Anpec APL5102-12A 150ma, 4ma quiescent current regulator Datasheet

APL5101/2
150mA, 4µA Quiescent Current Regulator
Features
General Description
•
•
The APL5101/2 are micro-power and ultra low dropout
linear regulators, which operate from 2V to 6V input volt-
•
•
•
•
•
•
•
•
•
Ultra Low Quiescent Current: 4µA
Ultra Low Dropout Voltage:
[email protected]/150mA
age and deliver up to 150mA. Typical dropout voltage is
only 200mV at 150mA loading. Designed for use in bat-
Fixed Output Voltages: 1.2V~3.5V,
Steps 100mV
tery-powered system, the low 4µA quiescent current
makes it an ideal choice. Design with an internal P-chan-
Guaranteed 150mA Output Current
Stable with 1µF Output Capacitor
nel MOSFET pass transistor, the APL5101/2 maintain a
low supply current, independent of the load current and
Ceramic Capacitor can be used
Current-Limit Protection
dropout voltage.
Other features include thermal-shutdown protection and
Controlled Short Circuit Current: 50mA
Build-in Thermal Protection
current limit protection to ensure specified output current
and controlled short-circuit current. The APL5101/2 regu-
SOT-23, SOT-23-5, and SOT-89 Packages
Lead Free and Green Devices Available
lators come in a miniature SOT-23, SOT-23-5, and SOT89 packages.
(RoHS Compliant)
Applications
•
•
•
Hand-Held Equipment
RTC or CMOS Backup Power
Battery Powered Equipment
Pin Configuration
SOT-23-5
V IN
VIN
1
GND
GND
2
SHDN
SHDN
3
5
SOT-23
V OUT
VOUT
VOUT
V OUT
VVIN
IN
3
4
NC
NC
GND
GND
2
APL5101
APL5101
SOT-23
SOT-89
GND
GND
V
OUT
VOUT
SOT-23-5
1
3
GND VIN
V IN
1
2
V
IN
VIN
V IN
VIN
1
GND
GND
2
SHDN
NC
3
5
VOUT
V OUT
4
NC
NC
VOUT
VOUT
APL5101
APL5102
APL5102
ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise
customers to obtain the latest version of relevant information to verify before placing orders.
Copyright  ANPEC Electronics Corp.
Rev. A.5 - Jul., 2013
1
www.anpec.com.tw
APL5101/2
Ordering and Marking Information
Package Code
A : SOT-23
B : SOT-23-5
Operating Ambient Temperature Range
I : -40 to 85 oC
Handling Code
TR : Tape & Reel
Voltage Code :
12 : 1.2V ~ 35 : 3.5V
Assembly Material
L : Lead Free Device
G: Halogen and Lead Free Device
APL5101/2 Assembly Material
Handling Code
Temperature Range
Package Code
Voltage Code
D : SOT-89
APL5101 -12 A/B:
105X
X - Date Code : 5 - 1.2V
APL5101 -12 D :
APL5101 XXXXX - Date Code : 12 - 1.2V
XXXXX12
APL5102 -12 A/B:
AB5X
X - Date Code : 5 - 1.2V
APL5102 -12 D :
APL5102
XXXXX - Date Code : 12 - 1.2V
XXXXX12
Note: ANPEC lead-free products contain molding compounds/die attach materials and 100% matte tin plate termination finish; which
are fully compliant with RoHS. ANPEC lead-free products meet or exceed the lead-free requirements of IPC/JEDEC J-STD-020D for
MSL classification at lead-free peak reflow temperature. ANPEC defines “Green” to mean lead-free (RoHS compliant) and halogen
free (Br or Cl does not exceed 900ppm by weight in homogeneous material and total of Br and Cl does not exceed 1500ppm by
weight).
SOT-23 and SOT-23-5 packages
Product Name
APL5101-12A/B
APL5101-13A/B
APL5101-14A/B
APL5101-15A/B
APL5101-16A/B
APL5101-17A/B
APL5101-18A/B
APL5101-19A/B
APL5101-20A/B
APL5101-21A/B
APL5101-22A/B
APL5101-23A/B
APL5101-24A/B
APL5101-25A/B
APL5101-26A/B
APL5101-27A/B
APL5101-28A/B
APL5101-29A/B
APL5101-30A/B
APL5101-31A/B
APL5101-32A/B
APL5101-33A/B
APL5101-34A/B
APL5101-35A/B
Marking
105X
107X
108X
109X
10AX
10BX
10CX
10DX
10EX
10FX
10GX
10HX
10IX
10JX
10KX
10LX
10MX
10NX
10OX
10PX
10QX
10RX
10SX
10TX
Copyright  ANPEC Electronics Corp.
