FAIRCHILD NM24C09U

NM24C08U/NM24C09U
8K-Bit Serial EEPROM
2-Wire Bus Interface
General Description,
Functions
The NM24C08U/09U devices are 8K (8,192) bit serial interface
CMOS EEPROMs (Electrically Erasable Programmable ReadOnly Memory). These devices fully conform to the Standard I2C™
2-wire protocol which uses Clock (SCL) and Data I/O (SDA) pins
to synchronously clock data between the "master" (for example a
microprocessor) and the "slave" (the EEPROM device). In addition, the serial interface allows a minimal pin count packaging
designed to simplify PC board layout requirements and offers the
designer a variety of low voltage and low power options.
■ I2C™ compatible interface
■ 8,192 bits organized as 1,024 x 8
■ Extended 2.7V – 5.5V operating voltage
■ 100 KHz or 400 KHz operation
■ Self timed programming cycle (6ms typical)
■ "Programming complete" indicated by ACK polling
■ NM24C09U: Memory "Upper Block" Write Protect pin
Features
NM24C09U incorporates a hardware "Write Protect" feature, by
which, the upper half of the memory can be disabled against
programming by connecting the WP pin to VCC. This section of
memory then effectively becomes a ROM (Read-Only Memory)
and can no longer be programmed as long as WP pin is connected
to VCC.
■ The I2C™ interface allows the smallest I/O pincount of any
EEPROM interface
■ 16 byte page write mode to minimize total write time per byte
■ Typical 200µA active current (ICCA)
■ Typical 1µA standby current (ISB) for "L" devices and 0.1µA
standby current for "LZ" devices
Fairchild EEPROMs are designed and tested for applications requiring high endurance, high reliability and low power consumption for a
continuously reliable non-volatile solution for all markets.
■ Endurance: Up to 1,000,000 data changes
■ Data retention greater than 40 years
Block Diagram
VCC
VSS
WP
H.V. GENERATION
TIMING &CONTROL
START
STOP
LOGIC
SDA
CONTROL
LOGIC
SLAVE ADDRESS
REGISTER &
COMPARATOR
SCL
XDEC
A2
E2PROM
ARRAY
WORD
ADDRESS
COUNTER
R/W
YDEC
CK
DATA REGISTER
DIN
DOUT
DS800009-1
I2C™ is a registered trademark of Philips Electronics N.V.
© 1999 Fairchild Semiconductor Corporation
NM24C08U/09U Rev. B.1
1
www.fairchildsemi.com
NM24C08U/NM24C09U – 8K-BitŁ Serial EEPROM 2-Wire Bus Interface
August 1999
NM24C08U/NM24C09U – 8K-BitŁ Serial EEPROM 2-Wire Bus Interface
Connection Diagrams
Dual-In-Line Package (N), SO Package (M8), and TSSOP Package (MT8)
NC
1
8
VCC
NC
2
7
NC
A2
3
6
SCL
VSS
4
5
SDA
NM24C08U
DS800009-2
Top View
See Package Number N08E, M08A, and MTC08
Pin Names
A2
Device Address Input
VSS
Ground
SDA
Serial Data I/O
SCL
Serial Clock Input
NC
No Connection
VCC
Power Supply
Dual-In-Line Package (N), SO Package (M8), and TSSOP Package (MT8)
NC
1
NC
2
A2
3
VSS
4
NM24C09U
8
VCC
7
WP
6
SCL
5
SDA
DS800009-5
Top View
See Package Number N08E, M08A, and MTC08
Pin Names
NC
No Connection
A2
Device Address Input
VSS
Ground
SDA
Serial Data I/O
SCL
Serial Clock input
WP
Write Protect
VCC
Power Supply
2
NM24C08U/09U Rev. B.1
www.fairchildsemi.com
NM
24
C
XX
U
F
LZ
E
XX
Letter
Description
N
M8
MT8
8-pin DIP
8-pin SOIC
8-pin TSSOP
Temp. Range
None
V
E
0 to 70°C
-40 to +125°C
-40 to +85°C
Voltage Operating Range
Blank
L
LZ
4.5V to 5.5V
2.7V to 5.5V
2.7V to 5.5V and
<1µA Standby Current
SCL Clock Frequency
Blank
F
100KHz
400KHz
Ultralite
CS100UL Process
08
09
8K
8K with Write Protect
C
W
CMOS Technology
Total Array Write Protect
24
IIC
NM
Fairchild Non-Volatile
Memory
Package
Density
Interface
3
NM24C08U/09U Rev. B.1
www.fairchildsemi.com
NM24C08U/NM24C09U – 8K-BitŁ Serial EEPROM 2-Wire Bus Interface
Ordering Information
Operating Conditions
Absolute Maximum Ratings
Ambient Storage Temperature
Ambient Operating Temperature
NM24C08U/09U
NM24C08UE/09UE
NM24C08UV/09UV
–65°C to +150°C
All Input or Output Voltages
with Respect to Ground
6.5V to –0.3V
Lead Temperature
(Soldering, 10 seconds)
+300°C
ESD Rating
0°C to +70°C
-40°C to +85°C
-40°C to +125°C
Positive Power Supply
NM24C08U/09U
NM24C08UL/09UL
NM24C08ULZ/09ULZ
2000V min.
