AD ADV7391BCPZ Low power, chip scale 10-bit sd/hd video encoder Datasheet

Low Power, Chip Scale
10-Bit SD/HD Video Encoder
ADV7390/ADV7391/ADV7392/ADV7393
FEATURES
NTSC and PAL square pixel operation (24.54 MHz/29.5 MHz)
Macrovision® Rev 7.1.L1 (SD) and Rev 1.2 (ED) compliant
Programmable features
Luma and chroma filter responses
Vertical blanking interval (VBI)
Subcarrier frequency (FSC) and phase
Luma delay
Copy generation management system (CGMS)
Closed captioning and wide screen signaling (WSS)
Integrated subcarrier locking to external video source
Complete on-chip video timing generator
On-chip test pattern generation
Serial MPU interface with dual I2C® and SPI® compatibility
2.7 V or 3.3 V analog operation
1.8 V digital operation
3.3 V I/O operation
Temperature range: −40°C to +85°C
3 high quality, 10-bit video DACs
16× (216 MHz) DAC oversampling for SD
8× (216 MHz) DAC oversampling for ED
4× (297 MHz) DAC oversampling for HD
37 mA maximum DAC output current
Multiformat video input support
4:2:2 YCrCb (SD, ED, and HD)
4:4:4 RGB (SD)
Multiformat video output support
Composite (CVBS) and S-Video (Y/C)
Component YPrPb (SD, ED, and HD)
Component RGB (SD, ED, and HD)
Lead frame chip scale package (LFCSP) options
32-lead, 5 mm × 5 mm LFCSP
40-lead, 6 mm × 6 mm LFCSP
Advanced power management
Patented content-dependent low power DAC operation
Automatic cable detection and DAC power-down
Individual DAC on/off control
Sleep mode with minimal power consumption
74.25 MHz 8-/10-/16-bit high definition input support
Compliant with SMPTE 274M (1080i), 296M (720p),
and 240M (1035i)
EIA/CEA-861B compliance support
NTSC M, PAL B/D/G/H/I/M/N, PAL 60 support
APPLICATIONS
Mobile handsets
Digital still cameras
Portable media and DVD players
Portable game consoles
Digital camcorders
Set-top box (STB)
Automotive infotainment (ADV7393 only)
FUNCTIONAL BLOCK DIAGRAM
VBI DATA SERVICE
INSERTION
SCL/ SDA/ ALSB/
MOSI SCLK SPI_SS
MPU PORT
VDD_IO
4:2:2 TO 4:4:4
P15 TO P0/
P7 TO P0
INPUT
DEINTERLEAVE
RGB/YCrCb
TO
YUV
MATRIX
SFL/
MISO
AGND
ADV739x
SUBCARRIER FREQUENCY
LOCK (SFL)
ADD
SYNC
PROGRAMMABLE
LUMINANCE
FILTER
YUV
TO
YCrCb/
RGB
16×
FILTER
ADD
BURST
PROGRAMMABLE
CHROMINANCE
FILTER
SIN/COS DDS
BLOCK
16×
FILTER
ASYNC
BYPASS
YCrCb
HDTV
TEST
PATTERN
GENERATOR
POWER
MANAGEMENT
CONTROL
RESET
PROGRAMMABLE
ED/HD FILTERS
YCbCr
TO
RGB MATRIX
HSYNC
VSYNC
16x/4x OVERSAMPLING PLL
CLKIN
10-BIT
DAC 1
DAC 1
10-BIT
DAC 2
DAC 2
10-BIT
DAC 3
DAC 3
4×
FILTER
SHARPNESS AND
ADAPTIVE FILTER
CONTROL
VIDEO TIMING GENERATOR
VAA
PVDD
PGND EXT_LF
REFERENCE
AND CABLE
DETECT
COMP
RSET
06234-001
GND_IO
VDD (2)
MULTIPLEXER
DGND (2)
Figure 1.
Protected by U.S. Patent Numbers 5,343,196 and 5,442,355 and other intellectual property rights.
Protected by U.S. Patent Numbers 4,631,603, 4,577,216, 4,819,098, and other intellectual property rights.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2006 Analog Devices, Inc. All rights reserved.
ADV7390/ADV7391/ADV7392/ADV7393
TABLE OF CONTENTS
Features .............................................................................................. 1
Applications....................................................................................... 1
SD Subcarrier Frequency Lock, Subcarrier Reset, and Timing
Reset ............................................................................................. 46
Functional Block Diagram .............................................................. 1
SD VCR FF/RW Sync ................................................................ 47
Revision History ............................................................................... 3
Vertical Blanking Interval ......................................................... 47
Detailed Features .............................................................................. 4
SD Subcarrier Frequency Registers.......................................... 47
General Description ......................................................................... 4
SD NonInterlaced Mode............................................................ 48
Specifications..................................................................................... 5
SD Square Pixel Mode ............................................................... 48
Power Supply Specifications........................................................ 5
Filters............................................................................................ 49
Input Clock Specifications .......................................................... 5
ED/HD Test Pattern Color Controls ....................................... 50
Analog Output Specifications..................................................... 5
Color Space Conversion Matrix ............................................... 50
Digital Input/Output Specifications........................................... 6
SD Luma and Color Control..................................................... 51
MPU Port Timing Specifications ............................................... 6
SD Hue Adjust Control.............................................................. 52
Digital Timing Specifications ..................................................... 7
SD Brightness Detect ................................................................. 52
Video Performance Specifications ............................................. 8
SD Brightness Control............................................................... 52
Power Specifications .................................................................... 8
SD Input Standard Auto Detection.......................................... 52
Timing Diagrams.............................................................................. 9
Double Buffering ........................................................................ 53
Absolute Maximum Ratings.......................................................... 15
Programmable DAC Gain Control .......................................... 53
Thermal Resistance .................................................................... 15
Gamma Correction .................................................................... 53
ESD Caution................................................................................ 15
ED/HD Sharpness Filter and Adaptive Filter Controls......... 55
Pin Configurations and Function Descriptions ......................... 16
ED/HD Sharpness Filter and Adaptive Filter Application
Examples...................................................................................... 56
Typical Performance Characteristics ........................................... 18
MPU Port Description................................................................... 23
I2C Operation.............................................................................. 23
SD Digital Noise Reduction...................................................... 57
SD Active Video Edge Control ................................................. 59
SPI Operation.............................................................................. 24
External Horizontal and Vertical
Synchronization Control ........................................................... 60
Register Map.................................................................................... 25
Low Power Mode........................................................................ 61
Register Programming............................................................... 25
Cable Detection .......................................................................... 61
Subaddress Register (SR7 to SR0) ............................................ 25
DAC Auto Power-Down............................................................ 61
ADV7390/ADV7391 Input Configuration ................................. 41
Pixel and Control Port Readback............................................. 61
Standard Definition.................................................................... 41
Reset Mechanisms ...................................................................... 61
Enhanced Definition/High Definition .................................... 41
Printed Circuit Board Layout and Design .................................. 62
Enhanced Definition (At 54 MHz) .......................................... 41
DAC Configurations.................................................................. 62
ADV7392/ADV7393 Input Configuration ................................. 42
Video Output Buffer and Optional Output Filter.................. 62
Standard Definition.................................................................... 42
Printed Circuit Board (PCB) Layout ....................................... 63
Enhanced Definition/High Definition .................................... 43
Typical Application Circuit....................................................... 65
Enhanced Definition (At 54 MHz) .......................................... 43
Appendix 1–Copy Generation Management System ................ 66
Output Configuration .................................................................... 44
SD CGMS .................................................................................... 66
Features ............................................................................................ 45
ED CGMS.................................................................................... 66
Output Oversampling ................................................................ 45
HD CGMS................................................................................... 66
ED/HD Nonstandard Timing Mode........................................ 45
CGMS CRC Functionality ........................................................ 66
ED/HD Timing Reset ................................................................ 46
Appendix 2–SD Wide Screen Signaling ...................................... 69
Rev. 0 | Page 2 of 96
ADV7390/ADV7391/ADV7392/ADV7393
Appendix 3–SD Closed Captioning..............................................70
SD/ED/HD RGB Output Levels................................................80
Appendix 4–Internal Test Pattern Generation ............................71
SD Output Plots ..........................................................................81
SD Test Patterns...........................................................................71
Appendix 8–Video Standards........................................................82
ED/HD Test Patterns ..................................................................71
Appendix 9–Configuration Scripts...............................................84
Appendix 5–SD Timing..................................................................72
Standard Definition ....................................................................84
Appendix 6–HD Timing ................................................................77
Enhanced Definition ..................................................................90
Appendix 7–Video Output Levels.................................................78
High Definition ...........................................................................92
SD YPrPb Output Levels—SMPTE/EBU N10 ........................78
Outline Dimensions........................................................................95
ED/HD YPrPb Output Levels ...................................................79
Ordering Guide ...........................................................................96
REVISION HISTORY
10/06—Revision 0: Initial Version
Rev. 0 | Page 3 of 96
ADV7390/ADV7391/ADV7392/ADV7393
DETAILED FEATURES
High definition (HD) programmable features
(720p/1080i/1035i)
4× oversampling (297 MHz)
Internal test pattern generator
Color and black bar, hatch, flat field/frame
Fully programmable YCrCb to RGB matrix
Gamma correction
Programmable adaptive filter control
Programmable sharpness filter control
CGMS (720p/1080i) and CGMS Type B (720p/1080i)
Dual data rate (DDR) input support
EIA/CEA-861B compliance support
Enhanced definition (ED) programmable features
(525p/625p)
8× oversampling (216 MHz output)
Internal test pattern generator
Color and black bar, hatch, flat field/frame
Individual Y and PrPb output delay
Gamma correction
Programmable adaptive filter control
Fully programmable YCrCb to RGB matrix
Undershoot limiter
Macrovision Rev 1.2 (525p/625p)
CGMS (525p/625p) and CGMS Type B (525p)
Dual data rate (DDR) input support
EIA/CEA-861B compliance support
Standard definition (SD) programmable features
16× oversampling (216 MHz)
Internal test pattern generator
Color and black bar
Controlled edge rates for start and end of active video
Individual Y and PrPb output delay
Undershoot limiter
Gamma correction
Digital noise reduction (DNR)
Multiple chroma and luma filters
Luma-SSAF™ filter with programmable gain/attenuation
PrPb SSAF™
Separate pedestal control on component and
composite/S-Video output
VCR FF/RW sync mode
Macrovision Rev 7.1.L1
Copy generation management system (CGMS)
Wide screen signaling (WSS)
Closed captioning
EIA/CEA-861B compliance support
GENERAL DESCRIPTION
The ADV7390/ADV7391/ADV7392/ADV7393 are a family of
high speed, digital-to-analog video encoders on single
monolithic chips. Three 2.7 V/3.3 V 10-bit video DACs provide
support for composite (CVBS), S-Video (YC), or component
(YPrPb/RGB) analog outputs in either standard-definition (SD)
or high-definition (HD) video formats.
Optimized for low power operation, occupying a minimal
footprint and requiring few external components, these
encoders are ideally suited to portable and power sensitive
applications requiring TV-Out functionality. Cable detection
and DAC auto power-down features ensure that power
consumption is kept to a minimum.
The ADV7390/ADV7391 have an 8-bit video input port that
supports SD video formats over a SDR interface and HD video
formats over a DDR interface.
The ADV7392/ADV7393 have a 16-bit video input port that
can be configured in a variety of ways. SD RGB input is
supported.
All members of the family support embedded EAV/SAV timing
codes, external video synchronization signals and the I2C and
SPI communication protocols.
Table 1 lists the video standards directly supported by the
ADV739x family.
Table 1. Standards Directly Supported by the ADV739x 1
Resolution
720 × 240
720 × 288
720 × 480
I/P 2
P
P
I
Frame
Rate (Hz)
59.94
50
29.97
Clock Input
(MHz)
27
27
27
720 × 576
I
25
27
720 × 480
I
29.97
24.54
720 × 576
I
25
29.5
720 × 483
720 × 483
720 × 483
720 × 576
720 × 483
720 × 576
1920 × 1035
1920 × 1035
1280 × 720
P
P
P
P
P
P
I
I
P
27
27
27
27
27
27
74.25
74.1758
74.25
1280 × 720
P
74.1758
SMPTE 296M
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
I
I
P
P
P
59.94
59.94
59.94
50
59.94
50
30
29.97
60, 50, 30,
25, 24
23.97,
59.94, 29.97
30, 25
29.97
30, 25, 24
23.98, 29.97
24
ITU-R
BT.601/656
ITU-R
BT.601/656
NTSC Square
Pixel
PAL Square
Pixel
SMPTE 293M
BTA T-1004
ITU-R BT.1358
ITU-R BT.1358
ITU-R BT.1362
ITU-R BT.1362
SMPTE 240M
SMPTE 240M
SMPTE 296M
74.25
74.1758
74.25
74.1758
74.25
SMPTE 274M
SMPTE 274M
SMPTE 274M
SMPTE 274M
ITU-R BT.7095
1
2
Standard
Other standards are supported in the ED/HD nonstandard timing mode.
I = interlaced, P = progressive.
Rev. 0 | Page 4 of 96
ADV7390/ADV7391/ADV7392/ADV7393
SPECIFICATIONS
POWER SUPPLY SPECIFICATIONS
All specifications TMIN to TMAX (−40°C to +85°C), unless otherwise noted.
Table 2.
Parameter
SUPPLY VOLTAGES
VDD
VDD_IO
PVDD
VAA
POWER SUPPLY REJECTION RATIO
Conditions
Min
Typ
Max
Unit
1.71
2.97
1.71
2.6
1.8
3.3
1.8
3.3
0.002
1.89
3.63
1.89
3.465
V
V
V
V
%/%
INPUT CLOCK SPECIFICATIONS
VDD = 1.71 V to 1.89 V, PVDD = 1.71 V to 1.89 V, VAA = 2.6 V to 3.465 V, VDD_IO = 2.97 V to 3.63 V.
All specifications TMIN to TMAX (−40°C to +85°C), unless otherwise noted.
Table 3.
Parameter
fCLKIN
Conditions 1
SD/ED
ED (at 54 MHz)
HD
CLKIN High Time, t9
CLKIN Low Time, t10
CLKIN Peak-to-Peak Jitter Tolerance
1
Min
Typ
27
54
74.25
Max
40
40
2
Unit
MHz
MHz
MHz
% of one clock cycle
% of one clock cycle
±ns
SD = standard definition, ED = enhanced definition (525p/625p), HD = high definition.
ANALOG OUTPUT SPECIFICATIONS
VDD = 1.71 V to 1.89 V, PVDD = 1.71 V to 1.89 V, VAA = 2.6 V to 3.465 V, VDD_IO = 2.97 V to 3.63 V.
All specifications TMIN to TMAX (−40°C to +85°C), unless otherwise noted.
Table 4.
Parameter
Full-Drive Output Current
Low Drive Output Current
DAC-to-DAC Matching
Output Compliance, VOC
Output Capacitance, COUT
Analog Output Delay 1
DAC Analog Output Skew
1
Conditions
RSET = 510 Ω, RL = 37.5 Ω
RSET = 4.12 kΩ, RL = 300 Ω
DAC 1, DAC 2, DAC 3
Min
33
Typ
34.6
4.3
2.0
0
DAC 1, DAC 2, DAC 3
1.4
10
6
1
Output delay measured from the 50% point of the rising edge of the input clock to the 50% point of the DAC output full-scale transition.
Rev. 0 | Page 5 of 96
Max
37
Unit
mA
mA
%
V
pF
ns
ns
ADV7390/ADV7391/ADV7392/ADV7393
DIGITAL INPUT/OUTPUT SPECIFICATIONS
VDD = 1.71 V to 1.89 V, PVDD = 1.71 V to 1.89 V, VAA = 2.6 V to 3.465 V, VDD_IO = 2.97 V to 3.63 V.
All specifications TMIN to TMAX (−40°C to +85°C), unless otherwise noted.
Table 5.
Parameter
Input High Voltage, VIH
Input Low Voltage, VIL
Input Leakage Current, IIN
Input Capacitance, CIN
Output High Voltage, VOH
Output Low Voltage, VOL
Three-State Leakage Current
Three-State Output Capacitance
Conditions
Min
2.0
Typ
Max
Unit
V
V
μA
pF
V
V
μA
pF
0.8
±10
VIN = VDD_IO
4
ISOURCE = 400 μA
ISINK = 3.2 mA
VIN = 0.4 V, 2.4 V
2.4
0.4
±1
4
MPU PORT TIMING SPECIFICATIONS
VDD = 1.71 V to 1.89 V, PVDD = 1.71 V to 1.89 V, VAA = 2.6 V to 3.465 V, VDD_IO = 2.97 V to 3.63 V.
All specifications TMIN to TMAX (−40°C to +85°C), unless otherwise noted.
Table 6.
Parameter
MPU PORT, I2C MODE 1
SCL Frequency
SCL High Pulse Width, t1
SCL Low Pulse Width, t2
Hold Time (Start Condition), t3
Setup Time (Start Condition), t4
Data Setup Time, t5
SDA, SCL Rise Time, t6
SDA, SCL Fall Time, t7
Setup Time (Stop Condition), t8
MPU PORT, SPI MODE1
SCLK Frequency
SPI_SS to SCLK Setup Time, t1
SCLK High Pulse Width, t2
SCLK Low Pulse Width, t3
Data Access Time after SCLK Falling Edge, t4
Data Setup Time prior to SCLK Rising Edge, t5
Data Hold Time after SCLK Rising Edge, t6
SPI_SS to SCLK Hold Time, t7
SPI_SS to MISO High Impedance, t8
1
Conditions
See Figure 15
Min
0
0.6
1.3
0.6
0.6
100
Typ
Max
Unit
400
kHz
μs
μs
μs
μs
ns
ns
ns
μs
300
300
0.6
See Figure 16
0
20
50
50
10
35
20
0
0
40
Guaranteed by characterization.
Rev. 0 | Page 6 of 96
MHz
ns
ns
ns
ns
ns
ns
ns
ns
ADV7390/ADV7391/ADV7392/ADV7393
DIGITAL TIMING SPECIFICATIONS
VDD = 1.71 V to 1.89 V, PVDD = 1.71 V to 1.89 V, VAA = 2.6 V to 3.465 V, VDD_IO = 2.97 V to 3.63 V.
All specifications TMIN to TMAX (−40°C to +85°C), unless otherwise noted.
Table 7.
Parameter
VIDEO DATA AND VIDEO CONTROL PORT 2, 3
Data Input Setup Time, t11 4
Data Input Hold Time, t124
Control Input Setup Time, t114
Control Input Hold Time, t124
Control Output Access Time, t134
Control Output Hold Time, t144
PIPELINE DELAY 5
SD1
CVBS/YC Outputs (2×)
CVBS/YC Outputs (8×)
CVBS/YC Outputs (16×)
Component Outputs (2×)
Component Outputs (8×)
Component Outputs (16×)
ED1
Component Outputs (1×)
Component Outputs (4×)
Component Outputs (8×)
HD1
Component Outputs (1×)
Component Outputs (2×)
Component Outputs (4×)
RESET CONTROL
RESET Low Time
Conditions 1
Min
SD
ED/HD-SDR
ED/HD-DDR
ED (at 54 MHz)
SD
ED/HD-SDR
ED/HD-DDR
ED (at 54 MHz)
SD
ED/HD-SDR or ED/HD-DDR
ED (at 54 MHz)
SD
ED/HD-SDR or ED/HD-DDR
ED (at 54 MHz)
SD
ED/HD-SDR, ED/HD-DDR, or ED (at 54 MHz)
SD
ED/HD-SDR, ED/HD-DDR, or ED (at 54 MHz)
2.1
2.3
2.3
1.7
1.0
1.1
1.1
1.0
2.1
2.3
1.7
1.0
1.1
1.0
Typ
Max
12
10
4.0
3.5
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
SD oversampling disabled
SD oversampling disabled
SD oversampling enabled
SD oversampling disabled
SD oversampling disabled
SD oversampling enabled
68
79
67
78
69
84
clock cycles
clock cycles
clock cycles
clock cycles
clock cycles
clock cycles
ED oversampling disabled
ED oversampling disabled
ED oversampling enabled
41
49
46
clock cycles
clock cycles
clock cycles
HD oversampling disabled
HD oversampling disabled
HD oversampling enabled
40
42
44
clock cycles
clock cycles
clock cycles
100
1
SD = standard definition, ED = enhanced definition (525p/625p), HD = high definition, SDR = single data rate, DDR = dual data rate.
Video Data: P[15:0] for ADV7392/ADV7393 or P[7:0] for ADV7390/ADV7391.
3
Video Control: HSYNC and VSYNC.
4
Guaranteed by characterization.
5
Guaranteed by design.
2
Rev. 0 | Page 7 of 96
ns
ADV7390/ADV7391/ADV7392/ADV7393
VIDEO PERFORMANCE SPECIFICATIONS
Table 8.
Parameter
STATIC PERFORMANCE
Resolution
Integral Nonlinearity (INL) 1
Differential Nonlinearity (DNL)1, 2
STANDARD DEFINTION (SD) MODE
Luminance Nonlinearity
Differential Gain
Differential Phase
Signal-to-Noise Ratio (SNR) 3
Conditions
Min
Typ
Max
Unit
RSET = 510 Ω, RL = 37.5 Ω
RSET = 510 Ω, RL = 37.5 Ω
10
0.5
0.5
Bits
LSBs
LSBs
NTSC
NTSC
Luma ramp
Flat field full bandwidth
0.5
0.5
0.6
58
75
±%
%
Degrees
dB
dB
12.5
5.8
MHz
MHz
30.0
13.75
MHz
MHz
ENHANCED DEFINITION (ED) MODE
Luma Bandwidth
Chroma Bandwidth
HIGH DEFINITION (HD) MODE
Luma Bandwidth
Chroma Bandwidth
1
Measured on DAC 1, DAC 2, and DAC 3.
Differential nonlinearity (DNL) measures the deviation of the actual DAC output voltage step from the ideal. For +ve DNL, the actual step value lies above the ideal
step value. For −ve DNL, the actual step value lies below the ideal step value.
3
Measured on the ADV7392/ADV7393 operating in 10-bit input mode.
2
POWER SPECIFICATIONS
Table 9.
Parameter
NORMAL POWER MODE 1, 2
IDD 3
IDD_IO
IAA 5
Conditions
Min
SD (16× oversampling enabled), CVBS
SD (16× oversampling enabled), YPrPb
ED (8× oversampling enabled) 4
HD (4× oversampling enabled)4
1 DAC enabled
All DACs enabled
IPLL
SLEEP MODE
IDD
IAA
IDD_IO
IPLL
1
RSET = 510 Ω (all DACs operating in full-drive mode).
75% color bar test pattern applied to pixel data pins.
IDD is the continuous current required to drive the digital core.
4
Applicable to both single data rate (SDR) and dual data rate (DDR) input modes.
5
IAA is the total current required to supply all DACs.
2
3
Rev. 0 | Page 8 of 96
Typ
Max
Unit
33
68
59
81
1
50
122
4
mA
mA
mA
mA
mA
mA
mA
mA
5
0.3
0.2
0.1
μA
μA
μA
μA
ADV7390/ADV7391/ADV7392/ADV7393
TIMING DIAGRAMS
The following abbreviations are used in Figure 2 to Figure 9.
t9 = Clock high time
t10 = Clock low time
t11 = Data setup time
t12 = Data hold time
t13 = Control output access time
t14 = Control output hold time
CLKIN
t9
CONTROL
INPUTS
t12
t10
HSYNC
IN SLAVE MODE
VSYNC
PIXEL PORT
Y0
Cb0
Y1
Cr0
t11
Y2
Cb2
Cr2
t13
CONTROL
OUTPUTS
06234-002
IN MASTER/SLAVE MODE
t14
Figure 2. SD Input, 8-/10-Bit 4:2:2 YCrCb (Input Mode 000)
CLKIN
t9
CONTROL
INPUTS
t12
t10
HSYNC
IN SLAVE MODE
VSYNC
PIXEL PORT
Y0
Y1
Y2
Y3
PIXEL PORT
Cb0
Cr0
Cb2
Cr2
t11
t13
CONTROL
OUTPUTS
IN MASTER/SLAVE MODE
t14
Figure 3. SD Input, 16-Bit 4:2:2 YCrCb (Input Mode 000)
Rev. 0 | Page 9 of 96
06234-003
•
•
•
•
•
•
In addition, refer to Table 30 for the ADV7390/ADV7391 input
configuration and Table 31 for the ADV7392/ADV7393 input
configuration.
ADV7390/ADV7391/ADV7392/ADV7393
CLKIN
t9
HSYNC
IN SLAVE MODE
VSYNC
PIXEL PORT
Y0
Y1
Y2
Y3
PIXEL PORT
Cb0
Cr0
Cb2
Cr2
t11
t13
CONTROL
OUTPUTS
06234-003
IN MASTER/SLAVE MODE
t14
Figure 4. SD Input, 16-Bit 4:4:4 RGB (Input Mode 000)
CLKIN
t9
CONTROL
INPUTS
t12
t10
HSYNC
VSYNC
PIXEL PORT
G0
G1
G2
PIXEL PORT
B0
B1
B2
R1
R2
t11
PIXEL PORT
R0
CONTROL
OUTPUTS
06234-004
t14
t13
Figure 5. ED/HD-SDR Input, 16-Bit 4:2:2 YCrCb (Input Mode 001)
CLKIN*
t9
CONTROL
INPUTS
t10
HSYNC
VSYNC
PIXEL PORT
Cb0
t11
Y0
Cr0
Y1
t12
Cb2
Y2
Cr2
t12
t11
t13
CONTROL
OUTPUTS
t14
*LUMA/CHROMA CLOCK RELATIONSHIP CAN BE INVERTED USING SUBADDRESS 0x01, BITS 1 AND 2.
Figure 6. ED/HD-DDR Input, 8-/10-Bit 4:2:2 YCrCb (HSYNC/VSYNC), Input Mode 010
Rev. 0 | Page 10 of 96
06234-006
CONTROL
INPUTS
t12
t10
ADV7390/ADV7391/ADV7392/ADV7393
CLKIN*
t9
PIXEL PORT
3FF
t11
t10
00
00
XY
t12
Cb0
Y0
Cr0
Y1
t12
t11
t13
t14
*LUMA/CHROMA CLOCK RELATIONSHIP CAN BE INVERTED USING SUBADDRESS 0x01, BITS 1 AND 2.
06234-007
CONTROL
OUTPUTS
Figure 7. ED/HD-DDR Input, 8-/10-Bit 4:2:2 YCrCb (EAV/SAV), Input Mode 010
CLKIN
t9
CONTROL
INPUTS
t10
HSYNC
VSYNC
Cb0
PIXEL PORT
Y0
Cr0
Y1
t12
t11
Cb2
Cr2
Y2
t13
06234-008
t14
CONTROL
OUTPUTS
Figure 8. ED (at 54 MHz) Input, 8-/10-Bit 4:2:2 YCrCb (HSYNC/VSYNC), Input Mode 111
CLKIN
t9
t11
3FF
t12
00
00
XY
Cb0
Y0
Cr0
Y1
t13
t14
06234-009
PIXEL PORT
t10
CONTROL
OUTPUTS
Figure 9. ED (at 54 MHz) Input, 8-/10-Bit 4:2:2 YCrCb (EAV/SAV), Input Mode 111
Rev. 0 | Page 11 of 96
ADV7390/ADV7391/ADV7392/ADV7393
Y OUTPUT
b
HSYNC
VSYNC
PIXEL PORT
Y0
Y1
Y2
Y3
PIXEL PORT*
Cb0
Cr0
Cb2
Cr2
a
a = AS PER RELEVANT STANDARD.
06234-010
b = PIPELINE DELAY. PLEASE REFER TO RELEVANT PIPELINE DELAY. THIS CAN BE FOUND IN THE DIGITAL TIMING
SPECIFICATION SECTION OF THE DATA SHEET.
A FALLING EDGE OF HSYNC INTO THE ENCODER GENERATES A SYNC FALLING EDGE ON THE OUTPUT AFTER A TIME
EQUAL TO THE PIPELINE DELAY.
Figure 10. ED-SDR, 16-Bit 4:2:2 YCrCb (HSYNC/VSYNC) Input Timing Diagram
Y OUTPUT
b
HSYNC
VSYNC
Cb0
PIXEL PORT
Y0
Cr0
Y1
a
b = PIPELINE DELAY. PLEASE REFER TO RELEVANT PIPELINE DELAY. THIS CAN BE FOUND IN THE DIGITAL TIMING
SPECIFICATION SECTION OF THE DATA SHEET.
A FALLING EDGE OF HSYNC INTO THE ENCODER GENERATES A SYNC FALLING EDGE ON THE OUTPUT AFTER A TIME
EQUAL TO THE PIPELINE DELAY.
Figure 11. ED-DDR, 8-/10-Bit 4:2:2 YCrCb (HSYNC/VSYNC) Input Timing Diagram
Rev. 0 | Page 12 of 96
06234-011
a(MIN) = 244 CLOCK CYCLES FOR 525p.
a(MIN) = 264 CLOCK CYCLES FOR 625p.
ADV7390/ADV7391/ADV7392/ADV7393
Y OUTPUT
b
HSYNC
VSYNC
PIXEL PORT
Y0
Y1
Y2
Y3
PIXEL PORT
Cb0
Cr0
Cb2
Cr2
a
a = AS PER RELEVANT STANDARD.
06234-012
b = PIPELINE DELAY. PLEASE REFER TO RELEVANT PIPELINE DELAY. THIS CAN BE FOUND IN THE DIGITAL TIMING
SPECIFICATION SECTION OF THE DATA SHEET.
A FALLING EDGE OF HSYNC INTO THE ENCODER GENERATES A FALLING EDGE OF TRI-LEVEL SYNC ON THE OUTPUT
AFTER A TIME EQUAL TO THE PIPELINE DELAY.
Figure 12. HD-SDR, 16-Bit 4:2:2 YCrCb (HSYNC/VSYNC) Input Timing Diagram
Y OUTPUT
b
HSYNC
VSYNC
PIXEL PORT
Cb0
Y0
Cr0
Y1
a
b = PIPELINE DELAY. PLEASE REFER TO RELEVANT PIPELINE DELAY. THIS CAN BE FOUND IN THE DIGITAL TIMING
SPECIFICATION SECTION OF THE DATA SHEET.
A FALLING EDGE OF HSYNC INTO THE ENCODER GENERATES A FALLING EDGE OF TRI-LEVEL SYNC ON THE OUTPUT
AFTER A TIME EQUAL TO THE PIPELINE DELAY.
Figure 13. HD-DDR, 8-/10-Bit 4:2:2 YCrCb (HSYNC/VSYNC) Input Timing Diagram
Rev. 0 | Page 13 of 96
06234-013
a = AS PER RELEVANT STANDARD.
ADV7390/ADV7391/ADV7392/ADV7393
HSYNC
VSYNC
Y
Cr
Y
06234-014
Cb
PIXEL PORT
PAL = 264 CLOCK CYCLES
NTSC = 244 CLOCK CYCLES
Figure 14. SD Input Timing Diagram (Timing Mode 1)
t5
t3
t3
SDA
t6
t1
t2
t7
t4
06234-015
SCL
t8
2
Figure 15. MPU Port Timing Diagram (I C Mode)
SPI_SS
t2
t1
t3
t7
SCLK
t5
X
D7
D6
D5
t6
D4
D3
D2
D1
D0
X
X
X
X
X
X
X
X
D6
D5
D4
D3
D2
D1
D0
t4
MISO
X
X
X
X
X
X
X
X
X
D7
t8
Figure 16. MPU Port Timing Diagram (SPI Mode)
Rev. 0 | Page 14 of 96
06234-016
MOSI
ADV7390/ADV7391/ADV7392/ADV7393
ABSOLUTE MAXIMUM RATINGS
THERMAL RESISTANCE
Table 10.
Parameter1
VAA to AGND
VDD to DGND
PVDD to PGND
VDD_IO to GND_IO
VAA to VDD
VDD to PVDD
VDD_IO to VDD
AGND to DGND
AGND to PGND
AGND to GND_IO
DGND to PGND
DGND to GND_IO
PGND to GND_IO
Digital Input Voltage to GND_IO
Analog Outputs to AGND
Storage Temperature Range (tS)
Junction Temperature (tJ)
Lead Temperature (Soldering, 10 sec)
1
Rating
−0.3 V to +3.9 V
−0.3 V to +2.3 V
−0.3 V to +2.3 V
−0.3 V to +3.9 V
−0.3 V to +2.2 V
−0.3 V to +0.3 V
−0.3 V to +2.2 V
−0.3 V to +0.3 V
−0.3 V to +0.3 V
−0.3 V to +0.3 V
−0.3 V to +0.3 V
−0.3 V to +0.3 V
−0.3 V to +0.3 V
−0.3 V to VDD_IO + 0.3 V
−0.3 V to VAA
−60°C to +100°C
150°C
260°C
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Table 11. Thermal Resistance1
Package Type
32-Lead LFCP
40-Lead LFCSP
1
2
θJA2
27
26
θJC
32
32
Unit
°C/W
°C/W
Values are based on a JEDEC 4 layer test board.
With the exposed metal paddle on the underside of the LFCSP soldered to
the PCB ground.
The ADV739x is a Pb-free product. The lead finish is 100% pure
Sn electroplate. The device is RoHS compliant, suitable for Pbfree applications up to 255°C (±5°C) IR reflow (JEDEC STD-20).
The ADV739x is backward-compatible with conventional SnPb
soldering processes. The electroplated Sn coating can be
soldered with SnPb solder pastes at conventional reflow
temperatures of 220°C to 235°C.
