CY7C1354CV25 CY7C1356CV25 9-Mbit (256 K × 36/512 K × 18) Pipelined SRAM with NoBL™ Architecture 9-Mbit (256 K × 36/512 K × 18) Pipelined SRAM with NoBL™ Architecture Features Functional Description ■ Pin-compatible with and functionally equivalent to ZBT™ ■ Supports 250-MHz bus operations with zero wait states ■ Available speed grades are 250, 200, and 166 MHz ■ Internally self-timed output buffer control to eliminate the need to use asynchronous OE ■ Fully registered (inputs and outputs) for pipelined operation ■ Byte write capability ■ Single 2.5 V power supply (VDD) ■ Fast clock-to-output times ❐ 2.8 ns (for 250-MHz device) ■ Clock enable (CEN) pin to suspend operation ■ Synchronous self-timed writes ■ Available in Pb-free 100-pin TQFP package, Pb-free and non Pb-free 119-ball BGA package and 165-ball FBGA package ■ IEEE 1149.1 JTAG-compatible boundary scan ■ Burst capability–linear or interleaved burst order ■ “ZZ” sleep mode option and stop clock option The CY7C1354CV25/CY7C1356CV25[1] are 2.5 V, 256 K × 36/512 K × 18 synchronous pipelined burst SRAMs with No Bus Latency™ (NoBL logic, respectively. They are designed to support unlimited true back-to-back read/write operations with no wait states. The CY7C1354CV25/CY7C1356CV25 are equipped with the advanced (NoBL) logic required to enable consecutive read/write operations with data being transferred on every clock cycle. This feature dramatically improves the throughput of data in systems that require frequent write/read transitions. The CY7C1354CV25/CY7C1356CV25 are pin-compatible with and functionally equivalent to ZBT devices. All synchronous inputs pass through input registers controlled by the rising edge of the clock. All data outputs pass through output registers controlled by the rising edge of the clock. The clock input is qualified by the clock enable (CEN) signal, which when deasserted suspends operation and extends the previous clock cycle. Write operations are controlled by the byte write selects (BWa–BWd for CY7C1354CV25 and BWa–BWb for CY7C1356CV25) and a write enable (WE) input. All writes are conducted with on-chip synchronous self-timed write circuitry. Three synchronous chip enables (CE1, CE2, CE3) and an asynchronous output enable (OE) provide for easy bank selection and output tri-state control. In order to avoid bus contention, the output drivers are synchronously tri-stated during the data portion of a write sequence. For a complete list of related documentation, click here. Note 1. For best-practices recommendations, please refer to the Cypress application note System Design Guidelines on www.cypress.com. Cypress Semiconductor Corporation Document Number: 38-05537 Rev. *P • 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Revised October 19, 2015 CY7C1354CV25 CY7C1356CV25 Logic Block Diagram – CY7C1354CV25 A0, A1, A ADDRESS REGISTER 0 A1 A1' D1 Q1 A0 A0' BURST D0 Q0 LOGIC MODE CLK CEN ADV/LD C C WRITE ADDRESS REGISTER 1 WRITE ADDRESS REGISTER 2 ADV/LD BWa BWb BWc BWd WRITE REGISTRY AND DATA COHERENCY CONTROL LOGIC WRITE DRIVERS MEMORY ARRAY WE S E N S E A M P S O U T P U T R E G I S T E R S E INPUT REGISTER 1 E OE CE1 CE2 CE3 ZZ Document Number: 38-05537 Rev. *P O U T P U T D A T A S T E E R I N G INPUT REGISTER 0 B U F F E R S DQs DQPa DQPb DQPc DQPd E E READ LOGIC SLEEP CONTROL Page 2 of 34 CY7C1354CV25 CY7C1356CV25 Logic Block Diagram – CY7C1356CV25 A0, A1, A ADDRESS REGISTER 0 A1 A1' D1 Q1 A0 BURST A0' D0 Q0 LOGIC MODE CLK CEN ADV/LD C C WRITE ADDRESS REGISTER 1 WRITE ADDRESS REGISTER 2 ADV/LD BWa WRITE REGISTRY AND DATA COHERENCY CONTROL LOGIC WRITE DRIVERS MEMORY ARRAY BWb WE S E N S E A M P S O U T P U T R E G I S T E R S D A T A S T E E R I N G E INPUT REGISTER 1 E OE CE1 CE2 CE3 ZZ Document Number: 38-05537 Rev. *P O U T P U T B U F F E R S DQs DQPa DQPb E INPUT REGISTER 0 E READ LOGIC Sleep Control Page 3 of 34 CY7C1354CV25 CY7C1356CV25 Contents Selection Guide ................................................................ 5 Pin Configurations ........................................................... 5 Pin Definitions .................................................................. 8 Functional Overview ........................................................ 9 Single Read Accesses ................................................ 9 Burst Read Accesses .................................................. 9 Single Write Accesses ................................................. 9 Burst Write Accesses ................................................ 10 Sleep Mode ............................................................... 10 Interleaved Burst Address Table ............................... 10 Linear Burst Address Table ....................................... 10 ZZ Mode Electrical Characteristics ............................ 10 Truth Table ...................................................................... 11 Partial Truth Table for Read/Write ................................ 12 Partial Truth Table for Read/Write ................................ 12 IEEE 1149.1 Serial Boundary Scan (JTAG) .................. 13 Disabling the JTAG Feature ...................................... 13 Test Access Port (TAP) ............................................. 13 PERFORMING A TAP RESET .................................. 13 TAP REGISTERS ...................................................... 13 TAP Instruction Set ................................................... 14 TAP Controller State Diagram ....................................... 15 TAP Controller Block Diagram ...................................... 16 TAP Timing ...................................................................... 16 TAP AC Switching Characteristics ............................... 17 2.5 V TAP AC Test Conditions ....................................... 17 2.5 V TAP AC Output Load Equivalent ......................... 17 Document Number: 38-05537 Rev. *P TAP DC Electrical Characteristics and Operating Conditions ............................................. 18 Identification Register Definitions ................................ 18 Scan Register Sizes ....................................................... 18 Instruction Codes ........................................................... 18 Boundary Scan Exit Order ............................................. 19 Boundary Scan Exit Order ............................................. 20 Maximum Ratings ........................................................... 21 Operating Range ............................................................. 21 Electrical Characteristics ............................................... 21 Capacitance .................................................................... 22 Thermal Resistance ........................................................ 22 AC Test Loads and Waveforms ..................................... 22 Switching Characteristics .............................................. 23 Switching Waveforms .................................................... 24 Ordering Information ...................................................... 27 Ordering Code Definitions ......................................... 27 Package Diagrams .......................................................... 28 Acronyms ........................................................................ 31 Document Conventions ................................................. 31 Units of Measure ....................................................... 31 Document History Page ................................................. 32 Sales, Solutions, and Legal Information ...................... 