MURATA UVQ-2.5/40-D48N-C

UVQ Series
www.murata-ps.com
Low Profile, Isolated Quarter Brick
2.5–40 Amp DC/DC Converters
ORDERING GUIDE SUMMARY
Model
VOUT Range
IOUT Range
VIN Range
Efficiency
All Models
1.2V to 48V
2.5A to 40A
18-36V or 36-75V
Up to 92.%, model dependent
INPUT CHARACTERISTICS
Parameter
Typ. @ 25°C, full load
Voltage Range
Typical unit
Notes
18-36 or 36-75 Volts
24V or 48V nominal
Current, full power
Up to 5.6 Amps
Model dependent
Isolation
2kVdc to 2250V
Model dependent
Remote On/Off Control
Switch or FET control
Positive or negative logic
FEATURES
OUTPUT CHARACTERISTICS
■
Standard quarter-brick package/pinout
Parameter
■
Outputs from 1.5 to 48V up to 125W
Voltage
■
Typ. @ 25°C, full load
1.5 to 48 Volts ±10%
Notes
Trimmable
Low profile 0.42" height
Current
2.5 to 40 Amps fullscale
No minimum load
■
24 and 48Vdc nominal inputs
Accuracy
Down to 1% of VNOM
Most models
■
Fully isolated, 2250Vdc (BASIC) insulation
Ripple & Noise (to 20MHz)
Down to 35mVp-p
Model dependent
Line and Load Regulation
Down to ±0.125%/±0.25%
Model dependent
Overcurrent Protection
150% of IOUT max.
With hiccup auto-restart
Overtemperature Protection
+125°C
Efficiency (minimum)
See Performance Specifications
■
Designed for RoHS compliance
■
Output overvoltage/short-circuit protected
■
On/Off control, trim and sense functions
■
High efficiency to 92%
■
Protected against temp. and voltage limits
GENERAL SPECIFICATIONS
■
Designed to meet UL/IEC/EN60950-1 safety
approvals
Parameter
Typ. @ 25°C, full load
Dynamic Load Response
Down to 50μsec
Notes
Model dependent
Operating Temperature Range
–40 to +110°C
With baseplate, see derating curve
Safety
UL/IEC/EN 60950-1
and CSA C22.2-No.234
MECHANICAL CHARACTERISTICS
With baseplate
1.45 x 2.30 x 0.5 inches (36.83 x 58.42 x 12.7 mm)
Without baseplate
1.45 x 2.30 x 0.42 inches (36.83 x 58.42 x 10.67 mm)
See Performance Specifications, page 2
PRODUCT OVERVIEW
For efficient, fully isolated DC power in the smallest space, Murata Power Solutions' UVQ series
quarter bricks offer output voltages from 1.5
to 48 Volts with currents up to 40 Amps. UVQs
operate over a wide temperature range (up to
+70°C at 200 lfm airflow) at full-rated power. The
optional mounting baseplate extends this to all
practical temperature ranges at full power.
UVQ’s achieve these impressive specifications
while delivering excellent electrical performance.
Overall noise is 35mVp-p (3.3V models) with fast
step response (down to 50μsec). These converters
For full details go to
www.murata-ps.com/rohs
offer high stability even with no load and tight output regulation. The unit is fully protected against
input over and undervoltage, output overcurrent and short circuit. An on-board temperature
sensor shuts down the converter if thermal limits
are reached. Protection uses the “hiccup” (auto
restart) method.
A convenient remote On/Off control input operates by external digital logic, relay or transistor
input. To compensate for longer wiring and to
retain output voltage accuracy at the load, UVQ’s
include a Sense input to dynamically correct for
ohmic losses. A trim input may be connected to a
user’s adjustment potentiometer or trim resistors
for output voltage calibration closer than the
standard accuracy.
UVQ’s include industry-standard safety certifications and BASIC I/O insulation provides 2250
Volt input/output isolation. Radiation emission
testing is performed to widely-accepted EMC
standards. The UVQ’s may be considered as
higher performance replacements for some MPS
USQ models.
Pb
Lead-free
construction/attach
www.murata-ps.com
Technical enquiries email: [email protected], tel: +1 508 339 3000
MDC_UVQ Models.B11 Page 1 of 25
UVQ Series
Low Profile, Isolated Quarter Brick
2.5–40 Amp DC/DC Converters
Performance Specifications and Ordering Guide ➀
ORDERING GUIDE
Output
Root Models
VOUT
(Volts)
UVQ-1.5/40-D24P-C
UVQ-2.5/35-D24P-C
UVQ-2.5/40-D48N-C
UVQ-3.3/30-D24P-C
UVQ-3.3/35-D48N-C
UVQ-5/20-D24P-C
UVQ-5/20-D48N-C
UVQ-12/8-D24P-C
UVQ-12/10-D48N-C
UVQ-15/7-D24P-C
UVQ-15/7-D48N-C
UVQ-18/5.6-D24P-C
UVQ-18/6-D48N-C
UVQ-24/4.5-D24P-C
UVQ-24/4.5-D48N-C
UVQ-48/2.5-D24P-C
UVQ-48/2.5-D48N-C
1.5
IOUT
Power
(Amps) (Watts)
40
35
40
30
35
60
87.5
100
99
115.5
5
20
100
12
8
10
96
120
15
7
105
18
5.6
6
100.8
24
4.5
48
2.5
2.5
3.3
108
120
Input
R/N (mVp-p) ➁
Regulation (Max.) ➂
Typ.
Max.
Line
Load
VIN Nom.
(Volts)
30
60
60
60
65
40
50
25
130
160
150
150
185
185
100
130
200
375
±0.075%
±0.05%
±0.05%
±0.1%
±0.05%
±0.05%
±0.05%
±0.1%
±0.075%
±0.05%
±0.05%
±0.05%
±0.05%
±0.075%
±0.075%
±0.1%
±0.175%
±0.05%
±0.05%
±0.05%
±0.25%
±0.25%
±0.05%
±0.05%
±0.1%
±0.05%
±0.05%
±0.02%
±0.075%
±0.075%
±0.15%
±0.25%
±0.2%
±0.2%
24
24
48
24
48
24
48
24
48
24
48
24
48
24
48
24
48
35
30
20
95
110
85
120
125
125
60
75
100
250
c These are partial model numbers. Please refer to the full model number structure for complete ordering part numbers.
d Min. IOUT = 3 Amps.
e All specifications are at nominal line voltage and full load, +25°C unless otherwise noted. See detailed specifications.
UVQ Pin 9 Baseplate Connection
The UVQ series may include an optional installed baseplate for extended
thermal management. Various UVQ models (see list below) are also available
with an additional pin 9 on special order which connects to the baseplate but is
electrically isolated from the rest of the converter. Please refer to the mechanical drawings.
Pin 9 offers a positive method of controlling the electrical potential of the
baseplate, independent of the converter. Some baseplate models cannot
include pin 9 and in such cases, the baseplate is grounded by the mounting
bolts. Or consider adding an external lugged washer with a grounding terminal.
The baseplate may be ordered by adding a “B” to the model number tree
and pin 9 will be pre-installed by adding a “9”. The two options are separate.
Please refer to the Ordering Guide. Do not order pin 9 without the baseplate.
Note that “pin 9” converters may be on limited forecast, requiring minimum
order quantities and scheduled deliveries.
www.murata-ps.com
Range IIN, No Load IIN, Full Load
(Volts)
(mA)
(Amps)
18-36
18-36
36-75
18-36
36-75
18-36
36-75
18-36
36-75
18-36
36-75
18-36
36-75
18-36
36-75
18-36
36-75
80
100
100
180
130
180
80
90
60
103
60
140
80
45
45
45
30
2.84
4.14
2.37
4.58
2.7
4.53
2.31
4.4
2.78
4.85
2.39
4.69
2.5
5.03
2.49
4.4
2.71
Efficiency)
Min.
Typ.
86.5%
86%
87%
88.5%
87%
91%
88.5%
89%
88.5%
88.5%
90%
88%
88.3%
88%
89%
89%
91%
88%
88%
88%
90%
89%
92%
90%
91%
90%
90.3%
91.5%
89.5%
90%
89.5%
90.5%
91%
92.3%
Package
(Case,
Pinout)
C59, P32
Output capacitors are 1uF ceramic || 10 uF electrolytic. Input cap is 22 uF, low
ESR, except UVQ-24/4.5 is 33uF and UVQ-48/2.5 uses no input cap. I/O caps are
necessary for our test equipment and may not be needed for your application.
f IOUT = 14 Amps max. with VIN = 18-19.5 Volts.
Models available with Pin 9:
UVQ-12/10-D48
UVQ-1.5/40-D24
Models which are NOT available with Pin 9:
UVQ-5/20-D24 and –D48
UVQ-3.3/30-D24
UVQ-3.3/35-D48
UVQ-2.5/35-D24
UVQ-2.5/40-D48
Other models which are not listed will be reviewed for future pin 9 accomodation.