ESD CAUTION
Analog output short circuit to any power supply or common can be of an
indefinite duration.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rev. 0 | Page 15 of 96
ADV7390/ADV7391/ADV7392/ADV7393
32
31
30
29
28
27
26
25
40
39
38
37
36
35
34
33
32
31
GND_IO
P1
P0
DGND
VDD
HSYNC
VSYNC
SFL/MISO
GND_IO
P3
P2
P1
DGND
VDD
P0
HSYNC
VSYNC
SFL/MISO
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
24
23
22
21
20
19
18
17
PIN 1
INDICATOR
ADV7390/
ADV7391
TOP VIEW
(Not to Scale)
RSET
COMP
DAC 1
DAC 2
DAC 3
VAA
AGND
PVDD
VDD_IO 1
P4 2
P5 3
P6 4
P7 5
VDD 6
DGND 7
P8 8
P9 9
P10 10
ADV7392/
ADV7393
30
29
28
27
26
25
24
23
22
21
RSET
COMP
DAC 1
DAC 2
DAC 3
VAA
AGND
PVDD
EXT_LF
PGND
11
12
13
14
15
16
17
18
19
20
TOP VIEW
(Not to Scale)
P11
ALSB/SPI_SS
SDA/SCLK
SCL/MOSI
P12
P13
P14
P15
CLKIN
RESET
06234-017
P7
ALSB/SPI_SS
SDA/SCLK
SCL/MOSI
CLKIN
RESET
PGND
EXT_LF
PIN 1
INDICATOR
Figure 17. ADV7390/ADV7391 Pin Configuration
06234-018
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
VDD_IO
P2
P3
P4
VDD
DGND
P5
P6
Figure 18. ADV7392/ADV7393 Pin Configuration
Table 12. Pin Function Descriptions
Pin Number
ADV7390/91
ADV7392/93
9 to 7, 4 to 2,
31, 30
18 to 15, 11 to 8, 5
to 2, 39 to 37, 34
13
19
Mnemonic
P7 to P0
Input/
Output
I
P15 to P0
I
CLKIN
I
27
33
HSYNC
I/O
26
32
VSYNC
I/O
25
31
SFL/MISO
I/O
24
30
RSET
I
23
22, 21, 20
12
11
10
29
28, 27, 26
14
13
12
COMP
DAC 1, DAC 2, DAC 3
SCL/MOSI
SDA/SCLK
ALSB/SPI_SS
O
O
I
I/O
I
14
20
RESET
I
19
5, 28
25
6, 35
VAA
VDD
P
P
1
17
1
23
VDD_IO
PVDD
P
P
Description
8-Bit Pixel Port (P7 to P0). P0 is the LSB. Refer to Table 30 for input
modes (ADV7390/ADV7391).
16-Bit Pixel Port (P15 to P0). P0 is the LSB. Refer to Table 31 for input
modes (ADV7392/ADV7393).
Pixel Clock Input for HD (74.25 MHz), ED 1 (27 MHz or 54 MHz), or
SD (27 MHz).
Horizontal Synchronization Signal. This pin can also be configured to
output an SD, ED, or HD horizontal synchronization signal. See the
External Horizontal and Vertical Synchronization Control section.
Vertical Synchronization Signal. This pin can also be configured to
output an SD, ED, or HD vertical synchronization signal. See the
External Horizontal and Vertical Synchronization Control section.
Multifunctional Pin: Subcarrier Frequency Lock (SFL) Input/SPI Data
Output (MISO). The SFL input is used to drive the color subcarrier
DDS system, timing reset, or subcarrier reset.
Controls the amplitudes of the DAC 1, DAC 2, and DAC 3 outputs. For
full-drive operation (for example, into a 37.5 Ω load), a 510 Ω resistor
must be connected from RSET to AGND. For low drive operation (for
example, into a 300 Ω load), a 4.12 kΩ resistor must be connected
from RSET to AGND.
Compensation Pin. Connect a 2.2 nF capacitor from COMP to VAA.
DAC Outputs. Full-drive and low-drive capable DACs.
Multifunctional Pin: I2C Clock Input/SPI Data Input.
Multifunctional Pin: I2C Data Input/Output. Also, SPI clock input.
Multifunctional Pin: ALSB sets up the LSB 2 of the MPU I2C
address/SPI slave select (SPI_SS).
Resets the on-chip timing generator and sets the ADV739x into its
default mode.
Analog Power Supply (3.3 V).
Digital Power Supply (1.8 V). For dual-supply configurations, VDD can
be connected to other 1.8 V supplies through a ferrite bead or
suitable filtering.
Input/Output Digital Power Supply (3.3 V).
PLL Power Supply (1.8 V). For dual-supply configurations, PVDD can
be connected to other 1.8 V supplies through a ferrite bead or
suitable filtering.
Rev. 0 | Page 16 of 96
ADV7390/ADV7391/ADV7392/ADV7393
Pin Number
ADV7390/91
ADV7392/93
16
22
15
21
18
24
6, 29
7, 36
32
40
1
2
Mnemonic
EXT_LF
PGND
AGND
DGND
GND_IO
Input/
Output
I
G
G
G
G
Description
External Loop Filter for the Internal PLL.
PLL Ground Pin.
Analog Ground Pin.
Digital Ground Pin.
Input/Output Supply Ground Pin.
ED = enhanced definition = 525p and 625p.
LSB = least significant bit. In the ADV7390, setting the LSB to 0 sets the I2C address to 0xD4. Setting it to 1 sets the I2C address to 0xD6.
In the ADV7391, setting the LSB to 0 sets the I2C address to 0x54. Setting it to 1 sets the I2C address to 0x56.
Rev. 0 | Page 17 of 96
ADV7390/ADV7391/ADV7392/ADV7393
TYPICAL PERFORMANCE CHARACTERISTICS
ED Pr/Pb RESPONSE. LINEAR INTERP FROM 4:2:2 TO 4:4:4
Y RESPONSE IN ED 8× OVERSAMPLING MODE
1.0
0
0.5
–10
0
–0.5
–40
–50
–1.5
–60
–2.0
–70
–2.5
0
20
40
60
80 100 120 140
FREQUENCY (MHz)
160
180
200
–3.0
06234-019
–80
Figure 19. ED 8× Oversampling, PrPb Filter (Linear) Response
0
2
4
6
8
FREQUENCY (MHz)
10
12
Figure 22. ED 8× Oversampling, Y Filter Response (Focus on Pass Band)
ED Pr/Pb RESPONSE. SSAF INTERP FROM 4:2:2 TO 4:4:4
HD Pr/Pb RESPONSE. SSAF INTERP FROM 4:2:2 TO 4:4:4
10
0
0
–10
–10
–20
–20
–30
–30
GAIN (dB)
GAIN (dB)
–1.0
06234-022
–30
GAIN (dB)
GAIN (dB)
–20
–40
–40
–50
–60
–50
–70
–60
–80
–70
20
40
60
80 100 120 140
FREQUENCY (MHz)
160
180
200
–100
Figure 20. ED 8× Oversampling, PrPb Filter (SSAF) Response
0
18.5
37.0
55.5
74.0
92.5
FREQUENCY (MHz)
111.0
129.5
148.0
06234-023
0
06234-020
–80
–90
Figure 23. HD 4× Oversampling, PrPb (SSAF) Filter Response (4:2:2 Input)
HD Pr/Pb RESPONSE. 4:4:4 INPUT MODE
Y RESPONSE IN ED 8× OVERSAMPLING MODE
0
0
–10
–10
–20
–30
GAIN (dB)
–30
–40
–50
–40
–50
–60
–70
–60
–80
–80
0
20
40
60
80 100 120 140
FREQUENCY (MHz)
160
180
Figure 21. ED 8× Oversampling, Y Filter Response
200
–100
10 20 30 40 50 60 70 80 90 100 110 120 130 140
FREQUENCY (MHz)
06234-024
–90
–70
06234-021
GAIN (dB)
–20
Figure 24. HD 4× Oversampling, PrPb (SSAF) Filter Response (4:4:4 Input)
Rev. 0 | Page 18 of 96
ADV7390/ADV7391/ADV7392/ADV7393
Y RESPONSE IN HD 4× OVERSAMPLING MODE
10
0
0
–10
–10
MAGNITUDE (dB)
–20
GAIN (dB)
–30
–40
–50
–60
–20
–30
–40
–50
–70
–80
–60
0
18.5
37.0
55.5
74.0
92.5
FREQUENCY (MHz)
111.0
129.5
148.0
–70
06234-025
–100
0
Figure 25. HD 4× Oversampling, Y Filter Response
2
4
6
8
FREQUENCY (MHz)
10
12
06234-028
–90
Figure 28. SD PAL, Luma Low-Pass Filter Response
Y PASS BAND IN HD 4x OVERSAMPLING MODE
3.0
0
1.5
–10
0
MAGNITUDE (dB)
GAIN (dB)
–1.5
–3.0
–4.5
–6.0
–7.5
–20
–30
–40
–50
–9.0
–60
0
–10
–10
–20
–20
MAGNITUDE (dB)
0
–60
–60
0
2
4
6
8
FREQUENCY (MHz)
10
12
12
–40
–50
–70
10
–30
–50
06234-027
MAGNITUDE (dB)
0
–40
4
6
8
FREQUENCY (MHz)
Figure 29. SD NTSC, Luma Notch Filter Response
Figure 26. HD 4× Oversampling, Y Filter Response (Focus on Pass Band)
–30
2
–70
0
2
4
6
8
FREQUENCY (MHz)
10
Figure 30. SD PAL, Luma Notch Filter Response
Figure 27. SD NTSC, Luma Low-Pass Filter Response
Rev. 0 | Page 19 of 96
12
06234-030
FREQUENCY (MHz)
–70
06234-026
–12.0
27.750 30.063 32.375 34.688 37.000 39.312 41.625 43.937 46.250
06234-029
–10.5
ADV7390/ADV7391/ADV7392/ADV7393
Y RESPONSE IN SD OVERSAMPLING MODE
5
0
4
–10
MAGNITUDE (dB)
GAIN (dB)
–20
–30
–40
–50
3
2
1
–60
0
0
20
40
60
80 100 120 140
FREQUENCY (MHz)
160
180
–1
06234-031
–80
200
0
Figure 31. SD 16× Oversampling, Y Filter Response
2
1
3
4
FREQUENCY (MHz)
5
6
7
06234-034
–70
Figure 34. SD Luma SSAF Filter, Programmable Gain
1
0
0
–20
MAGNITUDE (dB)
MAGNITUDE (dB)
–10
–30
–40
–1
–2
–3
–50
0
2
4
6
8
FREQUENCY (MHz)
10
12
–5
06234-032
–70
2
1
3
4
FREQUENCY (MHz)
5
7
6
Figure 35. SD Luma SSAF Filter, Programmable Attenuation
Figure 32. SD Luma SSAF Filter Response up to 12 MHz
0
4
–10
0
–20
MAGNITUDE (dB)
2
–2
–4
–6
–30
–40
–50
–8
–12
0
1
2
3
4
FREQUENCY (MHz)
5
6
7
–70
0
2
4
6
8
FREQUENCY (MHz)
10
Figure 36. SD Luma CIF Low-Pass Filter Response
Figure 33. SD Luma SSAF Filter, Programmable Responses
Rev. 0 | Page 20 of 96
12
06234-036
–60
–10
06234-033
MAGNITUDE (dB)
0
06234-035
–4
–60
0
–10
–10
–20
–20
–30
–40
–50
–60
–60
4
6
8
FREQUENCY (MHz)
10
12
–70
–10
–10
–20
–20
MAGNITUDE (dB)
0
–30
–40
–60
–60
6
8
FREQUENCY (MHz)
10
12
–70
06234-038
4
6
8
FREQUENCY (MHz)
10
0
2
4
6
8
FREQUENCY (MHz)
10
Figure 41. SD Chroma 1.0 MHz Low-Pass Filter Response
0
0
–10
–10
–20
–20
MAGNITUDE (dB)
Figure 38. SD Chroma 3.0 MHz Low-Pass Filter Response
–30
–40
–40
–60
–60
2
4
6
8
FREQUENCY (MHz)
10
12
06234-039
–50
0
–70
0
2
4
6
8
FREQUENCY (MHz)
10
Figure 42. SD Chroma 0.65 MHz Low-Pass Filter Response
Figure 39. SD Chroma 2.0 MHz Low-Pass Filter Response
Rev. 0 | Page 21 of 96
12
–30
–50
–70
12
–40
–50
2
4
–30
–50
0
2
Figure 40. SD Chroma 1.3 MHz Low-Pass Filter Response
0
–70
0
06234-041
2
12
06234-042
0
Figure 37. SD Luma QCIF Low-Pass Filter Response
MAGNITUDE (dB)
–40
–50
–70
MAGNITUDE (dB)
–30
06234-040
MAGNITUDE (dB)
0
06234-037
MAGNITUDE (dB)
ADV7390/ADV7391/ADV7392/ADV7393
0
–10
–10
–20
–20
–30
–40
–30
–40
–50
–50
–60
–60
–70
0
2
4
6
8
FREQUENCY (MHz)
10
12
Figure 43. SD Chroma CIF Low-Pass Filter Response
–70
0
2
4
6
8
FREQUENCY (MHz)
10
Figure 44. SD Chroma QCIF Low-Pass Filter Response
Rev. 0 | Page 22 of 96
12
06234-044
MAGNITUDE (dB)
0
06234-043
MAGNITUDE (dB)
ADV7390/ADV7391/ADV7392/ADV7393
ADV7390/ADV7391/ADV7392/ADV7393
MPU PORT DESCRIPTION
Devices such as a microprocessor can communicate with the
ADV739x through one of the following protocols:
•
•
2-wire serial (I2C-compatible) bus
4-wire serial (SPI-compatible) bus
After power-up or reset, the MPU port is configured for I2C
operation. SPI operation can be invoked at any time by
following the procedure outlined in the SPI Operation section.
I2C OPERATION
2
The ADV739x supports a 2-wire serial (I C-compatible)
microprocessor bus driving multiple peripherals. This port
operates in an open-drain configuration. Two inputs, serial data
(SDA) and serial clock (SCL), carry information between any
device connected to the bus and the ADV739x. Each slave
device is recognized by a unique address. The ADV739x has
four possible slave addresses for both read and write operations.
These are unique addresses for each device and are illustrated in
Figure 45 and Figure 46. The LSB either sets a read or write
operation. Logic 1 corresponds to a read operation, while Logic
0 corresponds to a write operation. A1 is controlled by setting
the ALSB/SPI_SS pin of the ADV739x to Logic 0 or Logic 1.
1
1
0
1
0
1
A1
ADDRESS
CONTROL
SET UP BY
ALSB/SPI_SS
06234-045
READ/WRITE
CONTROL
WRITE
READ
Figure 45. ADV7390/ADV7392 Slave Address = 0xD4 or 0xD6
0
1
0
1
0
1
A1
Logic 0 on the LSB of the first byte means that the master writes
information to the peripheral. Logic 1 on the LSB of the first byte
means that the master reads information from the peripheral.
The ADV739x acts as a standard slave device on the bus. The
data on the SDA pin is eight bits long, supporting the 7-bit
addresses plus the R/W bit. It interprets the first byte as the
device address and the second byte as the starting subaddress.
There is a subaddress auto-increment facility. This allows data
to be written to or read from registers in ascending subaddress
sequence starting at any valid subaddress. A data transfer is
always terminated by a stop condition. The user can also access
any unique subaddress register on a one-by-one basis without
updating all the registers.
Stop and start conditions can be detected at any stage during
the data transfer. If these conditions are asserted out of
sequence with normal read and write operations, they cause an
immediate jump to the idle condition. During a given SCL high
period, the user should only issue a start condition, a stop
condition, or a stop condition followed by a start condition. If
an invalid subaddress is issued by the user, the ADV739x does
not issue an acknowledge and does return to the idle condition.
If the user utilizes the auto-increment method of addressing the
encoder and exceeds the highest subaddress, the following
actions are taken:
X
0
1
The bits are transferred from MSB down to LSB. The peripheral
that recognizes the transmitted address responds by pulling the
data line low during the ninth clock pulse. This is known as an
acknowledge bit. All other devices withdraw from the bus at
this point and maintain an idle condition. The idle condition is
when the device monitors the SDA and SCL lines waiting for
the start condition and the correct transmitted address. The
R/W bit determines the direction of the data.
X
ADDRESS
CONTROL
•
SET UP BY
ALSB/SPI_SS
READ/WRITE
CONTROL
WRITE
READ
•
06234-046
0
1
Figure 46. ADV7391/ADV7393 Slave Address = 0x54 or 0x56
To control the various devices on the bus, use the following
protocol. The master initiates a data transfer by establishing a
start condition, defined by a high-to-low transition on SDA
while SCL remains high. This indicates that an address/data
stream follows. All peripherals respond to the start condition
and shift the next eight bits (7-bit address + R/W bit).
In read mode, the highest subaddress register contents are
output until the master device issues a no acknowledge.
This indicates the end of a read. A no acknowledge condition
occurs when the SDA line is not pulled low on the ninth pulse.
In write mode, the data for the invalid byte is not loaded
into any subaddress register, a no acknowledge is issued by
the ADV739x, and the part returns to the idle condition.
Figure 47 shows an example of data transfer for a write sequence
and the start and stop conditions. Figure 48 shows bus write
and read sequences.
Rev. 0 | Page 23 of 96
ADV7390/ADV7391/ADV7392/ADV7393
SCL
S
9
1–7
8
START ADDR R/W ACK
9
1–7
8
SUBADDRESS ACK
1–7
DATA
8
9
ACK
P
STOP
06234-047
SDA
Figure 47. I2C Data Transfer
S
SLAVE ADDR
A(S)
SUBADDR
A(S)
DATA
S
SLAVE ADDR
S = START BIT
P = STOP BIT
A(S)
DATA
A(S) P
LSB = 1
LSB = 0
READ
SEQUENCE
A(S)
SUBADDR
A(S) S SLAVE ADDR
A(S) = ACKNOWLEDGE BY SLAVE
A(M) = ACKNOWLEDGE BY MASTER
A(S)
DATA
A(M)
A (S) = NO-ACKNOWLEDGE BY SLAVE
A (M) = NO-ACKNOWLEDGE BY MASTER
DATA
A(M) P
06234-048
WRITE
SEQUENCE
Figure 48. I2C Read and Write Sequence
SPI OPERATION
The ADV739x supports a 4-wire serial (SPI-compatible) bus
connecting multiple peripherals. Two inputs, master out slave in
(MOSI) and serial clock (SCLK), and one output, master in
slave out (MISO), carry information between a master SPI
peripheral on the bus and the ADV739x. Each slave device on
the bus has a slave select pin that is connected to the master SPI
peripheral by a unique slave select line. As such, slave device
addressing is not required.
To invoke SPI operation, a master SPI peripheral (for example, a
microprocessor) should issue three low pulses on the ADV739x
ALSB/SPI_SS pin. When the encoder detects the third rising
edge on the ALSB/SPI_SS pin, it automatically switches to SPI
communication mode. The ADV739x remains in SPI communication mode until a hardware reset or power-down occurs.
To control the ADV739x, use the following protocol for both read
and write transactions. First, the master initiates a data transfer by
driving and holding the ADV739x ALSB/SPI_SS pin low. On the
first SCLK rising edge after ALSB/SPI_SS has been driven low,
the write command, defined as 0xD4, is written to the ADV739x
over the MOSI line. The second byte written to the MOSI line is
interpreted as the starting subaddress. Data on the MOSI line is
written MSB first and clocked on the rising edge of SCLK.
There is a subaddress auto-increment facility. This allows data
to be written to or read from registers in ascending subaddress
sequence starting at any valid subaddress. The user can also
access any unique subaddress register on a one-by-one basis.
In a write data transfer, 8-bit data bytes are written to the
ADV739x, MSB first, on the MOSI line immediately after the
starting subaddress. The data bytes are clocked into the
ADV739x on the rising edge of SCLK. When all data bytes have
been written, the master completes the transfer by driving and
holding the ADV739x ALSB/SPI_SS pin high.
In a read data transfer, after the subaddress has been clocked in
on the MOSI line, the ALSB/SPI_SS pin is driven and held high
for at least one clock cycle. Then, the ALSB/SPI_SS pin is driven
and held low again. On the first SCLK rising edge after
ALSB/SPI_SS has been driven low, the read command, defined
as 0xD5, is written, MSB first, to the ADV739x over the MOSI
line. Subsequently, 8-bit data bytes are read from the ADV739x,
MSB first, on the MISO line. The data bytes are clocked out of
the part on the falling edge of SCLK. When all data bytes have
been read, the master completes the transfer by driving and
holding the ADV739x ALSB/SPI_SS pin high.
Rev. 0 | Page 24 of 96
ADV7390/ADV7391/ADV7392/ADV7393
REGISTER MAP
A microprocessor can read from or write to all registers of the
ADV739x via the MPU port, except for registers that are
specified as read-only or write-only registers.
The subaddress register determines the register accessed by the
next read or write operation. All communication through the
MPU port starts with an access to the subaddress register. A
read/write operation is then performed from/to the target
address, incrementing to the next address until the transaction
is complete.
REGISTER PROGRAMMING
Table 13 to Table 27 describe the functionality of each register.
All registers can be read from as well as written to, unless
otherwise stated.
SUBADDRESS REGISTER (SR7 TO SR0)
The subaddress register is an 8-bit write-only register. After the
MPU port is accessed and a read/write operation is selected, the
subaddress is set up. The subaddress register determines which
register performs the next operation.
Table 13. Register 0x00
SR7 to
SR0
0x00
Register
Power
Mode
Register
Bit Description
Sleep Mode. With this control enabled, the current consumption is
reduced to μA level. All DACs and the internal PLL circuit are
disabled. Registers can be read from and written to in sleep mode.
7
6
Bit Number
5 4 3 2
0
1
DAC 3: Power on/off.
0
1
DAC 2: Power on/off.
0
1
DAC 1: Power on/off.
0
1
0
Rev. 0 | Page 25 of 96
0
0
1
PLL and Oversampling Control. This control allows the internal PLL
circuit to be powered down and the oversampling to be switched off.
Reserved.
1
0
0
Register
Setting
Sleep
mode off.
Sleep
mode on.
PLL on.
PLL off.
DAC 3 off.
DAC 3 on.
DAC 2 off.
DAC 2 on.
DAC 1 off.
DAC 1 on.
Reset
Value
0x12
ADV7390/ADV7391/ADV7392/ADV7393
Table 14. Register 0x01 to Register 0x09
SR7 to
SR0
0x01
Register
Mode Select
Register
Bit Description
Reserved.
DDR Clock Edge Alignment.
Note: Only used for ED 1 and
HD DDR modes.
7
Reserved.
Input Mode.
Note: See Reg. 0x30, Bits[7:3]
for ED/HD format selection.
0x02
Mode
Register 0
Reserved.
Reserved.
Test Pattern Black Bar. 3
6
Bit Number
5 4 3 2
1
0
0
0
1
1
1
0
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0x06
0x07
0x08
0x09
0
0
1
0
1
0
1
0
1
0
1
ED/HD CSC
Matrix 0
ED/HD CSC
Matrix 1
ED/HD CSC
Matrix 2
ED/HD CSC
Matrix 3
ED/HD CSC
Matrix 4
ED/HD CSC
Matrix 5
ED/HD CSC
Matrix 6
SD input.
ED/HD-SDR input 2
ED/HD-DDR input.
Reserved.
Reserved.
Reserved.
Reserved.
ED (at 54 MHz) input.
0
SD Sync Output Enable.
0x05
Chroma clocked in on rising clock edge and
luma clocked in on falling clock edge.
Reserved.
Reserved.
Luma clocked in on rising clock edge and
chroma clocked in on falling clock edge.
0
1
RGB/YPrPb Output Select.
0x04
Reset
Value
0x00
0
Sync on RGB.
0x03
Register Setting
0
0
0
0
0
1
1
1
1
Manual RGB Matrix Adjust.
ED/HD Sync Output Enable.
0
0
x
x
x
x
Zero must be written to these bits.
Disabled.
Enabled.
Disable manual RGB matrix adjust.
Enable manual RGB matrix adjust.
No sync.
Sync on all RGB outputs.
RGB component outputs.
YPrPb component outputs.
No sync output.
Output SD syncs on HSYNC and VSYNC pins.
No sync output.
Output ED/HD syncs on HSYNC and VSYNC
pins.
LSBs for GY.
0x20
0x03
x
x
x
x
x
x
x
x
x
x
x
x
LSBs for RV.
LSBs for BU.
LSBs for GV.
LSBs for GU.
Bits[9:2] for GY.
x
x
x
x
x
x
x
x
Bits[9:2] for GU.
0x0E
x
x
x
x
x
x
x
x
Bits[9:2] for GV.
0x24
x
x
x
x
x
x
x
x
Bits[9:2] for BU.
0x92
x
x
x
x
x
x
x
x
Bits[9:2] for RV.
0x7C
x
x
1
ED = enhanced definition = 525p and 625p.
Available on the ADV7392/ADV7393 (40-pin devices) only.
3
Subaddress 0x31, Bit 2 must also be enabled (ED/HD). Subaddress 0x84, Bit 6 must also be enabled (SD).
2
Rev. 0 | Page 26 of 96
0xF0
0x4E
ADV7390/ADV7391/ADV7392/ADV7393
Table 15. Register 0x0B to Register 0x17
SR7 to
SR0
0x0B
Register
DAC 1, DAC 2,
DAC 3 Output
Level
Bit Description
Positive Gain to DAC Output Voltage.
Negative Gain to DAC Output
Voltage.
0x0D
DAC Power
Mode
7
0
0
0
…
0
0
1
1
1
…
1
6
0
0
0
…
0
1
1
1
0
…
1
5
0
0
0
…
1
0
0
0
0
…
1
Bit Number
4
3
0
0
0
0
0
0
… …
1
1
0
0
0
0
0
0
0
0
… …
1
1
2
0
0
0
…
1
0
0
0
0
…
1
DAC 1 Low Power Mode.
DAC 2 Low Power Mode.
Register Setting
0%
+0.018%
+0.036%
…
+7.382%
+7.5%
−7.5%
−7.382%
−7.364%
…
−0.018%
DAC 1 low power disabled
DAC 1 low power enabled
DAC 2 low power disabled
DAC 2 low power enabled
DAC 3 low power disabled
DAC 3 low power enabled
SD = 16×, ED = 8×
SD = 8×, ED = 4×
0
1
Cable detected on DAC 1
DAC 1 unconnected
Cable detected on DAC 2
DAC 2 unconnected
0
1
SD/ED Oversample Rate Select.
Cable Detection
0
0
1
0
…
1
0
0
1
0
…
1
0
1
0
1
DAC 3 Low Power Mode.
0x10
1
0
0
1
…
1
0
0
0
1
…
1
0
1
Reserved.
DAC 1 Cable Detect.
Read Only.
DAC 2 Cable Detect.
Read Only.
Reserved.
Unconnected DAC auto power-down.
0
0
0
0x14
0x16
Pixel Port
Readback A 1
Pixel Port
Readback B1
Control Port
Readback1
Reserved.
P[7:0] Readback (ADV7390/ADV7391).
0
1
0
Software Reset
DAC auto power-down
disable
DAC auto power-down
enable
0
x
0
x
0
x
x
x
x
x
x
Read only
0xXX
x
x
x
x
x
x
x
x
Read only
0xXX
x
x
x
Read only
0xXX
P[15:8] Readback (ADV7392/ADV7393).
P[7:0] Readback (ADV7392/ADV7393).
Reserved.
VSYNC Readback.
SFL/MISO Readback.
Reserved.
Reserved.
Software Reset.
Reserved.
1
0x00
0
0
x
x
HSYNC Readback.
0x17
0x00
0
1
0x13
Reset
Value
0x00
x
x
x
0
0
1
0
0
0
For correct operation, Subaddress 0x01[6:4] must equal the default value of 000.
Rev. 0 | Page 27 of 96
0
0
0
0x00
Writing a 1 resets the
device; this is a selfclearing bit
ADV7390/ADV7391/ADV7392/ADV7393
Table 16. Register 0x30
SR7 to
SR0
0x30
Register
ED/HD Mode
Register 1
Bit Description
ED/HD Output Standard.
7
6
Bit Number
5 4 3 2
ED/HD Input
Synchronization Format.
1
0
0
0
0
1
1
0
1
1
0
1
ED/HD Input Mode.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
0
1
1
0
0
0
1
0
1
0
1
0
0
0
0
1
1
1
1
0
1
0
0
1
1
0
0
0
0
0
1
0
1
0
1
0
0
0
0
1
1
1
0
1
1
1
0
0
1
0
1
0
0
1
1
1
1
1
1
0
1
1
1
0
0
0
0
0
0
0
1
1
1
0 0 1 0
10011 to 11111
Register Setting
EIA-770.2 output
EIA-770.3 output
EIA-770.1 output
Output levels for full
input range
Reserved
External HSYNC, VSYNC
and field inputs 1
Embedded EAV/SAV
codes
SMPTE 293M, ITU-BT.1358
Nonstandard timing mode
BTA-1004, ITU-BT.1362
ITU-BT.1358
ITU-BT.1362
SMPTE 296M-1,
SMPTE 274M-2
SMPTE 296M-3
SMPTE 296M-4,
SMPTE 274M-5
SMPTE 296M-6
SMPTE 296M-7,
SMPTE 296M-8
SMPTE 240M
Reserved
Reserved
SMPTE 274M-4,
SMPTE 274M-5
SMPTE 274M-6
SMPTE 274M-7,
SMPTE 274M-8
SMPTE 274M-9
SMPTE 274M-10,
SMPTE 274M-11
ITU-R BT.709-5
Reserved
Note
ED
HD
525p @ 59.94 Hz
525p @ 59.94 Hz
625p @ 50 Hz
625p @ 50 Hz
720p @
60 Hz/59.94 Hz
720p @ 50 Hz
720p @
30 Hz/29.97 Hz
720p @ 25 Hz
720p @
24 Hz/23.98 Hz
1035i @
60 Hz/59.94 Hz
1080i @
30 Hz/29.97 Hz
1080i @ 25 Hz
1080p @
30 Hz/29.97 Hz
1080p @ 25 Hz
1080p @
24 Hz/23.98 Hz
1080Psf @ 24 Hz
Synchronization can be controlled with a combination of either HSYNC and VSYNC inputs or HSYNC and field inputs, depending on Subaddress 0x34, Bit 6.
Rev. 0 | Page 28 of 96
Reset
Value
0x00
ADV7390/ADV7391/ADV7392/ADV7393
Table 17. Register 0x31 to Register 0x33
SR7 to
SR0
0x31
Register
ED/HD Mode
Register 2
Bit Description
ED/HD Pixel Data Valid.
7
6
Bit Number
5 4 3 2
HD Oversample Rate Select.
0
1
ED/HD Test Pattern Hatch/Field.
0
1
ED/HD Vertical Blanking Interval (VBI)
Open.
0
1
ED/HD Undershoot Limiter.
0
0
1
1
ED/HD Y Delay with Respect to Falling
Edge of HSYNC.
0
0
0
0
1
ED/HD Color Delay with Respect to
Falling Edge of HSYNC.
0
0
0
0
1
ED/HD CGMS Enable.
ED/HD Mode
Register 4
0
0
1
1
0
0
1
ED/HD Cr/Cb Sequence.
0
1
0
0
1
Sinc Compensation Filter on DAC 1,
DAC 2, DAC 3.
0
1
Reserved.
ED/HD Chroma SSAF Filter.
Reserved.
ED/HD Double Buffering.
0
1
0
1
0
0
1
0
1
0
Reserved.
ED/HD Input Format.
1
0
0
1
1
0
0
1
ED/HD CGMS CRC Enable.
0x33
0
1
0
1
0
1
ED/HD Sharpness Filter.
ED/HD Mode
Register 3
0
0
1
0
1
ED/HD Test Pattern Enable.
0x32
1
0
0
1
1
0
1
Available on the ADV7392/ADV7393 (40-pin devices) only.
Rev. 0 | Page 29 of 96
Register Setting
Pixel data valid off
Pixel data valid on
4×
2×
HD test pattern off
HD test pattern on
Hatch
Field/frame
Disabled
Enabled
Disabled
−11 IRE
−6 IRE
−1.5 IRE
Disabled
Enabled
0 clock cycles
1 clock cycle
2 clock cycles
3 clock cycles
4 clock cycles
0 clock cycles
1 clock cycle
2 clock cycles
3 clock cycles
4 clock cycles
Disabled
Enabled
Disabled
Enabled
Cb after falling edge of HSYNC
Cr after falling edge of HSYNC
0 must be written to this bit
8-bit input
10-bit input 1
Disabled
Enabled
0 must be written to this bit
Disabled
Enabled
1 must be written to this bit
Disable
Enabled
Reset
Value
0x00
0x00
0x68
ADV7390/ADV7391/ADV7392/ADV7393
Table 18. Register 0x34 to Register 0x38
SR7 to
SR0
0x34
Register
ED/HD Mode
Register 5
Bit Description
ED/HD Timing Reset.
7
6
Bit Number
5 4 3 2
ED/HD HSYNC Control. 1
1
0
0 = Field input
1 = VSYNC input
0
1
Update field/line counter
Field/line counter free running
Reserved.
Reserved.
ED/HD Sync on PrPb.
0
0
1
0
1
ED/HD Gamma Correction
Curve Select.
0
1
ED/HD Gamma
Correction Enable.
0
1
ED/HD Adaptive
Filter Mode.
