Omron E3F2-R4B4F-P1 Photoelectric sensors e3f2 Datasheet

Photoelectric Sensors
E3F2
Threaded Cylindrical Photoelectric
Sensors with Built-in Amplifier for Use
as an Optical Proximity Switch
• M18 DIN-sized cylindrical housing
• Housing materials: plastic, nickel plated brass and stainless
steel
• Axial and radial types (with integrated 90°-optics)
• Enclosure rating IP67
• DC switching types with connectors for easy maintenance
• Full metal plug-in type
• Sensing distance separate types: 7 m, 10 m
• Retroreflective polarizing types: 2 m, 4 m
• Background suppression type: 10 cm
• Long detection distance (0.3 m, 1 m) with sensitivity adjuster for diffuse type
• Wide-beam characteristics (10 cm) for diffuse type
• Wide operating voltage range
(10 to 30 VDC or 24 to 240 VAC)
• Short-circuit and reverse connection protection
(DC switching type)
• UL and CSA approved (AC switching types)
• UL listed (DC switching types)
Photoelectric Sensors
E3F2
1
Ordering Information
■ DC-Switching Models
Housing Material: Plastic
Note: Shaded models are normally stocked.
Sensing method
Appearance
Multi purpose
Through-beam
pre-wired
Sensing
distance
7m
M12 connector
- precision detection (*1)
- test input
axial
Polarizing
(with MSR
function)
pre-wired
10 m
M12 connector
Non-polarizing
(without MSR function)
Retroreflective
(incl. reflector
E39-R1 or
E39-R1S)
Connection
method
pre-wired
M12 connector
Fixed
sensitivity
pre-wired
Adjustable
sensitivity
axial
M12 connector
NPN output
E3F2-7B4
E3F2-7C4
E3F2-7B4-P1
E3F2-7C4-P1
E3F2-10B4
E3F2-10C4
E3F2-10B4-P1
E3F2-10C4-P1
0.1 - 2 m(*2) E3F2-R2B4
E3F2-R2B4-P1
E3F2-R2C4
0.1 - 4 m(*3) E3F2-R4B4F
E3F2-R4B4F-P1
E3F2-R4C4F
E3F2-R2C4-P1
E3F2-R4C4F-P1
pre-wired
E3F2-R4B4
E3F2-R4C4
M12 connector
E3F2-R4B4-P1
E3F2-R4C4-P1
pre-wired
Polarizing
(with MSR function)
Model
PNP output
M12 connector
0.1 - 2 m(*2) E3F2-R2RB41
E3F2-R2RB41-P1
E3F2-R2RC41
E3F2-R2RC41-P1
radial
Fixed sensitivity
Wide-beam characteristics
M12 connector
Adjustable sensitivity
pre-wired
pre-wired
axial
Diffuse
reflective
0.1 m
0.3 m
M12 connector
pre-wired
1m
M12 connector
Adjustable sensitivity
pre-wired
0.3 m
M12 connector
E3F2-DS10B4-N
E3F2-DS10C4-N
E3F2-DS10B4-P1
E3F2-DS10C4-P1
E3F2-DS30B4
E3F2-DS30C4
E3F2-DS30B4-P1
E3F2-DS30C4-P1
E3F2-D1B4
E3F2-D1C4
E3F2-D1B4-P1
E3F2-D1C4-P1
E3F2-DS30B41
E3F2-DS30C41
E3F2-DS30B41-P1
E3F2-DS30C41-P1
E3F2-LS10B4
E3F2-LS10C4
E3F2-LS10B4-P1
E3F2-LS10C4-P1
radial
pre-wired
Fixed sensing distance
Background
suppression
M12 connector
10 cm
axial
*1) with slit E39-ES18
*2) with reflector E39-R1
*3) with reflector E39-R1S
Note: Standard cable length is 2 m. Models provided with a 5 m long cable are available. When ordering, specify the cable length by adding the
length of the cable (e.g. E3F2-R2RB4 2M or E3F2-R2RB4 5M). For other cable length please contact your OMRON sales representative.
2
Photoelectric Sensors
E3F2
■ Housing material: Metal (Nickel plated brass)
Note: Shaded models are normally stocked.
Sensing method
Appearance
Through-beam Multi purpose
Connection
method
pre-wired
Sensing
distance
7m
M12 connector
- precision detection
- test input
Retroreflective
(incl. reflector
E39-R1)
Polarizing
(with MSR
function)
pre-wired
axial
Fixed
sensitivity
M12 connector
pre-wired
M12 connector
pre-wired
Adjustable
sensitivity
axial
M12 connector
NPN output
E3F2-7B4-M
E3F2-7C4-M
E3F2-7B4-M1-M
E3F2-7C4-M1-M
E3F2-10B4-M
E3F2-10C4-M
E3F2-10B4-M1-M
E3F2-10C4-M1-M
0.1 - 2 m(*1) E3F2-R2RB4-M
E3F2-R2RB4-M1-M
0.1 - 4 m(*2) E3F2-R4B4F-M
E3F2-R4B4F-M1-M
E3F2-R2RC4-M
E3F2-R2RC4-M1-M
E3F2-R4C4F-M
E3F2-R4C4F-M1-M
pre-wired
E3F2-R4B4-M
E3F2-R4C4-M
M12 connector
E3F2-R4B4-M1-M
E3F2-R4C4-M1-M
pre-wired
Polarizing
(with MSR function)
10 m
Model
PNP output
0.1 - 2 m (*1) E3F2-R2RB41-M
E3F2-R2RC41-M
radial
Diffuse
reflective
pre-wired
Fixed sensing distance
Wide-beam characteristics
Adjustable sensing
distance
0.1 m
M12 connector
pre-wired
axial
0.3 m
M12 connector
pre-wired
1m
M12 connector
pre-wired
Adjustable sensing
distance
0.3 m
M12 connector
E3F2-DS10B4-M
E3F2-DS10C4-M
E3F2-DS10B4-M1-M
E3F2-DS10C4-M1-M
E3F2-DS30B4-M
E3F2-DS30C4-M
E3F2-DS30B4-M1-M
E3F2-DS30C4-M1-M
E3F2-D1B4-M
E3F2-D1C4-M
E3F2-D1B4-M1-M
E3F2-D1C4-M1-M
E3F2-DS30B41-M
E3F2-DS30C41-M
E3F2-DS30B41-M1-M
E3F2-DS30C41-M1-M
E3F2-LS10B4-M
E3F2-LS10C4-M
E3F2-LS10B4-M1-M
E3F2-LS10C4-M1-M
radial
Background
suppression
pre-wired
Fixed sensing
distance
M12 connector
10 cm
axial
*1) with reflector E39-R1
*2) with reflector E39-R1S
Note: Standard cable length is 2 m. Models provided with a 5 m long cable are available. When ordering, specify the cable length by adding the
length of the cable (e.g. E3F2-R2RB4 2M or E3F2-R2RB4 5M). For other cable length please contact your OMRON sales representative.
