. The external clock source is SCK. The internal clock sources can be either the master clock MCK or the master clock divided by 8 (MCK/8). Note: In all cases, if an external clock is used, the duration of each of its levels must be longer than the system clock (MCK) period. The external clock frequency must be at least 2.5 times lower than the system clock. When the USART is programmed to operate in Asynchronous Mode (SYNC = 0 in the Mode Register US_MR), the selected clock is divided by 16 times the value (CD) written in US_BRGR (Baud Rate Generator Register). If US_BRGR is set to 0, the Baud Rate Clock is disabled. Baud Rate Selected Clock 16 x CD = When the USART is programmed to operate in Synchronous Mode (SYNC = 1) and the selected clock is internal (USCLKS ≠ 3 in the Mode Register US_MR), the Baud Rate Clock is the internal selected clock divided by the value written in US_BRGR. If US_BRGR is set to 0, the Baud Rate Clock is disabled. Baud Rate = Selected Clock CD In Synchronous Mode with external clock selected (USCLKS = 3), the clock is provided directly by the signal on the SCK pin. No division is active. The value written in US_BRGR has no effect. Figure 49. Baud Rate Generator USCLKS MCK MCK/8 SLCK SCK CD CD 0 CLK 16-bit Counter OUT SYNC >1 1 1 0 0 0 Divide by 16 0 Baud Rate Clock 1 1 SYNC 122 AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A Receiver Asynchronous Receiver The USART is configured for asynchronous operation when SYNC = 0 (bit 7 of US_MR). In asynchronous mode, the USART detects the start of a received character by sampling the RXD signal until it detects a valid start bit. A low level (space) on RXD is interpreted as a valid start bit if it is detected for more than 7 cycles of the sampling clock, which is 16 times the baud rate. Hence a space which is longer than 7/16 of the bit period is detected as a valid start bit. A space which is 7/16 of a bit period or shorter is ignored and the receiver continues to wait for a valid start bit. When a valid start bit has been detected, the receiver samples the RXD at the theoretical mid-point of each bit. It is assumed that each bit lasts 16 cycles of the sampling clock (one bit period) so the sampling point is 8 cycles (0.5 bit periods) after the start of the bit. The first sampling point is therefore 24 cycles (1.5 bit periods) after the falling edge of the start bit was detected. Each subsequent bit is sampled 16 cycles (1 bit period) after the previous one. Figure 50. Asynchronous Mode: Start Bit Detection 16 x Baud Rate Clock RXD Sampling D0 True Start Detection Figure 51. Asynchronous Mode: Character Reception Example: 8-bit, parity enabled 1 stop 0.5-bit period 1-bit period RXD Sampling D0 D1 True Start Detection D2 D3 D4 D5 D6 Stop Bit D7 Parity Bit 123 1779B–ATARM–22-Mar-02 Synchronous Receiver When configured for synchronous operation (SYNC = 1), the receiver samples the RXD signal on each rising edge of the Baud Rate clock. If a low level is detected, it is considered as a start. Data bits, parity bit and stop bit are sampled and the receiver waits for the next start bit. See example in Figure 52. Figure 52. Synchronous Mode: Character Reception Example: 8-bit, parity enabled 1 stop SCK RXD Sampling D0 D1 True Start Detection D2 D3 D4 D5 D6 Stop Bit D7 Parity Bit Receiver Ready When a complete character is received, it is transferred to the US_RHR and the RXRDY status bit in US_CSR is set. If US_RHR has not been read since the last transfer, the OVRE status bit in US_CSR is set. Parity Error Each time a character is received, the receiver calculates the parity of the received data bits, in accordance with the field PAR in US_MR. It then compares the result with the received parity bit. If different, the parity error bit PARE in US_CSR is set. Framing Error If a character is received with a stop bit at low level and with at least one data bit at high level, a framing error is generated. This sets FRAME in US_CSR. Time-out This function allows an idle condition on the RXD line to be detected. The maximum delay for which the USART should wait for a new character to arrive while the RXD line is inactive (high level) is programmed in US_RTOR (Receiver Tim-out). When this register is set to 0, no time-out is detected. Otherwise, the receiver waits for a first character and then initializes a counter which is decremented at each bit period and reloaded at each byte reception. When the counter reaches 0, the TIMEOUT bit in US_CSR is set. The user can restart the wait for a first character with the STTTO (Start Time-out) bit in US_CR. Calculation of time-out duration: Duration = Value x 4 x Bit Period 124 AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A Transmitter The transmitter has the same behavior in both synchronous and asynchronous operating modes. Start bit, data bits, parity bit and stop bits are serially shifted, lowest significant bit first, on the falling edge of the serial clock. See example in Figure 53. The number of data bits is selected in the CHRL field in US_MR. The parity bit is set according to the PAR field in US_MR. The number of stop bits is selected in the NBSTOP field in US_MR. When a character is written to US_THR (Transmit Holding), it is transferred to the Shift Register as soon as it is empty. When the transfer occurs, the TXRDY bit in US_CSR is set until a new character is written to US_THR. If Transmit Shift Register and US_THR are both empty, the TXEMPTY bit in US_CSR is set. Time-guard The Time-guard function allows the transmitter to insert an idle state on the TXD line between two characters. The duration of the idle state is programmed in US_TTGR (Transmitter Time-guard). When this register is set to zero, no time-guard is generated. Otherwise, the transmitter holds a high level on TXD after each transmitted byte during the number of bit periods programmed in US_TTGR. Idle state duration = Time-guard x Bit between two characters Value Period Figure 53. Synchronous and Asynchronous Modes: Character Transmission Example: 8-bit, parity enabled 1 stop Baud Rate Clock TXD Start Bit Multi-drop Mode D0 D1 D2 D3 D4 D5 D6 D7 Parity Bit Stop Bit When the field PAR in US_MR equals 11X (binary value), the USART is configured to run in Multi-drop mode. In this case, the parity error bit PARE in US_CSR is set when data is detected with a parity bit set to identify an address byte. PARE is cleared with the Reset Status Bits Command (RSTSTA) in US_CR. If the parity bit is detected low, identifying a data byte, PARE is not set. The transmitter sends an address byte (parity bit set) when a Send Address Command (SENDA) is written to US_CR. In this case, the next byte written to US_THR will be transmitted as an address. After this any byte transmitted will have the parity bit cleared. Break A break condition is a low signal level that has a duration of at least one character (including start/stop bits and parity). Transmit Break The transmitter generates a break condition on the TXD line when STTBRK is set in US_CR (Control Register). In this case, the character present in the Transmit Shift Register is completed before the line is held low. To cancel a break condition on the TXD line, the STPBRK command in US_CR must be set. The USART completes a minimum break duration of one character length. The TXD line then returns to high level (idle state) for at least 12 bit periods, or the value of the 125 1779B–ATARM–22-Mar-02 Time-guard register if it is greater than 12, to ensure that the end of break is correctly detected. Then the transmitter resumes normal operation. The BREAK is managed like a character: • The STTBRK and the STPBRK commands are performed only if the transmitter is ready (bit TXRDY = 1 in US_CSR) • The STTBRK command blocks the transmitter holding register (bit TXRDY is cleared in US_CSR) until the break has started • A break is started when the Shift Register is empty (any previous character is fully transmitted). US_CSR.TXEMPTY is cleared. The break blocks the transmitter shift register until it is completed (high level for at least 12 bit periods after the STPBRK command is requested) In order to avoid unpredictable states: • STTBRK and STPBRK commands must not be requested at the same time • Once an STTBRK command is requested, further STTBRK commands are ignored until the BREAK is ended (high level for at least 12 bit periods) • All STPBRK commands requested without a previous STTBRK command are ignored • A byte written into the Transmit Holding Register while a break is pending but not started (bit TXRDY = 0 in US_CSR) is ignored • It is not permitted to write new data in the Transmit Holding Register while a break is in progress (STPBRK has not been requested), even though TXRDY = 1 in US_CSR. • A new STTBRK command must not be issued until an existing break has ended (TXEMPTY=1 in US_CSR). The standard break transmission sequence is: 1. Wait for the transmitter ready (US_CSR.TXRDY = 1) 2. Send the STTBRK command (write 0x0200 to US_CR) 3. Wait for the transmitter ready (bit TXRDY = 1 in US_CSR) 4. Send the STPBRK command (write 0x0400 to US_CR) The next byte can then be sent: 5. Wait for the transmitter ready (bit TXRDY = 1 in US_CSR) 6. Send the next byte (write byte to US_THR) Each of these steps can be scheduled by using the interrupt if the bit TXRDY in US_IMR is set. For character transmission, the USART channel must be enabled before sending a break. 126 AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A Receive Break The receiver detects a break condition when all data, parity and stop bits are low. When the low stop bit is detected, the receiver asserts the RXBRK bit in US_CSR. An end of receive break is detected by a high level for at least 2/16 of a bit period in asynchronous operating mode or at least one sample in synchronous operating mode. RXBRK is also asserted when an end of break is detected. Both the beginning and the end of a break can be detected by interrupt if the bit US_IMR.RXBRK is set. Peripheral Data Controller Each USART channel is closely connected to a corresponding Peripheral Data Controller channel. One is dedicated to the receiver. The other is dedicated to the transmitter. The PDC is disabled if 9-bit character length is selected (MODE9 = 1) in US_MR. The PDC channel is programmed using US_TPR (Transmit Pointer) and US_TCR (Transmit Counter) for the transmitter and US_RPR (Receive Pointer) and US_RCR (Receive Counter) for the receiver. The status of the PDC is given in US_CSR by the ENDTX bit for the transmitter and by the ENDRX bit for the receiver. The pointer registers (US_TPR and US_RPR) are used to store the address of the transmit or receive buffers. The counter registers (US_TCR and US_RCR) are used to store the size of these buffers. The receiver data transfer is triggered by the RXRDY bit and the transmitter data transfer is triggered by TXRDY. When a transfer is performed, the counter is decremented and the pointer is incremented. When the counter reaches 0, the status bit is set (ENDRX for the receiver, ENDTX for the transmitter in US_CSR) and can be programmed to generate an interrupt. Transfers are then disabled until a new non-zero counter value is programmed. Interrupt Generation Each status bit in US_CSR has a corresponding bit in US_IER (Interrupt Enable) and US_IDR (Interrupt Disable) which controls the generation of interrupts by asserting the USART interrupt line connected to the Advanced Interrupt Controller. US_IMR (Interrupt Mask Register) indicates the status of the corresponding bits. When a bit is set in US_CSR and the same bit is set in US_IMR, the interrupt line is asserted. Channel Modes The USART can be programmed to operate in three different test modes, using the field CHMODE in US_MR. Automatic echo mode allows bit by bit re-transmission. When a bit is received on the RXD line, it is sent to the TXD line. Programming the transmitter has no effect. Local loopback mode allows the transmitted characters to be received. TXD and RXD pins are not used and the output of the transmitter is internally connected to the input of the receiver. The RXD pin level has no effect and the TXD pin is held high, as in idle state. Remote loopback mode directly connects the RXD pin to the TXD pin. The Transmitter and the Receiver are disabled and have no effect. This mode allows bit-by-bit retransmission. 127 1779B–ATARM–22-Mar-02 Figure 54. Channel Modes Automatic Echo RXD Receiver Transmitter Disabled TXD Local Loopback Disabled Receiver RXD VDD Disabled Transmitter Remote Loopback Receiver Transmitter 128 TXD VDD Disabled Disabled RXD TXD AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A USART User Interface Base Address USART0: Base Address USART1: 0xFFFC0000 (Code Label USART0_BASE) 0xFFFC4000 (Code Label USART1_BASE) Table 1. USART Memory Map Offset Register Name Access Reset State 0x00 Control Register US_CR Write-only – 0x04 Mode Register US_MR Read/Write 0 0x08 Interrupt Enable Register US_IER Write-only – 0x0C Interrupt Disable Register US_IDR Write-only – 0x10 Interrupt Mask Register US_IMR Read-only 0 0x14 Channel Status Register US_CSR Read-only 0x18 0x18 Receiver Holding Register US_RHR Read-only 0 0x1C Transmitter Holding Register US_THR Write-only – 0x20 Baud Rate Generator Register US_BRGR Read/Write 0 0x24 Receiver Time-out Register US_RTOR Read/Write 0 0x28 Transmitter Time-guard Register US_TTGR Read/Write 0 0x2C Reserved – – – 0x30 Receive Pointer Register US_RPR Read/Write 0 0x34 Receive Counter Register US_RCR Read/Write 0 0x38 Transmit Pointer Register US_TPR Read/Write 0 0x3C Transmit Counter Register US_TCR Read/Write 0 129 1779B–ATARM–22-Mar-02 USART Control Register Name: Access Type: Offset: US_CR Write-only 0x00 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – SENDA STTTO STPBRK STTBRK RSTSTA 7 6 5 4 3 2 1 0 TXDIS TXEN RXDIS RXEN RSTTX RSTRX – – • RSTRX: Reset Receiver (Code Label US_RSTRX) 0 = No effect. 1 = The receiver logic is reset. • RSTTX: Reset Transmitter (Code Label US_RSTTX) 0 = No effect. 1 = The transmitter logic is reset. • RXEN: Receiver Enable (Code Label US_RXEN) 0 = No effect. 1 = The receiver is enabled if RXDIS is 0. • RXDIS: Receiver Disable (Code Label US_RXDIS) 0 = No effect. 1 = The receiver is disabled. • TXEN: Transmitter Enable (Code Label US_TXEN) 0 = No effect. 1 = The transmitter is enabled if TXDIS is 0. • TXDIS: Transmitter Disable (Code Label US_TXDIS) 0 = No effect. 1 = The transmitter is disabled. • RSTSTA: Reset Status Bits (Code Label US_RSTSTA) 0 = No effect. 1 = Resets the status bits PARE, FRAME, OVRE and RXBRK in the US_CSR. • STTBRK: Start Break (Code Label US_STTBRK) 0 = No effect. 