Rev. A.5 - Jul., 2013
Product Name
APL5102-12A/B
APL5102-13A/B
APL5102-14A/B
APL5102-15A/B
APL5102-16A/B
APL5102-17A/B
APL5102-18A/B
APL5102-19A/B
APL5102-20A/B
APL5102-21A/B
APL5102-22A/B
APL5102-23A/B
APL5102-24A/B
APL5102-25A/B
APL5102-26A/B
APL5102-27A/B
APL5102-28A/B
APL5102-29A/B
APL5102-30A/B
APL5102-31A/B
APL5102-32A/B
APL5102-33A/B
APL5102-34A/B
APL5102-35A/B
2
Marking
AB5X
AB7X
AB8X
AB9X
ABAX
ABBX
ABCX
ABDX
ABEX
ABFX
ABGX
ABHX
ABIX
ABJX
ABKX
ABLX
ABMX
ABNX
ABOX
ABPX
ABQX
ABRX
ABSX
ABTX
www.anpec.com.tw
APL5101/2
Absolute Maximum Ratings
Symbol
Parameter
Rating
Unit
VIN,VOUT
Input Voltage or Out Voltage
6.5
V
SHDN
VOUT Shutdown Control Pin
6.5
V
Thermal Resistance-Junction to Ambient
RTH,JA
SOT-23
SOT-23-5
SOT-89
260
260
180
SOT-23
SOT-23-5
SOT-89
130
130
90
°C /W
Thermal Resistance-Junction to Ambient
RTH,JC
PD
Power Dissipation
TJ
TSTG
TL
°C /W
Internally Limited
W
Junction Temperature Range
-40 to 150
°C
Storage Temperature Range
-65 to +150
°C
260
°C
Maximum Lead Soldering Temperature, 10 Seconds
Electrical Characteristics
Unless otherwise noted these specificatons apply over full temperature, VIN = 5V, CIN = COUT = 1µF, TA = -40 to 85°C. Typical values
refer to TA = 25°C.
APL5101/2
Symbol
VIN
Parameter
Test Conditions
Typ.
Max.
2
-
6
V
VIN = 5V
-2
-
2
%
1.2
-
3.5
V
VIN = 5V
250
300
370
mA
IOUT = 0mA
-
4
7
IOUT = 150mA
-
4
10
Input Voltage
Output Voltage Accuracy
VOUT
Output Voltage Range
ILIMIT
Current-Limit
Unit
Min.
Quiescent Current
IQ
Shutdown Supply Current
IOUT
VSHDN = High
Load Current
µA
-
0.1
1
150
-
-
mA
REGLINE
Line Regulation
VOUT + 0.5V<VIN<6V, IOUT = 10mA
-
2
10
mV
REGLOAD
Load Regulation
VIN = 5V, 0Ma<IOUT<IMAX
-
15
30
mV
VOUT
= 1.4V, IOUT = 150mA
-
1000
1300
VOUT
= 1.8V, IOUT = 150mA
-
600
900
VOUT
= 3.3V, IOUT = 150mA
-
200
300
30
40
-
dB
-
55
-
mA
VDROP
Dropout Voltage
(Note)
PSRR
Ripple Rejection
F = 1kHz, COUT = 1µF, IOUT = 10mA
ISHORT
Short Circuit Current
VOUT = 0V
Copyright  ANPEC Electronics Corp.
Rev. A.5 - Jul., 2013
3
mV
www.anpec.com.tw
APL5101/2
Electrical Characteristics (Cont.)
Unless otherwise noted these specificatons apply over full temperature, VIN = 5V, CIN = COUT = 1µF, TA = -40 to 85°C. Typical values
refer to TA = 25°C.
APL5101/2
Symbol
en
ISHDN
VSHDN
TEXIT
OTS
TC
Parameter
Test Conditions
Noise
F = 22Hz to 80kHz,
COUT = 1µF, IOUT = 10mA
Shutdown Input Bias Current
VSHDN = Low
Unit
Min.
Typ.
Max.
