bq4014/bq4014Y 256Kx8 Nonvolatile SRAM Features General Description ➤ Data retention in the absence of power The CMOS bq4014 is a nonvolatile 2,097,152-bit static RAM organized as 262,144 words by 8 bits. The integral control circuitry and lithium energy source provide reliable nonvolatility coupled with the unlimited write cycles of standard SRAM. ➤ Automatic write-protection during power-up/power-down cycles ➤ Industry-standard 32-pin 256K x 8 pinout ➤ Conventional SRAM operation; unlimited write cycles ➤ 10-year minimum data retention in absence of power ➤ Battery internally isolated until power is applied Pin Connections The control circuitry constantly monitors the single 5V supply for an out-of-tolerance condition. When VCC falls out of tolerance, the SRAM is unconditionally write-protected to prevent inadvertent write operation. At this time the integral energy Pin Names source is switched on to sustain the memory until after VCC returns valid. The bq4014 uses extremely low standby current CMOS SRAMs, coupled with small lithium coin cells to provide nonvolatility without long write-cycle times and the writecycle limitations associated with EEPROM. The bq4014 requires no external circuitry and is compatible with the industry-standard 2Mb SRAM pinout. Block Diagram A0–A17 Address inputs DQ0–DQ7 Data input/output CE Chip enable input OE Output enable input WE Write enable input NC No connect VCC +5 volt supply input VSS Ground Selection Guide Maximum Access Time (ns) Negative Supply Tolerance bq4014 -85 85 -5% bq4014 -120 120 -5% Part Number Maximum Access Time (ns) Negative Supply Tolerance bq4014Y -85 85 -10% bq4014Y -120 120 -10% Part Number Sept. 1992 1 bq4014/bq4014Y As VCC falls past VPFD and approaches 3V, the control circuitry switches to the internal lithium backup supply, which provides data retention until valid VCC is applied. Functional Description When power is valid, the bq4014 operates as a standard CMOS SRAM. During power-down and power-up cycles, the bq4014 acts as a nonvolatile memory, automatically protecting and preserving the memory contents. When VCC returns to a level above the internal backup cell voltage, the supply is switched back to VCC. After VCC ramps above the VPFD threshold, write-protection continues for a time tCER (120ms maximum) to allow for processor stabilization. Normal memory operation may resume after this time. Power-down/power-up control circuitry constantly monitors the VCC supply for a power-fail-detect threshold VPFD. The bq4014 monitors for VPFD = 4.62V typical for use in systems with 5% supply tolerance. The bq4014Y monitors for VPFD = 4.37V typical for use in systems with 10% supply tolerance. The internal coin cells used by the bq4014 have an extremely long shelf life and provide data retention for more than 10 years in the absence of system power. When VCC falls below the VPFD threshold, the SRAM automatically write-protects the data. All outputs become high impedance, and all inputs are treated as “don’t care.” If a valid access is in process at the time of power-fail detection, the memory cycle continues to completion. If the memory cycle fails to terminate within time tWPT, write-protection takes place. As shipped from Benchmarq, the integral lithium cells are electrically isolated from the memory. (Self-discharge in this condition is approximately 0.5% per year.) Following the first application of VCC, this isolation is broken, and the lithium backup provides data retention on subsequent power-downs. Truth Table Mode CE WE OE I/O Operation Power Not selected H X X High Z Standby Output disable L H H High Z Active Read L H L DOUT Active Write L L X DIN Active Absolute Maximum Ratings Value Unit VCC Symbol DC voltage applied on VCC relative to VSS -0.3 to 7.0 V VT DC voltage applied on any pin excluding VCC relative to VSS -0.3 to 7.0 V TOPR Operating temperature 0 to +70 °C TSTG Storage temperature -40 to +70 °C TBIAS Temperature under bias -10 to +70 °C TSOLDER Soldering temperature +260 °C Note: Parameter Conditions