Photoelectric Sensors
E3F2
3
■ Housing material: Metal (Stainless steel)
Note: Shaded models are normally stocked.
Sensing method
Appearance
Through-beam
Connection
method
pre-wired
axial
Retroreflective
(incl. reflector
E39-R1)
Polarizing
(with MSR function)
Diffuse
reflective
Fixed sensitivity
Wide-beam characteristics
7m
M12 connector
pre-wired
M12 connector
axial
Adjustable sensitivity
Sensing
distance
pre-wired
0.1 m
pre-wired
0.3 m
M12 connector
NPN output
E3F2-7B4-S
E3F2-7C4-S
E3F2-7B4-M1-S
E3F2-7C4-M1-S
0.1 - 2 m E3F2-R2RB4-S
(with
E3F2-R2RB4-M1-S
reflector
E39-R1)
M12 connector
axial
Model
PNP output
E3F2-R2RC4-S
E3F2-R2RC4-M1-S
E3F2-DS10B4-S
E3F2-DS10C4-S
E3F2-DS10B4-M1-S
E3F2-DS10C4-M1-S
E3F2-DS30B4-S
E3F2-DS30C4-S
E3F2-DS30B4-M1-S
E3F2-DS30C4-M1-S
Note: Standard cable length is 2 m. Models provided with a 5 m long cable are available. When ordering, specify the cable length by adding the
length of the cable (e.g. E3F2-R2RB4-S 2M or E3F2-R2RB4-S 5M). For other cable length please contact your OMRON sales representative.
■ AC-Switching Models
Housing material: Plastic
Note: Shaded models are normally stocked.
Sensing method
Appearance
Through-beam
Connection
method
pre-wired
Sensing
distance
3m
Model
Light-ON
E3F2-3Z1
Dark-ON
E3F2-3Z2
axial
Retroreflective
(incl. reflector
E39-R1)
Non-polarizing
(without MSR function)
Diffuse
reflective
Fixed sensing distance
Wide-beam characteristics
pre-wired
axial
pre-wired
0.1 - 2 m E3F2-R2Z1
(with
reflector
E39-R1)
0.1 m
E3F2-DS10Z1-N
E3F2-R2Z2
E3F2-DS10Z2-N
axial
Note: Standard cable length is 2 m. Models provided with a 5 m long cable are available. When ordering, specify the cable length by adding the
length of the cable (e.g. E3F2-R2Z1 2M or E3F2-R2Z1 5M). For other cable length please contact your OMRON sales representative.
4
Photoelectric Sensors
E3F2
■ Accessories (Order Separately)
Note: Shaded models are normally stocked.
Name
Reflectors
Sensing distance (typical) [1.]
Model
Remark
0.1 - 3.7 m (axial)
0.1 - 2.4 m (radial)
E39-R1
60 x 40 mm (included in
some models)
0.1 - 4.3 m (axial)
E39-R1S
for E3F2-R4
0.1 - 4.2 m (axial)
0.1 - 2.7 m (radial)
E39-R7
84 mm
0.1 - 5.3 m (axial)
0.1 - 3.1 m (radial)
E39-R8
100 x 100 mm
0.1 - 4.3 m (axial)
E39-R40
80 x 80 mm
E39-RSA
35 x 10 mm
E39-RSB
35 x 40 mm
E39-RS3
80 x 70 mm
Tape Reflectors
Lens Cap
E39-F31
Mounting Bracket
Y92E-B18
screw mount
Y92E-G18
quick access mounting
E39-ES18
for E3F2-[email protected] - precision
detection
Slit
For detailed information about Accessories, refer to the main chapter “Accessories” at the end of the document.
Note: 1. Typical sensing distance corresponds to 80% of the max. sensing distance. For details, please refer to “Engineering Data”.
■ Sensor I/O Connectors
Note: Shaded models are normally stocked.
Cord
Shape
Standard
Straight
L-shaped
Vibration-proof
robot cable
Cable type
2m
Straight
L-shaped
Four-wire type
Model
XS2F-D421-D80-A
5m
XS2F-D421-G80-A
2m
XS2F-D422-D80-A
5m
XS2F-D422-G80-A
2m
XS2F-D421-D80-R
5m
XS2F-D421-G80-R
2m
XS2F-D422-D80-R
5m
XS2F-D422-G80-R
Photoelectric Sensors
E3F2
5
Specifications
■ Ratings / Characteristics of DC Switching Models
Item
[email protected]
Sensing method
Power supply voltage
Current consumption
Rated sensing distance
[1.]
[email protected] [email protected]@ [email protected] [email protected]@ [email protected] [email protected]
Through-beam
- multi
- Precision
purpose
detection [6.]
- test input
10 to 30 V DC 12 to 24 V DC
50 mA max.
7m
10 m
Typical sensing distance –
for different reflector
types (ref. to accessories) [2.]
Standard object
Directional angle
Differential travel
(hysteresis)
Black/white error
Response time
Control output
Power reset time
Ambient illumination
Ambient temperature
Ambient humidity
Insulation resistance
Dielectric strength
Vibration resistance
Shock resistance
Enclosure ratings
Light source
Indicators
Sensitivity adjustment
Connection method
Test Input
Operation mode
Weight (approx.)
Plastic pre-wired (2 m)
case
connector
Metal pre-wired (2 m)
case
connector
Circuit protection
Housing materials
Retroreflective
Nonpolarizing
4.0 m E39-R1:
3.7 m
4.5 m axial
5.3 m radial 2.4 m
E39-R7:
axial
4.2 m
radial 2.7 m
E39-R8:
axial
5.3 m
radial 3.1 m
Opaque: 56 mm dia. min.
E39-R1:
E39-R7:
E39-R8:
Opaque: 11 mm dia. min.
3° to 20°
–
Diffuse reflective
Wide beam
Adjustable sensing distance
characteristic
Polarizing
10 to 30 V DC
25 mA max.
30 mA max.
0.1 - 2 m
(with reflector E39-R1)
0.1 - 4 m
(with reflector
E39-R1S)
25 mA max.
0.1 m
(5 x 5 cm white
mat paper)
30 mA max.
0.3 m
(10 x 10 cm
white
mat paper)
1m
(30 x 30 cm
white
mat paper)
[email protected]@
Background
suppression
0.1 m
(10 x 10 cm
white
mat paper)
E39-R1S:4.3 m –
E39-R7: 4.8 m
E39-R8: 5.6 m
E39-R40: 4.3 m
E39-RS3: 2 m
–
–
20% max.
5% max
–
Operation and Reset: 2.5 ms max.
1 ms max
2.5 ms max.
Transistor (open collector), load current: 100 mA max. (residual voltage: 2 V max.)
50 ms
100 ms max.