1 = If break is not being transmitted, start transmission of a break after the characters present in US_THR and the Transmit Shift Register have been transmitted. • STPBRK: Stop Break (Code Label US_STPBRK) 0 = No effect. 1 = If a break is being transmitted, stop transmission of the break after a minimum of one character length and transmit a high level during 12 bit periods. • STTTO: Start Time-out (Code Label US_STTTO) 0 = No effect. 1 = Start waiting for a character before clocking the time-out counter. • SENDA: Send Address (Code Label US_SENDA) 0 = No effect. 1 = In Multi-drop Mode only, the next character written to the US_THR is sent with the address bit set. 130 AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A USART Mode Register Name: Access Type: Offset: Reset Value: US_MR Read/Write 0x04 0x0 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – CLKO MODE9 – 14 13 12 11 10 9 15 CHMODE 7 NBSTOP 6 5 CHRL PAR 4 USCLKS 8 SYNC 3 2 1 0 – – – – • USCLKS: Clock Selection (Baud Rate Generator Input Clock) USCLKS Selected Clock Code Label: US_CLKS 0 0 MCK US_CLKS_MCK 0 1 MCK/8 US_CLKS_MCK8 1 0 Slow Clock US_CLKS_SLCK 1 1 External (SCK) US_CLKS_SCK Character Length Code Label: US_CHRL • CHRL: Character Length CHRL 0 0 Five bits US_CHRL_5 0 1 Six bits US_CHRL_6 1 0 Seven bits US_CHRL_7 1 1 Eight bits US_CHRL_8 Start, stop and parity bits are added to the character length. • SYNC: Synchronous Mode Select (Code Label US_SYNC) 0 = USART operates in Asynchronous Mode. 1 = USART operates in Synchronous Mode. • PAR: Parity Type PAR Parity Type Code Label: US_PAR 0 0 0 Even Parity US_PAR_EVEN 0 0 1 Odd Parity US_PAR_ODD 0 1 0 Parity forced to 0 (Space) US_PAR_SPACE 0 1 1 Parity forced to 1 (Mark) US_PAR_MARK 1 0 x No parity US_PAR_NO 1 1 x Multi-drop mode US_PAR_MULTIDROP 131 1779B–ATARM–22-Mar-02 • NBSTOP: Number of Stop Bits The interpretation of the number of stop bits depends on SYNC. Table 2. NBSTOP Asynchronous (SYNC = 0) Synchronous (SYNC = 1) Code Label: US_NBSTOP 0 0 1 stop bit 1 stop bit US_NBSTOP_1 0 1 1.5 stop bits Reserved US_NBSTOP_1_5 1 0 2 stop bits 2 stop bits US_NBSTOP_2 1 1 Reserved Reserved – Note: 1.5 or 2 stop bits are reserved for the TX function. The RX function uses only the 1 stop bit (there is no check on the 2 stop bit timeslot if NBSTO P= 10). • CHMODE: Channel Mode CHMODE Mode Description Code Label: US_CHMODE 0 0 Normal Mode The USART Channel operates as an Rx/Tx USART. US_CHMODE_NORMAL 0 1 Automatic Echo Receiver Data Input is connected to TXD pin. US_CHMODE_AUTOMATIC_ECHO 1 0 Local Loopback Transmitter Output Signal is connected to Receiver Input Signal. US_CHMODE_LOCAL_LOOPBACK 1 1 Remote Loopback RXD pin is internally connected to TXD pin. US_CHMODE_REMOTE_LOOPBACK • MODE9: 9-Bit Character Length (Code Label US_MODE9) 0 = CHRL defines character length. 1 = 9-Bit character length. • CKLO: Clock Output Select (Code Label US_CLKO) 0 = The USART does not drive the SCK pin. 1 = The USART drives the SCK pin. 132 AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A USART Interrupt Enable Register Name: Access Type: Offset: US_IER Write-only 0x08 31 30 29 28 27 26 25 24 COMMRX COMMTX – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – TXEMPTY TIMEOUT 7 6 5 4 3 2 1 0 PARE FRAME OVRE ENDTX ENDRX RXBRK TXRDY RXRDY • RXRDY: Enable RXRDY Interrupt (Code Label US_RXRDY) 0 = No effect. 1 = Enables RXRDY Interrupt. • TXRDY: Enable TXRDY Interrupt (Code Label US_TXRDY) 0 = No effect. 1 = Enables TXRDY Interrupt. • RXBRK: Enable Receiver Break Interrupt (Code Label US_RXBRK) 0 = No effect. 1 = Enables Receiver Break Interrupt. • ENDRX: Enable End of Receive Transfer Interrupt (Code Label US_ENDRX) 0 = No effect. 1 = Enables End of Receive Transfer Interrupt. • ENDTX: Enable End of Transmit Transfer Interrupt (Code Label US_ENDTX) 0 = No effect. 1 = Enables End of Transmit Transfer Interrupt. • OVRE: Enable Overrun Error Interrupt (Code Label US_OVRE) 0 = No effect. 1 = Enables Overrun Error Interrupt. • FRAME: Enable Framing Error Interrupt (Code Label US_FRAME) 0 = No effect. 1 = Enables Framing Error Interrupt. • PARE: Enable Parity Error Interrupt (Code Label US_PARE) 0 = No effect. 1 = Enables Parity Error Interrupt. • TIMEOUT: Enable Time-out Interrupt (Code Label US_TIMEOUT) 0 = No effect. 1 = Enables Reception Time-out Interrupt. • TXEMPTY: Enable TXEMPTY Interrupt (Code Label US_TXEMPTY) 0 = No effect. 1 = Enables TXEMPTY Interrupt. • COMMTX: Enable ARM7TDMI ICE Debug Communication Channel Transmit Interrupt This bit is implemented for USART0 only. 0 = No effect. 1 = Enables COMMTX Interrupt • COMMRX: Enable ARM7TDMI ICE Debug Communication Channel Receive Interrupt This bit is implemented for USART0 only. 0 = No effect. 1 = Enables COMMRX Interrupt 133 1779B–ATARM–22-Mar-02 USART Interrupt Disable Register Name: Access Type: Offset: US_IDR Write-only 0x0C 31 30 29 28 27 26 25 24 COMMRX COMMTX – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – TXEMPTY TIMEOUT 7 6 5 4 3 2 1 0 PARE FRAME OVRE ENDTX ENDRX RXBRK TXRDY RXRDY • RXRDY: Disable RXRDY Interrupt (Code Label US_RXRDY) 0 = No effect. 1 = Disables RXRDY Interrupt. • TXRDY: Disable TXRDY Interrupt (Code Label US_TXRDY) 0 = No effect. 1 = Disables TXRDY Interrupt. • RXBRK: Disable Receiver Break Interrupt (Code Label US_RXBRK) 0 = No effect. 1 = Disables Receiver Break Interrupt. • ENDRX: Disable End of Receive Transfer Interrupt (Code Label US_ENDRX) 0 = No effect. 1 = Disables End of Receive Transfer Interrupt. • ENDTX: Disable End of Transmit Transfer Interrupt (Code Label US_ENDTX) 0 = No effect. 1 = Disables End of Transmit Transfer Interrupt. • OVRE: Disable Overrun Error Interrupt (Code Label US_OVRE) 0 = No effect. 1 = Disables Overrun Error Interrupt. • FRAME: Disable Framing Error Interrupt (Code Label US_FRAME) 0 = No effect. 1 = Disables Framing Error Interrupt. • PARE: Disable Parity Error Interrupt (Code Label US_PARE) 0 = No effect. 1 = Disables Parity Error Interrupt. • TIMEOUT: Disable Time-out Interrupt (Code Label US_TIMEOUT) 0 = No effect. 1 = Disables Receiver Time-out Interrupt. • TXEMPTY: Disable TXEMPTY Interrupt (Code Label US_TXEMPTY) 0 = No effect. 1 = Disables TXEMPTY Interrupt. • COMMTX: Disable ARM7TDMI ICE Debug Communication Channel Transmit Interrupt This bit is implemented for USART0 only. 0 = No effect. 1 = Disables COMMTX Interrupt. • COMMRX: Disable ARM7TDMI ICE Debug Communication Channel Receive Interrupt This bit is implemented for USART0 only. 0 = No effect. 1 = Disables COMMRX Interrupt. 134 AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A USART Interrupt Mask Register Name: Access Type: Offset: Reset Value: US_IMR Read-only 0x10 0x0 31 30 29 28 27 26 25 24 COMMRX COMMTX – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – TXEMPTY TIMEOUT 7 6 5 4 3 2 1 0 PARE FRAME OVRE ENDTX ENDRX RXBRK TXRDY RXRDY • RXRDY: RXRDY Interrupt Mask (Code Label US_RXRDY) 0 = RXRDY Interrupt is Disabled. 1 = RXRDY Interrupt is Enabled. • TXRDY: TXRDY Interrupt Mask (Code Label US_TXRDY) 0 = TXRDY Interrupt is Disabled. 1 = TXRDY Interrupt is Enabled. • RXBRK: Receiver Break Interrupt Mask (Code Label US_RXBRK) 0 = Receiver Break Interrupt is Disabled. 1 = Receiver Break Interrupt is Enabled. • ENDRX: End of Receive Transfer Interrupt Mask (Code Label US_ENDRX) 0 = End of Receive Transfer Interrupt is Disabled. 1 = End of Receive Transfer Interrupt is Enabled. • ENDTX: End of Transmit Transfer Interrupt Mask (Code Label US_ENDTX) 0 = End of Transmit Transfer Interrupt is Disabled. 1 = End of Transmit Transfer Interrupt is Enabled. • OVRE: Overrun Error Interrupt Mask (Code Label US_OVRE) 0 = Overrun Error Interrupt is Disabled. 1 = Overrun Error Interrupt is Enabled. • FRAME: Framing Error Interrupt Mask (Code Label US_FRAME) 0 = Framing Error Interrupt is Disabled. 1 = Framing Error Interrupt is Enabled. • PARE: Parity Error Interrupt Mask (Code Label US_PARE) 0 = Parity Error Interrupt is Disabled. 1 = Parity Error Interrupt is Enabled. • TIMEOUT: Time-out Interrupt Mask (Code Label US_TIMEOUT) 0 = Receive Time-out Interrupt is Disabled. 1 = Receive Time-out Interrupt is Enabled. • TXEMPTY: TXEMPTY Interrupt Mask (Code Label US_TXEMPTY) 0 = TXEMPTY Interrupt is Disabled. 1 = TXEMPTY Interrupt is Enabled. • COMMTX: ARM7TDMI ICE Debug Communication Channel Transmit Interrupt Mask This bit is implemented for USART0 only. 0 = COMMTX Interrupt is Disabled 1 = COMMTX Interrupt is Enabled • COMMRX: ARM7TDMI ICE Debug Communication Channel Receive Interrupt Mask This bit is implemented for USART0 only. 0 = COMMRX Interrupt is Disabled 1 = COMMRX Interrupt is Enabled 135 1779B–ATARM–22-Mar-02 USART Channel Status Register Name: Access Type: Offset: Reset Value: US_CSR Read-only 0x14 0x18 31 30 29 28 27 26 25 24 COMMRX COMMTX – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – TXEMPTY TIMEOUT 7 6 5 4 3 2 1 0 PARE FRAME OVRE ENDTX ENDRX RXBRK TXRDY RXRDY • RXRDY: Receiver Ready (Code Label US_RXRDY) 0 = No complete character has been received since the last read of the US_RHR or the receiver is disabled. If characters were being received when the receiver was disabled, RXRDY changes to 1 when the receiver is enabled. 1 = At least one complete character has been received and the US_RHR has not yet been read. • TXRDY: Transmitter Ready (Code Label US_TXRDY) 0 = A character is in the US_THR waiting to be transferred to the Transmit Shift Register, or an STTBRK command has been requested, or the transmitter is disabled. As soon as the transmitter is enabled, TXRDY becomes 1. 1 = US_THR is empty and there is no Break request pending TSR availability. Equal to zero when the USART is disabled or at reset. Transmitter Enable command (in US_CR) sets this bit to one. • RXBRK: Break Received/End of Break (Code Label US_RXBRK) 0 = No Break Received nor End of Break detected since the last “Reset Status Bits” command in the Control Register. 1 = Break Received or End of Break detected since the last “Reset Status Bits” command in the Control Register. • ENDRX: End of Receive Transfer (Code Label US_ENDRX) 0 = The End of Transfer signal from the Peripheral Data Controller channel dedicated to the receiver is inactive. 1 = The End of Transfer signal from the Peripheral Data Controller channel dedicated to the receiver is active. • ENDTX: End of Transmit Transfer (Code Label US_ENDTX) 0 = The End of Transfer signal from the Peripheral Data Controller channel dedicated to the transmitter is inactive. 1 = The End of Transfer signal from the Peripheral Data Controller channel dedicated to the transmitter is active. • OVRE: Overrun Error (Code Label US_OVRE) 0 = No byte has been transferred from the Receive Shift Register to the US_RHR when RxRDY was asserted since the last “Reset Status Bits” command. 1 = At least one byte has been transferred from the Receive Shift Register to the US_RHR when RxRDY was asserted since the last “Reset Status Bits” command. • FRAME: Framing Error (Code Label US_FRAME) 0 = No stop bit has been detected low since the last “Reset Status Bits” command. 1 = At least one stop bit has been detected low since the last “Reset Status Bits” command. • PARE: Parity Error (Code Label US_PARE) 1 = At least one parity bit has been detected false (or a parity bit high in multi-drop mode) since the last “Reset Status Bits” command. 0 = No parity bit has been detected false (or a parity bit high in multi-drop mode) since the last “Reset Status Bits” command. • TIMEOUT: Receiver Time-out (Code Label US_TIMEOUT) 0 = There has not been a time-out since the last “Start Time-out” command or the Time-out Register is 0. 1 = There has been a time-out since the last “Start Time-out” command. 136 AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A • TXEMPTY: Transmitter Empty (Code Label US_TXEMPTY) 0 = There are characters in either US_THR or the Transmit Shift Register, or the transmitter is disabled. 1 = There are no characters in either US_THR or the Transmit Shift Register. TXEMPTY is 1 after Parity, Stop Bit and Time-guard have been transmitted. TXEMPTY is 1 after stop bit has been sent, or after Time-guard has been sent if US_TTGR is not 0. Equal to zero when the USART is disabled or at reset. Transmitter Enable command (in US_CR) sets this bit to one, if the transmitter is disabled. • COMMTX: ARM7TDMI ICE Debug Communication Channel Transmit Status For USART0 only. Refer to the ARM7TDMI Datasheet for a complete description of this flag. • COMMRX: ARM7TDMI ICE Debug Communication Channel Receive Status For USART0 only. Refer to the ARM7TDMI Datasheet for a complete description of this flag. USART Receiver Holding Register Name: Access Type: Offset: Reset Value: US_RHR Read-only 0x18 0x0 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – RXCHR 7 6 5 4 3 2 1 0 RXCHR • RXCHR: Received Character Last character received if RXRDY is set. When number of data bits is less than 9 bits, the bits are right-aligned. All unused bits read zero. 137 1779B–ATARM–22-Mar-02 USART Transmitter Holding Register Name: Access Type: Offset: US_THR Write-only 0x1C 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – TXCHR 7 6 5 4 3 2 1 0 TXCHR • TXCHR: Character to be Transmitted Next character to be transmitted after the current character if TXRDY is not set. When number of data bits is less than 9 bits, the bits are right-aligned. USART Baud Rate Generator Register Name: Access Type: Offset: Reset Value: US_BRGR Read/Write 0x20 0x0 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 3 2 1 0 CD 7 6 5 4 CD • CD: Clock Divisor This register has no effect if Synchronous Mode is selected with an external clock. CD 0 Disables Clock 1 Clock Divisor Bypass (1) 2 to 65535 Notes: 138 Baud Rate (Asynchronous Mode (2)) = Selected Clock/(16 x CD) Baud Rate (Synchronous Mode) = Selected Clock/CD 1. In Synchronous mode, the value programmed must be even to ensure a 50:50 mark:space ratio. 2. Clock divisor bypass (CD = 1) must not be used when internal clock MCK is selected (USCLKS = 0). AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A USART Receiver Time-out Register Name: Access Type: Offset: Reset Value: US_RTOR Read/Write 0x24 0x0 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 TO • TO: Time-out Value When a value is written to this register, a Start Time-out Command is automatically performed. TO 0 Disables the RX Time-out function. 