Technical enquiries email: [email protected], tel: +1 508 339 3000
MDC_UVQ Models.B11 Page 2 of 25
UVQ Series
Low Profile, Isolated Quarter Brick
2.5–40 Amp DC/DC Converters
PART NUMBER STRUCTURE
U VQ - 3.3 / 20 - D48 N B 9 LX - C
RoHS-6 hazardous substance compliant
Output Configuration
U = Unipolar/Single
Alternate Pin Length: (special quantity order)
Blank = Standard pin length
L1 = 0.110 (2.79mm)
L2 = 0.145 (3.68mm)
Quarter-Brick Package
Nominal Output Voltage
Baseplate Pin 9, see Mechanical Drawings: (special order)
1.2 to 48 Volts
Blank = No pin 9, standard
9 = Pin 9 installed (see description on pg. 2), optional
Maximum Rated Output
Current in Amps
Blank = No baseplate, standard
B = Baseplate installed, optional special order
Input Voltage Range:
D24 = 18-36 Volts (24V nominal)
D48 = 36-75 Volts (48V nominal)
* Note:
Remote On/Off Control Polarity:
Some model number combinations may not be
Add "P" for positive polarity
available. Contact Murata Power Solutions..
Add "N" for negative polarity
Positive "P" polarity is standard for D24 models and
optional special order for D48 models. Negative "N"
polarity is standard for D48 models and optional special
order for D24 models.
+SENSE
(7)
+VOUT
(8)
+VIN
(3)
Baseplate
(9)
Optional
SWITCH
CONTROL
–VOUT
(4)
–VIN
(1)
–SENSE
(5)
PWM
CONTROLLER
OPTO
ISOLATION
INPUT UNDERVOLTAGE, INPUT
OVERVOLTAGE, AND OUTPUT
OVERVOLTAGE COMPARATORS
REMOTE
ON/OFF
CONTROL*
(2)
REFERENCE &
ERROR AMP
VOUT
TRIM
(6)
* Can be ordered with positive (standard) or negative (optional) polarity.
Typical configuration — some models use a different topology
Figure 1. Simplified Schematic
www.murata-ps.com
Technical enquiries email: [email protected], tel: +1 508 339 3000
MDC_UVQ Models.B11 Page 3 of 25
UVQ Series
Low Profile, Isolated Quarter Brick
2.5–40 Amp DC/DC Converters
Performance/Functional Specifications 24V Models
UVQ-48/2.5-D24
17
UVQ-24/4.5-D24
UVQ-5/20-D24
17
UVQ-18/5.6-D24
UVQ-3.3/30-D24
17
UVQ-15/7-D24
UVQ-2.5/35-D24
17
17
17
17
17
17
16.25
16
16.25
16
16
UVQ-12/8-D24
UVQ-1.5/40-D24
Typical @ TA = +25°C under nominal line voltage, nominal output voltage, natural air convection, external caps and full-load conditions, unless noted. (1)
Input
Input voltage range
Start-up threshold, (V) min.
See ordering guide
Undervoltage
shutdown, (V)14
16
Overvoltage shutdown (V)
none
39
Reflected (back) ripple
current2
none
10-50 mA pk-pk, model dependent
Input Current
Full load conditions
Inrush transient, (A2sec)
See ordering guide.
0.5
0.5
0.05
0.5
1
1
0.05
0.05
Output short circuit, (mA)
40
10
320
50
50
50
No load, mA
80
100
180
160
90
103
140
45
30
3.79
5.49
6.04
5.57
5.93
6.52
6.29
6.67
3.60
Low line (VIN = min.),
(Amps)
50
0.1
Standby mode,
(Off, UV, OT shutdown)
Internal input filter type
1-4mA, model dependent
L-C
Pi-type
Reverse polarity
protection
L-C
See notes.
Remote On/Off Control5
Positive logic, "P" suffix
(specifications are max)
OFF = Ground pin to +0.8V
ON = Open or +5V to +VIN max.
Negative logic, "N" suffix
(specifications are max)
OFF = Open or +5V to +VIN max
ON = Ground pin to+0.8V max
Current
1-8 mA, model dependent
www.murata-ps.com
Technical enquiries email: [email protected], tel: +1 508 339 3000
MDC_UVQ Models.B11 Page 4 of 25
UVQ Series
Low Profile, Isolated Quarter Brick
2.5–40 Amp DC/DC Converters
Performance/Functional Specifications 24V Models
UVQ-48/2.5-D24
UVQ-24/4.5-D24
UVQ-18/5.6-D24
UVQ-15/7-D24
UVQ-12/8-D24
UVQ-5/20-D24
UVQ-3.3/30-D24
UVQ-2.5/35-D24
UVQ-1.5/40-D24
Typical @ TA = +25°C under nominal line voltage, nominal output voltage, natural air convection, external caps and full-load conditions, unless noted. (1)
Output
Voltage output range
See ordering guide.
Voltage output accuracy
(50% load)
±1.5% of VNOM
±1.25% of VNOM
Adjustment range
–20 to +10% of VNOM.
±10% of VNOM.
±0.02% of VOUT range per °C
Temperature coefficient
Minimum loading
No minimum load
3 amps
No minimum load
Remote sense
compensation
+10%.
Ripple/noise
See ordering guide.
Line/Load regulation
See ordering guide.
Efficiency
See ordering guide.
Maximum capacitive
loading, Low ESR
<0.02Ω max.,
resistive load, (μF)
Current limit inception
(98% of VOUT, after
warmup), (Amps)
10,000
45
5000
44
36
Short circuit protection
method
Short circuit current,
(Amps)
4700
24
10
9.5
2200
7
5.8
3.4
5
2.8
Current limiting, hiccup autorestart. Remove overload for recovery.
3.6
3
3
Short circuit duration
Overvoltage protection, (via
magnetic feedback)
±1% of VNOM
3
1.5
15 mA
3
Output may be shorted continuously to ground (no damage).
2.3 Volts
3 Volts max
4 Volts max 6.8 Volts max
14.4 Volts
max
18.5 Volts
22 Volts max 29 Volts max 59 Volts max
Isolation Characteristics
Isolation Voltage
Input to Output, (Volts min)
2000
Input to baseplate
1500
Baseplate to output,
(Volts min)
1500
1000
Isolation resistance
Isolation capacitance, (pF)
1500
100 MΩ
1500
Isolation safety rating
1000
2000
50
Basic insulation
www.murata-ps.com
Technical enquiries email: [email protected], tel: +1 508 339 3000
MDC_UVQ Models.B11 Page 5 of 25
UVQ Series
Low Profile, Isolated Quarter Brick
2.5–40 Amp DC/DC Converters
Performance/Functional Specifications 24V Models
UVQ-48/2.5-D24
UVQ-24/4.5-D24
UVQ-18/5.6-D24
UVQ-15/7-D24
UVQ-12/8-D24
UVQ-5/20-D24
UVQ-3.3/30-D24
UVQ-2.5/35-D24
UVQ-1.5/40-D24
Typical @ TA = +25°C under nominal line voltage, nominal output voltage, natural air convection, external caps and full-load conditions, unless noted. (1)
Dynamic characteristics
Dynamic load response
(50-75-50% load step)
Start-up time
VIN to VOUT regulated, mSec
Remote On/Off to VOUT
regulated, mSec
Switching frequency, (KHz)
100 μSec to
±1%
of final value
90msec
150 μSec to 150 μSec to 100 μSec to
50 μSec
40 μSec to 50 μSec to 100 μSec
100 μSec
±1.5%
±1.5% ±1.5% of final to ±1%
±1.25%
±1%
to ±1%
to ±1%
of final value of final value
value
of final value of final value of final value of final value of final value
50msec
50msec
200msec
40msec
30msec
90msec
50msec
50msec
380 ± 30
500 to 650
600
30msec
290msec
100msec
200msec
30msec
25msec
35msec
200msec
100msec
360
290 ± 30
242
240 ± 25
290 ± 30
250 ± 25
Environmental
Calculated MTBF4
TBD
Operating temperature
range: see Derating
Curves.
−40 to +85°C (with Derating, see Note 15.)
Operating temperature,
with baseplate, no
derating required (°C)3
−40 to +110
Storage temperature (°C)
−40 to +115
−40 to +110
−55 to +130
−55 to +125
Thermal protection/
shutdown
+110 to 125°C, model dependent
Relative humidity
To +85°C/85%, non-condensing
Physical
Outline dimensions
See mechanical specs.