50 ms
Incandescent lamp: 3000 lx max. / Sunlight: 10000 lx max.
Operating: -25 to 55 °C / Storage: -30 to 70 °C (with no icing or condensation)
Operating: 35% to 85% / Storage: 35% to 95% (without condensation)
20 MΩ min. at 500 V DC between energized parts and case
1000 VAC max., 50 / 60 Hz for 1 min between energized parts and case
10 to 55 Hz, 1.5 mm double amplitude for 2 hrs each direction (X, Y, Z)
Destruction: 500 m/s2 each direction (X, Y, Z)
IP67 [3.]; NEMA 1, 2, 4
Infrared LED (880 nm/850 nm)
[email protected]@
Red LED (660 nm)
3%
1 ms max.
100 ms
Red LED
(660 nm)
Light incident Output
Light incident / power
Light incident
Light incident / power indicator Light incident Output
/ power indi- (orange) /
indicator for light source (red)
(red) /
for light source (red)
(red) /
indicator
cator for light light emission
stability (green)
stability
(orange) / stasource (red) (red)
(green)
bility (green)
Fixed
Fixed /
Fixed
Adjustable
Fixed
Adjustable
2 m, 5 m pre-wired cable (PVC, dia. 4 mm (18 / 0.12) [4.]) or M12-connector
–
[7.]
–
Light-ON or Dark-ON selectable by wiring
120 g
60 g
40 g
20 g
180 g
90 g
120 g
50 g
Output short-circuit and power supply reverse polarity
Plastic (case: ABS; lens: PMMA)
Nickel brass Nickel brass –
Nickel brass
Stainless
–
–
Stainless
steel [5.]
steel [5.]
Nickel brass
–
Infrared LED (880 nm)
Nickel brass
Stainless
steel [5.]
Nickel brass
Stainless
steel [5.]
Nickel brass
–
Nickel brass
–
Note: 1. For stable sensing distance in detail, please refer to “Engineering Data”
2. Typical sensing distance corresponds to 80% of the max. sensing distance.
3. The enclosure rating IP67 of OMRON internal standards correspond to stricter test requirements than the standard IEC 60529 (refer to
chapter “Precautions”)
4. For other cable materials (e.g. PUR) please contact your OMRON sales representative.
5. Material-specification for stainless steel housing case: 1.4305 (W.-No.), 303 (AISI), 2346 (SS). For other stainless steel materials please
contact your OMRON sales representative.
6. with slit E39-ES18
7. PNP models -B4: VCC to VCC -2.5 V: Emitting OFF (Source current: 3 mA max.) / Open or 0 to 2.5 V: Emitting ON (Leakage current: 0.1
mA max.)
NPN models -C4: 0 to 2.5 V: Emitting OFF (Source current: 3 mA max.) / Open or Vcc to Vcc -2.5 V: Emitting ON (Leakage current: 0.1
mA max.)
6
Photoelectric Sensors
E3F2
■ Ratings / Characteristics of AC Switching Models
Item
Sensing method
E3F2-3Z1
E3F2-3Z2
Through-beam
E3F2-R2Z1
E3F2-R2Z2
Non-polarizing Retroreflective
E3F2-DS10Z1
E3F2-DS10Z2
Diffuse reflective
(wide-beam characteristic)
Power supply voltage
24 to 240 VAC ±10%, 50 / 60 Hz
Current consumption
10 mA max.
5 mA max.
Rated sensing distance[1.]
3m
0.1 - 2 m
(with reflector E39-R1)
0.1 m
(5 x 5 cm white mat paper)
Typical sensing distance for different reflector types [2.]
–
E39-R1: 3,4 m
E39-R7: 3,9 m
E39-R8: 5,2 m
–
Detectable object
Opaque object: 11 mm min.
Opaque object: 56 mm min.
Directional angle
3° to 20°
–
Differential travel
–
20% max.
Response time
30 ms max.
Control output
AC solid state (SCR) 200 mA max.; residual voltage: 5 V max. at 200 mA
Opaque objects
Power reset time
100 ms
Ambient illumination
Incandescent lamp: 3000 lx max. Sunlight: 10000 lx max.
Ambient temperature
Operating: -25 to 55 °C / Storage: -30 to 70 °C (with no icing or condensation)
Ambient humidity
Operating: 35% to 85% / Storage: 35% to 95% (without condensation)
Insulation resistance
20 MΩ min. at 500 V DC between energized parts and case
Dielectric strength
1500 VAC, 50 / 60 Hz for 1 min between energized parts and case
Vibration resistance
10 to 55 Hz, 1.5 mm double amplitude for 2 hrs each direction (X, Y, Z)
Shock resistance
500 m/sqr (approx. 50 g) for each direction (X, Y, Z)
Enclosure rating
IP67 [3.]; NEMA 1, 2, 4
Light source
Infrared LED (880 nm)
Indicators
Light incident/power indicator for light source (red)
Sensitivity adjustment
Fixed
Connection method
2 m, 5 m pre-wired cable (PVC dia. 4 mm (14 / 0.15))
Operation mode
Light-ON or Dark-ON (fixed)
Circuit protection
None
Weight (approx.)
110 g (pre-wired 2 m cable)
Housing materials
Plastic (case: ABS; lens: PMMA)
Note: 1. For stable sensing distance in detail, please refer to “Engineering Data”
