2.5 Gbps Single Mode Transceiver C-1X-2500(C)-TDFB(3)-SSCX Features • SC Duplex Single Mode Transceiver • Industry Standard 1x9 Footprint • Complies with SONET OC-48 STM-16 • Single +3.3V / +5V Power Supply • Operating Temperature Range 0℃ ~ +70℃ • CML Differential Data Inputs and Outputs • PECL/LVPECL Signal Detection Output [C-1X-2500-TDFB(3)-SSCX] • TTL/LVTTL Signal Detection Output [C-1X-2500C-TDFB(3)-SSCX] • Wave Solderable and Aqueous Washable • Uncooled laser diode with MQW structure • Complies with Telcordia (Bellcore) GR-468-CORE Applications • STM 16/ OC-48, 2.5 Gigabit Absolute Maximum Rating Parameter Symbol Min. Max. Unit Note Power Supply Voltage Vcc 0 3.6 V C-1X-2500(C)-TDFB3-SSCX Power Supply Voltage Vcc 0 6 V C-1X-2500(C)-TDFB-SSCX Output Current Iout 0 30 mA Soldering Temperature - - 260 ºC Operating Temperature Topr 0 70 ºC Storage Temperature Tstg -40 85 ºC Symbol Min. Typ. Max. Unit Vcc 3.1 3.3 3.5 V 10 seconds on leads only Recommended Operating Condition Parameter Power Supply Voltage 1 Power Supply Voltage 1 Operating Temperature (Case) Vcc 4.75 5 5.25 V Topr 0 - 70 ºC - - 2488.32 - Mbit/s Data Rate Note1: Please refer to ordering information LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 1 LUMNDS797-Dec0904 rev. A.0 2.5 Gbps Single Mode Transceiver C-1X-2500(C)-TDFB(3)-SSCX Transmitter Specifications (Optical) Parameter Symbol Min Typical Max Unit Optical Transmit Power Po -5 - 0 dBm C-1X-2500(C)-TDFB(3)-SSC2 Optical Transmit Power Po 0 - +5 dBm C-1X-2500(C)-TDFB(3)-SSC4 Output center Wavelength λ 1280 1310 1355 nm C-13-2500(C)-TDFB(3)-SSCX λ 1500 1550 1580 nm C-15-2500(C)-TDFB(3)-SSCX ∆λ - - 1 nm -20 dB width SMSR 30 35 - dB CW, Po=5mW ER 8.2 - - dB Output center Wavelength Output Spectrum Width Side Mode Suppression Ratio Extinction Ratio Output Eye Notes Compliant with ITU recommendation G.957 Relative Intensity Noise RIN - - -120 dB/Hz TJ - - 0.18 ns Symbol Min Typical Max Unit ICC - - 260 mA Data Input Current-Low IIL -350 - - µA Data Input Current-High IIH - - 350 µA VIH-VIL 300 - - mV Symbol Min Typical Max Unit Total Jitter Measured with 223-1 PRBS with 72 ones and 72 zeros Transmitter Specifications (Electrical) Parameter Power Supply Current Data Input Voltage Notes Maximum current is specified at Vcc= Maximum @ maximum temperature Peak-peak, single ended, AC coupled Receiver Specifications (Optical) Parameter Sensitivity2 Notes - - - -20 dBm Maximum Input Power Pin 0 - - dBm Signal Detect-Asserted Pa - - -20 dBm Measured on transition: low to high Signal Detect-Deasserted Pd -38 - - dBm Measured on transition: high to low 1 - - dB 1100 - 1600 nm -27 dB Signal Detect-Hysteresis Wavelength of Operation Reflectance Note 2: Measured with 223-1 PRBS, BER= 10-10 Receiver Specifications (Electrical) Parameter Power Supply Current Data output Voltage Symbol Min Typical Max Unit Note ICC - - 100 mA The current excludes the output load current VOH -VOL 300 - 900 mV Peak-peak, single-ended, AC-coupled Signal Detect Output Voltage-Low VSDL - - 0.5 V Signal Detect Output Voltage-High VSDH 2.0 - - V Signal Detect Output Voltage-Low VSDL-Vcc -2.0 - -1.58 V Signal Detect Output Voltage-High VSDH- Vcc -1.1 - -0.74 V LUMINENTOIC.COM C-1X-2500C-TDFB(3)-SSCX C-1X-2500-TDFB(3)-SSCX 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 2 LUMNDS797-Dec0904 