ED/HD Y Level 4
ED/HD Cr Level4
ED/HD Cb Level4
ED/HD Test Pattern Y Level.
ED/HD Test Pattern Cr Level.
ED/HD Test Pattern Cb Level.
0x00
0
ED/HD Color DAC Swap.
0x36
0x37
0x38
ED Macrovision disabled
ED Macrovision enabled
0 must be written to this bit
0
1
ED/HD VSYNC Input/Field
Input.
ED/HD Adaptive
Filter Enable.
Reset
Value
0x48
VSYNC output control (refer to Table 51)
0
1
Reserved.
ED/HD Mode
Register 6
Register Setting
Internal ED/HD timing counters enabled
Resets the internal ED/HD timing counters
HSYNC output control (refer to Table 50)
0
1
Reserved.
ED Macrovision Enable. 2
0x35
0
0
1
0
1
ED/HD VSYNC Control.1
ED/HD Horizontal/Vertical
Counter Mode. 3
1
0
1
0
1
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
1
x
x
x
x
x
x
Disabled
Enabled
DAC 2 = Pb, DAC 3 = Pr
DAC 2 = Pr, DAC 3 = Pb
Gamma Correction Curve A
Gamma Correction Curve B
Disabled
Enabled
Mode A
Mode B
Disabled
Enabled
Y level value
Cr level value
Cb level value
Used in conjunction with ED/HD sync output enable in Subaddress 0x02, Bit 7 = 1.
Applies to the ADV7390 and ADV7392 only.
3
When set to 0, the horizontal/vertical counters automatically wrap around at the end of the line/field/frame of the selected standard. When set to 1, the
horizontal/vertical counters are free running and wrap around when external sync signals indicate to do so.
4
For use with ED/HD internal test patterns only (Subaddress 0x31, Bit 2 = 1).
2
Rev. 0 | Page 30 of 96
0xA0
0x80
0x80
ADV7390/ADV7391/ADV7392/ADV7393
Table 19. Register 0x39 to Register 0x43
SR7 to
SR0
0x39
0x40
0x41
0x42
0x43
Register
ED/HD Mode
Register 7
ED/HD Sharpness
Filter Gain
ED/HD CGMS
Data 0
ED/HD CGMS
Data 1
ED/HD CGMS
Data 2
Bit Description
Reserved.
ED/HD EIA/CEA-861B
Synchronization Compliance.
7
6
Reserved.
ED/HD Sharpness Filter Gain
Value A.
0
ED/HD Sharpness Filter Gain
Value B.
ED/HD CGMS Data Bits.
0
0
…
0
1
…
1
0
0
0
…
1
0
…
1
0
0
0
…
1
0
…
1
0
ED/HD CGMS Data Bits.
C15
C14
ED/HD CGMS Data Bits.
C7
C6
Bit Number
4
3
2
0
0
0
5
1
0
0
0
0
1
Register Setting
Reset
Value
0x00
Disabled
Enabled
0
0
0
…
0
1
…
1
0
0
…
1
0
…
1
0
0
…
1
0
…
1
0
1
…
1
0
…
1
0x00
C16
Gain A = 0
Gain A = +1
…
Gain A = +7
Gain A = −8
…
Gain A = −1
Gain B = 0
Gain B = +1
…
Gain B = +7
Gain B = −8
…
Gain B = −1
CGMS C19 to C16
0
1
…
1
0
…
1
0
C19
C18
C17
C13
C12
C11
C10
C9
C8
CGMS C15 to C8
0x00
C5
C4
C3
C2
C1
C0
CGMS C7 to C0
0x00
0x00
Table 20. Register 0x44 to Register 0x57
SR7 to
SR0
0x44
0x45
0x46
0x47
0x48
0x49
0x4A
0x4B
0x4C
0x4D
0x4E
0x4F
0x50
0x51
0x52
0x53
0x54
0x55
0x56
0x57
Register
ED/HD Gamma A0
ED/HD Gamma A1
ED/HD Gamma A2
ED/HD Gamma A3
ED/HD Gamma A4
ED/HD Gamma A5
ED/HD Gamma A6
ED/HD Gamma A7
ED/HD Gamma A8
ED/HD Gamma A9
ED/HD Gamma B0
ED/HD Gamma B1
ED/HD Gamma B2
ED/HD Gamma B3
ED/HD Gamma B4
ED/HD Gamma B5
ED/HD Gamma B6
ED/HD Gamma B7
ED/HD Gamma B8
ED/HD Gamma B9
Bit Description
ED/HD Gamma Curve A (Point 24).
ED/HD Gamma Curve A (Point 32).
ED/HD Gamma Curve A (Point 48).
ED/HD Gamma Curve A (Point 64).
ED/HD Gamma Curve A (Point 80).
ED/HD Gamma Curve A (Point 96).
ED/HD Gamma Curve A (Point 128).
ED/HD Gamma Curve A (Point 160).
ED/HD Gamma Curve A (Point 192).
ED/HD Gamma Curve A (Point 224).
ED/HD Gamma Curve B (Point 24).
ED/HD Gamma Curve B (Point 32).
ED/HD Gamma Curve B (Point 48).
ED/HD Gamma Curve B (Point 64).
ED/HD Gamma Curve B (Point 80).
ED/HD Gamma Curve B (Point 96).
ED/HD Gamma Curve B (Point 128).
ED/HD Gamma Curve B (Point 160).
ED/HD Gamma Curve B (Point 192).
ED/HD Gamma Curve B (Point 224).
7
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
Rev. 0 | Page 31 of 96
6
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
5
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
Bit Number
4
3
2
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
1
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
0
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
Register
Setting
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
B0
B1
B2
B3
B4
B5
B6
B7
B8
B9
Reset
Value
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
ADV7390/ADV7391/ADV7392/ADV7393
Table 21. Register 0x58 to Register 0x5D
SR7 to
SR0
0x58
0x59
Register
ED/HD Adaptive Filter Gain 1
ED/HD Adaptive Filter Gain 2
Bit Description
ED/HD Adaptive Filter Gain 1,
Value A.
7
6
5
ED/HD Adaptive Filter Gain 1,
Value B.
0
0
…
0
1
…
1
0
0
…
1
0
…
1
0
0
…
1
0
…
1
ED/HD Adaptive Filter Gain 2,
Value A.
ED/HD Adaptive Filter Gain 2,
Value B.
0x5A
ED/HD Adaptive Filter Gain 3
0x5C
0x5D
ED/HD Adaptive Filter
Threshold A
ED/HD Adaptive Filter
Threshold B
ED/HD Adaptive Filter
Threshold C
0
0
…
1
0
…
1
0
0
…
1
0
…
1
ED/HD Adaptive Filter Gain 3,
Value A.
Reset
Value
0x00
x
Register
Setting
Gain A = 0
Gain A = +1
…
Gain A = +7
Gain A = −8
…
Gain A = −1
Gain B = 0
Gain B = +1
…
Gain B = +7
Gain B = −8
…
Gain B = −1
Gain A = 0
Gain A = +1
…
Gain A = +7
Gain A = −8
…
Gain A = −1
Gain B = 0
Gain B = +1
…
Gain B = +7
Gain B = −8
…
Gain B = −1
Gain A = 0
Gain A = +1
…
Gain A = +7
Gain A = −8
…
Gain A = −1
Gain B = 0
Gain B = +1
…
Gain B = +7
Gain B = −8
…
Gain B = −1
Threshold A
2
0
0
…
1
0
…
1
1
0
0
…
1
0
…
1
0
0
1
…
1
0
…
1
0
0
…
1
0
…
1
0
0
…
1
0
…
1
0
1
…
1
0
…
1
0
0
…
1
0
…
1
0
0
…
1
0
…
1
0
1
…
1
0
…
1
x
x
0x00
0x00
ED/HD Adaptive Filter Threshold A.
0
0
…
0
1
…
1
x
0
0
…
1
0
…
1
x
0
0
…
1
0
…
1
x
ED/HD Adaptive Filter Threshold B.
x
x
x
x
x
x
x
x
Threshold B
0x00
ED/HD Adaptive Filter Threshold C.
x
x
x
x
x
x
x
x
Threshold C
0x00
ED/HD Adaptive Filter Gain 3,
Value B.
0x5B
0
0
…
0
1
…
1
Bit Number
4
3
0
0
…
0
1
…
1
0
1
…
1
0
…
1
0
0
…
0
1
…
1
0
1
…
1
0
…
1
0
0
…
0
1
…
1
0
1
…
1
0
…
1
x
x
Rev. 0 | Page 32 of 96
0x00
ADV7390/ADV7391/ADV7392/ADV7393
Table 22. Register 0x5E to Register 0x6E
SR7 to
SR0
0x5E
Register
ED/HD CGMS Type B
Register 0
Bit Description
ED/HD CGMS Type B
Enable.
7
6
5
Bit Number
4
3
2
ED/HD CGMS Type B
CRC Enable.
0x5F
0x60
0x61
0x62
0x63
0x64
0x65
0x66
0x67
0x68
0x69
0x6A
0x6B
0x6C
0x6D
0x6E
ED/HD CGMS Type B
Register 1
ED/HD CGMS Type B
Register 2
ED/HD CGMS Type B
Register 3
ED/HD CGMS Type B
Register 4
ED/HD CGMS Type B
Register 5
ED/HD CGMS Type B
Register 6
ED/HD CGMS Type B
Register 7
ED/HD CGMS Type B
Register 8
ED/HD CGMS Type B
Register 9
ED/HD CGMS Type B
Register 10
ED/HD CGMS Type B
Register 11
ED/HD CGMS Type B
Register 12
ED/HD CGMS Type B
Register 13
ED/HD CGMS Type B
Register 14
ED/HD CGMS Type B
Register 15
ED/HD CGMS Type B
Register 16
ED/HD CGMS Type B
Header Bits.
ED/HD CGMS Type B
Data Bits.
ED/HD CGMS Type B
Data Bits.
ED/HD CGMS Type B
Data Bits.
ED/HD CGMS Type B
Data Bits.
ED/HD CGMS Type B
Data Bits.
ED/HD CGMS Type B
Data Bits.
ED/HD CGMS Type B
Data Bits.
ED/HD CGMS Type B
Data Bits.
ED/HD CGMS Type B
Data Bits.
ED/HD CGMS Type B
Data Bits.
ED/HD CGMS Type B
Data Bits.
ED/HD CGMS Type B
Data Bits.
ED/HD CGMS Type B
Data Bits.
ED/HD CGMS Type B
Data Bits.
ED/HD CGMS Type B
Data Bits.
ED/HD CGMS Type B
Data Bits.
1
0
0
1
0
1
Register
Setting
Disabled
Enabled
Disabled
Enabled
H5 to H0
Reset
Value
0x00
H5
H4
H3
H2
H1
H0
P7
P6
P5
P4
P3
P2
P1
P0
P7 to P0
0x00
P15
P14
P13
P12
P11
P10
P9
P8
P15 to P8
0x00
P23
P22
P21
P20
P19
P18
P17
P16
P23 to P16
0x00
P31
P30
P29
P28
P27
P26
P25
P24
P31 to P24
0x00
P39
P38
P37
P36
P35
P34
P33
P32
P39 to P32
0x00
P47
P46
P45
P44
P43
P42
P41
P40
P47 to P40
0x00
P55
P54
P53
P52
P51
P50
P49
P48
P55 to P48
0x00
P63
P62
P61
P60
P59
P58
P57
P56
P63 to P56
0x00
P71
P70
P69
P68
P67
P66
P65
P64
P71 to P64
0x00
P79
P78
P77
P76
P75
P74
P73
P72
P79 to P72
0x00
P87
P86
P85
P84
P83
P82
P81
P80
P87 to P80
0x00
P95
P94
P93
P92
P91
P90
P89
P88
P95 to P88
0x00
P103
P102
P101
P100
P99
P98
P97
P96
P103 to P96
0x00
P111
P110
P109
P108
P107
P106
P105
P104
P111 to P104
0x00
P119
P118
P117
P116
P115
P114
P113
P112
P119 to P112
0x00
P127
P126
P125
P124
P123
P122
P121
P120
P127 to P120
0x00
Rev. 0 | Page 33 of 96
ADV7390/ADV7391/ADV7392/ADV7393
Table 23. Register 0x80 to Register 0x83
SR7 to
SR0
0x80
Register
SD Mode
Register 1
Bit Description
SD Standard.
7
6
Bit Number
5 4 3 2
SD Luma Filter.
SD Chroma Filter.
0x82
SD Mode
Register 2
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
SD PrPb SSAF Filter.
0
1
0
1
Reserved.
SD Pedestal.
0
1
SD VCR FF/RW Sync.
0
1
SD Pixel Data Valid.
SD Mode
Register 3
0
1
0
1
SD Pedestal YPrPb Output.
0
1
SD Output Levels Y.
0
1
SD Output Levels PrPb.
0
0
1
1
SD Vertical Blanking
Interval (VBI) Open.
0
1
0
1
0
1
SD Closed Captioning
Field Control.
Reserved.
Register Setting
NTSC
PAL B, PAL D, PAL G, PAL H, PAL I
PAL M
PAL N
LPF NTSC
LPF PAL
Notch NTSC
Notch PAL
Luma SSAF
Luma CIF
Luma QCIF
Reserved
1.3 MHz
0.65 MHz
1.0 MHz
2.0 MHz
Reserved
Chroma CIF
Chroma QCIF
3.0 MHz
Disabled
Enabled
Refer to Table 32 in the Output
Configuration section
Reset
Value
0x10
0x0B
0
0
1
SD Square Pixel Mode.
SD Active Video Edge
Control.
0
0
1
0
1
0
1
0
1
0
1
0
1
SD DAC Output 1.
0x83
1
0
0
1
1
0
0
1
1
0
1
0
1
0
Rev. 0 | Page 34 of 96
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
No pedestal on YPrPb
7.5 IRE pedestal on YPrPb
Y = 700 mV/300 mV
Y = 714 mV/286 mV
700 mV p-p (PAL), 1000 mV p-p (NTSC)
700 mV p-p
1000 mV p-p
648 mV p-p
Disabled
Enabled
Closed captioning disabled
Closed captioning on odd field only
Closed captioning on even field only
Closed captioning on both fields
Reserved
0x04
ADV7390/ADV7391/ADV7392/ADV7393
Table 24. Register 0x84 to Register 0x87
SR7 to
SR0
0x84
Register
SD Mode
Register 4
Bit Description
SD VSYNC-3H.
7
6
Bit Number
5 4 3 2
1
0
0
1
1
0
1
0
1
SD SFL/SCR/TR Mode Select.
SD Active Video Length.
0
1
SD Chroma.
0
1
SD Burst.
0
1
SD Color Bars.
0
1
0
1
SD Luma/Chroma Swap.
0x86
SD Mode
Register 5
NTSC Color Subcarrier Adjust (Delay from
the falling edge of output HSYNC pulse to
start of color burst).
Reserved.
SD EIA/CEA-861B Synchronization
Compliance.
0x87
SD Mode
Register 6
0
0
1
0
1
0
1
1
0
1
Disabled
Subcarrier reset mode enabled
Timing reset mode enabled
SFL mode enabled
720 pixels
710 (NTSC), 702 (PAL)
Chroma enabled
Chroma disabled
Enabled
Disabled
Disabled
Enabled
DAC 2 = luma, DAC 3 = chroma
DAC 2 = chroma, DAC 3 = luma
5.17 μs
5.31 μs
5.59 μs (must be set for
Macrovision compliance)
Reserved
Reset
Value
0x00
0x02
0
Disabled
Enabled
0
0
1
0
1
SD PrPb Scale.
0
1
SD Y Scale.
0
1
SD Hue Adjust.
0
1
SD Brightness.
0
1
SD Luma SSAF Gain.
0
1
SD Input Standard Auto Detection.
Reserved.
SD RGB Input Enable.2
Register Setting
Disabled
VSYNC= 2.5 lines (PAL),
VSYNC= 3 lines (NTSC)
0
Reserved.
SD Horizontal/Vertical Counter Mode. 1
SD RGB Color Swap. 2
0
0
1
0
1
0
0
1
1
Update field/line counter
Field/line counter free running
Normal
Color reversal enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
0 must be written to this bit
SD YCrCb input
SD RGB input
When set to 0, the horizontal/vertical counters automatically wrap around at the end of the line/field/frame of the selected standard. When set to 1, the
horizontal/vertical counters are free running and wrap around when external sync signals indicate to do so.
2
Available on the ADV7392/ADV7393 (40-pin devices) only.
Rev. 0 | Page 35 of 96
0x00
ADV7390/ADV7391/ADV7392/ADV7393
Table 25. Register 0x88 to Register 0x89
SR7 to
SR0
0x88
Register
SD Mode
Register 7
Bit Description
Reserved.
SD Noninterlaced Mode.
7
6
Bit Number
5 4 3 2
0
1
SD Input Format.
0
0
1
1
SD Digital Noise Reduction.
SD Mode
Register 8
0
1
0
1
SD Undershoot Limiter.
0
0
1
1
Reserved.
SD Black Burst Output on DAC Luma.
0
0
1
SD Chroma Delay.
Reserved.
1
0
1
0
1
0
1
SD Gamma Correction Enable.
0x89
0
0
0
1
SD Double Buffering.
SD Gamma Correction Curve Select.
1
0
0
1
1
0
0
Available on the ADV7392/ADV7393 (40-pin devices) only.
Rev. 0 | Page 36 of 96
0
1
0
1
0
1
0
1
Register Setting
Disabled
Enabled
Disabled
Enabled
8-bit input
16-bit input 1
10-bit input1
Reserved
Disabled
Enabled
Disabled
Enabled
Gamma Correction Curve A
Gamma Correction Curve B
Disabled
−11 IRE
−6 IRE
−1.5 IRE
0 must be written to this bit
Disabled
Enabled
Disabled
4 clock cycles
8 clock cycles
Reserved
0 must be written to these bits
Reset
Value
0x00
0x00
ADV7390/ADV7391/ADV7392/ADV7393
Table 26. Register 0x8A to Register 0x98
SR7 to
SR0
0x8A
Register
SD Timing Register 0
Bit Description
SD Slave/Master Mode.
7
6
5
Bit Number
4
3
2
1
0
0
1
1
0
1
0
1
SD Timing Mode.
Reserved.
SD Luma Delay.
0
1
0
1
0
1
SD Timing Reset.
SD Timing Register 1
Note: Applicable in
master modes only,
that is, Subaddress
0x8A, Bit 0 = 1.
x
SD HSYNC Width.
SD HSYNC to VSYNC Delay.
SD HSYNC to VSYNC Rising
Edge Delay (Mode 1 Only).
VSYNC Width (Mode 2 Only).
x
x
0
0
1
1
0
1
0
1
0
1
0
0
1
1
0
1
0
1
0
0
1
1
0
1
0
1
0x8C
SD FSC Register 0 1
Subcarrier Frequency Bits[7:0]
0
0
1
1
x
0x8D
SD FSC Register 11
Subcarrier Frequency Bits[15:8]
x
x
x
x
x
x
x
x
0x8E
SD FSC Register 21
Subcarrier Frequency Bits[23:16]
x
x
x
x
x
x
x
x
0x8F
SD FSC Register 31
Subcarrier Frequency Bits[31:24]
x
x
x
x
x
x
x
x
0x90
0x91
0x92
0x93
0x94
0x95
0x96
0x97
0x98
SD FSC Phase
SD Closed Captioning
SD Closed Captioning
SD Closed Captioning
SD Closed Captioning
SD Pedestal Register 0
SD Pedestal Register 1
SD Pedestal Register 2
SD Pedestal Register 3
Subcarrier Phase Bits[9:2]
Extended Data on Even Fields.
Extended Data on Even Fields.
Data on Odd Fields.
Data on Odd Fields.
Pedestal on Odd Fields.
Pedestal on Odd Fields.
Pedestal on Even Fields.
Pedestal on Even Fields.
x
x
x
x
x
17
25
17
25
x
x
x
x
x
16
24
16
24
x
x
x
x
x
15
23
15
23
x
x
x
x
x
14
22
14
22
x
x
x
x
x
13
21
13
21
x
x
x
x
x
12
20
12
20
x
x
x
x
x
11
19
11
19
x
x
x
x
x
10
18
10
18
HSYNC to Pixel Data Adjust.
1
Register Setting
Slave mode
Master mode
Mode 0
Mode 1
Mode 2
Mode 3
Reset
Value
0x08
1
0
0
1
1
SD Minimum Luma Value.
0x8B
0
0
1
0
1
0
1
x
x
x
x
x
x
x
SD subcarrier frequency registers default to NTSC subcarrier frequency values.
Rev. 0 | Page 37 of 96
No delay
2 clock cycles
4 clock cycles
6 clock cycles
−40 IRE
−7.5 IRE
A low-high-low transition
resets the internal SD
timing counters
ta = 1 clock cycle
ta = 4 clock cycles
ta = 16 clock cycles
ta = 128 clock cycles
tb = 0 clock cycles
tb = 4 clock cycles
tb = 8 clock cycles
tb = 18 clock cycles
tc = tb
tc = tb + 32 μs
1 clock cycle
4 clock cycles
16 clock cycles
128 clock cycles
0 clock cycles
1 clock cycle
2 clock cycles
3 clock cycles
Subcarrier Frequency
Bits[7:0]
Subcarrier Frequency
Bits[15:8]
Subcarrier Frequency
Bits[23:16]
Subcarrier Frequency
Bits[31:24]
Subcarrier Phase Bits[9:2]
Extended Data Bits[7:0]
Extended Data Bits[15:8].
Data Bits[7:0]
Data Bits[15:8]
Setting any of these bits
to 1 disables pedestal
on the line number
indicated by the bit
settings
0x00
0x1F
0x7C
0xF0
0x21
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
ADV7390/ADV7391/ADV7392/ADV7393
Table 27. Register 0x99 to Register 0xA5
SR7 to
SR0
0x99
Register
SD CGMS/WSS 0
Bit Description
SD CGMS Data.
SD CGMS CRC.
7
6
SD CGMS on Odd Fields.
0x9A
SD CGMS/WSS 1
SD CGMS/WSS Data.
0x9B
SD CGMS/WSS 2
SD CGMS Data.
SD CGMS/WSS Data.
0x9C
SD Scale LSB
Register
0x9D
0x9E
0x9F
0xA0
0xA1
SD Y Scale Register
SD Cb Scale
Register
SD Cr Scale Register
SD Hue Register
SD Brightness/WSS
0xA2
SD Luma SSAF
0xA3
SD DNR 0
LSBs for SD Y Scale Value.
LSBs for SD Cb Scale Value.
LSBs for SD Cr Scale Value.
LSBs for SD FSC Phase.
SD Y Scale Value.
SD Cb Scale Value.
SD Cr Scale Value.
SD Hue Adjust Value.
SD Brightness Value.
SD Blank WSS Data.
Bit Number
4
3
2
x
x
0
1
1
x
0
x
0
1
SD CGMS on Even Fields.
SD WSS.
5
0
1
0
1
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
0
…
0
…
1
0
…
1
…
1
0
…
1
…
0
0
…
0
…
0
0
0
0
0
0
0
0
0
1
0
0
0
0
1
1
1
1
0
0
0
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
0
1
SD Luma SSAF Gain/Attenuation.
Note: Only applicable if
Subaddress 0x87, Bit 4 = 1.
Reserved.
Coring Gain Border.
Note: In DNR mode, the values
in brackets apply.
0
Coring Gain Data.
Note: In DNR mode, the values
in brackets apply.
0
0
0
0
0
0
0
0
1
0
0
0
0
0
1
1
1
1
0
0
0
0
1
1
0
0
1
1
0
Register Setting
CGMS Data Bits[C19:C16]
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
CGMS Data Bits[C13:C8] or
WSS Data Bits[W13:W8]
CGMS Data Bits[C15:C14]
CGMS Data Bits[C7:C0] or
WSS Data Bits[W7:W0]
SD Y Scale Bits[1:0]
SD Cb Scale Bits[1:0]
SD Cr Scale Bits[1:0]
Subcarrier Phase Bits[1:0]
SD Y Scale Bits[7:2]
SD Cb Scale Bits[7:2]
Reset
Value
0x00
0x00
0x00
0x00
0x00
0x00
SD Cr Scale Bits[7:2]
SD Hue Adjust Bits[7:0]
SD Brightness Bits[6:0]
Disabled
Enabled
−4 dB
…
0 dB
…
+4 dB
0x00
0x00
0x00
No gain
+1/16 [−1/8]
+2/16 [−2/8]
+3/16 [−3/8]
+4/16 [−4/8]
+5/16 [−5/8]
+6/16 [−6/8]
+7/16 [−7/8]
+8/16 [−1]
No gain
+1/16 [−1/8]
+2/16 [−2/8]
+3/16 [−3/8]
+4/16 [−4/8]
+5/16 [−5/8]
+6/16 [−6/8]
+7/16 [−7/8]
+8/16 [−1]
0x00
0x00
0
0
1
0
1
0
1
0
1
0
Rev. 0 | Page 38 of 96
ADV7390/ADV7391/ADV7392/ADV7393
SR7 to
SR0
0xA4
Register
SD DNR 1
Bit Description
DNR Threshold.
7
Border Area.
Block Size.
0xA5
SD DNR 2
6
5
0
0
…
1
1
Bit Number
4
3
0
0
0
0
… …
1
1
1
1
1
0
0
…
1
1
0
0
1
…
0
1
0
0
0
1
0
1
1
0
1
0
1
0
0
1
0
1
DNR Input Select.
DNR Mode.
DNR Block Offset.
2
0
0
…
1
1
0
0
…
1
1
0
0
…
1
1
0
0
…
1
1
7
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
6
x
x
x
x
x
x
x
x
x
x
x
x
X
x
x
x
x
x
x
x
x
0
0
0
1
0
1
…
0
1
Register Setting
0
1
…
62
63
2 pixels
4 pixels
8 pixels
16 pixels
Filter A
Filter B
Filter C
Filter D
DNR mode
DNR sharpness mode
0 pixel offset
1 pixel offset
…
14 pixel offset
15 pixel offset
Reset
Value
0x00
0x00
Table 28. Register 0xA6 to Register 0xBB
SR7 to
SR0
0xA6
0xA7
0xA8
0xA9
0xAA
0xAB
0xAC
0xAD
0xAE
0xAF
0xB0
0xB1
0xB2
0xB3
0xB4
0xB5
0xB6
0xB7
0xB8
0xB9
0xBA
0xBB
Register
SD Gamma A0
SD Gamma A1
SD Gamma A2
SD Gamma A3
SD Gamma A4
SD Gamma A5
SD Gamma A6
SD Gamma A7
SD Gamma A8
SD Gamma A9
SD Gamma B0
SD Gamma B1
SD Gamma B2
SD Gamma B3
SD Gamma B4
SD Gamma B5
SD Gamma B6
SD Gamma B7
SD Gamma B8
SD Gamma B9
SD Brightness Detect
Field Count Register
Bit Description
SD Gamma Curve A (Point 24).
SD Gamma Curve A (Point 32).
SD Gamma Curve A (Point 48).
SD Gamma Curve A (Point 64).
SD Gamma Curve A (Point 80).
SD Gamma Curve A (Point 96).
SD Gamma Curve A (Point 128).
SD Gamma Curve A (Point 160).
SD Gamma Curve A (Point 192).
SD Gamma Curve A (Point 224).
SD Gamma Curve B (Point 24).
SD Gamma Curve B (Point 32).
SD Gamma Curve B (Point 48).
SD Gamma Curve B (Point 64).
SD Gamma Curve B (Point 80).
SD Gamma Curve B (Point 96).
SD Gamma Curve B (Point 128).
SD Gamma Curve B (Point 160).
SD Gamma Curve B (Point 192).
SD Gamma Curve B (Point 224).
SD Brightness Value.
Field Count.
Reserved.
Revision Code.
5
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
0
Rev. 0 | Page 39 of 96
Bit Number
4
3
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
0
0
2
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
1
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
0
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
Register Setting
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
B0
B1
B2
B3
B4
B5
B6
B7
B8
B9
Read only
Read only
Reserved
Read only
Reset
Value
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0xXX
0x0X
ADV7390/ADV7391/ADV7392/ADV7393
Table 29. Register 0xE0 to Register 0xF1
SR7 to
SR0
0xE0
0xE1
0xE2
0xE3
0xE4
0xE5
0xE6
0xE7
0xE8
0xE9
0xEA
0xEB
0xEC
0xED
0xEE
0xEF
0xF0
0xF1
1
Register 1
Macrovision
Macrovision
Macrovision
Macrovision
Macrovision
Macrovision
Macrovision
Macrovision
Macrovision
Macrovision
Macrovision
Macrovision
Macrovision
Macrovision
Macrovision
Macrovision
Macrovision
Macrovision
Bit Description
MV Control Bits.
MV Control Bits.
MV Control Bits.
MV Control Bits.
MV Control Bits.
MV Control Bits.
MV Control Bits.
MV Control Bits.
MV Control Bits.
MV Control Bits.
MV Control Bits.
MV Control Bits.
MV Control Bits.
MV Control Bits.
MV Control Bits.
MV Control Bits.
MV Control Bits.
MV Control Bit.
7
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
0
6
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
0
5
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
0
Bit Number
4
3
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
0
0
Macrovision registers are only available on the ADV7390 and the ADV7392.
Rev. 0 | Page 40 of 96
2
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
0
1
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
0
0
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
Register Setting
Bits[7:1] must be 0
Reset
Value
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
ADV7390/ADV7391/ADV7392/ADV7393
ADV7390/ADV7391 INPUT CONFIGURATION
The ADV7390/ADV7391 supports a number of different input
modes. The desired input mode is selected using Subaddress 0x01,
Bits[6:4]. The ADV7390/ADV7391 defaults to standard
definition (SD) mode upon power-up. Table 30 provides an
overview of all possible input configurations. Each input mode
is described in detail in this section.
P6
P5
P4 P2
YCrCb
YCrCb
YCrCb
P2
P1
P0
P[7:0]
3FF
00
00
XY
Cb0
Y0
Cr0
Y1
06234-050
P7
Whether the Y data is clocked in upon the rising or falling edge
of CLKIN is determined by Subaddress 0x01, Bits[2:1] (see
Figure 50 and Figure 51).
CLKIN
Table 30. ADV7390/ADV7391 Input Configuration
Input Mode
000 SD
010 ED/HD-DDR
111 ED (at 54 MHz)
The CrCb pixel data is also input on Pin P7 to Pin P0
upon the opposite edge of CLKIN. P0 is the LSB.
NOTES
1. SUBADDRESS 0x01 [2:1] SHOULD BE SET TO 00 IN THIS CASE.
Figure 50. ED/HD-DDR Input Sequence (EAV/SAV)—Option A
STANDARD DEFINITION
CLKIN
SD YCrCb data can be input in an interleaved 4:2:2 format over
an 8-bit bus rate of 27 MHz.
A 27 MHz clock signal must be provided on the CLKIN pin. If
required, external synchronization signals can be provided on
the HSYNC and VSYNC pins. Embedded EAV/SAV timing
codes are also supported. The ITU-R BT.601/656 input standard
is supported.
P[7:0]
3FF
Y0
Cb0
Y1
Cr0
MPEG2
DECODER
ADV7390/
ADV7391
CLKIN
YCrCb
YCrCb
8
P[7:0]
INTERLACED TO
PROGRESSIVE
VSYNC,
HSYNC
2
VSYNC,
HSYNC
06234-052
27MHz
XY
Figure 51. ED/HD-DDR Input Sequence (EAV/SAV)—Option B
ADV7390/
ADV7391
2
00
NOTES
1. SUBADDRESS 0x01 [2:1] SHOULD BE SET TO 11 IN THIS CASE.
The interleaved pixel data is input on Pin P7 to Pin P0, with P0
being the LSB.
MPEG2
DECODER
00
06234-051
Subaddress 0x01, Bits[6:4] = 000
CLKIN
8
P[7:0]
ENHANCED DEFINITION (AT 54 MHz)
Subaddress 0x01, Bits[6:4] = 111
Figure 49. SD Example Application
ED YCrCb data can be input in an interleaved 4:2:2 format over
an 8-bit bus rate of 54 MHz.
ENHANCED DEFINITION/HIGH DEFINITION
Subaddress 0x01, Bits[6:4] = 010
A 54 MHz clock signal must be provided on the CLKIN pin.
Embedded EAV/SAV timing codes are supported. External
synchronization signals are not supported in this mode.
ED or HD YCrCb data can be input in an interleaved 4:2:2
format over an 8-bit DDR bus.
The clock signal must be provided on the CLKIN pin. If
required, external synchronization signals can be provided on
the HSYNC and VSYNC pins. Embedded EAV/SAV timing
codes are also supported.
The interleaved pixel data is input on Pin P7 to Pin P0, with P0
being the LSB.
8-Bit 4:2:2 ED/HD YCrCb Mode (DDR)
CLKIN
P[7:0]
In 8-bit DDR 4:2:2 YCrCb input mode, the Y pixel data is input
on Pin P7 to Pin P0 upon either the rising or falling edge of
CLKIN. P0 is the LSB.
Rev. 0 | Page 41 of 96
3FF
00
00
XY
Cb0
Y0
Cr0
Figure 53. ED (At 54 MHz) Input Sequence (EAV/SAV)
Y1
06234-053
YCrCb
06234-049
Figure 52. ED/HD-DDR Example Application
ADV7390/ADV7391/ADV7392/ADV7393
ADV7392/ADV7393 INPUT CONFIGURATION
16-Bit 4:2:2 YCrCb Mode
Subaddress 0x87, Bit 7 = 0
Subaddress 0x88, Bits[4:3] = 01
The ADV7392/ADV7393 supports a number of different input
modes. The desired input mode is selected using Subaddress 0x01,
Bits[6:4]. The ADV7392/ADV7393 defaults to standard
definition (SD) mode upon power-up. Table 31 provides an
overview of all possible input configurations. Each input mode
is described in detail in this section.
