BCR8KM-12LA Triac Medium Power Use REJ03G0318-0100 Rev.1.00 Aug.20.2004 Features • • • • • Insulated Type • Planar Passivation Type • UL Recognized : Yellow Card No. E223904 File No. E80271 IT (RMS) : 8 A VDRM : 600 V IFGTI , IRGTI, IRGTⅢ : 30 mA (20 mA)Note5 Viso : 2000 V Outline TO-220FN 2 1. T1 Terminal 2. T2 Terminal 3. Gate Terminal 3 1 1 2 3 Applications Switching mode power supply, washing machine, motor control, heater control, and other general purpose control applications Maximum Ratings Parameter Repetitive peak off-state voltageNote1 Non-repetitive peak off-state voltageNote1 Rev.1.00, Aug.20.2004, page 1 of 7 Symbol Voltage class 12 Unit VDRM VDSM 600 720 V V BCR8KM-12LA Parameter RMS on-state current Symbol IT (RMS) Ratings 8 Unit A Surge on-state current ITSM 80 A I2 t 26 A2s PGM PG (AV) VGM IGM Tj Tstg — Viso 5 0.5 10 2 – 40 to +125 – 40 to +125 2.0 2000 W W V A °C °C g V Symbol Min. Typ. Max. Unit IDRM VTM — — — — 2.0 1.6 mA V Tj = 125°C, VDRM applied Tc = 25°C, ITM = 12 A, Instantaneous measurement VFGTΙ VRGTΙ VRGTΙΙΙ IFGTΙ IRGTΙ IRGTΙΙΙ VGD Rth (j-c) (dv/dt)c — — — — — — 0.2 — 10 — — — — — — — — — 1.5 1.5 1.5 30Note5 30Note5 30Note5 — 3.6 — V V V mA mA mA V °C/W V/µs Tj = 25°C, VD = 6 V, RL = 6 Ω, RG = 330 Ω I2t for fusing Peak gate power dissipation Average gate power dissipation Peak gate voltage Peak gate current Junction temperature Storage temperature Mass Isolation voltage Conditions Commercial frequency, sine full wave 360° conduction, Tc = 89°C 60Hz sinewave 1 full cycle, peak value, non-repetitive Value corresponding to 1 cycle of half wave 60Hz, surge on-state current Typical value Ta = 25°C, AC 1 minute, T1·T2·G terminal to case Notes: 1. Gate open. Electrical Characteristics Parameter Repetitive peak off-state current On-state voltage Gate trigger voltageNote2 Gate trigger currentNote2 Ι ΙΙ ΙΙΙ Ι ΙΙ ΙΙΙ Test conditions Tj = 25°C, VD = 6 V, RL = 6 Ω, RG = 330 Ω Gate non-trigger voltage Tj = 125°C, VD = 1/2 VDRM Thermal resistance Junction to caseNote3 Critical-rate of rise of off-state Tj = 125°C commutating voltageNote4 Notes: 2. Measurement using the gate trigger characteristics measurement circuit. 3. The contact thermal resistance Rth (c-f) in case of greasing is 0.5°C/W. 4. Test conditions of the critical-rate of rise of off-state commutating voltage is shown in the table below. 5. High sensitivity (IGT ≤ 20 mA) is also available. (IGT item: 1) Test conditions 1. Junction temperature Tj = 125°C 2. Rate of decay of on-state commutating current (di/dt)c = – 4 A/ms 3. Peak off-state voltage VD = 400 V Rev.1.00, Aug.20.2004, page 2 of 7 Commutating voltage and current waveforms (inductive load) Supply Voltage Time Main Current (di/dt)c Time Main Voltage (dv/dt)c Time VD BCR8KM-12LA Performance Curves 102 7 5 3 2 Tj = 125°C Tj = 25°C 100 7 5 3 2 –1 Gate Trigger Voltage (Tj = t°C) × 100 (%) Gate Trigger Voltage (Tj = 25°C) 50 40 30 20 10 2 3 5 7 10 1 2 3 5 7 10 Gate Characteristics (I, II and III) Gate Trigger Current vs. Junction Temperature PG(AV) = 0.5W PGM = 5W IGM = 2A VGT = 1.5V IFGT I IRGT I, IRGT III VGD = 0.2V 7 5 101 2 3 5 7102 2 3 5 7103 2 3 5 7104 103 7 5 60 Conduction Time (Cycles at 60Hz) 100 7 5 3 2 –1 80 70 On-State Voltage (V) Gate Trigger Current (Tj = t°C) × 100 (%) Gate Trigger Current (Tj = 25°C) Gate Voltage (V) 101 7 5 3 2 90 0 0 10 0.6 1.0 1.4 1.8 2.2 2.6 3.0 3.4 3.8 3 2 VGM = 10V 10 