VT ≤ VCC + 0.3 For 10 seconds Permanent device damage may occur if Absolute Maximum Ratings are exceeded. Functional operation should be limited to the Recommended DC Operating Conditions detailed in this data sheet. Exposure to conditions beyond the operational limits for extended periods of time may affect device reliability. Sept. 1992 2 bq4014/bq4014Y Recommended DC Operating Conditions (TA = 0 to 70°C) Symbol Parameter Minimum Typical Maximum Unit 4.5 5.0 5.5 V bq4014Y 4.75 5.0 5.5 V bq4014 0 0 0 V VCC Supply voltage VSS Supply voltage VIL Input low voltage -0.3 - 0.8 V VIH Input high voltage 2.2 - VCC + 0.3 V Note: Typical values indicate operation at TA = 25°C. DC Electrical Characteristics (TA = 0 to 70°C, VCCmin Symbol Notes Parameter ≤ VCC ≤ VCCmax) Minimum Typical Maximum Unit Conditions/Notes ILI Input leakage current - - ±2 µA VIN = VSS to VCC ILO Output leakage current - - ±2 µA CE = VIH or OE = VIH or WE = VIL VOH Output high voltage 2.4 - - V IOH = -1.0 mA VOL Output low voltage - - 0.4 V IOL = 2.1 mA ISB1 Standby supply current - 5 12 mA CE = VIH ISB2 Standby supply current - 2.5 5 mA CE ≥ VCC - 0.2V, 0V ≤ VIN ≤ 0.2V, or VIN ≥ VCC - 0.2 ICC Operating supply current - 75 110 mA Min. cycle, duty = 100%, CE = VIL, II/O = 0mAV, A17 < VIL or A17 > VIH 4.55 4.62 4.75 V bq4014 VPFD Power-fail-detect voltage 4.30 4.37 4.50 V bq4014Y VSO Supply switch-over voltage - 3 - V Note: Typical values indicate operation at TA = 25°C, VCC = 5V. Capacitance (TA = 25°C, F = 1MHz, VCC = 5.0V) Minimum Typical Maximum Unit CI/O Symbol Input/output capacitance - - 40 pF Output voltage = 0V CIN Input capacitance - - 40 pF Input voltage = 0V Note: Parameter These parameters are sampled and not 100% tested. Sept. 1992 3 Conditions bq4014/bq4014Y AC Test Conditions Parameter Test Conditions Input pulse levels 0V to 3.0V Input rise and fall times 5 ns Input and output timing reference levels 1.5 V (unless otherwise specified) Output load (including scope and jig) See Figures 1 and 2 Figure 1. Output Load A Read Cycle Figure 2. Output Load B (TA = 0 to 70°C, VCCmin ≤ VCC ≤ VCCmax) -120 -85 Symbol Parameter Min. Max. Min. Max. Unit 85 - 120 - ns Conditions tRC Read cycle time tAA Address access time - 85 - 120 ns Output load A tACE Chip enable access time - 85 - 120 ns Output load A tOE Output enable to output valid - 45 - 60 ns Output load A tCLZ Chip enable to output in low Z 5 - 5 - ns Output load B tOLZ Output enable to output in low Z 0 - 0 - ns Output load B tCHZ Chip disable to output in high Z 0 35 0 45 ns Output load B tOHZ Output disable to output in high Z 0 25 0 35 ns Output load B tOH Output hold from address change 10 - 10 - ns Output load A Sept. 1992 4 bq4014/bq4014Y Read Cycle No. 1 (Address Access) 1,2 Read Cycle No. 2 (CE Access) 1,3,4 Read Cycle No. 3 (OE Access) 1,5 Notes: 1. WE is held high for a read cycle. 2. Device is continuously selected: CE = OE = VIL. 3. Address is valid prior to or coincident with CE transition low. 4. OE = VIL. 5. Device is continuously selected: CE = VIL. Sept. 1992 5 bq4014/bq4014Y Write Cycle (TA = 0 to 70°C, VCCmin ≤ VCC ≤ VCCmax) -120 -85 Symbol Parameter Min. Max. Min. Max. Units Conditions/Notes tWC Write cycle time 85 - 120 - ns tCW Chip enable to end of write 75 - 100 - ns (1) tAW Address valid to end of write 75 - 100 - ns (1) tAS Address setup time 0 - 0 - ns Measured from address valid to beginning of write. (2) tWP Write pulse width 65 - 85 - ns Measured from beginning of write to end of write. (1) tWR1 Write recovery time (write cycle 1) 5 - 5 - ns Measured from WE going high to end of write cycle. (3) tWR2 Write recovery time (write cycle 2) 15 - 15 - ns Measured from CE going high to end of write cycle. (3) tDW Data valid to end of write 35 - 45 - ns Measured to first low-to-high transition of either CE or WE. tDH1 Data hold time (write cycle 1) 0 - 0 - ns Measured from WE going high to end of write cycle. (4) tDH2 Data hold time (write cycle 2) 10 - 10 - ns Measured from CE going high to end of write cycle. (4) tWZ Write