34 Worldwide Sales and Design Support ....................... 34 Products .................................................................... 34 PSoC® Solutions ...................................................... 34 Cypress Developer Community ................................. 34 Technical Support ..................................................... 34 Page 4 of 34 CY7C1354CV25 CY7C1356CV25 Selection Guide Description 250 MHz 200 MHz 166 MHz Unit Maximum access time 2.8 3.2 3.5 ns Maximum operating current 250 220 180 mA Maximum CMOS standby current 40 40 40 mA Pin Configurations 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 DQPb DQb DQb VDDQ VSS NC NC NC VDDQ VSS NC NC DQb DQb VSS VDDQ CY7C1356CV25 (512 K × 18) 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 A NC NC VDDQ VSS NC DQPa DQa DQa VSS VDDQ DQa DQa VSS NC VDD ZZ DQa DQa VDDQ VSS DQa DQa NC NC VSS VDDQ NC NC NC A A A A A A A NC(72M) NC(36M) VSS VDD NC(288M) NC(144M) 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 DQb DQb DQb DQb VSS VDDQ DQb DQb DQb DQb NC VSS VDD NC VDD NC VSS ZZ DQb DQa DQa DQb VDDQ VDDQ VSS VSS DQa DQb DQa DQb DQa DQPb NC DQa VSS VSS VDDQ VDDQ NC DQa DQa NC DQPa NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 MODE A A A A A1 A0 Document Number: 38-05537 Rev. *P A A A A A A A NC(72M) NC(36M) VSS DQd DQd VDDQ VSS DQd DQd DQd DQd VSS VDDQ DQd DQd DQPd VSS VDD NC CY7C1354CV25 (256 K × 36) NC(288M) NC(144M) DQc DQc NC VDD 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 VSS DQc DQc DQc DQc VSS VDDQ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 MODE A A A A A1 A0 DQPc DQc DQc VDDQ A A A A CE1 CE2 NC NC BWb BWa CE3 VDD VSS CLK WE CEN OE ADV/LD NC(18M) A A A 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 A A CE1 CE2 BWd BWc BWb BWa CE3 VDD VSS CLK WE CEN OE ADV/LD NC(18M) A Figure 1. 100-pin TQFP (14 × 20 × 1.4 mm) pinout Page 5 of 34 CY7C1354CV25 CY7C1356CV25 Pin Configurations (continued) Figure 2. 119-ball BGA (14 × 22 × 2.4 mm) pinout CY7C1354CV25 (256 K × 36) 1 2 3 4 5 6 7 A VDDQ A A NC/18M A A VDDQ B C D E F G H J K L M N P NC/576M NC/1G DQc CE2 A DQPc A A VSS ADV/LD VDD NC A A VSS CE3 A DQPb NC NC DQb DQc DQc VSS CE1 VSS DQb DQb VDDQ DQc VSS DQb VDDQ DQc BWb DQb DQb DQc VDDQ DQc VDD BWc VSS NC OE A VSS DQc WE VDD VSS NC DQb VDD DQb VDDQ DQd DQd DQd DQd CLK NC VSS BWd BWa DQa DQa DQa DQa VDDQ DQd VSS DQa VDDQ DQd VSS CEN A1 VSS DQd VSS DQa DQa DQd DQPd VSS A0 VSS DQPa DQa R T U NC/144M A MODE VDD NC/288M NC/72M A A NC A A NC NC/36M ZZ VDDQ TMS TDI TCK TDO NC VDDQ VSS CY7C1356CV25 (512 K × 18) A B C D E F G H J K L M N P R T U 1 2 3 4 5 6 7 VDDQ A A NC/18M A A VDDQ NC/576M CE2 A A A CE3 A NC A ADV/LD VDD A NC/1G DQb NC VSS NC VSS DQPa NC CE1 VSS NC DQa OE A VSS DQa VDDQ VSS VSS NC NC DQa VDD DQa NC VDDQ DQa NC DQb VSS VDDQ NC VSS NC DQb VDDQ DQb NC VDD BWb VSS NC WE VDD NC NC DQb VSS CLK VSS NC DQb NC VSS NC DQa NC VDDQ DQb VSS NC VDDQ DQb NC VSS CEN A1 BWa VSS VSS DQa NC NC DQPb VSS A0 VSS NC DQa NC/144M A MODE VDD NC A NC/288M NC/72M A A NC/36M A A ZZ VDDQ TMS TDI TCK TDO NC VDDQ Document Number: 38-05537 Rev. *P Page 6 of 34 CY7C1354CV25 CY7C1356CV25 Pin Configurations (continued) Figure 3. 165-ball FBGA (13 × 15 × 1.4 mm) pinout CY7C1354CV25 (256 K × 36) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G H J K L M N P NC/576M A CE1 BWc BWb CE3 ADV/LD A A NC BWa VSS CLK CEN WE OE NC/18M VSS VSS VSS VSS VSS VDD VDDQ VDDQ A NC DQb DQPb DQb R MODE NC/1G A CE2 DQPc DQc NC DQc VDDQ VDDQ BWd VSS VDD DQc DQc VDDQ VDD VSS VSS VSS VDD VDDQ DQb DQb DQc DQc VDDQ VDD VSS VSS VSS VDD VDDQ DQb DQb DQc NC DQd DQc NC DQd VDDQ NC VDDQ VDD VDD VDD VSS VSS VSS VSS VSS VSS VSS VSS VSS VDD VDD VDD VDDQ VDDQ DQb NC DQa DQb ZZ DQa DQd DQd VDDQ VDD VSS VSS VSS VDD VDDQ DQa DQa DQd DQd VDDQ VDD VSS VSS VSS VDD VDDQ DQa DQa DQd DQPd DQd NC VDDQ VDDQ VDD VSS VSS NC VSS NC VSS NC VDD VSS VDDQ VDDQ DQa NC DQa DQPa A A TDI A1 TDO A A A NC/288M A A TMS A0 TCK A A A A NC/144M NC/72M NC/36M VSS NC NC CY7C1356CV25 (512 K × 18) A B C D E F G H J K L M N P R 1 2 3 4 5 6 7 8 9 10 11 NC/576M A CE1 BWb NC CE3 CEN ADV/LD A A A DQPa DQa NC/1G A CE2 NC BWa CLK NC DQb VDDQ VSS VDDQ VSS VDD VSS VSS VSS WE VSS VSS OE VSS VDD NC/18M NC NC VDDQ A NC NC VDDQ NC NC DQb VDDQ VDD VSS VSS VSS VDD VDDQ NC DQa NC DQb VDDQ VDD VSS VSS VSS VDD VDDQ NC DQa NC NC DQb DQb NC NC VDDQ NC VDDQ VDD VDD VDD VSS VSS VSS VSS VSS VSS VSS VSS VSS VDD VDD VDD VDDQ VDDQ NC NC DQa DQa ZZ NC DQb NC VDDQ VDD VSS VSS VSS VDD VDDQ DQa NC DQb NC VDDQ VDD VSS VSS VSS VDD VDDQ DQa NC DQb DQPb NC NC VDDQ VDDQ VDD VSS VSS NC VSS NC VSS NC VDD VSS VDDQ VDDQ DQa NC NC NC NC/144M NC/72M A A TDI A1 TDO A A A NC/36M A A TMS A0 TCK A A A MODE Document Number: 38-05537 Rev. *P NC NC/288M A Page 7 of 34 CY7C1354CV25 CY7C1356CV25 Pin Definitions Pin Name A0, A1, A I/O Type Pin Description InputAddress inputs used to select one of the address locations. Sampled at the rising edge of the CLK. synchronous BWa, BWb, InputByte write select inputs, active LOW. Qualified with WE to conduct writes to the SRAM. Sampled on BWc, BWd synchronous the rising edge of CLK. BWa controls DQa and DQPa, BWb controls DQb and DQPb, BWc controls DQc and DQPc, BWd controls DQd and DQPd. WE InputWrite enable input, active LOW. Sampled on the rising edge of CLK if CEN is active LOW. This signal synchronous must be asserted LOW to initiate a write sequence. ADV/LD InputAdvance/load input used to advance the on-chip address counter or load a new address. When synchronous HIGH (and CEN is asserted LOW) the internal burst counter is advanced. When LOW, a new address can be loaded into the device for an access. After being deselected, ADV/LD should be driven LOW in order to load a new address. CLK Inputclock Clock input. Used to capture all synchronous inputs to the device. CLK is qualified with CEN. CLK is only recognized if CEN is active LOW. CE1 InputChip enable 1 input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with CE2 synchronous and CE3 to select/deselect the device. CE2 InputChip enable 2 input, active HIGH. Sampled on the rising edge of CLK. Used in conjunction with CE1 synchronous and CE3 to select/deselect the device. CE3 InputChip enable 3 Input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with CE1 synchronous and CE2 to select/deselect the device. OE InputOutput enable, active LOW. Combined with the synchronous logic block inside the device to control asynchronous the direction of the I/O pins. When LOW, the I/O pins are allowed to behave as outputs. When deasserted HIGH, I/O pins are tri-stated, and act as input data pins. OE is masked during the data portion of a write sequence, during the first clock when emerging from a deselected state and when the device has been deselected. CEN InputClock enable input, active LOW. When asserted LOW the clock signal is recognized by the SRAM. synchronous When deasserted HIGH the clock signal is masked. Since deasserting CEN does not deselect the device, CEN can be used to extend the previous cycle when required. DQS I/OBidirectional data I/O lines. As inputs, they feed into an on-chip data register that is triggered by the synchronous rising edge of CLK. As outputs, they deliver the data contained in the memory location specified by addresses during the previous clock rise of the read cycle. The direction of the pins is controlled by OE and the internal control logic. When OE is asserted LOW, the pins can behave as outputs. When HIGH, DQa–DQd are placed in a tri-state condition. The outputs are automatically tri-stated during the data portion of a write sequence, during the first clock when emerging from a deselected state, and