1- 255 The Time-out counter is loaded with TO when the Start Time-out Command is given or when each new data character is received (after reception has started). Time-out duration = TO x 4 x Bit period USART Transmitter Time-guard Register Name: Access Type: Offset: Reset Value: US_TTGR Read/Write 0x28 0x0 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 TG • TG: Time-guard Value TG 0 1 - 255 Disables the TX Time-guard function. TXD is inactive high after the transmission of each character for the time-guard duration. Time-guard duration = TG x Bit period 139 1779B–ATARM–22-Mar-02 USART Receive Pointer Register Name: Access Type: Offset: Reset Value: 31 US_RPR Read/Write 0x30 0x0 30 29 28 27 26 25 24 19 18 17 16 11 10 9 8 3 2 1 0 RXPTR 23 22 21 20 RXPTR 15 14 13 12 RXPTR 7 6 5 4 RXPTR • RXPTR: Receive Pointer RXPTR must be loaded with the address of the receive buffer. USART Receive Counter Register Name: Access Type: Offset: Reset Value: US_RCR Read/Write 0x34 0x0 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 3 2 1 0 RXCTR 7 6 5 4 RXCTR • RXCTR: Receive Counter RXCTR must be loaded with the size of the receive buffer. 0: Stop Peripheral Data Transfer dedicated to the receiver. 1-65535: Start Peripheral Data transfer if RXRDY is active. 140 AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A USART Transmit Pointer Register Name: Access Type: Offset: Reset Value: 31 US_TPR Read/Write 0x38 0x0 30 29 28 27 26 25 24 19 18 17 16 11 10 9 8 3 2 1 0 TXPTR 23 22 21 20 TXPTR 15 14 13 12 TXPTR 7 6 5 4 TXPTR • TXPTR: Transmit Pointer TXPTR must be loaded with the address of the transmit buffer. USART Transmit Counter Register Name: Access Type: Offset: Reset Value: US_TCR Read/Write 0x3C 0x0 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 3 2 1 0 TXCTR 7 6 5 4 TXCTR • TXCTR: Transmit Counter TXCTR must be loaded with the size of the transmit buffer. 0: Stop Peripheral Data Transfer dedicated to the transmitter. 1-65535: Start Peripheral Data transfer if TXRDY is active. 141 1779B–ATARM–22-Mar-02 TC: Timer/Counter The AT91M42800A features two Timer/Counter blocks, each containing three identical 16-bit Timer/Counter channels. Each channel can be independently programmed to perform a wide range of functions including frequency measurement, event counting, interval measurement, pulse generation, delay timing and pulse width modulation. Each Timer/Counter (TC) channel has 3 external clock inputs, 5 internal clock inputs, and 2 multi-purpose input/output signals which can be configured by the user. Each channel drives an internal interrupt signal which can be programmed to generate processor interrupts via the AIC (Advanced Interrupt Controller). The Timer/Counter block has two global registers which act upon all three TC channels. The Block Control Register allows the three channels to be started simultaneously with the same instruction. The Block Mode Register defines the external clock inputs for each Timer/Counter channel, allowing them to be chained. Each Timer/Counter block operates independently and has a complete set of block and channel registers. Since they are identical in operation, only one block is described below (see Timer/Counter Description on page 144). The internal configuration of a single Timer/Counter Block is shown in Figure 55. Figure 55. TC Block Diagram Parallel IO Controller MCK/2 TCLK0 MCK/8 TIOA1 TIOA2 XC0 MCK/32 XC1 TCLK1 Timer/Counter Channel 0 TIOA TIOA0 TIOB0 TIOA0 TIOB MCK/128 XC2 TCLK2 TC0XC0S SLCK TIOB0 SYNC TCLK0 TCLK1 TCLK2 INT TCLK0 XC0 TCLK1 TIOA0 XC1 Timer/Counter Channel 1 TIOA TIOA1 TIOB1 TIOA1 TIOB TIOA2 TCLK2 XC2 TC1XC1S TCLK0 XC0 TCLK1 XC1 TIOB1 SYNC Timer/Counter Channel 2 INT TIOA TIOA2 TIOB2 TIOA2 TIOB TCLK2 XC2 TIOA0 TIOA1 TC2XC2S TIOB2 SYNC INT Timer Counter Block Advanced Interrupt Controller 142 AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A Signal Name Description(1, 2) Channel Signals XC0, XC1, XC2 External Clock Inputs TIOA Capture Mode: General-purpose Input Waveform Mode: General-purpose Output TIOB Capture Mode: General-purpose Input Waveform Mode: General-purpose Input/Output INT SYNC Block 0 Signals TCLK0, TCLK1, TCLK2 Interrupt Signal Output Synchronization Input Signal Description External Clock Inputs for Channels 0, 1, 2 TIOA0 TIOA Signal for Channel 0 TIOB0 TIOB Signal for Channel 0 TIOA1 TIOA Signal for Channel 1 TIOB1 TIOB Signal for Channel 1 TIOA2 TIOA Signal for Channel 2 TIOB2 TIOB Signal for Channel 2 Block 1 Signals TCLK3, TCLK4, TCLK5 Notes: Description Description External Clock Inputs for Channels 3, 4, 5 TIOA3 TIOA Signal for Channel 3 TIOB3 TIOB Signal for Channel 3 TIOA4 TIOA Signal for Channel 4 TIOB4 TIOB Signal for Channel 4 TIOA5 TIOA Signal for Channel 5 TIOB5 TIOB Signal for Channel 5 1. After a hardware reset, the TC clock is disabled by default (see “PMC: Power Management Controller” on page 55). The user must configure the Power Management Controller before any access to the User Interface of the TC. 2. After a hardware reset, the Timer/Counter block pins are controlled by the PIO Controller. They must be configured to be controlled by the peripheral before being used. 143 1779B–ATARM–22-Mar-02 Timer/Counter Description Each Timer/Counter channel is identical in operation. The registers for channel programming are listed in Table 19. Counter Each Timer/Counter channel is organized around a 16-bit counter. The value of the counter is incremented at each positive edge of the input clock. When the counter reaches the value 0xFFFF and passes to 0x0000, an overflow occurs and the bit COVFS in TC_SR (Status Register) is set. The current value of the counter is accessible in real time by reading TC_CV. The counter can be reset by a trigger. In this case, the counter value passes to 0x0000 on the next valid edge of the clock. Clock Selection At block level, input clock signals of each channel can either be connected to the external inputs TCLK0, TCLK1 or TCLK2, or be connected to the configurable I/O signals TIOA0, TIOA1 or TIOA2 for chaining by programming the TC_BMR (Block mode). Each channel can independently select an internal or external clock source for its counter: • Internal clock signals: MCK/2, MCK/8, MCK/32, MCK/128 and Slow Clock SLCK • External clock signals: XC0, XC1 or XC2 The selected clock can be inverted with the CLKI bit in TC_CMR (Channel mode). This allows counting on the opposite edges of the clock. The burst function allows the clock to be validated when an external signal is high. The BURST parameter in the Mode Register defines this signal (none, XC0, XC1, XC2). Note: In all cases, if an external clock is used, the duration of each of its levels must be longer than the system clock (MCK) period. The external clock frequency must be at least 2.5 times lower than the system clock. Figure 56. Clock Selection CLKS CLKI MCK/2 MCK/8 MCK/32 MCK/128 Selected Clock SLCK XC0 XC1 XC2 BURST 1 144 AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A Clock Control The clock of each counter can be controlled in two different ways: it can be enabled/disabled and started/stopped. • The clock can be enabled or disabled by the user with the CLKEN and the CLKDIS commands in the Control Register. In Capture Mode it can be disabled by an RB load event if LDBDIS is set to 1 in TC_CMR. In Waveform Mode, it can be disabled by an RC Compare event if CPCDIS is set to 1 in TC_CMR. When disabled, the start or the stop actions have no effect: only a CLKEN command in the Control Register can re-enable the clock. When the clock is enabled, the CLKSTA bit is set in the Status Register. • The clock can also be started or stopped: a trigger (software, synchro, external or compare) always starts the clock. The clock can be stopped by an RB load event in Capture Mode (LDBSTOP = 1 in TC_CMR) or a RC compare event in Waveform Mode (CPCSTOP = 1 in TC_CMR). The start and the stop commands have effect only if the clock is enabled. Figure 57. Clock Control Selected Clock Trigger CLKSTA Q Q S CLKEN CLKDIS S R R Counter Clock Timer/Counter Operating Modes Stop Event Disable Event Each Timer/Counter channel can independently operate in two different modes: • Capture mode allows measurement on signals • Waveform mode allows wave generation The Timer/Counter mode is programmed with the WAVE bit in the TC Mode Register. In Capture mode, TIOA and TIOB are configured as inputs. In Waveform mode, TIOA is always configured to be an output and TIOB is an output if it is not selected to be the external trigger. Trigger A trigger resets the counter and starts the counter clock. Three types of triggers are common to both modes, and a fourth external trigger is available to each mode. The following triggers are common to both modes: • Software Trigger: Each channel has a software trigger, available by setting SWTRG in TC_CCR. 145 1779B–ATARM–22-Mar-02 • SYNC: Each channel has a synchronization signal SYNC. When asserted, this signal has the same effect as a software trigger. The SYNC signals of all channels are asserted simultaneously by writing TC_BCR (Block Control) with SYNC set. • Compare RC Trigger: RC is implemented in each channel and can provide a trigger when the counter value matches the RC value if CPCTRG is set in TC_CMR. The Timer/Counter channel can also be configured to have an external trigger. In Capture Mode, the external trigger signal can be selected between TIOA and TIOB. In Waveform Mode, an external event can be programmed on one of the following signals: TIOB, XC0, XC1 or XC2. This external event can then be programmed to perform a trigger by setting ENETRG in TC_CMR. If an external trigger is used, the duration of the pulses must be longer than the system clock (MCK) period in order to be detected. Capture Operating Mode This mode is entered by clearing the WAVE parameter in TC_CMR (Channel Mode Register). Capture Mode allows the TC Channel to perform measurements such as pulse timing, frequency, period, duty cycle and phase on TIOA and TIOB signals which are considered as input. Figure 58 shows the configuration of the TC Channel when programmed in Capture Mode. Capture Registers A and B (RA and RB) Registers A and B are used as capture registers. This means that they can be loaded with the counter value when a programmable event occurs on the signal TIOA. The parameter LDRA in TC_CMR defines the TIOA edge for the loading of register A, and the parameter LDRB defines the TIOA edge for the loading of Register B. RA is loaded only if it has not been loaded since the last trigger or if RB has been loaded since the last loading of RA. RB is loaded only if RA has been loaded since the last trigger or the last loading of RB. Loading RA or RB before the read of the last value loaded sets the Overrun Error Flag (LOVRS) in TC_SR (Status Register). In this case, the old value is overwritten. Trigger Conditions In addition to the SYNC signal, the software trigger and the RC compare trigger, an external trigger can be defined. Bit ABETRG in TC_CMR selects input signal TIOA or TIOB as an external trigger. Parameter ETRGEDG defines the edge (rising, falling or both) detected to generate an external trigger. If ETRGEDG = 0 (none), the external trigger is disabled. 146 AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A Status Register The following bits in the status register are significant in Capture Operating mode. • CPCS: RC Compare Status There has been an RC Compare match at least once since the last read of the status • COVFS: Counter Overflow Status The counter has attempted to count past $FFFF since the last read of the status • LOVRS: Load Overrun Status RA or RB has been loaded at least twice without any read of the corresponding register, since the last read of the status • LDRAS: Load RA Status RA has been loaded at least once without any read, since the last read of the status • LDRBS: Load RB Status RB has been loaded at least once without any read, since the last read of the status • ETRGS: External Trigger Status An external trigger on TIOA or TIOB has been detected since the last read of the status 147 1779B–ATARM–22-Mar-02 Figure 58. Capture Mode 148 AT91M42800A TCCLKS CLKSTA CLKI CLKEN CLKDIS MCK/2 MCK/8 MCK/32 Q S MCK/128 SLCK Q XC0 R S R XC1 XC2 LDBSTOP LDBDIS BURST Register C Capture Register A 1 SWTRG Capture Register B Compare RC = 16-bit Counter CLK OVF RESET SYNC Trig ABETRG CPCTRG ETRGEDG MTIOB Edge Detector INT CPCS Timer Counter Channel LOVRS LDRBS If RA is loaded COVFS Edge Detector LDRAS 1779B–ATARM–22-Mar-02 TIOA Edge Detector TC_IMR If RA is not loaded or RB is loaded LDRB ETRGS MTIOA LDRA TC_SR TIOB AT91M42800A Waveform Operating Mode This mode is entered by setting the WAVE parameter in TC_CMR (Channel Mode Register). Waveform Operating Mode allows the TC Channel to generate 1 or 2 PWM signals with the same frequency and independently programmable duty cycles, or to generate different types of one-shot or repetitive pulses. In this mode, TIOA is configured as output and TIOB is defined as output if it is not used as an external event (EEVT parameter in TC_CMR). Figure 59 shows the configuration of the TC Channel when programmed in Waveform Operating Mode. Compare Register A, B and C (RA, RB, and RC) In Waveform Operating Mode, RA, RB and RC are all used as compare registers. RA Compare is used to control the TIOA output. RB Compare is used to control the TIOB (if configured as output). RC Compare can be programmed to control TIOA and/or TIOB outputs. RC Compare can also stop the counter clock (CPCSTOP = 1 in TC_CMR) and/or disable the counter clock (CPCDIS = 1 in TC_CMR). As in Capture Mode, RC Compare can also generate a trigger if CPCTRG = 1. Trigger resets the counter so RC can control the period of PWM waveforms. External Event/Trigger Conditions An external event can be programmed to be detected on one of the clock sources (XC0, XC1, XC2) or TIOB. The external event selected can then be used as a trigger. The parameter EEVT in TC_CMR selects the external trigger. The parameter EEVTEDG defines the trigger edge for each of the possible external triggers (rising, falling or both). If EEVTEDG is cleared (none), no external event is defined. If TIOB is defined as an external event signal (EEVT = 0), TIOB is no longer used as output and the TC channel can only generate a waveform on TIOA. When an external event is defined, it can be used as a trigger by setting bit ENETRG in TC_CMR. As in Capture Mode, the SYNC signal, the software trigger and the RC compare trigger are also available as triggers. Output Controller The output controller defines the output level changes on TIOA and TIOB following an event. TIOB control is used only if TIOB is defined as output (not as an external event). The following events control TIOA and TIOB: software trigger, external event and RC compare. RA compare controls TIOA and RB compare controls TIOB. Each of these events can be programmed to set, clear or toggle the output as defined in the corresponding parameter in TC_CMR. 149 1779B–ATARM–22-Mar-02 The tables below show which parameter in TC_CMR is used to define the effect of each event. Parameter TIOA Event ASWTRG Software Trigger AEEVT