4.5V to 5.5V
2.7V to 5.5V
2.7V to 5.5V
Standard VCC (4.5V to 5.5V) DC Electrical Characteristics
Symbol
Parameter
Test Conditions
Min
Limits
Typ
(Note 1)
Max
Units
0.2
1.0
mA
ICCA
Active Power Supply Current
fSCL = 400 KHz
fSCL = 100 KHz
ISB
Standby Current
VIN = GND or VCC
10
50
µA
ILI
Input Leakage Current
VIN = GND to VCC
0.1
1
µA
ILO
Output Leakage Current
VOUT = GND to VCC
0.1
1
µA
VIL
Input Low Voltage
–0.3
VCC x 0.3
V
VIH
Input High Voltage
VCC x 0.7
VCC + 0.5
V
VOL
Output Low Voltage
0.4
V
IOL = 3 mA
Low VCC (2.7V to 5.5V) DC Electrical Characteristics
Symbol
Parameter
Test Conditions
Min
Limits
Typ
(Note 1)
Max
Units
ICCA
Active Power Supply Current fSCL = 400 KHz
fSCL = 100 KHz
0.2
1.0
mA
ISB
Standby Current
VIN = GND
or VCC
1
0.1
10
10
1
50
µA
µA
µA
ILI
Input Leakage Current
VIN = GND to VCC
0.1
1
µA
VOUT = GND to VCC
VCC = 2.7V - 4.5V
VCC = 2.7V - 4.5V
VCC = 4.5V - 5.5V
ILO
Output Leakage Current
1
µA
VIL
Input Low Voltage
–0.3
VCC x 0.3
V
VIH
Input High Voltage
VCC x 0.7
VCC + 0.5
V
VOL
Output Low Voltage
0.4
V
0.1
IOL = 3 mA
Capacitance TA = +25°C, f = 100/400 KHz, VCC = 5V (Note 2)
Symbol
Test
Conditions
Max
Units
CI/O
Input/Output Capacitance (SDA)
VI/O = 0V
8
pF
CIN
Input Capacitance (A0, A1, A2, SCL)
VIN = 0V
6
pF
Note 1: Typical values are TA = 25°C and nominal supply voltage (5V).
Note 2: This parameter is periodically sampled and not 100% tested.
4
NM24C08U/09U Rev. B.1
www.fairchildsemi.com
NM24C08U/NM24C09U – 8K-BitŁ Serial EEPROM 2-Wire Bus Interface
Product Specifications
Input Pulse Levels
VCC x 0.1 to VCC x 0.9
Input Rise and Fall Times
10 ns
Input & Output Timing Levels
VCC x 0.5
Output Load
1 TTL Gate and CL = 100 pF
Read and Write Cycle Limits (Standard and Low VCC Range 2.7V - 5.5V)
Symbol
fSCL
TI
Parameter
100 KHz
Min
Max
400 KHz
Min
Max
Units
SCL Clock Frequency
100
400
KHz
Noise Suppression Time Constant at
SCL, SDA Inputs (Minimum VIN
Pulse width)
100
50
ns
0.9
µs
tAA
SCL Low to SDA Data Out Valid
0.3
tBUF
Time the Bus Must Be Free before
a New Transmission Can Start
4.7
1.3
µs
Start Condition Hold Time
4.0
0.6
µs
tLOW
Clock Low Period
4.7
1.5
µs
tHIGH
Clock High Period
4.0
0.6
µs
tSU:STA
Start Condition Setup Time
(for a Repeated Start Condition)
4.7
0.6
µs
tHD:DAT
Data in Hold Time
0
0
µs
tSU:DAT
Data in Setup Time
250
100
ns
tHD:STA
tR
SDA and SCL Rise Time
tF
SDA and SCL Fall Time
tSU:STO
tDH
tWR
(Note 3)
3.5
0.1
1
0.3
300
300
µs
ns
Stop Condition Setup Time
4.7
0.6
µs
Data Out Hold Time
300
50
ns
Write Cycle Time - NM24C08U/09U
- NM24C08U/09UL, NM24C08U/09ULZ
10
15
10
15
ms
Note 3: The write cycle time (tWR) is the time from a valid stop condition of a write sequence to the end of the internal erase/program cycle. During the write cycle, the
NM24C08U/09U bus interface circuits are disabled, SDA is allowed to remain high per the bus-level pull-up resistor, and the device does not respond to its slave address.