when the device is deselected, regardless of the state of OE. DQPX I/OBidirectional data parity I/O lines. Functionally, these signals are identical to DQ[a:d]. During write synchronous sequences, DQPa is controlled by BWa, DQPb is controlled by BWb, DQPc is controlled by BWc, and DQPd is controlled by BWd. MODE Input strap pin Mode input. Selects the burst order of the device. Tied HIGH selects the interleaved burst order. Pulled LOW selects the linear burst order. MODE should not change states during operation. When left floating MODE will default HIGH, to an interleaved burst order. TDO JTAG serial Serial data-out to the JTAG circuit. Delivers data on the negative edge of TCK. output synchronous TDI JTAG serial Serial data-in to the JTAG circuit. Sampled on the rising edge of TCK. input synchronous TMS Test mode This pin controls the test access port state machine. Sampled on the rising edge of TCK. select synchronous Document Number: 38-05537 Rev. *P Page 8 of 34 CY7C1354CV25 CY7C1356CV25 Pin Definitions (continued) Pin Name TCK VDD VDDQ I/O Type JTAG-clock Pin Description Clock input to the JTAG circuitry. Power supply Power supply inputs to the core of the device. I/O power supply Power supply for the I/O circuitry. VSS Ground NC – No connects. This pin is not connected to the die. NC/18M, NC/36M, NC/72M, NC/144M, NC/288M, NC/576M, NC/1G – These pins are not connected. They will be used for expansion to the 18M, 36M, 72M, 144M 288M, 576M, and 1G densities. ZZ Ground for the device. Should be connected to ground of the system. InputZZ “sleep” Input. This active HIGH input places the device in a non-time critical “sleep” condition with asynchronous data integrity preserved. For normal operation, this pin has to be LOW or left floating. ZZ pin has an internal pull-down. Functional Overview The CY7C1354CV25/CY7C1356CV25 are synchronous-pipelined burst NoBL SRAMs designed specifically to eliminate wait states during write/read transitions. All synchronous inputs pass through input registers controlled by the rising edge of the clock. The clock signal is qualified with the clock enable input signal (CEN). If CEN is HIGH, the clock signal is not recognized and all internal states are maintained. All synchronous operations are qualified with CEN. All data outputs pass through output registers controlled by the rising edge of the clock. Maximum access delay from the clock rise (tCO) is 2.8 ns (250-MHz device). Accesses can be initiated by asserting all three chip enables (CE1, CE2, CE3) active at the rising edge of the clock. If clock enable (CEN) is active LOW and ADV/LD is asserted LOW, the address presented to the device will be latched. The access can either be a read or write operation, depending on the status of the write enable (WE). BW[d:a] can be used to conduct byte write operations. Write operations are qualified by the write enable (WE). All writes are simplified with on-chip synchronous self-timed write circuitry. Three synchronous chip enables (CE1, CE2, CE3) and an asynchronous output enable (OE) simplify depth expansion. All operations (reads, writes, and deselects) are pipelined. ADV/LD should be driven LOW once the device has been deselected in order to load a new address for the next operation. Single Read Accesses A read access is initiated when the following conditions are satisfied at clock rise: (1) CEN is asserted LOW, (2) CE1, CE2, and CE3 are all asserted active, (3) the write enable input signal WE is deasserted HIGH, and (4) ADV/LD is asserted LOW. The address presented to the address inputs is latched into the address register and presented to the memory core and control logic. The control logic determines that a read access is in progress and allows the requested data to propagate to the input of the output register. At the rising edge of the next clock the Document Number: 38-05537 Rev. *P requested data is allowed to propagate through the output register and onto the data bus within 2.8 ns (250-MHz device) provided OE is active LOW. After the first clock of the read access the output buffers are controlled by OE and the internal control logic. OE must be driven LOW in order for the device to drive out the requested data. During the second clock, a subsequent operation (read/write/deselect) can be initiated. Deselecting the device is also pipelined. Therefore, when the SRAM is deselected at clock rise by one of the chip enable signals, its output will tri-state following the next clock rise. Burst Read Accesses The CY7C1354CV25/CY7C1356CV25 have an on-chip burst counter that allows the user the ability to supply a single address and conduct up to four reads without reasserting the address inputs. ADV/LD must be driven LOW in order to load a new address into the SRAM, as described in Single Read Accesses. The sequence of the burst counter is determined by the MODE input signal. A LOW input on MODE selects a linear burst mode, a HIGH selects an interleaved burst sequence. Both burst counters use A0 and A1 in the burst sequence, and will wrap around when incremented sufficiently. A HIGH input on ADV/LD will increment the internal burst counter regardless of the state of chip enables inputs or WE. WE is latched at the beginning of a burst cycle. Therefore, the type of access (read or write) is maintained throughout the burst sequence. Single Write Accesses Write access are initiated when the following conditions are satisfied at clock rise: (1) CEN is asserted LOW, (2) CE1, CE2, and CE3 are all asserted active, and (3) the write signal WE is asserted LOW. The address presented to A0–A16 is loaded into the address register. The write signals are latched into the control logic block. On the subsequent clock rise the data lines are automatically tri-stated regardless of the state of the OE input signal. This allows the external logic to present the data on DQ and DQP (DQa,b,c,d/DQPa,b,c,d for CY7C1354CV25 and DQa,b/DQPa,b for Page 9 of 34 CY7C1354CV25 CY7C1356CV25 CY7C1356CV25). In addition, the address for the subsequent access (read/write/deselect) is latched into the address register (provided the appropriate control signals are asserted). On the next clock rise the data presented to DQ and DQP (DQa,b,c,d/DQPa,b,c,d for CY7C1354CV25 and DQa,b/DQPa,b for CY7C1356CV25) (or a subset for byte write operations, see Write Cycle Description table for details) inputs is latched into the device and the Write is complete. The data written during the write operation is controlled by BW (BWa,b,c,d for CY7C1354CV25 and BWa,b for CY7C1356CV25) signals. The CY7C1354CV25/CY7C1356CV25 provides byte write capability that is described in the Write Cycle Description table. Asserting the write enable input (WE) with the selected byte write select (BW) input will selectively write to only the desired bytes. Bytes not selected during a byte write operation will remain unaltered. A synchronous self-timed write mechanism has been provided to simplify the write operations. Byte write capability has been included in order to greatly simplify read/modify/write sequences, which can be reduced to simple byte write operations. Because the CY7C1354CV25/CY7C1356CV25 are common I/O devices, data should not be driven into the device while the outputs are active. The output enable (OE) can be deasserted HIGH before presenting data to the DQ and DQP (DQa,b,c,d/DQPa,b,c,d for CY7C1354CV25 and DQa,b/DQPa,b for CY7C1356CV25) inputs. Doing so will tri-state the output drivers. As a safety precaution, DQ and DQP (DQa,b,c,d/DQPa,b,c,d for CY7C1354CV25 and DQa,b/DQPa,b for CY7C1356CV25) are automatically tri-stated