External Event ACPC RC Compare ACPA RA Compare Parameter TIOB Event BSWTRG Software Trigger BEEVT External Event BCPC RC Compare BCPB RB Compare If two or more events occur at the same time, the priority level is defined as follows: 1. Software Trigger 2. External Event 3. RC Compare 4. RA or RB Compare Status The following bits in the status register are significant in Waveform mode: • CPAS: RA Compare Status There has been a RA Compare match at least once since the last read of the status • CPBS: RB Compare Status There has been a RB Compare match at least once since the last read of the status • CPCS: RC Compare Status There has been a RC Compare match at least once since the last read of the status • COVFS: Counter Overflow Counter has attempted to count past $FFFF since the last read of the status • ETRGS: External Trigger External trigger has been detected since the last read of the status 150 AT91M42800A 1779B–ATARM–22-Mar-02 Figure 59. Waveform Mode 1779B–ATARM–22-Mar-02 TCCLKS CLKSTA MCK/2 CLKEN CLKDIS ACPC CLKI MCK/8 Q S MCK/128 CPCDIS SLCK Q XC0 R S ACPA R XC1 XC2 CPCSTOP AEEVT MTIOA Output Controller MCK/32 TIOA BURST Register A Register B Register C Compare RA = Compare RB = Compare RC = ASWTRG 1 16-bit Counter CLK RESET SWTRG OVF BCPC SYNC Trig MTIOB EEVT BEEVT TIOB CPBS CPCS CPAS COVFS BSWTRG TC_IMR TIOB TC_SR Edge Detector ENETRG ETRGS EEVTEDG Output Controller BCPB CPCTRG INT 151 AT91M42800A Timer Counter Channel TC User Interface TC Block 0 Base Address: TC Block 1 Base Address: 0xFFFD0000 (Code Label TCB0_BASE) 0xFFFD4000 (Code Label TCB1_BASE) Table 18. TC Global Memory Map Offset Channel/Register Name Access Reset State 0x00 TC Channel 0 See Table 19 0x40 TC Channel 1 See Table 19 0x80 TC Channel 2 See Table 19 0xC0 TC Block Control Register TC_BCR Write-only – 0xC4 TC Block Mode Register TC_BMR Read/Write 0 TC_BCR (Block Control Register) and TC_BMR (Block Mode Register) control the TC block. TC Channels are controlled by the registers listed in Table 19. The offset of each of the Channel registers in Table 19 is in relation to the offset of the corresponding channel as mentioned in Table 18. Table 19. TC Channel Memory Map Offset Note: 152 Register Name Access Reset State 0x00 Channel Control Register TC_CCR Write-only – 0x04 Channel Mode Register TC_CMR Read/Write 0 0x08 Reserved – 0x0C Reserved – 0x10 Counter Value TC_CV Read/Write 0 (1) 0 0x14 Register A TC_RA Read/Write 0x18 Register B TC_RB Read/Write(1) 0 0x1C Register C TC_RC Read/Write 0 0x20 Status Register TC_SR Read-only – 0x24 Interrupt Enable Register TC_IER Write-only – 0x28 Interrupt Disable Register TC_IDR Write-only – 0x2C Interrupt Mask Register TC_IMR Read-only 0 1. Read-only if WAVE = 0 AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A TC Block Control Register Register Name: Access Type: Offset: TC_BCR Write-only 0xC0 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – – – SYNC • SYNC: Synchro Command (Code Label TC_SYNC) 0 = No effect. 1 = Asserts the SYNC signal which generates a software trigger simultaneously for each of the channels. 153 1779B–ATARM–22-Mar-02 TC Block Mode Register Register Name: Access Type: Offset: Reset Value: TC_BMR Read/Write 0xC4 0x0 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 – – TC2XC2S TC1XC1S 0 TC0XC0S • TC0XC0S: External Clock Signal 0 Selection TC0XC0S Signal Connected to XC0 Code Label: TC_TC0XC0S 0 0 TCLK0 TC_TCLK0XC0 0 1 None TC_NONEXC0 1 0 TIOA1 TC_TIOA1XC0 1 1 TIOA2 TC_TIOA2XC0 • TC1XC1S: External Clock Signal 1 Selection TC1XC1S Signal Connected to XC1 Code Label: TC_TC1XC1S 0 0 TCLK1 TC_TCLK1XC1 0 1 None TC_NONEXC1 1 0 TIOA0 TC_TIOA0XC1 1 1 TIOA2 TC_TIOA2XC1 • TC2XC2S: External Clock Signal 2 Selection TC2XC2S 154 Signal Connected to XC2 Code Label: TC_TC2XC2S 0 0 TCLK2 TC_TCLK2XC2 0 1 None TC_NONEXC2 1 0 TIOA0 TC_TIOA0XC2 1 1 TIOA1 TC_TIOA1XC2 AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A TC Channel Control Register Register Name: Access Type: Offset: TC_CCR Write-only 0x00 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – – – – SWTRG CLKDIS CLKEN • CLKEN: Counter Clock Enable Command (Code Label TC_CLKEN) 0 = No effect. 1 = Enables the clock if CLKDIS is not 1. • CLKDIS: Counter Clock Disable Command (Code Label TC_CLKDIS) 0 = No effect. 1 = Disables the clock. • SWTRG: Software Trigger Command (Code Label TC_SWTRG) 0 = No effect. 1 = A software trigger is performed: the counter is reset and clock is started. 155 1779B–ATARM–22-Mar-02 TC Channel Mode Register: Capture Mode Register Name: Access Type: Offset: Reset Value: TC_CMR Read/Write 0x04 0x0 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 – – – – 15 14 13 12 11 10 WAVE=0 CPCTRG – – – ABETRG 7 6 5 3 2 LDBDIS LDBSTOP 4 BURST 16 LDRB LDRA CLKI 9 8 ETRGEDG 1 0 TCCLKS • TCCLKS: Clock Selection TCCLKS Clock Selected Code Label: TC_CLKS 0 0 0 MCK/2 TC_CLKS_MCK2 0 0 1 MCK/8 TC_CLKS_MCK8 0 1 0 MCK/32 TC_CLKS_MCK32 0 1 1 MCK/128 TC_CLKS_MCK128 1 0 0 SLCK TC_CLKS_SLCK 1 0 1 XC0 TC_CLKS_XC0 1 1 0 XC1 TC_CLKS_XC1 1 1 1 XC2 TC_CLKS_XC2 • CLKI: Clock Invert (Code Label TC_CLKI) 0 = Counter is incremented on rising edge of the clock. 1 = Counter is incremented on falling edge of the clock. • BURST: Burst Signal Selection BURST Selected BURST Code Label: TC_BURST 0 0 The clock is not gated by an external signal. TC_BURST_NONE 0 1 XC0 is ANDed with the selected clock. TC_BURST_XC0 1 0 XC1 is ANDed with the selected clock. TC_BURST_XC1 1 1 XC2 is ANDed with the selected clock. TC_BURST_XC2 • LDBSTOP: Counter Clock Stopped with RB Loading (Code Label TC_LDBSTOP) 0 = Counter clock is not stopped when RB loading occurs. 1 = Counter clock is stopped when RB loading occurs. • LDBDIS: Counter Clock Disable with RB Loading (Code Label TC_LDBDIS) 0 = Counter clock is not disabled when RB loading occurs. 1 = Counter clock is disabled when RB loading occurs. 156 AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A • ETRGEDG: External Trigger Edge Selection ETRGEDG Edge Code Label: TC_ETRGEDG 0 0 None TC_ETRGEDG_EDGE_NONE 0 1 Rising edge TC_ETRGEDG_RISING_EDGE 1 0 Falling edge TC_ETRGEDG_FALLING_EDGE 1 1 Each edge TC_ETRGEDG_BOTH_EDGE • ABETRG: TIOA or TIOB External Trigger Selection ABETRG Selected ABETRG Code Label: TC_ABETRG 0 TIOB is used as an external trigger. TC_ABETRG_TIOB 1 TIOA is used as an external trigger. TC_ABETRG_TIOA • CPCTRG: RC Compare Trigger Enable (Code Label TC_CPCTRG) 0 = RC Compare has no effect on the counter and its clock. 1 = RC Compare resets the counter and starts the counter clock. • WAVE = 0 (Code Label TC_WAVE) 0 = Capture Mode is enabled. 1 = Capture Mode is disabled (Waveform Mode is enabled). • LDRA: RA Loading Selection LDRA Edge Code Label: TC_LDRA 0 0 None TC_LDRA_EDGE_NONE 0 1 Rising edge of TIOA TC_LDRA_RISING_EDGE 1 0 Falling edge of TIOA TC_LDRA_FALLING_EDGE 1 1 Each edge of TIOA TC_LDRA_BOTH_EDGE • LDRB: RB Loading Selection LDRB Edge Code Label: TC_LDRB 0 0 None TC_LDRB_EDGE_NONE 0 1 Rising edge of TIOA TC_LDRB_RISING_EDGE 1 0 Falling edge of TIOA TC_LDRB_FALLING_EDGE 1 1 Each edge of TIOA TC_LDRB_BOTH_EDGE 157 1779B–ATARM–22-Mar-02 TC Channel Mode Register: Waveform Mode Register Name: Access Type: Offset: Reset Value: TC_CMR Read/Write 0x04 0x0 31 30 29 BSWTRG 23 28 27 BEEVT 22 21 ASWTRG 26 25 24 BCPC 20 19 AEEVT BCPB 18 17 16 ACPC 15 14 13 12 WAVE=1 CPCTRG – ENETRG 7 6 5 CPCDIS CPCSTOP 4 BURST 11 ACPA 10 9 EEVT 3 8 EEVTEDG 2 CLKI 1 0 TCCLKS • TCCLKS: Clock Selection TCCLKS Clock Selected Code Label: TC_CLKS 0 0 0 MCK/2 TC_CLKS_MCK2 0 0 1 MCK/8 TC_CLKS_MCK8 0 1 0 MCK/32 TC_CLKS_MCK32 0 1 1 MCK/128 TC_CLKS_MCK128 1 0 0 SLCK TC_CLKS_SLCK 1 0 1 XC0 TC_CLKS_XC0 1 1 0 XC1 TC_CLKS_XC1 1 1 1 XC2 TC_CLKS_XC2 • CLKI: Clock Invert (Code Label TC_CLKI) 0 = Counter is incremented on rising edge of the clock. 1 = Counter is incremented on falling edge of the clock. • BURST: Burst Signal Selection BURST Selected BURST Code Label: TC_BURST 0 0 The clock is not gated by an external signal. TC_BURST_NONE 0 1 XC0 is ANDed with the selected clock. TC_BURST_XC0 1 0 XC1 is ANDed with the selected clock. TC_BURST_XC1 1 1 XC2 is ANDed with the selected clock. TC_BURST_XC2 • CPCSTOP: Counter Clock Stopped with RC Compare (Code Label TC_CPCSTOP) 0 = Counter clock is not stopped when counter reaches RC. 1 = Counter clock is stopped when counter reaches RC. • CPCDIS: Counter Clock Disable with RC Compare (Code Label TC_CPCDIS) 0 = Counter clock is not disabled when counter reaches RC. 1 = Counter clock is disabled when counter reaches RC. 158 AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A • EEVTEDG: External Event Edge Selection EEVTEDG Edge Code Label: TC_EEVTEDG 0 0 None TC_EEVTEDG_EDGE_NONE 0 1 Rising edge TC_EEVTEDG_RISING_EDGE 1 0 Falling edge TC_EEVTEDG_FALLING_EDGE 1 1 Each edge TC_EEVTEDG_BOTH_EDGE • EEVT: External Event Selection Signal Selected as External Event EEVT TIOB Direction (1) Code Label: TC_EEVT 0 0 TIOB Input 0 1 XC0 Output TC_EEVT_XC0 1 0 XC1 Output TC_EEVT_XC1 1 XC2 Output TC_EEVT_XC2 1 Note: TC_EEVT_TIOB If TIOB is chosen as the external event signal, it is configured as an input and no longer generates waveforms. • ENETRG: External Event Trigger Enable (Code Label TC_ENETRG) 0 = The external event has no effect on the counter and its clock. In this case, the selected external event only controls the TIOA output. 1 = The external event resets the counter and starts the counter clock. • CPCTRG: RC Compare Trigger Enable (Code Label TC_CPCTRG) 0 = RC Compare has no effect on the counter and its clock. 1 = RC Compare resets the counter and starts the counter clock. • WAVE = 1 (Code Label TC_WAVE) 0 = Waveform Mode is disabled (Capture Mode is enabled). 1 = Waveform Mode is enabled. • ACPA: RA Compare Effect on TIOA Effect Code Label: TC_ACPA 0 ACPA 0 None TC_ACPA_OUTPUT_NONE 0 1 Set TC_ACPA_SET_OUTPUT 1 0 Clear TC_ACPA_CLEAR_OUTPUT 1 1 Toggle TC_ACPA_TOGGLE_OUTPUT • ACPC: RC Compare Effect on TIOA ACPC Effect Code Label: TC_ACPC 0 0 None TC_ACPC_OUTPUT_NONE 0 1 Set TC_ACPC_SET_OUTPUT 1 0 Clear TC_ACPC_CLEAR_OUTPUT 1 1 Toggle TC_ACPC_TOGGLE_OUTPUT 159 1779B–ATARM–22-Mar-02 • AEEVT: External Event Effect on TIOA AEEVT Effect Code Label: TC_AEEVT 0 0 None TC_AEEVT_OUTPUT_NONE 0 1 Set TC_AEEVT_SET_OUTPUT 1 0 Clear TC_AEEVT_CLEAR_OUTPUT 1 1 Toggle TC_AEEVT_TOGGLE_OUTPUT • ASWTRG: Software Trigger Effect on TIOA ASWTRG Effect Code Label: TC_ASWTRG 0 0 None TC_ASWTRG_OUTPUT_NONE 0 1 Set TC_ASWTRG_SET_OUTPUT 1 0 Clear TC_ASWTRG_CLEAR_OUTPUT 1 1 Toggle TC_ASWTRG_TOGGLE_OUTPUT • BCPB: RB Compare Effect on TIOB BCPB Effect Code Label: TC_BCPB 0 0 None TC_BCPB_OUTPUT_NONE 0 1 Set TC_BCPB_SET_OUTPUT 1 0 Clear TC_BCPB_CLEAR_OUTPUT 1 1 Toggle TC_BCPB_TOGGLE_OUTPUT • BCPC: RC Compare Effect on TIOB BCPC Effect Code Label: TC_BCPC 0 0 None TC_BCPC_OUTPUT_NONE 0 1 Set TC_BCPC_SET_OUTPUT 1 0 Clear TC_BCPC_CLEAR_OUTPUT 1 1 Toggle TC_BCPC_TOGGLE_OUTPUT • BEEVT: External Event Effect on TIOB BEEVT Effect Code Label: TC_BEEVT 0 0 None TC_BEEVT_OUTPUT_NONE 0 1 Set TC_BEEVT_SET_OUTPUT 1 0 Clear TC_BEEVT_CLEAR_OUTPUT 1 1 Toggle TC_BEEVT_TOGGLE_OUTPUT • BSWTRG: Software Trigger Effect on TIOB BSWTRG 160 Effect Code Label: TC_BSWTRG 0 0 None TC_BSWTRG_OUTPUT_NONE 0 1 Set TC_BSWTRG_SET_OUTPUT 1 0 Clear TC_BSWTRG_CLEAR_OUTPUT 1 1 Toggle TC_BSWTRG_TOGGLE_OUTPUT AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A TC Counter Value Register Register Name: Access Type: Offset: Reset Value: TC_CV Read-only 0x10 0x0 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 3 2 1 0 CV 7 6 5 4 CV • CV: Counter Value (Code Label TC_CV) CV contains the counter value in real time. TC Register A Register Name: Access Type: Offset: Reset Value: TC_RA Read-only if WAVE = 0, Read/Write if WAVE = 1 0x14 0x0 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 3 2 1 0 RA 7 6 5 4 RA • RA: Register A (Code Label TC_RA) RA contains the Register A value in real time. 161 1779B–ATARM–22-Mar-02 TC Register B Register Name: Access Type: Offset: Reset Value: TC_RB Read-only if WAVE = 0, Read/Write if WAVE = 1 0x18 0x0 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 3 2 1 0 RB 7 6 5 4 RB • RB: Register B (Code Label TC_RB) RB contains the Register B value in real time. TC Register C Register Name: Access Type: Offset: Reset Value: TC_RC Read/Write 0x1C 0x0 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 3 2 1 0 RC 7 6 5 4 RC • RC: Register C (Code Label TC_RC) RC contains the Register C value in real time. 162 AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A TC Status Register Register Name: Access Type: Offset: TC_SR Read-only 0x20 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – MTIOB MTIOA CLKSTA 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 ETRGS LDRBS LDRAS CPCS CPBS CPAS LOVRS COVFS • COVFS: Counter Overflow Status (Code Label TC_COVFS) 0 = No counter overflow has occurred since the last read of the Status Register. 1 = A counter overflow has occurred since the last read of the Status Register. • LOVRS: Load Overrun Status (Code Label TC_LOVRS) 0 = Load overrun has not occurred since the last read of the Status Register or WAVE = 1. 1 = RA or RB have been loaded at least twice without any read of the corresponding register since the last read of the Status Register, if WAVE = 0. • CPAS: RA Compare Status (Code Label TC_CPAS) 0 = RA Compare has not occurred since the last read of the Status Register or WAVE = 0. 1 = RA Compare has occurred since the last read of the Status Register, if WAVE = 1. • CPBS: RB Compare Status (Code Label TC_CPBS) 0 = RB Compare has not occurred since the last read of the Status Register or WAVE = 0. 1 = RB Compare has occurred since the last read of the Status Register, if WAVE = 1. • CPCS: RC Compare Status (Code Label TC_CPCS) 0 = RC Compare has not occurred since the last read of the Status Register. 1 = RC Compare has occurred since the last read of the Status Register. • LDRAS: RA Loading Status (Code Label TC_LDRAS) 0 = RA Load has not occurred since the last read of the Status Register or WAVE = 1. 1 = RA Load has occurred since the last read of the Status Register, if WAVE = 0. • LDRBS: RB Loading Status (Code Label TC_LDRBS) 0 = RB Load has not occurred since the last read of the Status Register or WAVE = 1. 1 = RB Load has occurred since the last read of the Status Register, if WAVE = 0. • ETRGS: External Trigger Status (Code Label TC_ETRGS) 0 = External trigger has not occurred since the last read of the Status Register. 1 = External trigger has occurred since the last read of the Status Register. • CLKSTA: Clock Enabling Status (Code Label TC_CLKSTA) 0 = Clock is disabled. 