Baseplate material
Aluminum
Pin material
Brass alloy
Pin diameter
Weight
Electromagnetic
interference
(conducted and
radiated)
(external filter required)
Safety
0.04/0.062 inches (1.016/1.524 mm)
1.55 ounce
(44 grams)
1 ounce (28 grams)
Designed to meet FCC part 15, class B, EN55022
Designed to meet UL/cUL 60950-1, CSA C22.2 No.60950-1, IEC/EN 60950-1
www.murata-ps.com
Technical enquiries email: [email protected], tel: +1 508 339 3000
MDC_UVQ Models.B11 Page 6 of 25
UVQ Series
Low Profile, Isolated Quarter Brick
2.5–40 Amp DC/DC Converters
Performance/Functional Specifications 48V Models
UVQ-48/2.5-D48
UVQ-24/4.5-D48
UVQ-18/6-D48
UVQ-15/7-D48
UVQ-12/10-D48
UVQ-5/20-D48
UVQ-3.3/35-D48
UVQ-2.5/40-D48
Typical @ TA = +25°C under nominal line voltage, nominal output voltage, natural air convection, external caps and full-load conditions, unless noted. (1)
Input
Input voltage range
See ordering guide
Start-up threshold, min (V)
35
Undervoltage
shutdown, (V)14
34.5
34
33.5
34.5
35
32
Overvoltage shutdown (V)
33.5
none
Reflected (back) ripple
current
10-50 mA pk-pk, model dependent
Input Current
Full load conditions
Inrush transient, (A2sec)
See ordering guide.
0.05
0.05
No load, mA
100
Low line (VIN = min.),
(Amps)
3.15
Output short circuit, (mA)
1
1
10
130
80
60
3.56
3.07
3.72
3.21
50
Standby mode,
(Off, UV, OT shutdown)
Internal input filter type
0.05
1
0.05
0.05
30
50
250
50
30
80
45
30
3.35
3.30
3.60
1-4mA, model dependent
L-C
Pi-type
Reverse polarity
protection
L-C
See notes.
Remote On/Off Control5
Positive logic, "P" suffix
(specifications are max)
OFF = Ground pin to +0.8V
ON = Open or +5V to +VIN max
Negative logic, "N" suffix
(specifications are max)
OFF = Open or +5V to +VIN max
ON = Ground pin to+0.8V max
Current
1-8 mA, model dependent
www.murata-ps.com
Technical enquiries email: [email protected], tel: +1 508 339 3000
MDC_UVQ Models.B11 Page 7 of 25
UVQ Series
Low Profile, Isolated Quarter Brick
2.5–40 Amp DC/DC Converters
Performance/Functional Specifications 48V Models
UVQ-48/2.5-D48
UVQ-24/4.5-D48
UVQ-18/6-D48
UVQ-15/7-D48
UVQ-12/10-D48
UVQ-5/20-D48
UVQ-3.3/35-D48
UVQ-2.5/40-D48
Typical @ TA = +25°C under nominal line voltage, nominal output voltage, natural air convection, external caps and full-load conditions, unless noted. (1)
Output
Voltage output range
See ordering guide.
Voltage output accuracy
(50% load)
±1.5% of VNOM
±1.25% of VNOM
Adjustment range
–20 to +10% of VNOM.
±0.02% of VOUT range per °C
Temperature coefficient
Minimum loading
±1% of VNOM
No minimum
load
3 Amps
No minimum
load
No minimum load
Remote sense
compensation
+10%.
Ripple/noise
See ordering guide.
Line/Load regulation
See ordering guide.
Efficiency
See ordering guide.
Maximum capacitive
loading, Low ESR
<0.02Ω max.,
resistive load, (μF)
Current limit inception
(98% of VOUT, after
warmup), (Amps)
10,000
46
4700
48
Short circuit protection
method
26
8.5
7
1000
6.5
3.3
3
3.5
29 Volts max
55 Volts max
Current limiting, hiccup autorestart. Remove overload for recovery.
Short circuit current,
(Amps)
5
0.1
Short circuit duration
Overvoltage protection, (via
magnetic feedback)
12.5
2200
1.5
3
3
Output may be shorted continuously to ground (no damage).
3 Volts max
4 Volts max
6 Volts max
14.4 Volts max 18.5 Volts max
22 Volts max
Isolation Characteristics
Isolation Voltage
Input to Output, (Volts min)
2250
Input to baseplate
1500
Baseplate to output,
(Volts min)
1500
1500
Isolation resistance
Isolation capacitance, (pF)
100 MΩ
1500
Isolation safety rating
1000
50
50
1500
Basic insulation
www.murata-ps.com
Technical enquiries email: [email protected], tel: +1 508 339 3000
MDC_UVQ Models.B11 Page 8 of 25
UVQ Series
Low Profile, Isolated Quarter Brick
2.5–40 Amp DC/DC Converters
Performance/Functional Specifications 48V Models
50msec
50msec
50msec
50msec
30msec
30msec
30msec
100msec
50msec
600
600
450 ± 50
290 ± 30
245 ± 20
240 ± 25
290 ± 30
540 ± 40
−40 to +110
−40 to +120
UVQ-15/7-D48
UVQ-48/2.5-D48
50msec
UVQ-5/20-D48
UVQ-24/4.5-D48
150 μSec to
±1.5%
of final value
UVQ-18/6-D48
UVQ-3.3/35-D48
150 μSec to
±1.5%
of final value
UVQ-12/10-D48
UVQ-2.5/40-D48
Typical @ TA = +25°C under nominal line voltage, nominal output voltage, natural air convection, external caps and full-load conditions, unless noted. (1)
Dynamic characteristics
Dynamic load response
(50-75-50% load step)
Start-up time
VIN to VOUT regulated, mSec
Remote On/Off to VOUT
regulated, mSec
Switching frequency, (KHz)
90 μSec
100 μSec
50 μSec to ±1% 50 μSec to ±1% 50 μSec to ±1%
to ±2%
to ±1%
of final value of final value of final value
of final value
of final value
50msec
40msec
30msec
30msec
100msec
75 μSec
to ±1%
of final value
50msec
Environmental
Calculated MTBF4
TBD
Operating temperature
range: see Derating
Curves.
Operating temperature,
with baseplate, no
derating required (°C)3
−40 to +85°C (with Derating, see Note 15.)
−40 to +110
−40 to +115
Storage temperature (°C)
−40 to +110
−55 to +125
Thermal protection/
shutdown
+110 to 125°C, model dependent
Relative humidity
To +85°C/85%, non-condensing
Physical
Outline dimensions
See mechanical specs.
Baseplate material
Aluminum
Pin material
Brass alloy
Pin diameter
0.04/0.062 inches (1.016/1.524 mm)
Weight
Electromagnetic
interference
(conducted and
radiated)
(external filter required)
Safety
1 ounce (28 grams)
Designed to meet FCC part 15, class B, EN55022
Designed to meet UL/cUL 60950-1, CSA C22.2 No.60950-1, IEC/EN 60950-1
www.murata-ps.com
Technical enquiries email: [email protected], tel: +1 508 339 3000
MDC_UVQ Models.B11 Page 9 of 25
UVQ Series
Low Profile, Isolated Quarter Brick
2.5–40 Amp DC/DC Converters
PART NUMBER STRUCTURE
Input Voltage
Continuous
Transient (100 mS)
24V models
0 to +36V
+50V
48V models
0 to +75V
+100V
On/Off Control
–0.3 V min to +13.5V max.
Input Reverse Polarity Protection
See Fuse section
Output Overvoltage
VOUT +20% max.
Output Current (Note 7)
Current-limited. Devices can withstand
sustained short circuit without damage.
Storage Temperature
–55 to +125°C
Lead Temperature
See soldering guidelines
Absolute maximums are stress ratings. Exposure of devices to greater than
any of these conditions may adversely affect long-term reliability. Proper
operation under conditions other than those listed in the Performance/Functional Specifications Table is not implied nor recommended.
(1) All models are tested and specified with 200 LFM airflow, external 1||10μF ceramic/
tantalum output capacitors. External input capacitance varies according to model type.
All capacitors are low ESR types. These capacitors are necessary to accommodate
our test equipment and may not be required to achieve specified performance in your
applications. All models are stable and regulate within spec under no-load conditions.
General conditions for Specifications are +25°C, VIN =nominal, VOUT = nominal, full load.
(2) Input Ripple Current is tested and specified over a 5-20MHz bandwidth. Input filtering is CIN = 33μF tantalum, CBUS = 220μF electrolytic, LBUS = 12μH.
(3) Note that Maximum Power Derating curves indicate an average current at nominal
input voltage. At higher temperatures and/or lower airflow, the DC/DC converter will
tolerate brief full current outputs if the total RMS current over time does not exceed
the Derating curve.
(4) Mean Time Before Failure is calculated using the Telcordia (Belcore) SR-332 Method 1,
Case 3, ground fixed conditions, TPCBOARD = +25°C, full output load, natural air
convection.
(5) The On/Off Control may be driven with external logic or by applying appropriate
external voltages which are referenced to Input Common. The On/Off Control Input
should use either an open collector/open drain transistor or logic gate which does
not exceed +13.5V.
(6) Short circuit shutdown begins when the output voltage degrades approximately 2%
from the selected setting.
(7) The outputs are not intended to sink appreciable reverse current.
(8) Output noise may be further reduced by adding an external filter. See I/O Filtering
and Noise Reduction.