In 16-bit 4:2:2 YCrCb input mode, the Y pixel data is input on
Pin P15 to Pin P8, with P8 being the LSB.
The CrCb pixel data is input on Pin P7 to Pin P0, with P0 being
the LSB.
STANDARD DEFINITION
Subaddress 0x01, Bits[6:4] = 000
The pixel data is updated at half the rate of the clock, that is, at a
rate of 13.5 MHz (see Figure 3).
SD YCrCb data can be input in 4:2:2 format over an 8-, 10-, or 16bit bus. SD RGB data can be input in 4:4:4 format over a 16-bit bus.
16-Bit 4:4:4 RGB Mode
Subaddress 0x87, Bit 7 = 1
A 27 MHz clock signal must be provided on the CLKIN pin. If
required, external synchronization signals can be provided on
the HSYNC and VSYNC pins. Embedded EAV/SAV timing
codes are also supported in 8-bit and 10-bit modes.
In 16-bit 4:4:4 RGB input mode, the red pixel data is input on
Pin P4 to Pin P0, the green pixel data is input on Pin P10 to
Pin P5, and the blue pixel data is input on Pin P15 to Pin P11.
P0, P5, and P11 are the respective bus LSBs.
8-Bit 4:2:2 YCrCb Mode
Subaddress 0x87, Bit 7 = 0
Subaddress 0x88, Bits[4:3] = 00
The pixel data is updated at half the rate of the clock, that is, at a
rate of 13.5 MHz (see Figure 4).
In 8-bit 4:2:2 YCrCb input mode, the interleaved pixel data is
input on Pin P15 to Pin P8, with P8 being the LSB. The ITU-R
BT.601/656 input standard is supported.
ADV7392/
ADV7393
10-Bit 4:2:2 YCrCb Mode
Subaddress 0x87, Bit 7 = 0
Subaddress 0x88, Bits[4:3] = 10
27MHz
YCrCb
In 10-bit 4:2:2 YCrCb input mode, the interleaved pixel data is
input on Pin P15 to Pin P6, with P6 being the LSB. The ITU-R
BT.601/656 input standard is supported.
8/10
VSYNC,
HSYNC
CLKIN
06234-054
2
MPEG2
DECODER
P[15:8]/P[15:6]
Figure 54. SD Example Application
Table 31. ADV7392/ADV7393 Input Configuration
Input Mode 1
000
SD 2
8-Bit
10-Bit
16-Bit 3
001
010
111
16-Bit3
ED/HD-SDR (16-Bit)
ED/HD-DDR 4
8-Bit
10-Bit
ED (At 54 MHz)
8-Bit
10-Bit
P15
P14
P13
P12
P11
P10
P9 P8 P7 P6 P5
SD RGB Input Enable (0x87[7]) = 0
P4
P3
P2
YCrCb
YCrCb
Y
CrCb
SD RGB Input Enable (0x87[7]) = 1
G
B
Y
R
CrCb
ED/HD Input Format (0x33[2]) = 0
YCrCb
ED/HD Input Format (0x33[2]) = 1
YCrCb
ED/HD Input Format (0x33[2]) = 0
YCrCb
ED/HD Input Format (0x33[2]) = 1
YCrCb
1
The input mode is determined by Subaddress 0x01, Bits[6:4].
In SD mode, the width of the input data is determined by Subaddress 0x88, Bits[4:3].
External synchronization signals must be used in this input mode. Embedded EAV/SAV timing codes are not supported.
4
ED = enhanced definition = 525p and 625p.
2
3
Rev. 0 | Page 42 of 96
P1
P0
ADV7390/ADV7391/ADV7392/ADV7393
MPEG2
DECODER
Subaddress 0x01, Bits[6:4] = 001 or 010
ED or HD YCrCb data can be input in a 4:2:2 format over an
8-/10-bit DDR bus or a 16-bit SDR bus.
ADV7392/
ADV7393
CLKIN
YCrCb
CrCb 8
The clock signal must be provided on the CLKIN pin. If
required, external synchronization signals can be provided on
the HSYNC and VSYNC pins. Embedded EAV/SAV timing
codes are also supported.
INTERLACED TO
PROGRESSIVE
Y
P[7:0]
8
P[15:8]
2
16-Bit 4:2:2 YCrCb Mode (SDR)
VSYNC
HSYNC
06234-057
ENHANCED DEFINITION/HIGH DEFINITION
Figure 57. ED/HD-SDR Example Application
In 16-bit 4:2:2 YCrCb input mode, the Y pixel data is input on
Pin P15 to Pin P8, with P8 being the LSB.
MPEG2
DECODER
The CrCb pixel data is input on Pin P7 to Pin P0, with P0
being the LSB.
ADV7392/
ADV7393
CLKIN
YCrCb
8-/10-Bit 4:2:2 YCrCb Mode (DDR)
YCrCb 8/10
In 8-/10-bit DDR 4:2:2 YCrCb input mode, the Y pixel data is
input on Pin P15 to Pin P8/P6 upon either the rising or falling
edge of CLKIN. P8/P6 is the LSB.
2
Figure 58. ED/HD-DDR Example Application
10-bit mode is enabled using Subaddress 0x33, Bit 2. Whether
the Y data is clocked in upon the rising or falling edge of CLKIN
is determined by Subaddress 0x01, Bits[2:1] (see Figure 55 and
Figure 56).
00
00
XY
Cb0
Y0
Cr0
Y1
06234-055
NOTES
1. SUBADDRESS 0x01 [2:1] SHOULD BE SET TO 00 IN THIS CASE.
2. 10-BIT MODE IS ENABLED USING SUBADDRESS 0x33, BIT 2.
ENHANCED DEFINITION (AT 54 MHz)
Subaddress 0x01, Bits[6:4] = 111
ED YCrCb data can be input in an interleaved 4:2:2 format on
an 8-/10-bit bus at a rate of 54 MHz.
A 54 MHz clock signal must be provided on the CLKIN pin.
Embedded EAV/SAV timing codes are supported. External
synchronization signals are not supported in this mode.
CLKIN
3FF
VSYNC
HSYNC
06234-058
The CrCb pixel data is also input on Pin P15 to Pin P8/P6
upon the opposite edge of CLKIN. P8/P6 is the LSB.
P[15:8]/
P]15:6]
P[15:8]/P[15:6]
INTERLACED TO
PROGRESSIVE
Figure 55. ED/HD-DDR Input Sequence (EAV/SAV)—Option A
The interleaved pixel data is input on Pin P15 to Pin P8/P6,
with P8/P6 being the LSB.
10-bit mode is enabled using Subaddress 0x33, Bit 2.
CLKIN
CLKIN
00
00
XY
Y0
Cb0
Y1
Cr0
NOTES
1. SUBADDRESS 0x01 [2:1] SHOULD BE SET TO 11 IN THIS CASE.
2. 10-BIT MODE IS ENABLED USING SUBADDRESS 0x33, BIT 2.
3FF
00
00
XY
Cb0
Y0
Cr0
NOTES
1. 10-BIT MODE IS ENABLED USING SUBADDRESS 0x33, BIT 2.
06234-056
3FF
Figure 59. ED (At 54 MHz) Input Sequence (EAV/SAV)
Figure 56. ED/HD-DDR Input Sequence (EAV/SAV)—Option B
MPEG2
DECODER
ADV7392/
ADV7393
54MHz
CLKIN
YCrCb 8/10
INTERLACED TO
PROGRESSIVE
2
P[15:8]/P[15:6]
VSYNC,
HSYNC
Figure 60. ED (At 54 MHz) Example Application
Rev. 0 | Page 43 of 96
06234-060
YCrCb
Y1
06234-059
P[15:8]/P[15:6]
P[15:8]/
P[15:P6]
ADV7390/ADV7391/ADV7392/ADV7393
OUTPUT CONFIGURATION
The ADV739x supports a number of different output configurations. Table 32 to Table 34 lists all possible output configurations.
Table 32. SD Output Configurations
RGB/YPrPb Output Select 1
(0x02, Bit 5)
0
1
1
1
1
SD DAC Output 1
(0x82, Bit 1)
0
0
1
1
SD Luma/Chroma Swap
(0x84, Bit 7)
0
0
0
1
DAC 1
G
Y
CVBS
CVBS
DAC 2
B
Pb
Luma
Chroma
DAC 3
R
Pr
Chroma
Luma
If SD RGB output is selected, a color reversal is possible using Subaddress 0x86, Bit 7.
Table 33. ED/HD Output Configurations
RGB/YPrPb Output Select (0x02, Bit 5)
0
0
1
1
ED/HD Color DAC Swap (0x35, Bit 3)
0
1
0
1
DAC 1
G
G
Y
Y
DAC 2
B
R
Pb
Pr
DAC 3
R
B
Pr
Pb
ED/HD Color DAC Swap (0x35, Bit 3)
0
1
0
1
DAC 1
G
G
Y
Y
DAC 2
B
R
Pb
Pr
DAC 3
R
B
Pr
Pb
Table 34. ED (at 54 MHz) Output Configurations
RGB/YPrPb Output Select (0x02, Bit 5)
0
0
1
1
Rev. 0 | Page 44 of 96
ADV7390/ADV7391/ADV7392/ADV7393
FEATURES
OUTPUT OVERSAMPLING
The ADV739x include an on-chip phase-locked loop (PLL) that
allows for oversampling of SD, ED, and HD video data. By
default, the PLL is disabled. The PLL can be enabled using
Subaddress 0x00, Bit 1 = 0.
Table 35 shows the various oversampling rates supported in the
ADV739x.
ED/HD NONSTANDARD TIMING MODE
Subaddress 0x30, Bits[7:3] = 00001
For any ED/HD input data that does not conform to
the standards listed in the ED/HD input mode table
(Subaddress 0x30, Bits[7:3]), the ED/HD nonstandard
timing mode can be used to interface to the ADV739x.
ED/HD nonstandard timing mode can be enabled by
setting Subaddress 0x30, Bits[7:3] to 00001.
various output levels that can be generated. Table 36 lists the
transitions required to generate the various output levels.
Embedded EAV/SAV timing codes are not supported in
ED/HD nonstandard timing mode.
The user must ensure that appropriate pixel data is applied to
the encoder where the blanking level is expected at the output.
Macrovision (ADV7390/ADV7392 only) and output
oversampling are not available in ED/HD nonstandard timing
mode. The PLL must be disabled (Subaddress 0x00, Bit 1 = 1) in
ED/HD nonstandard timing mode.
ANALOG
OUTPUT
b
ACTIVE VIDEO
a
b
b
BLANKING LEVEL
c
a = TRI-LEVEL SYNCHRONIZATION PULSE LEVEL.
b = BLANKING LEVEL/ACTIVE VIDEO LEVEL.
c = SYNCHRONIZATION PULSE LEVEL.
06234-061
A clock signal must be provided on the CLKIN pin. HSYNC
and VSYNC must be toggled by the user to generate the
appropriate horizontal and vertical synchronization pulses on
the analog output from the encoder. Figure 61 illustrates the
Figure 61. ED/HD Nonstandard Timing Mode Output Levels
Table 35. Output Oversampling Modes and Rates
Input Mode
(0x01, Bits[6:4])
000
SD
000
SD
000
SD
001/010 ED
001/010 ED
001/010 ED
001/010 HD
001/010 HD
001/010 HD
111
ED (at 54 MHz)
111
ED (at 54 MHz)
111
ED (at 54 MHz)
PLL and Oversampling
Control (0x00, Bit 1)
1
0
0
1
0
0
1
0
0
1
0
0
SD/ED Oversample Rate
Select (0x0D, Bit 3)
x
1
0
x
1
0
x
x
x
x
1
0
HD Oversample Rate
Select (0x31, Bit 1)
x
x
x
x
x
x
x
1
0
x
x
x
Oversampling Mode
and Rate
SD (2×)
SD (8×)
SD (16×)
ED (1×)
ED (4×)
ED (8×)
HD (1×)
HD (2×)
HD (4×)
ED (@ 54 MHz) (1×)
ED (@ 54 MHz) (4×)
ED (@ 54 MHz) (8×)
Table 36. ED/HD Nonstandard Timing Mode Synchronization Signal Generation
Output Level Transition 1
HSYNC
VSYNC
b→c
c→a
a→b
c→b
1→0
0
0→1
0→1
1 → 0 or 0 2
0→1
1
0
1
2
a = Tri-level synchronization pulse level; b = blanking level/active video level; c = synchronization pulse level. See Figure 61.
If VSYNC = 1, it should transition to 0. If VSYNC = 0, it should remain at 0. If tri-level synchronization pulse generation is not required, VSYNC should always be 0.
Rev. 0 | Page 45 of 96
ADV7390/ADV7391/ADV7392/ADV7393
•
ED/HD TIMING RESET
Subaddress 0x34, Bit 0
An ED/HD timing reset is achieved by setting the ED/HD
timing reset control bit (Subaddress 0x34, Bit 0) to 1. In this
state, the horizontal and vertical counters remain reset. When
this bit is set back to 0, the internal counters resume counting.
This timing reset applies to the ED/HD timing counters only.
This reset signal must be held high for a minimum of one
clock cycle.
Because the field counter is not reset, it is recommended to
apply the reset signal in Field 7 (PAL) or Field 3 (NTSC).
The reset of the phase then occurs on the next field, that is,
Field 1, which is lined up correctly with the internal
counters. The field count register at Subaddress 0xBB can
be used to identify the number of the active field.
SD SUBCARRIER FREQUENCY LOCK, SUBCARRIER
RESET, AND TIMING RESET
Subaddress 0x84, Bits[2:1]
Together with the SFL/MISO pin and SD Mode Register 4
(Subaddress 0x84, Bits[2:1]), the ADV739x can be used in
timing reset mode, subcarrier phase reset mode, or SFL mode.
•
In timing reset (TR) mode (Subaddress 0x84, Bits[2:1] = 10),
a timing reset is achieved in a low-to-high transition on the
SFL/MISO pin. In this state, the horizontal and vertical
counters remain reset. Upon releasing this pin (set to low),
the internal counters resume counting, starting with Field 1,
and the subcarrier phase is reset.
The minimum time the pin must be held high is one clock
cycle; otherwise, this reset signal may not be recognized.
This timing reset applies to the SD timing counters only.
DISPLAY
307
In subcarrier frequency lock (SFL) mode (Subaddress 0x84,
Bits[2:1] = 11), the ADV739x can be used to lock to an
external video source. The SFL mode allows the ADV739x
to automatically alter the subcarrier frequency to compensate
for line length variations. When the part is connected to a
device such as an ADV7403 video decoder that outputs a
digital data stream in the SFL format, the part automatically
changes to the compensated subcarrier frequency on a
line-by-line basis (see Figure 64). This digital data stream is
67 bits wide and the subcarrier is contained in Bit 0 to Bit
21. Each bit is two clock cycles long.
START OF FIELD 4 OR 8
310
FSC PHASE = FIELD 4 OR 8
313
320
NO TIMING RESET APPLIED
DISPLAY
START OF FIELD 1
1
2
3
4
5
6
7
21
TIMING RESET PULSE
TIMING RESET APPLIED
06234-062
307
FSC PHASE = FIELD 1
Figure 62. SD Timing Reset Timing Diagram (Subaddress 0x84, Bits [2:1] = 10)
DISPLAY
307
310
START OF FIELD 4 OR 8
313
FSC PHASE = FIELD 4 OR 8
320
NO FSC RESET APPLIED
DISPLAY
307
310
START OF FIELD 4 OR 8
313
FSC PHASE = FIELD 1
320
FSC RESET PULSE
FSC RESET APPLIED
Figure 63. SD Subcarrier Phase Reset Timing Diagram (Subaddress 0x84, Bits [2:1] = 01)
Rev. 0 | Page 46 of 96
06234-063
•
In subcarrier reset (SCR) mode (Subaddress 0x84, Bits[2:1]
= 01), a low-to-high transition on the SFL/MISO pin resets
the subcarrier phase to 0 on the field following the
subcarrier phase reset.
ADV7390/ADV7391/ADV7392/ADV7393
ADV739x
CLKIN
DAC 1
LCC1
COMPOSITE
VIDEO1
H/L TRANSITION
COUNT START
SFL
SFL/MISO
DAC 2
DAC 3
ADV7403 P19 TO
VIDEO
DECODER
P10
14 BITS
SUBCARRIER
LOW PHASE
128
13
PIXEL PORT5
4 BITS
RESERVED
0
21
14
19
SEQUENCE
BIT3
FSC PLL INCREMENT2
RESET BIT4
RESERVED
0
RTC
6768
VALID
SAMPLE
INVALID
SAMPLE
1FOR EXAMPLE, VCR OR CABLE.
2F
SC PLL INCREMENT IS 22 BITS LONG. VALUE LOADED INTO ADV73xx FSC DDS REGISTER IS
FSC PLL INCREMENTS BITS 21:0 PLUS BITS 0:9 OF SUBCARRIER FREQUENCY REGISTERS.
3SEQUENCE BIT
8/LINE
LOCKED
CLOCK
5 BITS
RESERVED
PAL: 0 = LINE NORMAL, 1 = LINE INVERTED
NTSC: 0 = NO CHANGE
4RESET ADV739x DDS.
5REFER TO THE ADV7390/ADV7391 AND ADV7392/ADV7393 “INPUT CONFIGURATION” TABLES FOR PIXEL DATA PIN ASSIGNMENTS.
06234-064
TIME SLOT 01
Figure 64. SD Subcarrier Frequency Lock Timing and Connections Diagram (Subaddress 0x84, Bits [2:1] = 11)
Subaddress 0x82, Bit 5
VBI data can be present on Line 10 to Line 20 for NTSC and on
Line 7 to Line 22 for PAL.
In DVD record applications where the encoder is used with a
decoder, the VCR FF/RW sync control bit can be used for nonstandard input video, that is, in fast forward or rewind modes.
In SD Timing Mode 0 (slave option), if VBI is enabled, the
blanking bit in the EAV/SAV code is overwritten. It is possible
to use VBI in this timing mode as well.
In fast forward mode, the sync information at the start of a new
field in the incoming video usually occurs before the correct
number of lines/fields is reached. In rewind mode, this sync
signal usually occurs after the total number of lines/fields is
reached. Conventionally, this means that the output video has
corrupted field signals because one signal is generated by the
incoming video and another is generated when the internal
line/field counters reach the end of a field.
If CGMS is enabled and VBI is disabled, the CGMS data is
nevertheless available at the output.
SD VCR FF/RW SYNC
When the VCR FF/RW sync control is enabled (Subaddress 0x82,
Bit 5), the line/field counters are updated according to the
incoming VSYNC signal and when the analog output matches
the incoming VSYNC signal.
This control is available in all slave-timing modes except
Slave Mode 0.
SD SUBCARRIER FREQUENCY REGISTERS
Subaddress 0x8C to Subaddress 0x8F
Four 8-bit registers are used to set up the subcarrier frequency.
The value of these registers is calculated using the following
equation:
Subcarrier Frequency Register =
Number of subcarrier periods in one video line
Number of 27 MHz clock cycles in one video line
× 2 32
where the sum is rounded to the nearest integer.
For example, in NTSC mode:
227.5 ⎞ 32
Subcarrier Register Value = ⎛⎜
⎟ × 2 = 569408543
⎝ 1716 ⎠
VERTICAL BLANKING INTERVAL
Subaddress 0x31, Bit 4; Subaddress 0x83, Bit 4
The ADV739x is able to accept input data that contains vertical
blanking interval (VBI) data (such as CGMS, WSS, VITS) in
SD, ED, and HD modes.
If VBI is disabled (Subaddress 0x31, Bit 4 for ED/HD;
Subaddress 0x83, Bit 4 for SD), VBI data is not present at the
output and the entire VBI is blanked. These control bits are
valid in all master and slave timing modes.
where:
Subcarrier Register Value = 569408543d = 0×21F07C1F
SD FSC Register 0: 0x1F
SD FSC Register 1: 0x7C
SD FSC Register 2: 0xF0
SD FSC Register 3: 0x21
For the SMPTE 293M (525p) standard, VBI data can be
inserted on Line 13 to Line 42 of each frame, or on Line 6 to
Lind 43 for the ITU-R BT.1358 (625p) standard.
Rev. 0 | Page 47 of 96
ADV7390/ADV7391/ADV7392/ADV7393
Programming the FSC
The subcarrier frequency register value is divided into four FSC
registers as shown in the previous example. The four subcarrier
frequency registers must be updated sequentially, starting with
Subcarrier Frequency Register 0 and ending with Subcarrier
Frequency Register 3. The subcarrier frequency updates only
after the last subcarrier frequency register byte has been
received by the ADV739x.
A 27 MHz clock signal must be provided on the CLKIN pin.
Embedded EAV/SAV timing codes or external horizontal and
vertical synchronization signals provided on the HSYNC and
VSYNC pins can be used to synchronize the input pixel data.
All input configurations, output configurations, and features
available in NTSC and PAL modes are available in SD noninterlaced mode.
Typical FSC Values
For 240p/59.94 Hz input, the ADV739x should be configured for
NTSC operation and Subaddress 0x88, Bit 1 should be set to 1.
Table 37 outlines the values that should be written to the
subcarrier frequency registers for NTSC and PAL B/D/G/H/I.
For 288p/50 Hz input, the ADV739x should be configured for
PAL operation and Subaddress 0x88, Bit 1 should be set to 1.
Table 37. Typical FSC Values
SD SQUARE PIXEL MODE
Description
FSC0
FSC1
FSC2
FSC3
NTSC
0x1F
0x7C
0xF0
0x21
PAL B/D/G/H/I
0xCB
0x8A
0x09
0x2A
Subaddress 0x82, Bit 4
The ADV739x can be used to operate in square pixel mode
(Subaddress 0x82, Bit 4). For NTSC operation, an input clock of
24.5454 MHz is required. Alternatively, for PAL operation, an
input clock of 29.5 MHz is required. The internal timing logic
adjusts accordingly for square pixel mode operation.
SD NONINTERLACED MODE
Subaddress 0x88, Bit 1
The ADV739x supports a SD noninterlaced mode. Using this
mode, progressive inputs at twice the frame rate of NTSC and
PAL (240p/59.94 Hz and 288p/50 Hz, respectively) can be input
into the ADV739x. The SD noninterlaced mode can be enabled
using Subaddress 0x88, Bit 1.
In square pixel mode, the timing diagrams shown in Figure 65
and Figure 66 apply.
ANALOG
VIDEO
EAV CODE
NTSC/PAL M SYSTEM
(525 LINES/60Hz)
PAL SYSTEM
(625 LINES/50Hz)
Y
F 0 0 X 8 1 8 1
C
Y
F 0 0 Y 0 0 0 0
r
4 CLOCK
4 CLOCK
SAV CODE
0 F F A A A
0 F F B B B
C
C
8 1 8 1 F 0 0 X C Y C Y C
Y r Y b
b
0 0 0 0 F 0 0 Y b
r
ANCILLARY DATA
(HANC)
272 CLOCK
4 CLOCK
1280 CLOCK
4 CLOCK
344 CLOCK
1536 CLOCK
06234-065
INPUT PIXELS
START OF ACTIVE
VIDEO LINE
END OF ACTIVE
VIDEO LINE
Figure 65. Square Pixel Mode EAV/SAV Embedded Timing
HSYNC
FIELD
PIXEL
DATA
Cb
Y
Cr
Y
PAL = 308 CLOCK CYCLES
NTSC = 236 CLOCK CYCLES
Figure 66. Square Pixel Mode Active Pixel Timing
Rev. 0 | Page 48 of 96
06234-066
Subaddress
0x8C
0x8D
0x8E
0x8F
ADV7390/ADV7391/ADV7392/ADV7393
EXTENDED (SSAF) PrPb FILTER MODE
FILTERS
0
Table 38 shows an overview of the programmable filters
available on the ADV739x.
–10
Subaddress
0x80
0x80
0x80
0x80
0x80
0x80
0x80
0x80
0x80
0x80
0x80
0x80
0x80
0x80
0x82
0x33
0x33
–20
–30
–40
–50
–60
0
1
2
3
4
FREQUENCY (MHz)
5
6
06234-067
Filter
SD Luma LPF NTSC
SD Luma LPF PAL
SD Luma Notch NTSC
SD Luma Notch PAL
SD Luma SSAF
SD Luma CIF
SD Luma QCIF
SD Chroma 0.65 MHz
SD Chroma 1.0 MHz
SD Chroma 1.3 MHz
SD Chroma 2.0 MHz
SD Chroma 3.0 MHz
SD Chroma CIF
SD Chroma QCIF
SD PrPb SSAF
ED/HD Sinc Compensation Filter
ED/HD Chroma SSAF
GAIN (dB)
Table 38. Selectable Filters
Figure 67. PrPb SSAF Filter
If this filter is disabled, one of the chroma filters shown in
Table 39 can be selected and used for the CVBS or luma/
chroma signal.
Table 39. Internal Filter Specifications
SD Internal Filter Response
Subaddress 0x80, Bits[7:2]; Subaddress 0x82, Bit 0
The Y filter supports several different frequency responses,
including two low-pass responses, two notch responses, an
extended (SSAF) response with or without gain boost
attenuation, a CIF response, and a QCIF response. The PrPb
filter supports several different frequency responses, including
six low-pass responses, a CIF response, and a QCIF response, as
shown in Figure 36 and Figure 37.
If SD Luma SSAF gain is enabled (Subaddress 0x87, Bit 4), there
are 13 response options in the range −4 dB to +4 dB. The desired
response can be programmed using Subaddress 0xA2. The
variation of frequency responses are shown in Figure 33 to
Figure 35.
In addition to the chroma filters listed in Table 38, the ADV739x
contains an SSAF filter specifically designed for the color difference
component outputs, Pr and Pb. This filter has a cutoff frequency
of ~2.7 MHz and a gain of –40 dB at 3.8 MHz (see Figure 67).
This filter can be controlled with Subaddress 0x82, Bit 0.
Filter
Luma LPF NTSC
Luma LPF PAL
Luma Notch NTSC
Luma Notch PAL
Luma SSAF
Luma CIF
Luma QCIF
Chroma 0.65 MHz
Chroma 1.0 MHz
Chroma 1.3 MHz
Chroma 2.0 MHz
Chroma 3.0 MHz
Chroma CIF
Chroma QCIF
1
Pass-Band
Ripple (dB)1
0.16
0.1
0.09
0.1
0.04
0.127
Monotonic
Monotonic
Monotonic
0.09
0.048
Monotonic
Monotonic
Monotonic
3 dB Bandwidth (MHz)2
4.24
4.81
2.3/4.9/6.6
3.1/5.6/6.4
6.45
3.02
1.5
0.65
1
1.395
2.2
3.2
0.65
0.5
Pass-band ripple is the maximum fluctuation from the 0 dB response in the
pass band, measured in dB. The pass band is defined to have 0 Hz to fc (Hz)
frequency limits for a low-pass filter, and 0 Hz to f1 (Hz) and f2 (Hz) to infinity
for a notch filter, where fc, f1, and f2 are the −3 dB points.
2
3 dB bandwidth refers to the −3 dB cutoff frequency.
Rev. 0 | Page 49 of 96
ADV7390/ADV7391/ADV7392/ADV7393
ED/HD Sinc Compensation Filter Response
Subaddress 0x33, Bit 3
The ADV739x includes a filter designed to counter the effect of
sinc roll-off in DAC 1, DAC 2, and DAC 3 while operating in
ED/HD mode. This filter is enabled by default. It can be
disabled using Subaddress 0x33, Bit 3. The benefit of the filter is
illustrated in Figure 68 and Figure 69.
0.5
0.4
0.3
GAIN (dB)
0.2
0.1
0
Table 40 shows sample color values that can be programmed
into the color registers when the output standard selection is set
to EIA770.2/EIA770.3 (Subaddress 0x30, Bits[1:0] = 00).
Table 40. Sample Color Values for EIA770.2/EIA770.3
ED/HD Output Standard Selection
Sample Color
White
Black
Red
Green
Blue
Yellow
Cyan
Magenta
Y Value
235 (0xEB)
16
(0x10)
81
(0x51)
145 (0x91)
41
(0x29)
210 (0xD2)
170 (0xAA)
106 (0x6A)
Cr Value
128 (0x80)
128 (0x80)
240 (0xF0)
34
(0x22)
110 (0x6E)
146 (0x92)
16
(0x10)
222 (0xDE)
Cb Value
128 (0x80)
128 (0x80)
90
(0x5A)
54
(0x36)
240 (0xF0)
16
(0x10)
166 (0xA6)
202 (0xCA)
–0.1
–0.2
COLOR SPACE CONVERSION MATRIX
–0.3
Subaddress 0x03 to Subaddress 0x09
–0.5
0
5
10
15
20
FREQUENCY (MHz)
25
30
06234-068
–0.4
Figure 68. ED/HD Sinc Compensation Filter Enabled
0.5
The internal color space conversion (CSC) matrix automatically
performs all color space conversions based on the input mode
programmed in the mode select register (Subaddress 0x01,
Bits[6:4]). Table 41 and Table 42 show the options available in
this matrix.
An SD color space conversion from RGB-in to YPrPb-out is
possible on the ADV7392/ADV7393. An ED/HD color space
conversion from RGB-in to YPrPb-out is not possible.
0.4
0.3
GAIN (dB)
0.2
Table 41. SD Color Space Conversion Options
0.1
0
Input
YCrCb
YCrCb
RGB2
RGB2
–0.1
–0.2
–0.3
–0.4
0
5
10
15
20
FREQUENCY (MHz)
25
30
06234-069
1
–0.5
2
Output1
YPrPb
RGB
YPrPb
RGB
YPrPb/RGB Out
(Reg. 0x02, Bit 5)
1
0
1
0
RGB In/YCrCb In
(Reg. 0x87, Bit 7)
0
0
1
1
CVBS/YC outputs are available for all CSC combinations.
Available on the ADV7392/ADV7393 (40-pin devices) only.
Table 42. ED/HD Color Space Conversion Options
Figure 69. ED/HD Sinc Compensation Filter Disabled
Input
YCrCb
YCrCb
ED/HD TEST PATTERN COLOR CONTROLS
Subaddress 0x36 to Subaddress 0x38
Three 8-bit registers at Subaddress 0x36 to Subaddress 0x38
are used to program the output color of the internal ED/HD
test pattern generator (Subaddress 0x31, Bit 2 = 1), whether it
be the lines of the cross hatch pattern or the uniform field test
pattern. They are not functional as color controls for external
pixel data input.
The values for the luma (Y) and color difference (Cr and Cb)
signals used to obtain white, black, and saturated primary and
complementary colors conform to the ITU-R BT.601-4
standard.
Output
YPrPb
RGB
YPrPb/RGB Out (Reg. 0x02, Bit 5)
1
0
ED/HD Manual CSC Matrix Adjust Feature
The ED/HD manual CSC matrix adjust feature provides custom
coefficient manipulation for color space conversions and is used
in ED and HD modes only. The ED/HD manual CSC matrix
adjust feature can be enabled using Subaddress 0x02, Bit 3.
Normally, there is no need to enable this feature because the CSC
matrix automatically performs the color space conversion based
on the input mode chosen (ED or HD) and the output color
space selected (see Table 42). For this reason, the ED/HD
manual CSC matrix adjust feature is disabled by default.
Rev. 0 | Page 50 of 96
ADV7390/ADV7391/ADV7392/ADV7393
If RGB output is selected, the ED/HD CSC matrix scalar uses
the following equations:
For example, SMPTE 293M uses the following conversion:
R = Y + 1.402Pr
R = GY × Y + RV × Pr
G = Y − 0.714Pr − 0.344Pb
G = GY × Y − (GU × Pb) − (GV × Pr)
B = Y + 1.773Pb
B = GY × Y + BU × Pb
Note that subtractions are implemented in hardware.
If YPrPb output is selected, the following equations are used:
Programming the CSC Matrix
Y = GY × Y
If custom manipulation of the ED/HD CSC matrix coefficients
is required for a YCrCb-to-RGB color space conversion, follow
the following procedure:
Pr = RV × Pr
Pb = BU × Pb
where:
GY = Subaddress 0x05, Bits[7:0] and Subaddress 0x03, Bits[1:0].
GU = Subaddress 0x06, Bits[7:0] and Subaddress 0x04, Bits[7:6].
GV = Subaddress 0x07, Bits[7:0] and Subaddress 0x04, Bits[5:4].
BU = Subaddress 0x08, Bits[7:0] and Subaddress 0x04, Bits[3:2].
RV = Subaddress 0x09, Bits[7:0] and Subaddress 0x04, Bits[1:0].
1.
Enable the ED/HD manual CSC matrix adjust feature
(Subaddress 0x02, Bit 3).
2.
Set the output to RGB (Subaddress 0x02, Bit 5).
3.
Disable sync on PrPb (Subaddress 0x35, Bit 2).
4.
Enable sync on RGB (optional) (Subaddress 0x02, Bit 4).
The GY value controls the green signal output level, the BU
value controls the blue signal output level, and the RV value
controls the red signal output level.
Upon power-up, the CSC matrix is programmed with the
default values shown in Table 43.
Table 43. ED/HD Manual CSC Matrix Default Values
Subaddress
0x03
0x04
0x05
0x06
0x07
0x08
0x09
The programmable CSC matrix is used for external ED/HD
pixel data and is not functional when internal test patterns are
enabled.