1 = Clock is enabled. • MTIOA: TIOA Mirror (Code Label TC_MTIOA) 0 = TIOA is low. If WAVE = 0, this means that TIOA pin is low. If WAVE = 1, this means that TIOA is driven low. 1 = TIOA is high. If WAVE = 0, this means that TIOA pin is high. If WAVE = 1, this means that TIOA is driven high. • MTIOB: TIOB Mirror (Code Label TC_MTIOB) 0 = TIOB is low. If WAVE = 0, this means that TIOB pin is low. If WAVE = 1, this means that TIOB is driven low. 1 = TIOB is high. If WAVE = 0, this means that TIOB pin is high. If WAVE = 1, this means that TIOB is driven high. 163 1779B–ATARM–22-Mar-02 TC Interrupt Enable Register Register Name: Access Type: Offset: TC_IER Write-only 0x24 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 ETRGS LDRBS LDRAS CPCS CPBS CPAS LOVRS COVFS • COVFS: Counter Overflow (Code Label TC_COVFS) 0 = No effect. 1 = Enables the Counter Overflow Interrupt. • LOVRS: Load Overrun (Code Label TC_LOVRS) 0 = No effect. 1: Enables the Load Overrun Interrupt. • CPAS: RA Compare (Code Label TC_CPAS) 0 = No effect. 1 = Enables the RA Compare Interrupt. • CPBS: RB Compare (Code Label TC_CPBS) 0 = No effect. 1 = Enables the RB Compare Interrupt. • CPCS: RC Compare (Code Label TC_CPCS) 0 = No effect. 1 = Enables the RC Compare Interrupt. • LDRAS: RA Loading (Code Label TC_LDRAS) 0 = No effect. 1 = Enables the RA Load Interrupt. • LDRBS: RB Loading (Code Label TC_LDRBS) 0 = No effect. 1 = Enables the RB Load Interrupt. • ETRGS: External Trigger (Code Label TC_ETRGS) 0 = No effect. 1 = Enables the External Trigger Interrupt. 164 AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A TC Interrupt Disable Register Register Name: Access Type: Offset: TC_IDR Write-only 0x28 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 ETRGS LDRBS LDRAS CPCS CPBS CPAS LOVRS COVFS • COVFS: Counter Overflow (Code Label TC_COVFS) 0 = No effect. 1 = Disables the Counter Overflow Interrupt. • LOVRS: Load Overrun (Code Label TC_LOVRS) 0 = No effect. 1 = Disables the Load Overrun Interrupt (if WAVE = 0). • CPAS: RA Compare (Code Label TC_CPAS) 0 = No effect. 1 = Disables the RA Compare Interrupt (if WAVE = 1). • CPBS: RB Compare (Code Label TC_CPBS) 0 = No effect. 1 = Disables the RB Compare Interrupt (if WAVE = 1). • CPCS: RC Compare (Code Label TC_CPCS) 0 = No effect. 1 = Disables the RC Compare Interrupt. • LDRAS: RA Loading (Code Label TC_LDRAS) 0 = No effect. 1 = Disables the RA Load Interrupt (if WAVE = 0). • LDRBS: RB Loading (Code Label TC_LDRBS) 0 = No effect. 1 = Disables the RB Load Interrupt (if WAVE = 0). • ETRGS: External Trigger (Code Label TC_ETRGS) 0 = No effect. 1 = Disables the External Trigger Interrupt. 165 1779B–ATARM–22-Mar-02 TC Interrupt Mask Register Register Name: Access Type: Offset: Reset Value: TC_IMR Read-only 0x2C 0x0 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 ETRGS LDRBS LDRAS CPCS CPBS CPAS LOVRS COVFS • COVFS: Counter Overflow (Code Label TC_COVFS) 0 = The Counter Overflow Interrupt is disabled. 1 = The Counter Overflow Interrupt is enabled. • LOVRS: Load Overrun (Code Label TC_LOVRS) 0 = The Load Overrun Interrupt is disabled. 1 = The Load Overrun Interrupt is enabled. • CPAS: RA Compare (Code Label TC_CPAS) 0 = The RA Compare Interrupt is disabled. 1 = The RA Compare Interrupt is enabled. • CPBS: RB Compare (Code Label TC_CPBS) 0 = The RB Compare Interrupt is disabled. 1 = The RB Compare Interrupt is enabled. • CPCS: RC Compare (Code Label TC_CPCS) 0 = The RC Compare Interrupt is disabled. 1 = The RC Compare Interrupt is enabled. • LDRAS: RA Loading (Code Label TC_LDRAS) 0 = The Load RA Interrupt is disabled. 1 = The Load RA Interrupt is enabled. • LDRBS: RB Loading (Code Label TC_LDRBS) 0 = The Load RB Interrupt is disabled. 1 = The Load RB Interrupt is enabled. • ETRGS: External Trigger (Code Label TC_ETRGS) 0 = The External Trigger Interrupt is disabled. 1 = The External Trigger Interrupt is enabled. 166 AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A SPI: Serial Peripheral Interface The AT91M42800A includes two SPIs which provide communication with external devices in master or slave mode. They are independent, and are referred to by the letters A and B. Pin Description Seven pins are associated with the SPI Interface. When not needed for the SPI function, each of these pins can be configured as a PIO. Support for an external master is provided by the PIO Controller Multi-driver option. To configure an SPI pin as open-drain to support external drivers, set the corresponding bits in the PIO_MDSR register (see page 115). An input filter can be enabled on the SPI input pins by setting the corresponding bits in the PIO_IFSR (see page 109). The NPCS0/NSS pin can function as a peripheral chip select output or slave select input. Refer to Table 20 for a description of the SPI pins. Figure 60. SPI Block Diagram MCK Serial Peripheral Interface MCK/32 Parallel IO Controller MISO APB MISO MOSI MOSI SPCK SPCK NPCS0/NSS INT Generic Name NPCS0/NSS NPCS1 NPCS1 NPCS2 NPCS2 NPCS3 NPCS3 Advanced Interrupt Controller Table 20. SPI Pins Generic Mnemonic Mode Function Master In Slave Out MISO Master Slave Serial data input to SPI Serial data output from SPI Master Out Slave In MOSI Master Slave Serial data output from SPI Serial data input to SPI Serial Clock SPCK Master Slave Clock output from SPI Clock input to SPI Peripheral Chip Selects NPCS1NPCS3 Master Select peripherals Peripheral Chip Select/ Slave Select NPCS0/ NSS Master Master Slave Output: Selects peripheral Input: low causes mode fault Input: chip select for SPI Pin Name Notes: 1. After a hardware reset, the SPI clock is disabled by default (see “PMC: Power Management Controller” on page 55). The user must configure the Power Management Controller before any access to the User Interface of the SPI. 2. After a hardware reset, the SPI pins are deselected by default (see “PIO: Parallel I/O Controller” on page 98). The user must configure the PIO Controller to enable the corresponding pins for their SPI function. NPCS0/NSS must be configured as open-drain in the Parallel I/O Controller for multi-master operation. 167 1779B–ATARM–22-Mar-02 Master Mode In Master mode, the SPI controls data transfers to and from the slave(s) connected to the SPI bus. The SPI drives the chip select(s) to the slave(s) and the serial clock (SPCK). After enabling the SPI, a data transfer begins when the ARM core writes to the SP_TDR (Transmit Data Register). See Table 21. Transmit and Receive buffers maintain the data flow at a constant rate with a reduced requirement for high priority interrupt servicing. When new data is available in the SP_TDR (Transmit Data Register) the SPI continues to transfer data. If the SP_RDR (Receive Data Register) has not been read before new data is received, the Overrun Error (OVRES) flag is set. The delay between the activation of the chip select and the start of the data transfer (DLYBS) as well as the delay between each data transfer (DLYBCT) can be programmed for each of the four external chip selects. All data transfer characteristics including the two timing values are programmed in registers SP_CSR0 to SP_CSR3 (Chip Select Registers). See Table 21. In master mode the peripheral selection can be defined in two different ways: • Fixed Peripheral Select: SPI exchanges data with only one peripheral • Variable Peripheral Select: Data can be exchanged with more than one peripheral Figures 61 and 62 show the operation of the SPI in Master mode. For details concerning the flag and control bits in these diagrams, see the tables in the Programmer’s Model, starting on page 175. Fixed Peripheral Select This mode is ideal for transferring memory blocks without the extra overhead in the transmit data register to determine the peripheral. Fixed Peripheral Select is activated by setting bit PS to zero in SP_MR (Mode Register). The peripheral is defined by the PCS field, also in SP_MR. This option is only available when the SPI is programmed in master mode. Variable Peripheral Select Variable Peripheral Select is activated by setting bit PS to one. The PCS field in SP_TDR (Transmit Data Register) is used to select the destination peripheral. The data transfer characteristics are changed when the selected peripheral changes, according to the associated chip select register. The PCS field in the SP_MR has no effect. This option is only available when the SPI is programmed in master mode. Chip Selects The Chip Select lines are driven by the SPI only if it is programmed in Master mode. These lines are used to select the destination peripheral. The PCSDEC field in SP_MR (Mode Register) selects 1 to 4 peripherals (PCSDEC = 0) or up to 15 peripherals (PCSDEC = 1). If Variable Peripheral Select is active, the chip select signals are defined for each transfer in the PCS field in SP_TDR. Chip select signals can thus be defined independently for each transfer. If Fixed Peripheral Select is active, Chip Select signals are defined for all transfers by the field PCS in SP_MR. If a transfer with a new peripheral is necessary, the software must wait until the current transfer is completed, then change the value of PCS in SP_MR before writing new data in SP_TDR. The value on the NPCS pins at the end of each transfer can be read in the SP_RDR (Receive Data Register). By default, all NPCS signals are high (equal to one) before and after each transfer. 168 AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A Mode Fault Detection A mode fault is detected when the SPI is programmed in Master Mode and a low level is driven by an external master on the NPCSA/NSS signal. When a mode fault is detected, the MODF bit in the SP_SR is set until the SP_SR is read and the SPI is disabled until re-enabled by bit SPIEN in the SP_CR (Control Register). 169 1779B–ATARM–22-Mar-02 Figure 61. Functional Flow Diagram in Master Mode SPI Enable 1 TDRE 0 0 Fixed peripheral PS 1 Variable peripheral NPCS = SP_TDR(PCS) NPCS = SP_MR(PCS) Delay DLYBS Serializer = SP_TDR(TD) TDRE = 1 Data Transfer SP_RDR(RD) = Serializer RDRF = 1 Delay DLYBCT TDRE 1 0 0 Fixed peripheral PS NPCS = 0xF 1 Variable peripheral Delay DLYBCS SP_TDR(PCS) Same peripheral New peripheral NPCS = 0xF Delay DLYBCS NPCS = SP_TDR(PCS) 170 AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A Figure 62. SPI in Master Mode SP_MR(MCK32) MCK 0 1 SPI Master Clock SPIDIS SPIEN MCK/32 SPCK Clock Generator SP_CSRx[15:0] SPCK S Q R SP_RDR PCS RD MSB LSB Serializer MISO SP_TDR PCS MOSI TD NPCS3 NPCS2 NPCS1 SP_MR(PS) NPCS0 1 SP_MR(PCS) 0 SP_MR(MSTR) SP_SR M O D F T D R E R D R F O V R E S P I E N S SP_IER SP_IDR SP_IMR SPIRQ 171 1779B–ATARM–22-Mar-02 Slave Mode In Slave Mode, the SPI waits for NSS to go active low before receiving the serial clock from an external master. In slave mode CPOL, NCPHA and BITS fields of SP_CSR0 are used to define the transfer characteristics. The other Chip Select Registers are not used in slave mode. Figure 63. SPI in Slave Mode SPCK NSS SPIDIS SPIEN S Q R SP_RDR RD LSB MOSI MSB Serializer MISO SP_TDR TD SP_SR S P I E N S T D R E R D R F O V R E SP_IER SP_IDR SP_IMR SPIRQ 172 AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A Data Transfer The following waveforms show examples of data transfers. Figure 64. SPI Transfer Format (NCPHA = 1, 8 Bits per Transfer) 1 SPCK Cycle (for reference) 2 3 5 4 6 8 7 SPCK (CPOL = 0) SPCK (CPOL = 1) MOSI (from Master) MSB MISO (from Slave) MSB 6 5 4 3 2 1 LSB 6 5 4 3 2 1 LSB X NSS (to Slave) Figure 65. SPI Transfer Format (NCPHA = 0, 8 Bits per Transfer) 1 SPCK Cycle (for reference) 2 3 5 4 6 8 7 SPCK (CPOL = 0) SPCK (CPOL = 1) MOSI (from Master) MISO (from Slave) X MSB 6 5 4 3 2 1 MSB 6 5 4 3 2 1 LSB LSB NSS (to Slave) 173 1779B–ATARM–22-Mar-02 Figure 66. Programmable Delays (DLYBCS, DLYBS and DLYBCT) Chip Select 1 Change peripheral Chip Select 2 No change of peripheral SPCK Output DLYBCS Clock Generation DLYBS DLYBCT DLYBCT In Master Mode the SPI Master Clock is either MCK or MCK/32, as defined by the MCK32 field of SP_MR. The SPI baud rate clock is generated by dividing the SPI Master Clock by a value between 4 and 510. The divisor is defined in the SCBR field in each Chip Select Register. The transfer speed can thus be defined independently for each chip select signal. CPOL and NCPHA in the Chip Select Registers define the clock/data relationship between master and slave devices. CPOL defines the inactive value of the SPCK. NCPHA defines which edge causes data to change and which edge causes data to be captured. In Slave Mode, the input clock low and high pulse duration must strictly be longer than two system clock (MCK) periods. Peripheral Data Controller Each SPI is closely connected to two Peripheral Data Controller channels. One is dedicated to the receiver. The other is dedicated to the transmitter. The PDC channel is programmed using SP_TPR (Transmit Pointer) and SP_TCR (Transmit Counter) for the transmitter and SP_RPR (Receive Pointer) and SP_RCR (Receive Counter) for the receiver. The status of the PDC is given in SP_SR by the SPENDTX bit for the transmitter and by the SPENDRX bit for the receiver. The pointer registers (SP_TPR and SP_RPR) are used to store the address of the transmit or receive buffers. The counter registers (SP_TCR and SP_RCR) are used to store the size of these buffers. The receiver data transfer is triggered by the RDRF bit and the transmitter data transfer is triggered by TDRE. When a transfer is performed, the counter is decremented and the pointer is incremented. When the counter reaches 0, the status bit is set (SPENDRX for the receiver, SPENDTX for the transmitter in SP_SR) and can be programmed to generate an interrupt. While the counter is at zero, the status bit is asserted and transfers are disabled. 174 AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A SPI Programmer’s Model SPIA Base Address: 0xFFFC8000 SPIB Base Address: 0xFFFCC000 Table 21. SPI Memory Map Offset Register Name Access Reset State 0x00 Control Register SP_CR Write-only – 0x04 Mode Register SP_MR Read/Write 0 0x08 Receive Data Register SP_RDR Read-only 0 0x0C Transmit Data Register SP_TDR Write-only – 0x10 Status Register SP_SR Read-only 0 0x14 Interrupt Enable Register SP_IER Write-only – 0x18 Interrupt Disable Register SP_IDR Write-only – 0x1C Interrupt Mask Register SP_IMR Read-only 0 0x20 Receive Pointer Register SP_RPR Read/Write 0 0x24 Receive Counter Register SP_RCR Read/Write 0 0x28 Transmit Pointer Register SP_TPR Read/Write 0 0x2C Transmit Counter Register SP_TCR Read/Write 0 0x30 Chip Select Register 0 SP_CSR0 Read/Write 0 0x34 Chip Select Register 1 SP_CSR1 Read/Write 0 0x38 Chip Select Register 2 SP_CSR2 Read/Write 0 0x3C Chip Select Register 3 SP_CSR3 Read/Write 0 175 1779B–ATARM–22-Mar-02 SPI Control Register Register Name: Access Type: Offset: SP_CR Write-only 0x00 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 SWRST – – – – – SPIDIS SPIEN • SPIEN: SPI Enable (Code Label SP_SPIEN) 0 = No effect. 