(9) All models are fully operational and meet published specifications, including “cold
start” at –40°C.
(10) Regulation specifications describe the deviation as the line input voltage or output
load current is varied from a nominal midpoint value to either extreme.
(11) Overvoltage shutdown on 48V input models is not supplied in order to comply with
telecom reliability requirements. These requirements attempt continued operation
despite significant input overvoltage.
(12) Do not exceed maximum power specifications when adjusting the output trim.
(13) Note that the converter may operate up to +110°C with the baseplate installed.
However, thermal self-protection occurs near +110°C, and there is a temperature
gradient between the hotspot and the baseplate. Therefore, +100°C is recommended to avoid thermal shutdown.
(14) The converter is guaranteed to turn off at the UV shutdown voltage.
(15) At full power, the package temperature of all on-board components must not exceed
+128°C.
www.murata-ps.com
MECHANICAL SPECIFICATIONS
Removal of Soldered UVQ's from Printed Circuit Boards
Should removal of the UVQ from its soldered connection be needed, thoroughly
de-solder the pins using solder wicks or de-soldering tools. At no time should
any prying or leverage be used to remove boards that have not been properly
de-soldered first.
Input Source Impedance
UVQ converters must be driven from a low ac-impedance input source. The
DC/DC’s performance and stability can be compromised by the use of highly
inductive source impedances. The input circuit shown in Figure 2 is a practical
solution that can be used to minimize the effects of inductance in the input
traces. For optimum performance, components should be mounted close to
the DC/DC converter.
I/O Filtering, Input Ripple Current, and Output Noise
All models in the UVQ Series are tested/specified for input ripple current (also
called input reflected ripple current) and output noise using the circuits and
layout shown in Figures 2 and 3.
TO
OSCILLOSCOPE
3
+INPUT
LBUS
+
VIN
CURRENT
PROBE
CBUS
CIN
–
1
–INPUT
CIN = 33μF, ESR < 700mΩ @ 100kHz
CBUS = 220μF, ESR < 100mΩ @ 100kHz
LBUS = 12μH
Figure 2. Measuring Input Ripple Current
External input capacitors (CIN in Figure 2) serve primarily as energy-storage
elements. They should be selected for bulk capacitance (at appropriate frequencies), low ESR, and high rms-ripple-current ratings. The switching nature
of DC/DC converters requires that dc voltage sources have low ac impedance
as highly inductive source impedance can affect system stability. In Figure 2,
CBUS and LBUS simulate a typical dc voltage bus. Your specific system configuration may necessitate additional considerations.
Technical enquiries email: [email protected], tel: +1 508 339 3000
MDC_UVQ Models.B11 Page 10 of 25
UVQ Series
Low Profile, Isolated Quarter Brick
2.5–40 Amp DC/DC Converters
In critical applications, output ripple/noise (also referred to as periodic and
random deviations or PARD) can be reduced below specified limits using filtering techniques, the simplest of which is the installation of additional external
output capacitors. Output capacitors function as true filter elements and
should be selected for bulk capacitance, low ESR, and appropriate frequency
response. In Figure 3, the two copper strips simulate real-world pcb impedances between the power supply and its load. Scope measurements should be
made using BNC connectors or the probe ground should be less than ½ inch
and soldered directly to the fixture.
All external capacitors should have appropriate voltage ratings and be
located as close to the converter as possible. Temperature variations for all
relevant parameters should be taken into consideration. OS-CONTM organic
semiconductor capacitors (www.sanyo.com) can be especially effective for
further reduction of ripple/noise. The most effective combination of external I/O
capacitors will be a function of line voltage and source impedance, as well as
particular load and layout conditions.
On/Off Control
The primary-side, Remote On/Off Control function (pin 2) can be specified
to operate with either positive or negative polarity. Positive-polarity devices
("P" suffix) are enabled when pin 2 is left open or is pulled high. Positivepolarity devices are disabled when pin 2 is pulled low (0-0.8V with respect to
–Input). Negative-polarity devices are off when pin 2 is high/open and on when
pin 2 is pulled low. See Figure 4.
Dynamic control of the remote on/off function is best accomplished with a
mechanical relay or an open-collector/open-drain drive circuit (optically isolated if appropriate). The drive circuit should be able to sink appropriate current
(see Performance Specifications) when activated and withstand appropriate
voltage when deactivated.
).054
%15)6!,%.4#)2#5)4&/2
0/3)4)6%!.$.%'!4)6%
,/')#-/$%,3
6
/./&&
#/.42/,
+SENSE
+OUTPUT
7
#/.42/,
COPPER STRIP
8
2%&
C1
C2
SCOPE
n).054
#/--/.
RLOAD
Figure 4. Driving the Remote On/Off Control Pin
4
–OUTPUT
5
–SENSE
COPPER STRIP
C1 = 1μF CERAMIC
C2 = 10μF TANTALUM
LOAD 2-3 INCHES (51-76mm) FROM MODULE
Figure 3. Measuring Output Ripple/Noise (PARD)
Start-Up Threshold and Undervoltage Shutdown
Under normal start-up conditions, the UVQ Series will not begin to regulate
properly until the ramping input voltage exceeds the Start-Up Threshold.
Once operating, devices will turn off when the applied voltage drops below
the Undervoltage Shutdown point. Devices will remain off as long as the
undervoltage condition continues. Units will automatically re-start when the
applied voltage is brought back above the Start-Up Threshold. The hysteresis
built into this function avoids an indeterminate on/off condition at a single input
voltage. See Performance/Functional Specifications table for actual limits.
Start-Up Time
The VIN to VOUT Start-Up Time is the interval between the point at which a
ramping input voltage crosses the Start-Up Threshold voltage and the point at
which the fully loaded output voltage enters and remains within its specified
r1% accuracy band. Actual measured times will vary with input source impedance, external input capacitance, and the slew rate and final value of the input
voltage as it appears to the converter. The On/Off to VOUT start-up time assumes
that the converter is turned off via the Remote On/Off Control with the nominal
input voltage already applied.
www.murata-ps.com
Current Limiting
When power demands from the output falls within the current limit inception
range for the rated output current, the DC/DC converter will go into a current
limiting mode. In this condition the output voltage will decrease proportionately
with increases in output current, thereby maintaining a somewhat constant
power dissipation. This is commonly referred to as power limiting. Current
limit inception is defined as the point where the full-power output voltage
falls below the specified tolerance. If the load current being drawn from the
converter is significant enough, the unit will go into a short circuit condition.
See “Short Circuit Condition.”
Short Circuit Condition
When a converter is in current limit mode the output voltages will drop as
the output current demand increases. If the output voltage drops too low, the
magnetically coupled voltage used to develop primary side voltages will also
drop, thereby shutting down the PWM controller. Following a time-out period
of about 50 milliseconds, the PWM will restart, causing the output voltages to
begin ramping to their appropriate values. If the short-circuit condition persists,
another shutdown cycle will be initiated. This on/off cycling is referred to as
“hiccup” mode. The hiccup cycling reduces the average output current, thereby
preventing internal temperatures from rising to excessive levels. The UVQ is
capable of enduring an indefinite short circuit output condition.
Technical enquiries email: [email protected], tel: +1 508 339 3000
MDC_UVQ Models.B11 Page 11 of 25
UVQ Series
Low Profile, Isolated Quarter Brick
2.5–40 Amp DC/DC Converters
Thermal Shutdown
UVQ converters are equipped with thermal-shutdown circuitry. If the internal temperature of the DC/DC converter rises above the designed operating
temperature (See Performance Specifications), a precision temperature sensor
will power down the unit. When the internal temperature decreases below the
threshold of the temperature sensor, the unit will self start.
Output Overvoltage Protection
The output voltage is monitored for an overvoltage condition via magnetic coupling to the primary side. If the output voltage rises to a fault condition, which
could be damaging to the load circuitry (see Performance Specifications), the
sensing circuitry will power down the PWM controller causing the output voltage to decrease. Following a time-out period the PWM will restart, causing the
output voltage to ramp to its appropriate value. If the fault condition persists,
and the output voltages again climb to excessive levels, the overvoltage
circuitry will initiate another shutdown cycle. This on/off cycling is referred to
as "hiccup" mode.
Input Reverse-Polarity Protection
If the input-voltage polarity is accidentally reversed, an internal diode will
become forward biased and likely draw excessive current from the power
source. If the source is not current limited or the circuit appropriately fused, it
could cause permanent damage to the converter.
Input Fusing
Certain applications and/or safety agencies may require the installation of
fuses at the inputs of power conversion components. Fuses should also be
used if the possibility of a sustained, non-current-limited, input-voltage polarity
reversal exists. For MPS UVQ Series DC/DC Converters, slow-blow fuses are
recommended with values no greater than twice the maximum input current.