enabled to output in high Z 0 30 0 40 ns I/O pins are in output state. (5) tOW Output active from end of write 0 - 0 - ns I/O pins are in output state. (5) Notes: 1. A write ends at the earlier transition of CE going high and WE going high. 2. A write occurs during the overlap of a low CE and a low WE. A write begins at the later transition of CE going low and WE going low. 3. Either tWR1 or tWR2 must be met. 4. Either tDH1 or tDH2 must be met. 5. If CE goes low simultaneously with WE going low or after WE going low, the outputs remain in high-impedance state. Sept. 1992 6 bq4014/bq4014Y Write Cycle No. 1 (WE-Controlled) 1,2,3 Write Cycle No. 2 (CE-Controlled) 1,2,3,4,5 Notes: 1. CE or WE must be high during address transition. 2. Because I/O may be active (OE low) during this period, data input signals of opposite polarity to the outputs must not be applied. 3. If OE is high, the I/O pins remain in a state of high impedance. 4. Either tWR1 or tWR2 must be met. 5. Either tDH1 or tDH2 must be met. Sept. 1992 7 bq4014/bq4014Y Power-Down/Power-Up Cycle (TA = 0 to 70°C) Symbol Parameter Minimum Typical Maximum Unit tPF VCC slew, 4.75 to 4.25 V 300 - - µs tFS VCC slew, 4.25 to VSO 10 - - µs tPU VCC slew, VSO to VPFD (max.) 0 - - µs tCER Chip enable recovery time 40 80 120 ms tDR Data-retention time in absence of VCC 10 - - years tWPT Write-protect time 40 100 150 µs Notes: Conditions Time during which SRAM is write-protected after VCC passes VPFD on power-up. TA = 25°C. (2) Delay after VCC slews down past VPFD before SRAM is write-protected. 1. Typical values indicate operation at TA = 25°C, VCC = 5V. 2. Batteries are disconnected from circuit until after VCC is applied for the first time. tDR is the accumulated time in absence of power beginning when power is first applied to the device. Caution: Negative undershoots below the absolute maximum rating of -0.3V in battery-backup mode may affect data integrity. Power-Down/Power-Up Timing Sept. 1992 8 bq4014/bq4014Y Data Sheet Revision History (Sept. 1992 Changes From Sept. 1990) Clarification of ICC test conditions, page 3. MB: 32-Pin B-Type Module 32-Pin MB (B-Type Module) Dimension Minimum Maximum A A1 B 0.365 0.015 0.017 0.375 0.023 C D E e 0.008 2.070 0.710 0.590 0.013 2.100 0.740 0.630 G 0.090 L 0.120 S 0.275 All dimensions are in inches. Sept. 1992 9 0.110 0.150 0.310 bq4014/bq4014Y Ordering Information bq4014 MB Temperature: blank = Commercial (0 to +70°C) Speed Options: 85 = 85 ns 120 = 120 ns Package Option: MB = B-type module Supply Tolerance: no mark = 5% negative supply tolerance Y = 10% negative supply tolerance Device: bq4014 256K x 8 NVSRAM Sept. 1992 10 PACKAGE OPTION ADDENDUM www.ti.com 18-Mar-2008 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty BQ4014MB-120 NRND DIP MOD ULE MB 32 1 TBD CU SN N / A for Pkg Type BQ4014MB-85 NRND DIP MOD ULE MB 32 1 Pb-Free (RoHS) CU SN N / A for Pkg Type BQ4014YMB-120 NRND DIP MOD ULE MB 32 1 TBD CU SN N / A for Pkg Type BQ4014YMB-85 NRND DIP MOD ULE MB 32 10 TBD CU SN N / A for Pkg Type Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 MECHANICAL DATA MPDI062 – MAY 2001 MB (R-PDIP-T32) PLASTIC DUAL-IN-LINE Millimeters Inches Dimension Min. Max. Min. Max. A 0.365 0.375 9.27 A1 0.015 – 0.38 9.53 – B 0.017 0.023 0.43 0.58 C 0.008 0.013 0.20 0.33 D 2.070 2.100 52.58 53.34 E 0.710 0.740 18.03 18.80 e G 0.590 0.630 14.99 16.00 0.090 0.110 2.29 2.79 L 0.120 0.150 3.05 3.81 S 0.275 0.310 6.99 7.87 D E A L A1 C B e S G 4201976/A 03/01 NOTES: A. All linear dimensions are in inches (mm). B. This drawing is subject to change without notice. • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443 • 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID RF/IF and ZigBee® Solutions amplifier.ti.com dataconverter.ti.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lprf Applications Audio Automotive Broadband Digital Control Medical Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/medical www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2008, Texas Instruments Incorporated