VER : B_7 update : 2016.06.07 LED Power ALF240 SERIES 240 Watts KEY FEATURES IP65/67 Design for Indoor or Outdoor LED Installations Three In One Dimming Function (Just For IP67 Design) (2~10VDC & PWM Signal or resistance) Bulit-in Active PFC Function, PF>0.95 Free Air Convection High Reliability With Constant Current & Constant Voltage Output Voltage and Constant Current Level can Be Adjusted Through Internal Potentiometer LED Power Application 3-Year Product Warranty ELECTRICAL SPECIFICATIONS All specifications valid at normal input voltage, full load and +25°C after warm-up time unless otherwise stated. Model No. ALF240-12S ALF240-24S Max Output Wattage (W) Voltage 192W 240W Output Protection Isolation ALF240-54S 47-63 Hz Current (Full load) 3 A max. (115 VAC) / 1.5 A max. (230 VAC) Inrush Current (<2ms) 30 A max. (115 VAC) / 60 A max. (230 VAC) Leakage Current <0.5 mA max. Power Factor PF>0.97 (115 VAC) / PF>0.93 (230 VAC) at Full Load Voltage (V.DC.) 12V 24V 36V 48V 54V Constant Current Range (V.DC.) 6 ~ 12V 15 ~ 24V 18 ~ 36V 24 ~ 48V 36 ~ 54V Voltage Adjustment Range ±5% Voltage Accuracy ±2% Current (Convection) (A) max 16 10 6.66 5 4.44 Current Adjustment Range (A) 8 ~ 16 5 ~ 10 3.33 ~ 6.66 2.5 ~ 5 2.22 ~ 4.44 Line Regulation ±1% 91.5% 92% 91.5% Load Regulation ±1% Maximum Capacitive Load 470-23,000µF depending on model Ripple & Noise (max.) 200mVp-p Efficiency (typ.) (at 230 V.AC) 89% Hold-up Time 8 ms min. Switching Frequency 80 kHz Over Power Protection Auto recovery Over Voltage Protection Auto recovery Overt Temperature Protection Auto recovery Short Circuit Protection Auto recovery Input-Output (V.AC) 3000V Input-FG (V.AC) 1500V Output-FG .(V.AC) Operating Temperature Environment ALF240-48S 90-264 VAC or 120-370 VDC Frequency (Hz) Input ALF240-36S 90% 500V -25°C…+70°C (with derating) Storage Temperature -40°C…+85°C Temperature Coefficient ±0.02%/°C ( 0~50°C ) Humidity 95% RH MTBF >100,000 h @ 25°C (MIL-HDBK-217F) Vibration 10~500Hz, 5G 10min./1cycle, 60min. each along X, Y, Z axes. http://www.archcorp.com.tw TEL: +886-2-26989508 FAX: +886-2-26981319 -1- VER : B_7 update : 2016.06.07 LED Power ALF240 SERIES 240 Watts ELECTRICAL SPECIFICATIONS All specifications valid at normal input voltage, full load and +25°C after warm-up time unless otherwise stated. Model No. ALF240-12S ALF240-24S ALF240-36S ALF240-48S 8.35 x 2.76 x 1.5 Inches ( 212.2 x 70.0 x 38.0 mm ) Tolerance 0.5 mm Dimension (L x W x H) Physical Safety Weight 1010 g Cooling Method Free air convection Agency Approvals UL60950-1 , CE EMI EN 55022 (Conducted & Radiated Emission) EMC EMS (Noise Immunity) EN 55024 (Surge 4KV) Surge 2KV L-N, 4KV L N-FG ALF240-54S NOTE 1. Ripple & Noise are measured at 20MHz of bandwidth with 0.1uF & 47uF parallel capacitor. 2. It's recommended to add Varistor 14S471K at L / N input side in parallel. This series has IP65 and IP67, when you place order, please be noted as ordering Part No. Model No. Ordering Part No ALF240-12S ALF240-24S IP65 ALF240-12S-IP65 ALF240-24S-IP65 IP67 ALF240-12S-IP67 ALF240-24S-IP67 DERATING http://www.archcorp.com.tw TEL: +886-2-26989508 FAX: +886-2-26981319 ALF240-36S ALF240-48S ALF240-54S ALF240-36S-IP65 ALF240-48S-IP65 ALF150-700-IP65 ALF240-36S-IP67 ALF240-48S-IP67 ALF150-700-IP67 BLOCK DIAGRAM -2- VER : B_7 update : 2016.06.07 LED Power ALF240 SERIES MECHANICAL DIMENSION 240 Watts ( Top View ) IP65 Design IP67 Design ASSEMBLY INSTRUCTIONS *U Case T=2.5mm Customer screws into the length of the case no higher than 0.5mm (Namely screw length for load plate thickness plus 3.0mm http://www.archcorp.com.tw TEL: +886-2-26989508 FAX: +886-2-26981319 -3- VER : B_7 update : 2016.06.07 LED Power ALF240 SERIES 240 Watts DIMMING OPERATION Built-in 3 in 1 dimming function, IP67 rated. Output constant current level can be adjusted through output cable by connecting a 100K Ohm VR or 2~10Vdc or 10V PWM signal between DIM+ and DIMI. 2~10V dimming function for output current adjustment (typ.) 110.0% 100.0% 90.0% 80.0% 70.0% Io% 60.0% 50.0% 40.0% 30.0% 20.0% 10.0% 0.0% 2V II. 3V 4V 5V 6V DIM(V) 7V 8V 9V 10V 10V PWM signal for output current adjustment (typ.) : Frequency range:100Hz~3KHz 110.0% 100.0% 90.0% 80.0% 70.0% Io% 60.0% 50.0% 40.0% 30.0% 20.0% 10.0% 0.0% 20% 30% 40% 50% 60% 70% 80% 90% 100% DIM(PWM) III. It can control 10~100% output Current but http://www.archcorp.com.tw TEL: +886-2-26989508 FAX: +886-2-26981319 it must add 100K Ohm VR in parallel -4-