rev. A.0 2.5 Gbps Single Mode Transceiver C-1X-2500(C)-TDFB(3)-SSCX Connection Diagram 1. (Rx GND) 2. (Rx +) 3. (Rx-) 4. (SD) 5. (Rx Vcc) 6. (Tx Vcc) 7. (TX-) 8. (TX+) 9. (Tx GND) NC Top View NC Receiver Signal Ground Receiver Data Out Receiver Data Out Bar Signal Detect Receiver Power Supply Transmitter Power Supply Transmitter Data In Bar Transmitter Data in Transmitter Signal Ground PIN Symbol Notes 1 RxGND Directly connect this pin to the receiver ground plane 2 RD+ See recommended circuit schematic 3 RD- See recommended circuit schematic 4 SD Active high on this indicates a received optical signal 5 RxVcc DC power for the receiver section 6 TxVcc DC power for the transmitter section 7 TD- See recommended circuit schematic TD+ See recommended circuit schematic 8 Warnings 9 LUMINENTOIC.COM TxGND Directly connect this pin to the transmitter ground plane 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 3 LUMNDS797-Dec0904 rev. A.0 2.5 Gbps Single Mode Transceiver C-1X-2500(C)-TDFB(3)-SSCX Recommended Circuit Schematic C-1X-2500-TDFB(3)-SSCX Rx Vcc 9 8 7 6 5 4 3 2 1 C5 R1 TD + Z=50! TD - Z=50! Z=50! RD + Z=50! RD SD Tx Vcc Rx Vcc No internal connection Notes +3.3V: C1=C2=C5=0.1"F C3=C4=10"F L1=L2=1"H R1=130! R2=82! Transceiver Top view R2 No internal connection L1 C3 Vcc Notes +5V: C1=C2=C5=0.1"F C3=C4=10"F L1=L2=1"H R1=82! R2=130! Rx Vcc C1 L2 Tx Vcc C2 C4 C-1X-2500C-TDFB(3)-SSCX 7 6 5 9 8 TD + Z=50! TD - Z=50! 4 3 2 1 Z=50! RD + Z=50! RD SD Tx Vcc Rx Vcc No internal connection Transceiver Top view No internal connection L1 Notes: C1=C2=0.1"F C3=C4=10"F L1=L2=1"H Vcc C3 Rx Vcc C1 L2 C4 Tx Vcc C2 The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals. The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc. A GND plane under the module is required for good EMI and sensitivity performance. LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 4 LUMNDS797-Dec0904 rev. A.0 2.5 Gbps Single Mode Transceiver C-1X-2500(C)-TDFB(3)-SSCX Package Diagram Units in mm SC Transceiver Assembly 9.8mm Front View Top View Rear View Side View LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 5 LUMNDS797-Dec0904 rev. A.0 2.5 Gbps Single Mode Transceiver C-1X-2500(C)-TDFB(3)-SSCX Ordering Information Available Options: C-13-2500-TDFB-SSC2 C-13-2500C-TDFB-SSC2 C-13-2500-TDFB3-SSC2 C-13-2500C-TDFB3-SSC2 C-15-2500-TDFB-SSC2 C-15-2500C-TDFB-SSC2 C-15-2500-TDFB3-SSC2 C-15-2500C-TDFB3-SSC2 C-13-2500-TDFB-SSC4 C-13-2500C-TDFB-SSC4 C-13-2500-TDFB3-SSC4 C-13-2500C-TDFB3-SSC4 C-15-2500-TDFB-SSC4 C-15-2500C-TDFB-SSC4 C-15-2500-TDFB3-SSC4 C-15-2500C-TDFB3-SSC4 Part numbering Definition: C - 1X - 2500(C) - TDFB(3) - S SC TxPower • 13 = Wavelength 1310nm 15 = Wavelength 1550nm • Communication protocol (2.5 Gbps) 2500 = PECL Signal Detection Output 2500C = TTL Signal Detection Output • TDFB = +5V Transceiver, DFB TDFB3= +3.3V Transceier, DFB • Single mode fiber • Connector options • Tx Power range 2 = -5 to 0 dBm 4 = 0 to +5 dBm Warnings: Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation. Legal Notes: IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale for further warranty information. LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. © LuminentOIC, Inc. 2003 All rights reserved LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 6 LUMNDS797-Dec0904 rev. A.0