2. Typical sensing distance corresponds to 80% of the max. sensing distance.
3. The enclosure rating IP67 of OMRON internal standards correspond to stricter test requirements than the standard IEC 60529 (refer to
chapter “Precautions”)
Photoelectric Sensors
E3F2
7
Engineering Data (Typical)
■ Operating Range (typical)
Through-beam Models (axial)
[email protected]@
Through-beam Models (axial)
[email protected]
Through-beam Models (axial)
[email protected]
500
300
typical sensing distance: 3.8 m
400
300
Distance Y (mm)
Distance Y (mm)
200
100
0
–100
-400
Y
X
0
200
1
2
3
300
5
0 1 2 3 4 5 6 7 8 9 10 11 12 13 1415 16 17
Distance X (m)
4
Distance X (m)
Retroreflective Models (axial)
[email protected]@ (polarizing)
and reflectors
200
typical sensing distances:
E39-R1: 3.4 m
E39-R7: 3.9 m
E39-R8: 5.2 m
200
Y
X
-500
Retroreflective Models (axial)
[email protected] (non polarizing)
and reflectors
typical sensing distances:
E39-R1: 4.0 m
E39-R7: 4.5 m
E39-R8: 5.3 m
0
-100
-300
–300
300
100
-200
–200
Retroreflective Models (axial)
[email protected]@ (non polarizing)
and reflectors
200
typical sensing distances:
E39-R1: 3.7 m
E39-R7: 4.2 m
E39-R8: 5.3 m
150
0
–100
Distance Y (mm)
Distance Y (mm)
Distance Y (mm)
100
100
100
0
–100
50
0
–50
–100
–200
–200
Reflector
Y
Y
X
–300
–300
0
1
2
3
4
5
6
7
8
0
1
2
3
4
Distance X (m)
200
6
7
8
Retroreflective Models (radial)
[email protected]@ (polarizing)
and reflectors
100
Typical sensing distance
E39-RS3
E39-R1S
E39-R40
E39-R7
E39-R8
typical sensing distances:
E39-R1: 2.4 m
E39-R7: 2.7 m
E39-R8: 3.1 m
50
100
Distance Y (mm)
Distance Y (mm)
150
5
50
0
- 50
- 100
0
–50
- 150
- 200
Y
Reflector
- 250
0
1
2
3
4
5
6
7
Reflector
–100
8
9
Distance X (m)
8
Y
X
X
Photoelectric Sensors
E3F2
0
0.5
1
1.5
2
2.5
3
–150
Y
3.5
4
Distance X (m)
Reflector
X
–200
Distance X (m)
Retro-reflective Models (axial)
[email protected]@[email protected] (polarizing)
250
Reflector
X
0
1
2
3
4
5
6
7
Distance X (m)
Diffuse reflective Models (axial)
[email protected]@ (wide-beam type)
Diffuse reflective Models (axial)
[email protected] (wide-beam type)
15
Diffuse reflective Models (axial)
[email protected]@
40
30
Sensitivity adjusted to maximum
Sensitivity adjusted to 400 mm
30
10
20
white paper
(50 x 50 mm)
0
–5
Distance Y (mm)
Distance Y (mm)
Distance Y (mm)
20
5
10
white paper
(50 x 50 mm)
0
–10
10
white paper
(100 x 100 mm)
0
–10
–20
–10
Sensing distance adjustable
between 0 and 550 mm
–20
Y
Object
Y
Object
–30
20
40
60
80
100
120
140
0
20
40
60
80
Distance X (mm)
Diffuse reflective Models (radial)
[email protected]@
Object
X
–40
–30
0
Y
X
X
–15
100
120
140
0
100
200
Distance X (mm)
300
400
500
600
Distance X (mm)
Diffuse reflective Models (axial)
[email protected]@
100
40
Sensitivity adjusted to 390 mm
80
White paper (90% reflectivity)
30
60
10
Sensing object:
100 x 100 mm
0
–10
Distance Y (mm)
Distance Y (mm)
20
40
20
Sensing object:
300 x 300 mm
0
-20
-40
–20
-60
–30
Y
Object
Y
-80
X
0
Object
X
–40
100
200
300
400
500
-100
0
200
400
600
800
1000
1200
1400
1600
Distance X (mm)
Distance X (mm)
■ Excess Gain Ratio vs. Distance (typical)
Through-beam Models (axial)
[email protected]@
Through-beam Models (axial)
[email protected]
Through-beam Models (axial)
[email protected]
100
100
10
relative Gain
10
Excess gain
Excess gain
100
1
1
0.1
0.1
0
2
4
6
8
10
12
Distance X (m)
10
1
0
1
2
3
4
5
6
7
0 1 2 3 4
5 6 7 8 9 10 11 12 13 14 15 16 17 18
Distance X (m)
Photoelectric Sensors
Distance [m]
E3F2
9
Retroreflective Models (axial)
[email protected]@ (non polarizing)
and reflectors
Retroreflective Models (axial)
[email protected] (non polarizing)
and reflectors
Retroreflective Models (axial)
[email protected]@ (polarizing)
and reflectors
10
10
10
reflector E39-R1
Excess gain
100
Excess gain
100
Excess gain
100
reflector E39-R1
1
1
0.1
0.1
1
2
3
4
5
6
7
0.1
0
8
1
2
3
4
5
6
7
0
1
2
3
Distance X (m)
Distance X (m)
Retroreflective Models (axial)
[email protected]@[email protected]
4
5
6
7
Distance X (m)
Retroreflective Models (radial)
[email protected]@ (polarizing)
and reflectors
100
100
Reflectors:
E39-RS3
E39-R1S
E39-R40
E39-R7
E39-R8
Excess gain
10
Excess Gain
reflector E39-R8
reflector E39-R8
reflector E39-R8
0
reflector E39-R7
1
reflector E39-R7
reflector E39-R7
reflector E39-R1
1
10
reflector E39-R1
1
reflector E39-R7
reflector E39-R8
0.1
0.1
0
2
4
6
8
10
0
1
2
3
Distance X (m)
Diffuse reflective Models (axial)
[email protected]@ (wide-beam type)
5
Diffuse reflective Models (axial)
[email protected] (wide-beam type)
Diffuse reflective Models (axial)
[email protected]@
100
100
100
White paper
(90% reflectivity)
Grey paper
(18% reflectivity)
10
Excess gain
Excess gain
10
1
Sensitivity adjusted to maximum
Sensing object:
100 x 100 mm
Sensing object:
50 x 50 mm
Sensing object:
50 x 50 mm
Excess gain
4
Distance X (m)
White paper
(90% reflectivity)
1
10
White paper
(90% reflectivity)
1
Grey paper
(18% reflectivity)
0.1
0.1
0
20
40
60
80
100
120
140
Distance X (mm)
10
Grey paper
(18% reflectivity)
Photoelectric Sensors
E3F2
0.1
0
50
100
150
200
Distance X (mm)
0
200
400
600
800
1000
Distance X (mm)
Diffuse reflective Models (radial)
[email protected]@
Diffuse reflective Models (axial)
[email protected]@
100
100
Sensing object:
100 x 100 mm
10
Excess gain
Excess gain
Sensitivity adjusted to 390 mm
White paper
(90% reflectivity)
1
10
1
Grey paper
(18% reflectivity)
0.1
0
100
200
300
400
0,1
500
0
0.5
1
1.5
Distance X (mm)
2
Distance(m)
■ Light spot vs.
sensing distance
■ Incline (left and right) ■ Incline (up and down)
Background suppression Models
[email protected]
Background suppression Models
[email protected]
20,00%
Sensing Distence movement (%)
4
2
Sensing Distence movement (%)
20,00%
6
Spot diameter(mm)
Background suppression Models
[email protected]
10,00%
0,00%
-10,00%
0
50
100
150
0,00%
-10,00%
-20,00%
-20,00%
0
10,00%
-40
-30
-20
-10
0
10
20
30
40
-40
-30
-20
-10
0
10
20
30
40
Incline Angle (˚)
Incline Angle (˚)
Distance(mm)
■ Object material vs. sensing distance
Background suppression Models
[email protected]
120,0
Sensing Distance(mm)
100,0
80,0
60,0
40,0
20,0
0,0
white
corrugated
paper
black
SUS
mirror
Photoelectric Sensors
E3F2
11
Operation
■ Output Circuits
Structure of Sensor I/O Connector
Classification
DC
Wire color
Brown
White
Blue
Black
Connector
pin No.