-
200
250
µVRMS
-
0.1
1
µA
High Threshold Voltage
1.6
-
VIN+0.3
V
Low Threshold Voltage
-0.3
-
0.4
V
1.5
2
2.5
mS
Over Temperature Shutdown
120
135
-
°C
Over Temperature Shutdown
Hysteresis
10
20
30
°C
-
100
200
ppm/°C
Output Capacitor
1
-
10
µF
ESR
10
-
1000
mΩ
Shutdown Exit Delay
VOUT = 90%, RLOAD = 25Ω
Output Voltage Temperature
Coefficient
TA = -40°C ~ 100°C
COUT
Note: Dropout voltage definition:VIN-VOUT when VOUT is 2% below the value of VOUT for VIN= VOUT+1V.
Pin Description
PIN
I/O
NO.
NAME
1
VIN
2
GND
3
SHDN
4
NC
5
VOUT
I
FUNCTION
Voltage supply input pin
GND pin
I
Shutdown control pin, high = off, low = normal
Not connected
O
Regulator output pin
Block Diagram
V IN
Current
L imit
SHD N
Shutdown
L o g ic
R e ference
V o lta g e
_
+
V O UT
Thermal
Shutdown
APL5101/2
Copyright  ANPEC Electronics Corp.
Rev. A.5 - Jul., 2013
4
G ND
www.anpec.com.tw
APL5101/2
Typical Application Circuit
APL5101/2
VIN
VOUT
SHDN
CIN
1µ F
COUT
1µ F
GND
Typical Operating Characteristics
Quiescent Current vs. Input Voltage
Quiescent Current vs. Output Current
5
4
VOUT=3.3V
4.5
3.5
VIN=5V
Quiescent Current(µA)
Quiescent Current(µA)
4
3.5
3
2.5
2
1.5
1
3
2.5
2
1.5
1
0.5
0.5
0
0
0
1
2
3
4
5
0
6
Input Voltage(V)
Copyright  ANPEC Electronics Corp.
Rev. A.5 - Jul., 2013
25
50
75
100
125
150
Output Current(mA)
5
www.anpec.com.tw
APL5101/2
Typical Operating Characteristics (Cont.)
Output Voltage vs. Input Voltage
Quiescent Current vs. Ambient Temperature
4
3.5
3.5
IOUT=0mA
VOUT=1.4V
Quiescent Current(µA)
Output Vlotage(V)
3
2.5
2
1.5
1
0.5
3
2.5
2
1.5
1
0.5
0
-40
0
0
1
2
3
4
5
6
-20
Input Voltage(V)
20
40
60
80
100
Ambient Temperature(°C)
Dropout Voltage vs. Output Current
PSRR vs. Frequency
+0
1200
-10 TTT
1000
100mA
T
-20
-30
VOUT=1.2V
800
PSRR(dB)
Dropout Voltage(mV)
0
600
400
50mA
-40
-50
-60
1mA
-70
-80
VOUT=3.3V
200
-90
-100
10
0
0
25
50
75
100
125
150
1k
10k
100k
Frequency(Hz)
Output Current(mA)
Copyright  ANPEC Electronics Corp.
Rev. A.5 - Jul., 2013
100
6
www.anpec.com.tw
APL5101/2
Typical Operating Characteristics (Cont.)
Load Transient Response
Load Transient Response
VOUT=1.4V
(50mV/div)
VOUT=3.3V
(50mV/div)
IL=1~150mA
IL=1~150mA
Time(0.5ms/div)
Time(0.5ms/div)
Line Transient Response
Line Transient Response
VIN(4.5V~5.5V)
VIN(4.5V~5.5V)
VOUT=1.4V(200mV/div)
IOUT=10mA
COUT=1µF
VOUT=3.3V(200mV/div)
IOUT=10mA
COUT=1µF
Time(0.1ms/div)
Time(0.1ms/div)
Copyright  ANPEC Electronics Corp.
Rev. A.5 - Jul., 2013
7
www.anpec.com.tw
APL5101/2
Typical Operating Characteristics (Cont.)