SD LUMA AND COLOR CONTROL
Default
0x03
0xF0
0x4E
0x0E
0x24
0x92
0x7C
Subaddress 0x9C to Subaddress 0x9F
SD Y Scale, SD Cb Scale, and SD Cr Scale are three 10-bit
control registers that scale the SD Y, Cb, and Cr output levels.
Each of these registers represent the value required to scale the
Cb or Cr level from 0.0 to 2.0 and the Y level from 0.0 to 1.5
times its initial level. The value of these 10 bits is calculated
using the following equation:
When the ED/HD manual CSC matrix adjust feature is
enabled, the default coefficient values in Subaddress 0x03
to Subaddress 0x09 are correct for the HD color space only.
The color components are converted according to the following
1080i and 720p standards (SMPTE 274M, SMPTE 296M):
Y, Cb, or Cr Scale Value = Scale Factor × 512
For example, if Scale Factor = 1.3
Y, Cb, or Cr Scale Value = 1.3 × 512 = 665.6
Y, Cb, or Cr Scale Value = 666 (rounded to the nearest integer)
Y, Cb, or Cr Scale Value = 1010 0110 10b
R = Y + 1.575Pr
G = Y − 0.468Pr − 0.187Pb
B = Y + 1.855Pb
The conversion coefficients should be multiplied by 315 before
being written to the ED/HD CSC matrix registers. This is
reflected in the default values for GY = 0x13B, GU = 0x03B,
GV = 0x093, BU = 0x248, and RV = 0x1F0.
Subaddress 0x9C, SD Scale LSB Register = 0x2A
Subaddress 0x9D, SD Y Scale Register = 0xA6
Subaddress 0x9E, SD Cb Scale Register = 0xA6
Subaddress 0x9F, SD Cr Scale Register = 0xA6
Note that this feature affects all interlaced output signals, that is,
CVBS, Y-C, YPrPb, and RGB.
If the ED/HD manual CSC matrix adjust feature is enabled and
another input standard (such as ED) is used, the scale values for
GY, GU, GV, BU, and RV must be adjusted according to this
input standard color space. The user should consider that the
color component conversion might use different scale values.
Rev. 0 | Page 51 of 96
ADV7390/ADV7391/ADV7392/ADV7393
For NTSC with pedestal, the setup can vary from 0 IRE to 22.5 IRE.
For NTSC without pedestal (see Figure 70) and for PAL, the
setup can vary from −7.5 IRE to +15 IRE.
SD HUE ADJUST CONTROL
Subaddress 0xA0
When enabled, the SD hue adjust control register
(Subaddress 0xA0) is used to adjust the hue on the SD
composite and chroma outputs. This feature can be
enabled using Subaddress 0x87, Bit 2.
The SD brightness control register is an 8-bit register. The seven
LSBs of this 8-bit register are used to control the brightness
level, which can be a positive or negative value.
Subaddress 0xA0 contains the bits required to vary the hue of
the video data, that is, the variance in phase of the subcarrier
during active video with respect to the phase of the subcarrier
during the color burst. The ADV739x provides a range of
±22.5° in increments of 0.17578125°. For normal operation
(zero adjustment), this register is set to 0x80. Values 0xFF and
0x00 represent the upper and lower limits, respectively, of the
attainable adjustment in NTSC mode. Values 0xFF and 0x01
represent the upper and lower limits, respectively, of the
attainable adjustment in PAL mode.
For example,
To add +20 IRE brightness level to an NTSC signal with
pedestal, write 0x28 to Subaddress 0xA1.
0 × (SD Brightness Value) =
0 × (IRE Value × 2.015631) =
0 × (20 × 2.015631) = 0 × (40.31262) ≈ 0x28
To add –7 IRE brightness level to a PAL signal, write 0x72 to
Subaddress 0xA1.
0 × (SD Brightness Value) =
The hue adjust value is calculated using the following equation:
0 × (IRE Value × 2.075631) =
Hue Adjust (°) = 0.17578125° (HCRd − 128)
0 × (7 × 2.015631) = 0x(14.109417) ≈ 0001110b
where = HCRd hue adjust control register (decimal)
0001110b into two’s complement = 1110010b = 0x72
For example, to adjust the hue by +4°, write 0x97 to the hue
adjust control register:
Table 44. Sample Brightness Control Values1
4
⎛
⎞ + 128 ≈ 151d = 0 x 97
⎜
⎟
⎝ 0.17578125 ⎠
where the sum is rounded to the nearest integer.
To adjust the hue by −4°, write 0x69 to the hue adjust control
register:
−4
⎛
⎜
⎝ 0.17578125
⎞ + 128 ≈ 105d = 0 x 69
⎟
⎠
Setup Level
(NTSC) with
Pedestal
22.5 IRE
15 IRE
7.5 IRE
0 IRE
1
Setup Level
(NTSC) Without
Pedestal
15 IRE
7.5 IRE
0 IRE
−7.5 IRE
Setup
Level
(PAL)
15 IRE
7.5 IRE
0 IRE
−7.5 IRE
Brightness
Control Value
0x1E
0x0F
0x00
0x71
Values in the range of 0x3F to 0x44 can result in an invalid output signal.
SD INPUT STANDARD AUTO DETECTION
where the sum is rounded to the nearest integer.
Subaddress 0x87, Bit 5
SD BRIGHTNESS DETECT
The ADV739x include an SD input standard auto detect feature
that can be enabled by setting Subaddress 0x87, Bit 5 to Bit 1.
Subaddress 0xBA
The ADV739x allows monitoring of the brightness level of the
incoming video data. The SD brightness detect register
(Subaddress 0xBA) is a read-only register.
Subaddress 0xA1, Bits[6:0]
When enabled, the ADV739x can automatically identify an
NTSC or PAL B/D/G/H/I input stream. The ADV739x
automatically updates the subcarrier frequency registers with
the appropriate value for the identified standard. The ADV739x
is also configured to correctly encode the identified standard.
When this feature is enabled, the SD brightness/WSS control
register (Subaddress 0xA1) is used to control brightness by
adding a programmable setup level onto the scaled Y data. This
feature can be enabled using Subaddress 0x87, Bit 3.
The SD standard bits (Subaddress 0x80, Bits[1:0]) and the
subcarrier frequency registers are not updated to reflect the
identified standard. All registers retain their default or userdefined values.
SD BRIGHTNESS CONTROL
NTSC WITHOUT PEDESTAL
+7.5 IRE
100 IRE
0 IRE
NO SETUP
VALUE ADDED
NEGATIVE SETUP
VALUE ADDED
Figure 70. Examples of Brightness Control Values
Rev. 0 | Page 52 of 96
06234-070
–7.5 IRE
POSITIVE SETUP
VALUE ADDED
ADV7390/ADV7391/ADV7392/ADV7393
DOUBLE BUFFERING
Subaddress 0x33, Bit 7 for ED/HD,
Subaddress 0x88, Bit 2 for SD
Double-buffered registers are updated once per field. Double
buffering improves overall performance because modifications
to register settings are not be made during active video, but take
effect prior to the start of the active video on the next field.
Using Subaddress 0x33, Bit 7, double buffering can be activated
on the following ED/HD registers: ED/HD Gamma A and
Gamma B curves, and ED/HD CGMS registers.
Using Subaddress 0x88, Bit 2, double buffering can be activated
on the following SD registers: SD Gamma A and Gamma B curves,
SD Y scale, SD Cr scale, SD Cb scale, SD brightness, SD closed
captioning, and SD Macrovision Bits[5:0] (Subaddress 0xE0,
Bits[5:0]).
PROGRAMMABLE DAC GAIN CONTROL
Subaddress 0x0B
It is possible to adjust the DAC output signal gain up or down
from its absolute level. This is illustrated in Figure 71.
DAC 1 to DAC 3 are controlled by Register 0x0B.
CASE A
GAIN PROGRAMMED IN DAC OUTPUT LEVEL
REGISTERS, SUBADDRESS 0x0B
700mV
The range of this feature is specified for ±7.5% of the nominal
output from the DACs. For example, if the output current of the
DAC is 4.33 mA, the DAC gain control feature can change this
output current from 4.008 mA (−7.5%) to 4.658 mA (+7.5%).
The reset value of the control registers is 0x00, that is, nominal
DAC current is output. Table 45 is an example of how the
output current of the DACs varies for a nominal 4.33 mA
output current.
Table 45. DAC Gain Control
Subaddress 0x0B
0100 0000 (0x40)
0011 1111 (0x3F)
0011 1110 (0x3E)
...
...
0000 0010 (0x02)
0000 0001 (0x01)
0000 0000 (0x00)
DAC Current
(mA)
4.658
4.653
4.648
...
...
4.43
4.38
4.33
% Gain
7.5000%
7.3820%
7.3640%
...
...
0.0360%
0.0180%
0.0000%
1111 1111 (0xFF)
1111 1110 (0xFE)
...
...
1100 0010 (0xC2)
1100 0001 (0xC1)
1100 0000 (0xC0)
4.25
4.23
...
...
4.018
4.013
4.008
−0.0180%
−0.0360%
...
...
−7.3640%
−7.3820%
−7.5000%
Note
Reset value,
nominal
GAMMA CORRECTION
300mV
CASE B
In Case B of Figure 71, the video output signal is reduced. The
absolute level of the sync tip and blanking level both decrease
with respect to the reference video output signal. The overall
gain of the signal is reduced from the reference signal.
Subaddress 0x44 to Subaddress 0x57 for ED/HD,
Subaddress 0xA6 to Subaddress 0xB9 for SD
NEGATIVE GAIN PROGRAMMED IN
DAC OUTPUT LEVEL REGISTERS,
SUBADDRESS 0x0B
700mV
Generally, gamma correction is applied to compensate for the
nonlinear relationship between signal input and output
brightness level (as perceived on a CRT). It can also be applied
wherever nonlinear processing is used.
Gamma correction uses the function
300mV
06234-071
SignalOUT = (SignalIN)γ
Figure 71. Programmable DAC Gain—Positive and Negative Gain
In Case A of Figure 71, the video output signal is gained. The
absolute level of the sync tip and blanking level both increase
with respect to the reference video output signal. The overall
gain of the signal is increased from the reference signal.
where γ = gamma correction factor.
Gamma correction is available for SD and ED/HD video. For
both variations, there are 20, 8-bit registers. They are used to
program Gamma Correction Curve A and Curve B.
ED/HD gamma correction is enabled using Subaddress 0x35,
Bit 5. ED/HD Gamma Correction Curve A is programmed at
Subaddress 0x44 to Subaddress 0x4D, and ED/HD Gamma
Correction Curve B is programmed at Subaddress 0x4E to
Subaddress 0x57.
Rev. 0 | Page 53 of 96
ADV7390/ADV7391/ADV7392/ADV7393
SD gamma correction is enabled using Subaddress 0x88, Bit 6.
SD Gamma Correction Curve A is programmed at Subaddress
0xA6 to Subaddress 0xAF, and SD Gamma Correction Curve B
is programmed at Subaddress 0xB0 to Subaddress 0xB9.
To program the gamma correction registers, calculate the
10 programmable curve values using the following formula:
⎛ n − 16 ⎞ γ
⎞
γ n = ⎜⎜ ⎛⎜
⎟ × (240 − 16) ⎟⎟ + 16
⎝ ⎝ 240 − 16 ⎠
⎠
Gamma correction is performed on the luma data only. The
user can choose one of two correction curves, Curve A or
Curve B. Only one of these curves can be used at a time. For
ED/HD gamma correction, curve selection is controlled using
Subaddress 0x35, Bit 4. For SD gamma correction, curve
selection is controlled using Subaddress 0x88, Bit 7.
where:
γn = value to be written into the gamma correction register for
point n on the gamma correction curve
n = 24, 32, 48, 64, 80, 96, 128, 160, 192, or 224
γ = gamma correction factor
The shape of the gamma correction curve is controlled by
defining the curve response at 10 different locations along the
curve. By altering the response at these locations, the shape of
the gamma correction curve can be modified. Between these
points, linear interpolation is used to generate intermediate
values. Considering the curve to have a total length of 256
points, the 10 programmable locations are at points 24, 32, 48,
64, 80, 96, 128, 160, 192, and 224. Locations 0, 16, 240, and 255
are fixed and cannot be changed.
For example, setting γ = 0.5 for all programmable curve data
points results in the following yn values:
y24 = [(8/224)0.5 × 224] + 16 = 58
y32 = [(16/224)0.5 × 224] + 16 = 76
y48 = [(32/224)0.5 × 224] + 16 = 101
y64 = [(48/224)0.5 × 224] + 16 = 120
y80 = [(64/224)0.5 × 224] + 16 = 136
y96 = [(80/224)0.5 × 224] + 16 = 150
From curve locations 16 to 240, the values at the programmable
locations and, therefore, the response of the gamma correction
curve, should be calculated to produce the following result:
y128 = [(112/224)0.5 × 224] + 16 = 174
y160 = [(144/224)0.5 × 224] + 16 = 195
y192 = [(176/224)0.5 × 224] + 16 = 214
xDESIRED = (xINPUT)γ
y224 = [(208/224)0.5 × 224] + 16 = 232
where:
xDESIRED = desired gamma corrected output
xINPUT = linear input signal
γ = gamma correction factor
where the sum of each equation is rounded to the nearest integer.
The gamma curves in Figure 72 and Figure 73 are examples only;
any user-defined curve in the range from 16 to 240 is acceptable.
GAMMA CORRECTION BLOCK OUTPUT TO A RAMP INPUT
300
GAMMA CORRECTION BLOCK TO A RAMP INPUT FOR
VARIOUS GAMMA VALUES
250
0.5
150
100
SIGNAL INPUT
50
0
0
50
100
150
LOCATION
200
250
250
0.5
150
100
SI
I
AL
GN
UT
NP
1.5
1.8
50
0
Figure 72. Signal Input (Ramp) and Signal Output for Gamma 0.5
0.3
200
0
50
100
150
LOCATION
200
250
Figure 73. Signal Input (Ramp) and Selectable Output Curves
Rev. 0 | Page 54 of 96
06234-073
200
GAMMA CORRECTED AMPLITUDE
SIGNAL OUTPUT
06234-072
GAMMA CORRECTED AMPLITUDE
300
ADV7390/ADV7391/ADV7392/ADV7393
ED/HD SHARPNESS FILTER AND ADAPTIVE FILTER
CONTROLS
Subaddress 0x40, Subaddress 0x58 to Subaddress 0x5D
There are three filter modes available on the ADV739x:
sharpness filter mode and two adaptive filter modes.
ED/HD Sharpness Filter Mode
The derivative of the incoming signal is compared to the three
programmable threshold values: ED/HD Adaptive Filter
Threshold A, Threshold B, and Threshold C (Subaddress 0x5B,
Subaddress 0x5C, and Subaddress 0x5D). The recommended
threshold range is 16 to 235, although any value in the range of
0 to 255 can be used.
The edges can then be attenuated with the settings in the
ED/HD Adaptive Filter Gain 1, Gain 2, and Gain 3 registers
(Subaddress 0x58, Subaddress 0x59 and Subaddress 0x5A), and
the ED/HD sharpness filter gain register (Subaddress 0x40).
To enhance or attenuate the Y signal in the frequency ranges
shown in Figure 74, the ED/HD sharpness filter must be
enabled (Subaddress 0x31, Bit 7 = 1) and the ED/HD adaptive
filter must be disabled (Subaddress 0x35, Bit 7 = 0).
To select one of the 256 individual responses, the corresponding
gain values, ranging from −8 to +7 for each filter, must be
programmed into the ED/HD sharpness filter gain register at
Subaddress 0x40.
There are two adaptive filter modes available. The mode is
selected using the ED/HD adaptive filter mode control
(Subaddress 0x35, Bit 6):
•
ED/HD Adaptive Filter Mode
In ED/HD adaptive filter mode, the following registers are used:
•
•
•
•
•
•
•
ED/HD Adaptive Filter Threshold A
ED/HD Adaptive Filter Threshold B
ED/HD Adaptive Filter Threshold C
ED/HD Adaptive Filter Gain 1
ED/HD Adaptive Filter Gain 2
ED/HD Adaptive Filter Gain 3
ED/HD sharpness filter gain register
•
Mode A is used when the ED/HD adaptive filter mode
control is set to 0. In this case, Filter B (LPF) is used in the
adaptive filter block. In addition, only the programmed
values for Gain B in the ED/HD sharpness filter gain
register and ED/HD Adaptive Filter Gain 1, Gain 2, and
Gain 3 registers are applied when needed. The Gain A
values are fixed and cannot be changed.
Mode B is used when ED/HD adaptive filter mode control is
set to 1. In this mode, a cascade of Filter A and Filter B is used.
Both settings for Gain A and Gain B in the ED/HD sharpness
filter gain register and ED/HD Adaptive Filter Gain 1, Gain 2,
and Gain 3 registers become active when needed.
1.4
1.4
1.3
1.3
1.2
1.2
1.1
1.0
0.9
1.1
1.0
0.9
0.8
0.8
0.7
0.7
0.6
0.6
0.5
FREQUENCY (MHz)
FILTER A RESPONSE (Gain Ka)
0.5
FREQUENCY (MHz)
FILTER B RESPONSE (Gain Kb)
1.6
1.5
1.4
1.3
1.2
1.1
1.0
0
2
6
8
10
4
FREQUENCY (MHz)
12
FREQUENCY RESPONSE IN SHARPNESS
FILTER MODE WITH Ka = 3 AND Kb = 7
Figure 74. ED/HD Sharpness and Adaptive Filter Control Block
Rev. 0 | Page 55 of 96
06234-074
SHARPNESS AND ADAPTIVE FILTER CONTROL BLOCK
1.5
MAGNITUDE
INPUT SIGNAL:
STEP
MAGNITUDE
1.5
MAGNITUDE RESPONSE (Linear Scale)
To activate the adaptive filter control, the ED/HD sharpness
filter and the ED/HD adaptive filter must be enabled
(Subaddress 0x31, Bit 7 = 1, and Subaddress 0x35, Bit 7 = 1,
respectively).
ADV7390/ADV7391/ADV7392/ADV7393
d
a
R2
1
e
b
R4
R1
f
c
R2
CH1 500mV
REF A
500mV 4.00µs
1
M 4.00µs
9.99978ms
CH1
ALL FIELDS
CH1 500mV
REF A
500mV 4.00µs
1
M 4.00µs
9.99978ms
CH1
ALL FIELDS
06234-075
1
Figure 75. ED/ HD Sharpness Filter Control with Different Gain Settings for ED/HD Sharpness Filter Gain Values
ED/HD SHARPNESS FILTER AND ADAPTIVE FILTER
APPLICATION EXAMPLES
Sharpness Filter Application
The ED/HD sharpness filter can be used to enhance or
attenuate the Y video output signal. The register settings in
Table 46 were used to achieve the results shown in Figure 75.
Input data was generated by an external signal source.
Table 46. ED/HD Sharpness Control
Subaddress
0x00
0x01
0x02
0x30
0x31
0x40
0x40
0x40
0x40
0x40
0x40
1
Register Setting
0xFC
0x10
0x20
0x00
0x81
0x00
0x08
0x04
0x40
0x80
0x22
Reference1
a
b
c
d
e
f
Adaptive Filter Control Application
The register settings in Table 47 are used to obtain the results
shown in Figure 77, that is, to remove the ringing on the input
Y signal, as shown in Figure 76. Input data is generated by an
external signal source.
Table 47. Register Settings for Figure 77
Subaddress
0x00
0x01
0x02
0x30
0x31
0x35
0x40
0x58
0x59
0x5A
0x5B
0x5C
0x5D
See Figure 75.
Rev. 0 | Page 56 of 96
Register Setting
0xFC
0x38
0x20
0x00
0x81
0x80
0x00
0xAC
0x9A
0x88
0x28
0x3F
0x64
ADV7390/ADV7391/ADV7392/ADV7393
06234-076
In DNR mode, if the absolute value of the filter output is
smaller than the threshold, it is assumed to be noise. A
programmable amount (coring gain border, coring gain data) of
this noise signal is subtracted from the original signal. In DNR
sharpness mode, if the absolute value of the filter output is less
than the programmed threshold, it is assumed to be noise as
before. However, if the level exceeds the threshold, now being
identified as a valid signal, a fraction of the signal (coring gain
border, coring gain data) is added to the original signal to boost
high frequency components and sharpen the video image.
In MPEG systems, it is common to process the video information
in blocks of 8 pixels × 8 pixels for MPEG2 systems, or 16 pixels
× 16 pixels for MPEG1 systems (block size control). DNR can
be applied to the resulting block transition areas known to
contain noise. Generally, the block transition area contains two
pixels. It is possible to define this area to contain four pixels
(border area).
Figure 76. Input Signal to ED/HD Adaptive Filter
It is also possible to compensate for variable block positioning
or differences in YCrCb pixel timing with the use of the DNR
block offset.
The digital noise reduction registers are three 8-bit registers.
They are used to control the DNR processing.
DNR MODE
06234-077
DNR CONTROL
BLOCK SIZE CONTROL
BORDER AREA
BLOCK OFFSET
Figure 77. Output Signal from ED/HD Adaptive Filter (Mode A)
GAIN
When changing the adaptive filter mode to Mode B
(Subaddress 0x35, Bit 6), the output shown in Figure 78
can be obtained.
NOISE
SIGNAL PATH
CORING GAIN DATA
CORING GAIN BORDER
INPUT FILTER
BLOCK
FILTER
OUTPUT
< THRESHOLD?
Y DATA
INPUT
FILTER OUTPUT
> THRESHOLD
–
SUBTRACT
SIGNAL IN
THRESHOLD
RANGE FROM
ORIGINAL SIGNAL
+
DNR OUT
MAIN SIGNAL PATH
DNR
SHARPNESS
MODE
DNR CONTROL
BLOCK SIZE CONTROL
BORDER AREA
BLOCK OFFSET
06234-078
GAIN
NOISE
SIGNAL PATH
Figure 78. Output Signal from ED/HD Adaptive Filter (Mode B)
CORING GAIN DATA
CORING GAIN BORDER
INPUT FILTER
BLOCK
Y DATA
INPUT
Subaddress 0xA3 to Subaddress 0xA5
Digital noise reduction (DNR) is applied to the Y data only.
A filter block selects the high frequency, low amplitude components of the incoming signal (DNR input select). The absolute
value of the filter output is compared to a programmable
threshold value (DNR threshold control). There are two DNR
modes available: DNR mode and DNR sharpness mode.
Rev. 0 | Page 57 of 96
ADD SIGNAL
ABOVE
THRESHOLD
RANGE FROM
ORIGINAL SIGNAL
FILTER
OUTPUT
> THRESHOLD?
FILTER OUTPUT
< THRESHOLD
+
+
MAIN SIGNAL PATH
Figure 79. SD DNR Block Diagram
DNR OUT
06234-079
SD DIGITAL NOISE REDUCTION
ADV7390/ADV7391/ADV7392/ADV7393
Coring Gain Border—Subaddress 0xA3, Bits[3:0]
Block Size—Subaddress 0xA4, Bit 7
These four bits are assigned to the gain factor applied to border
areas. In DNR mode, the range of gain values is 0 to 1 in
increments of 1/8. This factor is applied to the DNR filter
output that lies below the set threshold range. The result is then
subtracted from the original signal.
This bit is used to select the size of the data blocks to be
processed. Setting the block size control function to Logic 1
defines a 16 pixel × 16 pixel data block, and Logic 0 defines an
8 pixel × 8 pixel data block, where one pixel refers to two clock
cycles at 27 MHz.
In DNR sharpness mode, the range of gain values is 0 to 0.5 in
increments of 1/16. This factor is applied to the DNR filter
output that lies above the threshold range. The result is added to
the original signal.
DNR Input Select—Subaddress 0xA5, Bits[2:0]
These four bits are assigned to the gain factor applied to the luma
data inside the MPEG pixel block. In DNR mode, the range of
gain values is 0 to 1 in increments of 1/8. This factor is applied
to the DNR filter output that lies below the set threshold range.
The result is then subtracted from the original signal.
In DNR sharpness mode, the range of gain values is 0 to 0.5 in
increments of 1/16. This factor is applied to the DNR filter
output that lies above the threshold range. The result is added to
the original signal.
FILTER D
0.8
FILTER B
FILTER A
0
OFFSET CAUSED
BY VARIATIONS IN
INPUT TIMING
DNR27 TO DNR24 = 0x01 O X X X X X X O O X X X X X X O
Figure 80. SD DNR Offset Control
DNR Threshold—Subaddress 0xA4, Bits[5:0]
These six bits are used to define the threshold value in the range
of 0 to 63. The range is an absolute value.
Border Area—Subaddress 0xA4, Bit 6
When this bit is set to Logic 1, the block transition area can be
defined to consist of four pixels. If this bit is set to Logic 0, the
border transition area consists of two pixels, where one pixel
refers to two clock cycles at 27 MHz.
DATA
0
1
2
3
4
FREQUENCY (MHz)
5
6
Figure 82. SD DNR Input Select
06234-080
OXXXXXXOOXXXXXXO
2-PIXEL
BORDER
0.4
0.2
APPLY BORDER
CORING GAIN
OXXXXXXOOXXXXXXO
DNR Mode—Subaddress 0xA5, Bit 4
This bit controls the DNR mode selected. Logic 0 selects DNR
mode; Logic 1 selects DNR sharpness mode.
DNR works on the principle of defining low amplitude, high
frequency signals as probable noise and subtracting this noise
from the original signal.
In DNR mode, it is possible to subtract a fraction of the signal
that lies below the set threshold, assumed to be noise, from the
original signal. The threshold is set in DNR Register 1.
When DNR sharpness mode is enabled, it is possible to add a
fraction of the signal that lies above the set threshold to the
original signal because this data is assumed to be valid data and
not noise. The overall effect is that the signal is boosted (similar
to using the extended SSAF filter).
Block Offset Control—Subaddress 0xA5, Bits[7:4]
8 × 8 PIXEL BLOCK 8 × 8 PIXEL BLOCK
06234-081
720 × 485 PIXELS
(NTSC)
FILTER C
0.6
06234-082
APPLY DATA
CORING GAIN
1.0
MAGNITUDE
Coring Gain Data—Subaddress 0xA3, Bits[7:4]
These three bits are assigned to select the filter that is applied to
the incoming Y data. The signal that lies in the pass band of the
selected filter is the signal processed by DNR. Figure 82 shows
the filter responses selectable with this control.
Four bits are assigned to this control that allows a shift in the
data block of 15 pixels maximum. The coring gain positions are
fixed. The block offset shifts the data in steps of one pixel such
that the border coring gain factors can be applied at the same
position regardless of variations in input timing of the data.
Figure 81. SD DNR Border Area
Rev. 0 | Page 58 of 96
ADV7390/ADV7391/ADV7392/ADV7393
SD ACTIVE VIDEO EDGE CONTROL
Subaddress 0x82, Bit 7
At the start of active video, the first three pixels are multiplied
by ⅛, ½, and ⅞, respectively. Approaching the end of active
video, the last three pixels are multiplied by ⅞, ½, and ⅛,
respectively. All other active video pixels pass through
unprocessed.
The ADV739x is able to control fast rising and falling signals at
the start and end of active video to minimize ringing.
When the active video edge control feature is enabled
(Subaddress 0x82, Bit 7 = 1), the first three pixels and the last
three pixels of the active video on the luma channel are scaled
so that maximum transitions on these pixels are not possible.
LUMA CHANNEL WITH
ACTIVE VIDEO EDGE
DISABLED
LUMA CHANNEL WITH
ACTIVE VIDEO EDGE
ENABLED
100 IRE
100 IRE
87.5 IRE
50 IRE
06234-083
12.5 IRE
0 IRE
0 IRE
Figure 83. Example of Active Video Edge Functionality
VOLTS
IRE:FLT
100
0.5
50
0
F2
L135
–50
0
2
6
4
8
10
12
06234-084
0
Figure 84. Example of Video Output with Subaddress 0x82, Bit 7 = 0
VOLTS
IRE:FLT
100
0.5
50
0
F2
L135
–50
–2
0
2
4
6
8
10
Figure 85. Example of Video Output with Subaddress 0x82, Bit 7 = 1
Rev. 0 | Page 59 of 96
12
06234-085
0
ADV7390/ADV7391/ADV7392/ADV7393
EXTERNAL HORIZONTAL AND VERTICAL SYNCHRONIZATION CONTROL
For timing synchronization purposes, the ADV739x is able to accept either EAV/SAV time codes embedded in the input pixel data or
external synchronization signals provided on the HSYNC and VSYNC pins (see Table 48). It is also possible to output synchronization
signals on the HSYNC and VSYNC pins (see Table 49 to Table 51).
Table 48. Timing Synchronization Signal Input Options
Signal
SD HSYNC In
SD VSYNC/FIELD In
ED/HD HSYNC In
ED/HD VSYNC/FIELD In
1
Pin
HSYNC
VSYNC
HSYNC
VSYNC
Condition
SD Slave Timing Mode 1, Mode 2, or Mode 3 Selected (Subaddress 0x8A[2:0]).1
SD Slave Timing Mode 1, Mode 2, or Mode 3 Selected (Subaddress 0x8A[2:0]).1
ED/HD Timing Synchronization Inputs Enabled (Subaddress 0x30, Bit 2 = 0).
ED/HD Timing Synchronization Inputs Enabled (Subaddress 0x30, Bit 2 = 0).
SD and ED/HD timing synchronization outputs must also be disabled (Subaddress 0x02[7:6] = 00).
Table 49. Timing Synchronization Signal Output Options
Signal
SD HSYNC Out
SD VSYNC/FIELD Out
ED/HD HSYNC Out
ED/HD VSYNC/FIELD Out
1
2
Pin
HSYNC
VSYNC
HSYNC
VSYNC
Condition
SD Timing Synchronization Outputs enabled (Subaddress 0x02, Bit 6 = 1).1
SD Timing Synchronization Outputs enabled (Subaddress 0x02, Bit 6 = 1).1
ED/HD Timing Synchronization Outputs enabled (Subaddress 0x02, Bit 7 = 1).2
ED/HD Timing Synchronization Outputs enabled (Subaddress 0x02, Bit 7 = 1).2
ED/HD timing synchronization outputs must also be disabled (Subaddress 0x02, Bit 7 = 0).
ED/HD timing synchronization inputs must also be disabled, that is, embedded EAV/SAV timing codes must be enabled (Subaddress 0x30, Bit 2 = 1).
Table 50. HSYNC Output Control1
ED/HD Input Sync
Format (0x30, Bit 2)
x
x
ED/HD HSYNC
Control
(0x34, Bit 1)
x
x
ED/HD Sync
Output Enable
(0x02, Bit 7)
0
0
SD Sync
Output Enable
(0x02, Bit 6)
0
1
0
1
0
0
1
1
x
x
x
1
1
x
1
Signal on HSYNC Pin
Tristate.
Pipelined SD HSYNC.
Pipelined ED/HD HSYNC.
Pipelined ED/HD HSYNC based on
AV Code H bit.
Pipelined ED/HD HSYNC based on
horizontal counter.
Duration
–
See Error! Reference
source not found..
As per HSYNC timing.
Same as line blanking
interval.
Same as embedded
HSYNC.
In all ED/HD standards where there is a HSYNC output, the start of the HSYNC pulse is aligned with the falling edge of the embedded HSYNC in the output video.
Table 51. VSYNC Output Control 1
ED/HD Input
Sync Format
(0x30, Bit 2)
x
x
ED/HD VSYNC
Control
(0x34, Bit 2)
x
x
ED/HD Sync
Output Enable
(0x02, Bit 7)
0
0
SD Sync
Output Enable
(0x02, Bit 6)
0
1
Video Standard
x
Interlaced
0
0
1
x
x
1
0
1
x
1
0
1
x
x
1
1
x
x
1
1
x
All HD interlaced
standards
All ED/HD progressive
standards
All ED/HD standards
except 525p
525p
1
Signal on VSYNC Pin
Tristate.
Pipelined SD VSYNC/Field.
Pipelined ED/HD VSYNC
or field signal.
Pipelined Field signal
based on AV Code F bit.
Pipelined VSYNC based on
AV Code V bit.
Pipelined ED/HD VSYNC
based on vertical counter.
Pipelined ED/HD VSYNC
based on vertical counter.
Duration
–
See Error!
Reference source
not found..
As per VSYNC or
Field signal timing.
Field.
Vertical blanking
interval.
Aligned with
serration lines.
Vertical blanking
interval.
In all ED/HD standards where there is a VSYNC output, the start of the VSYNC pulse is aligned with the falling edge of the embedded VSYNC in the output video.
Rev. 0 | Page 61 of 96
ADV7390/ADV7391/ADV7392/ADV7393
LOW POWER MODE
Subaddress 0x0D, Bits[2:0]
For power sensitive applications, the ADV739x supports an
Analog Devices, Inc. proprietary low power mode of operation.
To utilize this low power mode, the DACs must be operating in
full-drive mode (RSET = 510 Ω, RL = 37.5 Ω). Low power mode is
not available in low drive mode (RSET = 4.12 kΩ, RL = 300 Ω).
Low power mode can be independently enabled or disabled on
each DAC using Subaddress 0x0D, Bits[2:0]. Low power mode
is disabled by default on all DACs.
In low power mode, DAC current consumption is content
dependent, and on a typical video stream, it can be reduced by
as much as 40%. For applications requiring the highest possible
video performance, low power mode should be disabled.
CABLE DETECTION
Subaddress 0x10, Bits[1:0]
The ADV739x includes an Analog Devices, Inc. proprietary
cable detection feature.