Use
1
Power supply
(+V)
2
Mode selection
Lon/Don
3
Power supply
(0 V)
1
2
3
4
XS2F-D42#-D80-#
XS2F-G42#-G80-#
Output
4
Brown
White
Blue
Black
■ PNP Output
Model
Output transistor
status
[email protected]@
(except for
[email protected] and
[email protected])
–
Timing chart
–
Connection
method
–
Output circuit
Through-beam emitter
Brown
10 to 30 VDC
1
Power
indicator
(red)
Main
circuit
Blue
3
0V
Connector Pin Arrangement
1
2
4
3
ON when light is
incident.
(Light-ON)
Incident
Interrupted
Output
indicator
(red)
Output
transistor
Load
(relay)
ON
OFF
ON
OFF
Connect the
pink (Pin 2 )
and brown
(Pin 1 ) cords or
open the pink
cord (Pin 2 ).
Light
indicator
Red
Brown
Stability
indicator*
10 to 30 VDC
1
ZD
Green
Black
4
Main
circuit
ZD: VZ = 36 V
Blue
100 mA
max.
Load
3
Operate
Release
0V
Pink
Mode selection
2
Connector Pin Arrangement
1
* Only on models
[email protected] and
[email protected]
ON when light is
interrupted. (DarkON)
Incident
Interrupted
Output
indicator
(red)
ON
OFF
Output
transistor
ON
OFF
Load
(relay)
Connect the
pink (Pin 2 )
and blue
(Pin 3 ) cords.
Light
indicator
Red
2
4
3
Brown
Stability
indicator*
10 to 30 VDC
1
Green
Black
4
Main
circuit
ZD: VZ = 36 V
Blue
100 mA
max.
3
Operate
Release
0V
Pink
2
Mode selection
Connector Pin Arrangement
* Only on models
[email protected] and
[email protected]
12
Photoelectric Sensors
E3F2
1
2
4
3
Load
Model
Output transistor
status
[email protected]
–
ON when light is
incident.
(Light-ON)
Timing chart
Connection
method
–
Test
input
ON
OFF
Light
emission
ON
OFF
Indicator
ON
OFF
Incident
Interrupted
Output
indicator
(orange)
ON
OFF
Output
transistor
ON
OFF
Load
(relay)
Output circuit
Through-beam emitter
Red
Connect the
pink (Pin 2 )
and brown
(Pin 1 ) cords or
open the pink
cord (Pin 2 ).
Brown
Output
indicator
10 to 30 VDC
1
ZD
Orange
Black
4
Main
circuit
ZD: VZ = 36 V
Blue
100 mA
max.
Load
3
Operate
Release
0V
Pink
Mode selection
2
Connector Pin Arrangement
1
2
4
3
ON when light is
interrupted. (DarkON)
Incident
Interrupted
Output
indicator
(orange)
ON
OFF
Output
transistor
ON
OFF
Connect the
pink (Pin 2 )
and blue
(Pin 3 ) cords.
Brown
Output
indicator
10 to 30 VDC
1
Orange
Black
4
Main
circuit
ZD: VZ = 36 V
Blue
100 mA
max.
Load
3
Load
(relay)
Operate
Release
0V
Pink
Mode selection
2
Connector Pin Arrangement
1
2
4
3
[email protected]
ON when light is
incident.
(Light-ON)
Incident
Interrupted
Output
indicator
(orange)
ON
OFF
Output
transistor
ON
OFF
Load
(relay)
Connect the
pink (Pin 2 )
and brown
(Pin 1 ) cords or
open the pink
cord (Pin 2 ).
Output
indicator
Orange
Brown
Stability
indicator*
10 to 30 VDC
1
ZD
Green
Black
4
Main
circuit
ZD: VZ = 36 V
Blue
100 mA
max.
Load
3
Operate
Release
0V
Pink
Mode selection
2
Connector Pin Arrangement
1
2
4
3
ON when light is
interrupted. (DarkON)
Incident
Interrupted
Output
indicator
(orange)
ON
OFF
Output
transistor
ON
OFF
Load
(relay)
Connect the
pink (Pin 2 )
and blue
(Pin 3 ) cords.
Output
indicator
Orange
Brown
Stability
indicator*
10 to 30 VDC
1
Green
Black
4
Main
circuit
ZD: VZ = 36 V
Blue
100 mA
max.
3
Operate
Release
Load
0V
Pink
2
Mode selection
Connector Pin Arrangement
1
2
4
3
Note: Terminal numbers for connector type.
Photoelectric Sensors
E3F2
13
■ NPN Output
Model
Output transistor
status
[email protected]@
(except for
[email protected] and
[email protected])
–
Timing chart
Connection
method
–
Output circuit
Through-beam emitter
Brown
10 to 30 VDC
1
Power
indicator
(red)
Main
circuit
Blue
3
0V
Connector Pin Arrangement
1
2
4
3
ON when light is
incident.
(Light-ON)
Incident
Interrupted
Output
indicator
(red)
ON
OFF
Output
transistor
ON
OFF
Load
(relay)
Connect the
pink (Pin 2 )
and brown
(Pin 1 ) cords or
open the pink
cord (Pin 2 ).
Output
indicator
Red
Output
indicator
(red)
ON
OFF
Output
transistor
ON
OFF
Load
(relay)
ON when light is
incident.
(Light-ON)
ON
OFF
Light
emission
ON
OFF
Indicator
ON
OFF
Incident
Interrupted
Output
indicator
(red)
ON
OFF
Output
transistor
ON
OFF
Load
(relay)
0V
Pink
Mode selection
2
Connector Pin Arrangement
Connect the
pink (Pin 2 )
and blue
(Pin 3 ) cords.
1
2
4
3
Brown
Stability
indicator*
Output
indicator
10 to 30 VDC
1
Green
Red
100 mA
max.
Black
4
Main
circuit
Load
Blue
3
0V
ZD: VZ = 36 V
Pink
Mode selection
2
Connector Pin Arrangement
–
Test
input
Blue
3
Operate
Release
–
Load
ZD: VZ = 36 V
1
* Only on models
[email protected] and
[email protected]
[email protected]
100 mA
max.
Black
4
Main
circuit
Operate
Release
Incident
Interrupted
10 to 30 VDC
1
Green
* Only on models
[email protected] and
[email protected]
ON when light is
interrupted. (DarkON)
Brown
Stability
indicator*
2
4
3
Through-beam emitter
Red
Connect the
pink (Pin 2 )
and brown
(Pin 1 ) cords or
open the pink
cord (Pin 2 ).
Brown
Light
indicator
10 to 30 VDC
1
Orange
Main
circuit
Load
100 mA
max.