Current Limit vs. Input Voltage
Output Voltage vs. Ambient Temperature
1.398
400
VOUT(1.4V), TA=25°C
VOUT(3.3V), TA=25°C
350
1.396
250
VOUT(1.4V), TA=85°C
Output Volatge(V)
Current Limit(mA)
300
VOUT(3.3V), TA=85°C
200
150
IL=0mA
1.394
1.392
1.39
1.388
100
1.386
50
0
2.5
3
3.5
4
4.5
5
5.5
1.384
-40
6
Input Volatge(V)
-20
0
20
40
60
80
100
120
Ambient Temperature(°C)
Power Dissipation vs. Ambient Temperature
Output Voltage vs. Temperature
3.312
0.6
3.31
0.5
IL=0mA
Power Dissipation(W)
Output Voltage(V)
3.308
3.306
3.304
3.302
3.3
0.4
SOT-89
0.3
0.2
SOT-23
0.1
3.298
3.296
0
-40
-20
0
20
40
60
80
100
120
25
Copyright  ANPEC Electronics Corp.
Rev. A.5 - Jul., 2013
50
75
100
125
Ambient Temperature(°C)
Ambient Temperature(°C)
8
www.anpec.com.tw
APL5101/2
Application Information
Capacitor Selection and Regulation Stability
Operating Region and Power Dissipation
The APL5101/2 use at least a 1µF capacitor on the input.
The thermal resistance of the case and circuit board,
This capacitor can use Aluminum, Tantalum or Ceramic
capacitors. Input capacitor with large value and low ESR
ambient and junction air temperature, and the rate of air
flow all control the APL5101/2’s maximum power
provides better PSRR and line transient response. The
output capacitor also can use Aluminum, Tantalum or
dissipation. The power dissipation across the device is
P = IOUT (VIN-VOUT). The maximum power dissipation is:
Ceramic capacitor, and its proper values is recommended
1µF, ESR must be above 10mΩ Large output capacitor
PMAX = (TJ-TA) / (θJC +θCA )
where TJ-TA is the temperature difference between the
values can reduce noise and improve load-transient
response, stability, and PSRR. W ith X5R and Y5V
junction and ambient air. θJC is the thermal resistance of
the package, θCA is the thermal resistance through the
dielectrics, 1µF is sufficient at all operating temperatures.
The selection of output capacitor is important because it with
printed circuit board, copper traces, and other materials
to the surrounding air. The GND pin provides an electrical
COUT forms a zero to provide the sufficient phase margin.
connection to ground and channeling heat away. The
printed circuit board (PCB) forms a heat sink and dissi-
Input-Output (Dropout) Voltage
pates most of the heat into ambient air.
The minimum input-output voltage differential (dropout)
determines the lowest usable supply voltage. The drop-
Recommanded Minimum Footprint
out voltage is the function of drain-to-source on resistance multiplied by the load current.
SOT-23
0.037
0.057
Current Limit and Short Circuit
APL5101/2 include a current-limit circuitry for this linear regulator. The current limit protection, which sense
0.102
0.024
the current flows the P-channel MOSFET, and controls
the output voltage. The point where limiting occurs is
I OUT=300mA. W hen output is shorted to ground, the
APL5101/2 will keep short circuit current at 50mA.This
design is a method for an indefinite amount of time without damaging to the part.
0.074
Unit : Inch
Thermal Protection
SOT-23-5
Thermal protection limits total power dissipation in the
APL5101/2. When the junction temperature exceeds TJ =
+135°C, the thermal sensor generate a logic signal to turn
0.076
off the pass transistor and let IC to cool. When the IC’s
junction temperature cools by 20°C, the thermal sen0.1
sor will turn the pass transistor on again, resulting in a
pulsed output during continuous thermal protection. Ther-
0.05
mal protection is designed to protect the IC in the event of
fault conditions. For continual operation, the junction temperature do not exceed TJ=+125oC.
0.038
0.02
Unit : Inch
Copyright  ANPEC Electronics Corp.
Rev. A.5 - Jul., 2013
9
www.anpec.com.tw
APL5101/2
Application Information (Cont.)
Recommanded Minimum Footprint (Cont.)
SOT-89
0.067
0.104
0.140
0.076
0.059
0.022
Unit : Inch
Copyright  ANPEC Electronics Corp.
Rev. A.5 - Jul., 2013
10
www.anpec.com.tw
APL5101/2
Package Information
SOT-23
D
e
E
E1
SEE
VIEW A
c
b
0.25
A
L
GAUGE PLANE
SEATING PLANE
0
A1
A2
e1
VIEW A
S
Y
M
B
O
L
SOT-23
INCHES
MILLIMETERS
MIN.
MAX.
A
MIN.
MAX.