during the data portion of a write cycle, regardless of the state of OE. Burst Write Accesses The CY7C1354CV25/CY7C1356CV25 has an on-chip burst counter that allows the user the ability to supply a single address and conduct up to four write operations without reasserting the address inputs. ADV/LD must be driven LOW in order to load the initial address, as described in Single Write Accesses. When ADV/LD is driven HIGH on the subsequent clock rise, the chip enables (CE1, CE2, and CE3) and WE inputs are ignored and the burst counter is incremented. The correct BW (BWa,b,c,d for CY7C1354CV25 and BWa,b for CY7C1356CV25) inputs must be driven in each cycle of the burst write in order to write the correct bytes of data. Sleep Mode The ZZ input pin is an asynchronous input. Asserting ZZ places the SRAM in a power conservation “sleep” mode. Two clock cycles are required to enter into or exit from this “sleep” mode. While in this mode, data integrity is guaranteed. Accesses pending when entering the “sleep” mode are not considered valid nor is the completion of the operation guaranteed. The device must be deselected prior to entering the “sleep” mode. CE1, CE2, and CE3, must remain inactive for the duration of tZZREC after the ZZ input returns LOW. Interleaved Burst Address Table (MODE = Floating or VDD) First Address A1, A0 Second Address A1, A0 Third Address A1, A0 Fourth Address A1, A0 00 01 10 11 01 00 11 10 10 11 00 01 11 10 01 00 Linear Burst Address Table (MODE = GND) First Address A1, A0 Second Address A1, A0 Third Address A1, A0 Fourth Address A1, A0 00 01 10 11 01 10 11 00 10 11 00 01 11 00 01 10 ZZ Mode Electrical Characteristics Parameter IDDZZ tZZS tZZREC tZZI tRZZI Description Sleep mode standby current Device operation to ZZ ZZ recovery time ZZ active to sleep current ZZ Inactive to exit sleep current Document Number: 38-05537 Rev. *P Test Conditions ZZ VDD 0.2 V ZZ VDD 0.2 V ZZ 0.2 V This parameter is sampled This parameter is sampled Min – – 2tCYC – 0 Max 50 2tCYC – 2tCYC – Unit mA ns ns ns ns Page 10 of 34 CY7C1354CV25 CY7C1356CV25 Truth Table The truth table for CY7C1354CV25/CY7C1356CV25 follows. [2, 3, 4, 5, 6, 7, 8] Operation Address used CE ZZ ADV/LD WE BWx OE CEN CLK DQ Deselect cycle None H L L X X X L L–H Tri-state Continue deselect cycle None X L H X X X L L–H Tri-state Read cycle (begin burst) External L L L H X L L L–H Data out (Q) Next X L H X X L L L–H Data out (Q) External L L L H X H L L–H Tri-state Next X L H X X H L L–H Tri-state External L L L L L X L L–H Data in (D) Write cycle (continue burst) Next X L H X L X L L–H Data in (D) NOP/write abort (begin burst) None L L L L H X L L–H Tri-state Write abort (continue burst) Next X L H X H X L L–H Tri-state Current X L X X X X H L–H – None X H X X X X X X Tri-state Read cycle (continue burst) NOP/dummy read (begin burst) Dummy read (continue burst) Write cycle (begin burst) Ignore clock edge (stall) Sleep mode Notes 2. X = “Don’t Care”, H = Logic HIGH, L = Logic LOW, CE stands for all chip enables active. BWx = L signifies at least one byte write select is active, BWx = Valid signifies that the desired byte write selects are asserted, see Write Cycle Description table for details. 3. Write is defined by WE and BWX. See Write Cycle Description table for details. 4. When a write cycle is detected, all I/Os are tri-stated, even during byte writes. 5. The DQ and DQP pins are controlled by the current cycle and the OE signal. 6. CEN = H inserts wait states. 7. Device will power-up deselected and the I/Os in a tri-state condition, regardless of OE. 8. OE is asynchronous and is not sampled with the clock rise. It is masked internally during write cycles. During a read cycle DQs and DQPX = tri-state when OE is inactive or when the device is deselected, and DQs = data when OE is active. Document Number: 38-05537 Rev. *P Page 11 of 34 CY7C1354CV25 CY7C1356CV25 Partial Truth Table for Read/Write The partial truth table for Read/Write for CY7C1354CV25 follows. [9, 10, 11, 12] Function (CY7C1354CV25) WE BWd BWc BWb BWa Read H X X X X Write– no bytes written L H H H H Write byte a–(DQa and DQPa) L H H H L Write byte b – (DQb and DQPb) L H H L H Write bytes b, a L H H L L Write byte c –(DQc and DQPc) L H L H H Write bytes c, a L H L H L Write bytes c, b L H L L H Write bytes c, b, a L H L L L Write byte d –(DQd and DQPd) L L H H H Write bytes d, a L L H H L Write bytes d, b L L H L H Write bytes d, b, a L L H L L Write bytes d, c L L L H H Write bytes d, c, a L L L H L Write bytes d, c, b L L L L H Write all bytes L L L L L Partial Truth Table for Read/Write The partial truth table for Read/Write for CY7C1356CV25 follows. [9, 10, 11, 12] Function (CY7C1356CV25) WE BWb BWa Read H x x Write – no bytes written L H H Write byte a (DQa and DQPa) L H L Write byte b – (DQb and DQPb) L L H Write both bytes L L L Notes 9. X = “Don’t Care”, H = Logic HIGH, L = Logic LOW, CE stands for all chip enables active. BWx = L signifies at least one byte write select is active, BWx = valid signifies that the desired byte write selects are asserted, see Write Cycle Description table for details. 10. Write is defined by WE and BWX. See Write Cycle Description table for details. 11. When a write cycle is detected, all I/Os are tri-stated, even during byte writes. 12. Table only lists a partial listing of the byte write combinations. Any combination of BWX is valid. Appropriate write will be done based on which byte write is active. Document Number: 38-05537 Rev. *P Page 12 of 34 CY7C1354CV25 CY7C1356CV25 IEEE 1149.1 Serial Boundary Scan (JTAG) The CY7C1354CV25/CY7C1356CV25 incorporates a serial boundary scan test access port (TAP) in the BGA package only. The TQFP package does not offer this functionality. This part operates in accordance with IEEE Standard 1149.1-1900, but doesn’t have the set of functions required for full 1149.1 compliance. These functions from the IEEE specification are excluded because their inclusion places an added delay in the critical speed path of the SRAM. Note the TAP controller functions in a manner that does not conflict with the operation of other devices using 1149.1 fully compliant TAPs. The TAP operates using JEDEC-standard 2.5 V I/O logic levels. The CY7C1354CV25/CY7C1356CV25 contains a TAP controller, instruction register, boundary scan register, bypass register, and ID register. Disabling the JTAG Feature It is possible to operate the SRAM without using the JTAG feature. To disable the TAP controller, TCK must be tied LOW (VSS) to prevent clocking of the device. TDI and TMS are internally pulled up and may be unconnected. They may alternately be connected to VDD through a pull-up resistor. TDO should be left unconnected. Upon power-up, the device will come up in a reset state which will not interfere with the operation of the device. Test Access Port (TAP) Test Clock (TCK) The test clock is used only with the TAP controller. All inputs are captured on the rising edge of TCK. All outputs are driven from the falling edge of TCK. Test Mode Select (TMS) The TMS input is used to give commands to the TAP controller and is sampled on the rising edge of TCK. It is allowable to leave this ball unconnected if the TAP is not used. The ball is pulled up internally, resulting in a logic HIGH level. Test Data-In (TDI) The TDI ball is used to serially input information into the registers and can be connected to the input of any of the registers. The register between TDI and TDO is chosen by the instruction that is loaded into the TAP instruction register. For information on loading the instruction register, see TAP Controller State Diagram