NPC APSG160E102MJB5S Conductive polymer aluminum solid capacitor Datasheet

CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Radial Lead
New!
●Super
low ESR, high ripple current capability
2,000 to 5,000 hours at 105℃
●Rated voltage : 16 to 20Vdc
●RoHS Compliant
●Halogen Free
●Endurance:
PSG
Downsized
PSF
◆SPECIFICATIONS
Items
Category
Temperature Range
Rated Voltage
Capacitance Tolerance
Surge Voltage
Leakage Current
Characteristics
-55 to +105℃
*Note
16 to 20Vdc
P20% (M)
Rated voltage(V)B1.15
I=0.2CV or 500μA, whichever is greater
Where, I : Leakage current (μA), C : Nominal capacitance (μF), V : Rated voltage (V)
Dissipation Factor
(tanδ)
0.12 max.
Low Temperature
Characteristics
(Max.Impedance Ratio)
Z(-25℃)/Z(+20℃)≦1.15
Z(-55℃)/Z(+20℃)≦1.25
Endurance
Bias Humidity Test
Surge Voltage Test
Failure Rate
(at 20℃, 120Hz)
(at 105℃)
(at 20℃ after 2 minutes)
(at 20℃, 120Hz)
(at 100kHz)
The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 5,000 hours
(20V : 2,000 hours) at 105℃.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦The initial specified value
ESR
≦150% of the initial specified value
Leakage current
≦The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjecting them to DC voltage at 60℃,
90 to 95% RH for 1,000 hours.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦The initial specified value
ESR
≦150% of the initial specified value
Leakage current
≦The initial specified value
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105℃ for 30 seconds
through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds.
Appearance
No significant damage
≦±20% of the initial value
Capacitance change
≦The initial specified value
D.F. (tanδ)
≦150% of the initial specified value
ESR
≦The initial specified value
Leakage current
0.5% per 1,000 hours maximum (Confidence level 60% at 105℃)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃.
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
(1/2)
CAT. No. E1001L
CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Radial Lead
New!
◆DIMENSIONS [mm]
●Terminal
Code : E
F05,F08,H06,H08
F±0.5
Size code F05
F08
H06
H08
φD
6.3
8.0
φd
0.45
0.6
F
2.5
3.5
φD'
D+0.5max.
L'
L+1.0max.
φD'
φd
Coated Case
L'
15min.
HB5
JB5
10.0
5.0
L+1.5max.
◆MARKING
EX) 16V150F
G 6D6
150
16V
4min.
F±0.5
HB5,JB5
φD'
φd
Coated Case
L'
15min.
4min.
◆PART NUMBERING SYSTEM
1
2
3
4
A PSG
5
6
7
8
9
10
11
12
E
13
14
15
16
17
M
18
S
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 150µF:151)
Lead forming·Taping code
Terminal code
Voltage code (ex. 16V:160,20V:200)
Series code
Category
Please refer to “Product code guide (conductive polymer type)”
◆STANDARD RATINGS
WV(Vdc)
16
20
Cap(µF)
150
270
270
470
560
820
1,000
120
φD×L (mm)
Case size
ESR
(mΩ max. /20℃, 100 k to 3 00kHz)
Rated ripple current
(mArms/105℃, 100kHz)
Part No.
6.3×5
6.3×8
8×6
8×8
8×11.5
10×11.5
10×11.5
6.3×5
20
15
22
16
14
12
12
20
3,200
3,800
3,300
4,000
4,970
5,400
5,400
3,200
APSG160E□□151MF05S
APSG160E□□271MF08S
APSG160E□□271MH06S
APSG160E□□471MH08S
APSG160E□□561MHB5S
APSG160E□□821MJB5S
APSG160E□□102MJB5S
APSG200E□□121MF05S
□□ : Enter the appropriate lead forming or taping code.
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
(2/2)
CAT. No. E1001L
Similar pages