1.45
0.057
A1
0.00
0.15
0.000
A2
0.90
1.30
0.035
0.051
b
0.30
0.50
0.012
0.020
c
0.08
0.22
0.003
0.009
D
2.70
3.10
0.106
0.122
E
2.60
3.00
0.102
0.118
E1
1.40
1.80
0.055
0.071
e
0.95 BSC
e1
1.90 BSC
0.006
0.037 BSC
0.075 BSC
L
0.30
0.60
0
0°
8°
0.012
0°
0.024
8°
Note : Dimension D and E1 do not include mold flash, protrusions or gate
burrs. Mold flash, protrusion or gate burrs shall not exceed 10 mil
per side.
Copyright  ANPEC Electronics Corp.
Rev. A.5 - Jul., 2013
11
www.anpec.com.tw
APL5101/2
Package Information
SOT-23-5
D
e
E
E1
SEE
VIEW A
b
c
0.25
A
L
0
GAUGE PLANE
SEATING PLANE
A1
A2
e1
VIEW A
S
Y
M
B
O
L
SOT-23-5
MILLIMETERS
MIN.
INCHES
MAX.
MIN.
MAX.
A
0.057
1.45
A1
0.00
0.15
0.000
0.006
A2
0.90
1.30
0.035
0.051
b
0.30
0.50
0.012
0.020
c
0.08
0.22
0.003
0.009
0.122
D
2.70
3.10
0.016
E
2.60
3.00
0.102
0.118
1.80
0.055
0.071
E1
1.40
e
0.95 BSC
e1
0.037 BSC
1.90 BSC
0.075 BSC
L
0.30
0.60
0
0°
8°
0.012
0°
0.024
8°
Note : 1. Follow JEDEC TO-178 AA.
2. Dimension D and E1 do not include mold flash, protrusions or gate
burrs. Mold flash, protrusion or gate burrs shall not exceed 10 mil
per side.
Copyright  ANPEC Electronics Corp.
Rev. A.5 - Jul., 2013
12
www.anpec.com.tw
APL5101/2
Package Information
SOT-89
A
C
L
H
E
E1
D
D1
e
e1
B
B1
S
Y
M
B
O
L
A
SOT-89
MILLIMETERS
INCHES
MIN.
MAX.
MIN.
MAX.
1.40
1.60
0.055
0.063
B
0.44
0.56
0.017
0.022
B1
0.36
0.48
0.014
0.019
0.017
C
0.35
0.44
0.014
D
4.40
4.60
0.173
0.181
D1
1.62
1.83
0.064
0.072
E
2.29
2.60
0.090
0.102
E1
2.13
2.29
0.084
0.090
e
1.50 BSC
e1
3.00 BSC
0.059 BSC
0.118 BSC
H
3.94
4.25
0.155
0.167
L
0.89
1.20
0.035
0.047
Note : Follow JEDEC TO-243 AA.
Copyright  ANPEC Electronics Corp.
Rev. A.5 - Jul., 2013
13
www.anpec.com.tw
APL5101/2
Carrier Tape & Reel Dimensions
P0
P2
P1
A
B0
W
F
E1
OD0
K0
A0
A
OD1 B
B
T
SECTION A-A
SECTION B-B
H
A
d
T1
Application
SOT-23-3
Application
SOT-23-5
Application
SOT-89
A
H
178.0±
2.00
50 MIN.
P0
P1
4.0±0.10
4.0±0.10
A
H
178.0±
2.00
50 MIN.
P0
P1
4.0±0.10
4.0±0.10
A
H
178.0±
2.00
50 MIN.
P0
P1
4.0±0.10
8.0±0.10
T1
C
8.4+2.00 13.0+0.50
-0.00
-0.20
d
D
1.5 MIN.
20.2 MIN.
P2
D0
D1
T
2.0±0.05
1.5+0.10
-0.00
1.0 MIN.
0.6+0.00
-0.40
T1
C
d
D
1.5 MIN.
20.2 MIN.
8.4+2.00 13.0+0.50
-0.00
-0.20
P2
D0
D1
T
2.0±0.05
1.5+0.10
-0.00
1.0 MIN.
0.6+0.00
-0.40
T1
C
d
D
12.4+2.00 13.0+0.50
-0.00
-0.20
P2
D0
2.0±0.05
1.5+0.10
-0.00
1.5 MIN.
W
E1
8.0±0.30 1.75±
0.10
A0
B0
F
3.5±0.05
K0
3.20±0.20 3.10±
0.20 1.50±0.20
W
E1
8.0±0.30 1.75±
0.10
A0
B0
F
3.5±0.05
K0
3.20±0.20 3.10±
0.20 1.50±0.20
W
E1
F
20.2 MIN. 12.0±0.30 1.75±
0.10 5.50±0.05
D1
T
1.5 MIN.
0.6+0.00
-0.40
A0
B0
K0
4.80±0.20 4.50±
0.20 1.80±0.20
(mm)
Copyright  ANPEC Electronics Corp.