Surge On-State Current (A) 100 101 7 5 3 2 10 Rated Surge On-State Current 103 7 5 3 2 102 7 5 2 Typical Example IRGT III IRGT I, IFGT I 3 2 101 –60 –40–20 0 20 40 60 80 100 120 140 Gate Current (mA) Junction Temperature (°C) Gate Trigger Voltage vs. Junction Temperature Maximum Transient Thermal Impedance Characteristics (Junction to case) Typical Example 3 2 102 7 5 3 2 1 10 –60 –40–20 0 20 40 60 80 100 120 140 Junction Temperature (°C) Rev.1.00, Aug.20.2004, page 3 of 7 Transient Thermal Impedance (°C/W) On-State Current (A) Maximum On-State Characteristics 102 2 3 5 7 103 2 3 5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 10–1 2 3 5 7 100 2 3 5 7 101 2 3 5 7 102 Conduction Time (Cycles at 60Hz) BCR8KM-12LA Maximum On-State Power Dissipation 3 10 7 5 3 2 2 10 7 5 3 2 1 10 7 5 3 2 0 10 7 5 3 2 –1 10 1 No Fins 16 On-State Power Dissipation (W) Transient Thermal Impedance (°C/W) Maximum Transient Thermal Impedance Characteristics (Junction to ambient) Resistive, 10 inductive loads 8 6 4 2 2 4 6 8 10 12 14 16 Conduction Time (Cycles at 60Hz) RMS On-State Current (A) Allowable Case Temperature vs. RMS On-State Current Allowable Ambient Temperature vs. RMS On-State Current 120 100 80 60 40 360° Conduction Resistive, inductive loads 20 0 0 2 4 6 8 Ambient Temperature (°C) 160 Curves apply regardless 140 of conduction angle All fins are black painted 140 aluminum and greased 120 × 120 × t2.3 120 100 × 100 × t2.3 100 60 × 60 × t2.3 80 60 Curves apply regardless of conduction angle Resistive, inductive loads Natural convection 40 20 0 0 10 12 14 16 2 4 6 8 10 12 14 16 RMS On-State Current (A) RMS On-State Current (A) Allowable Ambient Temperature vs. RMS On-State Current Repetitive Peak Off-State Current vs. Junction Temperature 160 Natural convection No Fins Curves apply regardless of conduction angle Resistive, inductive loads 140 120 100 80 60 40 20 0 0 0.5 1.0 1.5 2.0 2.5 RMS On-State Current (A) Rev.1.00, Aug.20.2004, page 4 of 7 3.0 Repetitive Peak Off-State Current (Tj = t°C) × 100 (%) Repetitive Peak Off-State Current (Tj = 25°C) Case Temperature (°C) 12 360° Conduction 0 0 10 2 3 5 7102 2 3 5 7103 2 3 5 7104 2 3 5 7105 160 Ambient Temperature (°C) 14 105 7 5 3 2 Typical Example 104 7 5 3 2 103 7 5 3 2 102 –60 –40–20 0 20 40 60 80 100 120 140 Junction Temperature (°C) BCR8KM-12LA Latching Current vs. Junction Temperature 3 10 7 5 Latching Current (mA) Typical Example 3 2 102 7 5 3 2 101 –60 –40–20 0 20 40 60 80 100 120 140 100 80 60 40 20 0 –60 –40–20 0 20 40 60 80 100 120 140 120 160 160 Typical Example Tj = 125°C 140 120 100 80 60 III Quadrant 40 20 I Quadrant 0 1 2 3 4 10 2 3 5 710 2 3 5 710 2 3 5 710 Junction Temperature (°C) Rate of Rise of Off-State Voltage (V/µs) Commutation Characteristics Gate Trigger Current vs. Gate Current Pulse Width Time Main Voltage (dv/dt)c VD Main Current (di/dt)c IT τ Time 1 100 7 0 10 Breakover Voltage (dv/dt = xV/µs) × 100 (%) Breakover Voltage (dv/dt = 1V/µs) 120 3 2 101 7 5 3 T2+, G+ 2 T –, G– Typical Example 2 100 –40 0 40 80 Breakover Voltage vs. Rate of Rise of Off-State Voltage 140 10 7 5 T2+, G– Typical Example 102 7 5 3 2 Breakover Voltage vs. Junction Temperature Typical Example 3 2 Distribution Junction Temperature (°C) 160 7 5 103 7 5 3 2 Junction Temperature (°C) Typical Example Tj = 125°C IT = 4A τ = 500µs VD = 200V f = 3Hz Minimum Characteristics Value I Quadrant III Quadrant 2 3 