1 = Enables the SPI to transfer and receive data. • SPIDIS: SPI Disable (Code Label SP_SPIDIS) 0 = No effect. 1 = Disables the SPI. All pins are set in input mode and no data is received or transmitted. If a transfer is in progress, the transfer is finished before the SPI is disabled. If both SPIEN and SPIDIS are equal to one when the control register is written, the SPI is disabled. • SWRST: SPI Software reset (Code Label SP_SWRST) 0 = No effect. 1 = Resets the SPI. A software triggered hardware reset of the SPI interface is performed. 176 AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A SPI Mode Register Register Name: Access Type: Offset: Reset Value: 31 SP_MR Read/Write 0x04 0x0 30 29 28 27 26 19 18 25 24 17 16 DLYBCS 23 22 21 20 – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 LLB – – – MCK32 PCSDEC PS MSTR PCS • MSTR: Master/Slave Mode (Code Label SP_MSTR) 0 = SPI is in Slave mode. 1 = SPI is in Master mode. MSTR configures the SPI Interface for either master or slave mode operation. • PS: Peripheral Select PS Selected PS Code Label: SP_PS 0 Fixed Peripheral Select SP_PS_FIXED 1 Variable Peripheral Select SP_PS_VARIABLE • PCSDEC: Chip Select Decode (Code Label SP_PCSDEC) 0 = The chip selects are directly connected to a peripheral device. 1 = The four chip select lines are connected to a 4- to 16-bit decoder. When PCSDEC equals one, up to 16 Chip Select signals can be generated with the four lines using an external 4- to 16bit decoder. The Chip Select Registers define the characteristics of the 16 chip selects according to the following rules: SP_CSR0 defines peripheral chip select signals 0 to 3. SP_CSR1 defines peripheral chip select signals 4 to 7. SP_CSR2 defines peripheral chip select signals 8 to 11. SP_CSR3 defines peripheral chip select signals 12 to 15 (1). Note: 1. The 16th state corresponds to a state in which all chip selects are inactive. This allows a different clock configuration to be defined by each chip select register. • MCK32: Clock Selection (Code Label SP_DIV32) 0 = SPI Master Clock equals MCK 1 = SPI Master Clock equals MCK/32 • LLB: Local Loopback Enable (Code Label SP_LLB) 0 = Local loopback path disabled 1 = Local loopback path enabled LLB controls the local loopback on the data serializer for testing in master mode only. • PCS: Peripheral Chip Select (Code Label SP_PCS) This field is only used if Fixed Peripheral Select is active (PS = 0). If PCSDEC=0: PCS = xxx0 NPCS[3:0] = 1110 PCS = xx01 NPCS[3:0] = 1101 PCS = x011 NPCS[3:0] = 1011 PCS = 0111 NPCS[3:0] = 0111 PCS = 1111 forbidden (no peripheral is selected) (x = don’t care) If PCSDEC=1: NPCS[3:0] output signals = PCS 177 1779B–ATARM–22-Mar-02 • DLYBCS: Delay Between Chip Selects (Code Label SP_DLYBCS) This field defines the delay from NPCS inactive to the activation of another NPCS. The DLYBCS time guarantees nonoverlapping chip selects and solves bus contentions in case of peripherals having long data float times. If DLYBCS is less than or equal to six, six SPI Master Clock periods will be inserted by default. Otherwise, the following equation determines the delay: Delay_ Between_Chip_Selects = DLYBCS • SPI_Master_Clock_period SPI Receive Data Register Register Name: Access Type: Offset: Reset Value: SP_RDR Read-only 0x08 0x0 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – 15 14 13 12 PCS 11 10 9 8 3 2 1 0 RD 7 6 5 4 RD • RD: Receive Data (Code Label SP_RD) Data received by the SPI Interface is stored in this register right-justified. Unused bits read zero. • PCS: Peripheral Chip Select Status In Master Mode only, these bits indicate the value on the NPCS pins at the end of a transfer. Otherwise, these bits read zero. 178 AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A SPI Transmit Data Register Register Name: Access Type: Offset: SP_TDR Write-only 0x0C 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – 15 14 13 12 PCS 11 10 9 8 3 2 1 0 TD 7 6 5 4 TD • TD: Transmit Data (Code Label SP_TD) Data which is to be transmitted by the SPI Interface is stored in this register. Information to be transmitted must be written to the transmit data register in a right-justified format. • PCS: Peripheral Chip Select This field is only used if Variable Peripheral Select is active (PS = 1) and if the SPI is in Master Mode. If PCSDEC = 0: PCS = xxx0 NPCS[3:0] = 1110 PCS = xx01 NPCS[3:0] = 1101 PCS = x011 NPCS[3:0] = 1011 PCS = 0111 NPCS[3:0] = 0111 PCS = 1111 forbidden (no peripheral is selected) (x = don’t care) If PCSDEC = 1: NPCS[3:0] output signals = PCS 179 1779B–ATARM–22-Mar-02 SPI Status Register Register Name: Access Type: Offset: Reset Value: SP_SR Read-only 0x10 0x0 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – SPIENS 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – SPENDTX SPENDRX OVRES MODF TDRE RDRF • RDRF: Receive Data Register Full (Code Label SP_RDRF) 0 = No data has been received since the last read of SP_RDR 1= Data has been received and the received data has been transferred from the serializer to SP_RDR since the last read of SP_RDR. • TDRE: Transmit Data Register Empty (Code Label SP_TDRE) 0 = Data has been written to SP_TDR and not yet transferred to the serializer. 1 = The last data written in the Transmit Data Register has been transferred in the serializer. TDRE equals zero when the SPI is disabled or at reset. The SPI enable command sets this bit to one. • MODF: Mode Fault Error (Code Label SP_MODF) 0 = No Mode Fault has been detected since the last read of SP_SR. 1 = A Mode Fault occurred since the last read of the SP_SR. • OVRES: Overrun Error Status (Code Label SP_OVRES) 0 = No overrun has been detected since the last read of SP_SR. 1 = An overrun has occurred since the last read of SP_SR. An overrun occurs when SP_RDR is loaded at least twice from the serializer since the last read of the SP_RDR. • SPENDRX: End of Receiver Transfer (Code Label SP_SPENDRX) 0 = The End of Transfer signal from the Peripheral Data Controller channel dedicated to the receiver is inactive. 1 = The End of Transfer signal from the Peripheral Data Controller channel dedicated to the receiver is active. • SPENDTX: End of Transmitter Transfer (Code Label SP_SPENDTX) 0 = The End of Transfer signal from the Peripheral Data Controller channel dedicated to the transmitter is inactive. 1 = The End of Transfer signal from the Peripheral Data Controller channel dedicated to the transmitter is active. • SPIENS: SPI Enable Status (Code Label SP_SPIENS) 0 = SPI is disabled. 1 = SPI is enabled. 180 AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A SPI Interrupt Enable Register Register Name: Access Type: Offset: SP_IER Write-only 0x14 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – SPENDTX SPENDRX OVRES MODF TDRE RDRF • RDRF: Receive Data Register Full Interrupt Enable (Code Label SP_RDRF) 0 = No effect. 1 = Enables the Receiver Data Register Full Interrupt. • TDRE: SPI Transmit Data Register Empty Interrupt Enable (Code Label SP_TDRE) 0 = No effect. 1 = Enables the Transmit Data Register Empty Interrupt. • MODF: Mode Fault Error Interrupt Enable (Code Label SP_MODF) 0 = No effect. 1 = Enables the Mode Fault Interrupt. • OVRES: Overrun Error Interrupt Enable (Code Label SP_OVRES) 0 = No effect. 1 = Enables the Overrun Error Interrupt. • SPENDRX: End of Receiver Transfer Interrupt Enable (Code Label SP_SPENDRX) 0 = No effect. 1 = Enables the End of Receiver Transfer Interrupt. • SPENDTX: End of Transmitter Transfer Interrupt Enable (Code Label SP_SPENDTX) 0 = No effect. 1 = Enables the End of Transmitter Transfer Interrupt. 181 1779B–ATARM–22-Mar-02 SPI Interrupt Disable Register Register Name: Access Type: Offset: SP_IDR Write-only 0x18 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – SPENDTX SPENDRX OVRES MODF TDRE RDRF • RDRF: Receive Data Register Full Interrupt Disable (Code Label SP_RDRF) 0 = No effect. 1 = Disables the Receiver Data Register Full Interrupt. • TDRE: Transmit Data Register Empty Interrupt Disable (Code Label SP_TDRE) 0 = No effect. 1 = Disables the Transmit Data Register Empty Interrupt. • MODF: Mode Fault Interrupt Disable (Code Label SP_MODF) 0 = No effect. 1 = Disables the Mode Fault Interrupt. • OVRES: Overrun Error Interrupt Disable (Code Label SP_OVRES) 0 = No effect. 1 = Disables the Overrun Error Interrupt. • SPENDRX: End of Receiver Transfer Interrupt Disable (Code Label SP_SPENDRX) 0 = No effect. 1 = Disables the End of Receiver Transfer Interrupt. • SPENDTX: End of Transmitter Transfer Interrupt Disable (Code Label SP_SPENDTX) 0 = No effect. 1 = Disables the End of Transmitter Transfer Interrupt. 182 AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A SPI Interrupt Mask Register Register Name: Access Type: Offset: Reset Value: SP_IMR Read-only 0x1C 0x0 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 – – – – – – – – 7 6 5 4 3 2 1 0 – – SPENDTX SPENDRX OVRES MODF TDRE RDRF • RDRF: Receive Data Register Full Interrupt Mask (Code Label SP_RDRF) 0 = Receive Data Register Full Interrupt is disabled. 1 = Receive Data Register Full Interrupt is enabled. • TDRE: Transmit Data Register Empty Interrupt Mask (Code Label SP_TDRE) 0 = Transmit Data Register Empty Interrupt is disabled. 1 = Transmit Data Register Empty Interrupt is enabled. • MODF: Mode Fault Interrupt Mask (Code Label SP_MODF) 0 = Mode Fault Interrupt is disabled. 1 = Mode Fault Interrupt is enabled. • OVRES: Overrun Error Interrupt Mask (Code Label SP_OVRES) 0 = Overrun Error Interrupt is disabled. 1 = Overrun Error Interrupt is enabled. • SPENDRX: End of Receiver Transfer Interrupt Mask (Code Label SP_SPENDRX) 0 = End of Receiver Transfer Interrupt is disabled. 1 = End of Receiver Transfer Interrupt is enabled. • SPENDTX: End of Transmitter Transfer Interrupt Mask (Code Label SP_SPENDTX) 0 = End of Transmitter Transfer Interrupt is disabled. 1 = End of Transmitter Transfer Interrupt is enabled. 183 1779B–ATARM–22-Mar-02 SPI Receive Pointer Register Name: Access Type: Offset: Reset Value: 31 SP_RPR Read/Write 0x20 0x0 30 29 28 27 26 25 24 19 18 17 16 11 10 9 8 3 2 1 0 RXPTR 23 22 21 20 RXPTR 15 14 13 12 RXPTR 7 6 5 4 RXPTR • RXPTR: Receive Pointer RXPTR must be loaded with the address of the receive buffer. SPI Receive Counter Register Name: Access Type: Offset: Reset Value: SP_RCR Read/Write 0x24 0x0 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 3 2 1 0 RXCTR 7 6 5 4 RXCTR • RXCTR: Receive Counter RXCTR must be loaded with the size of the receive buffer. 0: Stop Peripheral Data Transfer dedicated to the receiver. 1-65535: Start Peripheral Data transfer if RDRF is active. 184 AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A SPI Transmit Pointer Register Name: Access Type: Offset: Reset Value: 31 SP_TPR Read/Write 0x28 0x0 30 29 28 27 26 25 24 19 18 17 16 11 10 9 8 3 2 1 0 TXPTR 23 22 21 20 TXPTR 15 14 13 12 TXPTR 7 6 5 4 TXPTR • TXPTR: Transmit Pointer TXPTR must be loaded with the address of the transmit buffer. SPI Transmit Counter Register Name: Access Type: Offset: Reset Value: SP_TCR Read/Write 0x2C 0x0 31 30 29 28 27 26 25 24 – – – – – – – – 23 22 21 20 19 18 17 16 – – – – – – – – 15 14 13 12 11 10 9 8 3 2 1 0 TXCTR 7 6 5 4 TXCTR • TXCTR: Transmit Counter TXCTR must be loaded with the size of the transmit buffer. 0: Stop Peripheral Data Transfer dedicated to the transmitter. 1-65535: Start Peripheral Data transfer if TDRE is active. 185 1779B–ATARM–22-Mar-02 SPI Chip Select Register Register Name: Access Type: Reset Value: 31 SP_CSR0..SP_CSR3 Read/Write 0x0 30 29 28 27 26 25 24 19 18 17 16 11 10 9 8 DLYBCT 23 22 21 20 DLYBS 15 14 13 12 SCBR 7 6 5 4 BITS 3 2 1 0 – – NCPHA CPOL • CPOL: Clock Polarity (Code Label SP_CPOL) 0 = The inactive state value of SPCK is logic level zero. 1 = The inactive state value of SPCK is logic level one. CPOL is used to determine the inactive state value of the serial clock (SPCK). It is used with NCPHA to produce a desired clock/data relationship between master and slave devices. • NCPHA: Clock Phase (Code Label SP_NCPHA) 0 = Data is changed on the leading edge of SPCK and captured on the following edge of SPCK. 1 = Data is captured on the leading edge of SPCK and changed on the following edge of SPCK. NCPHA determines which edge of SPCK causes data to change and which edge causes data to be captured. NCPHA is used with CPOL to produce a desired clock/data relationship between master and slave devices. • BITS: Bits Per Transfer The BITS field determines the number of data bits transferred. Reserved values should not be used. 186 BITS[3:0] Bits Per Transfer Code Label: SP_BITS 0000 8 SP_BITS_8 0001 9 SP_BITS_9 0010 10 SP_BITS_10 0011 11 SP_BITS_11 0100 12 SP_BITS_12 0101 13 SP_BITS_13 0110 14 SP_BITS_14 0111 15 SP_BITS_15 1000 16 SP_BITS_16 1001 Reserved – 1010 Reserved – 1011 Reserved – 1100 Reserved – 1101 Reserved – 1110 Reserved – 1111 Reserved – AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A • SCBR: Serial Clock Baud Rate (Code Label SP_SCBR) In Master Mode, the SPI Interface uses a modulus counter to derive the SPCK baud rate from the SPI Master Clock (selected between MCK and MCK/32). The baud rate is selected by writing a value from 2 to 255 in the field SCBR. The following equation determines the SPCK baud rate: SPI_Master_Clock_frequency SPCK_Baud_Rate = 2 x SCBR Giving SCBR a value of zero or one disables the baud rate generator. SPCK is disabled and assumes its inactive state value. No serial transfers may occur. At reset, baud rate is disabled. • DLYBS: Delay Before SPCK (Code Label SP_DLYBS) This field defines the delay from NPCS valid to the first valid SPCK transition. When DLYBS equals zero, the NPCS valid to SPCK transition is 1/2 the SPCK clock period. Otherwise, the following equation determines the delay: NPCS_to_SPCK_Delay = DLYBS • SPI_Master_Clock_period • DLYBCT: Delay Between Consecutive Transfers (Code Label SP_DLYBCT) This field defines the delay between two consecutive transfers with the same peripheral without removing the chip select. The delay is always inserted after each transfer and before removing the chip select if needed. When DLYBCT equals zero, a delay of four SPI Master Clock periods are inserted. Otherwise, the following equation determines the delay: Delay_After_Transfer = 32 • DLYBCT • SPI_Master_Clock_period 187 1779B–ATARM–22-Mar-02 JTAG Boundary-scan Register The Boundary-scan Register (BSR) contains 237 bits which correspond to active pins and associated control signals. Each AT91M42800A input pin has a corresponding bit in the Boundary-scan Register for observability. Each AT91M42800A output pin has a corresponding 2-bit register in the BSR. The OUTPUT bit contains data that can be forced on the pad. The CTRL bit can put the pad into high