Black
4
Blue
3
0V
ZD: VZ = 36 V
Pink
Mode selection
2
Operate
Release
Connector Pin Arrangement
1
2
4
3
ON when light is
interrupted. (DarkON)
Incident
Interrupted
Output
indicator
(orange)
ON
OFF
Output
transistor
ON
OFF
Connect the
pink (Pin 2 )
and blue
(Pin 3 ) cords.
Brown
Light
indicator
10 to 30 VDC
1
Orange
100 mA
max.
Black
4
Main
circuit
Load
Blue
3
0V
ZD: VZ = 36 V
Pink
Load
(relay)
Operate
Release
2
Connector Pin Arrangement
1
2
4
3
14
Photoelectric Sensors
E3F2
Mode selection
Model
Output transistor
status
[email protected]
ON when light is
incident.
(Light-ON)
Timing chart
Incident
Interrupted
Output
indicator
(red)
ON
OFF
Output
transistor
ON
OFF
Connection
method
Connect the
pink (Pin 2 )
and brown
(Pin 1 ) cords or
open the pink
cord (Pin 2 ).
Output circuit
Output
indicator
Orange
Brown
Stability
indicator*
10 to 30 VDC
1
Green
Main
circuit
Load
100 mA
max.
Black
4
Blue
3
0V
ZD: VZ = 36 V
Pink
Load
(relay)
Mode selection
2
Operate
Release
Connector Pin Arrangement
1
2
4
3
ON when light is
interrupted. (DarkON)
Incident
Interrupted
Output
indicator
(orange)
ON
OFF
Output
transistor
ON
OFF
Connect the
pink (Pin 2 )
and blue
(Pin 3 ) cords.
Output
indicator
Orange
Brown
Stability
indicator*
10 to 30 VDC
1
Green
100 mA
max.
Black
4
Main
circuit
Load
Blue
3
0V
ZD: VZ = 36 V
Pink
Operate
Release
Load
(relay)
Mode selection
2
Connector Pin Arrangement
1
2
4
3
Note: Terminal numbers for connector type.
■ AC Output
Model
Output transistor
status
E3F2-3LZ
–
Timing chart
–
Connection
method
–
Output circuit
Through-beam emitter
Brown
Power
indicator
(red)
Main
circuit
24 to 240 VAC
Blue
E3F2-3Z1
E3F2-R2Z1
E3F2-DS10Z1-N
ON when light is
incident.
(Light-ON)
–
Incident
Interrupted
Output
indicator
(red)
ON
OFF
Output
transistor
ON
OFF
Load
(relay)
E3F2-3Z2
E3F2-R2Z2
E3F2-DS10Z2-N
ON when light is
interrupted. (DarkON)
Brown
Light
indicator
Operate
Release
200 mA
max.
Red
Load
Black
–
Main
circuit
24 to 240 VAC
Blue
Incident
Interrupted
Output
indicator
(red)
ON
OFF
Output
transistor
ON
OFF
Load
(relay)
Operate
Release
Photoelectric Sensors
E3F2
15
Dimensions Note: All units are in millimeters unless otherwise indicated
■ DC-Switching Models, plastic, axial type
Cable type
Connector type
Without potentiometer
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected] –P1
[email protected]
[email protected]
[email protected]
[email protected]
5
5
Light indicator
4
M12x1 6g
16.6 dia
24
optical
area
24
22
6.2
22
optical
area
4.7 dia
6.2
4 dia
42.3
37
73
62
42.3
37
4.8 dia
16.4 dia
64.9
Light indicator
4
M18x1 6g
M18x1 6g
8
8
With potentiometer
[email protected]
[email protected]
4
8
Sensitivity adjustor
Light indicator
M18x1 6g
16
22
5
5
Photoelectric Sensors
E3F2
optical
area
Sensitivity adjustor
4
8
Light indicator
M18x1 6g
24
6.2
24
4.7 dia
22
6.2
16.4 dia
optical
area
M12x1 6g
73
62
49.3
42.3
37
4.8 dia
4 dia
64.9
49.3
42.3
37
16.6 dia
[email protected]
[email protected]
■ DC-Switching Models, plastic, radial type
Cable type
Connector type
Without potentiometer
[email protected]
5
5
Light indicator
6.9
4
24
13.2
optical
area
22
24
4.7 dia
22
4 dia
37
optical
area
16.4 dia
42.3
13.2
64.9
73
62
42.3
37
4.8 dia
M12x1 6g
16.6 dia
[email protected]
3.45
Light indicator
4
6.9
M18x1 6g
3.45
M18x1 6g
8
8
With potentiometer
4.7 dia
5
4
8
Sensitivity adjustor
Light indicator
24
22
3.45
6.9
optical
area
13.2
24
13.2
optical
area
M12x1 6g
73
62
49.3
42.3
37
22
4 dia
37
4.8 dia
16.4 dia
64.9
49.3
42.3
[email protected]
16.6 dia
[email protected]
5
Sensitivity adjustor
6.9
4
8
3.45
Light indicator
M18x1 6g
M18x1 6g
Photoelectric Sensors
E3F2
17
■ DC-Switching Models, metal (brass and stainless steel), axial type
Cable type
Connector type
Without potentiometer
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
76
4
4.8 dia
M12x1 6g
65.5
42.3
37
optical
area
24
6.2
27.7
24
4
Light indicator
6.2
optical
area
27.7
16.4 dia
4.8 dia
4 dia
64.9
42.3
37
16.4 dia
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
Light indicator
M18x1 6g
M18x1 6g
With potentiometer
[email protected]
[email protected]
[email protected]
37
Sensitivity adjustor
Light indicator
M18x1 6g
27.7
4
Sensitivity adjustor
Light indicator
M18x1 6g
18
Photoelectric Sensors
optical
area
E3F2
6.2
24
4.8 dia
16.4 dia
49.3
42.3
M12x1 6g
optical
area
27.7
6.2
4
[email protected]
76
65.5
4.8 dia
16.4 dia
64.9
49.3
42.3
37
[email protected]
4 dia
[email protected]
[email protected]
[email protected]
24
■ DC-Switching Models, metal (brass and stainless steel), radial type
Cable type
Connector type
Without potentiometer
[email protected]
76
65.5
42.3
37
13.2
16.4 dia
optical
area
24
27.7
6.2
24
4.8 dia
M12x1.6g
optical
area
27.7
4
[email protected]
4.8 dia
4 dia
64.9
42.3
37
[email protected]
16.4 dia
[email protected]
6.9
Light indicator
4
3.45
Light indicator
M18x1 6g
M18x1.6g
With potentiometer
[email protected] [email protected]
76
65.5
4.8 dia
37
24
6.9
4
27.7
13.2
13.2
24
optical
area
16.4 dia
49.3
42.3
optical
area
M12x1 6g
4.8 dia
27.7
64.9
49.3
42.3
37
[email protected]
4 dia
16.4 dia
[email protected]
Sensitivity adjustor
Light indicator
M18x1 6g
6.9
3.45
4
3.45
Sensitivity adjustor
Light indicator
M18x1 6g
■ AC-Switching Models, plastic, axial type
Cable type
Without potentiometer
[email protected]
[email protected]
[email protected]
90
8
67.3
62
5 dia.