5 7 101 2 3 5 7 102 Rate of Decay of On-State Commutating Current (A/ms) Rev.1.00, Aug.20.2004, page 5 of 7 Gate Trigger Current (tw) × 100 (%) Gate Trigger Current (DC) Critical Rate of Rise of Off-State Commutating Voltage (V/µs) Breakover Voltage (Tj = t°C) × 100 (%) Breakover Voltage (Tj = 25°C) Holding Current (Tj = t°C) × 100 (%) Holding Current (Tj = 25°C) Holding Current vs. Junction Temperature 103 7 5 Typical Example IFGT I IRGT I 3 2 IRGT III 102 7 5 3 2 1 10 0 10 2 3 5 7 101 2 3 5 7 102 Gate Current Pulse Width (µs) BCR8KM-12LA Gate Trigger Characteristics Test Circuits 6Ω 6Ω A 6V V Test Procedure I 6Ω A 6V V A 6V 330Ω 330Ω Test Procedure III Rev.1.00, Aug.20.2004, page 6 of 7 V 330Ω Test Procedure II BCR8KM-12LA Package Dimensions TO-220FN EIAJ Package Code JEDEC Code Mass (g) (reference value) Lead Material 2.0 Cu alloy 2.8 ± 0.2 6.5 ± 0.3 3 ± 0.3 φ 3.2 ± 0.2 3.6 ± 0.3 14 ± 0.5 15 ± 0.3 10 ± 0.3 1.1 ± 0.2 1.1 ± 0.2 0.75 ± 0.15 0.75 ± 0.15 2.54 ± 0.25 4.5 ± 0.2 2.54 ± 0.25 2.6 ± 0.2 Symbol Dimension in Millimeters Min Typ Max A A1 A2 b D E e x y y1 ZD ZE Note 1) The dimensional figures indicate representative values unless otherwise the tolerance is specified. Order Code Lead form Standard packing Quantity Standard order code Straight type Plastic Magazine (Tube) 50 Type name Lead form Plastic Magazine (Tube) 50 Type name – Lead forming code Note : Please confirm the specification about the shipping in detail. Rev.1.00, Aug.20.2004, page 7 of 7 Standard order code example BCR8KM-12LA BCR8KM-12LA-A8 Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap. Notes regarding these materials 1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party. 2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials. 3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or typographical errors. Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor home page (http://www.renesas.com). 4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes no responsibility for any damage, liability or other loss resulting from the information contained herein. 5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. 6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials. 7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. 8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein. http://www.renesas.com RENESAS SALES OFFICES Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500 Fax: <1> (408) 382-7501 Renesas Technology Europe Limited. Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, United Kingdom Tel: <44> (1628) 585 100, Fax: <44> (1628) 585 900 Renesas Technology Europe GmbH Dornacher Str. 3, D-85622 Feldkirchen, Germany Tel: <49> (89) 380 70 0, Fax: <49> (89) 929 30 11 Renesas Technology Hong Kong Ltd. 7/F., North Tower, World Finance Centre, Harbour City, Canton Road, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2375-6836 Renesas Technology Taiwan Co., Ltd. FL 10, #99, Fu-Hsing N. Rd., Taipei, Taiwan Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999 Renesas Technology (Shanghai) Co., Ltd. 26/F., Ruijin Building, No.205 Maoming Road (S), Shanghai 200020, China Tel: <86> (21) 6472-1001, Fax: <86> (21) 6415-2952 Renesas Technology Singapore Pte. Ltd. 1, Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: <65> 6213-0200, Fax: <65> 6278-8001 © 2004. Renesas Technology Corp., All rights reserved. Printed in Japan. Colophon .1.0