Trimming Output Voltage
UVQ converters have a trim capability (pin 6) that enables users to adjust the
output voltage from +10% to –20% (refer to the trim equations). Adjustments
to the output voltage can be accomplished with a single fixed resistor as shown
in Figures 5 and 6. A single fixed resistor can increase or decrease the output
voltage depending on its connection. Resistors should be located close to
the converter and have TCR's less than 100ppm/°C to minimize sensitivity to
changes in temperature. If the trim function is not used, leave the trim pin open.
1
–INPUT
+OUTPUT
+SENSE
2
ON/OFF
CONTROL
TRIM
3
+INPUT
–OUTPUT
–INPUT
+OUTPUT
+SENSE
2
ON/OFF
CONTROL
TRIM
+INPUT
7
6
LOAD
RTRIM DOWN
–SENSE
3
8
–OUTPUT
5
4
Figure 6. Trim Connections To Decrease Output Voltages Using Fixed Resistors
Standard UVQ's have a "positive trim" where a single resistor connected
from the Trim pin (pin 6) to the +Sense (pin 7) will increase the output voltage. A
resistor connected from the Trim Pin (pin 6) to the –Sense (pin 5) will decrease
the output voltage.
Trim adjustments greater than the specified +10%/–20% can have an
adverse affect on the converter’s performance and are not recommended.
Excessive voltage differences between VOUT and Sense, in conjunction with trim
adjustment of the output voltage, can cause the overvoltage protection circuitry
to activate (see Performance Specifications for overvoltage limits).
Temperature/power derating is based on maximum output current and
voltage at the converter's output pins. Use of the trim and sense functions can
cause output voltages to increase, thereby increasing output power beyond
the UVQ's specified rating, or cause output voltages to climb into the output
overvoltage region. Therefore:
(VOUT at pins) x (IOUT) d rated output power
The Trim pin (pin 6) is a relatively high impedance node that can be susceptible to noise pickup when connected to long conductors in noisy environments.
Soldering Guidelines
Murata Power Solutions recommends the specifications below when installing these
converters. These specifications vary depending on the solder type. Exceeding these
specifications may cause damage to the product. Be cautious when there is high atmospheric humidity. We strongly recommend a mild pre-bake (100° C. for 30 minutes). Your
production environment may differ; therefore please thoroughly review these guidelines
with your process engineers.
8
7
6
LOAD
RTRIM UP
–SENSE
1
Wave Solder Operations for through-hole mounted products (THMT)
For Sn/Ag/Cu based solders:
5
Maximum Preheat Temperature
4
115° C.
Maximum Pot Temperature
270° C.
Maximum Solder Dwell Time
7 seconds
For Sn/Pb based solders:
Figure 5. Trim Connections To Increase Output Voltages Using Fixed Resistors
www.murata-ps.com
Maximum Preheat Temperature
105° C.
Maximum Pot Temperature
250° C.
Maximum Solder Dwell Time
6 seconds
Technical enquiries email: [email protected], tel: +1 508 339 3000
MDC_UVQ Models.B11 Page 12 of 25
UVQ Series
Low Profile, Isolated Quarter Brick
2.5–40 Amp DC/DC Converters
Trim Equations
F E AT U R E S A N D O P T I O N S
Trim Up
Trim Down
Remote Sense
UVQ-1.5/40-D24
RT UP (k:) =
6.23(VO – 1.226)
–10.2
VO – 1.5
RTDOWN (k:) =
7.64
1.5 – VO
–10.2
UVQ-2.5/40-D48, UVQ-2.5/35-D24
RT UP (k:) =
10(VO – 1.226)
–10.2
VO – 2.5
RTDOWN (k:) =
12.26
2.5 – VO
–10.2
UVQ-3.3/35-D48
RT UP (k:) =
13.3(VO – 1.226)
VO – 3.3
–10.2
RTDOWN (k:) =
16.31
3.3 – VO
–10.2
UVQ-5/25-D24, UVQ-5/20-D48
RT UP (k:) =
20.4(VO – 1.226)
VO – 5
–10.2
RTDOWN (k:) =
25.01
5 – VO
–10.2
Note: The Sense and VOUT lines are internally connected through lowvalue resistors. Nevertheless, if the sense function is not used for remote
regulation the user must connect the +Sense to +VOUT and -Sense to –VOUT
at the DC/DC converter pins.
UVQ series converters employ a sense feature to provide point of use
regulation, thereby overcoming moderate IR drops in pcb conductors or
cabling. The remote sense lines carry very little current and therefore
require minimal cross-sectional-area conductors. The sense lines, which
are capacitively coupled to their respective output lines, are used by the
feedback control-loop to regulate the output. As such, they are not low
impedance points and must be treated with care in layouts and cabling.
Sense lines on a pcb should be run adjacent to dc signals, preferably
ground. In cables and discrete wiring applications, twisted pair or other
techniques should be implemented.
UVQ series converters will compensate for drops between the output
voltage at the DC/DC and the sense voltage at the DC/DC provided that:
UVQ-12/8-D24, -12/10-D48
RT UP (k:) =
49.6(VO – 1.226)
VO – 12
–10.2
RTDOWN (k:) =
[VOUT(+) –VOUT(–)] – [Sense(+) –Sense (–)] ≤ 10% VOUT
60.45
12 – VO
Contact and PCB resistance
losses due to IR drops
–10.2
1
–INPUT
UVQ-15/7-D24, -D48
RT UP (k:) =
62.9(VO – 1.226)
VO – 15
–10.2
RTDOWN (k:) =
+OUTPUT
+SENSE
76.56
15 – VO
–10.2
8
7
IOUT
Sense Current
2
ON/OFF
CONTROL
TRIM
6
LOAD
Sense Return
UVQ-18/5.6-D24, -18/6-D48
–SENSE
5
IOUT Return
RT UP (k:) =
75.5(VO – 1.226)
VO – 18
–10.2
RTDOWN (k:) =
92.9
18 – VO
3
–10.2
101(VO – 1.226)
VO – 24
–10.2
RTDOWN (k:) =
210.75(VO – 1.226)
VO – 48
–10.2
RTDOWN (k:) =
4
Figure 8. Remote Sense Circuit Configuration
124.2
24 – VO
–10.2
UVQ-48/2.5-D24, -D48
RT UP (k:) =
–OUTPUT
Contact and PCB resistance
losses due to IR drops
UVQ-24/4.5-D24, -D48
RT UP (k:) =
+INPUT
250
48 – VO
–10.2
Note: Higher output 24V and 48V converters require larger, low-tempco,
precision trim resistors. An alternative is a low-TC multi-turn potentiometer
(20kΩ typical) connected between +VOUT and –VOUT with the wiper to the Trim
pin.