M18 x 1 6g
24
3.1
Light indicator
16.8 dia.
22
3.1
optical zone
Photoelectric Sensors
E3F2
19
■ Accessories (Order Separately)
Reflectors
E39-R1
E39-R1S
E39-R3
29
Two, 3.5 dia.
6
4.5
3.4
40.3
34
3.4
R20
7.5
14˚
7
7
13.7
18.45
0.2
22.9
20
0.2
11
Adhesive tape side
22.5
59.9 52
8
Material, reflective
surface: acrylic
Rear surface: ABS
16
19.3
41.8
2.7
1.6
Material, reflective
surface: acrylic
Rear surface: ABS
2-M3
25.4
Two, 3.2 dia.
R25.4
34.8 38
3.4
34
1.2
10.1
2.6
1.2
10˚
Stainless steel
(SUS304)
E39-R8
E39-R7
9
7.4
100
92
84
4.5
92
100
for M3
for
E39-R40
8.7
84.5
77
77
84.5
for M3
Tape Reflectors
E39-RS3
E39-RSA
35
0.6
0.7
10
80
Reflecting
surface
4 x R1
70
Adhesive
tape
E39-RSB
40
0.7
35
4-R1 Adhesive tape side
4 x R1
20
Photoelectric Sensors
E3F2
Reflecting
surface
Adhesive
tape
Installation
Mounting Bracket
Y92E-B18
Lens Cap
E39-F31
Glass plate
Metal rim
Gasket
E3F2
4 max.
20 dia.
Note: Hexagon bolt: M5 x 32
Material: plastic
Mounting Bracket
Y92E-G18
30
M24x1.5
Two tightening nuts
30
Approx. 35
23.5
20.5
5
Sensor tightening nut
30
30
Slit (for precision detection with [email protected])
E39-ES18
16
1
21
4
Photoelectric Sensors
E3F2
21
Precautions
The E3F2 Photoelectric Sensor is not a safety component for ensuring the safety of people which is defined in EC directive (91/368/
EEC) and covered by separate European standards or by any other
regulations or standards.
When using the photoelectric sensor in the vicinity of an inverter
motor, ensure to connect the protective earth ground wire of the
motor to earth. Failure to ground the motor may result in malfunction
of the sensor.
■ Degree of protection
When you use the photoelectric sensor at temperatures exceeding
45°C, the load current must be within the described values as shown
in the figure below.
Heat shock: The Alternating, fast temperature changes between
-25°C and +55°C are executed for 5 cycles and 1 hour
for each temperature. Function and isolation are
checked.
Water proof: The sensors are submerged alternating in water of
+2°C and +55°C. 20 cycles with 1 hour for each temperature are executed. Function, water tightness and
electrical isolation are checked.
Do not expose the photoelectric sensor to excessive shock during
installation, keeping within IP 67 standards.
130
0
45
55
Operating temperature (˚C)
■ Installation
■ Wiring
If the input/output lines of the photoelectric sensor are placed in the
same conduit or duct as power lines or high-voltage lines, the photoelectric sensor could be induced to malfunction, or even be damaged
by electrical noise. Separate the wiring, or use shielded lines as
input/output lines to the photoelectric sensor.
Do not connect the black wire to the brown wire without a load. Direct
connection of these wires may damage the photoelectric sensor (AC
switching type).
Brown
Load
Sensor
24 to 240 VAC
Black
Blue
22
200
Load current (mA)
The E3F2 photoelectric sensors have a degree of protection rated
with IP67. In this case, the sensors have passed the OMRON heat
shock test before the IP67-test of IEC 60529 (submersion at 1m
water depth for 30 min). Afterwards the sensors have been tested
according to the OMRON waterproof test.
Photoelectric Sensors
E3F2
Do not exceed a torque of
• 2.0 Nm (20 kgf cm) when tightening mounting nuts for plastic
models
• 20.0 Nm (200 kgf cm) when tightening mounting nuts for metal
models
Certain Terms and Conditions of Sale
1. Offer; Acceptance. These terms and conditions (these "Terms") are deemed
part of all catalogs, manuals or other documents, whether electronic or in writing, relating to the sale of goods or services (collectively, the "Goods") by
Omron Electronics LLC and its subsidiary companies ("Seller"). Seller hereby
objects to any terms or conditions proposed in Buyer's purchase order or other
documents which are inconsistent with, or in addition to, these Terms. Please
contact your Omron representative to confirm any additional terms for sales
from your Omron company.
2. Prices. All prices stated are current, subject to change without notice by
Seller. Buyer agrees to pay the price in effect at time of shipment.
3. Discounts. Cash discounts, if any, will apply only on the net amount of
invoices sent to Buyer after deducting transportation charges, taxes and
duties, and will be allowed only if (i) the invoice is paid according to Seller's
payment terms and (ii) Buyer has no past due amounts owing to Seller.
4. Orders. Seller will accept no order less than $200 net billing.
5. Governmental Approvals. Buyer shall be responsible for, and shall bear all
costs involved in, obtaining any government approvals required for the importation or sale of the Goods.
6. Taxes. All taxes, duties and other governmental charges (other than general
real property and income taxes), including any interest or penalties thereon,
imposed directly or indirectly on Seller or required to be collected directly or
indirectly by Seller for the manufacture, production, sale, delivery, importation,
consumption or use of the Goods sold hereunder (including customs duties
and sales, excise, use, turnover and license taxes) shall be charged to and
remitted by Buyer to Seller.
7. Financial. If the financial position of Buyer at any time becomes unsatisfactory
to Seller, Seller reserves the right to stop shipments or require satisfactory
security or payment in advance. If Buyer fails to make payment or otherwise
comply with these Terms or any related agreement, Seller may (without liability
and in addition to other remedies) cancel any unshipped portion of Goods sold
hereunder and stop any Goods in transit until Buyer pays all amounts, including amounts payable hereunder, whether or not then due, which are owing to it
by Buyer. Buyer shall in any event remain liable for all unpaid accounts.
8. Cancellation; Etc. Orders are not subject to rescheduling or cancellation
unless Buyer indemnifies Seller fully against all costs or expenses arising in
connection therewith.
9. Force Majeure. Seller shall not be liable for any delay or failure in delivery
resulting from causes beyond its control, including earthquakes, fires, floods,
strikes or other labor disputes, shortage of labor or materials, accidents to
machinery, acts of sabotage, riots, delay in or lack of transportation or the
requirements of any government authority.