The cable detection feature is available on DAC 1 and DAC 2
when operating in full-drive mode (RSET = 510 Ω, RL = 37.5 Ω,
assuming a connected cable). The feature is not available in lowdrive mode (RSET = 4.12 kΩ, RL = 300 Ω). For a DAC to be
monitored, the DAC must be powered up in Subaddress 0x00.
The cable detection feature can be used with all SD, ED, and
HD video standards. It is available for all output configurations,
that is, CVBS, YC, YPrPb, and RGB output configurations.
For CVBS/YC output configurations, both DAC 1 and DAC 2
are monitored, that is, the CVBS and YC luma outputs are
monitored. For YPrPb and RGB output configurations, only
DAC 1 is monitored, that is, the luma or green output is
monitored.
Once per frame, the ADV739x monitors DAC 1 and/or DAC 2,
updating Subaddress 0x10, Bit 0 and/or Bit 1, respectively. If a
cable is detected on one of the DACs, the relevant bit is set to 0.
If not, the bit is set to 1.
DAC AUTO POWER-DOWN
Subaddress 0x10, Bit 4
For CVBS/YC output configurations, if DAC 1 is unconnected,
only DAC 1 powers down. If DAC 2 is unconnected, DAC 2 and
DAC 3 power down.
For YPrPb and RGB output configurations, if DAC 1 is
unconnected, all three DACs are powered down. DAC 2 is not
monitored for YPrPb and RGB output configurations.
Once per frame, DAC 1 and/or DAC 2 are monitored. If a cable
is detected, the appropriate DAC or DACs remain powered up
for the duration of the frame. If no cable is detected, the
appropriate DAC or DACs power down until the next frame,
when the process is repeated.
PIXEL AND CONTROL PORT READBACK
Subaddress 0x13, Subaddress 0x14, Subaddress 0x16
The ADV739x supports the readback of most digital inputs via
the I2C/SPI MPU port. This feature is useful for board-level
connectivity testing with upstream devices.
The pixel port (P[15:0] or P[7:0]), HSYNC, VSYNC, and
SFL/MISO are available for readback via the MPU port.
The readback registers are located at Subaddress 0x13,
Subaddress 0x14, and Subaddress 0x16.
When using this feature, a clock signal should be applied to the
CLKIN pin to register the levels applied to the input pins.
The SD input mode (Subaddress 0x01, Bits[6:4] = 000) must be
selected when using this feature.
RESET MECHANISMS
Subaddress 0x17, Bit 1
A hardware reset is activated with a high-to-low transition on
the RESET pin in accordance with the timing specifications.
This resets all registers to their default values. After a hardware
reset, the MPU port is configured for I2C operation. For correct
device operation, a hardware reset is necessary after power-up.
The ADV739x also has a software reset accessible via the
I2C/SPI MPU port. A software reset is activated by writing a 1
to Subaddress 0x17, Bit 1. This resets all registers to their
default values. This bit is self-clearing, that is, after a 1 has been
written to the bit, the bit automatically returns to 0.
When operating in SPI mode, a software reset does not cause
the device to revert to I2C mode. For this to occur, a hardware
reset via the RESET pin or a power-down needs to occur.
For power sensitive applications, a DAC auto power-down
feature can be enabled using Subaddress 0x10, Bit 4. This
feature is only available when the cable detection feature is
enabled.
With this feature enabled, the cable detection circuitry monitors
DAC 1 and/or DAC 2 once per frame, and if they are
unconnected, automatically powers down some or all of the
DACs. Which DAC or DACs are powered down depends on the
selected output configuration.
A hardware reset is necessary after power-up for correct device
operation. If no hardware reset functionality is required by the
application, the RESET pin can be connected to a RC network
to provide the hardware reset necessary after power-up. After
power-up, the time constant of the RC network holds the
RESET pin low for long enough to cause a reset to take place.
All subsequent resets can be done via software.
Rev. 0 | Page 61 of 96
ADV7390/ADV7391/ADV7392/ADV7393
PRINTED CIRCUIT BOARD LAYOUT AND DESIGN
DAC CONFIGURATIONS
Table 52. ADV739x Output Rates
The ADV739x contains three DACs. All three DACs can be
configured to operate in full-drive mode. Full-drive mode is
defined as 34.7 mA full-scale current into a 37.5 Ω load, RL.
Full-drive is the recommended mode of operation for the DACs.
Input Mode
(0x01, Bits[6:4])
SD
ED
The ADV739x contains a RSET pin. A resistor connected between
the RSET pin and AGND is used to control the full-scale output
current and, therefore, the output voltage levels of DAC 1, DAC 2,
and DAC 3. For full-drive operation, RSET must have a value
of 510 Ω and RL must have a value of 37.5 Ω. For low drive
operation, RSET must have a value of 4.12 kΩ, and RL must have
a value of 300 Ω.
HD
The resistor connected to the RSET pin should have a 1%
tolerance.
Application
SD
VIDEO OUTPUT BUFFER AND OPTIONAL
OUTPUT FILTER
Table 53. Output Filter Requirements
ED
HD
An output buffer is necessary on any DAC that operates in low
drive mode (RSET = 4.12 kΩ, RL = 300 Ω). Analog Devices Inc.
produces a range of op amps suitable for this application, for
example, the AD8061. For more information about line driver
buffering circuits, see the relevant op amp data sheet.
Oversampling
2×
8×
16×
1×
4×
8×
1×
2×
4×
Attenuation
–50 dB @
(MHz)
20.5
101.5
209.5
14.5
95.5
203.5
44.25
118.5
267
10µH
DAC
OUTPUT
3
600Ω
22pF
600Ω
75Ω
1
BNC
OUTPUT
4
An optional reconstruction (anti-imaging) low-pass filter (LPF)
may be required on the ADV739x DAC outputs. The filter
specifications vary with the application. The use of 16× (SD),
8× (ED), or 4× (HD) oversampling can remove the requirement
for a reconstruction filter altogether.
For applications requiring an output buffer and reconstruction
filter, the ADA4430-1 and ADA4411-3 integrated video filter
buffers should be considered.
Cutoff
Frequency
(MHz)
> 6.5
> 6.5
> 6.5
> 12.5
> 12.5
> 12.5
> 30
> 30
> 30
560Ω
560Ω
06234-086
The ADV739x contains a compensation pin, COMP. A 2.2 nF
compensation capacitor should be connected from the COMP
pin to VAA.
Output Rate (MHz)
27
(2×)
108
(8×)
216
(16×)
27
(1×)
108
(4×)
216
(8×)
74.25
(1×)
148.5
(2×)
297
(4×)
Figure 86. Example of Output Filter for SD, 16× Oversampling
4.7µH
DAC
OUTPUT
3
6.8pF
600Ω
75Ω
600Ω
6.8pF
BNC
OUTPUT
1
4
560Ω
560Ω
06234-087
Alternatively, all three DACs can be configured to operate in low
drive mode. Low drive mode is defined as 4.33 mA full-scale
current into a 300 Ω load, RL.
Oversampling
Off
On
On
Off
On
On
Off
On
On
Figure 87. Example of Output Filter for ED, 8× Oversampling
DAC
OUTPUT
3
300Ω
1
4
75Ω
390nH
BNC
OUTPUT
3
33pF
33pF
75Ω
1
500Ω
500Ω
Figure 88. Example of Output Filter for HD, 4× Oversampling
Rev. 0 | Page 62 of 96
06234-088
4
ADV7390/ADV7391/ADV7392/ADV7393
CIRCUIT FREQUENCY RESPONSE
0
0
–10
The ADV739x is a highly integrated circuit containing both
precision analog and high speed digital circuitry. It has been
designed to minimize interference effects on the integrity of the
analog circuitry by the high speed digital circuitry. It is imperative
that these same design and layout techniques be applied to the
system-level design so that optimal performance is achieved.
21n
MAGNITUDE (dB)
–60
–20
18n
–90
–30
PHASE (Degrees)
15n
–120
–40
12n
–150
–50
The layout should be optimized for lowest noise on the
ADV739x power and ground planes by shielding the digital
inputs and providing good power supply decoupling.
9n
–180
GROUP DELAY (Seconds)
–60
6n
–210
–70
–80
1M
3n
–240
0
1G
10M
100M
FREQUENCY (Hz)
06234-089
GAIN (dB)
PRINTED CIRCUIT BOARD (PCB) LAYOUT
24n
–30
Figure 89. Output Filter Plot for SD, 16× Oversampling
CIRCUIT FREQUENCY RESPONSE
0
Component Placement
Component placement should be carefully considered to
separate noisy circuits, such as clock signals and high speed
digital circuitry from analog circuitry.
480
18n
400
–10
MAGNITUDE (dB)
The external loop filter components and components connected
to the COMP and RSET pins should be placed as close as possible
to and on the same side of the PCB as the ADV739x. Adding
vias to the PCB to get the components closer to the ADV739x is
not recommended.
16n
320
–20
14n
GAIN (dB)
–30
GROUP DELAY (Seconds)
–40
240
PHASE
(Degrees)
160
12n
10n
–50
80
–60
0
–70
–80
–80
–160
It is recommended that the ADV739x be placed as close as
possible to the output connector, with the DAC output traces as
short as possible.
8n
6n
4n
2n
10M
–240
0
1G
100M
06234-090
–90
1M
FREQUENCY (Hz)
Figure 90. Output Filter Plot for ED, 8× Oversampling
CIRCUIT FREQUENCY RESPONSE
0
PHASE
(Degrees)
200
120
–30
–40
–40
–120
–50
1
10
100
FREQUENCY (MHz)
Power Supplies
PHASE (Degrees)
40
–200
06234-091
GAIN (dB)
GROUP DELAY (Seconds)
–20
The termination resistors on the DAC output traces should be
placed as close as possible to and on the same side of the PCB as
the ADV739x. The termination resistors should overlay the
PCB ground plane.
External filter and buffer components connected to the DAC
outputs should be placed as close as possible to the ADV739x to
minimize the possibility of noise pickup from neighboring
circuitry, and to minimize the effect of trace capacitance on
output bandwidth. This is particularly important when
operating in low drive mode (RSET = 4.12 kΩ, RL = 300 Ω).
MAGNITUDE (dB)
–10
It is recommended to use a 4-layer printed circuit board with
ground and power planes separating the signal trace layer and
the solder side layer.
It is recommended that a separate regulated supply be provided
for each power domain (VAA, VDD, VDD_IO, and PVDD). For
optimal performance, linear regulators rather than switch mode
regulators should be used. If switch mode regulators must be
used, care must be taken with regard to the quality of the output
voltage in terms of ripple and noise. This is particularly true for
the VAA and PVDD power domains. Each power supply should be
individually connected to the system power supply at a single
point through a suitable filtering device, such as a ferrite bead.
Figure 91. Output Filter Plot for HD, 4× Oversampling
Rev. 0 | Page 63 of 96
ADV7390/ADV7391/ADV7392/ADV7393
Power Supply Decoupling
It is recommended that each power supply pin be decoupled
with 10 nF and 0.1 μF ceramic capacitors. The VAA, PVDD,
VDD_IO, and both VDD pins should be individually decoupled to
ground. The decoupling capacitors should be placed as close as
possible to the ADV739x with the capacitor leads kept as short
as possible to minimize lead inductance.
A 1 μF tantalum capacitor is recommended across the VAA
supply in addition to the 10 nF and 0.1 μF ceramic capacitors.
Power Supply Sequencing
The ADV739x is robust to all power supply sequencing
combinations. Any particular sequence can be used.
Digital Signal Interconnect
The digital signal traces should be isolated as much as possible
from the analog outputs and other analog circuitry. Digital
signal traces should not overlay the VAA or PVDD power planes.
Due to the high clock rates used, avoid long clock traces to the
ADV739x to minimize noise pickup.
Any pull-up termination resistors for the digital inputs should
be connected to the VDD power supply.
Any unused digital inputs should be tied to ground.
Analog Signal Interconnect
DAC output traces should be treated as transmission lines with
appropriate measures taken to ensure optimal performance (for
example, impedance matched traces). The DAC output traces
should be kept as short as possible. The termination resistors on
the DAC output traces should be placed as close as possible to
and on the same side of the PCB as the ADV739x.
To avoid crosstalk between the DAC outputs, it is
recommended that as much space as possible be left between
the traces connected to the DAC output pins. Adding ground
traces between the DAC output traces is also recommended.
Rev. 0 | Page 64 of 96
ADV7390/ADV7391/ADV7392/ADV7393
TYPICAL APPLICATION CIRCUIT
FERRITE BEAD
VDD_IO
33µF
10µF
0.1µF
GND_IO
GND_IO
FERRITE BEAD
PVDD
33µF
GND_IO
10µF
0.1µF
PGND
PGND
FERRITE BEAD
VAA
33µF
10µF
VDD
33µF
DGND
0.01µF
AGND
VAA POWER
SUPPLY
AGND DECOUPLING
1µF
AGND
0.1µF
DGND
PVDD POWER
SUPPLY
DECOUPLING
PGND
0.1µF
10µF
GND_IO
0.01µF
PGND
AGND
AGND
FERRITE BEAD
VDD_IO POWER
SUPPLY
DECOUPLING
0.01µF
0.01µF
DGND
DGND
VDD POWER SUPPLY
DECOUPLING FOR
EACH POWER PIN
NOTES
1. FOR OPTIMUM PERFORMANCE, EXTERNAL COMPONENTS CONNECTED
TO THE COMP, RSET AND DAC OUTPUT PINS SHOULD BE LOCATED
CLOSE TO, AND ON THE SAME SIDE OF THE PCB AS THE ADV739x.
2. WHEN OPERATING IN I2C MODE, THE I2C DEVICE ADDRESS IS
CONFIGURABLE USING THE ALSB/SPI_SS PIN:
ALSB/SPI_SS = 0, I2C DEVICE ADDRESS = 0xD4 OR 0x54
ALSB/SPI_SS = 1, I2C DEVICE ADDRESS = 0xD6 OR 0x56
3. THE RESISTOR CONNECTED TO THE RSET PIN SHOULD HAVE A 1%
TOLERANCE.
4. THE RECOMMENDED MODE OF OPERATION FOR THE DACs IS FULLDRIVE (RSET = 510Ω, RL = 37.5Ω).
VAA
VDD_IO
P0
P1
P2
P3
P4
P5
P6
P7
PVDD
VDD
VDD
VAA
2.2nF
COMP
RSET
ADV739x
510Ω
AGND
PIXEL PORT INPUTS
P8
P9
P10
P11
P12
P13
P14
P15
CONTROL
INPUTS/OUTPUTS
DACs 1 TO 3 FULL DRIVE OPTION
(RECOMMENDED)
OPTIONAL LPF
DAC 1
ADV7392/
ADV7393
ONLY
OPTIONAL LPF
DAC 2
DACs 1 TO 3 LOW DRIVE OPTION
DAC 1
DAC 3
DAC 2
DAC 3
RSET
4.12kΩ
AGND
OPTIONAL LPF
75Ω
75Ω
75Ω
AGND
AGND
AGND
ADA4411-3
75Ω
DAC 1
HSYNC
VSYNC
DAC 1
LPF
300Ω
CLOCK INPUT
CLKIN
AGND
MPU PORT
INPUTS/OUTPUTS
ADA4411-3
SDA/SCLK
SCL/MOSI
SFL/MISO
ALSB/SPI_SS
75Ω
DAC 2
DAC 2
LPF
300Ω
RESET
AGND
EXTERNAL LOOP FILTER
ADA4411-3
12nF
EXT_LF
150nF
75Ω
DAC 3
DAC 3
LPF
170Ω
300Ω
LOOP FILTER COMPONENTS
SHOULD BE LOCATED
AGND PGND DGND DGND GND_IO
CLOSE TO THE EXT_LF
PIN AND ON THE
SAME SIDE OF THE PCB
AS THE ADV739x.
AGND
AGND PGND DGND DGND GND_IO
Figure 92. ADV739x Typical Application Circuit
Rev. 0 | Page 65 of 96
06234-092
PVDD
ADV7390/ADV7391/ADV7392/ADV7393
APPENDIX 1–COPY GENERATION MANAGEMENT SYSTEM
SD CGMS
Subaddress 0x99 to Subaddress 0x9B
The ADV739x supports copy generation management system
(CGMS) that conforms to the EIAJ CPR-1204 and ARIB TR-B15
standards. CGMS data is transmitted on Line 20 of the odd fields
and Line 283 of even fields. Subaddress 0x99, Bits[6:5] control
whether CGMS data is output on odd or even fields or both.
SD CGMS data can only be transmitted when the ADV739x is
configured in NTSC mode. The CGMS data is 20 bits long. The
CGMS data is preceded by a reference pulse of the same
amplitude and duration as a CGMS bit (see Figure 93).
ED CGMS
Subaddress 0x41 to Subaddress 0x43
Subaddress 0x5E to Subaddress 0x6E
525p
When HD CGMS is enabled (Subaddress 0x32, Bit 6 = 1), 1080i
CGMS data is applied to Line 19 and Line 582 of the luminance
vertical blanking interval.
The HD CGMS data registers are at Subaddress 0x41,
Subaddress 0x42, and Subaddress 0x43.
The ADV739x also supports CGMS Type B packets in HD
mode (720p and 1080i) in accordance with CEA-805-A.
When HD CGMS Type B is enabled (Subaddress 0x5E, Bit 0 = 1),
720p CGMS data is applied to Line 23 of the luminance vertical
blanking interval.
When HD CGMS Type B is enabled (Subaddress 0x5E, Bit 0 = 1),
1080i CGMS data is applied to Line 18 and Line 581 of the
luminance vertical blanking interval.
The HD CGMS Type B data registers are at Subaddress 0x5E to
Subaddress 0x6E.
The ADV739x supports copy generation management system
(CGMS) in 525p mode in accordance with EIAJ CPR-1204-1.
When ED CGMS is enabled (Subaddress 0x32, Bit 6 = 1), 525p
CGMS data is inserted on Line 41. The 525p CGMS data
registers are at Subaddress 0x41, Subaddress 0x42, and
Subaddress 0x43.
The ADV739x also supports CGMS Type B packets in 525p
mode in accordance with CEA-805-A.
When ED CGMS Type B is enabled (Subaddress 0x5E, Bit 0 = 1),
525p CGMS Type B data is inserted on Line 40. The 525p CGMS
Type B data registers are at Subaddress 0x5E to Subaddress 0x6E.
625p
The ADV739x supports copy generation management system
(CGMS) in 625p mode in accordance with IEC 62375 (2004).
When ED CGMS is enabled (Subaddress 0x32, Bit 6 = 1), 625p
CGMS data is inserted on Line 43. The 625p CGMS data
registers are at Subaddress 0x42 and Subaddress 0x43.
HD CGMS
Subaddress 0x41 to Subaddress 0x43
Subaddress 0x5E to Subaddress 0x6E
The ADV739x supports copy generation management system
(CGMS) in HD mode (720p and 1080i) in accordance with
EIAJ CPR-1204-2.
CGMS CRC FUNCTIONALITY
If SD CGMS CRC (Subaddress 0x99, Bit 4) or ED/HD CGMS
CRC (Subaddress 0x32, Bit 7) is enabled, the upper six CGMS
data bits (C19 to C14) that comprise the 6-bit CRC check
sequence are automatically calculated on the ADV739x. This
calculation is based on the lower 14 bits (C13 to C0) of the data
in the CGMS data registers, and the result is output with the
remaining 14 bits to form the complete 20 bits of the CGMS
data. The calculation of the CRC sequence is based on the
polynomial x6 + x + 1 with a preset value of 111111.
If SD CGMS CRC or ED/HD CGMS CRC is disabled, all 20 bits
(C19 to C0) are output directly from the CGMS registers (CRC
must be calculated by the user manually).
If ED/HD CGMS Type B CRC (Subaddress 0x5E, Bit 1) is
enabled, the upper six CGMS Type B data bits (P122 to P127)
that comprise the 6-bit CRC check sequence are automatically
calculated on the ADV739x. This calculation is based on the
lower 128 bits (H0 to H5 and P0 to P121) of the data in the
CGMS Type B data registers. The result is output with the
remaining 128 bits to form the complete 134 bits of the CGMS
Type B data. The calculation of the CRC sequence is based on
the polynomial x6 + x + 1 with a preset value of 111111.
If ED/HD CGMS Type B CRC is disabled, all 134 bits (H0 to H5
and P0 to P127) are output directly from the CGMS Type B
registers (CRC must be calculated by the user manually).
When HD CGMS is enabled (Subaddress 0x32, Bit 6 = 1), 720p
CGMS data is applied to Line 24 of the luminance vertical
blanking interval.
Rev. 0 | Page 66 of 96
ADV7390/ADV7391/ADV7392/ADV7393
+100 IRE
CRC SEQUENCE
REF
+70 IRE
C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19
0 IRE
–40 IRE
06234-093
49.1µs ± 0.5µs
11.2µs
2.235µs ± 20ns
Figure 93. Standard Definition CGMS Waveform
CRC SEQUENCE
+700mV
REF
BIT 1 BIT 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BIT 20
70% ± 10%
C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19
0mV
–300mV
21.2µs ± 0.22µs
22T
5.8µs ± 0.15µs
6T
06234-094
T = 1/(fH × 33) = 963ns
fH = HORIZONTAL SCAN FREQUENCY
T ± 30ns
Figure 94. Enhanced Definition (525p) CGMS Waveform
R = RUN-IN
S = START CODE
PEAK WHITE
R
500mV ± 25mV
S
C0 C1
LSB
C2
C3
C4
SYNC LEVEL
C5
C6
C7
C8
C9 C10 C11 C12 C13
MSB
06234-095
13.7µs
5.5µs ± 0.125µs
Figure 95. Enhanced Definition (625p) CGMS Waveform
CRC SEQUENCE
+700mV
REF
70% ± 10%
BIT 1 BIT 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BIT 20
C0
0mV
C2
C3
C4
C5
C6
C7
C8
C9 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19
T ± 30ns
4T
3.128µs ± 90ns
17.2µs ± 160ns
22T
T = 1/(fH × 1650/58) = 781.93ns
fH = HORIZONTAL SCAN FREQUENCY
1H
Figure 96. High Definition (720p) CGMS Waveform
Rev. 0 | Page 67 of 96
06234-096
–300mV
C1
ADV7390/ADV7391/ADV7392/ADV7393
CRC SEQUENCE
+700mV
REF
70% ± 10%
BIT 1 BIT 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BIT 20
C0
C1
0mV
C2
C3
C4
C5
C6
C7
C8
C9 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19
T ± 30ns
22.84µs ± 210ns
22T
T = 1/(fH × 2200/77) = 1.038µs
fH = HORIZONTAL SCAN FREQUENCY
1H
4T
4.15µs ± 60ns
06234-097
–300mV
Figure 97. High Definition (1080i) CGMS Waveform
CRC SEQUENCE
+700mV
BIT 1 BIT 2
P127
P126
P125
P124
.
P123
.
P122
.
P4
P3
P2
P1
P0
H5
H4
H3
BIT 134
H2
H0
70% ± 10%
H1
START
0mV
06234-098
–300mV
NOTES
1. PLEASE REFER TO THE CEA-805-A SPECIFICATION FOR TIMING INFORMATION.
Figure 98. Enhanced Definition (525p) CGMS Type B Waveform
CRC SEQUENCE
+700mV
P127
P126
P125
.
P124
.
P123
.
P122
P4
P3
P2
P1
P0
H5
H4
BIT 134
H3
H2
H1
START BIT 1 BIT 2
H0
70% ±10%
0mV
NOTES
1. PLEASE REFER TO THE CEA-805-A SPECIFICATION FOR TIMING INFORMATION.
Figure 99. High Definition (720p and 1080i) CGMS Type B Waveform
Rev. 0 | Page 68 of 96
06234-099
–300mV
ADV7390/ADV7391/ADV7392/ADV7393
APPENDIX 2–SD WIDE SCREEN SIGNALING
(see Figure 100). The latter portion of Line 23 (after 42.5 μs
from the falling edge of HSYNC) is available for the insertion of
video. WSS data transmission on Line 23 can be enabled using
Subaddress 0x99, Bit 7. It is possible to blank the WSS portion
of Line 23 with Subaddress 0xA1, Bit 7.
Subaddress 0x99, Subaddress 0x9A, Subaddress 0x9B
The ADV739x supports wide screen signaling (WSS)
conforming to the ETSI 300 294 standard. WSS data is
transmitted on Line 23. WSS data can only be transmitted when
the device is configured in PAL mode. The WSS data is 14 bits
long. The function of each of these bits is shown in Table 54.
The WSS data is preceded by a run-in sequence and a start code
Table 54. Function of WSS Bits
Bit Description
Aspect Ratio, Format, Position
13
12
11
10
9
Bit Number
8 7 6 5
Mode
4
3
1
0
0
1
0
1
1
0
2
0
0
0
0
1
1
1
1
0
1
Color Encoding
0
1
Helper Signals
0
1
Reserved
Teletext Subtitles
1
0
0
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
Setting
4:3, full format, N/A
14:9, letterbox, center
14:9, letterbox, top
16:9, letterbox, center
16:9, letterbox, top
>16:9, letterbox, center
14:9, full format, center
16:0, N/A, N/A
Camera mode
Film mode
Normal PAL
Motion Adaptive ColorPlus
Not present
Present
0
0
1
Open Subtitles
0
0
1
1
Surround Sound
No
Yes
No
Subtitles in active image area
Subtitles out of active image area
Reserved
No
Yes
No copyright asserted or unknown
Copyright asserted
Copying not restricted
Copying restricted
0
1
0
1
0
1
Copyright
0
1
Copy Protection
0
1
500mV
RUN-IN
SEQUENCE
START
CODE
W0
W1
W2
W3
W4
W5
W6
W7
W8
W9
W10 W11 W12 W13
ACTIVE
VIDEO
11.0µs
06234-100
38.4µs
42.5µs
Figure 100. WSS Waveform Diagram
Rev. 0 | Page 69 of 96
ADV7390/ADV7391/ADV7392/ADV7393
APPENDIX 3–SD CLOSED CAPTIONING
All pixels inputs are ignored on Line 21 and Line 284 if closed
captioning is enabled.
Subaddress 0x91 to Subaddress 0x94
The ADV739x supports closed captioning conforming to the
standard television synchronizing waveform for color
transmission. When enabled, closed captioning is transmitted
during the blanked active line time of Line 21 of the odd fields
and Line 284 of the even fields. Closed captioning can be
enabled using Subaddress 0x83, Bits[6:5].
The FCC Code of Federal Regulations (CFR) Title 47 Section
15.119 and EIA-608 describe the closed captioning information
for Line 21 and Line 284.
Closed captioning consists of a 7-cycle sinusoidal burst that is
frequency and phase-locked to the caption data. After the clock
run-in signal, the blanking level is held for two data bits and is
followed by a Logic 1 start bit. Sixteen bits of data follow the start
bit. The data consists of two 8-bit bytes (seven data bits, and one
odd parity bit per byte). The data for these bytes is stored in SD
closed captioning registers (Subaddress 0x93 to Subaddress 0x94).
The ADV739x also supports the extended closed captioning
operation, which is active during even fields and encoded on
Line 284. The data for this operation is stored in SD closed
captioning registers (Subaddress 0x91 to Subaddress 0x92).
The ADV739x automatically generates all clock run-in signals
and timing that support closed captioning on Line 21 and Line 284.
10.5 ± 0.25µs
The ADV739x uses a single buffering method. This means that
the closed captioning buffer is only 1-byte deep. Therefore,
there is no frame delay in outputting the closed captioning data
unlike other 2-byte deep buffering systems. The data must be
loaded one line before it is output on Line 21 and Line 284. A
typical implementation of this method is to use VSYNC to
interrupt a microprocessor, which in turn loads the new data
(2 bytes) in every field. If no new data is required for transmission, 0s must be inserted in both data registers; this is called
nulling. It is also important to load control codes, all of which
are double bytes, on Line 21. Otherwise, a TV does not recognize
them. If there is a message such as “Hello World” that has an
odd number of characters, it is important to add a blank
character at the end to make sure that the end-of-caption,
2-byte control code lands in the same field.
12.91µs
7 CYCLES OF
0.5035MHz
CLOCK RUN-IN
TWO 7-BIT + PARITY
ASCII CHARACTERS
(DATA)
P
A
R
I
T
Y
S
T
A D0 TO D6
R
T
50 IRE
D0 TO D6
BYTE 0
40 IRE
P
A
R
I
T
Y
BYTE 1
10.003µs
27.382µs
33.764µs
Figure 101. SD Closed Captioning Waveform, NTSC
Rev. 0 | Page 70 of 96
06234-101
REFERENCE COLOR BURST
(9 CYCLES)
FREQUENCY = FSC = 3.579545MHz
AMPLITUDE = 40 IRE
ADV7390/ADV7391/ADV7392/ADV7393
APPENDIX 4–INTERNAL TEST PATTERN GENERATION
SD TEST PATTERNS
ED/HD TEST PATTERNS
The ADV739x is able to generate SD color bar and black bar
test patterns.
The ADV739x is able to generate ED/HD color bar, black bar,
and hatch test patterns.
The register settings in Table 55 are used to generate an SD NTSC
75% color bar test pattern. All other registers are set as normal/
default. Component YPrPb output is available on DAC 1 to
DAC 3. Upon power-up, the subcarrier frequency registers
default to the appropriate values for NTSC.
The register settings in Table 57 are used to generate an ED
525p hatch test pattern. All other registers are set as normal/
default. Component YPrPb output is available on DAC 1 to
DAC 3. For component RGB output rather than YPrPb output,
0 should be written to Subaddress 0x02, Bit 5.
Table 55. SD NTSC Color Bar Test Pattern Register Writes
Table 57. ED 525p Hatch Test Pattern Register Writes
Subaddress
0x00
0x82
0x84
Subaddress
0x00
0x01
0x31
Setting
0x1C
0xC9
0x40
For CVBS and S-Video (Y/C) output, 0xCB instead of 0xC9
should be written to Subaddress 0x82.
For component RGB output rather than YPrPb output, 0 should
be written to Subaddress 0x02, Bit 5.
To generate an SD NTSC black bar test pattern, the same
settings shown in Table 55 should be used with an additional
write of 0x24 to Subaddress 0x02.
For PAL output of either test pattern, the same settings are used,
except that Subaddress 0x80 is programmed to 0x11 and the
subcarrier frequency (FSC) registers are programmed as shown
in Table 56.
To generate an ED 525p black bar test pattern, the same settings
as shown in Table 57 should be used with an additional write of
0x24 to Subaddress 0x02.
To generate an ED 525p flat field test pattern, the same settings
shown in Table 57 should be used, except that 0x0D should be
written to Subaddress 0x31.
The Y, Cr, and Cb levels for the hatch and flat field test patterns
can be controlled using Subaddress 0x36, Subaddress 0x37, and
Subaddress 0x38, respectively.
For ED/HD standards other than 525p, the same settings as
shown in Table 57 (and subsequent comments) are used except
that Subaddress 0x30, Bits[7:3] are updated as appropriate.
Table 56. PAL FSC Register Writes
Subaddress
0x8C
0x8D
0x8E
0x8F
Description
FSC0
FSC1
FSC2
FSC3
Setting
0x1C
0x10
0x05
Setting
0xCB
0x8A
0x09
0x2A
Note that when programming the FSC registers, the user must
write the values in the sequence FSC0, FSC1, FSC2, FSC3. The full
FSC value to be written is only accepted after the FSC3 write is
complete.
Rev. 0 | Page 71 of 96
ADV7390/ADV7391/ADV7392/ADV7393
APPENDIX 5–SD TIMING
Mode 0 (CCIR-656)—Slave Option (Subaddress 0x8A = X X X X X 0 0 0)
The ADV739x is controlled by the SAV (start of active video) and EAV (end of active video) time codes embedded in the pixel data. All
timing information is transmitted using a 4-byte synchronization pattern. A synchronization pattern is sent immediately before and after
each line during active picture and retrace. If the VSYNC and HSYNC pins are not used, they should be tied high when using this mode.
ANALOG
VIDEO
EAV CODE
SAV CODE
ANCILLARY DATA
(HANC)
4 CLOCK
NTSC/PAL M SYSTEM
(525 LINES/60Hz)
PAL SYSTEM
(625 LINES/50Hz)
8 1 8 1 F 0 0 X C Y C Y C Y C Y C
b
r
b
0 0 0 0 F 0 0 Y b
r
0 F F A A A
0 F F B B B
4 CLOCK
268 CLOCK
4 CLOCK
4 CLOCK
280 CLOCK
1440 CLOCK
1440 CLOCK
06234-102
INPUT PIXELS
C
F 0 0 X 8 1 8 1
Y
Y
r
F 0 0 Y 0 0 0 0
START OF ACTIVE
VIDEO LINE
END OF ACTIVE
VIDEO LINE
Figure 102. SD Timing Mode 0, Slave Option
Mode 0 (CCIR-656)—Master Option (Subaddress 0x8A = X X X X X 0 0 1)
The ADV739x generates H and F signals required for the SAV and EAV time codes in the CCIR-656 standard. The H bit is output on
HSYNC and the F bit is output on VSYNC.