www.murata-ps.com
Output overvoltage protection is monitored at the output voltage pin, not
the Sense pin. Therefore, excessive voltage differences between VOUT and
Sense in conjunction with trim adjustment of the output voltage can cause
the overvoltage protection circuitry to activate (see Performance Specifications for overvoltage limits). Power derating is based on maximum output
current and voltage at the converter's output pins. Use of trim and sense
functions can cause output voltages to increase, thereby increasing output
power beyond the conveter's specified rating, or cause output voltages
to climb into the output overvoltage region. Therefore, the designer must
ensure:
(VOUT at pins) × (IOUT) ≤ rated output power
Technical enquiries email: [email protected], tel: +1 508 339 3000
MDC_UVQ Models.B11 Page 13 of 25
UVQ Series
Low Profile, Isolated Quarter Brick
2.5–40 Amp DC/DC Converters
UVQ-1.5/40-D24N: Maximum Current Temperature Derating
(No baseplate, V IN = 24V, transverse air flow)
UVQ-1.5/40-D24N: Maximum Current Temperature Derating
(With baseplate, V IN = 24V, transverse air flow)
40
40
39
Output Current (Amps)
Output Current (Amps)
39
Natural convection
38
100 lfm
37
200 lfm
200 lfm
36
400 lfm
35
34
Natural convection
38
37
100 lfm
36
400 lfm
35
34
33
33
20
25
30
35
40
45
50
55
60
65
70
75
80
85
20
25
30
35
40
Ambient Temperature ( oC)
50
55
60
65
70
75
80
85
UVQ-2.5/40-D48
Power Dissipation vs. Load Current @ 25°C
UVQ-2.5/40-D48N
Efficiency vs. Line Voltage and Load Current @ 25°C
16
92
14
Power Dissipation (Watts)
88
84
80
Efficiency (%)
45
Ambient Temperature (oC)
76
VIN = 36V
72
VIN = 48V
68
12
VIN = 48V
10
8
6
4
VIN = 75V
2
64
0
62
0
5
10
15
20
25
30
35
0
40
5
10
15
20
25
30
35
40
Load Current (Amps)
Load Current (Amps)
UVQ-3.3/30-D24N: Maximum Current Temperature Derating
(With baseplate, V IN = 24V, transverse air flow at sea level)
UVQ-3.3/30-D24N: Maximum Current Temperature Derating
(No baseplate, V IN = 24V, transverse air flow at sea level)
30
30
29
29
27
Output Current (Amps)
Output Current (Amps)
28
Natural convection
26
25
100 lfm
24
200 lfm
23
300 lfm
22
21
28
Natural convection
27
100 lfm
26
200 lfm
25
300 lfm
24
400 lfm
400 lfm
20
23
19
22
18
17
21
20
25
30
35
40
45
50
55
60
65
70
75
80
85
Ambient Temperature ( oC)
www.murata-ps.com
20
25
30
35
40
45
50
55
60
65
70
75
80
85
Ambient Temperature (oC)
Technical enquiries email: [email protected], tel: +1 508 339 3000
MDC_UVQ Models.B11 Page 14 of 25
UVQ Series
Low Profile, Isolated Quarter Brick
2.5–40 Amp DC/DC Converters
UVQ-3.3/35-D48 Maximum Current Temperature Derating
(With baseplate, V IN = 48V, transverse air flow at sea level)
36
Output Current (Amps)
34
32
30
28
Natural Convection
26
100 lfm
24
200 lfm
22
300 lfm
20
400 lfm
18
20
25
30
35
40
45
50
55
60
65
70
75
80
85
Ambient Temperature ( oC)
UVQ-5/20-D24P: Maximum Current Temperature Derating
(No baseplate, VIN = 24V, transverse air flow)
UVQ-5/20-D24PB: Maximum Current Temperature Derating
(With baseplate, VIN = 24V, transverse air flow)
20
20
19.5
19.5
Output Current (Amps)
Output Current (Amps)
19
18.5
18
17.5
17
Natural convection
100 lfm
200 lfm
300 lfm
400 lfm
16.5
16
15.5
19
18.5
Natural convection
100 lfm
200 lfm
300 lfm
400 lfm
18
17.5
17
16.5
15
16
14.5
14
15.5
20
25
30
35
40
45
50
55
60
65
70
75
80
20
85
25
30
35
40
Ambient Temperature (oC)
50
55
60
65
70
75
80
85
Ambient Temperature (oC)
UVQ-5/20-D24P
Efficiency vs. Line Voltage and Load Current @ +25°C
UVQ-5/20-D24
Power Dissipation vs. Load Current @ +25°C
94
10
93
9
Power Dissipation (Watts)
92
91
Efficiency (%)
45
VIN = 18V
90
VIN = 24V
89
88
VIN = 30V
87
VIN = 36V
8
7
6
5
4
VIN = 18V
VIN = 24V
3
86
VIN = 30V
2
85
VIN = 36V
1
84
5
6.5
8
9.5
11
12.5
14
15.5
17
18.5
20
Load Current (Amps)
www.murata-ps.com
5
6.5
8
9.5
11
12.5
14
15.5
17
18.5
20
Load Current (Amps)
Technical enquiries email: [email protected], tel: +1 508 339 3000
MDC_UVQ Models.B11 Page 15 of 25
UVQ Series
Low Profile, Isolated Quarter Brick
2.5–40 Amp DC/DC Converters
UVQ-5/20-D48
Efficiency vs. Line Voltage and Load Current @ 25°C
UVQ-5/20-D48P: Maximum Current Temperature Derating
(No baseplate, V IN = 48V, transverse air flow at sea level)
92
21
88
20
Output Current (Amps)
Efficiency (%)
84
80
76
VIN = 36V
72
VIN = 48V
19
18
100 lfm
17
200 lfm
16
300 lfm
15
400 lfm
14
68
Natural convection
VIN = 75V
13
64
12
20
25
30
35
40
45
50
55
60
65
70
75
80
85
62
0
2
4
6
8
10
12
14
16
18
20
Ambient Temperature (oC)
Load Current (Amps)
UVQ-5/20-D48PB: Maximum Current Temperature Derating
(With baseplate, V IN = 48V, transverse air flow at sea level)
21
Output Current (Amps)
20
19
18
100 lfm
17
200 lfm
16
300 lfm
15
400 lfm
14
13
20
25
30
35
40
45
50
55
60
65
70
75
80
85
Ambient Temperature ( oC)
www.murata-ps.com
Technical enquiries email: [email protected], tel: +1 508 339 3000
MDC_UVQ Models.B11 Page 16 of 25
UVQ Series
Low Profile, Isolated Quarter Brick
2.5–40 Amp DC/DC Converters
UVQ-12/8-D24P
Efficiency vs. Line Voltage and Load Current @ +25°C
UVQ-12/8-D24P: Maximum Current Temperature Derating
(No baseplate, VIN = 24V, transverse air flow)
95
7.8
90
7.6
7.4
Efficiency (%)
Output Current (Amps)
8.0
100 lfm
200 lfm
300 lfm
7.2
VIN = 18V
85
VIN = 24V
VIN = 30V
7.0
80
VIN = 36V
6.8
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
Ambient Temperature (oC)
75
0.8
1.6
2.4
3.2
4
4.8
5.6
6.4
7.2
8
Load Current (Amps)
UVQ-12/10-D48N: Maximum Current Temperature Derating
(No baseplate, VIN = 48V, transverse air flow)
UVQ-12/10-D48N: Maximum Current Temperature Derating
(With baseplate, VIN = 48V, transverse air flow)
10
10.0
Output Current (Amps)
Output Current (Amps)
9.5
9
8
7
Natural convection
100 lfm
200 lfm
300 lfm
400 lfm
6
9.0
8.5
8.0
7.5
Natural convection
100 lfm
200 lfm
300 lfm
400 lfm
7.0
6.5
6.0
5
20
25
30
35
40
45
50
55
60
65
70
75
80
20
85
25
30
35
40
Ambient Temperature (oC)
45
50
55
60
65
70
75
80
85
Ambient Temperature (oC)
UVQ-12/10-D48N
Efficiency vs. Line Voltage and Load Current @ +25°C
UVQ-12/10-D48N
Power Dissipation vs. Load Current @ +25°C
15
92
13
88
VIN = 36V
86
VIN = 48V
Power Dissipation (Watts)
Efficiency (%)
90
VIN = 60V
84
VIN = 75V
82
11
VIN = 75V
9
VIN = 60V
VIN = 48V
7
VIN = 36V
5
3
80
1
78
1
2
3
4
5
6
7
8
9
10
Load Current (Amps)
www.murata-ps.com
1
2
3
4
5
6
7
8
9
10
Load Current (Amps)
Technical enquiries email: [email protected], tel: +1 508 339 3000
MDC_UVQ Models.B11 Page 17 of 25
UVQ Series
Low Profile, Isolated Quarter Brick
2.5–40 Amp DC/DC Converters
UVQ-15/7-D24N: Maximum Current Temperature Derating
(With baseplate, VIN = 24V, transverse air flow)
7.5
7.5
7
7
Output Current (Amps)
Output Current (Amps)
UVQ-15/7-D24N: Maximum Current Temperature Derating
(No baseplate, VIN = 24V, transverse air flow)
6.5
6
5.5
Natural convection
100 lfm
200 lfm
300 lfm
400 lfm
5
4.5
6.5
6
Natural convection
100 lfm
200 lfm
300 lfm
400 lfm
5.5
5
4.5
4
4
20
25
30
35
40
45
50
55
60
65
70
75
80
85
20
90
25
30
35
40
45
Ambient Temperature (oC)
UVQ-15/7-D24N
Efficiency vs. Line Voltage and Load Current @ +25°C
92
11
Power Dissipation (Watts)
13
Efficiency (%)
90
VIN = 18V
VIN = 24V
86
VIN = 30V
84
55
60
65
70
75
80
85
90
UVQ-15/7-D24N
Power Dissipation vs. Load Current @ +25°C
94
88
50
Ambient Temperature (oC)
VIN = 36V
9
VIN = 36V
VIN = 30V
7
VIN = 24V
VIN = 18V
5
3
82
1
80
0.7
1.4
2.1
2.8
3.5