on page 15. TDI is internally pulled up and can be unconnected if the TAP is unused in an application. TDI is connected to the most significant bit (MSB) of any register. Test Data-Out (TDO) The TDO output ball is used to serially clock data-out from the registers. The output is active depending upon the current state of the TAP state machine (see Instruction Codes on page 18). The output changes on the falling edge of TCK. TDO is connected to the least significant bit (LSB) of any register. Document Number: 38-05537 Rev. *P Performing a TAP Reset A RESET is performed by forcing TMS HIGH (VDD) for five rising edges of TCK. This RESET does not affect the operation of the SRAM and may be performed while the SRAM is operating. At power-up, the TAP is reset internally to ensure that TDO comes up in a high Z state. TAP Registers Registers are connected between the TDI and TDO balls and allow data to be scanned into and out of the SRAM test circuitry. Only one register can be selected at a time through the instruction register. Data is serially loaded into the TDI ball on the rising edge of TCK. Data is output on the TDO ball on the falling edge of TCK. Instruction Register Three-bit instructions can be serially loaded into the instruction register. This register is loaded when it is placed between the TDI and TDO balls as shown in the TAP Controller Block Diagram on page 16. Upon power-up, the instruction register is loaded with the IDCODE instruction. It is also loaded with the IDCODE instruction if the controller is placed in a reset state as described in the previous section. When the TAP controller is in the Capture-IR state, the two least significant bits are loaded with a binary “01” pattern to allow for fault isolation of the board-level serial test data path. Bypass Register To save time when serially shifting data through registers, it is sometimes advantageous to skip certain chips. The bypass register is a single-bit register that can be placed between the TDI and TDO balls. This allows data to be shifted through the SRAM with minimal delay. The bypass register is set LOW (VSS) when the BYPASS instruction is executed. Boundary Scan Register The boundary scan register is connected to all the input and bidirectional balls on the SRAM. The boundary scan register is loaded with the contents of the RAM I/O ring when the TAP controller is in the Capture-DR state and is then placed between the TDI and TDO balls when the controller is moved to the Shift-DR state. The EXTEST, SAMPLE/PRELOAD and SAMPLE Z instructions can be used to capture the contents of the I/O ring. The Boundary Scan Exit Order on page 19 and Boundary Scan Exit Order on page 20 show the order in which the bits are connected. Each bit corresponds to one of the bumps on the SRAM package. The MSB of the register is connected to TDI, and the LSB is connected to TDO. Identification (ID) Register The ID register is loaded with a vendor-specific, 32-bit code during the Capture-DR state when the IDCODE command is loaded in the instruction register. The IDCODE is hardwired into the SRAM and can be shifted out when the TAP controller is in the Shift-DR state. The ID register has a vendor code and other information described in the Identification Register Definitions on page 18. Page 13 of 34 CY7C1354CV25 CY7C1356CV25 TAP Instruction Set Overview Eight different instructions are possible with the three bit instruction register. All combinations are listed in the Instruction Codes table. Three of these instructions are listed as RESERVED and should not be used. The other five instructions are described in detail below. Instructions are loaded into the TAP controller during the Shift-IR state when the instruction register is placed between TDI and TDO. During this state, instructions are shifted through the instruction register through the TDI and TDO balls. To execute the instruction once it is shifted in, the TAP controller needs to be moved into the Update-IR state. IDCODE The IDCODE instruction causes a vendor-specific, 32-bit code to be loaded into the instruction register. It also places the instruction register between the TDI and TDO balls and allows the IDCODE to be shifted out of the device when the TAP controller enters the Shift-DR state. The IDCODE instruction is loaded into the instruction register upon power-up or whenever the TAP controller is given a test logic reset state. SAMPLE Z The SAMPLE Z instruction causes the boundary scan register to be connected between the TDI and TDO pins when the TAP controller is in a Shift-DR state. The SAMPLE Z command puts the output bus into a high Z state until the next command is given during the “Update IR” state. SAMPLE/PRELOAD SAMPLE/PRELOAD is a 1149.1 mandatory instruction. When the SAMPLE/PRELOAD instructions are loaded into the instruction register and the TAP controller is in the Capture-DR state, a snapshot of data on the inputs and output pins is captured in the boundary scan register. The user must be aware that the TAP controller clock can only operate at a frequency up to 20 MHz, while the SRAM clock operates more than an order of magnitude faster. Because there is a large difference in the clock frequencies, it is possible that Document Number: 38-05537 Rev. *P during the Capture-DR state, an input or output will undergo a transition. The TAP may then try to capture a signal while in transition (metastable state). This will not harm the device, but there is no guarantee as to the value that will be captured. Repeatable results may not be possible. To guarantee that the boundary scan register will capture the correct value of a signal, the SRAM signal must be stabilized long enough to meet the TAP controller’s capture set-up plus hold times (tCS and tCH). The SRAM clock input might not be captured correctly if there is no way in a design to stop (or slow) the clock during a SAMPLE/PRELOAD instruction. If this is an issue, it is still possible to capture all other signals and simply ignore the value of the CK and CK# captured in the boundary scan register. Once the data is captured, it is possible to shift out the data by putting the TAP into the Shift-DR state. This places the boundary scan register between the TDI and TDO pins. PRELOAD allows an initial data pattern to be placed at the latched parallel outputs of the boundary scan register cells prior to the selection of another boundary scan test operation. The shifting of data for the SAMPLE and PRELOAD phases can occur concurrently when required—that is, while data captured is shifted out, the preloaded data can be shifted in. BYPASS When the BYPASS instruction is loaded in the instruction register and the TAP is placed in a Shift-DR state, the bypass register is placed between the TDI and TDO pins. The advantage of the BYPASS instruction is that it shortens the boundary scan path when multiple devices are connected together on a board. EXTEST The EXTEST instruction enables the preloaded data to be driven out through the system output pins. This instruction also selects the boundary scan register to be connected for serial access between the TDI and TDO in the shift-DR controller state. Reserved These instructions are not implemented but are reserved for future use. Do not use these instructions. Page 14 of 34 CY7C1354CV25 CY7C1356CV25 TAP Controller State Diagram The TAP Controller State Diagram follows. [13] 1 TEST-LOGIC RESET 0 0 RUN-TEST/ IDLE 1 SELECT DR-SCAN 1 SELECT IR-SCAN 0 1 0 1 CAPTURE-DR CAPTURE-IR 0 0 SHIFT-DR 0 SHIFT-IR 1 1 EXIT1-IR 0 1 0 PAUSE-DR 0 PAUSE-IR 1 0 1 EXIT2-DR 0 EXIT2-IR 1 1 UPDATE-DR 1 0 1 EXIT1-DR 0 1 0 UPDATE-IR 1 0 Note 13. The 0/1 next to each state represents the value of TMS at the rising edge of the TCK. Document Number: 38-05537 Rev. *P Page 15 of 34 CY7C1354CV25 CY7C1356CV25 TAP Controller Block Diagram 0 Bypass Register 2 1 0 TDI Selection Circuitry Instruction Register 31 30 29 . . Selection Circuitry . 