5
NM24C08U/09U Rev. B.1
www.fairchildsemi.com
NM24C08U/NM24C09U – 8K-BitŁ Serial EEPROM 2-Wire Bus Interface
AC Conditions of Test
tR
tF
tHIGH
tLOW
tLOW
SCL
;;
tSU:STA
SDA
tHD:DAT
tHD:STA
tSU:STO
tSU:DAT
IN
tBUF
tAA
tDH
SDA
OUT
System Layout
DS800009-8
Typical System Configuration
VCC
VCC
SDA
SCL
Master
Transmitter/
Receiver
Note:
Slave
Transmitter/
Receiver
Slave
Receiver
Master
Transmitter
Master
Transmitter/
Receiver
DS800009-20
Due to open drain configuration of SDA, a bus-level pull-up resistor is called for, (typical value = 4.7kΩ)
Example of 16K of Memory on 2-Wire Bus
Note:
VCC
The SDA pull-up resistor is required due to the open-drain/open collector output of IIC bus devices.
The SCL pull-up resistor is recommended because of the normal SCL line inactive 'high' state.
It is recommended that the total line capacitance be less than 400pF
VCC
SDA
SCL
VCC
VCC
VCC
NM24C02U/03U
NM24C02U/03U
A0 A1 A2 VSS
A0 A1 A2 VSS
To VCC or VSS
VCC
NM24C04U/05U
A1 A2 VSS
To VCC or VSS
To VCC or VSS
NM24C08U/09U
A2 VSS
To VCC or VSS
DS800009-9
Device
NM24C08U/09U
A0
Address Pins
A1
A2
No Connect
No Connect
ADR
6
NM24C08U/09U Rev. B.1
Memory Size
# of Page
Blocks
8192 Bits
4
www.fairchildsemi.com
NM24C08U/NM24C09U – 8K-BitŁ Serial EEPROM 2-Wire Bus Interface
Bus Timing
Pin Descriptions
Device address pin A2 is connected to VCC or VSS to configure
the EEPROM chip address. Table 1 shows the active pin.
Serial Clock (SCL)
Table 1.
Serial Data (SDA)
Device
A0
A1
NM24C08U/09U
x
x
A2
The SCL input is used to clock all data into and out of the device.
SDA is a bidirectional pin used to transfer data into and out of the
device. It is an open drain output and may be wire–ORed with any
number of open drain or open collector outputs.
Effects of Addresses
ADR 21 = 2; 2 x (4 x 2k) = 16K
WP Write Protection (NM24C09U Only)
Background Information (IIC Bus)
If tied to VCC, PROGRAM operations onto the upper half of the
memory will not be executed. READ operations are possible. If
tied to VSS, normal operation is enabled, READ/WRITE over the
entire memory is possible.
As mentioned, the IIC bus allows synchronous bidirectional communication between Transmitter/Receiver using the SCL (clock)
and SDA (Data I/O) lines. All communication must be started with
a valid START condition, concluded with a STOP condition and
acknowledged by the Receiver with an ACKNOWLEDGE condition.
This feature allows the user to assign the upper half of the memory
as ROM which can be protected against accidental programming.
When write is disabled, slave address and word address will be
acknowledged but data will not be acknowledged.