DISPLAY
522
523
DISPLAY
VERTICAL BLANK
524
525
1
2
3
4
5
6
7
8
9
10
11
20
21
22
H
EVEN FIELD
F
ODD FIELD
DISPLAY
260
261
DISPLAY
VERTICAL BLANK
262
263
264
265
266
267
268
269
270
271
272
273
274
283
284
285
F
ODD FIELD
06234-103
H
EVEN FIELD
Figure 103. SD Timing Mode 0, Master Option, NTSC
Rev. 0 | Page 72 of 96
ADV7390/ADV7391/ADV7392/ADV7393
DISPLAY
622
DISPLAY
VERTICAL BLANK
623
624
625
1
2
4
3
5
6
21
7
22
23
H
ODD FIELD
EVEN FIELD
F
DISPLAY
309
DISPLAY
VERTICAL BLANK
310
311
312
313
314
315
316
318
317
319
335
334
320
336
ODD FIELD
F
06234-104
H
EVEN FIELD
Figure 104. SD Timing Mode 0, Master Option, PAL
ANALOG
VIDEO
06234-105
H
F
Figure 105. SD Timing Mode 0, Master Option, Data Transitions
Mode 1—Slave Option (Subaddress 0x8A = X X X X X 0 1 0)
In this mode, the ADV739x accepts horizontal synchronization and odd/even field signals. When HSYNC is low, a transition of the field
input indicates a new frame, that is, vertical retrace. The ADV739x automatically blanks all normally blank lines as per CCIR-624.
HSYNC and FIELD are input on the HSYNC and VSYNC pins, respectively.
DISPLAY
522
523
DISPLAY
VERTICAL BLANK
524
525
1
2
3
4
5
6
7
8
9
10
11
20
21
22
HSYNC
FIELD
EVEN FIELD ODD FIELD
DISPLAY
260
261
DISPLAY
VERTICAL BLANK
262
263
264
265
266
267
268
269
270
271
272
273
274
283
284
285
FIELD
ODD FIELD
06234-106
HSYNC
EVEN FIELD
Figure 106. SD Timing Mode 1,Slave Option, NTSC
Rev. 0 | Page 73 of 96
ADV7390/ADV7391/ADV7392/ADV7393
DISPLAY
622
623
DISPLAY
VERTICAL BLANK
624
625
1
2
4
3
5
6
7
21
22
23
HSYNC
FIELD
EVEN FIELD
ODD FIELD
DISPLAY
309
310
DISPLAY
VERTICAL BLANK
311
312
313
314
315
316
317
318
319
320
334
335
336
ODD FIELD
FIELD
06234-107
HSYNC
EVEN FIELD
Figure 107. SD Timing Mode 1, Slave Option, PAL
Mode 1—Master Option (Subaddress 0x8A = X X X X X 0 1 1)
In this mode, the ADV739x can generate horizontal synchronization and odd/even field signals. When HSYNC is low, a transition of the
field input indicates a new frame, that is, vertical retrace. The ADV739x automatically blanks all normally blank lines as per CCIR-624.
Pixel data is latched on the rising clock edge following the timing signal transitions. HSYNC and FIELD are output on the HSYNC and
VSYNC pins, respectively.
HSYNC
FIELD
Cb
Y
PAL = 132 × CLOCK/2
NTSC = 122 × CLOCK/2
Cr
Y
06234-108
PIXEL
DATA
Figure 108. SD Timing Mode 1, Odd/Even Field Transitions (Master/Slave)
Mode 2— Slave Option (Subaddress 0x8A = X X X X X 1 0 0)
In this mode, the ADV739x accepts horizontal and vertical synchronization signals. A coincident low transition of both HSYNC and
VSYNC inputs indicates the start of an odd field. A VSYNC low transition when HSYNC is high indicates the start of an even field. The
ADV739x automatically blanks all normally blank lines as per CCIR-624. HSYNC and VSYNC are input on the HSYNC and VSYNC
pins, respectively.
Rev. 0 | Page 74 of 96
ADV7390/ADV7391/ADV7392/ADV7393
DISPLAY
522
DISPLAY
VERTICAL BLANK
523
524
525
1
4
3
2
5
7
6
8
10
9
20
11
21
22
HSYNC
VSYNC
ODD FIELD
EVEN FIELD
DISPLAY
260
261
DISPLAY
VERTICAL BLANK
262
263
264
265
266
267
268
269
270
271
272
273
283
274
284
285
VSYNC
06234-109
HSYNC
EVEN FIELD
ODD FIELD
Figure 109. SD Timing Mode 2, Slave Option, NTSC
DISPLAY
622
623
DISPLAY
VERTICAL BLANK
624
625
1
2
3
4
5
6
7
21
22
23
HSYNC
VSYNC
EVEN FIELD
ODD FIELD
DISPLAY
309
310
DISPLAY
VERTICAL BLANK
311
312
313
314
315
316
317
318
319
320
334
335
336
VSYNC
ODD FIELD
06234-110
HSYNC
EVEN FIELD
Figure 110. SD Timing Mode 2, Slave Option, PAL
Mode 2—Master Option (Subaddress 0x8A = X X X X X 1 0 1)
In this mode, the ADV739x can generate horizontal and vertical synchronization signals. A coincident low transition of both HSYNC and
VSYNC inputs indicates the start of an odd field.
A VSYNC low transition when HSYNC is high indicates the start of an even field. The ADV739x automatically blanks all normally blank
lines as per CCIR-624. HSYNC and VSYNC are output on the HSYNC and VSYNC pins, respectively.
HSYNC
VSYNC
Cb
PAL = 132 × CLOCK/2
NTSC = 122 × CLOCK/2
Figure 111. SD Timing Mode 2, Even-to-Odd Field Transition (Master/Slave)
Rev. 0 | Page 75 of 96
Y
Cr
Y
06234-111
PIXEL
DATA
ADV7390/ADV7391/ADV7392/ADV7393
HSYNC
VSYNC
PAL = 864 × CLOCK/2
NTSC = 858 × CLOCK/2
PIXEL
DATA
Cb
Y
Cr
Cb
06234-112
Y
PAL = 132 × CLOCK/2
NTSC = 122 × CLOCK/2
Figure 112. SD Timing Mode 2, Odd-to-Even Field Transition (Master/Slave)
Mode 3—Master/Slave Option (Subaddress 0x8A = X X X X X 1 1 0 or X X X X X 1 1 1)
In this mode, the ADV739x accepts or generates horizontal synchronization and odd/even field signals. When HSYNC is high, a
transition of the field input indicates a new frame, that is, vertical retrace. The ADV739x automatically blanks all normally blank lines as
per CCIR-624. HSYNC and VSYNC are output in master mode and input in slave mode on the HSYNC and VSYNC pins, respectively.
DISPLAY
522
523
DISPLAY
VERTICAL BLANK
524
525
1
2
4
3
5
6
7
8
9
10
20
11
21
22
HSYNC
FIELD
EVEN FIELD
ODD FIELD
DISPLAY
260
DISPLAY
VERTICAL BLANK
261
262
263
264
265
266
267
268
269
270
271
272
273
283
274
285
284
FIELD
ODD FIELD
06234-113
HSYNC
EVEN FIELD
Figure 113. SD Timing Mode 3, NTSC
DISPLAY
622
623
DISPLAY
VERTICAL BLANK
624
625
1
2
3
4
5
6
7
21
22
23
HSYNC
FIELD
EVEN FIELD
ODD FIELD
DISPLAY
309
310
DISPLAY
VERTICAL BLANK
311
312
313
314
315
316
317
318
319
320
334
335
336
FIELD
EVEN FIELD
06234-114
HSYNC
ODD FIELD
Figure 114. SD Timing Mode 3, PAL
Rev. 0 | Page 76 of 96
ADV7390/ADV7391/ADV7392/ADV7393
APPENDIX 6–HD TIMING
DISPLAY
FIELD 1
VERTICAL BLANKING INTERVAL
1124
1125
1
2
3
4
5
6
7
8
20
21
22
560
VSYNC
HSYNC
DISPLAY
VERTICAL BLANKING INTERVAL
FIELD 2
561
562
563
564
565
566
567
568
569
570
583
584
585
1123
06234-115
VSYNC
HSYNC
Figure 115. 1080i HSYNC and VSYNC Input Timing
Rev. 0 | Page 77 of 96
ADV7390/ADV7391/ADV7392/ADV7393
APPENDIX 7–VIDEO OUTPUT LEVELS
SD YPrPb OUTPUT LEVELS—SMPTE/EBU N10
BLACK
BLUE
RED
MAGENTA
GREEN
CYAN
YELLOW
WHITE
BLACK
BLUE
RED
MAGENTA
GREEN
CYAN
YELLOW
WHITE
Pattern: 100% Color Bars
700mV
700mV
300mV
06234-116
06234-119
300mV
BLACK
BLUE
RED
MAGENTA
GREEN
CYAN
WHITE
BLACK
BLUE
RED
MAGENTA
GREEN
CYAN
YELLOW
WHITE
YELLOW
Figure 119. Y Levels—PAL
Figure 116. Y Levels—NTSC
700mV
06234-117
06234-120
700mV
BLACK
BLUE
RED
MAGENTA
GREEN
CYAN
WHITE
BLACK
BLUE
RED
MAGENTA
GREEN
CYAN
YELLOW
WHITE
YELLOW
Figure 120. Pr Levels—PAL
Figure 117. Pr Levels—NTSC
700mV
06234-118
06234-121
700mV
Figure 121. Pb Levels—PAL
Figure 118. Pb Levels—NTSC
Rev. 0 | Page 78 of 96
ADV7390/ADV7391/ADV7392/ADV7393
ED/HD YPrPb OUTPUT LEVELS
INPUT CODE
EIA-770.2, STANDARD FOR Y
INPUT CODE
OUTPUT VOLTAGE
EIA-770.3, STANDARD FOR Y
OUTPUT VOLTAGE
940
940
700mV
700mV
64
64
300mV
300mV
EIA-770.3, STANDARD FOR Pr/Pb
EIA-770.2, STANDARD FOR Pr/Pb
OUTPUT VOLTAGE
OUTPUT VOLTAGE
960
960
600mV
512
700mV
64
06234-122
64
Figure 124. EIA-770.3 Standard Output Signals (1080i/720p)
Figure 122. EIA-770.2 Standard Output Signals (525p/625p)
INPUT CODE
EIA-770.1, STANDARD FOR Y
06234-124
700mV
512
INPUT CODE
OUTPUT VOLTAGE
782mV
Y–OUTPUT LEVELS FOR
FULL INPUT SELECTION
OUTPUT VOLTAGE
1023
940
700mV
714mV
64
64
300mV
286mV
EIA-770.1, STANDARD FOR Pr/Pb
INPUT CODE
OUTPUT VOLTAGE
Pr/Pb–OUTPUT LEVELS FOR
FULL INPUT SELECTION
OUTPUT VOLTAGE
1023
960
700mV
700mV
300mV
Figure 125. Output Levels for Full Input Selection
Figure 123. EIA-770.1 Standard Output Signals (525p/625p)
Rev. 0 | Page 79 of 96
06234-125
64
64
06234-123
512
ADV7390/ADV7391/ADV7392/ADV7393
SD/ED/HD RGB OUTPUT LEVELS
Pattern: 100%/75% Color Bars
R
R
700mV/525mV
700mV/525mV
300mV
300mV
G
G
700mV/525mV
700mV/525mV
300mV
300mV
B
B
06234-126
300mV
300mV
06234-128
700mV/525mV
700mV/525mV
Figure 128. HD RGB Output Levels—RGB Sync Disabled
Figure 126. SD/ED RGB Output Levels—RGB Sync Disabled
R
R
700mV/525mV
600mV
700mV/525mV
300mV
300mV
0mV
0mV
G
G
700mV/525mV
600mV
700mV/525mV
300mV
300mV
0mV
0mV
B
B
700mV/525mV
600mV
700mV/525mV
06234-127
0mV
06234-129
300mV
300mV
0mV
Figure 129. HD RGB Output Levels—RGB Sync Enabled
Figure 127. SD/ED RGB Output Levels—RGB Sync Enabled
Rev. 0 | Page 80 of 96
ADV7390/ADV7391/ADV7392/ADV7393
SD OUTPUT PLOTS
VOLTS
VOLTS IRE:FLT
0.6
100
0.4
0.5
50
0
0.2
0
0
–0.2
F1
L76
20
0
10
20
30
40
50
60
MICROSECONDS
NOISE REDUCTION: 0.00dB
APL = 39.1%
PRECISION MODE OFF
625 LINE NTSC NO FILTERING
SYNCHRONOUS SOUND-IN-SYNC OFF
SLOW CLAMP TO 0.00 AT 6.72µs
FRAMES SELECTED 1, 2, 3, 4
06234-133
30
40
50
60
MICROSECONDS
APL = 44.5%
PRECISION MODE OFF
525 LINE NTSC
SYNCHRONOUS SYNC = A
SLOW CLAMP TO 0.00V AT 6.72μs
µ
FRAMES SELECTED 1, 2
0
10
L608
06234-130
–50
Figure 133. PAL Color Bars (75%)
Figure 130. NTSC Color Bars (75%)
VOLTS
VOLTS IRE:FLT
0.6
0.5
0.4
50
0.2
0
00
F2
L238
10
L575
30
40
50
60
MICROSECONDS
NOISE REDUCTION: 15.05dB
APL = 44.3%
PRECISION MODE OFF
525 LINE NTSC NO FILTERING
SYNCHRONOUS SYNC = SOURCE
SLOW CLAMP TO 0.00V AT 6.72μs
µ
FRAMES SELECTED 1, 2
0
0
20
10
20
30
40
50
60
70
MICROSECONDS
APL NEEDS SYNC SOURCE.
NO BUNCH SIGNAL
625 LINE PAL NO FILTERING
PRECISION MODE OFF
SLOW CLAMP TO 0.00 AT 6.72µs
SYNCHRONOUS SOUND-IN-SYNC OFF
FRAMES SELECTED 1
Figure 131. NTSC Luma
06234-134
–0.2
06234-131
0
Figure 134. PAL Luma
VOLTS IRE:FLT
0.4
50
VOLTS
0.5
0.2
0
0
0
–0.2
–50
–0.4
–0.5
F1
L76
20
06234-132
10
0
10
20
30
40
50
60
MICROSECONDS
APL NEEDS SYNC SOURCE.
NO BUNCH SIGNAL
625 LINE PAL NO FILTERING
PRECISION MODE OFF
SLOW CLAMP TO 0.00 AT 6.72µs
SYNCHRONOUS SOUND-IN-SYNC OFF
FRAMES SELECTED 1
Figure 132. NTSC Chroma
Figure 135. PAL Chroma
Rev. 0 | Page 81 of 96
06234-135
L575
30
40
50
60
MICROSECONDS
NOISE REDUCTION: 15.05dB
PRECISION MODE OFF
APL NEEDS SYNC SOURCE.
SYNCHRONOUS SYNC = B
525 LINE NTSC NO FILTERING
FRAMES SELECTED 1, 2
SLOW CLAMP TO 0.00 AT 6.72µs
0
ADV7390/ADV7391/ADV7392/ADV7393
APPENDIX 8–VIDEO STANDARDS
0HDATUM
SMPTE 274M
ANALOG WAVEFORM
DIGITAL HORIZONTAL BLANKING
*1
272T
4T
ANCILLARY DATA
(OPTIONAL) OR BLANKING CODE
EAV CODE
1920T
DIGITAL
ACTIVE LINE
F 0 0 F C
V b Y C
r
F 0 0 H*
0 0 F
0 0 V
H*
F
F
INPUT PIXELS
4T
SAV CODE
4 CLOCK
SAMPLE NUMBER
2112
C Y
r
4 CLOCK
0
2199
2116 2156
44
188
192
2111
06234-136
FVH* = FVH AND PARITY BITS
SAV/EAV: LINE 1–562: F = 0
SAV/EAV: LINE 563–1125: F = 1
SAV/EAV: LINE 1–20; 561–583; 1124–1125: V = 1
SAV/EAV: LINE 21–560; 584–1123: V = 0
FOR A FRAME RATE OF 30Hz: 40 SAMPLES
FOR A FRAME RATE OF 25Hz: 480 SAMPLES
Figure 136. EAV/SAV Input Data Timing Diagram (SMPTE 274M)
SMPTE 293M
ANALOG WAVEFORM
ANCILLARY DATA
(OPTIONAL)
EAV CODE
F
F 0 0 V
F 0 0 H*
INPUT PIXELS
F 0 0 F
V
F 0 0 H*
4 CLOCK
719
SAMPLE NUMBER
DIGITAL
ACTIVE LINE
SAV CODE
C
C
b Y r
C
Y r Y
4 CLOCK
723 736
0HDATUM
799
853
857 0
719
DIGITAL HORIZONTAL BLANKING
06234-137
FVH* = FVH AND PARITY BITS
SAV: LINE 43–525 = 200H
SAV: LINE 1–42 = 2AC
EAV: LINE 43–525 = 274H
EAV: LINE 1–42 = 2D8
Figure 137. EAV/SAV Input Data Timing Diagram (SMPTE 293M)
522
523
524
ACTIVE
VIDEO
VERTICAL BLANK
525
1
2
5
6
7
8
9
12
13
Figure 138. SMPTE 293M (525p)
Rev. 0 | Page 82 of 96
14
15
16
42
43
44
06234-138
ACTIVE
VIDEO
ADV7390/ADV7391/ADV7392/ADV7393
622
623
ACTIVE
VIDEO
VERTICAL BLANK
624
625
1
2
5
4
6
7
8
9
10
12
11
13
43
44
45
06234-139
ACTIVE
VIDEO
Figure 139. ITU-R BT.1358 (625p)
DISPLAY
747
748
749
1
750
2
4
3
5
6
7
8
25
26
27
744
745
06234-140
VERTICAL BLANKING INTERVAL
Figure 140. SMPTE 296M (720p)
DISPLAY
VERTICAL BLANKING INTERVAL
FIELD 1
1124
1125
1
2
3
4
5
6
7
8
20
21
560
22
DISPLAY
VERTICAL BLANKING INTERVAL
561
562
563
564
565
566
567
568
569
Figure 141. SMPTE 274M (1080i)
Rev. 0 | Page 83 of 96
570
583
584
585
1123
06234-141
FIELD 2
ADV7390/ADV7391/ADV7392/ADV7393
APPENDIX 9–CONFIGURATION SCRIPTS
The scripts listed in the following pages can be used to configure the ADV739x for basic operation. Certain features are enabled by
default. If required for a specific application, further features can be enabled. Table 58 lists the scripts available for SD modes of operation.
Similarly, Table 89 and Table 106 list the scripts available for ED and HD modes of operation, respectively.
STANDARD DEFINITION
Table 58. SD Configuration Scripts
Input Format
525i (NTSC)
525i (NTSC)
Input Data Width
8-Bit SDR
8-Bit SDR
Synchronization Format
EAV/SAV
EAV/SAV
Input Color Space
YCrCb
YCrCb
Output Color Space
YPrPb
CVBS/Y-C (S-Video)
Table Number
Table 59
525i (NTSC)
525i (NTSC)
525i (NTSC)
525i (NTSC)
525i (NTSC)
525i (NTSC)
525i (NTSC)
525i (NTSC)
525i (NTSC)
525i (NTSC)
525i (NTSC)
525i (NTSC)
525i (NTSC)
8-Bit SDR
8-Bit SDR
8-Bit SDR
10-Bit SDR
10-Bit SDR
10-Bit SDR
10-Bit SDR
10-Bit SDR
16-Bit SDR
16-Bit SDR
16-Bit SDR
16-Bit SDR
16-Bit SDR
HSYNC/VSYNC
EAV/SAV
HSYNC/VSYNC
EAV/SAV
HSYNC/VSYNC
HSYNC/VSYNC
EAV/SAV
HSYNC/VSYNC
HSYNC/VSYNC
HSYNC/VSYNC
HSYNC/VSYNC
HSYNC/VSYNC
HSYNC/VSYNC
YCrCb
YCrCb
YCrCb
YCrCb
YCrCb
YCrCb
YCrCb
YCrCb
YCrCb
YCrCb
RGB
RGB
RGB
YPrPb
RGB
RGB
YPrPb
YPrPb
CVBS/ Y-C (S-Video)
RGB
RGB
YPrPb
RGB
YPrPb
CVBS/ Y-C (S-Video)
RGB
Table 60
Table 61
Table 62
Table 63
Table 64
Table 65
Table 66
Table 67
Table 68
Table 69
Table 70
Table 71
Table 72
Table 73
625i (PAL)
625i (PAL)
625i (PAL)
625i (PAL)
625i (PAL)
625i (PAL)
625i (PAL)
625i (PAL)
625i (PAL)
625i (PAL)
625i (PAL)
625i (PAL)
625i (PAL)
625i (PAL)
625i (PAL)
8-Bit SDR
8-Bit SDR
8-Bit SDR
8-Bit SDR
8-Bit SDR
10-Bit SDR
10-Bit SDR
10-Bit SDR
10-Bit SDR
10-Bit SDR
16-Bit SDR
16-Bit SDR
16-Bit SDR
16-Bit SDR
16-Bit SDR
EAV/SAV
EAV/SAV
HSYNC/VSYNC
EAV/SAV
HSYNC/VSYNC
EAV/SAV
HSYNC/VSYNC
HSYNC/VSYNC
EAV/SAV
HSYNC/VSYNC
HSYNC/VSYNC
HSYNC/VSYNC
HSYNC/VSYNC
HSYNC/VSYNC
HSYNC/VSYNC
YCrCb
YCrCb
YCrCb
YCrCb
YCrCb
YCrCb
YCrCb
YCrCb
YCrCb
YCrCb
YCrCb
YCrCb
RGB
RGB
RGB
YPrPb
CVBS/Y-C (S-Video)
YPrPb
RGB
RGB
YPrPb
YPrPb
CVBS/Y-C (S-Video)
RGB
RGB
YPrPb
RGB
YPrPb
CVBS/Y-C (S-Video)
RGB
Table 74
Table 75
Table 76
Table 77
Table 78
Table 79
Table 80
Table 81
Table 82
Table 83
Table 84
Table 85
Table 86
Table 87
Table 88
Table 59. 8-Bit 525i YCrCb In (EAV/SAV), YPrPb Out
Table 60. 8-Bit 525i YCrCb In (EAV/SAV), CVBS/Y-C Out
Subaddress
0x17
0x00
0x01
0x80
Setting
0x02
0x1C
0x00
0x10
Subaddress
0x17
0x00
0x01
0x80
Setting
0x02
0x1C
0x00
0x10
0x82
0xC9
0x82
0xCB
Description
Software reset.
All DACs enabled. PLL enabled (16×).
SD input mode.
NTSC standard. SSAF luma filter
enabled. 1.3 MHz chroma filter enabled.
Pixel data valid. YPrPb out. SSAF PrPb
filter enabled. Active video edge
control enabled. Pedestal enabled.
Rev. 0 | Page 84 of 96
Description
Software reset
All DACs enabled. PLL enabled (16×).
SD input mode.
NTSC standard. SSAF luma filter
enabled. 1.3 MHz chroma filter enabled.
Pixel data valid. CVBS/S-Video out.
SSAF PrPb filter enabled. Active video
edge control enabled. Pedestal enabled.
ADV7390/ADV7391/ADV7392/ADV7393
Table 61. 8-Bit 525i YCrCb In, YPrPb Out
Table 64. 10-Bit 525i YCrCb In (EAV/SAV), YPrPb Out
Subaddress
0x17
0x00
0x01
0x80
Setting
0x02
0x1C
0x00
0x10
Subaddress
0x17
0x00
0x01
0x80
Setting
0x02
0x1C
0x00
0x10
0x82
0xC9
0x82
0xC9
0x8A
0x0C
0x88
0x10
Description
Software reset.
All DACs enabled. PLL enabled (16×).
SD input mode.
NTSC standard. SSAF luma filter
enabled. 1.3 MHz chroma filter enabled.
Pixel data valid. YPrPb out. SSAF PrPb
filter enabled. Active video edge
control enabled. Pedestal enabled.
Timing Mode 2 (Slave). HSYNC/VSYNC
synchronization.
Table 65. 10-Bit 525i YCrCb In, YPrPb Out
Table 62. 8-Bit 525i YCrCb In (EAV/SAV), RGB Out
Subaddress
0x17
0x00
0x01
0x02
Setting
0x02
0x1C
0x00
0x10
0x80
0x10
0x82
0xC9
Description
Software reset.
All DACs enabled. PLL enabled (16×).
SD input mode.
RGB output enabled. RGB output sync
enabled.
NTSC standard. SSAF luma filter
enabled. 1.3 MHz chroma filter enabled.
Pixel data valid. YPrPb out. SSAF PrPb
filter enabled. Active video edge
control enabled. Pedestal enabled.
Table 63. 8-Bit 525i YCrCb In, RGB Out
Subaddress
0x17
0x00
0x01
0x02
Setting
0x02
0x1C
0x00
0x10
0x80
0x10
0x82
0xC9
0x8A
0x0C
Description
Software reset.
All DACs enabled. PLL enabled (16×).
SD input mode.
NTSC standard. SSAF luma filter
enabled. 1.3 MHz chroma filter enabled.
Pixel data valid. YPrPb out. SSAF PrPb
filter enabled. Active video edge
control enabled. Pedestal enabled.
10-bit input enabled.
Description
Software reset.
All DACs enabled. PLL enabled (16×).
SD input mode.
RGB output enabled. RGB output sync
enabled.
NTSC standard. SSAF luma filter
enabled. 1.3 MHz chroma filter enabled.
Pixel data valid. YPrPb out. SSAF PrPb
filter enabled. Active video edge
control enabled. Pedestal enabled.
Timing Mode 2 (Slave). HSYNC/VSYNC
synchronization.
Subaddress
0x17
0x00
0x01
0x80
Setting
0x02
0x1C
0x00
0x10
0x82
0xC9
0x88
0x8A
0x10
0x0C
Description
Software reset.
All DACs enabled. PLL enabled (16×).
SD input mode.
NTSC standard. SSAF luma filter
enabled. 1.3 MHz chroma filter enabled.
Pixel data valid. YPrPb out. SSAF PrPb
filter enabled. Active video edge
control enabled. Pedestal enabled.
10-bit input enabled.
Timing Mode 2 (Slave). HSYNC/VSYNC
synchronization.
Table 66. 10-Bit 525i YCrCb In, CVBS/Y-C Out
Subaddress
0x17
0x00
0x01
0x80
Setting
0x02
0x1C
0x00
0x10
0x82
0xCB
0x88
0x8A
0x10
0x0C
Rev. 0 | Page 85 of 96
Description
Software reset.
All DACs enabled. PLL enabled (16×).
SD input mode.
NTSC standard. SSAF luma filter
enabled. 1.3 MHz chroma filter enabled.
Pixel data valid. CVBS/S-Video out. SSAF
PrPb filter enabled. Active video edge
control enabled. Pedestal enabled.
10-bit input enabled.
Timing Mode 2 (Slave). HSYNC/VSYNC
synchronization.
ADV7390/ADV7391/ADV7392/ADV7393
Table 67. 10-Bit 525i YCrCb In (EAV/SAV), RGB Out
Table 70. 16-Bit 525i YCrCb In, RGB Out
Subaddress
0x17
0x00
0x01
0x02
Setting
0x02
0x1C
0x00
0x10
Subaddress
0x17
0x00
0x01
0x02
Setting
0x02
0x1C
0x00
0x10
0x80
0x10
0x80
0x10
0x82
0xC9
0x82
0xC9
0x88
0x10
0x88
0x8A
0x08
0x0C
Description
Software reset.
All DACs enabled. PLL enabled (16×).
SD input mode.
RGB output enabled. RGB output sync
enabled.
NTSC standard. SSAF luma filter
enabled. 1.3 MHz chroma filter enabled.
Pixel data valid. YPrPb out. SSAF PrPb
filter enabled. Active video edge
control enabled. Pedestal enabled.
10-bit input enabled.
Description
Software reset
All DACs enabled. PLL enabled (16×).
SD input mode.
RGB output enabled. RGB output sync
enabled.
NTSC standard. SSAF luma filter
enabled. 1.3 MHz chroma filter enabled.
Pixel data valid. YPrPb out. SSAF PrPb
filter enabled. Active video edge
control enabled. Pedestal enabled.
16-bit input enabled.
Timing Mode 2 (Slave). HSYNC/VSYNC
synchronization.
Table 68. 10-Bit 525i YCrCb In, RGB Out
Subaddress
0x17
0x00
0x01
0x02
Setting
0x02
0x1C
0x00
0x10
0x80
0x10
0x82
0xC9
0x88
0x8A
0x10
0x0C
Description
Software reset.
All DACs enabled. PLL enabled (16×).
SD input mode.
RGB output enabled. RGB output sync
enabled.
NTSC standard. SSAF luma filter
enabled. 1.3 MHz chroma filter enabled.
Pixel data valid. YPrPb out. SSAF PrPb
filter enabled. Active video edge
control enabled. Pedestal enabled.
10-bit input enabled.
Timing Mode 2 (Slave). HSYNC/VSYNC
synchronization.
Table 71. 16-Bit 525i RGB In, YPrPb Out
Subaddress
0x17
0x00
0x01
0x80
Setting
0x02
0x1C
0x00
0x10
0x82
0xC9
0x87
0x88
0x8A
0x80
0x08
0x0C
Description
Software reset.
All DACs enabled. PLL enabled (16×).
SD input mode.
NTSC standard. SSAF luma filter
enabled. 1.3 MHz chroma filter enabled.
Pixel data valid. YPrPb out. SSAF PrPb
filter enabled. Active video edge
control enabled. Pedestal enabled.
RGB input enabled.
16-bit input enabled.
Timing Mode 2 (Slave). HSYNC/VSYNC
synchronization.
Table 69. 16-Bit 525i YCrCb In, YPrPb Out
Subaddress
0x17
0x00
0x01
0x80
Setting
0x02
0x1C
0x00
0x10
0x82
0xC9
0x88
0x8A
0x08
0x0C
Description
Software reset.
All DACs enabled. PLL enabled (16×).
SD input mode.
NTSC standard. SSAF luma filter
enabled. 1.3 MHz chroma filter enabled.
Pixel data valid. YPrPb out. SSAF PrPb
filter enabled. Active video edge
control enabled. pedestal enabled.
16-bit input enabled.
Timing Mode 2 (Slave). HSYNC/VSYNC
synchronization.
Table 72. 16-Bit 525i RGB In, CVBS/Y-C Out
Subaddress
0x17
0x00
0x01
0x80
Setting
0x02
0x1C
0x00
0x10
0x82
0xCB
0x87
0x88
0x8A
0x80
0x08
0x0C
Rev. 0 | Page 86 of 96
Description
Software reset.
All DACs enabled. PLL enabled (16×).
SD input mode.
NTSC standard. SSAF luma filter
enabled. 1.3 MHz chroma filter enabled.
Pixel data valid. CVBS/S-Video out. SSAF
PrPb filter enabled. Active video edge
control enabled. Pedestal enabled.
RGB input enabled.
16-bit input enabled.
Timing Mode 2 (Slave). HSYNC/VSYNC
synchronization.
ADV7390/ADV7391/ADV7392/ADV7393
Table 73. 16-Bit 525i RGB In, RGB Out
Table 76. 8-Bit 625i YCrCb In, YPrPb Out
Subaddress
0x17
0x00
0x01
0x02
Setting
0x02
0x1C
0x00
0x10
Subaddress
0x17
0x00
0x01
0x80
Setting
0x02
0x1C
0x00
0x11
0x80
0x10
0x82
0xC1
0x82
0xC9
0x8A
0x0C
0x8C
0x8D
0x8E
0x8F
0xCB
0x8A
0x09
0x2A
0x87
0x88
0x8A
0x80
0x08
0x0C
Description
Software reset.
All DACs enabled. PLL enabled (16×).
SD input mode.
RGB output enabled. RGB output sync
enabled.
NTSC standard. SSAF luma filter
enabled. 1.3 MHz chroma filter enabled.
Pixel data valid. YPrPb out. SSAF PrPb
filter enabled. Active video edge
control enabled. Pedestal enabled.
RGB input enabled.
16-bit input enabled.
Timing Mode 2 (Slave). HSYNC/VSYNC
synchronization.
Description
Software reset.
All DACs enabled. PLL enabled (16×).
SD input mode.
PAL standard. SSAF luma filter enabled.
1.3 MHz chroma filter enabled.
Pixel data valid. YPrPb out. SSAF PrPb
filter enabled. Active video edge
control enabled.
Timing Mode 2 (Slave). HSYNC/VSYNC
synchronization.
PAL FSC value.
PAL FSC value.
PAL FSC value.
PAL FSC value.
Table 74. 8-Bit 625i YCrCb In (EAV/SAV), YPrPb Out
Table 77. 8-Bit 625i YCrCb In (EAV/SAV), RGB Out
Subaddress
0x17
0x00
0x01
0x80
Setting
0x02
0x1C
0x00
0x11
Subaddress
0x17
0x00
0x01
0x02
Setting
0x02
0x1C
0x00
0x10
0x82
0xC1
0x80
0x11
0x8C
0x8D
0x8E
0x8F
0xCB
0x8A
0x09
0x2A
0x82
0xC1
0x8C
0x8D
0x8E
0x8F
0xCB
0x8A
0x09
0x2A
Description
Software reset.
All DACs enabled. PLL enabled (16×).
SD input mode.
PAL standard. SSAF luma filter enabled.
1.3 MHz chroma filter enabled.
Pixel data valid. YPrPb out. SSAF PrPb
filter enabled. Active video edge
control enabled.
PAL FSC value.
PAL FSC value.
PAL FSC value.
PAL FSC value.
Description
Software reset.
All DACs enabled. PLL enabled (16×).
SD input mode.
RGB output enabled. RGB output sync
enabled.
PAL standard. SSAF luma filter enabled.
1.3 MHz chroma filter enabled.
Pixel data valid. YPrPb out. SSAF PrPb
filter enabled. Active video edge
control enabled.
PAL FSC value.
PAL FSC value.
PAL FSC value.
PAL FSC value.