2 1 0 TDO Identification Register x . . . . . 2 1 0 Boundary Scan Register TCK TMS TAP CONTROLLER TAP Timing 1 2 Test Clock (TCK) 3 tTH tTMSS tTMSH tTDIS tTDIH t TL 4 5 6 tCYC Test Mode Select (TMS) Test Data-In (TDI) tTDOV tTDOX Test Data-Out (TDO) DON’T CARE Document Number: 38-05537 Rev. *P UNDEFINED Page 16 of 34 CY7C1354CV25 CY7C1356CV25 TAP AC Switching Characteristics Over the Operating Range Parameter [14, 15] Description Min Max Unit Clock tTCYC TCK clock cycle time 50 – ns tTF TCK clock frequency – 20 MHz tTH TCK clock HIGH time 20 – ns tTL TCK clock LOW time 20 – ns tTDOV TCK clock LOW to TDO valid – 10 ns tTDOX TCK clock LOW to TDO invalid 0 – ns tTMSS TMS set-up to TCK clock rise 5 – ns tTDIS TDI set-up to TCK clock rise 5 – ns tCS Capture set-up to TCK rise 5 – ns tTMSH TMS hold after TCK clock rise 5 – ns tTDIH TDI hold after clock rise 5 – ns tCH Capture hold after clock rise 5 – ns Output Times Set-up Times Hold Times 2.5 V TAP AC Test Conditions 2.5 V TAP AC Output Load Equivalent 1.25V Input pulse levels ...............................................VSS to 2.5 V Input rise and fall time ....................................................1 ns 50Ω Input timing reference levels ....................................... 1.25 V Output reference levels .............................................. 1.25 V TDO Test load termination supply voltage .................. ........1.25 V Z O= 50Ω 20pF Notes 14. tCS and tCH refer to the set-up and hold time requirements of latching data from the boundary scan register. 15. Test conditions are specified using the load in TAP AC test Conditions. tR/tF = 1 ns. Document Number: 38-05537 Rev. *P Page 17 of 34 CY7C1354CV25 CY7C1356CV25 TAP DC Electrical Characteristics and Operating Conditions (0 °C < TA < +70 °C; VDD = 2.5 V ± 0.125 V unless otherwise noted) Parameter [16] Description Test Conditions Min Max Unit VOH1 Output HIGH voltage IOH = –1.0 mA, VDDQ = 2.5 V 2.0 – V VOH2 Output HIGH voltage IOH = –100 µA, VDDQ = 2.5 V 2.1 – V VOL1 Output LOW voltage IOL = 8.0 mA, VDDQ = 2.5 V – 0.4 V VOL2 Output LOW voltage IOL = 100 µA – 0.2 V VDDQ = 2.5 V VIH Input HIGH voltage VDDQ = 2.5 V 1.7 VDD + 0.3 V VIL Input LOW voltage VDDQ = 2.5 V –0.3 0.7 V IX Input Load current –5 5 µA GND < VIN < VDDQ Identification Register Definitions Instruction Field CY7C1354CV25 Revision number (31:29) CY7C1356CV25 000 000 Cypress device ID (28:12) 01011001000100110 01011001000010110 Cypress JEDEC ID (11:1) 00000110100 00000110100 1 1 ID register presence (0) Description Reserved for version number. Reserved for future use. Allows unique identification of SRAM vendor. Indicate the presence of an ID register. Scan Register Sizes Register Name Instruction Bit Size (× 36) Bit Size (× 18) 3 3 Bypass 1 1 ID 32 32 Boundary scan order (119-ball BGA package) 69 69 Boundary scan order (165-ball FBGA package) 69 69 Instruction Codes Code Description EXTEST Instruction 000 Captures the input/output ring contents. Places the boundary scan register between the TDI and TDO. Forces all SRAM outputs to high Z state. IDCODE 001 Loads the ID register with the vendor ID code and places the register between TDI and TDO. This operation does not affect SRAM operation. SAMPLE Z 010 Captures the input/output contents. Places the boundary scan register between TDI and TDO. Forces all SRAM output drivers to a high Z state. RESERVED 011 Do Not Use: This instruction is reserved for future use. SAMPLE/PRELOAD 100 Captures the input/output ring contents. Places the boundary scan register between TDI and TDO. Does not affect the SRAM operation. RESERVED 101 Do Not Use: This instruction is reserved for future use. RESERVED 110 Do Not Use: This instruction is reserved for future use. BYPASS 111 Places the bypass register between TDI and TDO. This operation does not affect SRAM operation. Note 16. All voltages referenced to VSS (GND). Document Number: 38-05537 Rev. *P Page 18 of 34 CY7C1354CV25 CY7C1356CV25 Boundary Scan Exit Order (continued) Boundary Scan Exit Order (256 K × 36) (256 K × 36) Bit # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 119-ball ID K4 H4 M4 F4 B4 G4 C3 B3 D6 H7 G6 E6 D7 E7 F6 G7 H6 T7 K7 L6 N6 P7 N7 M6 L7 K6 P6 T4 A3 C5 B5 A5 C6 A6 P4 N4 R6 T5 T3 R2 R3 P2 P1 Document Number: 38-05537 Rev. *P 165-ball ID B6 B7 A7 B8 A8 A9 B10 A10 C11 E10 F10 G10 D10 D11 E11 F11 G11 H11 J10 K10 L10 M10 J11 K11 L11 M11 N11 R11 R10 P10 R9 P9 R8 P8 R6 P6 R4 P4 R3 P3 R1 N1 L2 Bit # 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 119-ball ID 165-ball ID L2 K2 K1 J2 N2 M2 N1 M1 M2 L1 L1 K1 K2 J1 Not Bonded (Preset to 1) Not Bonded (Preset to 1) H1 G2 G2 F2 E2 E2 D1 D2 H2 G1 G1 F1 F2 E1 E1 D1 D2 C1 C2 B2 A2 A2 E4 A3 B2 B3 L3 B4 G3 A4 G5 A5 L5 B5 B6 A6 Page 19 of 34 CY7C1354CV25 CY7C1356CV25 Boundary Scan Exit Order (continued) Boundary Scan Exit Order (512 K × 18) (512 K × 18) Bit # 119-ball ID 165-ball ID 1 K4 B6 2 H4 B7 3 M4 A7 4 F4 B8 5 B4 A8 6 G4 A9 7 C3 B10 8 B3 A10 9 T2 A11 10 Not Bonded (Preset to 0) Not Bonded (Preset to 0) 11 Not Bonded (Preset to 0) Not Bonded (Preset to 0) 12 Not Bonded (Preset to 0) Not Bonded (Preset to 0) 13 D6 C11 14 E7 D11 15 F6 E11 16 G7 F11 17 H6 G11 18 T7 H11 19 K7 J10 20 L6 K10 21 N6 L10 22 P7 M10 23 Not Bonded (Preset to 0) Not Bonded (Preset to 0) 24 Not Bonded (Preset to 0) Not Bonded (Preset to 0) 25 Not Bonded (Preset to 0) Not Bonded (Preset to 0) 26 Not Bonded (Preset to 0) Not Bonded (Preset to 0) 27 Not Bonded (Preset to 0) Not Bonded (Preset to 0) 28 T6 R11 29 A3 R10 30 C5 P10 31 B5 R9 32 A5 P9 33 C6 R8 34 A6 P8 35 P4 R6 36 N4 P6 37 R6 R4 38 T5 P4 Document Number: 38-05537 Rev. *P Bit # 119-ball ID 165-ball ID 39 T3 R3 40 R2 P3 41 R3 R1 42 Not Bonded (Preset to 0) Not Bonded (Preset to 0) 43 Not Bonded (Preset to 0) Not Bonded (Preset to 0) 44 Not Bonded (Preset to 0) Not Bonded (Preset to 0) 45 Not Bonded (Preset to 0) Not Bonded (Preset to 0) 46 P2 N1 47 N1 M1 48 M2 L1 49 L1 K1 K2 J1 50 51 Not Bonded (Preset to 1) Not Bonded (Preset to 1) 52 H1 G2 53 G2 F2 54 E2 E2 55 D1 D2 56 Not Bonded (Preset to 0) Not Bonded (Preset to 0) 57 Not Bonded (Preset to 0) Not Bonded (Preset to 0) 58 Not Bonded (Preset to 0) Not Bonded (Preset to 0) 59 Not Bonded (Preset to 0) Not Bonded (Preset to 0) 60 Not Bonded (Preset to 0) Not Bonded (Preset to 0) 61 C2 B2 62 A2 A2 63 E4 A3 B2 B3 64 65 Not Bonded (Preset to 0) Not Bonded (Preset to 0) 66 G3 Not Bonded (Preset to 0) 67 Not Bonded (Preset to 0) A4 68 L5 B5 69 B6 A6 69 B6 A6 69 B6 A6 68 L5 B5 69 B6 A6 66 G3 Not Bonded (Preset to 0) 67 Not Bonded (Preset to 0) A4 68 L5 B5 69 B6 A6 Page 20 of 34 CY7C1354CV25 CY7C1356CV25 Maximum Ratings Exceeding maximum ratings may shorten the useful life of the device. User guidelines are not tested. Storage temperature ................................ –65 °C to +150 °C Ambient temperature with power applied .......................................... –55 °C to +125 °C Supply voltage on VDD relative to GND .......–0.5 V to +3.6 V Supply voltage on VDDQ relative to GND ...... –0.5 V to +VDD DC to outputs in tri-state ...................–0.5 V to VDDQ + 0.5 V DC input voltage ................................. –0.5 V to VDD + 0.5 V Current into outputs (LOW) ........................................ 