As shown below, the EEPROMs on the IIC bus may be configured
in any manner required, the total memory addressed can not
exceed 16K (16,384 bits). EEPROM memory address programming is controlled by 2 methods:
Device Operation
The NM24C08U/09U supports a bidirectional bus oriented protocol. The protocol defines any device that sends data onto the bus
as a transmitter and the receiving device as the receiver. The
device controlling the transfer is the master and the device that is
controlled is the slave. The master will always initiate data
transfers and provide the clock for both transmit and receive
operations. Therefore, the NM24C08U/09U will be considered a
slave in all applications.
• Hardware configuring the A2 pin (Device Address pin) with
pull-up or pull-down to VCC or VSS. All unused pins must be
grounded (tied to VSS).
• Software addressing the required PAGE BLOCK within the
device memory array (as sent in the Slave Address string).
For devices with densities greater than 16K, a different protocol,
the Extended IIC protocol, is used. Refer to NM24C32U datasheet
(for example) for additional details.
Clock and Data Conventions
Addressing an EEPROM memory location involves sending a
command string with the following information:
[DEVICE TYPE]–[DEVICE ADDRESS]–[PAGE BLOCK ADDRESS]–[BYTE ADDRESS]
Data states on the SDA line can change only during SCL LOW.
SDA state changes during SCL HIGH are reserved for indicating
start and stop conditions. Refer to Figure 2 and Figure 3 on next
page.
Start Condition
DEFINITIONS
BYTE
8 bits (byte) of data
PAGE
16 sequential addresses (one byte
each) that may be programmed
during a 'Page Write' programming
cycle
PAGE BLOCK
2048 (2K) bits organized into 16
pages of addressable memory.
(8 bits) x (16 bytes) x (16 pages)
= 2048 bits
MASTER
SLAVE
TRANSMITTER
RECEIVER
All commands are preceded by the start condition, which is a
HIGH to LOW transition of SDA when SCL is HIGH. The
NM24C08U/09U continuously monitors the SDA and SCL lines for
the start condition and will not respond to any command until this
condition has been met.
Stop Condition
All communications are terminated by a stop condition, which is a
LOW to HIGH transition of SDA when SCL is HIGH. The stop
condition is also used by the NM24C08U/09U to place the device
in the standby power mode.
Any IIC device CONTROLLING the
transfer of data (such as a
microprocessor)
Write Cycle Timing
Acknowledge
Device being controlled
(EEPROMs are always considered
Slaves)
Acknowledge is a hardware convention used to indicate successful data transfers. The transmitting device, either master or slave,
will release the bus after transmitting eight bits.
Device currently SENDING data on
the bus (may be either a Master or
Slave).
During the ninth clock cycle the receiver will pull the SDA line to
LOW to acknowledge that it received the eight bits of data. Refer
to Figure 4.
Device currently RECEIVING data
on the bus (Master or Slave)
7
NM24C08U/09U Rev. B.1
www.fairchildsemi.com
NM24C08U/NM24C09U – 8K-BitŁ Serial EEPROM 2-Wire Bus Interface
Device Operation Input (A2)
SCL
SDA
8th BIT
ACK
WORD n
tWR
STOP
CONDITION
Note:
START
CONDITION
DS800009-10
The write cycle time (tWR) is the time from a valid stop condition of a write sequence to the end of the internal erase/program cycle.
Data Validity (Figure 2)
SCL
SDA
DATA STABLE
DATA
CHANGE
DS800009-11
Start and Stop Definition (Figure 3)
SCL
SDA
START
CONDITION
STOP
CONDITION
DS800009-12
Acknowledge Response from Receiver (Figure 4)
SCL FROM
MASTER
1
8
9
DATA OUTPUT
FROM
TRANSMITTER
DATA OUTPUT
FROM
RECEIVER
START
ACKNOWLEDGE
8
NM24C08U/09U Rev. B.1
DS800009-13
www.fairchildsemi.com
NM24C08U/NM24C09U – 8K-BitŁ Serial EEPROM 2-Wire Bus Interface
Write Cycle Timing
Refer to the following table for Slave Addresses string details:
Device
The NM24C08U/09U device will always respond with an acknowledge after recognition of a start condition and its slave address. If
both the device and a write operation have been selected, the
NM24C08U/09U will respond with an acknowledge after the
receipt of each subsequent eight bit byte.
