REVISION H ANY REV MADE TO THIS PRINT MUST HAVE AN UPDATED MKT PRINT NOTES: 1. USE ASP-103597-01-B BODY FOR NON-STANDARD 19 POSITION. 2. REPRESENTS A CRITICAL DIMENSION. 3. BURR ALLOWANCE: .0005[0.013] MAX. 4. MINIMUM PUSHOUT FORCE: .5 LB. 5. MAXIMUM ALLOWABLE BOW: .002[0.05] INCH/INCH AFTER ASSEMBLY. 6. CONTACT TO BE FLUSH +/-.002. 7. ONE REEL MINIMUM PLATING REQUIREMENT (85,000 CONTACTS PER REEL). 8. ALL DIMS TO BE SYMMETRICAL ABOUT THE CENTERLINE WITHIN ±.001[0.03]. 9. .0025[0.064] MAX VARIATION BETWEEN SOLDERBALLS. 10. REFER TO VISUAL INSPECTION BOARD FOR SOLDERBALL APPEARANCE CHECKS. 11. THE DISTANCE FROM THE CENTER OF ANY SOLDERBALL TO THE CENTER OF ANY ADJACENT INNER PEG SHALL BE .025±.005[0.64±0.13]. 12. PARTS TO BE PACKAGED IN TRAYS. DO NOT SCALE FROM THIS PRINT 1.070 27.18 REF .970 24.64 REF .900±.002 22.86±0.05 (18 POS x .0500[1.270]) 19 01 A B C .145 3.68 REF D .095 2.41 REF .250 6.35 .320 8.13 REF E F CRITICAL DIMENSION INSPECTION INSTRUCTION TABLE .035 0.89 REF ASSEMBLY OPERATION IN PROCESS INSPECTION FILL C-140-03-H C2, C3 ATTACH SDB-030-6337 C3 FINISHED GOOD INSPECTION C1, C3 "A" .104 2.64 REF 2 .134±.003 3.41±0.08 1 3 UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN INCHES. TOLERANCES ARE: DECIMALS ITEM NO. PART NUMBER QUANTITY MATERIAL 1 ASP-103597-01-B 1.0000 UL 94 V0, COLOR: BLACK 2 C-140-03-H 114.00 PHOS BRONZE, 521 HARD TEMPER 3 SDB-030-6337 114.00 63% TIN /37% LEAD 4 TY-YFS004-19-3-6 .01539 CONDUCTIVE POLYMER SECTION "A"-"A" .012 0.31 (SEE NOTE 9) "A" .XX: .01 .XXX: .005 .XXXX: .0020 ANGLES 2 PROPRIETARY NOTE THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF SAMTEC, INC. DO NOT SCALE DRAWING PLATING: CONTACT AREA: .000030 GOLD OVER .000050 NICKEL REMAINDER: .000003 FLASH GOLD OVER .000050 NICKEL F:\DWG\MISC\MKTG\ASP-103612-03-MKT.SLDDRW SHEET SCALE: 3:1 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PHONE: 812-944-6733 FAX: 812-948-5047 e-Mail [email protected] code 55322 DESCRIPTION: VITA 42 (LEAD FREE) SOCKET ASSEMBLY DWG. NO. BY: ASP-103612-03 J LACKEY 10/18/2006 SHEET 1 OF 2 ASP-103612-03 RECOMMENDED BOARD LAYOUT REVISION H .9000 22.860 01 19 A B C .2500 6.350 RECOMMENDED STENCIL LAYOUT D STENCIL TO BE .0060[0.152] THICK E F .900 22.86 "A" .050 1.27 (TYP) 01 19 NOTE: OUTER ROWS MAY NOT NEED VIAS - THIS IS LEFT TO THE DISCRETION OF THE BOARD DESIGNER. A B C .250 6.35 D E F .0250 0.635 .050 1.27 (TYP) .0250 0.635 (TYP) .0100 0.254 TRACE .0310 0.787 FREE OF SOLDER MASK 45° .0250 0.635 PAD .0100 0.254 VIA (PLATED) PROPRIETARY NOTE DETAIL "A" SCALE 12 : 1 .0200 0.508 PAD THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF SAMTEC, INC. SHEET SCALE: 3:1 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PHONE: 812-944-6733 FAX: 812-948-5047 e-Mail [email protected] code 55322 DESCRIPTION: VITA 42 (LEAD FREE) SOCKET ASSEMBLY DWG. NO. F:\DWG\MISC\MKTG\ASP-103612-03-MKT.SLDDRW BY: ASP-103612-03 J LACKEY 10/18/2006 SHEET 2 OF 2