impedance. Each AT91M42800A in/out pin corresponds to a 3-bit register in the BSR. The OUTPUT bit contains data that can be forced on the pad. The INPUT bit is for the observability of data applied to the pad. The CTRL bit selects the direction of the pad. Table 22. Boundary-scan Register Bit Number Associated BSR Cells Bit Number OUTPUT 210 INPUT 209 235 CTRL 208 CTRL 234 OUTPUT 207 OUTPUT INPUT 206 232 CTRL 205 231 OUTPUT 204 Pin Name Pin Type 237 236 233 230 PA25/MCKO PA24/NPCSB3 PA23/NPCSB2 IN/OUT IN/OUT IN/OUT Pin Type Associated BSR Cells OUTPUT PA16/NPCSA2 PA15/NPCSA1 IN/OUT IN/OUT INPUT INPUT CTRL OUTPUT PA14/NPCSA0/ NSSA INPUT 203 229 CTRL 202 CTRL 228 OUTPUT 201 OUTPUT INPUT 200 CTRL 199 CTRL OUTPUT 198 OUTPUT INPUT 197 223 CTRL 196 CTRL 222 OUTPUT 195 OUTPUT INPUT 194 220 CTRL 193 CTRL 219 OUTPUT 192 OUTPUT INPUT 191 217 CTRL 190 CTRL 216 OUTPUT 189 OUTPUT INPUT 188 CTRL 187 227 PA22/NPCSB1 IN/OUT 226 225 224 221 218 215 PA21/NPCSB0/ NSSB PA20/MOSIB PA19/MISOB PA18/SPCKB IN/OUT IN/OUT IN/OUT IN/OUT 214 188 Pin Name PA13/MOSIA PA12/MISOA PA11/SPCKA PA10/RXD1 PA9/TXD1/NTRI IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT INPUT INPUT INPUT INPUT INPUT INPUT CTRL AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A Table 22. Boundary-scan Register (Continued) Bit Number Associated BSR Cells Bit Number OUTPUT 186 INPUT 185 211 CTRL 184 CTRL 183 OUTPUT 150 OUTPUT INPUT 149 181 CTRL 148 CTRL 180 OUTPUT 147 OUTPUT INPUT 146 178 CTRL 145 CTRL 177 OUTPUT 144 OUTPUT INPUT 143 175 CTRL 142 CTRL 174 OUTPUT 141 OUTPUT INPUT 140 172 CTRL 139 CTRL 171 OUTPUT 138 OUTPUT INPUT 137 169 CTRL 136 CTRL 168 OUTPUT 135 OUTPUT INPUT 134 166 CTRL 133 CTRL 165 OUTPUT 132 OUTPUT INPUT 131 163 CTRL 130 CTRL 162 OUTPUT 129 OUTPUT INPUT 128 160 CTRL 127 CTRL 159 OUTPUT 126 OUTPUT INPUT 125 157 CTRL 124 CTRL 156 OUTPUT 123 OUTPUT INPUT 122 CTRL 121 Pin Name Pin Type 213 212 182 179 176 173 170 167 164 161 158 155 PA17/NPCSA3 PA7/RXD0 PA6/TXD0 PA5/SCK0 PA4/FIQ PA3/IRQ3 PA2/IRQ2 PA1/IRQ1 PA0/IRQ0 PB23/TIOB5 PB22/TIOA5 154 IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT Pin Name Pin Type Associated BSR Cells OUTPUT PA8/SCK1 PB20/TIOB4 PB19/TIOA4 PB18/TCLK4 PB17/TIOB3 PB16/TIOA3 PB15/TCLK3 PB14/TIOB2 PB13/TIOA2 PB12/TCLK2 PB11/TIOB1 IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT IN/OUT INPUT INPUT INPUT INPUT INPUT INPUT INPUT INPUT INPUT INPUT INPUT CTRL 189 1779B–ATARM–22-Mar-02 Table 22. Boundary-scan Register (Continued) Bit Number Associated BSR Cells Bit Number OUTPUT 120 INPUT 119 151 CTRL 118 117 OUTPUT 82 INPUT 81 Pin Name Pin Type 153 152 116 PB21/TCLK5 PB9/TCLK1 IN/OUT IN/OUT 115 CTRL 80 114 OUTPUT 79 INPUT 78 113 PB8/TIOB0 IN/OUT 112 CTRL 77 111 OUTPUT 76 Pin Name PB7/TIOA0 IN/OUT 109 INPUT 75 CTRL 74 PB10/TIOA1 107 IN/OUT PB6/TCLK0 OUTPUT 73 INPUT 72 D5 IN/OUT D4 IN/OUT 105 D15 103 INPUT D[7:4] IN/OUT D3 IN/OUT 101 OUTPUT INPUT OUTPUT 99 INPUT OUTPUT D[15:12] IN/OUT D11 IN/OUT 96 95 94 D10 INPUT OUTPUT 92 90 D[11:8] IN/OUT D7 IN/OUT 87 86 190 71 INPUT OUTPUT 70 INPUT 69 OUTPUT 68 INPUT 67 CTRL OUTPUT 66 OUTPUT INPUT 65 OUTPUT 64 CTRL INPUT 63 OUTPUT CTRL 62 OUTPUT 61 CTRL INPUT 60 OUTPUT OUTPUT 59 INPUT 58 OUTPUT 57 A19 OUTPUT OUTPUT INPUT 56 A18 OUTPUT OUTPUT OUTPUT 55 A17 OUTPUT OUTPUT INPUT 54 A16 OUTPUT OUTPUT CTRL 53 A[19:16] OUTPUT CTRL OUTPUT 52 A15 OUTPUT OUTPUT INPUT 51 A14 OUTPUT OUTPUT D[3:0] IN/OUT CTRL OUTPUT PB5/A23/CS4 IN/OUT INPUT PB4/A22/CS5 IN/OUT INPUT PB3/A21/CS6 PB2/A20/CS7 IN/OUT IN/OUT INPUT INPUT CTRL IN/OUT 89 88 CTRL IN/OUT 91 D8 IN/OUT IN/OUT 93 D9 IN/OUT IN/OUT 98 97 IN/OUT IN/OUT 100 D12 CTRL IN/OUT 102 D13 INPUT IN/OUT 104 D14 INPUT OUTPUT D0 106 IN/OUT CTRL D1 108 Associated BSR Cells OUTPUT D2 110 Pin Type AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A Table 22. Boundary-scan Register (Continued) Bit Number Pin Name Pin Type 85 D6 Associated BSR Cells Bit Number Pin Name Pin Type Associated BSR Cells OUTPUT 50 A13 OUTPUT OUTPUT INPUT 49 A12 OUTPUT OUTPUT A[15:12] OUTPUT CTRL IN/OUT 84 83 D5 IN/OUT OUTPUT 48 47 A11 OUTPUT OUTPUT 21 OUTPUT NWE/NWR0 46 A10 OUTPUT OUTPUT 20 45 A9 OUTPUT OUTPUT 19 INPUT OUTPUT NOE/NRD 44 A8 OUTPUT OUTPUT 43 A[11:8] OUTPUT CTRL 42 A7 OUTPUT OUTPUT 41 A6 OUTPUT OUTPUT 40 A5 OUTPUT OUTPUT 39 A4 OUTPUT 38 A[7:4] 37 IN/OUT IN/OUT 18 INPUT 17 NOE/NRD NEW/NWR0 NUB/NWR1 NCS1 IN/OUT CTRL OUTPUT 16 NWAIT INPUT INPUT OUTPUT CTRL 15 A3 OUTPUT OUTPUT 14 36 A2 OUTPUT OUTPUT 13 CTRL 35 A1 OUTPUT OUTPUT 12 OUTPUT 34 NLB/A0 OUTPUT OUTPUT 11 33 A[3:0] OUTPUT CTRL 10 OUTPUT 9 INPUT 8 30 CTRL 7 29 OUTPUT 6 INPUT 5 CTRL 5 32 31 28 PB1/NCS3 PB0/NCS2 IN/OUT IN/OUT 27 26 NCS1 OUTPUT NCS0 IN/OUT 25 24 23 NUB/NWR1 22 OUTPUT PA29/PME PA28 IN/OUT IN/OUT INPUT INPUT CTRL NRST INPUT INPUT OUTPUT PA27/BMS IN/OUT INPUT CTRL NWDOVF OUTPUT NWDOVF OUTPUT OUTPUT OUTPUT OUTPUT 4 CTRL OUTPUT 3 OUTPUT CTRL 2 OUTPUT 1 PA26 IN/OUT INPUT CTRL IN/OUT INPUT 191 1779B–ATARM–22-Mar-02 Document Details Title AT91M42800A Datasheet Literature Number 1779 Revision History Version A Publication Date: Oct-01 Version B Publication Date: 22-Mar-02 Revisions Since Previous Version Page: 4 Change in Table 2 Page: 5 Change in Table 3 Page: 10 Change in Table 4 Page: 11 Change in section Power Supply Change in section Clock Generator Page: 13 Added section Protection Mode Change in section Internal Memories Deleted section Protect Mode 192 AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A Table of Contents Features................................................................................................. 1 Description ............................................................................................ 1 Pin Configuration.................................................................................. 2 Pin Description ..................................................................................... 5 Block Diagram....................................................................................... 7 Architectural Overview......................................................................... 8 Memories .............................................................................................................. 8 Peripherals............................................................................................................ 8 Associated Documentation ............................................................... 10 Product Overview ............................................................................... 11 Power Supply...................................................................................................... Input/Output Considerations ............................................................................... Operating Modes ................................................................................................ Clock Generator.................................................................................................. Reset .................................................................................................................. Emulation Functions ........................................................................................... Memory Controller .............................................................................................. External Bus Interface ........................................................................................ 11 11 11 11 12 12 13 14 Peripherals .......................................................................................... 15 System Peripherals............................................................................................. 16 User Peripherals ................................................................................................. 17 Memory Map........................................................................................ 18 Peripheral Memory Map ..................................................................... 20 EBI: External Bus Interface................................................................ 21 External Memory Mapping.................................................................................. Abort Status ........................................................................................................ EBI Behavior During Internal Accesses.............................................................. Pin Description.................................................................................................... Chip Select Lines................................................................................................ Data Bus Width................................................................................................... Byte Write or Byte Select Access ....................................................................... Boot on NCS0..................................................................................................... Read Protocols ................................................................................................... Write Data Hold Time ......................................................................................... Wait States ......................................................................................................... 21 22 22 23 24 25 26 28 29 31 32 i 1779B–ATARM–22-Mar-02 Memory Access Waveforms ............................................................................... EBI User Interface .............................................................................................. EBI Chip Select Register .................................................................................... EBI Remap Control Register .............................................................................. EBI Memory Control Register ............................................................................. Abort Status Register.......................................................................................... Abort Address Status Register ........................................................................... 36 48 49 51 51 53 54 PMC: Power Management Controller................................................ 55 Oscillator and Slow Clock ................................................................................... Master Clock....................................................................................................... Master Clock Output Controller .......................................................................... ARM Processor Clock Controller ........................................................................ Peripheral Clock Controller ................................................................................. PMC User Interface ............................................................................................ PMC System Clock Enable Register .................................................................. PMC System Clock Disable Register ................................................................. PMC System Clock Status Register ................................................................... PMC Peripheral Clock Enable Register .............................................................. PMC Peripheral Clock Disable Register ............................................................. PMC Peripheral Clock Status Register............................................................... PMC Clock Generator Mode Register ................................................................ PMC Status Register .......................................................................................... PMC Interrupt Enable Register........................................................................... PMC Interrupt Disable Register .......................................................................... PMC Interrupt Mask Register ............................................................................. 56 56 59 59 60 61 62 62 63 63 64 64 65 66 67 67 68 ST: System Timer ............................................................................... 69 PIT: Period Interval Timer ................................................................................... WDT: Watchdog Timer ....................................................................................... RTT: Real-time Timer ......................................................................................... System Timer User Interface .............................................................................. System Timer Control Register........................................................................... System Timer Period Interval Mode Register ..................................................... System Timer Watchdog Mode Register ............................................................ System Timer Real-time Mode Register............................................................. System Timer Status Register ............................................................................ System Timer Interrupt Enable Register............................................................. System Timer Interrupt Disable Register ............................................................ System Timer Interrupt Mask Register ............................................................... System Timer Real-time Alarm Register ............................................................ System Timer Current Real-time Register.......................................................... 69 69 70 72 73 74 74 75 75 76 77 78 78 79 AIC: Advanced Interrupt Controller .................................................. 80 Hardware Interrupt Vectoring.............................................................................. 82 Priority Controller ................................................................................................ 82 ii AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A Interrupt Handling ............................................................................................... Interrupt Masking ................................................................................................ Interrupt Clearing and Setting............................................................................. Fast Interrupt Request ........................................................................................ Software Interrupt ............................................................................................... Spurious Interrupt ............................................................................................... Protect Mode ...................................................................................................... AIC User Interface .............................................................................................. AIC Source Mode Register ................................................................................. AIC Source Vector Register................................................................................ AIC Interrupt Vector Register.............................................................................. AIC FIQ Vector Register ............................................................................................. AIC Interrupt Status Register .............................................................................. AIC Interrupt Pending Register ........................................................................... AIC Interrupt Mask Register ............................................................................... AIC Core Interrupt Status Register ..................................................................... AIC Interrupt Enable Command Register ........................................................... AIC Interrupt Disable Command Register .......................................................... AIC Interrupt Clear Command Register .............................................................. AIC Interrupt Set Command Register ................................................................. AIC End of Interrupt Command Register ............................................................ AIC Spurious Vector Register............................................................................. Standard Interrupt Sequence.............................................................................. Fast Interrupt Sequence ..................................................................................... 82 82 83 83 83 83 84 85 86 87 88 88 89 90 90 91 91 92 93 93 94 94 95 97 PIO: Parallel I/O Controller................................................................. 98 PIO Connection Tables .................................................................................... PIO Enable Register ......................................................................................... PIO Disable Register ........................................................................................ PIO Status Register .......................................................................................... PIO Output Enable Register ............................................................................. PIO Output Disable Register ............................................................................ PIO Output Status Register .............................................................................. PIO Input Filter Enable Register ....................................................................... PIO Input Filter Disable Register ...................................................................... PIO Input Filter Status Register ........................................................................ PIO Set Output Data Register .......................................................................... PIO Clear Output Data Register ....................................................................... PIO Output Data Status Register...................................................................... PIO Pin Data Status Register ........................................................................... PIO Interrupt Enable Register........................................................................... PIO Interrupt Disable Register .......................................................................... PIO Interrupt Mask Register ............................................................................. PIO Interrupt Status Register............................................................................ PIO Multi-drive Enable Register ....................................................................... PIO Multi-drive Disable Register....................................................................... 101 104 104 105 106 106 107 108 108 109 110 110 111 111 112 112 113 113 114 114 iii 1779B–ATARM–22-Mar-02 PIO Multi-drive Status Register ........................................................................ 115 SF: Special Function Registers....................................................... 116 Chip Identification ............................................................................................. Chip ID Register ............................................................................................... Chip ID Extension Register............................................................................... Reset Status Register....................................................................................... SF Protect Mode Register ................................................................................ 116 117 118 119 119 USART: Universal Synchronous/ Asynchronous Receiver/Transmitter.............................................. 120 Pin Description.................................................................................................. Baud Rate Generator........................................................................................ Receiver............................................................................................................ Transmitter........................................................................................................ Multi-drop Mode................................................................................................ Break ................................................................................................................ Peripheral Data Controller ................................................................................ Interrupt Generation.......................................................................................... Channel Modes................................................................................................. USART User Interface ...................................................................................... USART Control Register................................................................................... USART Mode Register ..................................................................................... USART Interrupt Enable Register..................................................................... USART Interrupt Disable Register.................................................................... USART Interrupt Mask Register ....................................................................... USART Channel Status Register...................................................................... USART Receiver Holding Register ................................................................... USART Transmitter Holding Register............................................................... USART Baud Rate Generator Register ............................................................ USART Receiver Time-out Register ................................................................. USART Transmitter Time-guard Register......................................................... USART Receive Pointer Register ..................................................................... USART Receive Counter Register ................................................................... USART Transmit Pointer Register.................................................................... USART Transmit Counter Register .................................................................. 121 122 123 125 125 125 127 127 127 129 130 131 133 134 135 136 137 138 138 139 139 140 140 141 141 TC: Timer/Counter ............................................................................ 142 Signal Name Description(1, 2) ......................................................................... Timer/Counter Description................................................................................ Capture Operating Mode .................................................................................. Waveform Operating Mode............................................................................... TC User Interface ............................................................................................. TC Block Control Register ................................................................................ TC Block Mode Register ................................................................................... TC Channel Control Register............................................................................ iv 143 144 146 149 152 153 154 155 AT91M42800A 1779B–ATARM–22-Mar-02 AT91M42800A TC TC TC TC TC TC TC TC TC TC Channel Mode Register: Capture Mode ..................................................... Channel Mode Register: Waveform Mode .................................................. Counter Value Register............................................................................... Register A ................................................................................................... Register B ................................................................................................... Register C ................................................................................................... Status Register ........................................................................................... Interrupt Enable Register ............................................................................ Interrupt Disable Register ........................................................................... Interrupt Mask Register............................................................................... 156 158 161 161 162 162 163 164 165 166 SPI: Serial Peripheral Interface ....................................................... 167 Pin Description.................................................................................................. Master Mode..................................................................................................... Slave Mode....................................................................................................... Data Transfer.................................................................................................... Clock Generation .............................................................................................. Peripheral Data Controller ................................................................................ SPI Programmer’s Model.................................................................................. SPI Control Register ......................................................................................... SPI Mode Register............................................................................................ SPI Receive Data Register ............................................................................... SPI Transmit Data Register .............................................................................. SPI Status Register .......................................................................................... SPI Interrupt Enable Register ........................................................................... SPI Interrupt Disable Register .......................................................................... SPI Interrupt Mask Register.............................................................................. SPI Receive Pointer Register ........................................................................... SPI Receive Counter Register .......................................................................... SPI Transmit Pointer Register .......................................................................... SPI Transmit Counter Register......................................................................... SPI Chip Select Register .................................................................................. 167 168 172 173 174 174 175 176 177 178 179 180 181 182 183 184 184 185 185 186 JTAG Boundary-scan Register........................................................ 188 Document Details ............................................................................. 192 Revision History................................................................................................ 192 Table of Contents .................................................................................. i v 1779B–ATARM–22-Mar-02 Atmel Headquarters Atmel Operations Corporate Headquarters Memory 2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 441-0311 FAX 1(408) 487-2600 Europe Atmel SarL Route des Arsenaux 41 Casa Postale 80 CH-1705 Fribourg Switzerland TEL (41) 26-426-5555 FAX (41) 26-426-5500 Asia Atmel Asia, Ltd. Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimhatsui East Kowloon Hong Kong TEL (852) 2721-9778 FAX (852) 2722-1369 Japan Atmel Japan K.K. 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan TEL (81) 3-3523-3551 FAX (81) 3-3523-7581 Atmel Corporate 2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 436-4270 FAX 1(408) 436-4314 Microcontrollers Atmel Corporate 2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 436-4270 FAX 1(408) 436-4314 Atmel Nantes La Chantrerie BP 70602 44306 Nantes Cedex 3, France TEL (33) 2-40-18-18-18 FAX (33) 2-40-18-19-60 ASIC/ASSP/Smart Cards Atmel Rousset Zone Industrielle 13106 Rousset Cedex, France TEL (33) 4-42-53-60-00 FAX (33) 4-42-53-60-01 RF/Automotive Atmel Heilbronn Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany TEL (49) 71-31-67-0 FAX (49) 71-31-67-2340 Atmel Colorado Springs 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL 1(719) 576-3300 FAX 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Atmel Grenoble Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France TEL (33) 4-76-58-30-00 FAX (33) 4-76-58-34-80 Atmel Colorado Springs 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL 1(719) 576-3300 FAX 1(719) 540-1759 Atmel Smart Card ICs Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland TEL (44) 1355-803-000 FAX (44) 1355-242-743 e-mail [email protected] Web Site http://www.atmel.com © Atmel Corporation 2002. Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life support devices or systems. ATMEL ® is the registered trademark of Atmel. ARM ®, Thumb ® and ARM Powered ® are the registered trademarks of ARM Ltd. ARM7TDMI™ is the trademark of ARM Ltd. Other terms and product names may be the trademarks of others. Printed on recycled paper. 1779B–ATARM–22-Mar-02 0M