NM24C08U/09U
NM24C08U/09U
Device
Address
0
A2
A1
A0
R/W
4
00 01 10 11
A simple review: After the NM24C08U/09U recognizes the start
condition, the devices interfaced to the IIC bus wait for a slave
address to be transmitted over the SDA line. If the transmitted
slave address matches an address of one of the devices, the
designated slave pulls the line LOW with an acknowledge signal
and awaits further transmissions.
Slave Addresses (Figure 5)
1
A
The last bit of the slave address defines whether a write or read
condition is requested by the master. A '1' indicates that a read
operation is to be executed, and a '0' initiates the write mode.
Following a start condition the master must output the address of
the slave it is accessing. The most significant four bits of the slave
address are those of the device type identifier (see Figure 5). This
is fixed as 1010 for all EEPROM devices.
0
P
All IIC EEPROMs use an internal protocol that defines a PAGE
BLOCK size of 2K bits (for Word addressess 0000 through 1111).
Therefore, address bits A0, A1, or A2 (if designated 'P') are used
to access a PAGE BLOCK in conjunction with the Word address
used to access any individual data byte (Word).
Device Addressing
1
P
A: Refers to a hardware configured Device Address pin
P: Refers to an internal PAGE BLOCK memory segment.
In the read mode the NM24C08U/09U slave will transmit eight bits
of data, release the SDA line and monitor the line for an acknowledge. If an acknowledge is detected and no stop condition is
generated by the master, the slave will continue to transmit data.
If an acknowledge is not detected, the slave will terminate further
data transmissions and await the stop condition to return to the
standby power mode.
Device Type
Identifier
A0 A1 A2 Page Page Block
Blocks Addresses
(LSB)
Page
Block Address
DS800009-14
9
NM24C08U/09U Rev. B.1
www.fairchildsemi.com
NM24C08U/NM24C09U – 8K-BitŁ Serial EEPROM 2-Wire Bus Interface
Write Cycle Timing (Continued)
Once the stop condition is issued to indicate the end of the host’s
write operation the NM24C08U/09U initiates the internal write
cycle. ACK polling can be initiated immediately. This involves
issuing the start condition followed by the slave address for a write
operation. If the NM24C08U/09U is still busy with the write
operation no ACK will be returned. If the NM24C08U/09U has
completed the write operation an ACK will be returned and the
host can then proceed with the next read or write operation.
BYTE WRITE
For a write operation a second address field is required which is
a word address that is comprised of eight bits and provides access
to any one of the 256 bytes in the selected page of memory. Upon
receipt of the byte address the NM24C08U/09U responds with an
acknowledge and waits for the next eight bits of data, again,
responding with an acknowledge. The master then terminates the
transfer by generating a stop condition, at which time the
NM24C08U/09U begins the internal write cycle to the nonvolatile
memory. While the internal write cycle is in progress the
NM24C08U/09U inputs are disabled, and the device will not
respond to any requests from the master. Refer to Figure 6 for the
address, acknowledge and data transfer sequence.
Write Protection (NM24C09U Only)
Programming of the upper half of the memory will not take place
if the WP pin of the NM24C09U is connected to VCC. The
NM24C09U will accept slave and byte addresses; but if the
memory accessed is write protected by the WP pin, the NM24C09U
will not generate an acknowledge after the first byte of data has
been received, and thus the program cycle will not be started when
the stop condition is asserted.
PAGE WRITE
The NM24C08U/09U is capable of a sixteen byte page write
operation. It is initiated in the same manner as the byte write
operation; but instead of terminating the write cycle after the first
data byte is transferred, the master can transmit up to fifteen more
bytes. After the receipt of each byte, the NM24C08U/09U will
respond with an acknowledge.
After the receipt of each byte, the internal address counter
increments to the next address and the next SDA data is accepted.
If the master should transmit more than sixteen bytes prior to
generating the stop condition, the address counter will "roll over"
and the previously written data will be overwritten. As with the byte
write operation, all inputs are disabled until completion of the
internal write cycle. Refer to Figure 7 for the address, acknowledge, and data transfer sequence.