20 mA Static discharge voltage (per MIL-STD-883, method 3015) ......................... > 2001 V Latch-up current ................................................... > 200 mA Operating Range Range Ambient Temperature VDD/VDDQ 0 °C to +70 °C 2.5 V ± 5% Commercial Industrial –40 °C to +85 °C Electrical Characteristics Over the Operating Range Parameter [17, 18] Description Test Conditions VDD Power supply voltage VDDQ I/O supply voltage for 2.5 V I/O VOH Output HIGH voltage for 2.5 V I/O, IOH = 1.0 mA VOL Output LOW voltage for 2.5 V I/O, IOL= 1.0 mA Min Max Unit 2.375 2.625 V 2.375 VDD V 2.0 – V – 0.4 V VIH Input HIGH voltage for 2.5 V I/O 1.7 VDD + 0.3 V V VIL Input LOW voltage [17] for 2.5 V I/O –0.3 0.7 V IX Input leakage current except ZZ GND VI VDDQ and MODE –5 5 A Input current of MODE Input = VSS –30 – A Input = VDD – 5 A Input current of ZZ Input = VSS –5 – A Input = VDD – 30 A IOZ Output leakage current GND VI VDDQ, output disabled –5 5 A IDD VDD operating supply VDD = Max, IOUT = 0 mA, f = fMAX = 1/tCYC 4-ns cycle, 250 MHz – 250 mA 5-ns cycle, 200 MHz – 220 mA 6-ns cycle, 166 MHz – 180 mA 4-ns cycle, 250 MHz – 130 mA 5-ns cycle, 200 MHz – 120 mA 6-ns cycle, 166 MHz – 110 mA – 40 mA ISB1 ISB2 Automatic CE power-down current — TTL inputs Automatic CE power-down current — CMOS inputs Max VDD, device deselected, VIN VIH or VIN VIL, f = fMAX = 1/tCYC Max VDD, device deselected, All speed VIN 0.3 V or VIN > VDDQ 0.3 V, grades f=0 Notes 17. Overshoot: VIH(AC) < VDD + 1.5 V (Pulse width less than tCYC/2), undershoot: VIL(AC) > –2 V (Pulse width less than tCYC/2). 18. TPower-up: Assumes a linear ramp from 0 V to VDD(min) within 200 ms. During this time VIH < VDD and VDDQ VDD. Document Number: 38-05537 Rev. *P Page 21 of 34 CY7C1354CV25 CY7C1356CV25 Electrical Characteristics (continued) Over the Operating Range Parameter [17, 18] Description Automatic CE power-down current — CMOS inputs ISB3 ISB4 Automatic CE power-down current — TTL inputs Test Conditions Min Max Unit Max VDD, device deselected, 4-ns cycle, VIN 0.3 V or VIN > VDDQ 0.3 V, 250 MHz f = fMAX = 1/tCYC 5-ns cycle, 200 MHz – 120 mA – 110 mA 6-ns cycle, 166 MHz – 100 mA All speed grades – 40 mA Max VDD, device deselected, VIN VIH or VIN VIL, f = 0 Capacitance Parameter [19] Description Test Conditions CIN Input capacitance CCLK Clock input capacitance CI/O Input/output capacitance 100-pin TQFP 119-ball BGA 165-ball FBGA Unit Max Max Max TA = 25 °C, f = 1 MHz, VDD = 2.5 V, VDDQ = 2.5 V 5 5 5 pF 5 5 5 pF 5 7 7 pF Thermal Resistance Parameter [19] Description JA Thermal resistance (junction to ambient) JC Thermal resistance (junction to case) Test Conditions Test conditions follow standard test methods and procedures for measuring thermal impedance, per EIA/JESD51. 100-pin TQFP 119-ball BGA 165-ball FBGA Unit Package Package Package 29.41 34.1 16.8 °C/W 6.13 14 3.0 °C/W AC Test Loads and Waveforms Figure 4. AC Test Loads and Waveforms 2.5 V I/O Test Load R = 1667 2.5 V OUTPUT OUTPUT RL = 50 Z0 = 50 VT = 1.25 V (a) ALL INPUT PULSES VDDQ GND 5 pF INCLUDING JIG AND SCOPE R = 1538 (b) 10% 90% 10% 90% 1 ns 1 ns (c) Note 19. Tested initially and after any design or process change that may affect these parameters. Document Number: 38-05537 Rev. *P Page 22 of 34 CY7C1354CV25 CY7C1356CV25 Switching Characteristics Over the Operating Range Parameter [20, 21] tPower[22] -250 Description VCC(typical) to the first access read or write -200 -166 Min Max Min Max Min Max 1 – 1 – 1 – Unit ms Clock tCYC Clock cycle time FMAX Maximum operating frequency 4.0 – 5 – 6 – ns – 250 – 200 – 166 MHz tCH Clock HIGH 1.8 – 2.0 – 2.4 – ns tCL Clock LOW 1.8 – 2.0 – 2.4 – ns Output Times tCO Data output valid after CLK rise – 2.8 – 3.2 – 3.5 ns tEOV OE LOW to output valid – 2.8 – 3.2 – 3.5 ns tDOH Data output hold after CLK rise 1.25 – 1.5 – 1.5 – ns 1.25 2.8 1.5 3.2 1.5 3.5 ns 1.25 – 1.5 – 1.5 – ns – 2.8 – 3.2 – 3.5 ns 0 – 0 – 0 – ns [23, 24, 25] tCHZ Clock to high Z tCLZ Clock to low Z [23, 24, 25] tEOHZ tEOLZ OE HIGH to output high Z OE LOW to output low Z [23, 24, 25] [23, 24, 25] Set-up Times tAS Address set-up before CLK rise 1.4 – 1.5 – 1.5 – ns tDS Data input set-up before CLK rise 1.4 – 1.5 – 1.5 – ns tCENS CEN set-up before CLK rise 1.4 – 1.5 – 1.5 – ns tWES WE, BWx set-up before CLK rise 1.4 – 1.5 – 1.5 – ns tALS ADV/LD set-up before CLK rise 1.4 – 1.5 – 1.5 – ns tCES Chip select set-up 1.4 – 1.5 – 1.5 – ns tAH Address hold after CLK rise 0.4 – 0.5 – 0.5 – ns tDH Data input hold after CLK rise 0.4 – 0.5 – 0.5 – ns tCENH CEN hold after CLK rise 0.4 – 0.5 – 0.5 – ns tWEH WE, BWx hold after CLK rise 0.4 – 0.5 – 0.5 – ns tALH ADV/LD hold after CLK rise 0.4 – 0.5 – 0.5 – ns tCEH Chip select hold after CLK rise 0.4 – 0.5 – 0.5 – ns Hold Times Notes 20. Timing reference level is when VDDQ = 2.5 V. 21. Test conditions shown in (a) of Figure 4 on page 22 unless otherwise noted. 22. This part has a voltage regulator internally; tpower is the time power needs to be supplied above VDD minimum initially, before a Read or Write operation can be initiated. 23. tCHZ, tCLZ, tEOLZ, and tEOHZ are specified with AC test conditions shown in (b) of Figure 4 on page 22. Transition is measured ± 200 mV from steady-state voltage. 24. At any given voltage and temperature, tEOHZ is less than tEOLZ and tCHZ is less than tCLZ to eliminate bus contention between SRAMs when sharing the same data bus. These specifications do not imply a bus contention condition, but reflect parameters guaranteed over worst case user conditions. Device is designed to achieve high Z prior to low Z under the same system conditions. 25. This parameter is sampled and not 100% tested. Document Number: 38-05537 Rev. *P Page 23 of 34 CY7C1354CV25 CY7C1356CV25 Switching Waveforms Figure 5. Read/Write Timing [26, 27, 28] 1 2 3 t CYC 4 5 6 A3 A4 7 8 9 A5 A6 A7 10 CLK tCENS tCENH tCL tCH CEN tCES tCEH CE ADV/LD WE BWX A1 ADDRESS A2 tCO tAS tDS tAH Data In-Out (DQ) tDH D(A1) tCLZ D(A2) D(A2+1) tDOH Q(A3) tOEV Q(A4) tCHZ Q(A4+1) D(A5) Q(A6) tOEHZ tDOH tOELZ OE WRITE D(A1) WRITE D(A2) BURST WRITE D(A2+1) READ Q(A3) READ Q(A4) DON’T CARE BURST READ Q(A4+1) WRITE D(A5) READ Q(A6) WRITE D(A7) DESELECT UNDEFINED Notes 26. For this waveform ZZ is tied LOW. 27. When CE is LOW, CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH, CE1 is HIGH or CE2 is LOW or CE3 is HIGH. 28. Order of the Burst sequence is determined by the status of the MODE (0 = Linear, 1 = Interleaved). Burst operations are optional. Document Number: 38-05537 Rev. *P Page 24 of 34 CY7C1354CV25 CY7C1356CV25 Switching Waveforms (continued) Figure 6. NOP, STALL and DESELECT CYCLES [29, 30, 31] 1 2 A1 A2 3 4 5 A3 A4 6 7 8 9 10 CLK CEN CE ADV/LD WE BWX ADDRESS A5 tCHZ D(A1) Data Q(A2) D(A4) Q(A3) Q(A5) In-Out (DQ) WRITE D(A1) READ Q(A2) STALL READ Q(A3) WRITE D(A4) STALL DON’T CARE NOP READ Q(A5) DESELECT CONTINUE DESELECT UNDEFINED Notes 29. For this waveform ZZ is tied LOW. 30. When CE is LOW, CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH, CE1 is HIGH or CE2 is LOW or CE3 is HIGH. 31. The IGNORE CLOCK EDGE or STALL cycle (Clock 3) illustrated CEN being used to create a pause. A write is not performed during this cycle. Document Number: 38-05537 Rev. *P Page 25 of 34 CY7C1354CV25 CY7C1356CV25 Switching Waveforms (continued) Figure 7. ZZ Mode Timing [32, 33] CLK t ZZ ZZ I t ZZREC t ZZI SUPPLY I DDZZ t RZZI ALL INPUTS (except ZZ) Outputs (Q) DESELECT or READ Only High-Z DON’T CARE Notes 32. Device must be deselected when entering ZZ mode. See cycle description table for all possible signal conditions to deselect the device. 