10. Shipping; Delivery. Unless otherwise expressly agreed in writing by Seller:
a. Shipments shall be by a carrier selected by Seller;
b. Such carrier shall act as the agent of Buyer and delivery to such carrier
shall constitute delivery to Buyer;
c. All sales and shipments of Goods shall be FOB shipping point (unless otherwise stated in writing by Seller), at which point title to and all risk of loss of
the Goods shall pass from Seller to Buyer, provided that Seller shall retain a
security interest in the Goods until the full purchase price is paid by Buyer;
d. Delivery and shipping dates are estimates only.
e. Seller will package Goods as it deems proper for protection against normal
handling and extra charges apply to special conditions.
11. Claims. Any claim by Buyer against Seller for shortage or damage to the
Goods occurring before delivery to the carrier must be presented in writing to
Seller within 30 days of receipt of shipment and include the original transportation bill signed by the carrier noting that the carrier received the Goods from
Seller in the condition claimed.
12. Warranties. (a) Exclusive Warranty. Seller's exclusive warranty is that the
Goods will be free from defects in materials and workmanship for a period of
twelve months from the date of sale by Seller (or such other period expressed
in writing by Seller). Seller disclaims all other warranties, express or implied.
(b) Limitations. SELLER MAKES NO WARRANTY OR REPRESENTATION,
EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE GOODS.
BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
GOODS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR
INTENDED USE. Seller further disclaims all warranties and responsibility of
any type for claims or expenses based on infringement by the Goods or otherwise of any intellectual property right. (c) Buyer Remedy. Seller's sole obligation hereunder shall be to replace (in the form originally shipped with Buyer
responsible for labor charges for removal or replacement thereof) the noncomplying Good or, at Seller's election, to repay or credit Buyer an amount
equal to the purchase price of the Good; provided that in no event shall Seller
be responsible for warranty, repair, indemnity or any other claims or expenses
regarding the Goods unless Seller's analysis confirms that the Goods were
properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any goods by
Buyer must be approved in writing by Seller before shipment. Seller shall not
be liable for the suitability or unsuitability or the results from the use of Goods
in combination with any electrical or electronic components, circuits, system
assemblies or any other materials or substances or environments. Any
advice, recommendations or information given orally or in writing, are not to be
construed as an amendment or addition to the above warranty.
13. Damage Limits; Etc. SELLER SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE
GOODS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY,
NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of
Seller exceed the individual price of the Good on which liability is asserted.
14. Indemnities. Buyer shall indemnify and hold harmless Seller, its affiliates and
its employees from and against all liabilities, losses, claims, costs and
expenses (including attorney's fees and expenses) related to any claim, investigation, litigation or proceeding (whether or not Seller is a party) which arises
or is alleged to arise from Buyer's acts or omissions under these Terms or in
any way with respect to the Goods. Without limiting the foregoing, Buyer (at
its own expense) shall indemnify and hold harmless Seller and defend or settle
any action brought against Seller to the extent that it is based on a claim that
any Good made to Buyer specifications infringed intellectual property rights of
another party.
15. Property; Confidentiality. The intellectual property embodied in the Goods is
the exclusive property of Seller and its affiliates and Buyer shall not attempt to
duplicate it in any way without the written permission of Seller. Notwithstanding any charges to Buyer for engineering or tooling, all engineering and tooling
shall remain the exclusive property of Seller. All information and materials
supplied by Seller to Buyer relating to the Goods are confidential and proprietary, and Buyer shall limit distribution thereof to its trusted employees and
strictly prevent disclosure to any third party.
16. Miscellaneous. (a) Waiver. No failure or delay by Seller in exercising any right
and no course of dealing between Buyer and Seller shall operate as a waiver
of rights by Seller. (b) Assignment. Buyer may not assign its rights hereunder
without Seller's written consent. (c) Amendment. These Terms constitute the
entire agreement between Buyer and Seller relating to the Goods, and no provision may be changed or waived unless in writing signed by the parties.
(d) Severability. If any provision hereof is rendered ineffective or invalid, such
provision shall not invalidate any other provision. (e) Setoff. Buyer shall have
no right to set off any amounts against the amount owing in respect of this
invoice. (f) As used herein, "including" means "including without limitation".
Certain Precautions on Specifications and Use
1. Suitability of Use. Seller shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Good in the
Buyer's application or use of the Good. At Buyer's request, Seller will provide
applicable third party certification documents identifying ratings and limitations
of use which apply to the Good. This information by itself is not sufficient for a
complete determination of the suitability of the Good in combination with the
end product, machine, system, or other application or use. The following are
some examples of applications for which particular attention must be given.
This is not intended to be an exhaustive list of all possible uses of this Good,
nor is it intended to imply that the uses listed may be suitable for this Good:
(i) Outdoor use, uses involving potential chemical contamination or electrical
interference, or conditions or uses not described in this document.
(ii) Energy control systems, combustion systems, railroad systems, aviation
systems, medical equipment, amusement machines, vehicles, safety
equipment, and installations subject to separate industry or government
regulations.
(iii) Systems, machines and equipment that could present a risk to life or
property. Please know and observe all prohibitions of use applicable to
this Good.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS
RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM
AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT
THE SELLER'S PRODUCT IS PROPERLY RATED AND INSTALLED FOR
THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
2. Programmable Products. Seller shall not be responsible for the user's pro
gramming of a programmable Good, or any consequence thereof.
3. Performance Data. Performance data given in this catalog is provided as a
guide for the user in determining suitability and does not constitute a warranty
It may represent the result of Seller's test conditions, and the user must corre
late it to actual application requirements. Actual performance is subject to the
Seller's Warranty and Limitations of Liability.
4. Change in Specifications. Product specifications and accessories may be
changed at any time based on improvements and other reasons. It is our prac
tice to change part numbers when published ratings or features are changed
or when significant construction changes are made. However, some specifica
tions of the Good may be changed without any notice. When in doubt, specia
part numbers may be assigned to fix or establish key specifications for you
application. Please consult with your Seller's representative at any time to con
firm actual specifications of purchased Good.
5. Errors and Omissions. The information in this catalog has been carefully
checked and is believed to be accurate; however, no responsibility is assumed
for clerical, typographical or proofreading errors, or omissions.
Photoelectric Sensors
E3F2
23
Complete “Terms and Conditions of Sale” for product purchase and use are on Omron’s website
at www.omron.com/oei – under the “About Us” tab, in the Legal Matters section.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
OMRON ELECTRONICS LLC
OMRON CANADA, INC.
OMRON ON-LINE
One Commerce Drive
Schaumburg, IL 60173
885 Milner Avenue
Toronto, Ontario M1B 5V8
847-843-7900
416-286-6465
Global - http://www.omron.com
USA - http://www.omron.com/oei
Canada - http://www.omron.ca
For US technical support or other inquiries:
800-556-6766
Cat. No. E224-E3-04
24
04/05
Photoelectric Sensors
E3F2
Specifications subject to change without notice
Printed in USA
Similar pages