Byte Write (Figure 6)
Bus Activity:
Master
S
T
A
R
T
SLAVE
ADDRESS
WORD
ADDRESS
S
T
O
P
DATA
SDA Line
A
C
K
Bus Activity:
NM24C08U/09U
A
C
K
A
C
K
DS800009-15
Page Write (Figure 7)
Bus Activity:
Master
S
T
A
R
T
SLAVE
ADDRESS
WORD ADDRESS (n)
DATA n
DATA n + 1
S
T
O
P
DATA n + 15
SDA Line
Bus Activity:
NM24C08U/09U
A
C
K
A
C
K
A
C
K
A
C
K
DS800009-16
10
NM24C08U/09U Rev. B.1
A
C
K
www.fairchildsemi.com
NM24C08U/NM24C09U – 8K-BitŁ Serial EEPROM 2-Wire Bus Interface
Acknowledge Polling
Write Operations
Read operations are initiated in the same manner as write
operations, with the exception that the R/W bit of the slave
address is set to a one. There are three basic read operations:
current address read, random read, and sequential read.
start condition and the slave address with the R/W bit set to one.
This will be followed by an acknowledge from the NM24C08U/09U
and then by the eight bit data. The master will not acknowledge the
transfer but does generate the stop condition, and therefore the
NM24C08U/09U discontinues transmission. Refer to Figure 9 for
the address, acknowledge and data transfer sequence.
Current Address Read
Sequential Read
Internally the NM24C08U/09U contains an address counter that
maintains the address of the last byte accessed, incremented by
one. Therefore, if the last access (either a read or write) was to
address n, the next read operation would access data from
address n + 1. Upon receipt of the slave address with R/W set to
one, the NM24C08U/09U issues an acknowledge and transmits
the eight bit byte. The master will not acknowledge the transfer
but does generate a stop condition, and therefore the NM24C08U/
09U discontinues transmission. Refer to Figure 8 for the sequence of address, acknowledge and data transfer.
Sequential reads can be initiated as either a current address read
or random access read. The first word is transmitted in the same
manner as the other read modes; however, the master now
responds with an acknowledge, indicating it requires additional
data. The NM24C08U/09U continues to output data for each
acknowledge received. The read operation is terminated by the
master not responding with an acknowledge or by generating a
stop condition.
The data output is sequential, with the data from address n
followed by the data from n + 1. The address counter for read
operations increments all word address bits, allowing the entire
memory contents to be serially read during one operation. After
the entire memory has been read, the counter "rolls over" and the
NM24C08U/09U continues to output data for each acknowledge
received. Refer to Figure 10 for the address, acknowledge, and
data transfer sequence.
Random Read
Random read operations allow the master to access any memory
location in a random manner. Prior to issuing the slave address
with the R/W bit set to one, the master must first perform a
“dummy” write operation. The master issues the start condition,
slave address and then the byte address it is to read. After the
byte address acknowledge, the master immediately reissues the
Current Address Read (Figure 8)
Bus Activity:
Master
S
T
A
R
T
S
T
O
P
SLAVE
ADDRESS
SDA Line
A
C
K
Bus Activity:
NM24C08U/09U
DATA
NO
A
C
K
DS800009-17
Random Read (Figure 9)
Bus Activity:
Master
S
T
A
R
T
SLAVE
ADDRESS
S
T
A
R
T
WORD
ADDRESS
S
T
O
P
SLAVE
ADDRESS
SDA Line
A
C
K
Bus Activity:
NM24C08U/09U
A
C
K
A
C
K
DATA n
NO
A
C
K
DS800009-18
Sequential Read (Figure 10)
Bus Activity:
Master
A
C
K
Slave
Address
S
T
O
P
A
C
K
A
C
K
SDA Line
Bus Activity:
NM24C08U/09U
A
C
K
DATA n +1
DATA n +1
DATA n + 2
DATA n + x
NO
A
C
K
DS800009-19
11
NM24C08U/09U Rev. B.1
www.fairchildsemi.com
NM24C08U/NM24C09U – 8K-BitŁ Serial EEPROM 2-Wire Bus Interface
Read Operations
NM24C08U/NM24C09U – 8K-BitŁ Serial EEPROM 2-Wire Bus Interface
Physical Dimensions inches (millimeters) unless otherwise noted
0.189 - 0.197
(4.800 - 5.004)
8 7 6 5
0.228 - 0.244
(5.791 - 6.198)
1 2 3 4
Lead #1
IDENT
0.150 - 0.157
(3.810 - 3.988)
0.010 - 0.020
x 45°
(0.254 - 0.508)
0.0075 - 0.0098
(0.190 - 0.249)
Typ. All Leads
8° Max, Typ.