Rev. A.5 - Jul., 2013
14
www.anpec.com.tw
APL5101/2
Devices Per Unit
Package Type
SOT-23-3
SOT-23-5
SOT-89
Unit
Tape & Reel
Tape & Reel
Tape & Reel
Quantity
3000
3000
1000
Taping Direction Information
SOT-23-3
USER DIRECTION OF FEED
SOT-23-5
USER DIRECTION OF FEED
SOT-89
USER DIRECTION OF FEED
Copyright  ANPEC Electronics Corp.
Rev. A.5 - Jul., 2013
15
www.anpec.com.tw
APL5101/2
Classification Profile
Copyright  ANPEC Electronics Corp.
Rev. A.5 - Jul., 2013
16
www.anpec.com.tw
APL5101/2
Classification Reflow Profiles
Profile Feature
Sn-Pb Eutectic Assembly
Pb-Free Assembly
100 °C
150 °C
60-120 seconds
150 °C
200 °C
60-120 seconds
3 °C/second max.
3°C/second max.
183 °C
60-150 seconds
217 °C
60-150 seconds
See Classification Temp in table 1
See Classification Temp in table 2
Time (tP)** within 5°C of the specified
classification temperature (Tc)
20** seconds
30** seconds
Average ramp-down rate (Tp to Tsmax)
6 °C/second max.
6 °C/second max.
6 minutes max.
8 minutes max.
Preheat & Soak
Temperature min (Tsmin)
Temperature max (Tsmax)
Time (Tsmin to Tsmax) (ts)
Average ramp-up rate
(Tsmax to TP)
Liquidous temperature (TL)
Time at liquidous (tL)
Peak package body Temperature
(Tp)*
Time 25°C to peak temperature
* Tolerance for peak profile Temperature (Tp) is defined as a supplier minimum and a user maximum.
** Tolerance for time at peak profile temperature (tp) is defined as a supplier minimum and a user maximum.
Table 1. SnPb Eutectic Process – Classification Temperatures (Tc)
3
Package
Thickness
<2.5 mm
Volume mm
<350
235 °C
Volume mm
≥350
220 °C
≥2.5 mm
220 °C
220 °C
3
Table 2. Pb-free Process – Classification Temperatures (Tc)
Package
Thickness
<1.6 mm
1.6 mm – 2.5 mm
≥2.5 mm
Volume mm
<350
260 °C
260 °C
250 °C
3
Volume mm
350-2000
260 °C
250 °C
245 °C
3
Volume mm
>2000
260 °C
245 °C
245 °C
3
Reliability Test Program
Test item
SOLDERABILITY
HOLT
PCT
TCT
HBM
MM
Latch-Up
Method
JESD-22, B102
JESD-22, A108
JESD-22, A102
JESD-22, A104
MIL-STD-883-3015.7
JESD-22, A115
JESD 78
Copyright  ANPEC Electronics Corp.
Rev. A.5 - Jul., 2013
17
Description
5 Sec, 245°C
1000 Hrs, Bias @ Tj=125°C
168 Hrs, 100%RH, 2atm, 121°C
500 Cycles, -65°C~150°C
VHBM≧2KV
VMM≧200V
10ms, 1tr≧100mA
www.anpec.com.tw
APL5101/2
Customer Service
Anpec Electronics Corp.
Head Office :
No.6, Dusing 1st Road, SBIP,
Hsin-Chu, Taiwan
Tel : 886-3-5642000
Fax : 886-3-5642050
Taipei Branch :
2F, No. 11, Lane 218, Sec 2 Jhongsing Rd.,
Sindian City, Taipei County 23146, Taiwan
Tel : 886-2-2910-3838
Fax : 886-2-2917-3838
Copyright  ANPEC Electronics Corp.
Rev. A.5 - Jul., 2013
18
www.anpec.com.tw
Similar pages