4.2
4.9
5.6
6.3
7
Load Current (Amps)
www.murata-ps.com
0.7
1.4
2.1
2.8
3.5
4.2
4.9
5.6
6.3
7
Load Current (Amps)
Technical enquiries email: [email protected], tel: +1 508 339 3000
MDC_UVQ Models.B11 Page 18 of 25
UVQ Series
Low Profile, Isolated Quarter Brick
2.5–40 Amp DC/DC Converters
7.0
6.8
6.6
6.4
6.2
6.0
5.8
5.6
5.4
5.2
5.0
4.8
4.6
4.4
4.2
4.0
UVQ-15/7-D48N: Maximum Current Temperature Derating
(With baseplate, VIN = 48V, transverse air flow)
Output Current (Amps)
Output Current (Amps)
UVQ-15/7-D48N: Maximum Current Temperature Derating
(No baseplate, VIN = 48V, transverse air flow)
Natural convection
100 lfm
200 lfm
300 lfm
400 lfm
20
25
30
35
40
45
50
55
60
65
70
75
80
85
7.0
6.8
6.6
6.4
6.2
6.0
5.8
5.6
5.4
5.2
5.0
4.8
4.6
4.4
4.2
4.0
Natural convection
100 lfm
200 lfm
300 lfm
20
90
25
30
35
40
45
Ambient Temperature (oC)
UVQ-15/7-D48N
Efficiency vs. Line Voltage and Load Current @ +25°C
11
92
10
60
65
70
75
80
85
90
9
Power Dissipation (Watts)
90
88
Efficiency (%)
55
UVQ-15/7-D48N
Power Dissipation vs. Load Current @ +25°C
94
86
VIN = 36V
84
VIN = 48V
82
VIN = 60V
80
8
VIN = 75V
VIN = 60V
7
VIN = 48V
6
VIN = 36V
5
4
3
VIN = 75V
2
78
76
0.7
50
Ambient Temperature (oC)
1
1.4
2.1
2.8
3.5
4.2
4.9
5.6
6.3
7
Load Current (Amps)
www.murata-ps.com
0.7
1.4
2.1
2.8
3.5
4.2
4.9
5.6
6.3
7
Load Current (Amps)
Technical enquiries email: [email protected], tel: +1 508 339 3000
MDC_UVQ Models.B11 Page 19 of 25
UVQ Series
Low Profile, Isolated Quarter Brick
2.5–40 Amp DC/DC Converters
UVQ-18/5.6-D24
Efficiency vs. Line Voltage and Load Current @ 25°C
92
90
Efficiency (%)
88
86
84
VIN = 18V
82
VIN = 24V
80
VIN = 36V
78
76
0.56
1.12
1.68
2.24
2.8
3.36
3.92
4.48
5.04
5.6
Load Current (Amps)
UVQ-18/5.6-D24: Maximum Current Temperature Derating
(No baseplate, V IN = 24V, transverse air flow)
UVQ-18/5.6-D24: Maximum Current Temperature Derating
(With baseplate, V IN = 24V, transverse air flow)
5.8
5.8
5.6
5.6
200 lfm
5.2
Output Current (Amps)
Output Current (Amps)
5.4
300 lfm
5
4.8
400 lfm
100 lfm
4.6
4.4
4.2
4
Natural
Convection
3.8
5.4
5.2
5
Natural
Convection
4.8
100 lfm
200 lfm
4.6
300 lfm
400 lfm
4.4
4.2
3.6
4
3.4
20
25
30
35
40
45
50
55
60
65
70
75
80
20
85
25
30
35
Ambient Temperature ( oC)
45
50
55
60
65
70
75
80
85
Ambient Temperature (oC)
UVQ-18/6-D48
Power Dissipation vs. Load Current @ 25°C
UVQ-18/6-D48N
Efficiency vs. Line Voltage and Load Current @ 25°C
16
95
14
90
Power Dissipation (Watts)
VIN = 75V
85
Efficiency (%)
40
80
VIN = 36V
75
VIN = 48V
70
12
VIN = 48V
10
VIN = 36V
8
6
4
VIN = 75V
65
2
60
0.6
1.2
1.8
2.4
3
3.6
4.2
4.8
5.4
6
Load Current (Amps)
0
0.6
1.2
1.8
2.4
3
3.6
4.2
4.8
5.4
6
Load Current (Amps)
www.murata-ps.com
Technical enquiries email: [email protected], tel: +1 508 339 3000
MDC_UVQ Models.B11 Page 20 of 25
UVQ Series
Low Profile, Isolated Quarter Brick
2.5–40 Amp DC/DC Converters
UVQ-18/6-D48: Maximum Current Temperature Derating
(No baseplate, V IN = 48V, transverse air flow)
6.5
6.5
6
6
Output Current (Amps)
Output Current (Amps)
UVQ-18/6-D48: Maximum Current Temperature Derating
(With baseplate, V IN = 48V, transverse air flow)
5.5
100 lfm
5
200 lfm
4.5
300 lfm
5.5
5
100 lfm
200 lfm
4.5
300 lfm
500 lfm
4
4
3.5
500 lfm
3.5
20
25
30
35
40
45
50
55
60
65
70
75
80
85
20
25
30
35
40
Ambient Temperature ( oC)
45
50
55
60
65
70
75
80
85
85
90
Ambient Temperature ( oC)
UVQ-24/4.5-D24N
Efficiency vs. Line Voltage and Load Current @ +25°C
91
90
89
Efficiency (%)
88
87
86
VIN = 18V
85
VIN = 24V
84
VIN = 30V
83
VIN = 36V
82
81
80
1.00
1.35
1.70
2.05
2.40
2.75
3.10
3.45
3.80
4.15
4.50
Load Current (Amps)
UVQ-24/4.5-D48N
Efficiency vs. Line Voltage and Load Current @ +25°C
UVQ-24/4.5-D48N: Maximum Current Temperature Derating
(No baseplate, VIN = 48V, transverse air flow)
92
4.5
90
86
Output Current (Amps)
88
VIN = 36V
Efficiency (%)
84
VIN = 48V
82
80
VIN = 60V
78
76
VIN = 75V
4.3
400 lfm
300 lfm
200 lfm
100 lfm
4.0
3.8
3.5
74
3.3
72
70
3.0
68
20
66
64
1.00
25
30
35
40
45
50
55
60
65
70
75
80
Ambient Temperature (oC)
1.35
1.70
2.05
2.40
2.75
3.10
3.45
3.80
4.15
4.50
Load Current (Amps)
www.murata-ps.com
Technical enquiries email: [email protected], tel: +1 508 339 3000
MDC_UVQ Models.B11 Page 21 of 25
UVQ Series
Low Profile, Isolated Quarter Brick
2.5–40 Amp DC/DC Converters
UVQ-48/2.5-D48N
Efficiency vs. Line Voltage and Load Current @ 25°C
UVQ-48/2.5-D48N: Maximum Current Temperature Derating
(With baseplate, V IN = 48V, transverse air flow)
2.6
92
2.5
Output Current (Amps)
93
Efficiency (%)
91
90
VIN = 36V
89
VIN = 48V
2.4
Natural convection
2.3
100 lfm
2.2
200 lfm
88
VIN = 60V
2.1
87
VIN = 75V
2.0
86
20
25
30
35
40
45
50
55
60
65
70
75
80
85
Ambient Temperature (oC)
85
0.25
0.5
0.75
1
1.25
1.5
1.75
2
2.25
2.5
Load Current (Amps)
www.murata-ps.com
Technical enquiries email: [email protected], tel: +1 508 339 3000
MDC_UVQ Models.B11 Page 22 of 25
UVQ Series
Low Profile, Isolated Quarter Brick
2.5–40 Amp DC/DC Converters
UVQ Series Aluminum Heatsink
The UVQ series converter baseplate can be attached either to an enclosure wall
or a heatsink to remove heat from internal power dissipation. The discussion
below concerns only the heatsink alternative. The UVQ’s are available with a
low-profile extruded aluminum heatsink kit, models HS-QB25-UVQ, HS-QB50UVQ, and HS-QB100-UVQ. This kit includes the heatsink, thermal mounting
pad, screws and mounting hardware. See the assembly diagram below. Do not
overtighten the screws in the tapped holes in the converter. This kit adds excellent thermal performance without sacrificing too much component height. See
the Mechanical Outline Drawings for assembled dimensions. If the thermal pad
is firmly attached, no thermal compound (“thermal grease”) is required.
Thermal Performance
The HS-QB25-UVQ heatsink has a thermal resistance of 12 °C/Watt of internal
heat dissipation with “natural convection” airflow (no fans or other mechanical
airflow) at sea level altitude. This thermal resistance assumes that the heatsink
is firmly attached using the supplied thermal pad and that there is no nearby
wall or enclosure surface to inhibit the airflow. The thermal pad adds a negligible series resistance of approximately 0.5°C/Watt so that the total assembled
resistance is 12.5°C/Watt.
Be aware that we need to handle only the internal heat dissipation, not the
full power output of the converter. This internal heat dissipation is related to the
efficiency as follows:
Power Dissipation [Pd] = Power In – Power Out [1]
Power Out / Power In = Efficiency [in %] / 100 [2]
0!.(%!$3#2%7
-8-0,#3
Power Dissipation [Pd] = Power In x (1 –Efficiency%/100) [3]
Power Dissipation [Pd] = Power Out x (1 / (Efficiency%/100) - 1) [4]
Efficiency of course varies with input voltage and the total output power.
Please refer to the Performance Curves.
,/#+7!3(%2
-
0,#3
&,!47!3(%2
./
0,#3
Since many applications do include fans, here is an approximate equation to
calculate the net thermal resistance:
R4 [at airflow] = R4 [natural convection] / (1 + (Airflow in LFM) x
[Airflow Constant]) [5]
Where,
R4 [at airflow] is the net thermal resistance (in °C/W) with the amount of
airflow available and,
(%!43).+
R4 [natural convection] is the still air total path thermal resistance or in this
case 12.5°C/Watt and,
“Airflow in LFM” is the net air movement flow rate immediately at the converter.