All leads
0.053 - 0.069
(1.346 - 1.753)
0.004 - 0.010
(0.102 - 0.254)
Seating
Plane
0.04
(0.102)
All lead tips
0.014
(0.356)
0.016 - 0.050
(0.406 - 1.270)
Typ. All Leads
0.014 - 0.020 Typ.
(0.356 - 0.508)
0.050
(1.270)
Typ
8-Pin Molded Small Outline Package (M8)
Package Number M08A
0.114 - 0.122
(2.90 - 3.10)
8
5
(4.16) Typ (7.72) Typ
0.169 - 0.177
(4.30 - 4.50)
0.246 - 0.256
(6.25 - 6.5)
(1.78) Typ
(0.42) Typ
0.123 - 0.128
(3.13 - 3.30)
(0.65) Typ
1
Land pattern recommendation
4
Pin #1 IDENT
0.0433
Max
(1.1)
0.0256 (0.65)
Typ.
0.0035 - 0.0079
See detail A
0.002 - 0.006
(0.05 - 0.15)
0.0075 - 0.0098
(0.19 - 0.30)
Gage
plane
0°-8°
DETAIL A
Typ. Scale: 40X
0.020 - 0.028
(0.50 - 0.70)
Seating
plane
0.0075 - 0.0098
(0.19 - 0.25)
Notes: Unless otherwise specified
1. Reference JEDEC registration MO153. Variation AA. Dated 7/93
8-Pin Molded Thin Shrink Small Outline Package
Package Number MTC08
12
NM24C08U/09U Rev. B.1
www.fairchildsemi.com
0.373 - 0.400
(9.474 - 10.16)
0.090
(2.286)
8
0.092
DIA
(2.337)
7
6
0.250 - 0.005
+
Pin #1 IDENT
8
0.032 ± 0.005
(6.35 ± 0.127)
Pin #1
IDENT
1
Option 1
1
0.280 MIN
(7.112)
2
3
0.040 Typ.
(1.016)
0.300 - 0.320
(7.62 - 8.128)
7
(0.813 ± 0.127)
RAD
5
0.030
MAX
(0.762)
20° ± 1°
4
Option 2
0.145 - 0.200
0.039
(0.991)
(3.683 - 5.080)
0.130 ± 0.005
(3.302 ± 0.127)
95° ± 5°
0.009 - 0.015
(0.229 - 0.381)
+0.040
0.325 -0.015
+1.016
8.255 -0.381
0.125
(3.175)
DIA
NOM
0.125 - 0.140
(3.175 - 3.556)
0.065
(1.651)
90° ± 4°
Typ
0.018 ± 0.003
(0.457 ± 0.076)
0.100 ± 0.010
(2.540 ± 0.254)
0.045 ± 0.015
(1.143 ± 0.381)
0.020
(0.508)
Min
0.060
(1.524)
0.050
(1.270)
Molded Dual-In-Line Package (N)
Package Number N08E
Life Support Policy
Fairchild's products are not authorized for use as critical components in life support devices or systems without the express written
approval of the President of Fairchild Semiconductor Corporation. As used herein:
1. Life support devices or systems are devices or systems which,
(a) are intended for surgical implant into the body, or (b) support
or sustain life, and whose failure to perform, when properly
used in accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a significant
injury to the user.
Fairchild Semiconductor
Americas
Customer Response Center
Tel. 1-888-522-5372
2. A critical component is any component of a life support device
or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system,
or to affect its safety or effectiveness.
Fairchild Semiconductor
Europe
Fax:
+44 (0) 1793-856858
Deutsch
Tel:
+49 (0) 8141-6102-0
English
Tel:
+44 (0) 1793-856856
Français
Tel:
+33 (0) 1-6930-3696
Italiano
Tel:
+39 (0) 2-249111-1
Fairchild Semiconductor
Hong Kong
8/F, Room 808, Empire Centre
68 Mody Road, Tsimshatsui East
Kowloon. Hong Kong
Tel; +852-2722-8338
Fax: +852-2722-8383
13
NM24C08U/09U Rev. B.1
Fairchild Semiconductor
Japan Ltd.
4F, Natsume Bldg.
2-18-6, Yushima, Bunkyo-ku
Tokyo, 113-0034 Japan
Tel: 81-3-3818-8840
Fax: 81-3-3818-8841
www.fairchildsemi.com
NM24C08U/NM24C09U – 8K-BitŁ Serial EEPROM 2-Wire Bus Interface
Physical Dimensions inches (millimeters) unless otherwise noted