33. I/Os are in high Z when exiting ZZ sleep mode. Document Number: 38-05537 Rev. *P Page 26 of 34 CY7C1354CV25 CY7C1356CV25 Ordering Information Cypress offers other versions of this type of product in many different configurations and features. The below table contains only the list of parts that are currently available.For a complete listing of all options, visit the Cypress website at www.cypress.com and refer to the product summary page at http://www.cypress.com/products or contact your local sales representative. Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives and distributors. To find the office closest to you, visit us at http://www.cypress.com/go/datasheet/offices. Speed (MHz) 166 Ordering Code CY7C1354CV25-166AXC Package Diagram Part and Package Type 51-85050 100-pin TQFP (14 × 20 × 1.4 mm) Pb-free Operating Range Commercial CY7C1356CV25-166AXC 200 CY7C1354CV25-166BZC 51-85180 165-ball FBGA (13 × 15 × 1.4 mm) CY7C1354CV25-200AXC 51-85050 100-pin TQFP (14 × 20 × 1.4 mm) Pb-free Commercial Ordering Code Definitions CY 7 C 135X C V25 - XXX XX X C Temperature Range: C = Commercial Pb-free Package Type: XX = A or BZ A = 100-pin TQFP BZ = 165-ball FBGA Speed Grade: XXX = 166 MHz or 200 MHz V25 = 2.5 V Process Technology 90 nm 135X = 1354 or 1356 1354 = PL, 256 Kb × 36 (9 Mb) 1356 = PL, 512 Kb × 18 (9 Mb) Technology Code: C = CMOS Marketing Code: 7 = SRAM Company ID: CY = Cypress Document Number: 38-05537 Rev. *P Page 27 of 34 CY7C1354CV25 CY7C1356CV25 Package Diagrams Figure 8. 100-pin TQFP (14 × 20 × 1.4 mm) A100RA Package Outline, 51-85050 51-85050 *E Document Number: 38-05537 Rev. *P Page 28 of 34 CY7C1354CV25 CY7C1356CV25 Package Diagrams (continued) Figure 9. 119-ball PBGA (14 × 22 × 2.4 mm) BG119 Package Outline, 51-85115 51-85115 *D Document Number: 38-05537 Rev. *P Page 29 of 34 CY7C1354CV25 CY7C1356CV25 Package Diagrams (continued) Figure 10. 165-ball FBGA (13 × 15 × 1.4 mm) BB165D/BW165D (0.5 Ball Diameter) Package Outline, 51-85180 51-85180 *G Document Number: 38-05537 Rev. *P Page 30 of 34 CY7C1354CV25 CY7C1356CV25 Acronyms Acronym Document Conventions Description Units of Measure BGA Ball Grid Array CE Chip Enable °C degree Celsius CEN Clock Enable MHz megahertz CMOS Complementary Metal Oxide Semiconductor µA microampere EIA Electronic Industries Alliance mA milliampere FBGA Fine-Pitch Ball Grid Array mm millimeter I/O Input/Output ms millisecond JEDEC Joint Electron Devices Engineering Council mV millivolt JTAG Joint Test Action Group LSB Least Significant Bit MSB Most Significant Bit NoBL No Bus Latency OE Output Enable SRAM Static Random Access Memory TAP Test Access Port TCK Test Clock TDI Test Data-In TDO Test Data-Out TMS Test mode select TQFP Thin Quad Flat Pack TTL Transistor-Transistor Logic WE Write Enable Document Number: 38-05537 Rev. *P Symbol Unit of Measure ns nanosecond ohm % percent pF picofarad V volt W watt Page 31 of 34 CY7C1354CV25 CY7C1356CV25 Document History Page Document Title: CY7C1354CV25/CY7C1356CV25, 9-Mbit (256 K × 36/512 K × 18) Pipelined SRAM with NoBL™ Architecture Document Number: 38-05537 Rev. ECN No. Issue Date Orig. of Change ** 242032 See ECN RKF New data sheet RKF Changed Boundary Scan order to match the B Rev of these devices Description of Change *A 278969 See ECN *B 284929 See ECN *C 323636 See ECN PCI Changed frequency of 225 MHz into 250 MHz Added tCYC of 4.0 ns for 250 MHz Changed JA and JC for TQFP Package from 25 and 9 °C/W to 29.41 and 6.13 °C/W respectively Changed JA and JC for BGA Package from 25 and 6 °C/W to 34.1 and 14.0 °C/W respectively Changed JA and JC for FBGA Package from 27 and 6 °C/W to 16.8 and 3.0 °C/W respectively Modified address expansion as per JEDEC Standard Removed comment of Lead-free BG and BZ packages availability *D 332879 See ECN PCI Unshaded 200 and 166 MHz speed bin in the AC/DC Table and Selection Guide Added Address Expansion pins in the Pin Definition Table Removed description of Extest Output Bus Tri-state on page # 11 Modified VOL, VOH test conditions Updated Ordering Information Table *E 357258 See ECN PCI Changed from Preliminary to Final Changed ISB2 from 35 to 40 mA Removed Shading on 250MHz Speed Bin in Selection Guide and AC/DC Table Updated Ordering Information Table RKF / VBL Included DC Characteristics Table Changed ISB1 and ISB3 from DC Characteristic table as follows: ISB1: 225 MHz -> 130 mA, 200 MHz -> 120 mA, 167 MHz -> 110 mA ISB3: 225 MHz -> 120 mA, 200 MHz -> 110 mA, 167 MHz -> 100 mA Changed IDDZZ to 50mA. Added BG and BZ pkg lead-free part numbers to ordering info section. *F 377095 See ECN PCI Modified test condition in note# 15 from VDDQ < VDD to VDDQ VDD *G 408298 See ECN RXU Changed address of Cypress Semiconductor Corporation on Page# 1 from “3901 North First Street” to “198 Champion Court” Changed three-state to tri-state. Modified “Input Load” to “Input Leakage Current except ZZ and MODE” in the Electrical Characteristics Table. Replaced Package Name column with Package Diagram in the Ordering Information table. Updated the Ordering Information Table. *H 501793 See ECN VKN Added the Maximum Rating for Supply Voltage on VDDQ Relative to GND Changed tTH, tTL from 25 ns to 20 ns and tTDOV from 5 ns to 10 ns in TAP AC Switching Characteristics table. Updated the Ordering Information table. *I 2898958 03/25/10 NJY Removed inactive parts from the ordering information table. Updated package diagrams. *J 3033272 09/19/2010 NJY Added Ordering Code Definitions under Ordering Information. Added Acronyms and Units of Measure. Minor edits. Updated to new template. *K 3052726 10/08/10 NJY Removed pruned part CY7C1356CV25-200AXC from the ordering information table. *L 3385314 09/29/2011 PRIT Updated Package Diagrams. Document Number: 38-05537 Rev. *P Page 32 of 34 CY7C1354CV25 CY7C1356CV25 Document History Page (continued) Document Title: CY7C1354CV25/CY7C1356CV25, 9-Mbit (256 K × 36/512 K × 18) Pipelined SRAM with NoBL™ Architecture Document Number: 38-05537 Rev. ECN No. Issue Date Orig. of Change Description of Change *M 3754566 09/25/2012 PRIT Updated Package Diagrams (spec 51-85115 (Changed revision from *C to *D), spec 51-85180 (Changed revision from *C to *F)). *N 4537527 10/14/2014 PRIT Updated Package Diagrams: spec 51-85050 – Changed revision from *D to *E. Updated to new template. Completing Sunset Review. *O 4571917 11/18/2014 PRIT Updated Functional Description: Added “For a complete list of related documentation, click here.” at the end. *P 4974141 10/19/2015 PRIT Updated Package Diagrams: spec 51-85180 – Changed revision from *F to *G. Updated to new template. Completing Sunset Review. Document Number: 38-05537 Rev. *P Page 33 of 34 CY7C1354CV25 CY7C1356CV25 Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. PSoC® Solutions Products Automotive Clocks & Buffers Interface Lighting & Power Control Memory cypress.com/go/automotive cypress.com/go/clocks cypress.com/go/interface cypress.com/go/powerpsoc cypress.com/go/memory PSoC cypress.com/go/psoc Touch Sensing cypress.com/go/touch USB Controllers Wireless/RF psoc.cypress.com/solutions PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP Cypress Developer Community Community | Forums | Blogs | Video | Training Technical Support cypress.com/go/support cypress.com/go/USB cypress.com/go/wireless © Cypress Semiconductor Corporation, 2004-2015. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement. Document Number: 38-05537 Rev. *P Revised October 19, 2015 Page 34 of 34 NoBL and No Bus Latency are trademarks of Cypress Semiconductor Corporation. ZBT is a trademark of Integrated Device Technology, Inc. All products and company names mentioned in this document may be the trademarks of their respective holders.