Table 75. 8-Bit 625i YCrCb In (EAV/SAV), CVBS/Y-C Out
Subaddress
0x17
0x00
0x01
0x80
Setting
0x02
0x1C
0x00
0x11
0x82
0xC3
0x8C
0x8D
0x8E
0x8F
0xCB
0x8A
0x09
0x2A
Description
Software reset.
All DACs enabled. PLL enabled (16×).
SD input mode.
PAL standard. SSAF luma filter enabled.
1.3 MHz chroma filter enabled.
Pixel data valid. CVBS/S-Video out.
SSAF PrPb filter enabled. Active video
edge control enabled.
PAL FSC value.
PAL FSC value.
PAL FSC value.
PAL FSC value.
Table 78. 8-Bit 625i YCrCb In, RGB Out
Subaddress
0x17
0x00
0x01
0x02
Setting
0x02
0x1C
0x00
0x10
0x80
0x11
0x82
0xC1
0x8A
0x0C
0x8C
0x8D
0x8E
0x8F
0xCB
0x8A
0x09
0x2A
Rev. 0 | Page 87 of 96
Description
Software reset.
All DACs enabled. PLL enabled (16×).
SD input mode.
RGB output enabled. RGB output sync
enabled.
PAL standard. SSAF luma filter enabled.
1.3 MHz chroma filter enabled.
Pixel data valid. YPrPb out. SSAF PrPb
filter enabled. Active video edge
control enabled.
Timing Mode 2 (Slave). HSYNC/VSYNC
synchronization.
PAL FSC value.
PAL FSC value.
PAL FSC value.
PAL FSC value.
ADV7390/ADV7391/ADV7392/ADV7393
Table 79. 10-Bit 625i YCrCb In (EAV/SAV), YPrPb Out
Table 82. 10-Bit 625i YCrCb In (EAV/SAV), RGB Out
Subaddress
0x17
0x00
0x01
0x80
Setting
0x02
0x1C
0x00
0x11
Subaddress
0x17
0x00
0x01
0x02
Setting
0x02
0x1C
0x00
0x10
0x82
0xC1
0x80
0x11
0x88
0x10
0x82
0xC1
0x88
0x8C
0x8D
0x8E
0x8F
0x10
0xCB
0x8A
0x09
0x2A
Description
Software reset.
All DACs enabled. PLL enabled (16×).
SD input mode.
PAL standard. SSAF luma filter enabled.
1.3 MHz chroma filter enabled.
Pixel data valid. YPrPb out. SSAF PrPb
filter enabled. Active video edge
control enabled.
10-bit input enabled.
Table 80. 10-Bit 625i YCrCb In, YPrPb Out
Subaddress
0x17
0x00
0x01
0x80
Setting
0x02
0x1C
0x00
0x11
0x82
0xC1
0x88
0x8A
0x10
0x0C
0x8C
0x8D
0x8E
0x8F
0xCB
0x8A
0x09
0x2A
Description
Software reset.
All DACs enabled. PLL enabled (16×).
SD input mode.
PAL standard. SSAF luma filter enabled.
1.3 MHz chroma filter enabled.
Pixel data valid. YPrPb out. SSAF PrPb
filter enabled. Active video edge
control enabled.
10-bit input enabled.
Timing Mode 2 (Slave). HSYNC/VSYNC
synchronization.
PAL FSC value.
PAL FSC value.
PAL FSC value.
PAL FSC value.
Table 81. 10-Bit 625i YCrCb In, CVBS/Y-C Out
Subaddress
0x17
0x00
0x01
0x80
Setting
0x02
0x1C
0x00
0x11
0x82
0xC3
0x88
0x8A
0x10
0x0C
0x8C
0x8D
0x8E
0x8F
0xCB
0x8A
0x09
0x2A
Description
Software reset.
All DACs enabled. PLL enabled (16×).
SD input mode.
PAL standard. SSAF luma filter enabled.
1.3 MHz chroma filter enabled.
Pixel Data Valid. CVBS/S-Video Out.
SSAF PrPb Filter Enabled. Active Video
Edge Control Enabled.
10-bit input enabled.
Timing Mode 2 (Slave). HSYNC/VSYNC
synchronization.
PAL FSC value.
PAL FSC value.
PAL FSC value.
PAL FSC value.
Description
Software reset.
All DACs enabled. PLL enabled (16×).
SD input mode.
RGB output enabled. RGB output sync
enabled.
PAL standard. SSAF luma filter enabled.
1.3 MHz chroma filter enabled.
Pixel data valid. YPrPb out. SSAF PrPb
filter enabled. Active video edge
control enabled.
10-bit input enabled.
PAL FSC value.
PAL FSC value.
PAL FSC value.
PAL FSC value.
Table 83. 10-Bit 625i YCrCb In, RGB Out
Subaddress
0x17
0x00
0x01
0x02
Setting
0x02
0x1C
0x00
0x10
0x80
0x11
0x82
0xC1
0x88
0x8A
0x10
0x0C
0x8C
0x8D
0x8E
0x8F
0xCB
0x8A
0x09
0x2A
Description
Software reset.
All DACs enabled. PLL enabled (16×).
SD input mode.
RGB output enabled. RGB output sync
enabled.
PAL standard. SSAF luma filter enabled.
1.3 MHz chroma filter enabled.
Pixel data valid. YPrPb out. SSAF PrPb
filter enabled. Active video edge
control enabled.
10-bit input enabled.
Timing Mode 2 (Slave). HSYNC/VSYNC
synchronization.
PAL FSC value.
PAL FSC value.
PAL FSC value.
PAL FSC value.
Table 84. 16-Bit 625i YCrCb In, YPrPb Out
Subaddress
0x17
0x00
0x01
0x80
Setting
0x02
0x1C
0x00
0x11
0x82
0xC1
0x88
0x8A
0x08
0x0C
0x8C
0x8D
0x8E
0x8F
0xCB
0x8A
0x09
0x2A
Rev. 0 | Page 88 of 96
Description
Software reset.
All DACs enabled. PLL enabled (16×).
SD input mode.
PAL standard. SSAF luma filter enabled.
1.3 MHz chroma filter enabled.
Pixel data valid. YPrPb out. SSAF PrPb
filter enabled. Active video edge
control enabled.
16-bit input enabled.
Timing Mode 2 (Slave). HSYNC/VSYNC
synchronization.
PAL FSC value.
PAL FSC value.
PAL FSC value.
PAL FSC value.
ADV7390/ADV7391/ADV7392/ADV7393
Table 85. 16-Bit 625i YCrCb In, RGB Out
Table 87. 16-Bit 625i RGB In, CVBS/Y-C Out
Subaddress
0x17
0x00
0x01
0x02
Setting
0x02
0x1C
0x00
0x10
Subaddress
0x17
0x00
0x01
0x80
Setting
0x02
0x1C
0x00
0x11
0x80
0x11
0x82
0xC3
0x82
0xC1
0x87
0x88
0x8A
0x80
0x08
0x0C
0x8C
0x8D
0x8E
0x8F
0xCB
0x8A
0x09
0x2A
0x88
0x8A
0x08
0x0C
0x8C
0x8D
0x8E
0x8F
0xCB
0x8A
0x09
0x2A
Description
Software reset.
All DACs enabled. PLL enabled (16×).
SD input mode.
RGB output enabled. RGB output sync
enabled.
PAL standard. SSAF luma filter enabled.
1.3 MHz chroma filter enabled.
Pixel data valid. YPrPb out. SSAF PrPb
filter enabled. Active video edge
control enabled.
16-bit input enabled.
Timing Mode 2 (Slave). HSYNC/VSYNC
synchronization.
PAL FSC value.
PAL FSC value.
PAL FSC value.
PAL FSC value.
Description
Software reset.
All DACs enabled. PLL enabled (16×).
SD input mode.
PAL standard. SSAF luma filter enabled.
1.3 MHz chroma filter enabled.
Pixel data valid. CVBS/S-Video out.
SSAF PrPb filter enabled. Active video
edge control enabled.
RGB input enabled.
16-bit input enabled.
Timing Mode 2 (Slave). HSYNC/VSYNC
synchronization.
PAL FSC value.
PAL FSC value.
PAL FSC value.
PAL FSC value.
Table 88. 16-Bit 625i RGB In, RGB Out
Table 86. 16-Bit 625i RGB In, YPrPb Out
Subaddress
0x17
0x00
0x01
0x80
Setting
0x02
0x1C
0x00
0x11
0x82
0xC1
0x87
0x88
0x8A
0x80
0x08
0x0C
0x8C
0x8D
0x8E
0x8F
0xCB
0x8A
0x09
0x2A
Description
Software reset.
All DACs enabled. PLL enabled (16×).
SD input mode.
PAL standard. SSAF luma filter enabled.
1.3 MHz chroma filter enabled.
Pixel data valid. YPrPb out. SSAF PrPb
filter enabled. Active video edge
control enabled.
RGB input enabled.
16-bit input enabled.
Timing Mode 2 (Slave). HSYNC/VSYNC
synchronization.
PAL FSC value.
PAL FSC value.
PAL FSC value.
PAL FSC value.
Subaddress
0x17
0x00
0x01
0x02
Setting
0x02
0x1C
0x00
0x10
0x80
0x11
0x82
0xC1
0x87
0x88
0x8A
0x80
0x08
0x0C
0x8C
0x8D
0x8E
0x8F
0xCB
0x8A
0x09
0x2A
Rev. 0 | Page 89 of 96
Description
Software reset.
All DACs enabled. PLL enabled (16×).
SD input mode.
RGB output enabled. RGB output sync
enabled.
PAL standard. SSAF luma filter enabled.
1.3 MHz chroma filter enabled.
Pixel data valid. YPrPb out. SSAF PrPb
filter enabled. Active video edge
control enabled.
RGB input enabled.
16-bit input enabled.
Timing Mode 2 (Slave). HSYNC/VSYNC
synchronization.
PAL FSC value.
PAL FSC value.
PAL FSC value.
PAL FSC value.
ADV7390/ADV7391/ADV7392/ADV7393
ENHANCED DEFINITION
Table 89. ED Configuration Scripts
Input Format
525p
525p
525p
525p
525p
525p
525p
525p
Input Data Width
8-Bit DDR
8-Bit DDR
10-Bit DDR
10-Bit DDR
16-Bit SDR
16-Bit SDR
16-Bit SDR
16-Bit SDR
Synchronization Format
EAV/SAV
EAV/SAV
EAV/SAV
EAV/SAV
EAV/SAV
HSYNC/VSYNC
EAV/SAV
HSYNC/VSYNC
Input Color Space
YCrCb
YCrCb
YCrCb
YCrCb
YCrCb
YCrCb
YCrCb
YCrCb
Output Color Space
YPrPb
RGB
YPrPb
RGB
YPrPb
YPrPb
RGB
RGB
Table Number
Table 98
Table 100
Table 99
Table 101
Table 90
Table 91
Table 92
Table 93
625p
625p
625p
625p
625p
625p
625p
625p
8-Bit DDR
8-Bit DDR
10-Bit DDR
10-Bit DDR
16-Bit SDR
16-Bit SDR
16-Bit SDR
16-Bit SDR
EAV/SAV
EAV/SAV
EAV/SAV
EAV/SAV
EAV/SAV
HSYNC/VSYNC
EAV/SAV
HSYNC/VSYNC
YCrCb
YCrCb
YCrCb
YCrCb
YCrCb
YCrCb
YCrCb
YCrCb
YPrPb
RGB
YPrPb
RGB
YPrPb
YPrPb
RGB
RGB
Table 102
Table 104
Table 103
Table 105
Table 94
Table 95
Table 96
Table 97
Table 90. 16-Bit 525p YCrCb In (EAV/SAV), YPrPb Out
Table 93. 16-Bit 525p YCrCb In, RGB Out
Subaddress
0x17
0x00
0x01
0x30
Setting
0x02
0x1C
0x10
0x04
Subaddress
0x17
0x00
0x01
0x02
Setting
0x02
0x1C
0x10
0x10
0x31
0x01
0x30
0x00
0x31
0x01
Description
Software reset.
All DACs enabled. PLL enabled (8×).
ED-SDR input mode.
525p @ 59.94 Hz. EAV/SAV synchronization. EIA-770.2 output levels.
Pixel data valid.
Description
Software reset.
All DACs enabled. PLL enabled (8×).
ED-SDR input mode.
RGB output enabled. RGB output sync
enabled.
525p @ 59.94 Hz. HSYNC/VSYNC synchronization. EIA-770.2 output levels.
Pixel data valid.
Table 91. 16-Bit 525p YCrCb In, YPrPb Out
Subaddress
0x17
0x00
0x01
0x30
Setting
0x02
0x1C
0x10
0x00
0x31
0x01
Description
Software reset.
All DACs enabled. PLL enabled (8×).
ED-SDR input mode.
525p @ 59.94 Hz. HSYNC/VSYNC synchronization. EIA-770.2 output levels.
Pixel data valid.
Table 94. 16-Bit 625p YCrCb In (EAV/SAV), YPrPb Out
Subaddress
0x17
0x00
0x01
0x30
Setting
0x02
0x1C
0x10
0x1C
0x31
0x01
Description
Software reset.
All DACs enabled. PLL enabled (8×).
ED-SDR input mode.
625p @ 50 Hz. EAV/SAV synchronization. EIA-770.2 output levels.
Pixel data valid.
Table 92. 16-Bit 525p YCrCb In (EAV/SAV), RGB Out
Subaddress
0x17
0x00
0x01
0x02
Setting
0x02
0x1C
0x10
0x10
0x30
0x04
0x31
0x01
Description
Software reset.
All DACs enabled. PLL enabled (8×).
ED-SDR input mode.
RGB output enabled. RGB output sync
enabled.
525p @ 59.94 Hz. EAV/SAV synchronization. EIA-770.2 output levels.
Pixel data valid.
Table 95. 16-Bit 625p YCrCb In, YPrPb Out
Subaddress
0x17
0x00
0x01
0x30
Setting
0x02
0x1C
0x10
0x18
0x31
0x01
Rev. 0 | Page 90 of 96
Description
Software reset.
All DACs enabled. PLL enabled (8×).
ED-SDR input mode.
625p @ 50 Hz. HSYNC/VSYNC synchronization. EIA-770.2 output levels.
Pixel data valid.
ADV7390/ADV7391/ADV7392/ADV7393
Table 96. 16-Bit 625p YCrCb In (EAV/SAV), RGB Out
Table 100. 8-Bit 525p YCrCb In (EAV/SAV), RGB Out
Subaddress
0x17
0x00
0x01
0x02
Setting
0x02
0x1C
0x10
0x10
Subaddress
0x17
0x00
0x01
Setting
0x02
0x1C
0x20
0x02
0x10
0x30
0x1C
0x30
0x04
0x31
0x01
0x31
0x01
Description
Software reset.
All DACs enabled. PLL enabled (8×).
ED-SDR input mode.
RGB output enabled. RGB output sync
enabled.
625p @ 50 Hz. EAV/SAV synchronization. EIA-770.2 output levels.
Pixel data valid.
Description
Software reset.
All DACs enabled. PLL enabled (8×).
ED-DDR input mode. Luma data
clocked on falling edge of CLKIN.
RGB output enabled. RGB output sync
enabled.
525p @ 59.94 Hz. EAV/SAV synchronization. EIA-770.2 output levels.
Pixel data valid.
Table 97. 16-Bit 625p YCrCb In, RGB Out
Subaddress
0x17
0x00
0x01
0x02
Setting
0x02
0x1C
0x10
0x10
0x30
0x18
0x31
0x01
Description
Software reset.
All DACs enabled. PLL enabled (8×).
ED-SDR input mode.
RGB output enabled. RGB output sync
enabled.
625p @ 50 Hz. HSYNC/VSYNC synchronization. EIA-770.2 output levels.
Pixel data valid.
Table 98. 8-Bit 525p YCrCb In (EAV/SAV), YPrPb Out
Subaddress
0x17
0x00
0x01
Setting
0x02
0x1C
0x20
0x30
0x04
0x31
0x01
Description
Software reset.
All DACs enabled. PLL enabled (8×).
ED-DDR input mode. Luma data
clocked on falling edge of CLKIN.
525p @ 59.94 Hz. EAV/SAV synchronization. EIA-770.2 output levels.
Pixel data valid.
Table 99. 10-Bit 525p YCrCb In (EAV/SAV), YPrPb Out
Subaddress
0x17
0x00
0x01
Setting
0x02
0x1C
0x20
0x30
0x04
0x31
0x33
0x01
0x6C
Description
Software reset.
All DACs enabled. PLL enabled (8×).
ED-DDR input mode. Luma data
clocked on falling edge of CLKIN.
525p @ 59.94 Hz. EAV/SAV synchronization. EIA-770.2 output levels.
Pixel data valid.
10-bit input enabled.
Table 101. 10-Bit 525p YCrCb In (EAV/SAV), RGB Out
Subaddress
0x17
0x00
0x01
Setting
0x02
0x1C
0x20
0x02
0x10
0x30
0x04
0x31
0x33
0x01
0x6C
Description
Software reset.
All DACs enabled. PLL enabled (8×).
ED-DDR input mode. Luma data
clocked on falling edge of CLKIN.
RGB output enabled. RGB output sync
enabled.
525p @ 59.94 Hz. EAV/SAV synchronization. EIA-770.2 output levels.
Pixel data valid.
10-bit input enabled.
Table 102. 8-Bit 625p YCrCb In (EAV/SAV), YPrPb Out
Subaddress
0x17
0x00
0x01
Setting
0x02
0x1C
0x20
0x30
0x1C
0x31
0x01
Description
Software reset.
All DACs enabled. PLL enabled (8×).
ED-DDR input mode. Luma data
clocked on falling edge of CLKIN.
625p @ 50 Hz. EAV/SAV synchronization. EIA-770.2 output levels.
Pixel data valid.
Table 103. 10-Bit 625p YCrCb In (EAV/SAV), YPrPb Out
Subaddress
0x17
0x00
0x01
Setting
0x02
0x1C
0x20
0x30
0x1C
0x31
0x33
0x01
0x6C
Rev. 0 | Page 91 of 96
Description
Software reset.
All DACs enabled. PLL enabled (8×).
ED-DDR input mode. Luma data
clocked on falling edge of CLKIN.
625p @ 50 Hz. EAV/SAV synchronization. EIA-770.2 output levels.
Pixel data valid.
10-bit input enabled.
ADV7390/ADV7391/ADV7392/ADV7393
Table 104. 8-Bit 625p YCrCb In (EAV/SAV), RGB Out
Table 105. 10-Bit 625p YCrCb In (EAV/SAV), RGB Out
Subaddress
0x17
0x00
0x01
Setting
0x02
0x1C
0x20
Subaddress
0x17
0x00
0x01
Setting
0x02
0x1C
0x20
0x02
0x10
0x02
0x10
0x30
0x1C
0x30
0x1C
0x31
0x01
0x31
0x33
0x01
0x6C
Description
Software reset.
All DACs enabled. PLL enabled (8×).
ED-DDR input mode. Luma data
clocked on falling edge of CLKIN.
RGB output enabled. RGB output sync
enabled.
625p @ 50 Hz. EAV/SAV synchronization. EIA-770.2 output levels.
Pixel data valid.
Description
Software reset.
All DACs enabled. PLL enabled (8×).
ED-DDR input mode. Luma data
clocked on falling edge of CLKIN.
RGB output enabled. RGB output sync
enabled.
625p @ 50 Hz. EAV/SAV synchronization. EIA-770.2 output levels.
Pixel data valid.
10-bit input enabled.
HIGH DEFINITION
Table 106. HD Configuration Scripts
Input Format
720p
720p
720p
720p
720p
720p
720p
720p
Input Data Width
8-Bit DDR
8-Bit DDR
10-Bit DDR
10-Bit DDR
16-Bit SDR
16-Bit SDR
16-Bit SDR
16-Bit SDR
Synchronization Format
EAV/SAV
EAV/SAV
EAV/SAV
EAV/SAV
EAV/SAV
HSYNC/VSYNC
EAV/SAV
HSYNC/VSYNC
Input Color Space
YCrCb
YCrCb
YCrCb
YCrCb
YCrCb
YCrCb
YCrCb
YCrCb
Output Color Space
YPrPb
RGB
YPrPb
RGB
YPrPb
YPrPb
RGB
RGB
Table Number
Table 115
Table 117
Table 116
Table 118
Table 107
Table 108
Table 109
Table 110
1080i
1080i
1080i
1080i
1080i
1080i
1080i
1080i
8-Bit DDR
8-Bit DDR
10-Bit DDR
10-Bit DDR
16-Bit SDR
16-Bit SDR
16-Bit SDR
16-Bit SDR
EAV/SAV
EAV/SAV
EAV/SAV
EAV/SAV
EAV/SAV
HSYNC/VSYNC
EAV/SAV
HSYNC/VSYNC
YCrCb
YCrCb
YCrCb
YCrCb
YCrCb
YCrCb
YCrCb
YCrCb
YPrPb
RGB
YPrPb
RGB
YPrPb
YPrPb
RGB
RGB
Table 119
Table 121
Table 120
Table 122
Table 111
Table 112
Table 113
Table 114
Rev. 0 | Page 92 of 96
ADV7390/ADV7391/ADV7392/ADV7393
Table 107. 16-Bit 720p YCrCb In (EAV/SAV), YPrPb Out
Table 112. 16-Bit 1080i YCrCb In, YPrPb Out
Subaddress
0x17
0x00
0x01
0x30
Setting
0x02
0x1C
0x10
0x2C
Subaddress
0x17
0x00
0x01
0x30
Setting
0x02
0x1C
0x10
0x18
0x31
0x01
0x31
0x01
Description
Software reset.
All DACs enabled. PLL enabled (4×).
HD-SDR input mode.
720p @ 60 Hz/59.94 Hz. EAV/SAV synchronization. EIA-770.3 output levels.
Pixel data valid. 4× oversampling.
Table 113. 16-Bit 1080i YCrCb In (EAV/SAV), RGB Out
Table 108. 16-Bit 720p YCrCb In, YPrPb Out
Subaddress
0x17
0x00
0x01
0x30
Setting
0x02
0x1C
0x10
0x28
0x31
0x01
Description
Software reset.
All DACs enabled. PLL enabled (4×).
HD-SDR input mode.
1080i @ 30 Hz/29.97 Hz. HSYNC/VSYNC
synchronization. EIA-770.3 output levels.
Pixel data valid. 4× oversampling.
Description
Software reset.
All DACs enabled. PLL enabled (4×).
HD-SDR input mode.
720p @ 60 Hz/59.94 Hz. HSYNC/VSYNC
synchronization. EIA-770.3 output levels.
Pixel data valid. 4× oversampling.
Subaddress
0x17
0x00
0x01
0x02
Setting
0x02
0x1C
0x10
0x10
0x30
0x6C
0x31
0x01
Description
Software reset.
All DACs enabled. PLL enabled (4×).
HD-SDR input mode.
RGB output enabled. RGB output sync
enabled.
1080i @ 30 Hz/29.97 Hz. EAV/SAV synchronization. EIA-770.3 output levels.
Pixel data valid. 4× oversampling.
Table 109. 16-Bit 720p YCrCb In (EAV/SAV), RGB Out
Subaddress
0x17
0x00
0x01
0x02
Setting
0x02
0x1C
0x10
0x10
0x30
0x2C
0x31
0x01
Description
Software reset.
All DACs enabled. PLL enabled (4×).
HD-SDR input mode.
RGB output enabled. RGB output sync
enabled.
720p @ 60 Hz/59.94 Hz. EAV/SAV synchronization. EIA-770.3 output levels.
Pixel data valid. 4× oversampling.
Table 110. 16-Bit 720p YCrCb In, RGB Out
Subaddress
0x17
0x00
0x01
0x02
Setting
0x02
0x1C
0x10
0x10
0x30
0x28
0x31
0x01
Description
Software reset.
All DACs enabled. PLL enabled (4×).
HD-SDR input mode.
RGB output enabled. RGB output sync
enabled.
720p @ 60 Hz/59.94 Hz. HSYNC/VSYNC
synchronization. EIA-770.3 output levels.
Pixel data valid. 4× oversampling.
Table 111. 16-Bit 1080i YCrCb In (EAV/SAV), YPrPb Out
Subaddress
0x17
0x00
0x01
0x30
Setting
0x02
0x1C
0x10
0x6C
0x31
0x01
Description
Software reset.
All DACs enabled. PLL enabled (4×).
HD-SDR input mode.
1080i @ 30 Hz/29.97 Hz. EAV/SAV synchronization. EIA-770.3 output levels.
Pixel data valid. 4× oversampling.
Table 114. 16-Bit 1080i YCrCb In, RGB Out
Subaddress
0x17
0x00
0x01
0x02
Setting
0x02
0x1C
0x10
0x10
0x30
0x18
0x31
0x01
Description
Software reset.
All DACs enabled. PLL enabled (4×).
HD-SDR input mode.
RGB output enabled. RGB output sync
enabled.
1080i @ 30 Hz/29.97 Hz. HSYNC/VSYNC
synchronization. EIA-770.3 output levels.
Pixel data valid. 4× oversampling.
Table 115. 8-Bit 720p YCrCb In (EAV/SAV), YPrPb Out
Subaddress
0x17
0x00
0x01
Setting
0x02
0x1C
0x20
0x30
0x2C
0x31
0x01
Description
Software reset.
All DACs enabled. PLL enabled (4×).
HD-DDR input mode. Luma data
clocked on falling edge of CLKIN.
720p @ 60 Hz/59.94 Hz. EAV/SAV synchronization. EIA-770.3 output levels.
Pixel data valid. 4× oversampling.
Table 116. 10-Bit 720p YCrCb In (EAV/SAV), YPrPb Out
Subaddress
0x17
0x00
0x01
Setting
0x02
0x1C
0x20
0x30
0x2C
0x31
0x33
0x01
0x6C
Rev. 0 | Page 93 of 96
Description
Software reset.
All DACs enabled. PLL enabled (4×).
HD-DDR input mode. Luma data
clocked on falling edge of CLKIN.
720p @ 60 Hz/59.94 Hz. EAV/SAV synchronization. EIA-770.3 output levels.
Pixel data valid. 4× oversampling.
10-bit input enabled.
ADV7390/ADV7391/ADV7392/ADV7393
Table 117. 8-Bit 720p YCrCb In (EAV/SAV), RGB Out
Table 120. 10-Bit 1080i YCrCb In (EAV/SAV), YPrPb Out
Subaddress
0x17
0x00
0x01
Setting
0x02
0x1C
0x20
Subaddress
0x17
0x00
0x01
Setting
0x02
0x1C
0x20
0x02
0x10
0x30
0x6C
0x30
0x2C
0x31
0x33
0x01
0x6C
0x31
0x01
Description
Software reset.
All DACs enabled. PLL enabled (4×).
HD-DDR input mode. Luma data
clocked on falling edge of CLKIN.
RGB output enabled. RGB output sync
enabled.
720p @ 60 Hz/59.94 Hz. EAV/SAV synchronization. EIA-770.3 output levels.
Pixel data valid. 4× oversampling.
Table 121. 8-Bit 1080i YCrCb In (EAV/SAV), RGB Out
Table 118. 10-Bit 720p YCrCb In (EAV/SAV), RGB Out
Subaddress
0x17
0x00
0x01
Setting
0x02
0x1C
0x20
0x02
0x10
0x30
0x2C
0x31
0x33
0x01
0x6C
Description
Software reset.
All DACs enabled. PLL enabled (4×).
HD-DDR input mode. Luma data
clocked on falling edge of CLKIN.
1080i @ 30 Hz/29.97 Hz. EAV/SAV synchronization. EIA-770.3 output levels.
Pixel data valid. 4× oversampling.
10-bit input enabled.
Description
Software reset.
All DACs enabled. PLL enabled (4×).
HD-DDR input mode. Luma data
clocked on falling edge of CLKIN.
RGB output enabled. RGB output sync
enabled.
720p @ 60 Hz/59.94 Hz. EAV/SAV synchronization. EIA-770.3 output levels.
Pixel data valid. 4× oversampling.
10-bit input enabled.
Subaddress
0x17
0x00
0x01
Setting
0x02
0x1C
0x20
0x02
0x10
0x30
0x6C
0x31
0x01
Description
Software reset.
All DACs enabled. PLL enabled (4×).
HD-DDR input mode. Luma data
clocked on falling edge of CLKIN.
RGB output enabled. RGB output sync
enabled.
1080i @ 30 Hz/29.97 Hz. EAV/SAV synchronization. EIA-770.3 output levels.
Pixel data valid. 4× oversampling.
Table 122. 10-Bit 1080i YCrCb In (EAV/SAV), RGB Out
Table 119. 8-Bit 1080i YCrCb In (EAV/SAV), YPrPb Out
Subaddress
0x17
0x00
0x01
Setting
0x02
0x1C
0x20
0x30
0x6C
0x31
0x01
Description
Software reset.
All DACs enabled. PLL enabled (4×).
HD-DDR input mode. Luma data
clocked on falling edge of CLKIN.
1080i @ 30 Hz/29.97 Hz. EAV/SAV synchronization. EIA-770.3 output levels.
Pixel data valid. 4× oversampling.
Subaddress
0x17
0x00
0x01
Setting
0x02
0x1C
0x20
0x02
0x10
0x30
0x6C
0x31
0x33
0x01
0x6C
Rev. 0 | Page 94 of 96
Description
Software reset.
All DACs enabled. PLL enabled (4×).
HD-DDR input mode. Luma data
clocked on falling edge of CLKIN.
RGB output enabled. RGB output sync
enabled.
1080i @ 30 Hz/29.97 Hz. EAV/SAV synchronization. EIA-770.3 output levels.
Pixel data valid. 4× oversampling.
10-bit input enabled.
ADV7390/ADV7391/ADV7392/ADV7393
OUTLINE DIMENSIONS
0.60 MAX
5.00
BSC SQ
0.60 MAX
PIN 1
INDICATOR
32
25
24
PIN 1
INDICATOR
TOP
VIEW
0.50
BSC
4.75
BSC SQ
0.50
0.40
0.30
17
16
9
0.30
0.23
0.18
SEATING
PLANE
8
0.25 MIN
3.50 REF
EXPOSED PADDLE MUST BE SOLDERED
TO PCB GROUND FOR PROPER
HEAT DISSIPATION, NOISE IMMUNITY AND
MECHANICAL STRENGTH BENEFITS.
0.05 MAX
0.02 NOM
1.00
0.85
0.80
3.25
3.10 SQ
2.95
EXPOSED
PAD
(BOTTOM VIEW)
0.80 MAX
0.65 TYP
12° MAX
1
COPLANARITY
0.08
0.20 REF
COMPLIANT TO JEDEC STANDARDS MO-220-VHHD-2
Figure 142. 32-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
5 mm × 5 mm Body, Very Thin Quad
(CP-32-2)
Dimensions shown in millimeters
6.00
BSC SQ
0.60 MAX
0.60 MAX
31
30
PIN 1
INDICATOR
TOP
VIEW
0.50
BSC
5.75
BCS SQ
0.50
0.40
0.30
12° MAX
1.00
0.85
0.80
PIN 1
INDICATOR
40
1
(BOT TOM VIEW)
10
21
20
0.25 MIN
4.50
REF
0.80 MAX
0.65 TYP
0.05 MAX
0.02 NOM
SEATING
PLANE
0.30
0.23
0.18
0.20 REF
4.25
4.10 SQ
3.95
EXPOSED
PAD
EXPOSED PADDLE MUST BE SOLDERED
TO PCB GROUND FOR PROPER
HEAT DISSIPATION, NOISE IMMUNITY AND
MECHANICAL STRENGTH BENEFITS.
COPLANARITY
0.08
COMPLIANT TO JEDEC STANDARDS MO-220-VJJD-2
Figure 143. 40-Lead Frame Chip Scale Package [LFCSP]
(CP-40)
Dimensions shown in millimeters
Rev. 0 | Page 95 of 96
ADV7390/ADV7391/ADV7392/ADV7393
ORDERING GUIDE
Model
ADV7390BCPZ 2
ADV7390BCPZ-REEL2
ADV7391BCPZ2
ADV7391BCPZ-REEL2
ADV7392BCPZ2
ADV7392BCPZ-REEL2
ADV7393BCPZ2
ADV7393BCPZ-REEL2
EVAL-ADV739xFEZ2, 3
EVAL-ADV7390EBZ2
EVAL-ADV7391EBZ2
EVAL-ADV7392EBZ2
EVAL-ADV7393EBZ2
1
2
3
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Macrovision 1
Anti-Taping
Yes
Yes
No
No
Yes
Yes
No
No
N/A
Yes
No
Yes
No
Package Description
32-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
32-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
32-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
32-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
40-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
40-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
40-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
40-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
ADV739x Evaluation Platform Front-End Board.
ADV7390 Evaluation Board
ADV7391 Evaluation Board
ADV7392 Evaluation Board
ADV7393 Evaluation Board
Package Option
CP-32-2
CP-32-2
CP-32-2
CP-32-2
CP-40
CP-40
CP-40
CP-40
Macrovision-enabled ICs require the buyer to be an approved licensee (authorized buyer) of ICs that are able to output Macrovision Rev 7.1.L1-compliant video.
Z = Pb-free.
To be used in conjunction with any one of the ADV793x evaluation boards; this front-end board contains an Analog Devices decoder and Xilinx Spartan-3 FPGA.
Purchase of licensed I2 C components of Analog Devices or one of its sublicensed Associated Companies conveys a license for the purchaser under the Philips I2C
Patent Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips.
©2006 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D06234-0-10/06(0)
Rev. 0 | Page 96 of 96