(%!442!.3&%20!$
0EELOFFWHITEPLASTIC
BACKINGMATERIALBEFORE
ATTACHINGTOHEATSINK
Figure 7. Model UVQ Heatsink Assembly Diagram
When assembling these kits onto the converter, include ALL kit hardware to
assure adequate mechanical capture and proper clearances. Thread relief is
0.090" (2.3mm).
www.murata-ps.com
This equation simplifies an otherwise complex aerodynamic model but is a
useful starting point. The “Airflow Constant” is dependent on the fan and enclosure geometry. For example, if 200 LFM of airflow reduces the effective natural
convection thermal resistance by one half, the airflow constant would be
0.005. There is no practical way to publish a “one size fits all” airflow constant
because of variations in airflow direction, heatsink orientation, adjacent walls,
enclosure geometry, etc. Each application must be determined empirically and
the equation is primarily a way to help understand the cooling arithmetic.
This equation basically says that small amounts of forced airflow are quite
effective removing the heat. But very high airflows give diminishing returns.
Conversely, no forced airflow causes considerable heat buildup. At zero airflow,
cooling occurs only because of natural convection over the heatsink. Natural
convection is often well below 50 LFM, not much of a breeze.
While these equations are useful as a conceptual aid, most users find it
very difficult to measure actual airflow rates at the converter. Even if you know
the velocity specifications of the fan, this does not usually relate directly to
the enclosure geometry. Be sure to use a considerable safety margin doing
thermal analysis. If in doubt, measure the actual heat sink temperature with
a calibrated thermocouple, RTD or thermistor. Safe operation should keep the
heat sink below 100°C.
Technical enquiries email: [email protected], tel: +1 508 339 3000
MDC_UVQ Models.B11 Page 23 of 25
UVQ Series
Low Profile, Isolated Quarter Brick
2.5–40 Amp DC/DC Converters
Calculating Maximum Power Dissipation
To determine the maximum amount of internal power dissipation, find the
ambient temperature inside the enclosure and the airflow (in Linear Feet per
Minute – LFM) at the converter. Determine the expected heat dissipation using
the Efficiency curves and the converter Input Voltage. You should also compensate for lower atmospheric pressure if your application altitude is considerably
above sea level.
The general proceedure is to compute the expected temperature rise of the
heatsink. If the heatsink exceeds +100°C. either increase the airflow and/or
reduce the power output. Start with this equation:
Internal Heat Dissipation [Pd in Watts] = (Ts – Ta)/R4 [at airflow] [6]
where “Ta” is the enclosure ambient air temperature and,
where “Ts” is the heatsink temperature and,
where “R4 [at airflow]” is a specific heat transfer thermal resistance (in
degrees Celsius per Watt) for a particular heat sink at a set airflow rate. We
have already estimated R4 [at airflow] in the equations above.
Note particularly that Ta is the air temperature inside the enclosure at the
heatsink, not the outside air temperature. Most enclosures have higher internal
temperatures, especially if the converter is “downwind” from other heat-producing circuits. Note also that this “Pd” term is only the internal heat dissipated
inside the converter and not the total power output of the converter.
We can rearrange this equation to give an estimated temperature rise of the
heatsink as follows:
Heat Sink Example
Assume an efficiency of 92% and power output of 100 Watts. Using equation
[4], Pd is about 8.7 Watts at an input voltage of 48 Volts. Using +30°C ambient
temperature inside the enclosure, we wish to limit the heat sink temperature to
+90°C maximum baseplate temperature to stay well away from thermal shutdown. The +90°C. figure also allows some margin in case the ambient climbs
above +30°C or the input voltage varies, giving us less than 92% efficiency.
The heat sink and airflow combination must have the following characteristics:
8.7 W = (90-30) / R4[airflow] or,
R4[airflow] = 60/8.7 = 6.9°C/W
Since the ambient thermal resistance of the heatsink and pad is 12.5°C/W,
we need additional forced cooling to get us down to 6.9°C/W. Using a hypothetical airflow constant of 0.005, we can rearrange equation [5] as follows:
(Required Airflow, LFM) x (Airflow Constant) = R4[Nat.Convection] /
R4[at airflow] –1
or, (Required Airflow, LFM) x (Airflow Constant) = 12.5/6.9 –1 = 0.81 and,
rearranging again,
(Required Airflow, LFM) = 0.81/0.005 = 162 LFM
162 LFM is the minumum airflow to keep the heatsink below +90°C.
Increase the airflow to several hundred LFM to reduce the heatsink temperature further and improve life and reliability.
Ts = (Pd x R4 [at airflow]) + Ta [7]
2.28
(57.91)
Heatsink Kit *
Model Number
Still Air (Natural convection)
thermal resistance
Heatsink height
(see drawing)
HS-QB25-UVQ
12°C/Watt
0.25" (6.35mm)
HS-QB50-UVQ
10.6°C/Watt
0.50" (12.7mm)
HS-QB100-UVQ
8°C/Watt
1.00" (25.4mm)
1.860
(47.24)
* Kit includes heatsink, thermal pad and mounting hardware.
1.03
1.45
(26.16) (36.83)
0.140 DIA. (3.56) (4 PLACES)
*
MATERIAL: BLACK ANODIZED ALUMINUM
0.10
(2.54)
* UVQ SERIES HEATSINKS ARE AVAILABLE IN 3 HEIGHTS:
0.25 (6.35), 0.50 (12.70) AND 1.00 (25.4)
Dimensions in inches (mm)
www.murata-ps.com
Technical enquiries email: [email protected], tel: +1 508 339 3000
MDC_UVQ Models.B11 Page 24 of 25
UVQ Series
Low Profile, Isolated Quarter Brick
2.5–40 Amp DC/DC Converters
Case C59 with Baseplate
2.30 (58.4)
1.860 (47.2)
A
B
A
B
Case C59
0.42
(10.7)
PINS 1-3, 5-7: 0.040 ±0.001 (1.016 ±0.025)
PINS 4 & 8: 0.060 ±0.001 (1.52 ±0.025)
2.00 (50.8)
1.45
(36.8)
1.030
(26.2)
0.188
(4.78)
B
B
A
1
4
5
6
7
2
0.600
(15.24)
4 EQ. SP.
@ 0.150
(3.81)
8
3
BASEPLATE
#M3-THREAD X 0.15 DEEP
TYPICAL (4) PLACES
1.45
(36.8)
0.50
(12.7)
PINS 1-3, 5-7: 0.040 ±0.001 (1.016 ±0.025)
PINS 4 & 8: 0.060 ±0.001 (1.52 ±0.025)
BOTTOM VIEW
0.188
(4.8)
Alternate pin lengths are available. Contact Murata Power Solutions.
Dimensions are in inches (mm shown for ref. only).
2.30 (58.4)
2.00 (50.8)
Optional baseplate pin
is special order.
Contact Murata Power Solutions..
A
B
Third Angle Projection
A
0.15 (3.81)
1
9
Tolerances (unless otherwise specified):
.XX ± 0.02 (0.5)
.XXX ± 0.010 (0.25)
Angles ± 2˚
2
Optional pin 9 connects
to baseplate. Electrically
isolated from converter.
4
5
6
7
0.600 (15.24)
4 EQ. SP.
@ 0.150 (3.81)
8
Components are shown for reference only.
3
I/O CONNECTIONS
Pin
Function P32
1
–Input
2
On/Off Control
3
+Input
4
–Output
5
–Sense
6
Output Trim
7
+Sense
8
+Output
BOTTOM VIEW
Important: If sense inputs
are not connected to a
remote load, connect them
to their respective VOUT pins
at the converter.
USA:
Murata Power Solutions, Inc.
11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A.
Tel: (508) 339-3000 (800) 233-2765 Fax: (508) 339-6356
www.murata-ps.com email: [email protected] ISO 9001 and 14001 REGISTERED
03/05/09
Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other
technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply
the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without
notice.
© 2008 Murata Power Solutions, Inc.
www.murata-ps.com
Mansfield (MA), Tel: (508) 339-3000, email: [email protected]
Canada:
Toronto, Tel: (866) 740-1232, email: [email protected]
UK:
Milton Keynes, Tel: +44 (0)1908 615232, email: [email protected]
France:
Montigny Le Bretonneux, Tel: +33 (0)1 34 60 01 01, email: [email protected]
Germany:
München, Tel: +49 (0)89-544334-0, email: [email protected]
Japan:
Tokyo, Tel: 3-3779-1031, email: [email protected]
Osaka, Tel: 6-6354-2025, email: [email protected]
China:
Shanghai, Tel: +86 215 027 3678, email: [email protected]
Guangzhou, Tel: +86 208 221 8066, email: [email protected]
Singapore:
Parkway Centre, Tel: +65 6348 9096, email: [email protected]
Technical enquiries email: [email protected], tel: +1 508 339 3000
MDC_UVQ Models.B11 Page 25 of 25